This document discusses the design of nuclear reactor pressure vessels. It assesses how varying the height and radius of the pressure vessel affects reactor stability and safety. The results of statistical analysis show that a pressure vessel with a height up to 16m and radius up to 5.6m promises stability, with the temperature reaching a maximum at that point. The safety margin prediction of 3.1% validated for typical pressure vessel models is an advantage over the current 5.1% challenging safety margin limit faced by plant engineers. The document also discusses pressure vessel materials, shapes, stresses, thermal expansion effects, and other factors related to pressure vessel and reactor design.
Capital project EPC service in pressure vessels & heat exchangers.
Turn around EPC service in replacement of pressure vessels & heat exchangers.
Pressure vessels and heat exchangers design & engineering.
Pressure vessels & heat exchangers re-rating.
Stress analysis to pressure vessels and other equipment.
Fitness for Service Assessment (FFS) in level 1, 2, & 3 per API 579-1/ASME FFS-1.
A pressure vessel is a container designed to hold gases or liquids at a pressure substantially different from the ambient pressure. The presentation involves the various understanding aspects of the design of a pressure vessel.
Design and Analysis of Pressure Vessel Using Finite Element MethodIJLT EMAS
Pressure vessel is used to carry liquids such as petrol,
kerosene, aviation fuel etc and these fuel tanks are used to
transport fuel. Finite element method is a mathematical
technique used to design a fuel carrying vessel and performing
the stress analysis. In this the geometrical model is created and
the model is sub divided into smaller elements. It is subjected to
internal pressure and these Boundary conditions are applied at
specified points. The aim of this paper is to design a model and
analysis of fuel carrying tank using finite element analysis
software and also select a proper material composition for
pressure vessel.
Designing is validated according to maximum principal stress
theory and Distortion theory by taking design factor or factor of
safety. The comparisons also made between the calculation
results and software results.
Design by Analysis - A general guideline for pressure vesselAnalyzeForSafety
This presentation file is provided by Mr. Ghanbari and published under permission.
The presentation gives an introduction and general guideline for pressure vessel design by analysis.
The “design by analysis” procedures are intended to guard against eight possible pressure vessel failure modes by performing a detailed stress analysis of the vessel with the sufficient design factors. The failure modes are:
1.excessive elastic deformation, including elastic instability,
2.excessive plastic deformation,
3.brittle fracture,
4.stress rupture/creep deformation (inelastic),
5.plastic instability - incremental collapse,
6.high strain - low cycle fatigue,
7.stress corrosion, and
8.corrosion fatigue
Most of the “design by analysis” procedures that are given in ASME BPVC relate to designs based on “elastic analysis.”
The design-by-analysis requirements are organized based on protection against the failure modes listed below. The component shall be evaluated for each applicable failure mode. If multiple assessment procedures are provided for a failure mode, only one of these procedures must be satisfied to qualify the design of a component.
a)All pressure vessels within the scope of this Division, irrespective of size or pressure, shall be provided with protection against overpressure in accordance with the requirements of this Part.
b)Protection Against Plastic Collapse – these requirements apply to all components where the thickness and configuration of the component is established using design-by-analysis rules.
c)Protection Against Local Failure – these requirements apply to all components where the thickness and configuration of the component is established using design-by-analysis rules. It is not necessary to evaluate the local strain limit criterion if the component design is in accordance with Part 4 (i.e. component wall thickness and weld detail per paragraph 4.2).
d)Protection Against Collapse From Buckling – these requirements apply to all components where the thickness and configuration of the component is established using design-by-analysis rules and the applied loads result in a compressive stress field.
e)Protection Against Failure From Cyclic Loading – these requirements apply to all components where the thickness and configuration of the component is established using design-by-analysis rules and the applied loads are cyclic. In addition, these requirements can also be used to qualify a component for cyclic loading where the thickness and size of the component are established using the design-by-rule requirements of Part 4.
Capital project EPC service in pressure vessels & heat exchangers.
Turn around EPC service in replacement of pressure vessels & heat exchangers.
Pressure vessels and heat exchangers design & engineering.
Pressure vessels & heat exchangers re-rating.
Stress analysis to pressure vessels and other equipment.
Fitness for Service Assessment (FFS) in level 1, 2, & 3 per API 579-1/ASME FFS-1.
A pressure vessel is a container designed to hold gases or liquids at a pressure substantially different from the ambient pressure. The presentation involves the various understanding aspects of the design of a pressure vessel.
Design and Analysis of Pressure Vessel Using Finite Element MethodIJLT EMAS
Pressure vessel is used to carry liquids such as petrol,
kerosene, aviation fuel etc and these fuel tanks are used to
transport fuel. Finite element method is a mathematical
technique used to design a fuel carrying vessel and performing
the stress analysis. In this the geometrical model is created and
the model is sub divided into smaller elements. It is subjected to
internal pressure and these Boundary conditions are applied at
specified points. The aim of this paper is to design a model and
analysis of fuel carrying tank using finite element analysis
software and also select a proper material composition for
pressure vessel.
Designing is validated according to maximum principal stress
theory and Distortion theory by taking design factor or factor of
safety. The comparisons also made between the calculation
results and software results.
Design by Analysis - A general guideline for pressure vesselAnalyzeForSafety
This presentation file is provided by Mr. Ghanbari and published under permission.
The presentation gives an introduction and general guideline for pressure vessel design by analysis.
The “design by analysis” procedures are intended to guard against eight possible pressure vessel failure modes by performing a detailed stress analysis of the vessel with the sufficient design factors. The failure modes are:
1.excessive elastic deformation, including elastic instability,
2.excessive plastic deformation,
3.brittle fracture,
4.stress rupture/creep deformation (inelastic),
5.plastic instability - incremental collapse,
6.high strain - low cycle fatigue,
7.stress corrosion, and
8.corrosion fatigue
Most of the “design by analysis” procedures that are given in ASME BPVC relate to designs based on “elastic analysis.”
The design-by-analysis requirements are organized based on protection against the failure modes listed below. The component shall be evaluated for each applicable failure mode. If multiple assessment procedures are provided for a failure mode, only one of these procedures must be satisfied to qualify the design of a component.
a)All pressure vessels within the scope of this Division, irrespective of size or pressure, shall be provided with protection against overpressure in accordance with the requirements of this Part.
b)Protection Against Plastic Collapse – these requirements apply to all components where the thickness and configuration of the component is established using design-by-analysis rules.
c)Protection Against Local Failure – these requirements apply to all components where the thickness and configuration of the component is established using design-by-analysis rules. It is not necessary to evaluate the local strain limit criterion if the component design is in accordance with Part 4 (i.e. component wall thickness and weld detail per paragraph 4.2).
d)Protection Against Collapse From Buckling – these requirements apply to all components where the thickness and configuration of the component is established using design-by-analysis rules and the applied loads result in a compressive stress field.
e)Protection Against Failure From Cyclic Loading – these requirements apply to all components where the thickness and configuration of the component is established using design-by-analysis rules and the applied loads are cyclic. In addition, these requirements can also be used to qualify a component for cyclic loading where the thickness and size of the component are established using the design-by-rule requirements of Part 4.
A seminar presentation for major or minor project for BTech/MTech students on design of pressure vessels using composite materials. for complete presentation log on to www.mechieprojects.com
Learn how we design these components for high temperature, high pressure, and/or corrosive environments. Discover the different materials used based on a variety of applications. View some of the very unique and intricate Sweco custom designs, and corresponding technical drawings. Sweco designs and manufactures Pressure Vessels and Tanks, Pig Launchers and Receivers, Duct Work, Transition Pieces, Bellmouth Reducers, Spectacle and Line Blinds, Air Intake Stacks and Dampers, Conical Strainers, Instrument Stands and other custom fabricated products.
