Neil Patel's thesis examines the theory, simulation, fabrication and testing of double negative and epsilon near zero metamaterials for microwave applications. Metamaterials are artificially structured materials that can exhibit negative permeability and permittivity. Through simulations in HFSS, various metallic inclusions like split ring resonators, S-shaped split ring resonators, and wire/strip structures are analyzed. Fabricated metamaterial structures are tested in an anechoic chamber, showing transmission properties matching simulations. Prism testing demonstrates negative refraction in the 8-9 GHz range. Simulations also show metamaterials can improve the directivity of radiation from sub-wavelength apertures.
This dissertation presents research on two new samples of active galactic nuclei (AGN): 1) The HRX-BL Lac sample, which is the largest homogeneous sample of BL Lac objects to date, consisting of 77 X-ray selected BL Lac objects identified from a correlation of X-ray and radio sources. Redshifts are known for 81% of the sample. Several peculiar objects were discovered, including the brightest known BL Lac object. 2) A sample of Seyfert II galaxies identified through optical spectroscopy, consisting of 49 objects. The luminosity function of Seyfert II galaxies is derived and compared to other samples. X-ray observations are also used to search for additional Seyfert II galaxies.
This document discusses the design and simulation of microwave resonators using split ring resonators (SRRs) and defected ground structures. It examines individual and coupled SRRs of different orientations and numbers of gaps. Simulation results using HFSS show that adjusting the SRR gap width and orientation can control the cutoff frequency and stop-band attenuation. Coupling SRRs together splits the single resonance into multiple resonances. The design achieves sharp transition bands and high stop-band attenuation, making it suitable for compact low-pass filters.
This dissertation discusses developing a mobile application to regulate server centralization. The existing systems for managing servers and clients are complicated and expensive to operate. The proposed system aims to organize servers and clients through both Windows and mobile applications. It will allow users to manage servers and clients through a mobile app from anywhere at any time at low cost. The system will be created using Java, Android, and MySQL. The server and client apps will be developed in Java using socket programming and Windows API commands. The mobile app will be developed in Android. A MySQL database will store data. The system aims to reduce human effort and costs while improving management of servers and clients.
This thesis analyzes the capacity of hybrid wireless networks with dedicated relays. Two hybrid network models are introduced for load balancing and interference reduction, where dedicated relays positioned at cell borders wirelessly connect to base stations. Analytical approaches are used to obtain the probability of blocking and outage for the models, demonstrating the effectiveness of the hybrid solutions. A signal to interference ratio call admission control scheme is also analyzed for a hybrid CDMA network. Numerical results verify the extensive gain obtained from ad hoc relaying over conventional CDMA networks with this control scheme. Simulation results accurately validate the analytic approaches presented in the thesis.
Global Computing: an Analysis of Trust and Wireless CommunicationsNicola Mezzetti
This document provides an overview of Nicola Mezzetti's Ph.D. thesis which examines trust modeling and verification of trust protocols for wireless systems. The thesis contains two main parts: 1) Developing a computational trust model called SIR based on socio-cognitive models of trust to support trustworthy protocols in open systems. 2) Developing a process calculus called CWS for modeling and verifying wireless communication systems and trust properties within them. The thesis aims to eventually integrate these two parts to allow formal specification and analysis of decentralized reputation systems for wireless networks.
This dissertation discusses implementing radar models and identifying various signal frequencies with remote station alerting. It was submitted by M.Nikhil Kumar, E.Surya Sai Krishna, and T.Raviteja to fulfill their Bachelor of Technology degree in Electronics and Communication Engineering at J.B. Institute of Engineering and Technology under the guidance of Dr. S. Raj Kumar.
This document describes a dissertation submitted by Flavio Felici for the degree of Master of Science in Electrical and Electronic Engineering at the University of Manchester in 2009. The dissertation focuses on developing a low-power wireless network using frequency hopping spread spectrum (FHSS) to connect nodes in a sound masking system. Sound masking systems use loudspeakers and sensors to mask unwanted noises in work environments. Currently these systems use wired connections between nodes, which increases costs. The aim of the project is to add wireless capability to allow more flexible and affordable installation of sound masking system nodes. FHSS is used to enable communication in the unlicensed 2.4GHz ISM band, which is crowded with other wireless devices and protocols.
A study of security in wireless and mobile paymentsJamal Meselmani
Master’s Thesis By Ahmed Ali
Mobile payments are increasing in popularity in recent years. New mobile solutions are being developed in the form of
new Internet capable mobile devices such as the IPhone and new wireless networks such as the LTE and WiMAX
networks.
This report will present, explain and compare some of the most popular wireless networks that enable mobile payments,
from a security point of view. The chosen networks are 3G with connection to GSM and WLAN networks. The main
security mechanisms involved in each network, and how they work will be studied. Security requirements and some of the
most important threats each network faces will be presented and discussed. The main purpose of the report is to examine if
mobile payments offer an acceptable level of security to the average user.
This dissertation presents research on two new samples of active galactic nuclei (AGN): 1) The HRX-BL Lac sample, which is the largest homogeneous sample of BL Lac objects to date, consisting of 77 X-ray selected BL Lac objects identified from a correlation of X-ray and radio sources. Redshifts are known for 81% of the sample. Several peculiar objects were discovered, including the brightest known BL Lac object. 2) A sample of Seyfert II galaxies identified through optical spectroscopy, consisting of 49 objects. The luminosity function of Seyfert II galaxies is derived and compared to other samples. X-ray observations are also used to search for additional Seyfert II galaxies.
This document discusses the design and simulation of microwave resonators using split ring resonators (SRRs) and defected ground structures. It examines individual and coupled SRRs of different orientations and numbers of gaps. Simulation results using HFSS show that adjusting the SRR gap width and orientation can control the cutoff frequency and stop-band attenuation. Coupling SRRs together splits the single resonance into multiple resonances. The design achieves sharp transition bands and high stop-band attenuation, making it suitable for compact low-pass filters.
This dissertation discusses developing a mobile application to regulate server centralization. The existing systems for managing servers and clients are complicated and expensive to operate. The proposed system aims to organize servers and clients through both Windows and mobile applications. It will allow users to manage servers and clients through a mobile app from anywhere at any time at low cost. The system will be created using Java, Android, and MySQL. The server and client apps will be developed in Java using socket programming and Windows API commands. The mobile app will be developed in Android. A MySQL database will store data. The system aims to reduce human effort and costs while improving management of servers and clients.
This thesis analyzes the capacity of hybrid wireless networks with dedicated relays. Two hybrid network models are introduced for load balancing and interference reduction, where dedicated relays positioned at cell borders wirelessly connect to base stations. Analytical approaches are used to obtain the probability of blocking and outage for the models, demonstrating the effectiveness of the hybrid solutions. A signal to interference ratio call admission control scheme is also analyzed for a hybrid CDMA network. Numerical results verify the extensive gain obtained from ad hoc relaying over conventional CDMA networks with this control scheme. Simulation results accurately validate the analytic approaches presented in the thesis.
Global Computing: an Analysis of Trust and Wireless CommunicationsNicola Mezzetti
This document provides an overview of Nicola Mezzetti's Ph.D. thesis which examines trust modeling and verification of trust protocols for wireless systems. The thesis contains two main parts: 1) Developing a computational trust model called SIR based on socio-cognitive models of trust to support trustworthy protocols in open systems. 2) Developing a process calculus called CWS for modeling and verifying wireless communication systems and trust properties within them. The thesis aims to eventually integrate these two parts to allow formal specification and analysis of decentralized reputation systems for wireless networks.
This dissertation discusses implementing radar models and identifying various signal frequencies with remote station alerting. It was submitted by M.Nikhil Kumar, E.Surya Sai Krishna, and T.Raviteja to fulfill their Bachelor of Technology degree in Electronics and Communication Engineering at J.B. Institute of Engineering and Technology under the guidance of Dr. S. Raj Kumar.
This document describes a dissertation submitted by Flavio Felici for the degree of Master of Science in Electrical and Electronic Engineering at the University of Manchester in 2009. The dissertation focuses on developing a low-power wireless network using frequency hopping spread spectrum (FHSS) to connect nodes in a sound masking system. Sound masking systems use loudspeakers and sensors to mask unwanted noises in work environments. Currently these systems use wired connections between nodes, which increases costs. The aim of the project is to add wireless capability to allow more flexible and affordable installation of sound masking system nodes. FHSS is used to enable communication in the unlicensed 2.4GHz ISM band, which is crowded with other wireless devices and protocols.
A study of security in wireless and mobile paymentsJamal Meselmani
Master’s Thesis By Ahmed Ali
Mobile payments are increasing in popularity in recent years. New mobile solutions are being developed in the form of
new Internet capable mobile devices such as the IPhone and new wireless networks such as the LTE and WiMAX
networks.
This report will present, explain and compare some of the most popular wireless networks that enable mobile payments,
from a security point of view. The chosen networks are 3G with connection to GSM and WLAN networks. The main
security mechanisms involved in each network, and how they work will be studied. Security requirements and some of the
most important threats each network faces will be presented and discussed. The main purpose of the report is to examine if
mobile payments offer an acceptable level of security to the average user.
Automatic detection of click fraud in online advertisementsTrieu Nguyen
This thesis presents an approach to automatically detecting click frauds in online advertising.
The approach uses a mathematical theory of evidence to estimate the likelihood of a click whether it is fraud or genuine using web log data of a user‟s activities on the advertiser‟s website. One advantage of the proposed approach is the fact that the likelihood can be computed for each incoming click and thus it gives an online computation of the belief that fits well with the dynamic behaviors of users
Challenges in VoIP Systems - Mostafa Ahmed Mostafa El Beheiry - First Draft F...Mostafa El-Beheiry
This document is a bachelor's thesis submitted by Mostafa Ahmed Mostafa El Beheiry to the German University in Cairo that examines challenges in VoIP (Voice over IP) systems. The thesis identifies four main categories of challenges - security, quality, dependency, and emergency services. It discusses specific issues within each category such as packet sniffing, bandwidth, power outages, and inability to call emergency services. It also includes a simulation of a SPIT (Spam over IP telephony) attack on a VoIP client/server setup. The thesis aims to comprehensively document challenges in VoIP systems and propose possible solutions to advance the field.
This document is a thesis submitted by three students - Farjana Islam, Umme Salma Munmun, and Zareen Rahman - for their Bachelor of Science degree in Computer Science and Engineering. The thesis is titled "A Study on 3G Mobile Technology". It was submitted to and accepted by the Board of Examiners of the Department of Computer Science and Engineering at Manarat International University. The thesis analyzes and compares 3G mobile networks and services to previous generations, highlighting the impact of 3G technology on life, society, and technology in Bangladesh. It discusses the evolution from 2G to 3G standards and the migration challenges faced in implementing 3G networks.
Detecting fraud in cellular telephone networksJamal Meselmani
A Thesis Presented in Partial Fulfillment of the Requirement for the Degree in "MBA" by Hiyam Ali El Tawashi
Telecommunication fraud is a problem that has grown dramatically over the past ten years.
Fraud become a serious global issue for mobile network service providers, it has
undoubtedly become a significant source of revenue losses and bad debts to
telecommunication industry, and with the expected continuing growth in revenue it can be
expected that fraud will increase proportionally.
The research project therefore, focused on how Jawwal Company managing and detecting
the fraud, in order to modify the current tools for more effective fraud prevention and
detection, for this reason the researcher undertook a set of actions that are reported as
follow:
First step it was necessary to understand the problem of telecom fraud, then to know what
makes people perpetrate the fraud, and which are the most prevalent fraud types that are
occurring, clarifying which is the likely products and services to be attacked, what source
of information to facilitate the fraud, how fraudsters perpetrate the fraud finally explaining
the fraud detection and prevention procedures.
Then apply the study on Jawwal Company as study case, by distributing 200
questionnaires to targeted sections, and analyzing the result which shows that the current
fraud management at Jawwal Company is not efficient and needs to be modified.
This undergraduate thesis assessed satellite hospitals and was presented to the Faculty of College of Nursing at Nueva Ecija Colleges in Cabanatuan City in partial fulfillment of the requirements for a Bachelor of Science in Nursing degree. It was authored by five students - Reggielyn L. Libunao, Rainier Josef A. Ramirez, Noriza R. Umipig, Shiela Marie P. Raquepo, and Chermia V. Juachon. The thesis involved reviewing related literature and studies, describing the methods and data sources used, presenting and analyzing collected data, and providing a summary, conclusions, and recommendations.
Final thesis paper Digital Optical fiber link designMd. Nadimul Islam
This document summarizes the literature on digital fiber optic link design. It discusses the history of fiber optics, including the development of early generation systems from the 1970s to 1980s. It also reviews key components of fiber optic links such as transmitters, receivers, fibers, amplifiers, and multiplexing techniques. Dispersion, attenuation, bending loss, and other fiber effects are described. The overview of optical link design covers topics like optical sources, fiber splicing, connectors, and the advantages of fiber optic communication. It introduces the concepts of link power budget and rise time budget used for designing fiber optic systems.
1. The document describes the design and implementation of a pair of horn antennas for a microwave test setup at United International University.
2. It includes designing pyramidal horn antennas using HFSS simulation software, and simulating basic antenna parameters.
3. The results and analysis show that the project was within the students' ability to design and test the horn antennas to fulfill the requirements for their B.Sc. degrees in electrical and electronic engineering.
Metamaterials are artificial structures designed to have unique electromagnetic properties not found in nature, such as a negative refractive index. They are composed of meta-atoms that can manipulate electromagnetic waves at scales smaller than the wavelength of light. Metamaterials have applications in invisibility cloaking, super lenses, compact antennas, absorbing electromagnetic radiation, and mitigating seismic waves. However, designing metamaterials for specific wavelengths is challenging, and they do not work perfectly and are very expensive.
This document describes a wireless accident tracking system that uses vibration sensors, GPS, and GSM networks to detect vehicle accidents and send alerts. When an accident occurs, the vibration sensor detects it and sends a signal to the microcontroller. The microcontroller then switches on the GPS and GSM modules. The GPS module obtains the location coordinates, which are sent via GSM to emergency services. This system allows for quick response in remote areas to minimize accident severity.
The existing outage management system has several limitations:
1. It uses in-house tools to extract data from the distribution management system and Excel to calculate reliability metrics, which takes weeks to generate canned reports with no flexibility.
2. The calculation of reliability indices is a manual process that requires examining each event, increasing reporting time.
3. There is no system to calculate reliability metrics and prioritize work based on outages, nor to notify high management of major outages impacting many customers.
The client needs a new outage management system to more accurately and efficiently calculate reliability indices, generate flexible reports, and notify stakeholders of significant outages.
1. The document discusses the evolution of wireless technologies from 1G to 5G, outlining the key features and drawbacks of each generation.
2. Early generations like 1G provided basic voice calling using analog signals at speeds up to 2.4kbps but had issues like poor battery life and voice quality. 2G introduced digital signals and SMS at speeds up to 64kbps.
3. Later generations such as 3G (144kbps-2Mbps), 4G (100Mbps-1Gbps), and emerging 5G (expected speeds over 1Gbps) have provided significantly higher data speeds and capabilities like video calling, but also face challenges around implementation costs, bandwidth requirements, and
The document provides a final presentation on improving quality and productivity in the construction of telecom towers. It identifies key issues with current construction practices such as poor quality, cost overruns, and delays. The objectives are to study contracting procedures and suggest productivity improvements. Site visits found issues with materials, formwork, soil conditions, concrete, labor, and management. Process mapping is applied to identify processes for improvement like material staging. Suggestions include better supervision, equipment use, and safety practices.
In the present era the technology in communications has developed to a very large extent. The communication industries have seen a tremendous increase in last few years which have resulted in installation of large number of towers to increase the coverage area and network consistency. In wireless communication network these towers play a significant role hence failure of such structure in a disaster is a major concern. Therefore utmost importance should be given in considering all possible extreme conditions for designing these towers. In most of the studies, the researches have considered the effect of wind only on the four legged self-supporting towers. In this dissertation, a four legged lattice tower is analyzed and designed along with foundation details.
This document discusses point to point microwave transmission. It describes the basic modules of microwave radio terminals including digital modems, RF units, and passive parabolic antennas. It also covers microwave radio configurations, applications, advantages, planning aspects like network architecture, frequency bands, and propagation effects. Key factors in microwave link engineering like link budgets, reliability predictions, and interference analysis are summarized.
