This document provides information on gas turbine engines. It discusses the basic components and operation of turbine engines including the air inlet, compressor, combustion chambers, turbine section, and exhaust section. It describes the advantages of turbine engines over piston engines. The document then goes into more detail about different types of compressors and turbines used in gas turbine engines as well as the physics principles that apply to how they work. It provides diagrams and explanations of open and closed gas turbine cycles, different engine types such as turbojet, turboprop and turbofan, and components like fans, spools, and ducting.
The gas turbine is an internal combustion engine that uses air as the working fluid. The engine extracts chemical energy from fuel and converts it to mechanical energy using the gaseous energy of the working fluid (air) to drive the engine and propeller, which, in turn, propel the aeroplane.
This Presentation gives a brief idea on turbojet engines, their components, working principle and also on the materials used in both the hot and cold sections of the engine, applications, etc..
The gas turbine is an internal combustion engine that uses air as the working fluid. The engine extracts chemical energy from fuel and converts it to mechanical energy using the gaseous energy of the working fluid (air) to drive the engine and propeller, which, in turn, propel the airplane.
Jet Propulsion: Recap, Intake, Types of compressor, and MoreJess Peters
Jet Propulsion: Recap, Intake, Types of compressor: Axial flow compressor and Centrifugal flow compressor.
After Burners
Air distribution in the Combustion Chamber.
Reverse Thrust
RAMJET is a type of jet engine in which the air drawn in for combustion is compressed solely by the forward motion of the aircraft.
A ramjet uses this high pressure in front of the engine to force air through the tube, where it is heated by combusting some of it with fuel.
It is then passed through a nozzle to accelerate it to supersonic speeds. This acceleration gives the ramjet forward thrust.
A gas turbine, also called a combustion turbine, is a type of internal combustion engine. It has an upstream rotating compressor coupled toa downstream turbine, and a combustion chamber in-between. Energy is added to the gas stream in the combustor, where fuel is mixed with air and ignited. In the high-pressure environment of the combustor, combustion of the fuel increases the temperature. The products of the combustion are forced into the turbine section
Visit https://www.topicsforseminar.com to Download
A presentation taking the student through how a Jet Engine works, and the different types of Jet Engine available. Initially written to prepare Air Cadets for their Jet Engine exam.
The gas turbine is an internal combustion engine that uses air as the working fluid. The engine extracts chemical energy from fuel and converts it to mechanical energy using the gaseous energy of the working fluid (air) to drive the engine and propeller, which, in turn, propel the aeroplane.
This Presentation gives a brief idea on turbojet engines, their components, working principle and also on the materials used in both the hot and cold sections of the engine, applications, etc..
The gas turbine is an internal combustion engine that uses air as the working fluid. The engine extracts chemical energy from fuel and converts it to mechanical energy using the gaseous energy of the working fluid (air) to drive the engine and propeller, which, in turn, propel the airplane.
Jet Propulsion: Recap, Intake, Types of compressor, and MoreJess Peters
Jet Propulsion: Recap, Intake, Types of compressor: Axial flow compressor and Centrifugal flow compressor.
After Burners
Air distribution in the Combustion Chamber.
Reverse Thrust
RAMJET is a type of jet engine in which the air drawn in for combustion is compressed solely by the forward motion of the aircraft.
A ramjet uses this high pressure in front of the engine to force air through the tube, where it is heated by combusting some of it with fuel.
It is then passed through a nozzle to accelerate it to supersonic speeds. This acceleration gives the ramjet forward thrust.
A gas turbine, also called a combustion turbine, is a type of internal combustion engine. It has an upstream rotating compressor coupled toa downstream turbine, and a combustion chamber in-between. Energy is added to the gas stream in the combustor, where fuel is mixed with air and ignited. In the high-pressure environment of the combustor, combustion of the fuel increases the temperature. The products of the combustion are forced into the turbine section
Visit https://www.topicsforseminar.com to Download
A presentation taking the student through how a Jet Engine works, and the different types of Jet Engine available. Initially written to prepare Air Cadets for their Jet Engine exam.