Design & Stress Analysis of a Cylinder with Closed ends using ANSYSIJERA Editor
The significance of the title of the project comes to front with designing structure of the pressure vessel for static loading and its assessment by ANSYS , is basically a project concerned with design of different pressure vessel elements such as shell, Dish end ,operating manhole ,support leg based on standards and codes ; and evolution of shell and dish end analysed by means of ANSYS .The key feature included in the project is to check the behaviour of pressure vessel in case of fluctuating load . The procedural step includes various aspects such as selecting the material based on American Society of Mechanical Engineers (ASME) codes ,and then designing on the standards procedures with referring standard manuals based on ASME .Further we have included the different manufacturing methods practice by the industries and different aspects of it .
Capital project EPC service in pressure vessels & heat exchangers.
Turn around EPC service in replacement of pressure vessels & heat exchangers.
Pressure vessels and heat exchangers design & engineering.
Pressure vessels & heat exchangers re-rating.
Stress analysis to pressure vessels and other equipment.
Fitness for Service Assessment (FFS) in level 1, 2, & 3 per API 579-1/ASME FFS-1.
Static and Fatigue Analysis of Pressure Vessel as per ASME CodesUtsav Patel
The problem statement is to design a pressure vessel working as an adsorber in a chemical plant. Design data calculated as per ASME BPVC Section VIII/Division I and it analyzed as per ASME BPVC Section VIII/Division II. You can trust this data.
If you need any help regarding this, contact me via LinkedIn.
Chemical Engineering Apparatus Design lecture noteMuktar Abdu
-mechanical design of process equipments
-Internal pressure of pressure vessel
-Thick and thin walled pressure vessels
-application area of thin and thick walled pressure vessels
-Principal stresses formed by internal pressure
-Radial,longitudinal and circumferential stresses
-maximum allowable thickness
-parameters of pressure design
A seminar presentation for major or minor project for BTech/MTech students on design of pressure vessels using composite materials. for complete presentation log on to www.mechieprojects.com
Learn how we design these components for high temperature, high pressure, and/or corrosive environments. Discover the different materials used based on a variety of applications. View some of the very unique and intricate Sweco custom designs, and corresponding technical drawings. Sweco designs and manufactures Pressure Vessels and Tanks, Pig Launchers and Receivers, Duct Work, Transition Pieces, Bellmouth Reducers, Spectacle and Line Blinds, Air Intake Stacks and Dampers, Conical Strainers, Instrument Stands and other custom fabricated products.
Design & Stress Analysis of a Cylinder with Closed ends using ANSYSIJERA Editor
The significance of the title of the project comes to front with designing structure of the pressure vessel for static loading and its assessment by ANSYS , is basically a project concerned with design of different pressure vessel elements such as shell, Dish end ,operating manhole ,support leg based on standards and codes ; and evolution of shell and dish end analysed by means of ANSYS .The key feature included in the project is to check the behaviour of pressure vessel in case of fluctuating load . The procedural step includes various aspects such as selecting the material based on American Society of Mechanical Engineers (ASME) codes ,and then designing on the standards procedures with referring standard manuals based on ASME .Further we have included the different manufacturing methods practice by the industries and different aspects of it .
Capital project EPC service in pressure vessels & heat exchangers.
Turn around EPC service in replacement of pressure vessels & heat exchangers.
Pressure vessels and heat exchangers design & engineering.
Pressure vessels & heat exchangers re-rating.
Stress analysis to pressure vessels and other equipment.
Fitness for Service Assessment (FFS) in level 1, 2, & 3 per API 579-1/ASME FFS-1.
Static and Fatigue Analysis of Pressure Vessel as per ASME CodesUtsav Patel
The problem statement is to design a pressure vessel working as an adsorber in a chemical plant. Design data calculated as per ASME BPVC Section VIII/Division I and it analyzed as per ASME BPVC Section VIII/Division II. You can trust this data.
If you need any help regarding this, contact me via LinkedIn.
Chemical Engineering Apparatus Design lecture noteMuktar Abdu
-mechanical design of process equipments
-Internal pressure of pressure vessel
-Thick and thin walled pressure vessels
-application area of thin and thick walled pressure vessels
-Principal stresses formed by internal pressure
-Radial,longitudinal and circumferential stresses
-maximum allowable thickness
-parameters of pressure design
2018 Hydrogen & Fuel Cells Energy Summit - Haskel Unveils New Hydrogen Techno...Haskel International
At the 2018 Hydrogen & Fuel Cells Energy Summit in Brussels, Belgium, the newest Haskel technology was unveiled. Haskel Product Engineer Pooya Mahmoudian presented on prevention methods for H2 embrittlement in pressure vessels and discussed an entirely new industry technology that has the potential to dramatically impact prices for companies developing hydrogen refueling stations.
Review Mahmoudian's presentation to learn more about Haskel's new technology and the advancements we're making in hydrogen technology.
JMeter webinar - integration with InfluxDB and GrafanaRTTS
Watch this recorded webinar about real-time monitoring of application performance. See how to integrate Apache JMeter, the open-source leader in performance testing, with InfluxDB, the open-source time-series database, and Grafana, the open-source analytics and visualization application.
In this webinar, we will review the benefits of leveraging InfluxDB and Grafana when executing load tests and demonstrate how these tools are used to visualize performance metrics.
Length: 30 minutes
Session Overview
-------------------------------------------
During this webinar, we will cover the following topics while demonstrating the integrations of JMeter, InfluxDB and Grafana:
- What out-of-the-box solutions are available for real-time monitoring JMeter tests?
- What are the benefits of integrating InfluxDB and Grafana into the load testing stack?
- Which features are provided by Grafana?
- Demonstration of InfluxDB and Grafana using a practice web application
To view the webinar recording, go to:
https://www.rttsweb.com/jmeter-integration-webinar
The Art of the Pitch: WordPress Relationships and SalesLaura Byrne
Clients don’t know what they don’t know. What web solutions are right for them? How does WordPress come into the picture? How do you make sure you understand scope and timeline? What do you do if sometime changes?
All these questions and more will be explored as we talk about matching clients’ needs with what your agency offers without pulling teeth or pulling your hair out. Practical tips, and strategies for successful relationship building that leads to closing the deal.
Securing your Kubernetes cluster_ a step-by-step guide to success !KatiaHIMEUR1
Today, after several years of existence, an extremely active community and an ultra-dynamic ecosystem, Kubernetes has established itself as the de facto standard in container orchestration. Thanks to a wide range of managed services, it has never been so easy to set up a ready-to-use Kubernetes cluster.
However, this ease of use means that the subject of security in Kubernetes is often left for later, or even neglected. This exposes companies to significant risks.
In this talk, I'll show you step-by-step how to secure your Kubernetes cluster for greater peace of mind and reliability.
Kubernetes & AI - Beauty and the Beast !?! @KCD Istanbul 2024Tobias Schneck
As AI technology is pushing into IT I was wondering myself, as an “infrastructure container kubernetes guy”, how get this fancy AI technology get managed from an infrastructure operational view? Is it possible to apply our lovely cloud native principals as well? What benefit’s both technologies could bring to each other?
Let me take this questions and provide you a short journey through existing deployment models and use cases for AI software. On practical examples, we discuss what cloud/on-premise strategy we may need for applying it to our own infrastructure to get it to work from an enterprise perspective. I want to give an overview about infrastructure requirements and technologies, what could be beneficial or limiting your AI use cases in an enterprise environment. An interactive Demo will give you some insides, what approaches I got already working for real.