This document is a project report submitted by Vanhishikha Bhargava to fulfill requirements for a Bachelor of Technology degree. The report explores various topics related to optical fibers including the basics of fiber optics, fiber types, standards, connectors, losses, splitters, splicing, and wavelength division multiplexing. The report includes an index listing the various sections, introduction, acknowledgments, company profile, and conclusions. It was supervised by Mr. Vinod C.P from Advanced Fiber Systems Pvt. Ltd and submitted to the Department of Electronics and Communication at G.N.I.T. (Girls) GREATER NOIDA.
This document is an undergraduate thesis that examines the opto-electronic properties of hydrogenated silicon carbide (SiC:H) using 3D ternary diagrams. It begins with background on amorphous silicon and silicon carbide materials. It then discusses using ternary diagrams to model the composition ratio and compare optical parameters to composition. The thesis aims to determine how carbon, silicon, and hydrogen ratios affect the optical bandgap, refractive index, and mass density of SiC:H. Experimental data is analyzed using the 3D ternary diagram model to show that carbon ratio strongly influences bandgap, while refractive index and density depend more on hydrogen variation.
Evangelos_Stergiou_Planar Spirals for Multiband Antenna Radiators.Evangelos Stergiou
This document outlines a student's MSc project investigating planar spiral resonators for multiband antenna applications. The project will analyze single-arm and dual-arm paired spiral resonator designs using different feeding techniques, including edge discrete port feeding and coaxial probe feeding. Simulations will be performed using CST Microwave Studio to evaluate antenna performance parameters and investigate design improvements such as bottom spiral rotation and use of shorting pins. The goal is to achieve high performance multiband operation of the interwoven spiral resonator configurations.
This document is a master's thesis submitted by Billal Pervaz to the University of Siegen that investigates using x-ray free electron lasers (FELs) to measure x-ray resonant reflectivities and study ultrafast demagnetization. The thesis provides background on x-ray reflectivity, resonant scattering, x-ray magnetic circular dichroism (XMCD), and FELs. It then describes experiments performed at the FERMI FEL in Italy to measure magnetic reflectivities of samples using XMCD for the first time with an FEL. Preliminary results showed asymmetries hinting at effects of high x-ray fluence on material absorption, though there were deviations from calculations
This document is a thesis written by Martin Løkke Nielsen on triangular photonic band gap crystals and their implementation in air-guiding optical fibers. The thesis uses group theory extensively to predict properties of photonic crystals without having to numerically solve Maxwell's equations. It investigates in-plane and out-of-plane band gaps, effects of introducing interstitial holes or defects, and designs crystal structures to confine defect modes to potential use in optical fibers. Numerical calculations using the MPB software package verify the group theory predictions and optimize crystal designs for fiber implementation.
The document discusses computational modeling of perovskites for photovoltaic applications. Perovskites have shown great promise for solar cells due to their excellent optoelectronic properties. Computational modeling can provide insights into perovskite properties that are difficult to obtain experimentally. While lead-based perovskites have achieved high efficiencies, their toxicity is a concern, creating interest in developing non-toxic alternatives through computational studies and materials design. Opportunities and challenges of computational modeling for understanding perovskites and designing new materials are also examined.
Automatic detection of click fraud in online advertisementsTrieu Nguyen
This thesis presents an approach to automatically detecting click frauds in online advertising.
The approach uses a mathematical theory of evidence to estimate the likelihood of a click whether it is fraud or genuine using web log data of a user‟s activities on the advertiser‟s website. One advantage of the proposed approach is the fact that the likelihood can be computed for each incoming click and thus it gives an online computation of the belief that fits well with the dynamic behaviors of users
Challenges in VoIP Systems - Mostafa Ahmed Mostafa El Beheiry - First Draft F...Mostafa El-Beheiry
This document is a bachelor's thesis submitted by Mostafa Ahmed Mostafa El Beheiry to the German University in Cairo that examines challenges in VoIP (Voice over IP) systems. The thesis identifies four main categories of challenges - security, quality, dependency, and emergency services. It discusses specific issues within each category such as packet sniffing, bandwidth, power outages, and inability to call emergency services. It also includes a simulation of a SPIT (Spam over IP telephony) attack on a VoIP client/server setup. The thesis aims to comprehensively document challenges in VoIP systems and propose possible solutions to advance the field.
This document is a thesis submitted by three students - Farjana Islam, Umme Salma Munmun, and Zareen Rahman - for their Bachelor of Science degree in Computer Science and Engineering. The thesis is titled "A Study on 3G Mobile Technology". It was submitted to and accepted by the Board of Examiners of the Department of Computer Science and Engineering at Manarat International University. The thesis analyzes and compares 3G mobile networks and services to previous generations, highlighting the impact of 3G technology on life, society, and technology in Bangladesh. It discusses the evolution from 2G to 3G standards and the migration challenges faced in implementing 3G networks.
Detecting fraud in cellular telephone networksJamal Meselmani
A Thesis Presented in Partial Fulfillment of the Requirement for the Degree in "MBA" by Hiyam Ali El Tawashi
Telecommunication fraud is a problem that has grown dramatically over the past ten years.
Fraud become a serious global issue for mobile network service providers, it has
undoubtedly become a significant source of revenue losses and bad debts to
telecommunication industry, and with the expected continuing growth in revenue it can be
expected that fraud will increase proportionally.
The research project therefore, focused on how Jawwal Company managing and detecting
the fraud, in order to modify the current tools for more effective fraud prevention and
detection, for this reason the researcher undertook a set of actions that are reported as
follow:
First step it was necessary to understand the problem of telecom fraud, then to know what
makes people perpetrate the fraud, and which are the most prevalent fraud types that are
occurring, clarifying which is the likely products and services to be attacked, what source
of information to facilitate the fraud, how fraudsters perpetrate the fraud finally explaining
the fraud detection and prevention procedures.
Then apply the study on Jawwal Company as study case, by distributing 200
questionnaires to targeted sections, and analyzing the result which shows that the current
fraud management at Jawwal Company is not efficient and needs to be modified.
This undergraduate thesis assessed satellite hospitals and was presented to the Faculty of College of Nursing at Nueva Ecija Colleges in Cabanatuan City in partial fulfillment of the requirements for a Bachelor of Science in Nursing degree. It was authored by five students - Reggielyn L. Libunao, Rainier Josef A. Ramirez, Noriza R. Umipig, Shiela Marie P. Raquepo, and Chermia V. Juachon. The thesis involved reviewing related literature and studies, describing the methods and data sources used, presenting and analyzing collected data, and providing a summary, conclusions, and recommendations.
Final thesis paper Digital Optical fiber link designMd. Nadimul Islam
This document summarizes the literature on digital fiber optic link design. It discusses the history of fiber optics, including the development of early generation systems from the 1970s to 1980s. It also reviews key components of fiber optic links such as transmitters, receivers, fibers, amplifiers, and multiplexing techniques. Dispersion, attenuation, bending loss, and other fiber effects are described. The overview of optical link design covers topics like optical sources, fiber splicing, connectors, and the advantages of fiber optic communication. It introduces the concepts of link power budget and rise time budget used for designing fiber optic systems.
1. The document describes the design and implementation of a pair of horn antennas for a microwave test setup at United International University.
2. It includes designing pyramidal horn antennas using HFSS simulation software, and simulating basic antenna parameters.
3. The results and analysis show that the project was within the students' ability to design and test the horn antennas to fulfill the requirements for their B.Sc. degrees in electrical and electronic engineering.
Metamaterials are artificial structures designed to have unique electromagnetic properties not found in nature, such as a negative refractive index. They are composed of meta-atoms that can manipulate electromagnetic waves at scales smaller than the wavelength of light. Metamaterials have applications in invisibility cloaking, super lenses, compact antennas, absorbing electromagnetic radiation, and mitigating seismic waves. However, designing metamaterials for specific wavelengths is challenging, and they do not work perfectly and are very expensive.
This document describes a wireless accident tracking system that uses vibration sensors, GPS, and GSM networks to detect vehicle accidents and send alerts. When an accident occurs, the vibration sensor detects it and sends a signal to the microcontroller. The microcontroller then switches on the GPS and GSM modules. The GPS module obtains the location coordinates, which are sent via GSM to emergency services. This system allows for quick response in remote areas to minimize accident severity.
The existing outage management system has several limitations:
1. It uses in-house tools to extract data from the distribution management system and Excel to calculate reliability metrics, which takes weeks to generate canned reports with no flexibility.
2. The calculation of reliability indices is a manual process that requires examining each event, increasing reporting time.
3. There is no system to calculate reliability metrics and prioritize work based on outages, nor to notify high management of major outages impacting many customers.
The client needs a new outage management system to more accurately and efficiently calculate reliability indices, generate flexible reports, and notify stakeholders of significant outages.
1. The document discusses the evolution of wireless technologies from 1G to 5G, outlining the key features and drawbacks of each generation.
2. Early generations like 1G provided basic voice calling using analog signals at speeds up to 2.4kbps but had issues like poor battery life and voice quality. 2G introduced digital signals and SMS at speeds up to 64kbps.
3. Later generations such as 3G (144kbps-2Mbps), 4G (100Mbps-1Gbps), and emerging 5G (expected speeds over 1Gbps) have provided significantly higher data speeds and capabilities like video calling, but also face challenges around implementation costs, bandwidth requirements, and
The document provides a final presentation on improving quality and productivity in the construction of telecom towers. It identifies key issues with current construction practices such as poor quality, cost overruns, and delays. The objectives are to study contracting procedures and suggest productivity improvements. Site visits found issues with materials, formwork, soil conditions, concrete, labor, and management. Process mapping is applied to identify processes for improvement like material staging. Suggestions include better supervision, equipment use, and safety practices.
In the present era the technology in communications has developed to a very large extent. The communication industries have seen a tremendous increase in last few years which have resulted in installation of large number of towers to increase the coverage area and network consistency. In wireless communication network these towers play a significant role hence failure of such structure in a disaster is a major concern. Therefore utmost importance should be given in considering all possible extreme conditions for designing these towers. In most of the studies, the researches have considered the effect of wind only on the four legged self-supporting towers. In this dissertation, a four legged lattice tower is analyzed and designed along with foundation details.
This document discusses point to point microwave transmission. It describes the basic modules of microwave radio terminals including digital modems, RF units, and passive parabolic antennas. It also covers microwave radio configurations, applications, advantages, planning aspects like network architecture, frequency bands, and propagation effects. Key factors in microwave link engineering like link budgets, reliability predictions, and interference analysis are summarized.
This document is a project report submitted by Vanhishikha Bhargava to fulfill requirements for a Bachelor of Technology degree. The report explores various topics related to optical fibers including the basics of fiber optics, fiber types, standards, connectors, losses, splitters, splicing, and wavelength division multiplexing. The report includes an index listing the various sections, introduction, acknowledgments, company profile, and conclusions. It was supervised by Mr. Vinod C.P from Advanced Fiber Systems Pvt. Ltd and submitted to the Department of Electronics and Communication at G.N.I.T. (Girls) GREATER NOIDA.
This document is an undergraduate thesis that examines the opto-electronic properties of hydrogenated silicon carbide (SiC:H) using 3D ternary diagrams. It begins with background on amorphous silicon and silicon carbide materials. It then discusses using ternary diagrams to model the composition ratio and compare optical parameters to composition. The thesis aims to determine how carbon, silicon, and hydrogen ratios affect the optical bandgap, refractive index, and mass density of SiC:H. Experimental data is analyzed using the 3D ternary diagram model to show that carbon ratio strongly influences bandgap, while refractive index and density depend more on hydrogen variation.
Evangelos_Stergiou_Planar Spirals for Multiband Antenna Radiators.Evangelos Stergiou
This document outlines a student's MSc project investigating planar spiral resonators for multiband antenna applications. The project will analyze single-arm and dual-arm paired spiral resonator designs using different feeding techniques, including edge discrete port feeding and coaxial probe feeding. Simulations will be performed using CST Microwave Studio to evaluate antenna performance parameters and investigate design improvements such as bottom spiral rotation and use of shorting pins. The goal is to achieve high performance multiband operation of the interwoven spiral resonator configurations.
This document is a master's thesis submitted by Billal Pervaz to the University of Siegen that investigates using x-ray free electron lasers (FELs) to measure x-ray resonant reflectivities and study ultrafast demagnetization. The thesis provides background on x-ray reflectivity, resonant scattering, x-ray magnetic circular dichroism (XMCD), and FELs. It then describes experiments performed at the FERMI FEL in Italy to measure magnetic reflectivities of samples using XMCD for the first time with an FEL. Preliminary results showed asymmetries hinting at effects of high x-ray fluence on material absorption, though there were deviations from calculations
This document is a thesis written by Martin Løkke Nielsen on triangular photonic band gap crystals and their implementation in air-guiding optical fibers. The thesis uses group theory extensively to predict properties of photonic crystals without having to numerically solve Maxwell's equations. It investigates in-plane and out-of-plane band gaps, effects of introducing interstitial holes or defects, and designs crystal structures to confine defect modes to potential use in optical fibers. Numerical calculations using the MPB software package verify the group theory predictions and optimize crystal designs for fiber implementation.
The document discusses computational modeling of perovskites for photovoltaic applications. Perovskites have shown great promise for solar cells due to their excellent optoelectronic properties. Computational modeling can provide insights into perovskite properties that are difficult to obtain experimentally. While lead-based perovskites have achieved high efficiencies, their toxicity is a concern, creating interest in developing non-toxic alternatives through computational studies and materials design. Opportunities and challenges of computational modeling for understanding perovskites and designing new materials are also examined.
This document discusses research into controlling electron spin dynamics in semiconductor structures using optical techniques. The motivation is to better understand fundamental spin properties like dephasing and relaxation, and to demonstrate new control schemes. Experiments use GaAs materials with optical excitation and detection of electron spins. Time-resolved Kerr rotation measurements directly probe spin dynamics with picosecond time resolution. Results often show unexpected behavior that requires further investigation. The goal is to advance spin-based technologies like spintronics and quantum information processing.
This dissertation studies synthetic molecular motors and self-assembled monolayers through computational modeling and simulation. Chapter 1 provides background on molecular motors and the theoretical methods used, including density functional theory and classical force fields. Chapter 2 models a caltrop-based rotary motor driven by rotating electric fields, finding resonance effects that enhance friction. Chapter 3 presents a novel power law mechanism for dissipation in motors indirectly coupled to a thermal bath. Chapter 4 models the kinetics of monolayer displacement and finds it follows a universal perimeter-dependent growth model. Chapter 5 provides preliminary results on barriers to rotation in lanthanide double-decker complexes as potential rotary motors.
The document describes the design and testing of a birdcage coil to emulate the RF fields of an MRI machine. The coil was designed to resonate at 128 MHz but was found to resonate at 156 MHz due to unforeseen factors. A quadrature hybrid splitter was designed to drive the coil but was incompatible with its 156 MHz resonance. Testing showed 25-30% power reflection when driving the coil from a single port. An experiment heated a copper wire by 0.7°C over 10 minutes when driven by the coil at 156 MHz. Further modifications are needed to address issues with the coil's resonance frequency and power delivery.
The document is a library release form granting permission to the University of Ontario Institute of Technology Library to reproduce and lend or sell copies of a thesis titled "Design, Analysis and Validation of Electrode-less Plasma Generation" submitted by Daniel Bondarenko in partial fulfillment of a Master's of Applied Science degree awarded in 2016. The form is signed by Daniel Bondarenko and contains his contact information.
This document describes an investigation of the LaAlO3-SrTiO3 (LAO-STO) heterointerface using transmission electron microscopy (TEM). The sample was prepared using pulsed laser deposition to grow a thin film of LAO on a STO substrate, followed by ion slicing to produce a wedge-shaped cross-section for TEM analysis. The TEM results revealed a high-density two-dimensional electron gas formed at the LAO-STO interface, which has potential applications in next-generation electronic devices and holds promise for novel electronic properties.
Computer Integrated Design, Analysis and Shape Optimization of Proton Beam DumpIRJET Journal
This document discusses the computer integrated design, analysis, and shape optimization of a proton beam dump. It first provides background on spallation neutron sources and the issues they present, such as induced radioactivity. It then reviews previous literature on related topics like negative ion sources and beam dump design. The document proposes using simulation software to derive results from one module to input into another for shape optimization of the beam dump's cooling channel, ensuring thermal and structural stability for high-powered proton beams.
This document summarizes a master's thesis that studied irradiation-induced swelling in two ODS steels. Samples of a 15CRA-3 alloy and a PM2000 alloy were irradiated with helium ions from room temperature to 800°C to a dose of 0.84 dpa with 4000 appm helium/dpa. Surface displacements were measured using white light interferometry. Low swelling was found in both alloys, with the PM2000 showing slightly higher swelling of around 0.8%/dpa at 600°C compared to 0.3%/dpa for 15CRA-3 over the full temperature range. The higher swelling resistance of 15CRA-3 is attributed to its finer
The document outlines the design of a helical resonator for use in a penning ion trap. It discusses different types of resonators and why a helical design is best. The document provides details on the design parameters and theoretical calculations for a 190 MHz helical resonator. Simulations of the resonator were performed using HFSS software, finding good agreement with theoretical resonant frequency and Q-factor values. The effect of different capacitive loads on resonant frequency was also studied through simulations. In conclusion, the helical resonator design is suitable for detection of charged particles in the penning ion trap application.