ATENÇÃO LIDERANÇAS<<<
Link liberado para pré cadastro:
FAÇA JÁ SEU CADASTRO E SEJA PIONEIRO NESSE NEGÓCIO ESPETACULAR!!!!!!!
http://clubedelideres.net/?afiliado=fotografia
VEJAM AS VANTAGENS DE FAZER PARTE DO CDL
CLUBE DE LIDERES: Você obterá por só R$ 25,00.
• Sistema de Gerenciamento de Rede com direito de revenda e 100% de lucro!
• Ganhos rápidos de ciclos na matriz 2x2 (mesmo só com derramamentos)
• Residual mensal na matriz global 2x10 – meta da primeira fase R$ 6.963,00
• Premiações na matriz 2x7 conforme for atingindo os níveis sendo eles:
1º nível: página de captura
2º nível: auto responder
3º nível: site personalizado
4º nível: adesão na primeira empresa de mmn
5º nível: adesão na segunda empresa de mmn
6º nível: adesão na terceira empresa de mmn
7º nível: adesão na quarta empresa de mmn
• E muito mais novidades chegando por ai!
assista ao vídeo https://www.youtube.com/watch?v=ShXwyFNikVE
Seja um vencedor!
FAÇA JÁ SEU CADASTRO E ATIVE SUA CONTA
http://clubedelideres.net/?afiliado=fotografia
jrfotografia.desner@outlook.com
VAMOS QUE VAMOS PARA O SUCESSO!!!
Onze catalogus compacte schaarheftafels aan u gepresenteerd in het Duits, Intraboss is importeur voor de BeNeLux van Gruse schaarheftafels, U kunt bij ons terecht voor schaarheftafels op maat in elke prijsklasse en standaard uitvoeringen, onze schaarheftafels worden geleverd met CE en worden gebouwd volgens de EN 1570-1 norm
Brayton or Joule cycle -P-V diagram and thermal efficiency. Construction and working of gas turbine i] Open cycle ii] Closed cycle gas turbine, simple circuit, Comparison, P-V & T-S diagramTurbojet and Turboprop Engine and Application
Preparing for EASA Mod.15 Gas turbine engines . Then avoid reading lengthy books here are my personal short notes and explanations and important topics for Mod.15
INTRODUTION OF AIRCRAFT PROPULSION-new.pptxrahul325730
This is an topic which related to aeronautical and aerospace field
This topic will help you to go through propulsion in an aircrafts engine and rocket engine
#propulsion#aeronautics
This so called PPT for propulsion study for Shenyang Aerospace University. This PPT right protected by Dr. divinder K. Yadav. Its using in SAU by Lale. For all students of Aeronautical Engineering must memorize each & every words from this PPT. If you miss a single words you must fail in the Exam. Remember there is no chance to be creative or use sense you just need to use the power of memorizing.
This so called PPT for propulsion study for Shenyang Aerospace University. This PPT right protected by Dr. divinder K. Yadav. Its using in SAU by Lale. For all students of Aeronautical Engineering must memorize each & every words from this PPT. If you miss a single words you must fail in the Exam. Remember there is no chance to be creative or use sense you just need to use the power of memorizing.
This so called PPT for propulsion study for Shenyang Aerospace University. This PPT right protected by Dr. divinder K. Yadav. Its using in SAU by Lale. For all students of Aeronautical Engineering must memorize each & every words from this PPT. If you miss a single words you must fail in the Exam. Remember there is no chance to be creative or use sense you just need to use the power of memorizing.
This so called PPT for propulsion study for Shenyang Aerospace University. This PPT right protected by Dr. divinder K. Yadav. Its using in SAU by Lale. For all students of Aeronautical Engineering must memorize each & every words from this PPT. If you miss a single words you must fail in the Exam. Remember there is no chance to be creative or use sense you just need to use the power of memorizing.
This so called PPT for propulsion study for Shenyang Aerospace University. This PPT right protected by Dr. divinder K. Yadav. Its using in SAU by Lale. For all students of Aeronautical Engineering must memorize each & every words from this PPT. If you miss a single words you must fail in the Exam. Remember there is no chance to be creative or use sense you just need to use the power of memorizing.
