The document defines various terms related to concrete masonry units and block laying. It describes the different types of blocks used in construction and how to estimate the number needed. It provides the step-by-step procedure for laying blocks, including spreading mortar, leveling the blocks, cutting blocks as needed, and finishing the joints. It includes illustrations of common techniques for constructing block walls.

1. M.tech Admission in India
By:
admission.edhole.com

2. Masonry Blocks
admission.edhole.com

3. Definitions of terms associated with
concrete masonry units
 A. Masonry Units: Blocks made from concrete, cinders, or other aggregates.
 B. Laying Block: The process of mixing mortar, applying it to masonry block, and
placing the block to create walls.
 C. Mortar Bed: A layer of mortar.
 D. Core: The hollow space in a masonry block.
 E. Corner Pole: A straight piece of wood or metal held plumb by diagonal supports.
 F. Course: A row of masonry units.
 G. Brick Set: Wide chisel used for breaking masonry units.
 H. Hollow Core Block: Masonry block with two or three holes per block.
 I. Masonry: Anything constructed of brick, stone, tile, or concrete unit held in place
with portland concrete.
 J. Lintels: Steel reinforced- concrete beams used for support over windows and doors.
 K. Mortar Board: Board used to hold mortar.
 L. Concrete Sills: Used under windows and doors.
 M. Footer or Footing: A continuous slab of concrete which provides a solid, level
foundation for block or brick
admission.edhole.com

4. Types of Blocks
 A. Stretcher: Used in straight wall sections.
 B. Corner: One flat end to create attractive walls at corners.
 C. Sash: Has special grooves, can be laid to receive window.
 D. Jamb: Use to make door ways so the openings are
attractive and secure.
 E. Half: Used to prevent cutting of blocks when only half a
block is needed.
 F. L-Block: Used as top course of block on a poured floor.
admission.edhole.com

5. Estimating Block
 A. Standard blocks are 8 inches or 2/3 foot high and 16
inches or 1 1/3 foot long when they are laid with a 3/8 inch
mortar joint.
 B. One foot is 3/4 the length of one block, therefore, when
estimating the number of blocks needed for a job, the length of
the wall in feet can be multiplied by 3/4; this gives the
number of blocks per course.
 C. One foot is 3/2 of the height of a block, therefore, the
height of the wall in feet can be multiplied by 3/2 to determine
the number of courses needed.
admission.edhole.com

6. Procedure for laying blocks
 A. Spread a layer of mortar called a mortar bed as the footer.
 B. Position the block on the mortar bed so that its outside corner
rests where the outside corner of the wall should be. Level the
block by first placing the level across the block and then lengthwise
along the block.
 C. Turn several stretcher blocks on end and apply mortar to the ears
with a wiping or swiping stroke of the trowel.
 D. Lay several stretcher blocks in place by working away from the
end or corner block.
E. Use the end of the trowel handle to tap the block until each block
is plumb, level, and the course is straight.
 F. Apply a mortar bed on top of the first course in preparation for the
second course.
 G. If extra strength is needed in the wall, install reinforcement in the
mortar bed.
admission.edhole.com

7. Procedure for laying blocks
 H. As the block laying progresses, cut off excess mortar with the
trowel.
 I. Use a line to keep the courses straight. The line is positioned to
be level along the top of the block.
 J. When a block must be cut, use a mason=s hammer and make
multiple strikes along the line to cut; then make one sharp strike on
the web.
 K. Check the height to be sure each new course is an additional 8
inches high.
 L. After the mortar dries and hardens slightly, finish the joints by
rubbing it with a broken piece of block.
 M. If a joint other than a flush joint is desired, use a jointer to
compress the mortar and create a watertight joint. Tools are
available to create joints that are concave, v-shape, flush or raked.
admission.edhole.com

8. Common concrete blocks used in
building construction
admission.edhole.com

9. Notes: 1. Door openings will have 2" jambs on both sides and top.
2. Door will be a standard height (44" x 6'8").
3. Door sill will accommodate a concrete floor inside.
4. Window openings will accommodate standard size windows.
5. Space above the top of the door will accommodate appropriate trim under the eaves of the roof.
6. Reinforced concrete lintels carry the weight over door and window openings.
7. There are no cut block in the wall. Therefore, the wall can be built with a minimum of cost and labor.
A building front laid out using only whole and half block.
admission.edhole.com

10. Illustrating common method of picking up and
setting concrete blocks
adm ission.edhole.com

11. Placement of corner poles for
constructing a block wall
admission.edhole.com

12. Showing procedure in laying concrete
block walls
admission.edhole.com

13. The usual practice in applying mortar
to concrete blocks
admission.edhole.com

14. A method of laying concrete blocks. Good workmanship
requires straight courses with the face of the wall plumb
and true.
admission.edhole.com

15. Showing detail of joining an interior and
exterior wall in concrete block construction.
admission.edhole.com

16. 8" x 8" x 16" Concrete Block Corner in
the Running Bond
admission.edhole.com

17. Plan View of First Course Layout
typical 3/8" joint
8" x 8" 16" block
admission.edhole.com

18. Types of joint finishes used on block
walls
Concave joint V-Joint Flush Joint Raked
Joint
admission.edhole.com