Vhdl modeling of the sram module and state machine controller smc module of rc4 stream cipher algorithm for wi fi encryption

International Journal of Electronics and Communication Engineering & Technology (IJECET), ISSN
0976 – 6464(Print), ISSN 0976 – 6472(Online), Volume 6, Issue 1, January (2015), pp. 79-85 © IAEME
79
VHDL MODELING OF THE SRAM MODULE AND STATE
MACHINE CONTROLLER (SMC) MODULE OF RC4
STREAM CIPHER ALGORITHM FOR Wi-Fi
ENCRYPTION
Dr.A.M. Bhavikatti1
Mallikarjun.Mugali2
1,2
Dept of CSE, BKIT, Bhalki, Karnataka State, India
ABSTRACT
In this paper, VHDL modeling of the SRAM module and State Machine Controller (SMC)
module of RC4 stream cipher algorithm for Wi-Fi encryption is proposed. Various individual
modules of Wi-Fi security have been designed, verified functionally using VHDL-simulator.
In cryptography RC4 is the most widely used software stream cipher and is used in popular protocols
such as Transport Layer Security (TLS) (to protect Internet traffic) and WEP (to secure wireless
networks). While remarkable for its simplicity and speed in software, RC4 has weaknesses that argue
against its use in new systems. It is especially vulnerable when the beginning of the output key
stream is not discarded, or when nonrandom or related keys are used; some ways of using RC4 can
lead to very insecure cryptosystems such as WEP. Many stream ciphers are based on linear feedback
shift registers (LFSRs), which, while efficient in hardware, are less so in software. The design of
RC4 avoids the use of LFSRs, and is ideal for software implementation, as it requires only byte
manipulations. The RC4 algorithm will be implemented by FPGA using VHDL software platform.
Key words: VHDL simulation, RC4 stream cipher, SRAM module, State machine diagram
I. INTRODUCTION TO RC4 STREAM CIPHER
Cryptographic algorithms that can provide fast implementation, small size, low complexity,
and high security for resource-constrained devices such as wireless sensor devices are imperative.
Conventional cryptographic algorithms are very complex and consume significant amount of energy
when used by resource constrained devices for the provision of secure communication, and public
key algorithms are still not feasible in sensor networks for several reasons including limited storage
and excessive energy usage [1]. Therefore, security schemes should rely on a symmetric key
INTERNATIONAL JOURNAL OF ELECTRONICS AND
COMMUNICATION ENGINEERING & TECHNOLOGY (IJECET)
ISSN 0976 – 6464(Print)
ISSN 0976 – 6472(Online)
Volume 6, Issue 1, January (2015), pp. 79-85
© IAEME: http://www.iaeme.com/IJECET.asp
Journal Impact Factor (2015): 7.9817 (Calculated by GISI)
www.jifactor.com
IJECET
© I A E M E

80
cryptography especially when systems have limited hardware resources. There are a number of
stream cipher algorithms presented to implement high performance software including IDEA,
ORYX, LEVIATHAN, MUGI, RC4, Helix, SEAL, SOBER, and SNOW. RC4 is a proprietary
stream cipher which was designed in 1987 by Ron Rivest. RC4 is widely used in security software
based on stream cipher including one in the encryption of traffic to and from secure web sites such as
Transport Layer Security (TLS), Secure Socket Layer (SSL), and Wired Equivalent Privacy (WEP)
implementations. RC4 is fast in comparison to other algorithms and it has a simple design hardware
implementation [2]. For instance, RC4 is five times faster than Data Encryption Standard (DES) and
fifteen times faster than Triple-DES [3].
RC4 has been used as the data encryption algorithm for many applications and protocols.
Some of the protocols and applications using RC4 include the Wi-Fi, Skype, and Bit Torrent, to
name a few. Several efficient approaches to the implementation of RC4 have been proposed [4].
II. PROPOSED BLOCK DIAGRAM OF RC4 STREAM CIPHER
The block diagram of the proposed architecture is shown in Figure1below. The block
diagram can be divided in to 6 different sub modules as shown and these sub modules are i)The
payload data processor and controller ii) SMC iii) Key set up and key stream generation block iv) K-
Stream serializer v) KRAM(256× 8) vi) Multiplexer. As it is not possible to present all the
simulation results in a single paper, it is divided in to three parts and first two parts are already
presented in [5] and [6]. So, these modules are not discussed further in this paper. This paper deals
with simulation of SRAM (256× 8) module, State Machine Controller (SMC) modules and an
analysis of RC4 algorithm state machine diagram.
Fig 1 Simulated module of Wi-Fi Encryption architecture
III. SIMULATION OF SRAM(256× 8) MODULE
The module SRAM is similar to KRAM. It is used to store the data from 0 to 255 at the
address from 0 to 255 i.e. same data is assigned to the same memory location. The address is
assigned by the output of Addr1.In this if MemWr is 1 and MemRd is 0, then data is written in to the
RAM and if if MemWr is 0 and MemRd is 1, then data is read out one by one from the RAM. Data is