This so called PPT for propulsion study for Shenyang Aerospace University. This PPT right protected by Dr. divinder K. Yadav. Its using in SAU by Lale. For all students of Aeronautical Engineering must memorize each & every words from this PPT. If you miss a single words you must fail in the Exam. Remember there is no chance to be creative or use sense you just need to use the power of memorizing.
This so called PPT for propulsion study for Shenyang Aerospace University. This PPT right protected by Dr. divinder K. Yadav. Its using in SAU by Lale. For all students of Aeronautical Engineering must memorize each & every words from this PPT. If you miss a single words you must fail in the Exam. Remember there is no chance to be creative or use sense you just need to use the power of memorizing.
This so called PPT for propulsion study for Shenyang Aerospace University. This PPT right protected by Dr. divinder K. Yadav. Its using in SAU by Lale. For all students of Aeronautical Engineering must memorize each & every words from this PPT. If you miss a single words you must fail in the Exam. Remember there is no chance to be creative or use sense you just need to use the power of memorizing.
More from Affiliated Corporation To Help the International Students of Shenyang Aerospace University (8)
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
6. Basic Gas Turbines Engines
The turbine engine produces thrust by increasing the
velocity of the air flowing through the engine. It
consists of:
• air inlet,
• compressor,
• combustion chambers,
• turbine section,
• exhaust section,
• accessory section.
6
12. Physics applicable to jet engines
•Newton’s Third Law of Motion
•Charles’ First Gas Law
•Charles’ Second Gas Law
•Pascal’s Law
•Bernoulli’s Theorem
•First Law of Thermodynamics
•Second Law of Thermodynamics
12
13. For every action there is an equal and
opposite reaction
• Turbine engines are known as reaction
engine
Newton’s Third Law of Motion
13
18. Charles’ Second Gas Law
• When the volume of a gas is held
constant, the pressure of the gas will
increase as it’s temperature is increased
18
19. Pascal’s Law
• Pressure always acts at right angles to
any confining surface, undiminished
throughout the fluid regardless of shape
and size of the container
19
21. • The sum of all energies in a perfect fluid
must remain constant
• If kinetic energy increases then potential
energy must decrease, ie:- velocity is
inversely proportional to pressure
Bernoulli’s Theorem
21
34. Force (F) = ma = (weight ÷ gravity) × acceleration
Thrust (T) = ma + (pressure × area)
T =
Where,
Wa - weight of air
V1 – velocity of airplane
V2 – velocity of air at jet nozzle
Wf – weight of fuel
Aj – area of jet nozzle
Pj – static pressure of jet nozzle
Pam – ambient static pressure
The Jet Engine Equation
Pam)Aj(PjVf
g
Wf
V1)(V2
g
Wa
34
36. • A common method of determining engine
thrust
• EPR is the ratio between the total
pressure in the exhaust duct and the total
pressure at the inlet to the engine
Engine Pressure Ratio (EPR)
36
37. A larger EPR = more thrust
Typical EPR values (Boeing 727):
NB. EPR is only useful as a measure of
thrust on those engines with fixed area
exhaust nozzles 37
38. Thrust versus horsepower
• Recall: power = rate of doing work
• in other words:
– Lift up a one pound weight through 550 feet in one
second and you have 1 horsepower
• Mathematically:
– Power = Force x Distance
Time
• Propeller torque and RPM are used to
calculate horsepower
38
39. Thrust versus horsepower
• Power harder to measure in a jet engine (time
and distance elements not always involved)
• Once a jet engine is moving forward then a
comparison can be made
• At an airspeed of 375 mph (325 kts), one lb of
thrust = 1 HP
• THP = thrust x TAS (kts)
325
• So a B777 engine produces 90,000lbs of thrust
– On take off (100kts) = 27690 HP
– During climb (300kts) = 83070 HP (assuming full power)
39
46. 46
Turbojet engines
Also called as the pure jet.
