1. SERVO-i Ventilator System
Product End-of-Life Disassembly Instructions

2. SERVO-i Ventilator System Product End-of-Life Disassembly Instructions
Important
• The SERVO-i Ventilator System is a medical device • Special waste. This product contains
used in hospital environments. The unit must be electronic and electrical components.
properly cleaned before disassembling. Discard disposable, replaced and left-
over parts in accordance with
Proper cleaning of the unit before Product End-of- appropriate industrial and environmental
Life disassembly must be performed by the former standards.
owner (hospital).
• Recycling. Worn-out batteries must be
recycled or disposed of properly in
accordance with appropriate industrial
and environmental standards.
Environmental declaration
Components with special environmental concern Construction materials
Components listed below shall be disposed of in The construction materials used in SERVO-i in % of
accordance with appropriate industrial and the total weight.
environmental standards.
PC boards (Printed circuit boards) Metal – total 77%
• PC 1770 Main back-plane • Aluminium 69%
• PC 1771 Control, including Lithium battery • Steel, zink, brass 8%
• PC 1772 Monitoring, including Lithium battery
Polymeric material – total 9%
• PC 1775 Plug-and-Play back-plane
• PA (Polyamide)
• PC 1777 Panel including Backlight Inverter
• POM (Polyoxymethylene)
• PC 1778 DC/DC & Standard connectors
• SI (Silicone)
• PC 1780 Pneumatic back-plane
• TPE (Thermoplastic elastomer)
• PC 1781 Pressure transducer, 2 each
• PUR (Polyurethane)
• PC 1784 Expiratory channel
• ABS (Acrylicnitrilebutadienstyrene)
• PC 1785 Expiratory channel connector
• EPDM (Ethylenepropylenedienemonomer)
• PC 1786 Expiratory channel cassette
• PTFE (Polytetrafluoroethylene)
• PC 1789 Remote alarm connector
• FPM (Fluororubber)
Other electronics • NBR (Nitrilerubber)
• TFT assembly including backlight • PP (Polypropylene)
• Touch screen (glass) • PVC (Polyvinyl chloride)
• O2 cell, containing caustic lime and lead (Pb) • PS (Polystyrene)
• O2 Sensor, containing PC boards
Electronics – total 14%
• Gas module Air, containing multiple PC boards
• Battery modules Nickel-Metal Hydride
• Gas module O2, containing multiple PC boards
• Printed circuit boards, cables etc.
• AC/DC Converter, containing PC boards
• Expiratory cassette Others – very small amounts
• Expiratory valve coil • Filter paper of fibre glass
• Safety valve pull magnet
• Battery modules Nickel-Metal Hydride
• Optional function modules
2 MTS-07-0007

3. Product End-of-Life Disassembly Instructions SERVO-i Ventilator System
To open:
1. Disconnect cable.
2. Remove six screws and separate the unit.
Glass
0 PC board
0 $ PC board Other electronics
MTS-07-0007 3

4. SERVO-i Ventilator System Product End-of-Life Disassembly Instructions
Nickel-Metal
Hydride battery
Other electronics
4 MTS-07-0007

5. Product End-of-Life Disassembly Instructions SERVO-i Ventilator System
To open:
1. Pull off filter.
2. Remove four screws.
3. Lift off cover.
PC board
Lithium battery
{
PC board
on PC boards
PC board
Other electronics
$
0
$
0
'
0
MTS-07-0007 5

6. SERVO-i Ventilator System Product End-of-Life Disassembly Instructions
Other
electronics
PC board
Other
electronics
PC board PC board PC board
6 MTS-07-0007

7. Product End-of-Life Disassembly Instructions SERVO-i Ventilator System
Sealed unit,
contains
caustic lime
and lead
Other
electronics
Other
electronics
PC board
Other
electronics
PC board
Other electronics
MTS-07-0007 7

8. © Maquet Critical Care AB, 2007. All rights reserved. MAQUET reserves the right to modify the design and specifications contained herein without prior notice.
Document No.: MTS-07-0007. April 2007. Price group:1. Printed in Sweden.
Maquet Critical Care AB
SE-171 95 Solna, Sweden
Phone: +46 8 730 73 00 GETINGE GROUP is a leading global provider of equipment and
www.maquet.com/criticalcare systems that contribute to quality enhancement and cost efficiency
within healthcare and life sciences. Equipment, services and tech-
For local contact: nologies are supplied under the brands ARJO for patient hygiene,
patient handling and wound care. GETINGE for infection control
Please visit our website and prevention within healthcare and life science and MAQUET for
www.maquet.com Surgical Workplaces, Cardiopulmonary and Critical Care.