State of ICS and IoT Cyber Threat Landscape Report 2024 previewPrayukth K V
The IoT and OT threat landscape report has been prepared by the Threat Research Team at Sectrio using data from Sectrio, cyber threat intelligence farming facilities spread across over 85 cities around the world. In addition, Sectrio also runs AI-based advanced threat and payload engagement facilities that serve as sinks to attract and engage sophisticated threat actors, and newer malware including new variants and latent threats that are at an earlier stage of development.
The latest edition of the OT/ICS and IoT security Threat Landscape Report 2024 also covers:
State of global ICS asset and network exposure
Sectoral targets and attacks as well as the cost of ransom
Global APT activity, AI usage, actor and tactic profiles, and implications
Rise in volumes of AI-powered cyberattacks
Major cyber events in 2024
Malware and malicious payload trends
Cyberattack types and targets
Vulnerability exploit attempts on CVEs
Attacks on counties – USA
Expansion of bot farms – how, where, and why
In-depth analysis of the cyber threat landscape across North America, South America, Europe, APAC, and the Middle East
Why are attacks on smart factories rising?
Cyber risk predictions
Axis of attacks – Europe
Systemic attacks in the Middle East
Download the full report from here:
https://sectrio.com/resources/ot-threat-landscape-reports/sectrio-releases-ot-ics-and-iot-security-threat-landscape-report-2024/
LF Energy Webinar: Electrical Grid Modelling and Simulation Through PowSyBl -...DanBrown980551
Do you want to learn how to model and simulate an electrical network from scratch in under an hour?
Then welcome to this PowSyBl workshop, hosted by Rte, the French Transmission System Operator (TSO)!
During the webinar, you will discover the PowSyBl ecosystem as well as handle and study an electrical network through an interactive Python notebook.
PowSyBl is an open source project hosted by LF Energy, which offers a comprehensive set of features for electrical grid modelling and simulation. Among other advanced features, PowSyBl provides:
- A fully editable and extendable library for grid component modelling;
- Visualization tools to display your network;
- Grid simulation tools, such as power flows, security analyses (with or without remedial actions) and sensitivity analyses;
The framework is mostly written in Java, with a Python binding so that Python developers can access PowSyBl functionalities as well.
What you will learn during the webinar:
- For beginners: discover PowSyBl's functionalities through a quick general presentation and the notebook, without needing any expert coding skills;
- For advanced developers: master the skills to efficiently apply PowSyBl functionalities to your real-world scenarios.
Generating a custom Ruby SDK for your web service or Rails API using Smithyg2nightmarescribd
Have you ever wanted a Ruby client API to communicate with your web service? Smithy is a protocol-agnostic language for defining services and SDKs. Smithy Ruby is an implementation of Smithy that generates a Ruby SDK using a Smithy model. In this talk, we will explore Smithy and Smithy Ruby to learn how to generate custom feature-rich SDKs that can communicate with any web service, such as a Rails JSON API.
Encryption in Microsoft 365 - ExpertsLive Netherlands 2024Albert Hoitingh
In this session I delve into the encryption technology used in Microsoft 365 and Microsoft Purview. Including the concepts of Customer Key and Double Key Encryption.
UiPath Test Automation using UiPath Test Suite series, part 4DianaGray10
Welcome to UiPath Test Automation using UiPath Test Suite series part 4. In this session, we will cover Test Manager overview along with SAP heatmap.
The UiPath Test Manager overview with SAP heatmap webinar offers a concise yet comprehensive exploration of the role of a Test Manager within SAP environments, coupled with the utilization of heatmaps for effective testing strategies.
Participants will gain insights into the responsibilities, challenges, and best practices associated with test management in SAP projects. Additionally, the webinar delves into the significance of heatmaps as a visual aid for identifying testing priorities, areas of risk, and resource allocation within SAP landscapes. Through this session, attendees can expect to enhance their understanding of test management principles while learning practical approaches to optimize testing processes in SAP environments using heatmap visualization techniques
What will you get from this session?
1. Insights into SAP testing best practices
2. Heatmap utilization for testing
3. Optimization of testing processes
4. Demo
Topics covered:
Execution from the test manager
Orchestrator execution result
Defect reporting
SAP heatmap example with demo
Speaker:
Deepak Rai, Automation Practice Lead, Boundaryless Group and UiPath MVP
Epistemic Interaction - tuning interfaces to provide information for AI supportAlan Dix
Paper presented at SYNERGY workshop at AVI 2024, Genoa, Italy. 3rd June 2024
https://alandix.com/academic/papers/synergy2024-epistemic/
As machine learning integrates deeper into human-computer interactions, the concept of epistemic interaction emerges, aiming to refine these interactions to enhance system adaptability. This approach encourages minor, intentional adjustments in user behaviour to enrich the data available for system learning. This paper introduces epistemic interaction within the context of human-system communication, illustrating how deliberate interaction design can improve system understanding and adaptation. Through concrete examples, we demonstrate the potential of epistemic interaction to significantly advance human-computer interaction by leveraging intuitive human communication strategies to inform system design and functionality, offering a novel pathway for enriching user-system engagements.
From Siloed Products to Connected Ecosystem: Building a Sustainable and Scala...
Assessing the design effect of pressure vessel height and radius on reactor stability and safety
1. Control Theory and Informatics
ISSN 2224-5774 (Paper) ISSN 2225-0492 (Online)
Vol.4, No.1, 2014
www.iiste.org
Assessing the Design effect of Pressure Vessel Height and Radius
on Reactor Stability and Safety
A.I. Oludare1, M.N. Agu,2 A.M. Umar,3 S.O. Adedayo4, O. E. Omolara5 and L.N. Okafor6
1
Nigerian Defence Academy, Department of Physics, Kaduna
2
Nigeria Atomic Energy Commission, Abuja
3
Energy Commission of Nigeria, Department of Nuclear Science & Technology, Abuja
4
National Open University of Nigeria, Department of Information Technology, Abuja
5
Ahmadu Bello University, Department of Mathematics, Zaria, Nigeria
6
Nigerian Defence Academy, Department of Mathematics and Computer Science, Kaduna
Corresponding author:
email: isaac_abiodun@yahoo.com
ABSTRACT
The Design of Reactor Pressure Vessel (RPV) should be that the height of pressure vessel is up to 16.0m and
radius is up to 5.6m to ensure safe operation of nuclear reactor. The research conducted safety margin test on the
design dimension of RPV in terms of the height and radius, secondly safety margin test was carried out on
applied high temperature on the reactor graphite core and thirdly, safety margin test were perform on the cooling
problem of the nuclear reactor core in relation to fuel temperature. By applying Linear Regression Analysis
Techniques on some typical Reactor Pressure Vessel (RPV) models. The results of the statistical analysis on
these types of nuclear reactor models reveals that the RPV models promises stability under application of
pressure vessel up to 16.0m height and radius 5.6m. At this point the temperature seems at maximum and the
reactor agrees to be more stable as the regression plot was optimized, that is the least squares method finds its
optimum when the sum, S, of squared residuals is at minimum. The safety margin prediction of 3.1% was
validated for a typical RPV model as an advantage over the current 5.1% challenging problem for plant
engineers to predict the safety margin limit.
Keywords: Reactor pressure vessel design, height and radius, high temperature effect, fuel element, risk and
failure, reactor safety, safety factor, Ỳ, optimization, stability margin, reactor pressure vessel design models,
selection of pressure vessel.