The compressor section passes inlet air at a high rate of
speed to the combustion chamber.
The combustion chamber contains the fuel inlet and igniters
for combustion. The expanding air drives a turbine, which is
connected by a shaft to the compressor, sustaining engine
operation.
The accelerated exhaust gases from the engine provide
thrust.
Turbojet engines are limited on range and endurance. They
are also slow to respond to throttle applications at slow
compressor speeds.
47. 47
Turboprop engines
A turboprop engine is a turbine engine that drives a
propeller through a reduction gear. The exhaust gases
drive a power turbine connected by a shaft that drives the
reduction gear assembly.
Turboprop engines are most efficient at speeds between
250 and 400 m.p.h. and altitudes between 18,000 and
30,000 feet. They also perform well at the slow airspeeds
required for takeoff and landing, and are fuel efficient. The
48. 48
Turbofan engines
Turbofan engines are designed to create additional thrust by diverting a
secondary airflow around the combustion chamber.
The turbofan bypass air generates increased thrust, cools the engine, and
aids in exhaust noise suppression. This provides turbojet-type cruise
speed and lower fuel consumption.
The inlet air that passes through a turbofan engine is usually divided into
two separate streams of air. One stream passes through the engine core,
while a second stream bypasses the engine core. It is this bypass stream
of air that is responsible for the term “bypass engine.” A turbofan’s bypass
ratio refers to the ratio of the mass airflow that passes through the fan
divided by the mass airflow that passes through the engine core.
49. 49
Turboshaft engines
It delivers power to a shaft that drives something other than
a propeller.
The biggest difference between a turbojet and turboshaft
engine is that on a turboshaft engine, most of the energy
produced by the expanding gases is used to drive a turbine
rather than produce thrust.
Many helicopters use a turboshaft gas turbine engine. In
addition, turboshaft engines are widely used as auxiliary
power units on large aircraft.
60. Fan Bypass Ratio
It is the ratio of airflow through the fan
duct to the airflow through the engine
core
For example, if a turbofan has a bypass
ratio of 6 to 1, 7 units of air are entering
the intake duct with 1 unit entering the
engine core and 6 units going through the
fan section only
60
63. Propulsive Efficiency
Thrust (force) = mass x acceleration
A turbojet gives a large acceleration to a
small mass of air
A turboprop gives a small acceleration to a
large mass of air
63
65. • The turbofan has replaced the turbojet for
commercially operated aircraft
• For a turbojet and turbofan of the same
rated thrust the turbofan will burn less fuel
• The turbofan has less wasted kinetic
energy after exiting the exhaust (exhaust
velocity is closer to aircraft speed)
Propulsive Efficiency
65
75. Turbine Engine Entrance Ducts
Properties
Must furnish a uniform supply of air to the
compressor in all conditions
Contributes to stall-free compressor
performance
Must create minimal drag
4
77. Gas Turbine Entrance Ducts
A divergent duct from front to back
Increased static pressure
to the compressor
Designed to be efficient at the cruise but
must still operate effectively when the
aircraft is stationary and before RAM
pressure recovery occurs
6
83. Inlet Guide Vanes
Direct intake duct air onto the first
compressor stage rotor at the correct
angle of attack
Both stationary and variable angle inlet
guide vanes may be used
12
85. Compressor Section
It’s function is to supply air in sufficient
quantity to satisfy the needs of the
combustor
Compressors operate on the principle of
acceleration of air followed by diffusion to
convert the acquired kinetic energy into a
pressure rise
14
86. Compressor Section
A secondary purpose of the compressor
section is to supply bleed air for use by
the engine and aircraft systems
Common bleed air uses are
Cabin pressurisation
Air Conditioning
Aircraft pneumatic systems
Anti icing, inflating door seals, suction
15
89. The principal differences between the two types of impellers are
size and ducting arrangement.
The double-entry type has a smaller diameter but is usually
operated at a higher rotational speed to ensure enough airflow.
The single-entry impeller permits convenient ducting directly to
the impeller eye (inducer vanes) as opposed to the more
complicated ducting necessary to reach the rear side of the
double-entry type.