This document describes Marco Antonio Escobar Acevedo's Master's thesis which compares calculations of nonlinear optical response in semiconductors using two different gauges: the length gauge and transversal gauge. The thesis derives the expressions for calculating second-order optical susceptibilities in both gauges from quantum mechanics perturbation theory. It then presents ab initio calculations of second-order optical susceptibilities for GaAs using the local density approximation with scissors corrections. The results from both gauges are compared and the issue of gauge invariance in the calculations is discussed.
This document discusses a thesis project that aims to evaluate the radiation hardness of sensor materials for use in the proposed International Linear Collider beamline calorimeter (BeamCal). The author performs Monte Carlo simulations to estimate the shower conversion factor α, which quantifies the mean radiation fluence at a sensor per incident electron, as a function of electron energy. Analysis of the simulation data provides fluence distribution profiles that decrease radially from the center of the irradiated sensor area. The author accounts for sensor rastering across the electron beam, which provides even illumination over a 2 cm area. Observations from the simulations indicate the radiation fluence is linearly dependent on the incident electron energy.
Predicting local atomic structures from X-ray absorption spectroscopy using t...aimsnist
The document discusses using theory, computation, and machine learning to interpret experimental X-ray absorption spectroscopy data and determine local atomic structures. It presents examples of using density functional theory calculations of X-ray absorption near edge structure (XANES) spectra to benchmark predictions against experiments and develop machine learning models for structure classification. The models are able to classify local structures like tetrahedral, square pyramidal, and octahedral coordination with over 85% accuracy across different materials systems. This approach provides a way to solve the inverse problem of determining structures from spectroscopy measurements in real time.
Tor A Fjeldly and Muhammad Nawaz submitted a master's thesis on the formation of silicon nanostructures in silicon nitride thin films for use in solar cells. The goal was to develop silicon nitride anti-reflective coatings containing silicon nanoparticles and characterize the films using ellipsometry. Seven silicon nitride films with varying stoichiometry were deposited using PECVD and characterized with ellipsometry, photoluminescence, and transmission electron microscopy before and after annealing. Ellipsometry showed the films became more compact after annealing with increased refractive index. Photoluminescence was observed for samples with high ammonia flow but decreased after annealing, while samples with low ammonia flow showed little photolum
This dissertation develops first-principles thermodynamic models for the hexagonal close-packed ε-Fe-N system. The work is divided into two parts. The first part develops a generalized quasiharmonic phonon model to describe the vibrational contributions to the thermodynamics. This model is applied to ε-Fe3N and accurately predicts its thermal expansion and volume-pressure relationship. The second part uses thermodynamic statistical sampling via Monte Carlo simulations and a cluster expansion to describe the configurational degrees of freedom of nitrogen occupation in the system. This allows modeling of ordering phenomena and phase transitions. The model predicts an ε → ζ phase transition in agreement with experiments.
This dissertation by Harsh Pandey investigates the manipulation and separation of objects at the microscale using simulations and microfluidic experiments. The document includes 7 chapters that cover: 1) developing a coarse-grained model to simulate the conformation-dependent electrophoretic mobility of polymers, 2) using the model to simulate the trapping and manipulation of deformable objects in microfluidic devices, 3) simulating the trapping of rigid objects using electric and flow fields, 4) microfluidic experiments observing the behavior of particles under flow and electric fields, 5) simulating the self-assembly of polymers at liquid interfaces, and 6) conclusions and potential future directions. The overall goal is to better understand and
Hindered Rotation of Dihydrogen on Synthesized Metal OxidesGeorge Rouvelas
This thesis discusses the synthesis of magnesium oxide and zinc oxide nanoparticles and examines the rotational eigenstates of molecular hydrogen interacting with metal oxide surfaces. Single morphology nanocubes of magnesium oxide were consistently produced. Zinc oxide synthesis resulted in a mixture of tetrapods, kites, and hexagonal pillars. A MATLAB program was used to calculate the rotational energies of hydrogen and deuterium molecules in the presence of an anisotropic hindering potential, meant to model interactions with a metal oxide surface. An increase in the hindering potential about the azimuthal angle was found to lift the degeneracy of the mj = ±1 states.
Similar to Theory simulation fabrication and testing of double negative an (20)
A Comprehensive Guide to DeFi Development Services in 2024Intelisync
DeFi represents a paradigm shift in the financial industry. Instead of relying on traditional, centralized institutions like banks, DeFi leverages blockchain technology to create a decentralized network of financial services. This means that financial transactions can occur directly between parties, without intermediaries, using smart contracts on platforms like Ethereum.
In 2024, we are witnessing an explosion of new DeFi projects and protocols, each pushing the boundaries of what’s possible in finance.
In summary, DeFi in 2024 is not just a trend; it’s a revolution that democratizes finance, enhances security and transparency, and fosters continuous innovation. As we proceed through this presentation, we'll explore the various components and services of DeFi in detail, shedding light on how they are transforming the financial landscape.
At Intelisync, we specialize in providing comprehensive DeFi development services tailored to meet the unique needs of our clients. From smart contract development to dApp creation and security audits, we ensure that your DeFi project is built with innovation, security, and scalability in mind. Trust Intelisync to guide you through the intricate landscape of decentralized finance and unlock the full potential of blockchain technology.
Ready to take your DeFi project to the next level? Partner with Intelisync for expert DeFi development services today!
Digital Marketing Trends in 2024 | Guide for Staying AheadWask
https://www.wask.co/ebooks/digital-marketing-trends-in-2024
Feeling lost in the digital marketing whirlwind of 2024? Technology is changing, consumer habits are evolving, and staying ahead of the curve feels like a never-ending pursuit. This e-book is your compass. Dive into actionable insights to handle the complexities of modern marketing. From hyper-personalization to the power of user-generated content, learn how to build long-term relationships with your audience and unlock the secrets to success in the ever-shifting digital landscape.
Introduction of Cybersecurity with OSS at Code Europe 2024Hiroshi SHIBATA
I develop the Ruby programming language, RubyGems, and Bundler, which are package managers for Ruby. Today, I will introduce how to enhance the security of your application using open-source software (OSS) examples from Ruby and RubyGems.
The first topic is CVE (Common Vulnerabilities and Exposures). I have published CVEs many times. But what exactly is a CVE? I'll provide a basic understanding of CVEs and explain how to detect and handle vulnerabilities in OSS.
Next, let's discuss package managers. Package managers play a critical role in the OSS ecosystem. I'll explain how to manage library dependencies in your application.
I'll share insights into how the Ruby and RubyGems core team works to keep our ecosystem safe. By the end of this talk, you'll have a better understanding of how to safeguard your code.
Main news related to the CCS TSI 2023 (2023/1695)Jakub Marek
An English 🇬🇧 translation of a presentation to the speech I gave about the main changes brought by CCS TSI 2023 at the biggest Czech conference on Communications and signalling systems on Railways, which was held in Clarion Hotel Olomouc from 7th to 9th November 2023 (konferenceszt.cz). Attended by around 500 participants and 200 on-line followers.
The original Czech 🇨🇿 version of the presentation can be found here: https://www.slideshare.net/slideshow/hlavni-novinky-souvisejici-s-ccs-tsi-2023-2023-1695/269688092 .
The videorecording (in Czech) from the presentation is available here: https://youtu.be/WzjJWm4IyPk?si=SImb06tuXGb30BEH .
Programming Foundation Models with DSPy - Meetup SlidesZilliz
Prompting language models is hard, while programming language models is easy. In this talk, I will discuss the state-of-the-art framework DSPy for programming foundation models with its powerful optimizers and runtime constraint system.
Driving Business Innovation: Latest Generative AI Advancements & Success StorySafe Software
Are you ready to revolutionize how you handle data? Join us for a webinar where we’ll bring you up to speed with the latest advancements in Generative AI technology and discover how leveraging FME with tools from giants like Google Gemini, Amazon, and Microsoft OpenAI can supercharge your workflow efficiency.
During the hour, we’ll take you through:
Guest Speaker Segment with Hannah Barrington: Dive into the world of dynamic real estate marketing with Hannah, the Marketing Manager at Workspace Group. Hear firsthand how their team generates engaging descriptions for thousands of office units by integrating diverse data sources—from PDF floorplans to web pages—using FME transformers, like OpenAIVisionConnector and AnthropicVisionConnector. This use case will show you how GenAI can streamline content creation for marketing across the board.
Ollama Use Case: Learn how Scenario Specialist Dmitri Bagh has utilized Ollama within FME to input data, create custom models, and enhance security protocols. This segment will include demos to illustrate the full capabilities of FME in AI-driven processes.
Custom AI Models: Discover how to leverage FME to build personalized AI models using your data. Whether it’s populating a model with local data for added security or integrating public AI tools, find out how FME facilitates a versatile and secure approach to AI.
We’ll wrap up with a live Q&A session where you can engage with our experts on your specific use cases, and learn more about optimizing your data workflows with AI.
This webinar is ideal for professionals seeking to harness the power of AI within their data management systems while ensuring high levels of customization and security. Whether you're a novice or an expert, gain actionable insights and strategies to elevate your data processes. Join us to see how FME and AI can revolutionize how you work with data!
In the realm of cybersecurity, offensive security practices act as a critical shield. By simulating real-world attacks in a controlled environment, these techniques expose vulnerabilities before malicious actors can exploit them. This proactive approach allows manufacturers to identify and fix weaknesses, significantly enhancing system security.
This presentation delves into the development of a system designed to mimic Galileo's Open Service signal using software-defined radio (SDR) technology. We'll begin with a foundational overview of both Global Navigation Satellite Systems (GNSS) and the intricacies of digital signal processing.
The presentation culminates in a live demonstration. We'll showcase the manipulation of Galileo's Open Service pilot signal, simulating an attack on various software and hardware systems. This practical demonstration serves to highlight the potential consequences of unaddressed vulnerabilities, emphasizing the importance of offensive security practices in safeguarding critical infrastructure.
Best 20 SEO Techniques To Improve Website Visibility In SERPPixlogix Infotech
Boost your website's visibility with proven SEO techniques! Our latest blog dives into essential strategies to enhance your online presence, increase traffic, and rank higher on search engines. From keyword optimization to quality content creation, learn how to make your site stand out in the crowded digital landscape. Discover actionable tips and expert insights to elevate your SEO game.
How to Interpret Trends in the Kalyan Rajdhani Mix Chart.pdfChart Kalyan
A Mix Chart displays historical data of numbers in a graphical or tabular form. The Kalyan Rajdhani Mix Chart specifically shows the results of a sequence of numbers over different periods.
Monitoring and Managing Anomaly Detection on OpenShift.pdfTosin Akinosho
Monitoring and Managing Anomaly Detection on OpenShift
Overview
Dive into the world of anomaly detection on edge devices with our comprehensive hands-on tutorial. This SlideShare presentation will guide you through the entire process, from data collection and model training to edge deployment and real-time monitoring. Perfect for those looking to implement robust anomaly detection systems on resource-constrained IoT/edge devices.
Key Topics Covered
1. Introduction to Anomaly Detection
- Understand the fundamentals of anomaly detection and its importance in identifying unusual behavior or failures in systems.
2. Understanding Edge (IoT)
- Learn about edge computing and IoT, and how they enable real-time data processing and decision-making at the source.
3. What is ArgoCD?
- Discover ArgoCD, a declarative, GitOps continuous delivery tool for Kubernetes, and its role in deploying applications on edge devices.
4. Deployment Using ArgoCD for Edge Devices
- Step-by-step guide on deploying anomaly detection models on edge devices using ArgoCD.
5. Introduction to Apache Kafka and S3
- Explore Apache Kafka for real-time data streaming and Amazon S3 for scalable storage solutions.
6. Viewing Kafka Messages in the Data Lake
- Learn how to view and analyze Kafka messages stored in a data lake for better insights.
7. What is Prometheus?
- Get to know Prometheus, an open-source monitoring and alerting toolkit, and its application in monitoring edge devices.
8. Monitoring Application Metrics with Prometheus
- Detailed instructions on setting up Prometheus to monitor the performance and health of your anomaly detection system.
9. What is Camel K?
- Introduction to Camel K, a lightweight integration framework built on Apache Camel, designed for Kubernetes.
10. Configuring Camel K Integrations for Data Pipelines
- Learn how to configure Camel K for seamless data pipeline integrations in your anomaly detection workflow.
11. What is a Jupyter Notebook?
- Overview of Jupyter Notebooks, an open-source web application for creating and sharing documents with live code, equations, visualizations, and narrative text.
12. Jupyter Notebooks with Code Examples
- Hands-on examples and code snippets in Jupyter Notebooks to help you implement and test anomaly detection models.
FREE A4 Cyber Security Awareness Posters-Social Engineering part 3Data Hops
Free A4 downloadable and printable Cyber Security, Social Engineering Safety and security Training Posters . Promote security awareness in the home or workplace. Lock them Out From training providers datahops.com
GraphRAG for Life Science to increase LLM accuracyTomaz Bratanic
GraphRAG for life science domain, where you retriever information from biomedical knowledge graphs using LLMs to increase the accuracy and performance of generated answers
zkStudyClub - LatticeFold: A Lattice-based Folding Scheme and its Application...Alex Pruden
Folding is a recent technique for building efficient recursive SNARKs. Several elegant folding protocols have been proposed, such as Nova, Supernova, Hypernova, Protostar, and others. However, all of them rely on an additively homomorphic commitment scheme based on discrete log, and are therefore not post-quantum secure. In this work we present LatticeFold, the first lattice-based folding protocol based on the Module SIS problem. This folding protocol naturally leads to an efficient recursive lattice-based SNARK and an efficient PCD scheme. LatticeFold supports folding low-degree relations, such as R1CS, as well as high-degree relations, such as CCS. The key challenge is to construct a secure folding protocol that works with the Ajtai commitment scheme. The difficulty, is ensuring that extracted witnesses are low norm through many rounds of folding. We present a novel technique using the sumcheck protocol to ensure that extracted witnesses are always low norm no matter how many rounds of folding are used. Our evaluation of the final proof system suggests that it is as performant as Hypernova, while providing post-quantum security.
Paper Link: https://eprint.iacr.org/2024/257
zkStudyClub - LatticeFold: A Lattice-based Folding Scheme and its Application...
Theory simulation fabrication and testing of double negative an
1. THEORY, SIMULATION, FABRICATION AND TESTING OF DOUBLE NEGATIVE
AND EPSILON NEAR ZERO METAMATERIALS FOR MICROWAVE APPLICATIONS
A thesis
Presented to the faculty of California Polytechnic State University,
San Luis Obispo
In Partial Fulfillment
of the Requirements for the Degree
Master of Science in Electrical Engineering
By
Neil Patel
June 2008
2. AUTHORIZATION FOR REPRODUCTION OF MASTER'S THESIS
I grant permission for the reproduction ofthis thesis or any ofits parts, without
further authorization from me.
~--
Neil Patel
Date
3. APPROVAL PAGE
THEORY, SIMULATION, FABRlCATION AND TESTING OFTITLE:
DOUBLE NEGATIVE AND EPSILON NEAR ZERO
:METAMATERlALS FOR MICROWAVE APPLICATIONS
AUTHOR: Neil Patel
DATE June 6th
2008
SUBMITTED:
Date
Date Dr. Denn.i!! Derickson
: :VM tL. G2 0 () ~ ~~:..>-"'/ -~~~~'--'--'-'~--==--.,r--- _"";>~~'_ _.L/~-,,,-- _
Date Dr. Xiaornin Jin
4. ABSTRACT
THEORY, SIMULATION, FABRICATION AND TESTING OF DOUBLE NEGATIVE
AND EPSILON NEAR ZERO METAMATERIALS FOR MICROWAVE APPLICATIONS
Neil Patel
Electrical Engineering Department
Master of Science
Natural structures exhibiting simultaneous negative bulk permittivity and permeability have
not yet been discovered. However, research interest over the past five years has grown
with the proposition that artificial structures exhibiting these properties are realizable us
ing specially-designed metallic inclusions embedded in host dielectric bodies. A periodic
structure of metallic inclusions much smaller than the guided wavelength and embedded in
a host dielectric medium is known in the physics and microwave communities as a "meta
material". Such frequency-dependent effectively homogeneous materials may be designed
to exhibit negative permeability and permittivity at certain frequencies. As predicted by
electromagnetic theory, such negative index or "left-handed" metamaterials are shown to
have unique filtering properties and exhibit negative refraction and "backward wave" prop
agation. The "backward wave" phenomenon describes the anti-parallel nature of phase
velocity and group velocity in a negative index metamaterial and can be additionally char
acterized in vector theory using the left hand rule. Additionally, "epsilon-near zero" (ENZ)
metamaterials are characterized by a bulk permittivity equal to zero. Applications include
focusing radiation emitted by small apertures.