INTRODUCTION
The main drivers for reactor development are:
• Improved safety (for example by the incorporation of passive safety features)
• Reduced capital cost
• Reduced operating cost
• Improved efficiency and utilization
• Improved design effectiveness
• Reduced build-time
• Minimize the risk of failure
These main drivers shall provide a good, novel approach and method for multi-objective decision-making in the
development of the nuclear industry.
The reactor pressure vessels are designed with great care to ensure safe operation when used within their prescribed temperature and pressure limits. The selection of pressure vessel must be the one which has the
capability, pressure rating, corrosion resistance and design features that are suitable for its intended use. When
pressure vessel could not function as to supply water or gas in cooling the reactor the phenomena can cause
hydrogen built-up within the reactor and this can eventually melt down the reactor core, as in the case studies of
nuclear accident in Japan when the pressure vessel fail to function, heat continue to built-up in the reactor and
the reactor meltdown and was damaged [1]. Then Seawater was being pumped into the reactor in an attempt to
cool down the radioactive core. Also, there was a recorded explosion which occurred, at the NDK Crystal
manufacturing company in Belvidere, Illinois resulted from Stress Corrosion Cracking of High-Pressure Vessel
[2], and fatal accident at Goodyear Tire and Rubber Plant in Houston, Texas, following Pressure Vessel Codes,
the accident occurred, when an overpressure in a heat exchanger led to a violent rupture of the exchanger [3].
There was a safety concern because counterfeit reactor equipment of the reactor pressure vessel at Koodankulam
Nuclear Power Plant in the Tirunelveli district of the southern Indian state of Tamil Nadu [4]. Since these also
include safety grade equipment, there is also a potential for accident.
19
2. Control Theory and Informatics
ISSN 2224-5774 (Paper) ISSN 2225-0492 (Online)
Vol.4, No.1, 2014
www.iiste.org
In exercising the responsibility for the selection of pressure equipment, the prospective user is often faced with a
choice between over or under-designed equipment. The hazards introduced by under-designed pressure vessels
are readily apparent, but the penalties that must be paid for over-designed apparatus are often overlooked[5].
The list of available nominal chemical composition of pressure vessel construction materials are highlighted in
Table 1:
Table I: Highlighted the nominal chemical composition of pressure vessel materials
Major Elements (Percent)
Material
Typical Trade Name Fe
Ni
Cr
Mo Mn
T316/316 L
65
12
17
2.5 2.0
Stainless Steel
Alloy 20
Carpenter 20
35
34
20
2.5 2.0
Alloy 400
Monel 400
1.2
66
Alloy 600
Inconel 600
8
76
15.5
Alloy B-2
Hastelloy B-2
2
66
1
28
1
Alloy C-276
Hastelloy C-276
6.5
53
15.5
16
1
Nickel 200
99
Titanium
Commercially pure titanium
Ti 99
Grade 2
min
Titanium
Commercially pure titanium
Ti 99
Grade 2
min
Titanium
99
Grade 7
Zirconium
Zr + Hf 99.2 min, Hf 4.5 max
Grade 702
Zirconium
Zr + Hf 99.2 min, Hf 4.5 max
Grade 705
Other
Si 1.0
Cu 3.5, Cb 1.0 max
Cu 31.5
Co 1.0
W4.0, Co 2.5
0.15 Pd
Nb 2.5
A pressure vessel is a closed, rigid container designed to hold gases or liquids at a pressure different from the
ambient pressure.
In addition to industrial compressed air receivers and domestic hot water storage tanks, other examples of
pressure vessels are: diving cylinder, recompression chamber, distillation towers, autoclaves and many other
vessels in mining or oil refineries and petrochemical plants, nuclear reactor vessel, habitat of a space ship,
habitat of a submarine, pneumatic reservoir, hydraulic reservoir under pressure, rail vehicle airbrake reservoir,
road vehicle airbrake reservoir and storage vessels for liquified gases such as ammonia, chlorine, propane,
butane and LPG.
DESIGN AND OPERATION STANDARDS
In the nuclear industrial sector, pressure vessels are designed to operate safely at a specific pressure and
temperature, technically referred to as the "Design Pressure" and "Design Temperature". The pressure vessel is
designed to a pressure, there is typically a safety valve or relief valve to ensure that this pressure is not exceeded
in operation. A vessel that is inadequately designed to handle a high pressure constitutes a very significant safety
hazard. Because of that, the design and certification of pressure vessels is governed by design codes such as the
ASME Boiler and Pressure Vessel Code in North America[6], the Pressure Equipment Directive of the EU
(PED), Japanese Industrial Standard (JIS), CSA B51 in Canada, AS1210 in Australia and other international
standards like Lloyd's, Germanischer Lloyd, Det Norske Veritas, Stoomwezen and so on.
SHAPE OF A PRESSURE VESSEL
Theoretically a sphere would be the optimal shape of a pressure vessel. Most pressure vessels are made of steel.
To manufacture a spherical pressure vessel, forged parts would have to be welded together. Some mechanical
properties of steel are increased by forging, but welding can sometimes reduce these desirable properties. In case
of welding, in order to make the pressure vessel meet international safety standards, carefully selected steel with
a high impact resistance are be used. Most pressure vessels are arranged from a pipe and two covers.
Disadvantage of these vessels is the fact that larger diameters make them relatively more expensive, so that for
example the most economic shape of a 1000 litres, 250 bar (25,000 kPa) pressure vessel might be a diameter of
450 mm and a length of 6500 mm.
20
3. Control Theory and Informatics
ISSN 2224-5774 (Paper) ISSN 2225-0492 (Online)
Vol.4, No.1, 2014
www.iiste.org
No matter what shape it takes, the minimum mass of a pressure vessel scales with the pressure and volume it
contains. For a sphere, the mass of a pressure vessel is
,…………………………………………Equation (1)
Where:
M is mass
p is the pressure difference from ambient- the gauge pressure
V is volume
ρ is the density of the pressure vessel material
σ is the maximum working stress that material can tolerate.
Other shapes besides a sphere have constants larger than 3/2 (infinite cylinders take 2), although some tanks,
such as non-spherical wound composite tanks can approach this.
CYLINDRICAL VESSEL WITH HEMISPHERICAL ENDS
This is sometimes called a "bullet" for its shape, although in geometric terms it is a capsule.
For a cylinder with hemispherical ends,
,……………………………Equation (2)
where
• R is the radius, W is the middle cylinder width only, and the overall width is W + 2R
CYLINDRICAL VESSEL WITH SEMI-ELLIPTICAL ENDS
In a vessel with an aspect ratio of middle cylinder width to radius of 2:1,
.…………………………………………Equation (3)
GAS STORAGE
In looking at the first equation, the factor PV, in SI units, is in units of (pressurization) energy. For a stored gas,
PV is proportional to the mass of gas at a given temperature, thus
. ………………………………………Equation (4)
The other factors are constant for a given vessel shape and material. So we can see that there is no theoretical
"efficiency of scale", in terms of the ratio of pressure vessel mass to pressurization energy, or of pressure vessel
mass to stored gas mass. For storing gases, "tankage efficiency" is independent of pressure, at least for the same
temperature.
So, for example, a typical design for a minimum mass tank to hold helium (as a pressurant gas) on a rocket
would use a spherical chamber for a minimum shape constant, carbon fiber for best possible
cold helium for best possible
.
, and very
STRESS IN THIN-WALLED PRESSURE VESSELS
Stress in a shallow-walled pressure vessel in the shape of a sphere is
,………………………………….Equation (5)
where
is hoop stress, or stress in the circumferential direction,
is stress in the longitudinal direction, p
is internal gauge pressure, r is the inner radius of the sphere, and t is thickness of the cylinder wall. A vessel can
21
4. Control Theory and Informatics
ISSN 2224-5774 (Paper) ISSN 2225-0492 (Online)
Vol.4, No.1, 2014
www.iiste.org
be considered "shallow-walled" if the diameter is at least 10 times (sometimes cited as 20 times) greater than the
wall depth.