Plenum Chamber
This chamber is necessary for a double-entry compressor because
air must enter the engine at almost right angles to the engine axis.
To give a positive flow, air must surround the engine compressor at
a positive pressure before entering the compressor.
Single & double entry impellers
18
93. Centrifugal Compressor
Air enters the impeller at the hub and then
flows outward through impeller blades
The impeller imparts rotational and
outward velocity to the air which then
flows into the diffuser where divergent
ducts convert velocity into pressure
22
111. Axial Compressor
The air flows axially through a number of
rotating rotor blades and fixed
intervening stator vanes
Each set of rotating blades and stator vanes
is known as a compressor stage
40
116. Axial compressor roots and tips
Vibration is a problem with any rotational
machinery
The root of the compressor disk is often
only loosely fitted to the hub
As the compressor rotates centrifugal
loading locks the blade in its correct position
and the air stream over the airfoil provides a
shock mounting or cushioning effect
45
117. To avoid energy losses (including shock
waves) over the tips of the rotor blades,
the clearance between the rotor and the
surrounding shroud must be kept to a
minimum
Newer engines are designed to rotate within
a shroud strip of abradable material
Sometimes during coastdown a high
pitched noise can be heard if the blade
tip and shroud strip are touching
46
118. Advantages of Axial Flow Compressors
Higher compression available by
addition of compression stages
Small frontal area and lower drag
47
119. Disadvantages of Axial Compressors
High cost of manufacture
Relatively high weight
Higher starting power requirements
Lower pressure rise per stage
Good compression in the cruise and
take off power settings only 48
123. Multi Spool Compressors
For any given power setting the high
pressure compressor speed is held
constant by the fuel control unit
The low pressure compressor(s) will speed
up and slow down with changes in engine
inlet conditions resulting from atmospheric
changes
52
125. Advantages of multi-spool axial
compressors
Less power required for starting
Less prone to compressor stalling
Quicker acceleration
54
126. Compressor Stall & Surge
Compressor blades, being aerofoils, can
stall at too high an angle of attack
the close proximity of blades in different
stages means that if one stage stalls, so
may the next
55
127. Angle of Attack and compressor stall
Compressor stalls cause air flowing
through the compressor to slow down,
stagnate or reverse direction
this is then know as an engine surge
Any change to the design airflow will have
an effect to all other sections of the gas
turbine engine
56
131. Angle of Attack and compressor stall
Causes
Excessive fuel flow changes
Turbulent air
Contaminated or damaged compressors
Contaminated or damaged turbine blades
Engine operation outside design RPM
Too rapid movement of throttles
60
132. Angle of Attack and compressor stall
Can occur during a cross wind take-off
Can occur during a steep turn
Detected by
Audible noise and/or vibration
Fluctuating RPM
Increased EGT
61
133. Angle of Attack and compressor stall
Reverse air flow may result in the compressor
blades bending and contacting the stator
vanes
Sophisticated engines use:
bleed air to reduce the possibility of
compressor stall, or
variable incidence guide vanes
62
137. The Combustion Section
The combustion process must ideally be
able to efficiently convert chemical energy
to heat energy under all operating
situations from engine start to engine shut
down
A chemically correct (stoichiometric)
mixture is approximately 15:1 air/fuel
3
138. The Combustion Process
The temperature of the gases released by
combustion can be well in excess of 15000C
which will destroy the combustion chamber
and turbine section
About 60% of the air entering the
combustion chamber is used for cooling only
4
141. The Combustion Process
To function properly the combustion
chamber must
1. Provide a proper environment for the
mix of air and fuel
2. Cool the hot gases to a temperature
the turbine section components can
withstand
To accomplish this the airflow through
the combustor is divided into primary
and secondary paths 7
142. The Combustion Process
Air from the compressor may enter
the combustion chamber in excess of
500 feet per second (300 knots)
The axial flow of the primary airflow
must be reduced to about 5 feet per
second (3 knots)
Because of the slow flame propagation
rate of jet fuels if the primary velocity
were too high it would blow the flame
out (flame out) 8
143. The Combustion Process
The reduction in axial velocity is achieved
by swirl vanes which create radial motion
and retard axial motion
The air from the swirl vanes and secondary
air holes interact and create a region of low
velocity circulation
This forms a toroidal vortex similar to a
smoke ring stabilising and anchoring the
flame 9
146. The Combustion Process
The combustion process is complete in
