This document discusses statistical process control (SPC). It defines SPC and explains that its goal is to monitor processes and ensure they operate at their full potential to produce conforming products. There are two types of variation in processes: natural/common cause variation and special cause variation. The document then defines several key SPC terms and describes tools used in SPC like control charts. It provides examples of measuring equipment used for SPC and outlines the methodology for applying SPC to a CNC machine process.
QUALITY IMPROVEMENTS USING STATISTICAL PROCESS CONTROL
Using this method the assignable causes for rejections were found out and therefore there was no rejection to very less rejection of the products which was controlled using SPC.
Temperature Controller is one of the important components of every industry and equipment where temperature maintenance, control and monitoring are needed.
QUALITY IMPROVEMENTS USING STATISTICAL PROCESS CONTROL
Using this method the assignable causes for rejections were found out and therefore there was no rejection to very less rejection of the products which was controlled using SPC.
Temperature Controller is one of the important components of every industry and equipment where temperature maintenance, control and monitoring are needed.
Weiber's air volume meter is ideal equipment for easurement of quantity of air flowing through a tube and its actual speed in a given time duration. For More Information Please Logon http://goo.gl/kcAynz
Basics of Automation in Solid Dosage Form Production (Formulation & Developem...Vishal Shelke
Basics of Automation in Solid Dosage Form Production by Mr. Vishal Shelke(Formulation & Developement M.Pharm Sem II)
https://youtube.com/vishalshelke99
https://instagram.com/vishal_stagram
Sub :- Formulation & Developement
M.Pharm Sem II
Savitribai Phule Pune University
Calibration and validation ,difference , ph meter and weigh balance calibrati...Divy Patel
Calibration and validation , ph meter and weigh balance calibration SOPs procedure with difference and frequency of doing this hope this will be helpful for you... also comment if needed
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Weiber's air volume meter is ideal equipment for easurement of quantity of air flowing through a tube and its actual speed in a given time duration. For More Information Please Logon http://goo.gl/kcAynz
Basics of Automation in Solid Dosage Form Production (Formulation & Developem...Vishal Shelke
Basics of Automation in Solid Dosage Form Production by Mr. Vishal Shelke(Formulation & Developement M.Pharm Sem II)
https://youtube.com/vishalshelke99
https://instagram.com/vishal_stagram
Sub :- Formulation & Developement
M.Pharm Sem II
Savitribai Phule Pune University
Calibration and validation ,difference , ph meter and weigh balance calibrati...Divy Patel
Calibration and validation , ph meter and weigh balance calibration SOPs procedure with difference and frequency of doing this hope this will be helpful for you... also comment if needed
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Abstract The deployment of statistical process control (SPC) in manufacturing environments is a prominent global phenomenon. Statistical Process Control is largely used in industries for monitoring the process parameters. It is a standard method for visualizing and controlling processes on the basis of measurements of randomly selected samples. The decisions about what needs to be improved, the possible methods to improve it, and the steps to take after getting results from the charts are all made by humans and based on wisdom and experience. The statistical process control described in this paper gives the details about the SPC, its advantages and limitation, applications and information regarding the control charts. Keywords: Statistical Process Control, Control chart, 5M’s, Capability Indices.
Adaptive-optimal control involves re-identification of the machining process and the model obtained is used to calculate the optimal process parameters.
Optimal control characterizes the addiction of the technical and economic indicators to process parameters. Characteristic for performance technical indicators is that their dependence to parameter values of process has a limitative, what leads to one of the following conclusions, appropriately or inappropriately, and therefore can serve as restrictions in optimization problem.
Economic indicators have a continuous dependence of process parameters and therefore they are used as objective functions.
This presentation is all about my working experience at iljin electronics pvt ltd. and its all about the working of IQC department of electronics industry.
" Microprocessor control offers improved accuracy , efficiency and versatility because of its high speed reasons , programmability and computational ability. "
2. STATISTICAL PROCESS CONTROL:-
• It is the application of statistical methods to monitor and
control a process to ensure that it operates at its full
potential to produce conforming product.