Stress in a shallow-walled pressure vessel in the shape of a cylinder is
,……………………………………………..Equation (6)
,…………………………………………Equation (7)
is hoop stress, or stress in the circumferential direction,
is stress in the longitudinal direction, p
where
is internal gauge pressure, r is the inner radius of the cylinder, and t is thickness of the cylinder wall.
Almost all pressure vessel design standards contain variations of these two formulas with additional empirical
terms to account for wall thickness tolerances, quality control of welds and in-service corrosion allowances.
For example, the ASME Boiler and Pressure Vessel Code (BPVC) (UG-27) formulas are:
Spherical shells:
…………………….Equation (8)
Cylindrical shells:
………………………………Equation (9)
………………………….Equation (10)
Where, E is the joint efficient, and all others variables as stated above.
The factor of safety is often included in these formulas as well, in the case of the ASME BPVC this term is
included in the material stress value when solving for Pressure or Thickness.
LINEAR EXPANSION
To a first approximation, the change in length measurements of an object ("linear dimension" as opposed to, e.g.,
volumetric dimension) due to thermal expansion is related to temperature change by a "linear expansion
coefficient". It is the fractional change in length per degree of temperature change. Assuming negligible effect of
pressure, we may write:
αL = (
)………………………………………………Equation (11)
where L is a particular length measurement and
is the rate of change of that linear dimension per unit change
in temperature.
The change in the linear dimension can be estimated to be:
Δ = αLΔT………………………………………………..Equation.(12)
This equation works well as long as the linear-expansion coefficient does not change much over the change in
temperature ΔT. If it does, the equation must be integrated.
EFFECTS ON STRAIN
For solid materials with a significant length, like rods or cables, an estimate of the amount of thermal expansion
can be described by the material strain, given by and defined as:
εthermal = (Lfinal – Linitial)/Linitial…………………….. Equation.(13)
22
5. Control Theory and Informatics
ISSN 2224-5774 (Paper) ISSN 2225-0492 (Online)
Vol.4, No.1, 2014
www.iiste.org
where Linitial is the length before the change of temperature and Lfinal is the length after the change of
temperature.
For most solids, thermal expansion is proportional to the change in temperature:
εthermal
ΔT…………………………………………… Equation (14)
Thus, the change in either the strain or temperature can be estimated by:
Εthermal = αL ΔT………………………………………. Equation (15)
Where, ΔT = (Tfinal – Tinitial) ………………………….Equation (16)
is the difference of the temperature between the two recorded strains, measured in degrees Celsius or Kelvin, and
αL is the linear coefficient of thermal expansion in "per degree Celcius" or "per Kelvin", denoted by °C−1 or K−1,
respectively.
AREA EXPANSION
The area thermal expansion coefficient relates the change in a material's area dimensions to a change in
temperature. It is the fractional change in area per degree of temperature change. Ignoring pressure, we may
write:
αA =
(
)………………………………………………Equation.(17)
where A is some area of interest on the object, and
is the rate of change of that area per unit change in
temperature.
The change in the linear dimension can be estimated as:
Δ = αAΔT………………………………………………Equation (18)
This equation works well as long as the linear expansion coefficient does not change much over the change in
temperature δT. If it does, the equation must be integrated.
VOLUMETRIC EXPANSION
For a solid, we can ignore the effects of pressure on the material, and the volumetric thermal expansion
coefficient can be written:
αV =
(
)………………………………………………Equation (19)
where V is the volume of the material, and
is the rate of change of that volume with temperature.
This means that the volume of a material changes by some fixed fractional amount. For example, a steel block
with a volume of 1 cubic meter might expand to 1.002 cubic meters when the temperature is raised by 50 °C.
This is an expansion of 0.2 %. If we had a block of steel with a volume of 2 cubic meters, then under the same
conditions, it would expand to 2.004 cubic meters, again an expansion of 0.2 %. The volumetric expansion
coefficient would be 0.2 % for 50 K, or 0.004 %/K.
If we already know the expansion coefficient, then we can calculate the change in volume
Δ = αVΔT……………………………………… Equation.(20)
Where, Δ is the fractional change in volume (e.g., 0.002) and ΔT is the change in temperature (50° C).
The above example assumes that the expansion coefficient did not change as the temperature changed. This is
not always true, but for small changes in temperature, it is a good approximation. If the volumetric expansion
coefficient does change appreciably with temperature, then the above equation will have to be integrated:
Δ =
where To is the starting temperature and
temperature T.
…………………… Equation (21)
is the volumetric expansion coefficient as a function of
23
6. Control Theory and Informatics
ISSN 2224-5774 (Paper) ISSN 2225-0492 (Online)
Vol.4, No.1, 2014
www.iiste.org
The temperature of the fuel varies as a function of the distance from the center to the rim. At distance d from the
center the temperature (Td) is described by the equation where ρ is the power density (W m−3) and Kf is the
thermal conductivity.
Td = TRim + ρ (rpellet² – d²) (4 Kf)−1……………………Equation.(22)
When the nuclear fuel increases in temperature, the rapid motion of the atoms in the fuel causes an effect known
as Doppler broadening. When thermal motion causes a particle to move towards the observer, the emitted
radiation will be shifted to a higher frequency. Likewise, when the emitter moves away, the frequency will be
lowered. For non-relativistic thermal velocities, the Doppler shift in frequency will be:
………………………………………. Equation (23)
where is the observed frequency,
is the rest frequency, is the velocity of the emitter towards the
observer, and is the speed of light.
Since there is a distribution of speeds both toward and away from the observer in any volume element of the
radiating body, the net effect will be to broaden the observed line.
If
is the fraction of particles with velocity component
the corresponding distribution of the frequencies is
to
along a line of sight, then
,…………………………. ..Equation (24)
where
…………………………………….Equation (25)
is the velocity towards the observer corresponding to the shift of the rest frequency
to
.
Therefore,
.
…… Equation (26)
We can also express the broadening in terms of the wavelength . Recalling that in the
non-relativistic limit
, we obtain
.
…Equation (27)
In the case of the thermal Doppler broadening, the velocity distribution is given by the Maxwell distribution
,……… ..Equation (28)
where,
is the mass of the emitting particle,
is the temperature and
is the Boltzmann constant.
Then,
,… Equation (29)
24
7. Control Theory and Informatics
ISSN 2224-5774 (Paper) ISSN 2225-0492 (Online)
Vol.4, No.1, 2014
www.iiste.org
We can simplify this expression as
,……...Equation (30)
which we immediately recognize as a Gaussian profile with the standard deviation
,…………………………………………… …..Equation.(31)
and full width at half maximum (FWHM)
.
,………………… …..Equation.(32)
The fuel then sees a wider range of relative neutron speeds. Uranium-238, which forms the bulk of the uranium
in the reactor, is much more likely to absorb fast or epithermal neutrons at higher temperatures. This reduces the
number of neutrons available to cause fission, and reduces the power of the reactor. Doppler broadening
therefore creates a negative feedback because as fuel temperature increases, reactor power decreases. All
reactors have reactivity feedback mechanisms, except some gas reactor such as pebble-bed reactor which is
designed so that this effect is very strong and does not depend on any kind of machinery or moving parts.