the first one third of the combustion
liner
In the remaining two thirds of the
combustor length the combusted and
uncombusted gas is mixed to provide an
even heat distribution at the turbine
nozzle
12
147. Flame Out
Although uncommon in modern engines
they still occur
Some common causes are
Turbulent weather
High altitude
Violent flight maneuvers
13
149. Flame Out
Flame out (lean) Usually occurs at low
fuel pressures at low engine speeds in
high altitude flight
Flame out (rich) Usually occurs during
fast engine acceleration in which an over
rich mixture causes combustion pressure
to increase until compressor flow stagnates
Turbulent inlet conditions can also cause stalls15
150. Flame Out
To minimise the possibility of flame out it
is essential to have a correct matching of
compression ratio, mass airflow and engine
speed
16
151. Combustion Chamber Types
The various combustion chambers in
use include
Multiple can
Can Annular
Annular reverse flow
Annular
17
153. Multiple Can
This type of combustion chamber is more
common with centrifugal flow
compressors and earlier types of axial
flow compressors
The separate flame tubes are
interconnected to allow a constant
pressure and also propagate
combustion around the flame tubes
during starting 19
159. Fuel Supply
Fuel is supplied to the combustion chamber
by one of two methods
The most common is the injection of a
fine atomised spray into the re-circulating
airstream through spray nozzles
25
161. Fuel Supply
The second fuel supply method is based on
the pre-vaporisation of the fuel before it
enters the combustion zone
The fuel/air mix is carried in a vaporising
tube which passes through the primary
flame area of the combustion chamber
More common in low power engines
27
162. The Turbine Section
The turbine section is bolted onto the
combuster and contains nozzle guide vanes,
turbine rotors and turbine stators
The turbine functions to transform a
portion of the kinetic and heat energy in
the exhaust gases into mechanical work to
drive the compressor, propeller, fan and
accessories
28
165. The turbine section
• Since energy is extracted from the airflow
through a turbine section, pressure decreases
across the turbine section
• Hence the boundary layer is much more likely
to remain attached than in the compressor
section
• Each stage of the turbine section can support
several stages of compressor
31
178. Reaction turbine blades
Reaction drives the blades via an
aerodynamic reaction
The gas stream is accelerated by
convergent nozzle guide vanes and directed
to flow over the turbine blades producing
an aerodynamic reaction
44
179. Impulse turbine blades
Impulse turbine blades rotate via impact
of high velocity gas on the blades
The blades of a pure impulse turbine are
bucket shaped to maximise the conversion
of kinetic energy to mechanical energy
45
181. Turbine Blades
Most turbine blades combine both
impulse and reaction principles
The degree of reaction depends on the
type of engine
47
182. Turbine Blades
Turbojets require high exhaust velocities
to produce thrust so they use high reaction
turbine blades to produce maximum
acceleration
Turboprops and APUs use impulse turbine
blades because they are concerned with
power extraction and not thrust
48
183. Turbine Blades
Turbofans use reaction/impulse blades to
extract energy to drive the fan while
maintaining reasonably high exhaust
velocity for core engine thrust
49
184. Turbine Blades
• Higher entry
pressure at the blade
tips means that, to
create a uniform
exit flow, blade
profiles are adjusted
to a reaction profile
at the tip
50
186. Turbine Blade Creep
Turbine blades are subject to enormous
stress loads
A blade weighing only 8 grams may
have to resist a centrifugal force of over
2000 kg
This causes turbine blades to lengthen with
continued use – known as creep
52
189. Turbine Blade Creep
If manufacturer’s temperature or rpm
limits are exceeded the creep rate increases
and blade life is drastically reduced
Overhauls are timed to ensure that blades
are replaced before tertiary creep begins
55
190. Turbine Temperature Measurement
Ideally temperature probes should be placed
in the turbine inlet to measure turbine inlet
temperature (TIT)
The temperature at the turbine inlet is
usually too hot to place temperature probes
56
191. Turbine Temperature Measurement
Temperature probes are usually placed in an
intermediate stage (ITT) or at the turbine
outlet stage (TOT)
ITT and TOT readings are often
compensated to give an indication of the
temperature at the most critical point – the
turbine inlet
57
193. Exhaust Section
The exhaust section is located behind the
turbine section and usually consists of a
convergent cone to convert pressure
energy to kinetic energy
59
206. Accessory Section
The primary function is to provide space for the
mounting of accessories necessary for operation
and control of the engine. It also includes
accessories concerned with the aircraft, such as
electric generators and fluid power pumps.