5. This thesis provides the theory for metamaterial structures supported by simulations
conducted with the commercial finite element method solver: Ansoft HFSS. Metallic in
clusions such as the split ring resonator structure (SRR), S-shaped split ring resonator (S
SRR), wire rod and capacitively loaded strip (CLS) are presented analytically and simulated
in HFSS. Metamaterial structures designed to exhibit left-handed behavior in the X-band
frequency region are simulated for frequency-dependent transmission, reflection and refrac
tive properties. A test configuration for measuring a metamaterial slab's match to free space
is proposed and constructed. Additionally a prism design and test plan geared for anechoic
chamber testing and refraction measurement is proposed and built. Simulated inclusions are
fabricated on FR-4 epoxy laminate boards, combined to form metamaterial structures, and
tested in the Cal Poly Anechoic chamber. Results show that transmission properties match
closely with HFSS simulations. Prism metamaterial testing shows that negative refraction
is visible in the 8 to 9 GHz region. A modified form of the Nicolson Ross-Weir method for
parameter extraction using S-parameter data is shown to provide an initial approximation
for the permeability and permittivity of the structure under test. Finally, both negative and
zero-index metamaterials are analyzed in HFSS simulations to improve the directivity of
EM radiation from sub-wavelength apertures. Epsilon-near zero metamaterials placed on
sub-wavelength apertures are shown to improve directivity by two fold in the far-field at
design frequencies.
6. ACKNOWLEDGMENTS
I would like to Acknowledge Professor Dean Arakaki, whose guidance was instrumen
tal in the completion of this project. Without his willingness to donate time and effort in
obtaining grants for materials and the construction of the Cal Poly Anechoic Chamber this
project would not have been possible. I would also like to acknowledge committee members
Dr. Dennis Derickson and Dr. Xiaomin Jin for the time taken out of their busy schedules to
give project feedback and learn about the exciting field of metamaterials. Finally, I would
like to acknowledge my parents Ajay and Shama Patel; without their love and support the
past six years, my completion of a Master of Science in Electrical Engineering would not
have been possible.
7. Contents
List of Figures x
List of Tables xvi
1 Introduction 1
1.1 Metamaterials............. 1
1.1.1 Basic plane wave theory ... 2
1.2 Double Negative Index metamaterials 3
2 Parameter Extraction 9
2.1 Nicolson-Ross-Weir method . . . . . . . . . . . . . . . . . . . 9
2.1.1 Complex propagation constant of the material under test 12
2.1.2 Intrinsic parameters for a Coaxial Waveguide . . . . . . 13
2.1.3 Intrinsic parameters for a Rectangular Waveguide. . . . 14
2.2 An implementation of the NRW method pertaining to Double Negative Metamaterials 15
2.3 Divergence in the Nicolson-Ross-Weir equations 18
3 The Split Ring Resonator Inclusion 20
3.1 Split Ring Resonators and Permeablility . 20
3.1.1 Array of cylinders . 21
3.1.2 Capacitive array of sheets wound on cylinders. 23
3.1.3 Split ring resonator . 25
3.2 Circular SRR inclusion simulation in Ansoft HFSS 27
3.2.1 Unit cell synthesis in HFSS 27
3.2.2 Simulation results . 30
3.2.3 Parameter variations . 30
3.3 Square / Quadrilateral SRR inclusion simulation in Ansoft HFSS 34
3.3.1 Unit cell synthesis in HFSS 34
3.3.2 Parameter variations . 34
4 Wire and strip structures to realize negative permittivity 38
4.1 Thin wire structures . 39
4.2 Capacitively loaded strips (CLS) . 43
Vll
9. CONTENTS ix
12 Application: Directivity and Power Enhancement through sub-wavelength apertures 113
12.1 Theory. . . . . . . . . . 113
12.2 HFSS simulations. . . . . . . . . . . . . . . . . . . . . . . . . 115
12.2.1 Ideal simulations . . . . . . . . . . . . . . . . . . . . . 115
12.2.2 MetaWc inclusions embedded in exit face dielectric slab 121
13 Conclusions 130
A Matlab Code 132
A.l Theoretical simulation of circular split ring resonator (SRR) 132
A.2 Theoretical simulation of S-shaped split ring resonator (SRR) . . . 134
A.3 Parameter extraction using Ziolkoswki's modified NRW relations 136
AA Parameter extraction using Chen et al's modified NRW relations 139
B Analysis of Project Design 142
B.l Summary of Functional Requirements 142
B.2 Primary constraints . . . 142
B.3 Economic . . . . . . . . 143
B.3.1 Bill of Materials 143
B.4 Environmental. . 143
B.5 Manufacturability 144
B.6 Sustainability . . 144
B.7 Ethical...... 144
B.8 Health and safetey . 144
B.9 Social and political 144
B.lO Development 144
Bibliography 146
10. List of Figures
1.1 Current sheet at x = Xo radiates into a left handed medium Source: D.R.Smith,
Duke University. 4
1.2 Depiction of refraction according to Snell's law. Negative refractive materials show
refraction on the other side of the normal. Snell's law is clearly preserved but the
angle for 82 is negative. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ., 6
1.3 Refraction in a slab of left-handedlDouble negative material. The negative refractive
index causes the bending of rays to negative angles of the surface normal. The
diverging beams of a point source convege back towards a focal point. The first
focal point may form inside the slab if the material has sufficient thickness. .... 6
1.4 Simulation in Ansoft HFSS of a parallel plate waveguide. The direction of phase
velocity is shown with arrows. It can be seen in increasing the phase from 0° to
1800 that the phase velocity is opposite in the middle material is opposite to the
materials on either end. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 8
1.5 Simulation in Ansoft HFSS of the lens/negative refractive attributes of double neg
ativelleft handed media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ., 8
2.1 A filled waveguide undergoing excitation encounters multiple reflections at the air
sample interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ., 10
3.1 An array of metallic cylinders with an external magnetic field applied parallel to the
cylinders. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 21
3.2 The cylinders are now seen to have an internal structure. The sheets are wound in
a split ring fashion in such a way that current cannot flow freely. However, if the
distance, d is small enough, current may be induced. An increase in capacitance
between sheets relates to an increase in current. Reference: [17] 23
3.3 A thin flat disk shaped split ring resonator. . . . . . . . . . . . . . . . . . . . . .. 25
3.4 A circular split ring resonator with the variables: a=10mm, c=lmm, d=O.lmm,
l=2mm and r=2mm is evaluated in Matlab using the effective permeability relation
(3.16) on the left. The equation predicts a resonance in permeability at approxi
mately 13.5GHz. HFSS simulations to obtain S-paramaters and subsequent para-
mater extraction predicts a resonance in the real part of the permeability at 11GHz
(right plot). HFSS simulations of a circular SRR are presented in more detail in
section 3.2. 27
3.5 Outline of a complete metamaterial slab. . . . . . . . . . . . . . . . . . . . . . .. 28
x
11. LIST OF FIGURES xi
3.6 Single metamaterial cell PECIPMC waveguide configuration in HFSS. The wave-
port integration lines are shown. PECIPMC faces are also indicated. . . . . . . .. 29
3.7 S-paramaters obtained from HFSS of a circular SRR with parameters: r = 1.4mm,
trace width = 0.5mm, gap width = O.1mm, lattice spacing (dielectric spacing) =
1mm and substrate dielectric permittivity = 2.2. . . . . . . . . . . . . . . . . . .. 31
3.8 Resonant Frequency of circular SRR for multiple outer radius lengths. . . . . . .. 32
3.9 Resonant Frequency of circular SRR for varying substrate dielectric constants. SRR
outer radius kept constant at 2.5mm. Trace width is 0.5mm. Gap sizing is O.lmm.
Unit cell boundaries unchanged at 5mm x 5mm with a dielectric height of 1mm. .. 33
3.10 Resonant Frequency of circular SRR for varying copper trace widths. SRR outer ra
dius kept constant at 4.0mm. Gap sizing is O.lmm. Unit cell boundaries unchanged
at 5mm x 5mm with a dielectric height of 1mm. The Dielectric is Rogers Duroid
8500 tr=2.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 33
3.11 Resonant Frequency of circular SRR for varying gap widths. SRR outer radius kept
constant at 4.0mm. Trace width is 0.5mm. Unit cell boundaries unchanged at 5mm
x 5mm with a dielectric height of 1mm. The Dielectric is Rogers Duroid 8500 tr=2.2 34
3.12 Single unit cell of a square SRR in the PECIPMC waveguide configuration for sim
ulation in HFSS.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.13 Resonant Frequency of a square SRR with multiple outer radius lengths. 36
3.14 Resonant Frequency of square SRR for varying copper trace widths. 36
3.15 Resonant Frequency of square SRR for varying gap widths. 37
4.1 HFSS structure example for an array of thin wire rods. ... 41
4.2 Transmission results from a 3x3 wire rod array simulated in HFSS. Cylinder radius
= 0.2mm. Lattice spacing, a = 5mm, and the dielectric medium is air. Resonance is
seen at 20GHz. The location of the plasma frequency is thus at wp = 20GHz. 42
4.3 Unit cell consisting of 2x2 array of capacitive loaded strips in PECIPMC waveguide
configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 44
4.4 Simulated S-parameter data on a 2x2 array of CLS structures. The low resonance
is at 4.4Ghz and the plasma frequency where evanescent modes no longer dominate
is 25.7GHz. CLS height (h) = 9.6mm and capacitive strip width (w) = 4.5mm.
Microstrip width = O.4mm. Lattice spacing (a) = 2.5mm. 44
5.1 2D and 3D diagrams of S-shaped SRR structure.. . . . . 47
5.2 A synthesized S-SRR unit cell in HFSS. Copper thickness is 1 oz (0.2mm). F1 = F2
in this case. . . . . . . . . . . . . . . . . . . . . . . . . . . 52
5.3 Resonant Frequency of S-SRR for varying inclusion heights. . . . . . . . . . . .. 53
5.4 Resonant Frequency of S-SRR for varying inclusion widths. 54
5.5 Resonant Frequency of S-SRR for varying dielectric permittivities. SRR height =
6mm, SRR width = 4mm, copper width = 0.5mm, spacing between mirrored S
shaped resonators (d) = 1.5mm, distsance between S-shape pairs, 1= 2.5mm. Unit
cell height (a) = lOmm and width (b) = 7mm. . " 54
5.6 Divergence/resonance simulation in matlab for an S-SRR unit cell with height=7.5mm,
width=4mm, copper width = 0.5mm, distance between mirrored rings=0.5mm, S
SRR pair seperation, l=lmm, unit cell: lOmmx5mm. . . . . . . . . . . . . . . .. 55
12. xiiLIST OF FIGURES
6.1 A unit cell with a circular SRR and thin wire strip. The boundaries are 10mm x
lOmm in the X and Y directions. The separation between the SRR and wire strip is
1mm. SRR outer radius is 3mm with a copper strip width of Imm and gap width of
0.2mm. 58
6.2 Resonance shown in scattering parameters at approximately 18Ghz. . . . . . .. 58
6.3 Extracted real part of (tr from S-parameters. The equations are used respectively. 59
6.4 Extracted real part of f.tr from S-parameters. . . . . . . . . . . . . . . . . . . .. 59
6.5 Extracted real part of the index of refraction and slab electrical thickness. .... 60
6.6 A unit cell with a square SRR and capacitively loaded strip. The boundaries are
210mils x 160mils in the X and Y directions. The separation between the Square
SRR and the CLS is 0.45mm. SRR outer radius is 50mils with a copper strip width
of 10mils and gap width of 5mils. Rogers Duroid, tr = 2.2 is used as the dielectric
substrate. 61
6.7 Resonance shown in scattering parameters at approximately 8GHz " 61
6.8 Extracted tr from S-parameters. The equations (2.29) (2.31) are used respectively. . 62
6.9 Extracted f.tr from S-parameters recorded through simulation of square SRRlCLS
unit cell. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 62
6.10 Extracted index of refraction and electrical thickness from S-parameters recorded
through simulation of square SRRJCLS unit cell. 63
6.11 Side view of the CLS 2x2 array unit cell in HFSS. h = 15.7mm, h=4.5mm, and
lattice spacing a = 5mm. The copper inclusions are embedded in an air box. . . .. 63
6.12 Extracted f.tr from S-parameters. The equation (2.28) is used for extraction. . . .. 64
6.13 Extracted tr from S-parameters recorded through the simulation of a 2x2 CLS array. 65
6.14 Extracted index of refraction from S-parameters recorded through simulation of a
2x2 CLS array. 65
7.1 Standard square SRR unit cell. 67
7.2 Parametric Analysis results for square SRR on FR4 substrate with 'a' varied from
70 to 150 mils in 5 mil steps. 'c' = lOmils 'd' = 8mils and t=62 mils. . . . . . . .. 68
7.3 Insertion loss and forward transmission for an SRR on FR4 unit cell with a = 90 mils. 69
7.4 Insertion loss and forward transmission for an SRR on FR4 unit cell with a = 150
mils. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 69
7.5 Parametric Analysis results for square SRR on FR4 substrate with 'a' varied from
85 to 95 mils in 0.5 mil steps. 'c' = 10mils 'd' = 8mils and t=62 mils. 69
7.6 Insertion loss and forward transmission for an SRR on FR4 unit cell with a = 88 mils. 70
7.7 Standard S shaped SRR unit cell. . . . . . . . . . . . . . . . . . . . . . . . . . .. 71
7.8 Parametric Analysis results for S-shaped SRR on FR4 substrate with 'w' varied
from 5 to 7 mm in 0.1 mm steps. Constants: 'h'=3mm 'c'=0.5mm 'a'=lOmm
'b'=6.5mm 'd'=1.57mm, 'l'=2.362mm. 'd' = 8mils and t=62 mils. . . . . . . . .. 72
7.9 Measured S-paramters show resonance at 8.5GHz when 'w'=6.3mm . . . . . . .. 73
7.10 Final unit cell structure for the planar SRR-CLS metamaterial. The value of 'a'
found through parametrics is used. . . . . . . . . . . . . . . . . . . . . . . . . .. 74
7.11 Transmission simulation results for the SRR-CLS structure. Resonance is visible at
8.5GHz. . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
7.12 Final unit cell structure for the planar S-SRR metamaterial. . . . . . . . . . . . .. 75
13. xiiiLIST OF FIGURES
7.13 Transmission simulation results for the S-SRR structure. Resonance is visible at
8.5GHz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 75
8.1 HFSS simulation setup for prism refraction setup. A waveport is used as an input.
Radiation boundaries allow waves to radiate into the far-field. Top-down view does
not show depth in Z-direction (1 Omm). . . . . . . . . . . . . . . . . . . . . . . ., 77