FAILURE AND ACCIDENT ANALYSIS
Several reports on the safety of pressure vessel design these include “Reactor Pressure Vessel Task of Light
Water Reactor Sustainability Program,”[7] “Prevention of Catastrophic Failure in Pressure Vessels and
Pipings,”[8] “Pressurized Thermal Shock Potential at Palisades,”[9], “Stress Analysis & Pressure Vessels,”[10]
“AS 1200 Pressure Vessels”[11] and "Stress Analysis & Pressure Vessels”[12].
These accidents may perhaps be as a result of design concept process of some of these reactors (which could
involve novel technologies) that have inherent risk of failure in operation and were not well studied/understood.
In avoiding such accidents the industry has been very successful. As in over 14,500 cumulative reactor-years of
commercial operation in 32 countries, there have been only three major accidents to nuclear power plants –
Fukushima, Chernobyl and Three Mile Island. As in other industries, the design and operation of nuclear power
plants aims to reduce the likelihood of accidents, and avoid major human consequences when they occur.
However, recent study of the reactor fuel under accident conditions, reveal that after subjecting the fuel to
extreme temperatures — far greater temperatures than it would experience during normal operation or postulated
accident conditions — TRISO fuel is even more robust than expected. Specifically, the research revealed that at
1,800 degrees Celsius (more than 200 degrees Celsius greater than postulated accident conditions) most fission
products remained inside the fuel particles, which each boast their own primary containment system [8].
METHODOLOGY
In this work, Ordinary Least Square (OLS) methodology, which is largely used in nuclear industry for modeling
safety, is employed. Some related previous works on the application of regression analysis technique include:
“Statistical Analysis of Reactor Pressure Vessel Fluence Calculation Benchmark Data Using Multiple
Regression Techniques”[13], “Simplified modeling of a PWR reactor pressure vessel lower head failure in the
case of a severe accident”[14]. Others are, “Analyses of loads on reactor pressure vessel internals in a
pressurized water reactor due to a loss-of-coolant accident considering fluid-structure interaction”[15],
“Regression analysis of gross domestic product and its factors in Lithuania,”[16] and “Investigating the Effect of
Loss-of-Pressure-Control on the Stability of Water-Cooled Reactor Design Models,”[17].
25
8. Control Theory and Informatics
ISSN 2224-5774 (Paper) ISSN 2225-0492 (Online)
Vol.4, No.1, 2014
www.iiste.org
THE RESEARCH OBJECTIVES
To apply the linear regression technique on reactor pressure vessel design models for the determination of their
safety margin that is to examine the effect of pressure vessel height and radius on the stability and safety of the
nuclear reactor during operation.
THE RESEARCH MOTIVATION
The purpose of this work is to assist countries wishing to include nuclear energy for the generation of electricity,
like Nigeria, to secure a reactor that is better and safe. Also, the studies intended to provide guidance in
developing practical catalytic materials for power generation reactor and to help researchers make appropriate
recommendation for Nigeria nuclear energy proposition as one of the solutions to Nigeria energy crisis.
Moreover, the study is to provide a good, novel approach and method for multi-objective decision-making based
on six dissimilar objectives attributes: evolving technology, effectiveness, efficiency, cost, safety and failure.
Furthermore, this is to help Nigeria meet its international obligations to use nuclear technology for peaceful
means. Finally, the achievement is to make worldwide contribution to knowledge.
RESEARCH DESIGN/APPROACH
Theory and experiment have shown that for some reactor, the design of pressure vessel plays significant role in
the safety of the reactor during operation in preventing overheating of the reactor and reactor meltdown during
accident. Hence, in this work, a statistical analysis of a design input parameter of a typical reactor pressure vessel
was investigated for safety. More specifically, the studies concentrated on technical factors that limit the
achievement of higher burn-up of fuel in various design of reactor pressure vessels, such as the pressure height
and radius mechanical interaction. Furthermore, the study examined the temperature of the fuel behaviour under
reactor accident conditions are also included.
The research approach involves adjusting the parameters of a model function to best fit a data set. A simple data
, i = 1, ..., n, where
is an independent variable and
is a
set consists of n points (data pairs)
dependent variable whose value is found by observation. The model function has the form f (x,β), where the m
adjustable parameters are held in the vector . The goal is to find the parameter values for the model which
"best" fits the data. The least squares method finds its optimum when the sum, S, of squared residuals
is a minimum…………………………………………………………(25)
Table 2: Input data for safety margin against pressure vessel height and pressure vessel
diameter in a typical graphite moderated reactor design model. Source : [18]
Nos. of trial (j)
Pressure vessel height (m)
Pressure vessel radius (m)
1
2
3
4
5
6
7
8
9
10
4
8
12
16
20
24
28
32
34
36
5
5.1
5.2
5.6
5.9
6.3
6.6
6.8
7.5
7.9
26
9. Control Theory and Informatics
ISSN 2224-5774 (Paper) ISSN 2225-0492 (Online)
Vol.4, No.1, 2014
www.iiste.org
RESULTS AND ANALYSES
1. Pressure Vessel Design (PVD)
The results of the application of the linear regression analysis of the data in Table 6 of a typical Pressure Vessel
Design (PVD) models are presented as follows:
(i)
Empirical Expression for Safety Factor, Ỳ
In assessing the effect of pressure vessel height and radius on the Stability and Safety of the nuclear reactor
during operation, the data obtained in Table 6 which represents a typical parameter for Pressure Vessel Design
(PVD) models was used in order to obtain the best fit for the model. The new conceptual fuel design for reactor
operation could optimize the performance of the water-cooled reactor.
The linear regression model equation to be solved is given by:
Ỳ = B0 + B1Xj+ ej ………………………………………… Equation (33)
where,
B0 is an intercept, B1 is the slope, Xj is the rate of increase in fuel volume
ej = error or residual, j = 1,2,3,…,k and k is the last term.
Empirical Expression for Safety Factor, Ỳ for Normal Pressure Reading
The model empirical expression is the equation of the straight line relating heat in the reactor and the volume of
fuel in the reactor as a measure of safety factor estimated as:
Ỳ = (4.3231) + (0.0872)*(Xj) + ej
……
- the equation (34) is the estimated model or predicted
where,
Ỳ = Dependent Variable, Intercept = 4.3231,
Slope = 0.0872, X = Independent Variable,
e = error or residual, j = 1,2,3,…,10 and 10 is the last term of trial.
The Figure 1 shows the linear regression plot section
(ii) Linear regression plot section
27
Equation (34)
10. Control Theory and Informatics
ISSN 2224-5774 (Paper) ISSN 2225-0492 (Online)
Vol.4, No.1, 2014
www.iiste.org
Pressure Vessel Radius (m)
8.0
7.1
(Ỳ)
6.3
5.4
4.5
0.0
10.0
20.0
30.0
Pressure Vessel Height (m)
Figure 1: pressure vessel height and radius design
(iii)
F-test Result
Table 3: Summary of F-test Statistical Data
Parameter
Dependent Variable
Independent Variable
Intercept(B0)
Slope(B1)
R-Squared
Correlation
Mean Square Error (MSE)
Coefficient of Variation
Value
Ỳ (Decay heat or temperature)
X (fuel volume)
4.3231
0.0872
0.9392
0.9691
6.999824 x 10-2
0.0427
Square Root of MSE
0.2645718
Table 4: Descriptive Statistics Section
Parameter
Dependent
Variable
Heat (0c)
Count
10
Mean
6.1900
Standard Deviation
1.0115
Minimum
5.0000
Maximum
7.9000
Independent
Fuel (g)
10
21.4000
11.2368
4.0000
36.0000
28
(X)
40.0
11. Control Theory and Informatics
ISSN 2224-5774 (Paper) ISSN 2225-0492 (Online)
Vol.4, No.1, 2014
www.iiste.org
The Table 5 is the regression estimation section results that show the least-squares estimates of the intercept and
slope followed by the corresponding standard errors, confidence intervals, and hypothesis tests. These results are
based on several assumptions that are validated before they are used.