Secondary functions include acting as an oil
reservoir and/or oil sump, and housing the
accessory drive gears and reduction gears.
Accessories are usually mounted on common
pads either ahead of or adjacent to the
compressor section. 72
215. Auxiliary Power Units
A gas turbine powerplant
Supplies the aircraft with
Bleed air
Electrical power
Hydraulic power
81
216. Auxiliary Power Units
Used mainly during ground operations,
take-off and landing
Most can be used in flight as a back up
supply source but usually have an
operating altitude limit
82
217. Auxiliary Power Units
APUs have the following features:
Operate at a constant RPM
Start sequence is fully automatic
Vital parameters are automatically
monitored
Automatic shutdown with any faults
83
218. Auxiliary Power Units
A typical cockpit panel consists of:
Start and stop button
Turbine temperature indicator (EGT)
RPM indicator
Control switches for bleed air,
hydraulic and electrical generation
84
220. Many turbofan engines have two or more spools to
A. improve the cooling of the combustion chamber
walls resulting in a lower turbine temperature
B. assist the compressor sections to rotate closer to
their ideal RPM
C. reduce vibration within the engine core
D. increase spool up time required when compared
to a single spool
And….. the answer is………..
86
221. An ideal jet intake delivers air to the compressor
in which state?
A. No turbulence and pressure lower than ambient
B. Increased radial velocity and temperature higher
than ambient
C. Increased temperature and velocity compared
ambient conditions
D. No turbulence and pressure higher than ambient
And….. the answer is………..
87
222. The row of stator blades after each row of
compressor blades in n axial flow compressor is
designed to
A. longitudinally balance the engine
B. convert axial flow to radial flow before the next
rotating compressor section
C. convert kinetic energy to pressure energy
D. Convert pressure energy to pressure energy
And….. the answer is………..
88
223. Of a turbofan’s total air passing through the
intake 21% goes through the engine core. The
bypass ratio is closest to
A. 4:1
B. 5:1
C. 1:5
D. 1:4
And….. the answer is………..
89
224. Which of the following would increase the
maximum possible performance of a jet engine?
A. introduce the air into the engine at a lower speed
B. introduce the air into the engine at a lower
temperature
C. introduce the air into the engine at a higher
temperature
D. introduce the air into the engine at a lower
pressure
And….. the answer is………..
90
225. Gas decreases in velocity and increases in pressure
when
A. flowing through a convergent duct
B. it is within the last two thirds of the combustion
chamber
C. it is within the nozzle guide vanes prior to the first
turbine rotor section
D. flowing through a divergent duct
And….. the answer is………..
91
226. What is meant by tertiary creep in a turbine blade
of a gas turbine engine?
A. blade creep experienced on the test bench by the
manufacturer
B. normal blade creep during the acceptable working
life of the turbine blade section
C. blade creep that could be detrimental to
continued use of the turbine section
D. an unruly university aviation student
And….. the answer is………..
92
227. For a given engine RPM, thrust output from a gas
turbine engine will be greatest
A. At MSL in ISA conditions
B. At high altitude in ISA conditions
C. At high altitude in ISA + conditions
D. At MSL in ISA + conditions
And….. the answer is………..
93