8.2 Prism outline indicating angles with respect to 0 degrees normalized to the prism
normal face. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ., 78
8.3 Normalized directivity simulations for ideal prism sample for varying ET and /-LT' 79
8.4 Normalized directivity with respect to the peak recorded value for a given frequency.
Peak directivity is visible at angles negative of the prism normal for frequencies
such as 7.8GHz, 8.2GHz, 8.5GHz and 9GHz. The prism is operating as a normal
right-hand material at 7GHz and 9.5GHz. . , 81
9.1 Dimensions for Metamaterial structure containing SRRJCLS and S-SRR inclusions 83
9.2 Typical S-SRR inclusion . . . . . . . . . . . . . . . . . . . . 84
9.3 Prism S-SRR structure . . . . . . . . . . . . . . . . . . . . . . . 85
9.4 Representation of an ideal prism with the required dimensions . . 85
9.5 Three S-SRRs in Y direction (left to right). Distance totals 1.9cm. 86
10.1 Block diagram for proposed testing of DNG metamaterials in the Anechoic Chamber. 89
10.2 Sideview of testsetup structure. . . . . . . . . . . . . . . . . . . . . . . . . . . .. 89
10.3 Foam board dimensions and square aperture for metamaterial slab placement. Meta-
material sample is embedded directly within an aperture in the foam board. .... 90
10.4 Top down view of antenna chamber looking specifically at the test and positioner
setup. . , 90
10.5 Horn antenna placed at the minimum distance to generate a plane wave. The maxi
mum extent of the radiation due to a beam angle of 30cm is shown to be 33cm. .. 92
10.6 Reflection readings for test fixture without foam board and absorbers, with foam
board/absorbers and with metal sheet in incidence path. . . . . . . . . . . . . . ., 93
10.7 Transmission measurements in free space with no metamaterial slab. Plots for setup
with/without foam board and absorbers. . . . . . . . . . . . . . . . . . . . . . .. 94
10.8 Transmission and reflection with square aperture in foam board blocked , 94
10.9 Transmission and reflection measurements to validate test setup after normalized
transmission calibration for free-space testing. . . . . . . . . . . . . . . . . . . .. 95
10.10Test setup in Anechoic chamber. Foam board has been removed to make both Rx
and Tx horn antennas visibile. . . . . . . . . .. 96
11.1 Measured slab transmission data compared to theoretical data predicted by HFSS. 99
11.2 Measured slab reflection data compared to reflection data predicted by HFSS. " 99
11.3 Graph showing the frequency shift in the transmission peak when changing the
thickness of 31 mil spacer boards to 62 mils. . . . . . . . . . . . . . . . . . . . .. 100
11.4 Extracted relative permeability and permittivity for the S-shaped transmission slab. 102
11.5 Extracted index of refraction for the S-shaped transmission slab. . . . . . . . . .. 102
11.6 Simulated and measured S12 phase data. The measured data e>lhibits phase noise in
the range from 9 to 9.8 GHz. . . . . . . . 103
11.7 Simulated and measured S11 phase data. 103
14. LIST OF FIGURES xiv
11.8 Simulated and measured insertion loss (Sll) data for SRRlCLS metamaterial slab. 104
11.9 Simulated and measured (S12) data for SRR/CLS metamaterial slab , 105
11.10Fabricated metamaterial prisms with S-SRR inclusions . . . . . . . . . . . . . .. 106
11.11Theoretical diagram of prism metamaterial sample with modified dimensions. The
normal angle is 26.56 degrees. All azimuthal measurements are taken with this
normal angle taken as 0 degrees. . . . . . . . . . . . . . . . . . . . . . . . . . ., 107
11.12Top down view diagram of modified prism. Diagram indicate reference normal
angle and directions of peak radiation for 2 frequencies, one with left hand wave
propagation and the other showing right hand wave propagation. . . . . . . . . .. 108
11.13Index of refraction obtained from prism experiment. 109
l1.l4Normalized power received for two frequencies. Negative refraction is clearly visi
ble at 8.4 GHz, while at lOGHz, the refraction clearly exhibits standard right handed
behavior.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 109
11.15Fabricated FR-4 only metamaterial prism used to test the ability of the test setup to
accurately measure the structure's index of refraction. . . . . . . 110
11.16Index of refraction obtained from a FR-4 only prism. . . . . . . 111
11.17 Normalized power received at 8.5GHz for the FR-4 only prism. . III
12.1 Ideal Ray diagrams showing the impact of diffraction due to a sub-wavelength aper
ture in 4 configurations: I)No exit or entrance metamaterial slab, 2)Exit only slab
with k >> ko. 3)Exit only slab with k << ko and 4)Entrance and exit slab
withk << ko " 114
12.2 Top down view of simulation setup in HFSS. Parameters such as aperture size, exit
slab thickness and air box size/depth may be varied with the use of variables. De
fault settings are aperture size = 5rrun x 5mm. Slab thickness = 54mm and air box
depth in the z direction = 1Omm. A circle has been drawn around the setup to re
semble the far field sphere set by HFSS. The goal is to maximize directivity and
gain in the ¢ = 900 direction. . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 116
12.3 Block diagram for proposed testing of DNG metamaterials in the Anechoic Chamber. 119
12.4 Sideview of testsetup structure. . . . . . . . . . . . . . . . . . . . . . . . . . . .. 119
12.5 Thin wire rods embedded in exit aperture slab. . . . . . . . . . . . . . . . . . . .. 122
12.6 Beam directivity in the azimuthal plane from a sub-wavelength aperture covered
with a slab consisting of thin rod structures. Slab thickness is 22mm. . . . . . . .. 122
12.7 S-shaped split ring resonators embedded in exit aperture slab. . . . . . . . . . . .. 123
12.8 Beam directivity in the azimuthal plane from a sub-wavelength aperture covered
with a slab consisting of S-shaped resonators. Slab thickness is 54mm. . . . . . .. 124
12.9 Gain Enhancement for a S-SRR slab placed on the exit face of a sub-wavelength
aperture in comparison to the case that no slab is present. . . . . . . . . . . . . .. 125
12.10Grid mesh unit cell designed for a plasma frequency at approximately 8GHz. Lattice
paramater a = 5.0mm and copper strip width c = 0.2mm. Spacing =6mm. ..... 126
12.11 Transmission simulation results for grid mesh structure shown in Figure 12.12. A
plasma resonance is seen at approximately 8GHz. In this region it is expected that
Cr' and n approaches zero and hence k << 1. 126
12.12Grid mesh structures embedded on the exit face of the sub-wavelength aperture in
HFSS. There are 3 lattice elements in the Y direction leading to a slab thickness of
18mm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 127
15. LIST OF FIGURES xv
12.13Directivity when Grid mesh is placed on the exit face of the aperture. Far field plots
are presented for several frequencies near the plasma resonance of the grid mesh
structure.
12.14Gain Enhancement for a S-SRR slab placed on the exit face of a sub-wavelength
aperture in comparison to the case that no slab is present. . . . . . . . . . . . . ..
128
129
16. List of Tables
1.1 Sign rules of the refraction index . . . . . . . . . . . . . . . . . . . . . . . . . .. 5
1.2 Microwave Permittivity and Permeability characteristics of homogeneous metama
terials. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1 HFSS simulation results for multiple circular SRR unit cell dimensions. 31
4.1 Theoretical and simulated plasma frequencies for thin 3x3 wire rod structure unit
cells of various wire radii and lattice spacings in an air medium. 42
4.2 Simulated resonant and plasma frequencies for a 2x2 array of CLS structures in air
with lattice spacing, a = 2.5mm, height=9.6mm and microstrip width=O.4mm. The
capacitive load widths on each end are varied. . . . . . . . . . . . . . . . . . . .. 45
5.1 HFSS simulation results for varying unit cell dimensions. Results show the S-SRR
equations provide only a very rough approximation and that HFSS simulations are
absolutely necessary to characterize a SRR inclusion. . . . . . . . . . . . . . . .. 52
5.2 HFSS simulation results for varying loop ratios to alter the two resonance frequencies. 55
5.3 Summary of the transmission, permittivity and permeability characteristics of the
inclusions introduced in this thesis. . . . . . . . . . 56
7.1 Square SRR parameters. . . . . . . . . . . . . . . 67
7.2 Comparison of various transmission test results for a SRR-CLS unit cell where verti
cal electrical spacing between the CLS and SRR inclusions is varied. Measurements
taken at the resonance frequency fo 70
7.3 S-SRR parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 72
8.1 Table showing agreement between theoretical calculations for n using n = JEr/-Lt·
and simulated results. Agreement is accurate in regions where Inl 2: 1. . . . . . .. 79
8.2 Table showing frequency dependent index of refraction obtained from far field ra
diation pattern simulations of S-shaped SRR metamaterial prism structure in HFSS. 80
12.1 Table shows relationship between exit face metamaterial /-Lt·, Er and directivity. As
permeability and permittivity is reduced, k < aand the directivity is enhanced. .. 117
12.2 Table shows relationship between aperture width, directivity and Gain. HFSS simu
lation results at 8.5GHz are obtained using a homogeneous ideal slab with zero loss
tangent 8, Er = 0.1 and /-Lr = 0.1. The slab thickness was held constant at 54mm 120
B.l Bill of materials for products ordered from Current Composites. 143
XVI
17. LIST OF TABLES xvii
B.2 Bill of materials for products ordered from the PCB company. 143
18. Chapter 1
Introduction
1.1 Metamaterials
Metamaterials are inherently artificial materials, not found in nature and which yield interesting
electromagnetic responses. Jagadis Chock in 1898 constructed the first metarnaterial out of artificial
chiral elements [1]. Lindman, in 1914 made artificial chiral media by embedding many randomly
oriented small wire helices in the host medium [2]. Kock in 1948 [3] created microwave lenses
by embedding metallic strips, wires and disks periodically in order to tailor the artificial media's
refractive index. As fabrication methods improve, the inclusions (artificial structures) embedded in
the host medium reduce in size.
Electromagnetic waves interact with inclusions in the host medium, induce electric and magnetic
moments, which in turn affect the material's transmission capabilities and material parameters such
as permeability and permittivity. When characterizing the permittivity (E) and permeability (J-L)
of a metamaterial, one must characterize the structure as homogeneous. If one considers a single
inclusion as part of a unit cell periodically embedded within the host medium, its size p must be
less than a quarter of the incident radiation wavelength: p < ~. This homogeneity relation is a
rule of thumb condition. The relation is commonly used in distinguishing lumped components from
quasi-lumped components, (~ < p < ~) and distributed components: (p > ~). This condition
ensures that refractive phenomena inherent in homogeneous materials dominate over scattering and
1
19. 1.1 Metamaterials 2
diffusion effects. The electromagnetic radiation is essentially unaware of the lattice structure in the
host medium and maintains field uniformity in the direction of propagation within the structure.
1.1.1 Basic plane wave theory
A plane wave can be described in terms of three vectors: Electromagnetic field vectors £ and ii, as
well as the wave number vector in the direction of propagation, k. Mathematically, the plane wave
may be represented as:
E(r) = EoeJ(kr-wt)
(1.1)
H(r) = Hoej(kr-wt)
In a linear, homogeneous, isotropic, dispersionless medium such as vacuum, there is no free
charge or current present and hence Maxwell's Equations of free space are:
7·£=0
7·.8=0
(1.2)
~ 0.8
7 x E =-at
~ o£
7 x B = f-LoEo at
The above relations for Maxwell's equations in differential form can be represented in the Gaus
sian system. Defining the electric displacement field D = EE and B = f-LH, the Maxwell Equations
can be stated as:
~ 0.8 f-L1'J-Lo off7 x E = - - = ----
ot otC
(1.3)
.8 E1'EO o£7x-=-
f-Lo C ot
Mathematical equations for a plane wave may be substituted into the above Gaussian system
20. 1.2 Double Negative Index metamaterials 3
Maxwell Equations to yield:
k x E = wp,if
(1.4)
~ ~ 1 ~
k x H = --p,E
w
Thus, the curl of E and if is proportional to the cross product of the k vector and the E or if
field. These vectors follow the right hand rule. Power flow is described by the Poynting Vector:
(1.5)
In the usual case of plane wave propagation where the right-hand rule may be applied to a wave
with component k parallel to the direction of power flow, E and p, are positive. Finally, a positive
refraction index may then be realized using the standard relation:
n=~ (1.6)
1.2 Double Negative Index metamaterials
In 1967, physicist VG. Veselago from the Lebedjev Physical institute of Moscow theoretically in
vestigated plane wave propagation in a material whose permittivity and permeability were assumed
negative [4]. With both parameters negative, equation (1.4) shows that the propagation vector kre
verses direction and the set of three vectors: k, E, if follow a left-hand rule. Hence double negative
materials are also known as Left-handed materials. As the k vector has reversed direction, the
phase velocity is now opposite to power flow (denoted by the Poynting vector). The refractive index
of the material must also be considered. The square root in (1.6) is not violated if both permeability
and permittivity are negative. However, refraction is also phase sensitive [4],thus n becomes neg
ative. A separate argument may be made for the sign choice in the index of refraction calculation.
In [7], it is pointed out that one cannot assume n < 0 for a double negative index metamaterial.
21. 41.2 Double Negative Index metamaterials
However, the constraint that the source must do positive work on the external fields may be made.
With this constraint in mind, a current sheet radiating into a left-handed medium may be analyzed.
A current sheet is depicted in Figure 1.1. The density of the current sheet polarized in the z direction
is:
(1.7)
where Jo is the strength of the surface cunent density, {3 is the rate of linear phase change in
the x direction. The direction of current flow is assumed to be z. The direction of phase variation is
along x. Note the anti-parallel nature of the wave vector k and the Poynting vector S. Using 0 as
the oscillation frequency of the source current, [7] derives the current sheet power as:
p = OW = -~ 1j *E(x, O)dx = nJ!.../6 (1.8)
2 v en
From (1.8), positive power is needed for positive work to be done by the source on the surround
ing fields. In the case when /l < 0, the index of refraction, n must also be less than zero (n < 0).
For radiation in a right-handed medium where /l > 0, the index of refraction n, must also be greater
than zero (n > 0).
Figure 1.1 Current sheet at x = XQ radiates into a left handed medium Source: D.R.Smith,
Duke University.
22. 51.2 Double Negative Index metamaterials
Table 1.1 depicts the sign rules for material refractive index while Table 1.2 introduces some
basic properties and names for materials for various combinations of penneability and pennittivity.
Er > 0 C1' < 0
f-LT > 0 positive imaginary
f-Lr < 0 imaginary negative
Table 1.1 Sign rules of the refraction index
E > 0, f-L > 0 C < 0, f-L > 0 C > 0, f-L < 0 C < 0, f-L < 0
- Forward wave - Metal like - Ferrimagnetic material - Left-handed medium
propagation characteristics at characteristics - Backward-wave
optical frequencies propagation
- Evanescent waves - Evanescent waves - Re(n) < 0
Table 1.2 Microwave Permittivity and Penneability characteristics of homogeneous meta
materials.
Snell's Law is commonly used to describe the relationship between angles of incidence and
refraction, when referring to light or electromagnetic waves passing through a planar boundary
between two passive isotropic media. If n1 and 81 describe the refractive index and incidence angle
of the incoming wave in the first medium, while n2 and 82 refer to the second medium, Snell's law
is represented by:
(1.9)
If nl is negative, then:
= sin-1
(~ < 0)
(1.10)
23. 61.2 Double Negative Index metamaterials
where ~ substitutes for the argument of the arcsine function. Note that the angle of incidence
with respect to the normal is presumed to be 00 < e1 < 900
. Refer to Figure 1.2.
Normal
01 - air mterface
Refractio. du to rialltRefracno. d.e
un materialto left b.d
material
Figure 1.2 Depiction of refraction according to Snell's law. Negative refractive materials
show refraction on the other side of the normal. Snell's law is clearly preserved but the
angle for ez is negative.
refractioD iD right handed-media
~ __--' V-
rerraction in left-handed
media K-> Diredwn or
prop
Figure 1.3 Refraction in a slab of left-handed/Double negative material. The negative
refractive index causes the bending of rays to negative angles of the surface normal. The
diverging beams of a point source convege back towards a focal point. The first focal
point may form inside the slab if the material has sufficient thickness.
24. 71.2 Double Negative Index metamaterials
Backward wave propagation simulation
The group velocity Vg and phase velocity Vp must be considered when looking at the backward
wave propagation phenomenon of negative index metamaterials. The group velocity indicates ve
locity at which the wave envelope or wave ampl.itude modulates. It best describes the rate at which
information is conveyed along a wave. The phase velocity of a wave is the velocity at which the
phase of one frequency component of the wave travels. The group velocity indicates the veloctiy of
the collective wave or wave packet while the phase velocity indicates the velocity of the wave nodes
i.e crests. Velocity is a vector, hence, has both a magnitude and direction associated with it. The
Poynting vector as previously described denotes the group velocity and is anti-parallel to the phase
velocity in a left-handed (double-negative) medium. A simulation is conducted in HFSS to show
this phenomenon (see Figure 1.4) in a parallel plate waveguide configuration. The top and bottom
transparent faces are defined as perfect E planes to approximate a parallel plate setup. Both ends
have waveports to introduce the radiation. The waveguide is divided into 3 sections. The first and
last sections are a free space material with tr = +1, /-Lr' = +1. The middle material is defined with
bulk parameters tr' = -1, /-Lr = -1.
Lens simulation
HFSS is used to simulate the lens focusing characteristics of double negative media. Two slabs are
placed adjacent to each other. A cylindrical source with propagation vector I polarized in the Z
direction is situated within the right handed medium (tr = 4.4, J.Lr = 1) while radiation boundaries
are placed around the left handed medium with bulk parameters: tr = -1, /-Lr = -1. Simulation
occurs at 8.5GHz. As seen in Figure 1.5 , a focal point or image is seen within the left-handed
medium.
