Intze Overhead Water Tank Design by Working Stress - IS Method.pdf
ย
Draw 224 prelim exam
1. TALISAY CITY COLLEGE
Poblacion, Talisay City Cebu
1st Semester S.Y. 2020-2021
PRELIM EXAMINATION in DRAW 122 (TECHNICAL SKETCHING AND MECHANICAL DRAWING)
INDUSTRIALTECHNOLOGYDEPARTMENT
CR#:_____NAME:__________________________________________ Date: _______________ SCORE: K = ________ P = ________
Course-Yr-Sec: _________________________Time &Days.: ____________________________ Rm. _________
----------------------------------------------------------------------------------------------------------------------------------------------
I. MULTIPLE CHOICE: Read the questions carefully and encircle the letter of the correct answer.
Note: Erasures are considered wrong.
1. Thin dark line use to show outline of object, visible edges and surfaces.
A. Construction line B. Dimension line C. Visible line D. Hidden line
2. Short dash lines use to show non visible surfaces. Usually shows as medium thickness.
A. Construction line B. Dimension line C. Visible line D. Hidden line
3. Very light and thin line use to construct layout work.
A. Construction line B. Dimension line C. Visible line D. Hidden line
4. Thin and dark lines use to show the size of an object with a numeric value.
A. Construction line B. Dimension line C. Visible line D. Hidden line
5. Medium line drawn at 45 degreesuse to show interior view of solid areas of cutting plane line.
A. Phantom line B. Section line C. Leader line D. Cutting plane line
6. Long line followed by twoshort dashes use to show alternate position of a moving part.
A. Phantom line B. Section line C. Leader line D. Cutting plane line
7. Extra thick line use to show cutaway viewsor plane of projection where a section view is taken.
A. Phantom line B. Section line C. Leader line D. Cutting plane line
8. Medium line with arrowhead to show notes or label for size or special information about a feature.
A. Phantom line B. Section line C. Leader line D. Cutting plane line
9. Thin dark line use to show the starting and ending of dimension.
A. Phantom line B. Extension line C. Centre line D. Cutting plane line
10. Long and short dash lines. Usually indicates centre of holes, circles and arcs.
A. Phantom line B. Centre line C. Leader line D. Cutting plane line
11. The process of establishing correspondences betweenthe dimension of our drawing and those of real world object.
A. Depicting B. Dimensioning C. Measuring D. Drawing
12. Are given on drawings by extension lines, dimension lines, leaders, figure, notes, and symbols.
A. Value B. Number C. Notes D. Dimension
13. Are to simplify of complement dimensioning giving information on a drawing in condensed and systematic manner.
A. Value B. Number C. Notes D. Dimension
14. Such a plane which is placed at the front of the object.
A. Frontal Plane B. Horizontal Plane C. Profile Plane D. Rear Plane
15. Such a plane which is place at the right of left side of the object.
A. Frontal Plane B. Horizontal Plane C. Profile Plane D. Rear Plane
2. TEST II: Draw a line using a ruler with the corresponding measurements (2points each)
1. 5 5/16โ
2. 1/4โ
3. 3 7/8โ
TEST III.Identify the alphabet of lines that is shown below.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
TEST IV: Observe the location of holes and curve edges beside. After observing the object,
measure first the isometric planes provided then find the centre of it, thendraw
the holes and curve edges. (20pts)
3. TEST V: Draw an isometric circle on the following planes of orthographic projection. Use compass and 30x60 degrees
triangle. (5points each)
TEST VI: Draw the orthographic views(TOP, FRONT, SIDE VIEW) on the object provided. (5points each)
TEST VII: Provide the exact measurements of the given object below. (5points each)