OR
• it is an analytical decision making tool which allow you to
see when process is working correctly and when it is not.
• variation present in any process, deciding when variation
is natural and when it need correction is the key to quality
control.
3. TYPES OF VARIATION
Two kinds of variation occur in all manufacturing process.
1. Natural or common cause variation:-
It includes variations in temperature, properties of raw
material etc.
2. Special cause variation:-
With sufficient investigation, a specific cause, such as
abnormal raw material or incorrect set-up parameters,
can be found for special cause variation.
4. TERMS IN SPC
Process
Stable Process
Control Chart
Feed Rate
Cycle Time
Materials
Control plan
5. PROCESS
A process is a step by step activity which is use to transform
raw material into finish products.
It contains many steps.
Measuring of each parts
If variation occurs
Different process
6. STABLE PROCESS
Run on constant mode.
No variations.
If variation occurs it can be made stable
It leads to better manufacturing.
7. CONTROL CHART
Tool use to monitor.
It tells continuous improvement.
All points lie between upper limit and lower limit.
8.
9. FEED RATE
Cut given to component.
Customer requirement.
Depends on CNC machine input.
10. CYCLE TIME
Time to manufacture the component.
Depends upon complete operations.
Components having different cycle time.
12. CONTROL PLAN
A sheet with a drawing of component.
Specification provided.
Operator have to follow the control plan.
Depends upon the customer need
13.
14. PARAMETER TO BE ENSURE
Machine
Parts name
Operation
Customer
Instruments used
15. MEASURING EQUIPMENTS
Measurement is very important for us to know, the job is
coming out in exact size, over size, or under size.
Air- plug gauge
Dial gauge
Micrometer
Lead profile tester
Surface finish tester
16. AIR PLUG GUAGE
Works on compressed air.
Use for measuring OD/ID
Used in microns.
Having master piece before checking
Give exact reading.
17.
18. DIAL GAUGE
Use for measuring thickness.
Can be work in mm and microns.
Measures the thickness no that correct if we dont use
digital gauge.
19.
20. MICROMETER
Use to check measuring over pin.
Used to check distance of teeth.
Check in microns.
21.
22. LEAD PROFILE TESTER
Use to check grinding quality of teeth.
Where the less metal is occurs.
Shows where the variations occurs.
Using of graph paper.
23.
24. SURFACE FINISH TESTER
Tells about the surface finish of the component.
Tells about the life of tool.
Good quality of component obtained.
25.
26. METHADOLOGY
CNC Machine whose behaviour have to check.
Inspect everything inside the machine.
parameters like (room temperature, machine temp.
Etc)
Note down all the parameters of the machine before
running.
27. Set all the equipments to its correct value for measuring
the component.
Let operator put the readings according to control plan in
machine.
Clamp the raw material and start the machine.
Not down cycle time.
Clean the machine if it is not able to clean itself properly.
Take out the job from machine and check is pricesly.
28. TOOLS FOR SPC
Control chart
R- chart
X-chart
Histograms.
29. CONTROL CHART
Control chart shows the variations in jobs.
Having upper limit, lower limit.
Also shows about the rejection on component, having
undersize and oversize.
30. R-CHART, X-CHART & HISTOGRAM
R-Chart shows the ranges.
X-Chart shows the variations.
Histograms shows the highest level of variation.
31. 5 M’S OF SPC
Man
Machine
Method
Material
Mileu
32. ADVANTAGES OF SPC
It improves the performance by reducing variability of
the component.
Improve machine efficiency.
Provide higher quality by reducing variations and
defects.
Minimize rework.
Eliminate unnecessary quality checking process.
Reduce returning of parts from customers.
33. DISADVANTAGE OF SPC
Time taking process.
Repeatable process.
If spc of one machine is done, it doesnt mean the
machine wont need to perform spc again.
Man power need process.
Constantly performing process.
All reading should be specific, coz it can fail the whole
work.