25. 81.2 Double Negative Index metamaterials
tbe'" = 0 degrees
Yp
Ibera =42 degrees
rbela = 127 degrees
rbeta = 144
degrees
I. F11l1d[VI.]
s. !te·OO'
2 ~ ·003
7133" 3
9.UZ7C'·OOZ
5 i"t e·OO:
3.1Sa.,.e.-oo.l
18S4.....
1. e 15~;e·oo-2'
& 11.1~t.·:'.H
, 512'8e'OOl
2: fH6(i~'OOl
Figure 1.4 Simulation in Ansoft HFSS of a parallel plate waveguide. The direction of
phase velocity is shown with arrows. It can be seen in increasing the phase from 0° to
180° that the phase velocity is opposite in the middle material is opposite to the materials
on either end.
1x
source
c)'lindrlcal Focal point/image
wa'e
Len banded medium
Figure 1.5 Simulation in Ansoft HFSS of the lens/negative refractive attributes of double
negative/left handed media.
26. Chapter 2
Parameter Extraction
2.1 Nicolson-Ross-Weir method
The equations published by Nicolson, Ross and Weir [12] enable the calculation of the complex per
mittivity and permeability of a material sample (Figure 2.1) from the measured S-parameters. The
correlation between S-parameters and material properties is derived here by considering multiple
reflections of a unit amplitude wave incident upon the air-sample interfaces within the waveguide.
The multiple reflections at the air-sample interfaces within a filled waveguide are shown below:
When a wave is incident upon the air-sample interface, partial reflection and transmission oc
curs. The partial reflection is accounted for by and the transmitted portion. Partial reflection and
transmission occurs again when the wave strikes the sample-air interface. Summing the reflections
occurring at the first sample interface yields:
'T' r -j2"(d T 'T' r2r -j4"(drin= r1+ T12.121 3e + 12.1213 2e + ....
00 (2.1)
= r1 +T12T21r3e-j2r,1> L r~r3e-2jn8
n=O
(2.2)
27. 2.1 Nicolson-Ross-Weir method 10
AIR I MATERIAL AIR II
------01----+121 T Tlie
-j8
32
Figure 2.1 A filled waveguide undergoing excitation encounters multiple reflections at
the air-sample interfaces.
One can obtain the S parameter equivalent for fin and 8 11 through some manipulation. Let
Z -1
f1 = Z + 1
T12 = 1 + f2
(2.3)
T21 = 1 +f 1
_ f 1 (1 - z2)
811 = fin = 2 2
1- f1z
Note that the relations z2 = e-j2B and e= "jd are used in (2.3). The lower-case z in this case is
the propagation factor through the sample. The expression for 8 11 is then found by substituting the
terms in (2.3) into (2.2). Next, the sum of all wave components transmitted completely through the
28. 2.1 Nicolson-Ross- Weir method 11
material sample may be obtained:
()
rr - T T e- j () " rn rn ej (2n+1)().L out - 32 21, ~ 2 3
n=O (2.4)
()
, ~32~21e-J
Total Transmitted = r r - '2()
1 - 2 3e J
(2.5)
The values of z (complex transmission constant, also referenced as ~ in some papers) and r 1
remain unknown at this point. Sum and difference properties of S-parameters are implemented as
follows:
(2.6)
The product of V1 and V2 is therefore:
(2.7)
Z2 - r 2
1
1 - r 2
1
z2
The difference of V2 and Vi is:
= 2811 (2.8)
2r1 (1 - z2)
1 - riz2
29. 2.1 Nicolson-Ross-Weir method 12
Let X = l
Vi~~2 ,and using (2.7) and (2.8) one can find X in terms of f 1:
(2.9)
Now f 1 may be determined in terms of X using the quadratic formula -b±~:
2flX = 1 + fi
(2.10)fi - 2f1X + 1 = 0
f 1 = X ± JX2-1
The choice of sign in (2.10) should yield If11 .s 1. Using fl, 811 , and 821, one can determine
the value of the complex exponential z.
V1 - f 1 = 821 + 811 - f 1
_ f 1 (1 - z2) + z (1 - fi) _ f
(2.11)- I-f2z2 1-f2
z2 1
1 1
f 1 - fi z2 + z - fiz - f 1 + fr z2
1 - fiz2
_ V; f _ 1 - zf1 + zfr - fi
(2.12)1 1 1 - 1 _ f2 2z1
(1 - fi) (z - z2fi)
1 - f 2
1z2
z(1-zf1) (2.13)
1 - zf1
=z
2.1.1 Complex propagation constant of the material under test
The complex exponential transmission term z relates to the propagation constant of the material.
Using the z term, one may calculate the complex propagation constant (1) of the material. The
method used is known as de Moivre's Theorem and may be represented as:
30. 2.1 Nicolson-Ross-Weir method 13
(cosx + jsinxt = cos (nx) + jsin (nx)
(2.14)
Noting as explained earlier, that z2 = e-
j2B
where B= ,d, the complex propagation constant
may be found as follows:
= cos(nB) + jsin(nB)
=(cos(B) + jsin(B)t
1 (2.15)
- = (cos(B) + jsin(B))-n
zn
~ = cosB + jsinB = e'Yd
In (1)
z
= ,d
1In (1) =,
The variable din (2.15) is the sample thickness. Knowledge of the sample thickness, complex
propagation constant and characteristic impedance of a filled waveguide allow one to determine
the complex permittivity and permeability of a material. However, exact expressions for the per
meability and permittivity of these materials depend on the fundamental propagation mode in the
waveguide and the sample's intrinsic impedance. A rectangular waveguide and coaxial line are
discussed here. The coaxial line was used by Nicolson and Ross to verify the NRW method to
obtain the intrinsic properties of a material. In the next section, a discussion of the NRW method as
pertaining to double negative index metamaterials is analyzed.
2.1.2 Intrinsic parameters for a Coaxial Waveguide
In a lossless coaxial waveguide, the fundamental mode of propagation is the TEM mode. The
normalized impedance of the filled line section is the same as that of an infinitely long material in
31. 2.1 Nicolson-Ross-Weir method 14
freespace.
'r
Z == Zinfinite d = (2.16)
Erri
(2.17)
Refractive index: N = JErttr
(2.18)
./Ao
=-J
21l'
The material's complex permittivity and pelmeability are calculated by combining (2.16), (2.17)
and (2.18):
Mr=N·Z
(2.19)
N
Er = Z
2.1.3 Intrinsic parameters for a Rectangular Waveguide
In a rectangular waveguide, the guided wavelength differs from the free space value according to
the equation [33]:
(2.20)
The cutoff wavelength is denoted as Ac while the guided wavelength is Ag. In the T ElO mode,
the cutoff wavelength equals twice the longest transverse dimension of the waveguide. Equations
32. 2.2 An implementation of the NRW method pertaining to Double Negative Metamaterials 15
for the waveguide are shown below for air filled waveguide and sample filled waveguide:
Zai1' = {iii Ag
V~Aa
.27rf /-L1'/-La
Zsample = J - - (2.21)
{guide
2 (27r) 2
{guide = {+ A
c
The normalized characteristic impedance Z may be found using the air filled and sampled filled
characteristic impedances. This normalized characteristic impedance is the capitalized Z present in
(2.3).
(2.22)
Now one may solve for the relative permeability and permittivity of the filled rectangular waveg
uide:
Z~
{guide A
1/ - 0
,...,1' - .21T
J AO
2
2 27r (2.23)
{guide - A( c )
2.2 An implementation ofthe NRW method pertaining to Double Neg
ative Metamaterials
In [10], Ziolkowski briefly introduces the NRW method, but explains that the original form of the
analysis is unsuitable for calculating permittivites and permeabilities of DNG materials. The stan
dard extraction expressions are unsatisfactory in the frequency regions where the permittivity and
permeability resonances were expected. At these frequencies, a sharp transition between positive
and negative values is expected. The presence of square root values in (2.10) makes calculations
difficult in regions of permittivity and permeability resonance. While the sign preceding the square
33. 162.2 An implementation of the NRW method pertaining to Double Negative Metamaterials
root operation must yield 1f11 :S 1, the choice is difficult when S-parameters resonate and the choice
of sign may potentially bias the end result.
Using the steps outlined after (2.12), the following relations can be found:
V1 - f 1
Z=
1 - V1f1
(2.24)
Z - V2
similarly, f1 = IT
1 - ZV2
Note that Z is a complex exponential transmission term. From the above expressions, the fol
lowing may be obtained:
(1 - V1)(1 +fd1 - Z = -'---------'-==-~--'-
1 - f 1V1
1 +f 1
'f/ = - - (2.25)
1 - f 1
l+z 1-V2- _ . _
1-z 1+112
Note that for finite slab thicknesses, the transmission coefficient between two faces of the slab:
z = e-jw.fiiEd = e-jkd [12]. To simplify the analysis, one may take the Taylor expansion of this
exponential function and obtain:
Taylor series definition: f f(n)~a) (x - a)nwhere a=O in this case
n.
n=O
-jkd
(2.26)
z:::::! 1 - jkde-jkd - k2d2~ ...
2
k 2d2
z:::::! 1 - jkd - -2-"
For the simplification to be valid and the higher order functions of the Taylor series to be negli
gible, the product of the real part of the wave vector and the slab thickness must be less than unity.
Hence the slab must be "thin": Re(k) . d < 1. Therefore, the complex transmission term z may be
approximated as:
z:::::! 1 - jkd
(2.27)
34. 172.2 An implementation of the NRW method pertaining to Double Negative Metamaterials
The wave vector is calculated for each measurement frequency using the standard relation: k =
W .JE~JJ-r = kOVtr!Jr. Using this approximation, expressions for the wave vector k and permeability
!J may be obtained from (2.26). Expressions for V1 and V2 were developed earlier in terms of the
scattering parameters.
(2.28)
The permittivity and index of refraction may be obtained:
(2.29)
n = VtT!JT =
k
ko
An alternative equation for the relative permittivity tT may be obtained by finding the square of
the wave impedance:
(2.30)
While the above relation for permittivity is valid, it will be shown in Section 6.1 that resonance
features in permittivity are not as visible compared to the relation for permittivity presented by R.W
Ziolkowski (2.31) [10]. In the case of (2.29), results may not show a resonance as predicted by
the S-paran1eters [10]. Ziolkowski takes another approach to finding the relative permittivity of a
metarnaterial slab. The relation for SII for a slab of finite thickness d where the "thin" constraint
35. 2.3 Divergence in the Nicolson-Ross-Weir equations 18
real(k) . d < 1 holds:
jkd
Where z = e
(2.31)
solving for epsilon yields
.2Su
Er ;:::::; IJ,r + J kod
The above relation clearly shows that relative permittivity tracks the material's relative pelme
ability. Note that as Su goes to zero the value of the relative permeability dominates. This is
to be expected in double negative applications where the ISui parameter approaches zero while
peak transmission occurs in the frequency range of interest. However, the latter term must be large
enough to support the case where only permeability goes negative (i.e: SRR only media). Such a
metamaterial would require parameter extraction using a different set of relations.
2.3 Divergence in the Nicolson-Ross-Weir equations
It has been shown that the permittivity and permeability of a sample are uniquely related to the
reflection and transmission co-efficients. However it has been noted by several sources [14] [15]
that uncertainty is introduced into the numerical analysis when sample thicknesses approach a ~
multiple of the guided wavelength >.. Consider the case where the sample thickness d, is related
to the wavelength in the sample under test >'9 by d = n·;9. In this case, the transmission constant
z (T in some papers) approaches ±1. Hence, Z = ejkd
---t ±1. Examining equation (2.8) which
relates V2 - VI to Su, it is seen that the numerator and hence Su approaches zero. A divergence
or pole is seen in the variable X presented earlier. When Su approaches zero mainly due to the
influence of the structure thickness, steps must be taken to ensure that the electrical thickness does
not approach >./2 in the frequency range of interest. One solution is to use thin samples smaller than
the illuminating frequency's wavelength. While one may not expect the algorithm to be stable over
36. 192.3 Divergence in the Nicolson-Ross-Weir equations
a broad range of input frequencies, for the case of this project, the resonance frequency is restricted
to the X-band region; specifically 8.5 GHz. Hence, at 8.5 GHz the divergence problem in the NRW
method should be avoided. For this project as will be shown in chapter 9, a slab thickness of 2.6cm
was chosen. This is approximately 0.75; at 8.5 GHz and the maximum distance away from a A/2
multiple.
37. Chapter 3
The Split Ring Resonator Inclusion
It is important to consider the metallic inclusions needed to obtain negative permittivity and perme
ability using periodically structured metarnaterials. This chapter specifically deals with an inclusion
that responds to magnetic fields and hence has the potential to yield negative permeability.
3.1 Split Ring Resonators and Permeablility
J.B Pendry [17] hypothesizes that for periodic structures defined by a unit cell of characteristic
dimension p, a condition for the response of the system to electromagnetic excitation is as follows:
2Jrco
P«A=- (3.1)
w
In the event this condition does not hold, diffraction and refraction in the medium occur. The
relations between electric and magnetic field intensities and flux densities in free space are [6]:
(3.2)
15 = toE
Therefore, the resonant structures discussed here in a medium other than free-space have ef
fective permittivity and permeability which contributes to the electric and magnetic field intensities
20
38. 3.1 Split Ring Resonators and PermeabliJity 21
and flux densities:
(3.3)
The structure is assumed to be on a scale smaller than that of the excitation wavelength and may
be heuristically defined with the homogeneity relation p < ~ where p is the unit cell size.
3.1.1 Array of cylinders
Figure 3.1 An array of metallic cylinders with an external magnetic field applied parallel
to the cylinders.
If an external magnetic field Ho is applied parallel to the cylinders and these cylinders have
a perfect conducting surface, a current j per unit length flows. The field inside the cylinders is
therefore [17]:
2
1rT
H = Ho +j - - j (3.4)
a2
The second term on the right hand side of the above equation is due to the field caused by the
rotating current, and the third term is the result of the depolarizing electric fields with sources at the
top and bottom ends of the cylinders. One must calculate the total electromotive force around the
39. 3.1 Split Ring Resonators and Permeablility 22
circumference of the cylinder is [17]:
2
2
flo -a [ - 7!T J -emf = -7f1' Ho +j - j 27f1'Rj2at a
2
(3.5)
. 2 [ IT 0 7fT oJ 2 R= +~W7f1' flo no +J - a2 J - 7f1'
where R is the resistance of the cylinder surface per unit area. Both terms on the right hand side
above are voltages. The latter term may be considered as loss due to resistance where voltage drop
is current multiplied by resistance. The current j per unit length may be solved for by assuming the
net emf must balance to zero:
iw":1'
2
flo [Ho +j - 7f~2j] -27f1'R= 0
(3.6)
To solve for effective permeability, equation (3.3) is used. Let fl represent the average H field
outside of the cylinders where there is no rotating current:
_ 7f1'2
H= Ho--j (3.7)
a
Substituting in the derived equation for the current j per unit length (3.6) into (3.7) yields:
fl - Ii 7fT
2
-Ho
2
- 0 - ~ [1 _7iT ] + i [ 21'R ]
(l2 WTJ100
(3.8)
1 + i...1R..
= H WTJ100
o 2
1 7iT ] . 2R
[ - (l2 + ~ WT~lO
40. 3.1 Split Ring Resonators and Permeablility 23
The complex effective penneability of a cylinder array is [17]:
B
/-Le!! = --
J.LoH
J.LoHo
I-LoH
Ho (3.9)
3.1.2 Capacitive array of sheets wound on cylinders
Figure 3.2 The cylinders are now seen to have an internal structure. The sheets are wound
in a split ring fashion in such a way that current cannot flow freely. However, if the
distance, d is small enough, current may be induced. An increase in capacitance between
sheets relates to an increase in current. Reference: [17]
The magnetic properties analyzed above change when introducing capacitive elements into the
structure. An array of cylinders is used as before except that each cylinder is now built in a "split
ring" fashion where two inverted rings may be seen when looking from the top down in figure 3.2.
The gap prevents current from flowing around anyone ring. However, Pendry notes that the
capacitance between the 2 rings enables current to flow [17]. A magnetic field parallel to the cylinder
induces currents in the "split rings". The greater the capacitance between the sheets, the greater the
current.
41. 3.1 Split Ring Resonators and Permeab1ility 24
The capacitive array of sheets has an effective permeability if the above process is repeated for
the new model:
2
[2R 3]-1JrT
(3.10)fl-eff = 1 - -a-2 1 +i -W-T-~l-O - -Jr""""2-fl--o-""""2-C-r--=-3
w
C represents the capacitance per unit area between the between the two sheets [17]:
(3.11)
Substituting the capacitance per unit area into the effective permeability model function one
obtains:
7rT2
(i2
fl-eff = 1 - ---"'-----;,,--- (3.12)
1 2Ri 3dc~
+ WTIlO - 7r 2w 2r·l
The numerator above represents the fractional volume of the cell occupied by the interior of
the cylinder. There is a resonant frequency where the effective capacitance balances that of the
inductance. A divergence or vertical asymptote is present in the effective permeability at this fre
quency [17]:
(3.13)
At this resonant frequency, the effective permeability diverges to infinity as the limit of the
denominator in (3.12) approaches zero. This can be seen by substituting (3.13) into (3.12).