International Journal of Electronics and Communication Engineering &
0976 – 6464(Print), ISSN 0976 – 6472(Online), Volume 6, Issue 1, January (2015), pp.
given in parallel form and is read out in parallel
and Fig 3 shows the simulated waveforms of SRAM
Fig 2
IV ANALYSIS OF RC4 ALGORITHM STATE MACHINE DIAGRAM
Different states of state machine
Algorithm state machine diagram.
4.1 Idle state: Data is at original state.
4.2 Initial state: In this state, first we fill the SRAM and KRAM. To fill both the RAM, the data is
given directly to the KRAM for filling the data randomly as a DataBus and address is given by
Addr1.The data at SRAM is filled with the help of
6472(Online), Volume 6, Issue 1, January (2015), pp.
81
in parallel form and is read out in parallel form. Fig 2 shows the simulated module of SRAM
and Fig 3 shows the simulated waveforms of SRAM.
Fig 2 Simulated module of SRAM
Fig 3 Simulated waveforms of SRAM
ALGORITHM STATE MACHINE DIAGRAM
Different states of state machine diagram are explained briefly here.
diagram.
Data is at original state.
In this state, first we fill the SRAM and KRAM. To fill both the RAM, the data is
The data at SRAM is filled with the help of Addr1 which gives the address
Technology (IJECET), ISSN
6472(Online), Volume 6, Issue 1, January (2015), pp. 79-85 © IAEME
Fig 2 shows the simulated module of SRAM
ALGORITHM STATE MACHINE DIAGRAM
are explained briefly here. Fig 4 shows RC4
In this state, first we fill the SRAM and KRAM. To fill both the RAM, the data is
Addr1 which gives the address and at the same

82
time, same data comes from the DataMux and are loaded at the same address. Addr1 gives the
location from 0 to 255(as cnt255) in both the RAM. The output of Addr1 is given to the-----
Fig 4 RC4 Algorithm state machine diagram
---KRAM that gives the address for DataBus of KRAM. The input of SRAM (as Addr[7:0]) show
address and Data fill linearly from DataIn as S0=0, S1=1,S2=2,-------S255=255.The initial state
exists till the SRAM/KRAM fill completely( all 255 locations).After filling, initialOver=1, and state
go to Addr2Cal state.
4.3 Addr2Cal state: In this state, Mux gives the KeyDataOut as MuxOut by selecting the Scl=1, and
SRAM gives the data through DataOut to DataDMux and SellDataOut select this DataOut as SR1
[7:0] and load this value in S_Reg1 and all these values from A2, SR1 and MuxOut are added.
4.4 Addr2Ld state: In this state, the output of Adder 1(Adder 1Out) is loaded in to the Addr2
register.
4.5 SJ State: Loaded value at Addr2 gives j value. This j value is the address, which is selected by
SelAddr(3:0) of AddrMux. The output of AddrMux gives address of SRAM. The value of that
location is obtained as DataOut, selected by DatMux as SR2 [7:0] and stored at S_Reg2 as SJ.
4.6 Swap SI: In this state, the address is taken from Addr2, which is selected by AddrMux as
Addr[7:0] and the data is loaded on this address of SRAM as DataIn by selecting Reg2[7:0] through
DataMux.
4.7 Swap SJ: In this state, the address is taken from Addr1, which is selected by AddrMux as
Addr[7:0] and the data is loaded on this address of SRAM as DataIn by selecting Reg1[7:0] through
DataMux.
All process like Addr2Cal, Addr2Ld, SJ, Swap SI and Swap SJ occurred 255 times. When
Keysetupover=1, Flag=1, then it goes to Addr2Gen state.
4.8 Addr2Gen state: At this state, again we obtained the value of J by KeySetup phase.
4.9TCal state: When Swap SJ is complete, flag will be high and reaches the TCal state.