Table 5: Regression Estimation Section
Parameter
Intercept B(0)
Slope B(1)
Regression Coefficients
4.3231
0.0872
Lower 95% Confidence Limit
3.8904
0.0691
Upper 95% Confidence Limit
4.7558
0.1053
Standard Error
0.1876
0.0078
Standardized Coefficient
0.0000
0.9691
T-Value
23.0392
11.1158
Prob Level (T-Test)
0.0000
0.0000
Reject H0 (Alpha = 0.0500)
Power (Alpha = 0.0500)
Regression of Y on X
Inverse Regression from X on Y
Orthogonal Regression of Y and X
Yes
1.0000
4.3231
4.2022
4.3221
Yes
1.0000
0.0872
0.0929
0.0873
In Table 6 the analysis of variance shows that the F-Ratio testing whether the slope is zero, the degrees of
freedom, and the mean square error. The mean square error, which estimates the variance of the residuals, was
used extensively in the calculation of hypothesis tests and confidence intervals.
Table 6: Analysis of Variance Section
Source
DF
Intercept
Slope
Error
Adj. Total
Total
1
1
8
9
10
Sum of
Squares
383.161
8.649014
0.5599859
9.209
392.37
Mean Squares
F-Ratio
8.649014
383.161
8.649014
6.999824X10-2
1.023222
Prob Level
Power(5%)
123.5605
1.0000
S = Square Root(6.999824X10-2) = 0.2645718
In Table 7 Anderson Darling method confirms the rejection of H0 at 20% level of significance but all of the
above methods agreed that H0 Should not be rejected at 5% level of significance. Hence the normality
assumption is satisfied as one of the assumptions of the Linear Regression Analysis is that the variance of the
error variable δ2 has to be constant.
Table 7: Tests of Assumptions Section
Assumption/Test Residuals
follow Normal Distribution?
Shapiro Wilk
Anderson Darling
D'Agostino Skewness
D'Agostino Kurtosis
D'Agostino Omnibus
Constant Residual Variance?
Modified Levene Test
Relationship is a Straight Line?
Lack of Linear Fit F(0, 0) Test
Test
Value
Prob Level
0.8901
0.5842
1.0600
-0.5545
1.4310
0.169812
0.128324
0.289166
0.579233
0.488954
Is the Assumption
Reasonable at the 20% or
0.2000 Level of
Significance?
No
No
Yes
Yes
Yes
0.3515
0.569628
Yes
0.0000
0.000000
No
Notes:
A 'Yes' means there is not enough evidence to make this assumption seem unreasonable.
A 'No' means that the assumption is not reasonable
29
12. Control Theory and Informatics
ISSN 2224-5774 (Paper) ISSN 2225-0492 (Online)
Vol.4, No.1, 2014
(iv)
www.iiste.org
Residual Plots Section
The plot section is used as further check on the validity of the model to satisfy all the assumptions of the linear
regression analysis.
Amir D. Aczel (2002, P528) have stated that the normality assumption can be checked by the use of plot of
errors against the predicted values of the dependent variable against each of the independent variable and against
time (the order of selection of the data points) and on a probability scale.
The diagnostic plot for linear regression analysis is a scatter plot of the prediction errors or residuals against
predicted values and is used to decide whether there is any problem in the data at hand Siegel F (2002, p.578).
The Figure 2 is for the plot of errors against the order to selection of the data points (e = 1,2,…,12). Although
the order of selection was not used as a variable in the mode, the plot reveal whether order of selection of the
data points should have been included as one of the variables in our regression model. This plot shows no
particular pattern in the error as the period increases or decreases and the residuals appear to be randomly
distributed about their mean zero, indicating independence. The residuals are randomly distributed with no
pattern and with equal variance as volume of fuel increases.
Residuals of Heat oc
Note:
1. Residual = original value for heat (Y) minors predicted value for heat, Ỳ
2. Count = the design number (design 1, 2, 3, …, 12 )
0.6
0.4
0.1
-0.2
-0.4
0.0
10.0
20.0
30.0
40.0
Fuel Volume in Mass (g)
Figure 2: Residuals of Heat (0C) versus Fuel (g)
Figure 3 shows the histogram of residuals of error (et ) and this is nearly
skewed to the right but the software used indicated that the plot is normal.
30
13. Control Theory and Informatics
ISSN 2224-5774 (Paper) ISSN 2225-0492 (Online)
Vol.4, No.1, 2014
www.iiste.org
8.0
6.0
Count
4.0
2.0
0.0
-0.4
-0.2
0.1
0.4
0.6
0
Residuals of Heat ( C)
Figure 3: Histogram of Residuals of Heat (0C)
While Figure 4 is the result on plot graph of experimental errors. The residuals are perfectly normally distributed
as most of the error terms align themselves along the diagonal straight line with some error terms outside the arc
above and below the diagonal line. This further indicates that the estimated model is valid.
Residuals of Heat oc
0.6
0.4
0.1
-0.2
-0.4
-2.0
-1.0
0.0
Expected Normals
1.0
2.0
Figure 4: Normal Probability Plot of Residuals of Heat (0C)
2. SUMMARY/CONCLUSION
In conclusion the research conducting safety margin test on the design dimension of graphite core of graphite
moderated reactor in terms of the height and diameter, secondly safety margin test was carried out on applied
high temperature on the reactor graphite core and thirdly, safety margin test were perform on the cooling
problem of the nuclear reactor core in relation to fuel temperature. By applying Linear Regression Analysis
Techniques on some typical Pressure Vessel Design (PVD) models. The results of the statistical analysis on
these types of nuclear reactor models reveals that the PVD models promises stability under application of
pressure vessel up to 16m height and radius 5.6m. At this point the temperature seems at maximum and the
reactor agrees to be more stable as the regression plot was optimized, that is the least squares method finds its
optimum when the sum, S, of squared residuals
31
14. Control Theory and Informatics
ISSN 2224-5774 (Paper) ISSN 2225-0492 (Online)
Vol.4, No.1, 2014
www.iiste.org
is a minimum at the given dimension of PV height 16.0metre and radius 5.6metre.
Meanwhile, at anything below height of 16metre and radius of 5.6metre the fuel element seems to be unstable in
the reactor as the regression plot could not find it optimal.
The research implication is that the design dimension of graphite moderated reactor core could be significant to
the nuclear fuel temperature and safety of the reactor during operation or accident. Secondly, the safety margin
prediction of up to 3.1% has been validated for reactor design models on water-cooled reactor regarding the
design dimension of graphite moderated reactor core parameter, core temperature and fuel temperature. The
research effort served as an advantage over the current 5.1% challenging problem for plant engineers to predict
the safety margin limit. According to Xianxun Yuan (2007, P49) in “Stochastic Modeling of Deterioration in
Nuclear Power Plants Components” a challenging problem of plant engineers is to predict the end of life of a
system safety margin up to 5.1% validation.
The current design limits for various reactors safety in a nuclear power plant, defined by the relative increase and
decrease in the parametric range at a chosen operating point from its original value, varies from station to station.
However, the finding in the work would suggest that the design of the plant should ensure that operating reactor
core are made up of large graphite core in order to minimize core melting in an extreme high temperature
condition which can damaged the reactor.
The Design of Reactor Pressure Vessel (RPV) should be that the height of pressure vessel is up to 16.0m and
radius is up to 5.6m are maintained in their construction and possibly provision for extra pressure vessel in the
design to ensure safe operation of nuclear reactor. But the final responsibility for selecting a reactor or pressure
vessel that will perform to the user’s satisfaction in any particular reaction or test must rest with the user.