Pendry also notes the existence of a magnetic plasma frequency, where thermal movement of
electrons increase and become displaced. This displacement leads to a momentary creation of an
electric field due to a small charge separation. However, the Coulomb force will lead to restoration
of the electron's position (overshoot may occur). This process repeats resulting in oscillations.
(3.14)
42. 3.1 Split Ring Resonators and Permeablility 25
Note the extra term from (3.13). This addition shows that the range over which resonance is
observed up to the plasma frequency is dependent on the fraction of the unit cell structure that is not
internal to any cylinder. In the frequency range the effective permeability is negative. In the region
of negative /-Lef f' if Ero > 0, evanescent waves dominate and radiated EM waves cannot penetrate the
metallic structure. At the plasma frequency, the real part of /-Lef f approaches zero and evanescent
modes no longer dominate.
3.1.3 Split ring resonator
E
Figure 3.3 A thin flat disk shaped split ring resonator.
The above cylindrical designs have the disadvantage of having poor magnetic response when
the magnetic field is not aligned parallel to the cylinders. Furthermore, if the electric field is also
not parallel to the cylinders, the system responds similar an effective metal as current is free to flow
across the length of the cylinders. However, this is fixed with the evolution of the structure into a
disk shaped split ring resonator.
A split ring structure packaged in the form of flat disks can easily be made into arrays. A square
array of flat disks may still be susceptible to magnetic field polarization but the continuous conduc
tion path provided by the cylinders no longer exists. In order to calculate the effective permeability,
the capacitance between the two elements of the split ring must be derived. Pendry makes the
43. 3.1 Split Ring Resonators and Permeablility 26
foUowing assumptions:
• The distance to the inner ring r >> the width of each ring c.
• in (~) >> 1[", where d is the gap size between the two rings.
• Distance between any two rings must be less than r. Hence I < r.
The capacitance between a unit length of these parallel strips is defined in [17J as:
C - EO I ( 2C) _ 1 ( 2C) (3.15)1 - - n - - --In
1[" d 1["~0~ d
Therefore, the third ass,umption implies that the rings must be sufficiently close together. The
magnetic force lines due to currents in the rings are the same as those in a continuous cylinder
described earlier. Hence, the permeabiUty relation somewhat resembles that of the capacitive array
of sheets wound on cylinders.
Substituting (3.15) into (3.10):
7fr2
(l2
~eJJ = 1 - -------'''----------;;-- (3.16)
1 2Ri _ 3dc~
+ wrJ..Lo 7f2w2r 3
A divergence in the effective permeability (3,16) occurs at:
Wo = (3.17)
The variable I above represents the distance between two rings. One can assume this value to
be less than the inner radius of the split ring. This variable may be substituted for by the gap size
between rings d which is also less than the inner radius of the SRR.
The permeability relation for the circular SRR is implemented in Matlab where the dimen
sion variables may be altered to examine the effect of said variables on the permeability resonance
frequency. The Matlab script calculating and plotting the theoretical resonance frequency in the
effective permeabiUty may be found in Appendix A.
44. 27
5
3.2 Circular SRR inclusion simulation in Ansoft HFSS
Real part Ollheo,etlcal permeabll y lrom circular SRR
RaOl.I pari o( ultad d perme billy from S-p3fimetf.r'S
:;
E
a:; I
~IX
0
a. I
f
·1
-2
a f
I,·1
-3
-4
·2
9 10 II 12 13 14 15
a 10
Fre:t (GhZ)
12 14 16 18 2C Freq (13hz)
Figure 3.4 A circular split ring resonator with the variables: a=10mm, c=1 mm, d=O.lmm,
1=2mm and r=2mm is evaluated in Matlab using the effective permeability relation (3.16)
on the left. The equation predicts a resonance in permeability at approximately 13.5GHz.
HFSS simulations to obtain S-paramaters and subsequent paramater extraction predicts a
resonance in the real part of the permeability at 11GHz (right plot). HFSS simulations of
a circular SRR are presented in more detail in section 3.2.
3.2 Circular SRR inclusion simulation in Ansoft HFSS
3.2.1 Unit cell synthesis in HFSS
Ansoft HFSS version 10 is used to synthesize and simulate metamaterial structures in this project.
Previous work in [10] introduced the possibility of reducing simulation time by simulating a single
or small number (much less than the possible hundreds of inclusions embedded in a full structure) of
inclusions embedded in a dielectric medium via the PECIPMC waveguide method. In this method,
two waveports are placed on the entrance and exit faces of the dielectric slab. The "integration line"
feature in HFSS defines the fundamental E field mode of the wave illuminating the entrance. A
PEC symmetry plane acts as a metallic layer. Hence the E field tangential to the surface is zero. The
E field must be normal to the surface or plane. The PMC (defined as Perfect H in HFSS) denote
surfaces or planes where the tangential magnetic field is zero; thus the H-field must be normal to
this surace or plane. Hence, by placing PEC and PMC symmetry planes as such shown in figure
3.5, the E and H vectors are orthogonal to each another. The wave emanating from waveport 1
is thus a plane wave. As a result, it is not necessary to simulate a full metamaterial structure in
45. 283.2 Circular SRR inclusion simulation in Ansoft HFSS
transmission testing. The simulation space may be reduced down to one or a small number of unit
cells. Depending on the size of the inclusions, more than five or six inclusions may lead to longer
simulation and adaptive mesh refinement times. In figure 3.5, Arrows indicate direction of EM wave
propagation. A side view shows the vector direction of the plane wave on the air / metamaterial slab
boundary. PeIfect E (PEC) (XY plane) and Perfect H (PMC) (YZ plane) boundary faces are shown
should the whole slab be simulated in HFSS. Waveports are placed on the entrance and exit faces in
the XZ plane.
Side ,1ew 3D ,ifW of melamalcrial
dielectric slabE
L, slab
H K
Perfen H
bOllndar~·
--i
/
K
)
Dlrectton of
propagation
Perfect H
I
boundal;'
Perfecl E L'ollndal""
..-----. Sial! 11licklless
Figure 3.5 Outline of a complete metamaterial slab.
46. 293.2 Circular SRR inclusion simulation in Ansoft HFSS
PEC plane
Integration
line
PMC plane
Waveport #1
PEC I PMC single unit cell waveguide simulation
Figure 3.6 Single metamaterial cell PECIPMC waveguIde configuration in HFSS. The
waveport integration lines are shown. PECIPMC faces are also indicated.
47. 303.2 Circular SRR inclusion simulation in Ansoft HFSS
3.2.2 Simulation results
To verify the accuracy and utility of Pendry's analytical equations for a circular split ring resonator,
the unit cell in figure 3.6 was simulated. Table 3.1 depicts theoretical and simulated resonant fre
quencies for multiple unit cell dimensions. The use of variables in HFSS simplifies the adjustment
of dimensions such as dielectric thickness, ring radii and gap sizes. For the majority of simulations,
Pendry's criteria for unit cell dimensions are maintained. Results show the Pendry equations provide
only a very rough approximation and that HFSS simulations are absolutely necessary to characterize
a SRR inclusion. The last balded row exhibits the case where pendry's unit cell dimension criteria
are not met. Here the distance between stacked rings is much greater than the inner radius. In this
case, theoretical values are disparate from the simulated results. Note that the second resonance in
the S-parameters is used for fa as they correspond more closely to the theoretical equations pro
posed by Pendry. Simulations are conducted in both a vacuum (fT = 1) and Rogers Duroid 5880
(fT = 2.2) dielectric media. In Figure 3.7, two resonances are shown to exist. However, Pendry's
analysis only predicts the second higher frequency resonance in 8 11 and 821. At these permeability
resonances, the structure acts like an open circuit where 811 increases in magnitude and 821 drops
off significantly.
• The distance to the inner ring r >> the width of each ring c.
• in (5) >> 1r, where d is the gap size between the two rings.
• Distance between any 2 rings must be less than r. Hence dielectric thickness must be less
than r (inner radius).
3.2.3 Parameter variations
To investigate the effect of the split ring resonator size (in terms of overall radius and diameter),
HFSS is used to calculate the S-Parameters for a split ring resonator unit cell. In this par~metric
analysis, the copper trace width, gap size and dielectric height are kept constant. Furthermore, the
boundary unit cell dimensions are fixed. Only the outer radius is varied. In doing so, the overall
48. 313.2 Circular SRR inclusion simulation in Ansoft HFSS
Outer trace gap Inner Diel Thfa Th fa Simul fa Simul fa %diff %diff
radius width size radius thick. vac dur vac dur vac dur
mm mrn mrn mrn mrn Ghz GHz GHz GHz
4.5 1 0.1 2.4 1 7.25 4.9 10 6.5 37.9 32.7
4.1 1 0.1 2 2 13.4 9.08 11.5 7.5 14.2 17.4
3 0.7 0.1 1.5 1 15.6 10.54 13.3 10.3 14.7 2.3
2.5 0.5 0.1 1.4 1 18.5 12.5 17.4 11.9 5.95 4.8
4.1 1 1 1.1 3 84.1 56.7 25.5 16.7 69.7 70.5
Table 3.1 HFSS simulation results for multiple circular SRR unit cell dimensions.
A(1S~ Ccrpotal100 HF5So.t.l'1l'XYPlol1
Q.OCI~-"""Ir'"=~~:::::::::;:::=====-:~;;;;::::::::;;;~
-'00
·1000
-15.00
;:
Resonance 2
predicled b~' Pend')'"
eqnatlons
-3000
-dS(51'lHfl,o~I.WI~aPrc11joJ
~1$.11...'
~ Resonance 1 - <Q~"wolRWt2,~"'If~)l
.35.aa+-~-_ _~-.-_ _- r--_ _- _ _---r-..J,..;;""""';;;c',;,,:~=-;;,;·,::;;"'_ _~..J.j
000 ~ <l "IlO "00'Fr"I1~4
Figure 3.7 S-paramaters obtained from HFSS of a circular SRR with parameters: r =
1.4mrn, trace width = 0.5mm, gap width = O.lmm, lattice spacing (dielectric spacing) =
1mrn and substrate dielectric permittivity = 2.2.
diameter of the SRR changes, hence its overall size. Larger trace lengths exhibit larger inductance
and capacitive coupling between the two rings. Based on the standard resonant frequency equation:
fa = 27rJr:c, increasing both the capacitance and inductance reduces the resonant frequency. Sim
ulation results are shown in Figure 3.8. In the simulation investigating radius lengths, trace width is
kept constant at 0.5mm. Gap sizing is O.lmm. Unit cell boundaries unchanged at 5mrn x 5mm with
a dielectric height of 1mrn. The Dielectric is Rogers Duroid 8500 Er =2.2
49. 323.2 Circular SRR inclusion simulation in Ansoft HFSS
Figure 3.8 Resonant Frequency of circular SRR for multiple outer radius lengths.
Another parameter of interest is the substrate permittivity ET • Results depicted in Figure 3.9
show that resonant frequency of an SRR decreases as ET increases. This is important as the choice of
substrate pennittivity needs to be finalized before performing final design simulations. Furthermore
to compensate for higher permittivities, other parameters such as SRR outer radius, trace widths or
gap widths need alteration.
Additional variable parameters include copper trace widths and gap widths. Copper trace width
is represented by the variable'c' in equation (3.17); the argument of a natural log function. Increas
ing ,c', decreases the resonant frequency. The pattern is exponential in nature due to the natural log
function. The same analysis may be applied to the gap widths. Increasing the gap width reduces the
inner ring radius (r) and hence also increases the value of the natural log function. As a result, the
resonant frequency increases exponentially.
50. 333.2 Circular SRR inclusion simulation in Ansoft HFSS
Resonance frequency of Circular SRR as a function of Dielectric permittivity
18
16
N
I 14
Q.
>- 12u
c:
GO
::J 100
~
LL
8G>
U
c:
10 6c:
0
VI
GO 4
0::
2
0
0 0.5 1.5 2 25 3 35 4 45 5 5.5
Dielectric Constant permittivity
Figure 3.9 Resonant Frequency of circular SRR for varying substrate dielectric constants.
SRR outer radius kept constant at 2.5mm. Trace width is 0.5mm. Gap sizing is O.lmm.
Unit cell boundaries unchanged at 5mm x 5mm with a dielectric height of Imm.
Resonant frequency of circular SRR as a function of copper trace/ring widths
22.5
20
N
::t 17.5
~
>0
l:
15
'"~
l:T
'"u: 12.5
1:
l:'"0
'" 10
a::'"
7.5
5
0 0.2 0.4 0.6 0.8 1.2 1.4 1.6 1.8 2
TracelRing width lmm)
Figure 3.10 Resonant Frequency of circular SRR for varying copper trace widths. SRR
outer radius kept constant at 4.0mm. Gap sizing is O.lmm. Unit cell boundaries un
changed at 5mm x 5mm with a dielectric height of Imm. The Dielectric is Rogers Duroid
8500 Er =2.2
51. 3.3 Square / Quadrilateral SRR inclusion simulation in Ansoft HFSS 34
Resonant frequency of circular SRR as a function of gap width
20
19
18
N 17
J:
~ 16
>0
cQ) 15
:l
coQ) 14
It
....c 13
III
c
0 12
III
cu
0::: 11
10
9
8
0 0.2 04 0.6 0.8 1 1.2 14 1.6 1.8
Gap width (mm)
Figure 3.11 Resonant Frequency of circular SRR for varying gap widths. SRR outer
radius kept constant at 4.0mm. Trace width is 0.5mm. Unit cell boundaries unchanged
at 5mm x 5mm with a dielectric height of Imm. The Dielectric is Rogers Duroid 8500
Er-=2.2
3.3 Square / Quadrilateral SRR inclusion simulation in Ansoft HFSS
3.3.1 Unit cell synthesis in HFSS
Unit synthesis is almost identical to that of the circular SRR. However, instead of using cylinders
with formed gaps using boolean operations in HFSS, the box drawing tool is especially useful for
creating the structure. Boolean operations may be used to form gaps between and inside rings.
A PECIPMC waveguide setup for a single unit cell is again used. The Perfect E and Perfect H
symmetry planes are unchanged.
3.3.2 Parameter variations
For the parameter variations of the Quadrilateral SRR unit cell shown in the graphs below, the first
two major resonances are shown. Both resonances show a peak in the reflection of the unit cell and
52. 353.3 Square / Quadrilateral SRR inclusion simulation in Ansoft HFSS
z yPerfect E (XY plane)
~x
E
H
Vaveport
1
Perfect H
Figure 3.12 Single unit cell of a square SRR in the PECIPMC waveguide configuration
for simulation in HFSS.
a minimum in transmission. Hence the unit cell is acting like an open circuit at these two resonance
frequencies. This is characteristic of a unit cell with negative permeability only as reported by
Ziolkowski in [10]. Figure 3.13 shows the change in resonance frequency as outer radius length is
varied. Trace widths are kept constant at 0.5mm. Gap sizing is O.lmm. Unit cell boundaries are
unchanged at 5mm x 5mm with a dielectric height of Imm. The Dielectric is Rogers Duroid 8500
t1·=2.2. Furthermore, Figure 3.14 shows a similar response in the resonance frequency to changes
in the inclusions's copper trace width. SRR outer radius is kept constant at 4.0mm. Gap sizing
is O.lmm. Unit cell boundaries unchanged at 5mm x 5mm with a dielectric height of Imm. The
Dielectric is Rogers Duroid 8500 tr=2.2
Figure 3.15 depicts the effect of split ring gap widths on the measured S-parameter resonance
frequency. The gaps of the outer and inner rings are identical to simplify analysis and remove the
addition of extra variables. SRR outer radius is kept constant at 4.0mm. Trace width is 0.5mm. Unit
cell boundaries are unchanged at 5mm x 5mm with a dielectric height of Imm. The Dielectric is
Rogers Duroid 8500 tr=2.2.
53. 363.3 Square / Quadrilateral SRR inclusion simulation in Ansoft HFSS
Resonance Frequency as a function of split ring
outer diameter for a square/quadrilateral SRR
375 -,-----------------------.
35
II
32.5
N 30 --+-- resonance 1
§. 27.5 - ... - resonance 2
>- 25o •.