4.10Kbyte state: The data was given to FIFO in
4.11 Encryption state: The key data byte from K_StreamSerializer and plaintext from
DataSerializer comes out serially in the form of bits.
IV. STATE MACHINE CONTROLLER (SMC) MODULE
This is considered as the
Controller (SMC) module. By this, we can control all the modules .This state machine will work
whenever InitialOver and KeySetUpOver are high.
step. First it controls Addr, SRAM and KRAM. When enable is high means that it was writing key
data in it. Then it is going to the
input and it is given to the SRAM and this process run up to 256 times.
key data bytes is performed. Then it goes to Adder 2Gen.In this state, it takes the data from S_Reg
and gives it to the Adder i.e in Adder 2Ld.It adds the given
the help of AddrMux, which swap it and then gives it to the K_SteamSerilizer. At the same time,
with the help of FIFO, the available
parallel data input to serial output, which is further EX
6(a) and (b) shows the simulation waveforms of State Machine Controller (SMC) module
Fig 5 State Machine Controller (SMC) module
83
The data was given to FIFO in the initial state is now loaded in to DataSerializer.
The key data byte from K_StreamSerializer and plaintext from
DataSerializer comes out serially in the form of bits.
STATE MACHINE CONTROLLER (SMC) MODULE
This is considered as the heart of the whole architecture. Fig 5 shows the State Machine
By this, we can control all the modules .This state machine will work
whenever InitialOver and KeySetUpOver are high. This means that all the modules will work step by
SRAM and KRAM. When enable is high means that it was writing key
another state i.e. Adder 2Ld. In this state, adder will add the given
and it is given to the SRAM and this process run up to 256 times. In this process, swapping of
and gives it to the Adder i.e in Adder 2Ld.It adds the given input and then gives it to the SRAM with
available KeyData is given to the DataSerilizer. Both sterilizers convert
ut to serial output, which is further EX-ORed to give the encrypted data serially.
State Machine Controller (SMC) module
the initial state is now loaded in to DataSerializer.
The key data byte from K_StreamSerializer and plaintext from
Fig 5 shows the State Machine
By this, we can control all the modules .This state machine will work
This means that all the modules will work step by
SRAM and KRAM. When enable is high means that it was writing key
In this state, adder will add the given
In this process, swapping of
input and then gives it to the SRAM with
is given to the DataSerilizer. Both sterilizers convert
ORed to give the encrypted data serially. Fig

Fig 6(a) Simulation waveforms of
Fig 6(b) Simulation waveforms of State Machine Controller (SMC) module
84
Simulation waveforms of State Machine Controller (SMC) module
State Machine Controller (SMC) module

85
T a b l e 1 D e t a i l s o f S i m u la t i o n
V. CONCLUSIONS
Various individual modules of RC4 stream cipher for Wi-Fi security have been designed,
verified functionally using VHDL Simulator, synthesized by the synthesis tool and a final net list has
been created. The proposed design provides high data throughput using 8-bit word and variable key
length, from 8-bit to 128-bit. The proposed system achieves a data throughput of up to 22Mbps at a
clock frequency of 64 MHz .The design has been synthesized using FPGA technology from Xilinx.
Table 1 below shows the details of simulation. The measurement result and comparison with
previous implementation prove that the one proposed is flexible solution for any cryptographic
system.
VI. REFERENCES
1. Sharma K, Ghose MK, Kumar D, Singh RPK, Pandey VK, “A comparative study of various
security approaches used in wireless sensor networks” Int J Adv Sci Technol, 177(77), 2010.
2. Gupta SS, Chattopadhyay A, Sinha K, Maitra S, Sinha B, “ High-performance hardware
implementation for RC4 stream cipher” IEEE Trans Comput 62(4):730–743,2013.
3. Ahmad S, Beg MR, Abbas Q, Ahmad J, Atif S, “ Comparative study between stream cipher
and block cipher using RC4 and Hill Cipher” Int J Comput Appl (0975–8887), 1(25),2010.
4. Disha Handa, Bhanu Kapoor “ State of the Art Realistic Cryptographic Approaches for RC4
Symmetric Stream Cipher”, International Journal on Computational Sciences & Applications
(IJCSA) Vol.4, No.4, August 2014.
5. A.M.Bhavikatti, S. Srinivas Rao “VHDL Modeling of the payload data processor and
controller of RC4 stream cipher for Wi-Fi encryption” ,ICVED-2008, Proceedings of
International Conference on Embedded system & VLSI Design, 20-21 March 2008, at
PDVVP College of Engineering, Ahmednagar.
6. Dr.A.M.Bhavikatti, “VHDL Simulation of KRAM, Multiplexer and K Stream serializer
modules of RC4 Stream Cipher for Wi-Fi Security” ,International Journal of Advances in
Wireless and Mobile Communications (AWMC) ,ISSN 0973-6972, Volume 6, Number 1,
pp17-23,2013.
7. Meha Sharma and Rewa Sharma, “VHDL Implementation of Discrete Wavelet
Transformation For Efficient Power Systems” International journal of Electronics and
Communication Engineering &Technology (IJECET), Volume 1, Issue 1, 2010, pp. 10 - 20,
ISSN Print: 0976- 6464, ISSN Online: 0976 –6472.
8. Sapna and Prof. B. P. Singh, “Low Power SRAM” International journal of Electronics and
Communication Engineering &Technology (IJECET), Volume 4, Issue 2, 2013, pp. 257 -
263, ISSN Print: 0976- 6464, ISSN Online: 0976 –6472.

Vhdl modeling of the sram module and state machine controller smc module of rc4 stream cipher algorithm for wi fi encryption

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Viewers also liked

Viewers also liked (6)

Similar to Vhdl modeling of the sram module and state machine controller smc module of rc4 stream cipher algorithm for wi fi encryption

Similar to Vhdl modeling of the sram module and state machine controller smc module of rc4 stream cipher algorithm for wi fi encryption (20)

More from IAEME Publication

More from IAEME Publication (20)

Recently uploaded

Recently uploaded (20)

Vhdl modeling of the sram module and state machine controller smc module of rc4 stream cipher algorithm for wi fi encryption