If pressure vessels technology solution must be addressed properly then the following areas of applicable
pressure technology needs to be well study these include dynamic and seismic analysis; equipment qualification;
fabrication; fatigue and fracture prediction; finite and boundary element methods; fluid-structure interaction;
high pressure engineering; elevated temperature analysis and design; inelastic analysis; life extension; lifeline
earthquake engineering; PVP materials and their property databases; NDE; safety and reliability; and verification
and qualification of analysis with relevant software.
Finally, the discoveries on high temperature effect on graphite moderated reactor safety either in terms of design
graphite dimension parameter or fuel temperature on the power reactor stability and safety factor should provide
a new method for reactor design conceptualization. This shall also provide a good, novel approach and method
for multi-objective decision-making based on six dissimilar objectives attributes: evolving technology,
effectiveness, efficiency, cost, safety and failure. The implication of this research effort to Nigeria’s nuclear
power project drive.
It is therefore recommended that for countries wishing to include nuclear energy for the generation of electricity,
like Nigeria, the design input parameters of the selected nuclear reactor should undergo test and analysis using
this method for optimization and choice.
Acknowledgments
We thank Department of Physics, Nigerian Defence Academy (NDA) Kaduna, Nigeria Atomic Energy
Commission (NAEC), Energy Commission of Nigeria (ECN), National Open University of Nigeria (NOUN),
Department of Science and Information Technology and Department of Mathematics, Ahmadu Bello University
(ABU) Zaria, Nigeria, for the human and material support during the research work.
References
[1] Yanko Yanev (2013). Nuclear Accidents Learning the Lessons. Atoms for Peace. NEM School Tokai Mura,
Japan.
[2] Occupational Safety and Health Branch Labour Department 2008, “Brief Accident Cases of Boilers and
Pressure Vessels” in Hong Kong. Edition June 2008. Washington DC, 2011, “A U.S. Chemical Safety Board
(CSB) case study. Release at the Goodyear Tire and Rubber Company in Houston, Texas, January 27, 2011.
[3] U.S.NRC, 2012.Resolution of Generic Safety Issues: Task CH6: Graphite-Moderated Reactors Updated
March 29, 2012.
32
15. Control Theory and Informatics
ISSN 2224-5774 (Paper) ISSN 2225-0492 (Online)
Vol.4, No.1, 2014
www.iiste.org
[4] VT Padmanabhan et al., 2013, “Counterfeit/obsolete Equipment and Nuclear Safety issues of VVER-1000
Reactors at Kudankulam, India” European Committee for Radiation Risks (ECRR)- India Desk,
P.O.Pathayakkunnu, Tellicherry, Kerala, India
[5] Stirred Reactors and Pressure Vessels. Parr Instrument Company 211 Fifty-third Street Moline, Illinois
61265 USA. Available at: <http:www.parrinst.com>
[6] An International Code 2007, “ASME Boiler & Pressure Vessel Code” The Americal Society of Mechanical
Engineers. 2007.
[7] R.K. Nanstad 2011, “Reactor Pressure Vessel Task of Light Water Reactor” Sustainability Program:
Milestone Report on Materials and Machining of Specimens for the ATR-2 Experiment. R.K. Nanstad, Oak
Ridge National Laboratory and G. R. Odette, University of California, Santa Barbara
[8] Rauno Rintamaa, KimWallin, Kari Ikonen, Kari Torronen, Heli Talja, Heikki Keinånen, Arja Saarenheimo,
Fred Nilsson, Matt i Sarkimo, Stig Wåstberg, Christian Debel, 1989 “Prevention of Catastrophic Failure in
Pressure Vessels
and Pipings” Final Report of the NKA-Project MAT 570. The Swedish Nuclear Power Inspectorate Library
P.O.Box 27106 S-102 52 Stockholm Sweden. 1989.
[9] Michael J. Keegan 2005 “Pressurized Thermal Shock Potential at Palisades”
Coalition for a Nuclear Free Great Lakes (July 8, 1993, Rekeyed August 3, 2005)
[10] Clemens Kaminski “Stress Analysis & Pressure Vessels” Lent Term 2005. Available at:
<http://www.cheng.cam.ac.uk/research/groups/laser/>
[11] SAI Global 2011,“AS 1200 Pressure Vessels" Retrieved 14 November 2011
[12] John F. Carew, et al., 2003 “Statistical Analysis of Reactor Pressure Vessel Fluence Calculation Benchmark
Data Using Multiple Regression Techniques” Nuclear Science and Engineering / Volume 143 / Number 2 /
Pages 158-163 February 2003
[13] V. Koundy, et al., 2005. “Simplified modeling of a PWR reactor pressure vessel lower head failure in the
case of a severe accident” Nuclear Engineering and Design Volume 235, Issue 8, April 2005, Pages 835–843.
[14] P. Akimov and L. Obereisenbuchner (2010) “Analyses of loads on reactor pressure vessel internals in a
pressurized water reactor due to a loss-of-coolant accident considering fluid-structure interaction” Kerntechnik:
Vol. 75, No. 6, pp. 311-315. AREVA NP GmbH, Paul-Gossen-Str. 100, 91052 Erlangen, Germany.
[15] Viktorija Bobinaite, et al. (2001),“Regression analysis of gross domestic product and its factors in
Lithuania” Kaunas University of Technology, Lithuania Published by ISSN 1822-6515 economics and
management: 2011.
[16] Recent research (Oludare A.I., et al. 2013). Investigating the Effect of Loss-of-Pressure-Control on the
Stability of Water-Cooled Reactor Design Models. International Journal of Energy and Environmental Research
Vol.1, No.1, pp.1-15, September 2013, (Online) 7(5): 5-17 DOI: 10.5923/j.jnpp.20130303.01 Published by
European and American Journals September 2013 United Kingdom.
[17] M. Raghed, 2011. Chernobyl Accident [pdf]
[18] Amir D. Aczel (2012). Entanglement: The Greatest Mystery in Physics. Published on October 1, 2012.
Available at: <http://www.AudioBookMix.com>
[19] Andrew F. Siegel 2012 “Practical Business Statistics” Publication: New Delhi Elsevier 2012 . 619 Date:
2012.
33
16. This academic article was published by The International Institute for Science,
Technology and Education (IISTE). The IISTE is a pioneer in the Open Access
Publishing service based in the U.S. and Europe. The aim of the institute is
Accelerating Global Knowledge Sharing.
More information about the publisher can be found in the IISTE’s homepage:
http://www.iiste.org
CALL FOR JOURNAL PAPERS
The IISTE is currently hosting more than 30 peer-reviewed academic journals and
collaborating with academic institutions around the world. There’s no deadline for
submission. Prospective authors of IISTE journals can find the submission
instruction on the following page: http://www.iiste.org/journals/
The IISTE
editorial team promises to the review and publish all the qualified submissions in a
fast manner. All the journals articles are available online to the readers all over the
world without financial, legal, or technical barriers other than those inseparable from
gaining access to the internet itself. Printed version of the journals is also available
upon request of readers and authors.
MORE RESOURCES
Book publication information: http://www.iiste.org/book/
Recent conferences: http://www.iiste.org/conference/
IISTE Knowledge Sharing Partners
EBSCO, Index Copernicus, Ulrich's Periodicals Directory, JournalTOCS, PKP Open
Archives Harvester, Bielefeld Academic Search Engine, Elektronische
Zeitschriftenbibliothek EZB, Open J-Gate, OCLC WorldCat, Universe Digtial
Library , NewJour, Google Scholar