~ 225
.,5- 20
'..it 17.5
~ 15 " 'a
t: ............-.~ 125 - .....o
~ 10
Q: 7.5
5
2.5
O+----r-----,--,-----,--,---------r----,-------,-----,---.--------r------l
60 70 80 90 100 110 120 130 140 150 160 170 180
Outer diameter/length (mils)
Figure 3.13 Resonant Frequency of a square SRR with multiple outer radius lengths.
Resonance frequency of the Quadrilateral SRR as
a function of copper trace widths
20 -,----------------------,
19
18 ~
17 ]I
16
¥ 15
~ 14 .----~ 13 .-W'
12 ...~ .. _... __ resonance 1
g. 11
• ...... - .. - resonance 2., 10
Li:., 9 ........
g 8
~ 7
~ 6
., 5
D:: 4
3
2
1
O+-----.------,,--------,--------,--,----,---,-,-------,---,--.-------,----r-,-------!
o 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30
Copper trace/Ring width (mils)
Figure 3.14 Resonant Frequency of square SRR for varying copper trace widths.
Results follow the same correlations and relations between the resonance frequencies and square
SRR parameters as seen in the earlier HFSS simulation results of circular SRRs. For the final meta
54. 373.3 Square / Quadrilateral SRR inclusion simulation in Ansoft HFSS
Resonance frequency as a function of gap
sizes in a square/quadrilateral SRR
16 -,---------------------------,
15 "..
14
........ "'"N 13
..- ........I 12
~ 11 ....~..-.---->- ___ resonance 1
~ 10
- ... resonance 2
~ 9
c-
O> 8
u:0> 7
~ 6l'll
S 5
::: 4
~ 3
2
1
0+---,--------,------,-----,---------,-----,------,--,---------1
o 5 10 15 20 25 30 35 40 45
Gap width (mils)
Figure 3.15 Resonant Frequency of square SRR for varying gap widths.
material designs discussed in a Chapter 9, parameters may be adjusted to meet resonance frequency
requirements. The parametric analysis results here provide an intuitive way to adjust the parameters
to meet resonance goals.
55. Chapter 4
Wire and strip structures to realize
negative permittivity
While the split ring resonator reacts to the presence of a magnetic field thereby affecting the perme
ability of the bulk material, it is also necessary to present inclusions that produce dielectric responses
based on the illuminating E-field. Such structures may be designed to exhibit negative permittivity
(Er ) over a specified frequency range.
Metals exhibit a plasma resonance of their electrons when when illuminated by electromag
netic radiation of a certain frequency. In the ideal case, the relative permittivity of a metal may be
described by the relation [18J:
(4.1)
The plasma frequency wp , is given in terms of the electron density, n, the electron mass, me,
and charge, e. For frequencies less than the plasma frequency, metal exhibits negative permittivity.
In regions of exclusive negative permittivity evanescent modes dominate. In this region radiation
does not penetrate the metal. Furthermore, the ideal equation above is not valid in the presence
of losses, "(. Equations (4.1) and (4.2) are state that metals exhibit negative permittivitty below the
plasma resonance frequency. Hence, a negative permittivity inclusion designed to exhibit a dielectric
38
56. 4.1 Thin wire structures 39
response to an, incident E field must be illuminated by ractiation below the plasma frequency.
2w
Emetal = 1 - ( :. )
w w Zf (4.2)
4.1 Thin wire structures
If a periodic structure of thin wires is to be considered, it is important to consider the case of an
illuminating E-field parallel to the wire lines. In the previous chapter, cylinders were considered as
inclusions to achieve a magnetic response from the presence of a H-field. In this case, thin wires are
considered. According [18], in thin wires, the average electron density is reduced because only part
of the unit cell or collection of wires in a dielectric medium is occupied by a metal. Thus the overall
average density of electrons, nej j, in wires of radius r with a density n in the wires themselves and
wire seperation a may be represented as:
(4.3)
Furthermore, the effective electron mass is enhanced due to magnetic effects. The flow of
current, I produces a magnetic field around the wire:
2
H(R) = _1_ = n:r nve
2n:R 2n:R
H(R) = I-Loh
:;; x A
(4.4)
where
2
A(R) = muon:r nve in (~)
2n: R
In (4.4), R represents field distance from the wire, v is the mean electron velocity and a is
the lattice constant (separation between wires) (see Figure 12.5). The momentum contribution to
57. 4.1 Thin wire structures 40
electrons in a magnetic field is eA. Per unit length the momentum of the wire is:
2
f.10e2 (1rT n) 2 V ( a)eA(T)1rT
2
nA(r) = In
21r r (4.5)
2
= m cff1rT nv
The effective mass of the electrons is mcff. One can re-arrange (4.5) to obtain mcff:
(4.6)
The plasma frequency of the thin wire structure defines the upper limit for the domain in which
the bulk permittivity is negative. From (4.1):
21r
(4.7)
a2ln (Q:) 1 II
r J-LOC61-"0
21rC6
a2ln (7.)
The above relation is used to determine the plasma frequency of the rod structures. The follow
ing section tabulates results obtained from HFSS when simulating an array of thin wire rods.
Simulation of rod structures in HFSS
A unit cell is constructed in the PECIPMC waveguide format as previously discussed. Several
cylinders composed of copper are used to create the wire rod array. The cylinders are seperated
by the distance a, with radius, T. The rods must contact the top and bottom faces of the unit
cell. As the top and bottom faces of the cell are Perfect E planes appr,oximating metal sheets,
the structure may be considered a parallel plate waveguide [19]. In practice, to ensure there is a
58. 4.1 Thin wire structures 41
sufficient dielectric response to the electric field, the rods must connect to the metal sheets of the
parallel plate waveguide. In the case of simulations they must touch the top and bottom face of the
PECIPMC waveguide but must not completely intersect it otherwise HFSS will produce errors.
Figure 4.1 HFSS structure example for an array of thin wire rods.
The plasma frequency is visible in in transmission data when a peak in transmission (821) is
seen. An example of transmission data calculated by full-wave simulation in HFSS is given in
figure 4.2.
Several simulations with different cylinder radii and lattice spacing are considered in table 4.1.
The theoretical results in an air dielectric are compared to the HFSS solutions. Note the large
percentage difference between simulated and theoretical results. The radius of the cylinders used
are not "thin" by J B Pendry's standards. Thicker wires undergo higher resistive losses at microwave
frequencies which tends to increase the plasma frequency.
Table 4.1 shows an unusually high percentage difference between theoretical and simulated data.
This is due to the diameter of the cylindrical wires. Even at O.lmm, they cannot be considered thin
enough to be treated as ideal in equation (4.1). The table shows percentage difference in theoretical
to simulated results decreases with radius. However, simulation of radii less than O.1mm becomes
difficult in HFSS as the solver finds it impossible to fit tetrahedra to extremely small structures.
59. 4.1 Thin wire structures 42
r(mm) a (mm) theorerical fp (GHz) simul fp (GHz) %difference
0.1 5 12.1 17.7 31.63
0.2 5 13.3 20 33.3
0.5 5 15.8 24.3 35.08
1.5 5 21.8 47.2 53.8
0.1 2.5 26.7 39.6 32.6
0.1 10 5.58 8.7 35.8
Table 4.1 Theoretical and simulated plasma frequencies for thin 3x3 wire rod structure
unit cells of various wire radii and lattice spacings in an air medium.
Anso~ CorporafJon HfSSOo"!Jl'XY Plot 1
o00 ""1""----------------;;;;;;:::-----:7-'.......;;::---------::::;;ot
Q1rverto
-500 - a6t . veflortl.W....ef)f1.1))
~1:SWe"t'P1
- (ft:S(Wa...eFat2."'II"~))
5«up1:~~1
-1000
-1500
-2500
IS111
-30.00
-35.00
IS211
-4000-+--~-_-_-~-___,---~-~-_---,----------____1
1000 1500 :2000 2500
FreQ (Ci"i21
Figure 4.2 Transmission results from a 3x3 wire rod array simulated in HFSS. Cylinder
radius =O.2mm. Lattice spacing, a =5mm, and the dielectric medium is air. Resonance
is seen at 20GHz. The location of the plasma frequency is thus at wp =20GHz.
Reducing the wire width has the effect of reducing the plasma frequency. For left handed media,
this is not desired as one must be sure the entire frequency range of double negative operation
desired is below the wire inclusions plasma frequency to ensure permittivity remains negative. If
a low plasma frequency is desired, then one may embed the rods in a high permittivity dielectric
medium in comparison to air (Er :::::: 1). This method may be necessary when trying to design zero-
index metamaterial structures at X-band or lower frequency bands. The dielectric substrate may be
used to lower the resonant plasma frequency without altering the inclusion structure.
60. 434.2 Capacitively loaded strips (CLS)
4.2 Capacitively loaded strips (CLS)
The capacitively loaded strip is an alternative inclusion that reacts to an incident E-field parallel
to the plane of the inclusion. This structure uses capacitively loaded wires on each end as a re
placement for the configuration of a thin wire or rod, which must be connected directly to a parallel
plate to induce a dielectric response to the E-field. However, for a capacitively loaded strip, such
a connection is not necessary due to the diploles loaded on the strip. Hence, the capacitive dipole
strips act as parallel plates and thus the metarnaterial does not require a parallel plate waveguide
configuration. However, it should be noted that the capacitively loaded strip does not exhibit nega
tive permittivity over the entire frequency range below the plasma frequency. There is a resonance
in the permittivity that occurs below the plasma frequency. This is reflected in the transmission and
reflection data obtained from HFSS by looking for resonance peaks in 521. Two resonances are vis
ible separated by a stop band where evanescent modes dominate. The first resonance corresponds
to the permittivity (E) becoming negative and the plasma resonance indicates the frequency range
where the permittivity approaches zero. It is important that the chosen frequency for left-handed
operation falls within the range of left-handed operation; where the permittivity is negative. For
epsilon near zero (ENZ) metarnaterials, design optimization should target the plasma frequency to
be in the range of the required operation frequency.
61. 444.2 Capacitively loaded strips (CLS)
WavepoJ12
Perreet
H
Perfect H
plane
PEe
W.vepoJ11
Figure 4.3 Unit cell consisting of 2x2 array of capacitive loaded strips in PECIPMC
waveguide configuration.
Ansa' COCJX){3.lion XYPlot 1 HFSSDesigll
000T~;C:=5<~r-------~;:------------~7~~~"'i
i·1000
ISHI
-2000
-3000
;: -.40 00
Resonance in
i
IS211
penultttvUy
·5000
·60.00
JPlasma frequeocy
WNe-WCI
·7000 - .Ifil!,(Vlo'&Vl:~I.W....ePtrtl))
5:.!tti.ol SwIl!~l
-cII(S(Yi'&... IIP:ln2,"No.~lllJ
200010 CO500
$!Iuf.ll ~'"I:II
-aooo+=:;:::::::;:=:::;==;:=::;=:;:::::~~~--,~~~-_.---_~~~--,
o 3000l5 00
.----~~~_~
Figure 4.4 Simulated S-parameter data on a 2x2 array of CLS structures. The low reso
nance is at 4AGhz and the plasma frequency where evanescent modes no longer dominate
is 25.7GHz. CLS height (h) =9.6mm and capacitive strip width (w) =4.5mm. Microstrip
width =OAmm. Lattice spacing (a) =2.5mm.
62. 454.2 Capacitively loaded strips (CLS)
The length of the capacitive loaded ends of the strips (w) influences the frequency at which
the permittivity of the structure goes negative. Longer strips reduce this resonance frequency as
capacitive coupling between any 2 CLS structures in the H-plane will increase [31]. For testing in
the X-band frequency range, the widths must be large enough such that the first resonance occurs
at a frequency lower than 7 GHz. In addition, this width is dependent on the dielectric substrate
and the microstrip width. Table 4.2 shows simulated values for permittivity resonance and plasma
frequency from transmission data on a 2x2 copper array of capacitively loaded strips embedded
in an air PECIPMC waveguide. The heights and lattice spacings are kept constant. Note that the
plasma frequency also decreases with an increase in CLS width. However the percentage change
is only 4% in comparison to the decrease in the resonant frequency of 42%. Thus the resonant
frequency where permittivity changes from positive to negative is solely affected by the increase in
capacitor end width.
capacitor end width (w) resonant frequency (fo) plasma frequency
mm GHz GHz
0.4 7.7 26.9
2 6.1 26.5
2.5 5.6 26.3
3 5.2 26.3
4 4.5 26.1
4.5 4.4 25.7
Table 4.2 Simulated resonant and plasma frequencies for a 2x2 array of CLS structures
in air with lattice spacing, a = 2.5mm, height=9.6mm and microstrip width=0.4mm. The
capacitive load widths on each end are varied.
63. Chapter 5
The S-shaped Split Ring Resonator
Inclusion (S-SRR)
An S-shaped split ring resonator has been proposed in [30]. A theoretical study of its penneabi
ilty and pennittivity characteristics is provided in [31]. These studies are summarized here and are
later used as an initial benchmark to create a periodic metamaterial slab for transmission testing.
To estimate pennittivity and penneability characteristics of an S-shaped resonator design prior to
simulation in Ansoft HFSS, a Matlab script implementing the analytical relations developed here is
implemented and can be found in the Appendix.
Circular or quadrilateral split ring resonators require the use of a rod, thin wire or capactively loaded
strip structure in order to respond to the electric field and create left-handed properties at the fre
quency of interest. While, a circular or quadrilateral split ring resonator may respond to the electric
field, the vertical asymptote (divergence) frequency for the permittivity relation is higher than that
of the permeability by factors of two or three, hence the region of interest is not a true left handed
metamaterial without the secondary structures [31]. The alternative resonator design proposed by
Chen et al does not require secondary structures such as rods, CLSs, or thin wires.
The basic S-SRR structure along with a a periodic array of such structures is shown below. The
copper/metallic strips form a'S' shape. Capacitive coupling is achieved through the addition of a
46
64. 47
reversed S-shaped strip printed back to back with a separation d.
Unit cell
z
~v
b
x
F3
a
be ght
c.
Figure 5.1 2D and 3D diagrams of S-shaped SRR structure.
The area of a periodic unit cell A, is given by A = xy. The numeric '8' shaped pattern fonned
by the back to back split rings is shown in Figure 5.1. wee areas can be distinguished from the
two dimensional image. Area I forms loop 1 at the top of the '8' pattern, while area II represents
loop 2 and the bottom of the loop pattern. Area III represents the area not enclosed by these rings.
Additionally, Fl, F2 and F3 represent the fractional volume of the unit cell occupied by these loops.
The summation of these fractional volumes is normalized to 1:
FI + F2 + F3 = I (5.1)
A linearly polarized plane wave incident on the period S-SRR structures parallel to the YZ plane
causes a time varying external magnetic field to be applied normal to the S-SRR plane (XZ plane).
Currents flow in the split ring and are shown in the 2 dimensional diagram above. Using current
65. 48
densities (Amperes per unit length) and loop equations, the following relations must be satisfied:
. hJl =
l
. h
J2 =
l
(5.2)
Magnetic fields commonly show a spreading of the magnetic field lines. This phenomenon
known as the fringing effect can be negated under the assumption that the S-SRRs along the plane
they lie are sufficiently close together (a fraction of the unit cell size) Common values at X-band
frequencies range from 0.1 mm to 2mm. Simulations and practical implementations shown in section
5.1 later will attempt spacing at 62 mils; a mere 1.5748 mm. Re-arranging the above relations, it is
found that H2 = HI -)1 +)2 and H3 = HI - )1· Hence, H2 and H3 may be substituted into (5.2)
in terms of HI:
This analysis is repeated for H2 and H3 resulting in three equations for the time varying mag
netic fields in each region of interest:
(5.3)
As there is no voltage potential related with the S-SRR structures, the net electromotive force
around both loops sums to zero. It should be noted that the fractional total area used to determine
66. 49
potential is FIS for loop 1, where S has previously been described as the total area of the periodic
unit cell [31].
a
emil = - at (J-toHIFIS)
(5.4)
= RsII + ~s Jh dt + dJ(II + 12) dt
rn
a
emh = - at (/lOH2 F2S)
(5.5)
= Rs12 + ~s Jhdt + dJ(h + 12 ) dt
rn
Rs represents the resistances of the metallic strips. Capacitances Cs and Crn are due to the
toplbottom metallic strips and the mutual capacitance of the center metallic strips respectively. The
right-hand integral of (5.4) and (5.5) has a sum of currents I1 +12 due to the loop arrangement. The
capacitance between the two metallic strips is calculated assuming the distance between the S-SRR
layer and the inverted layer remains constant throughout. Thus Cs and Crn are equal:
(5.6)
To determine the frequency dependence of permeability in the S-SRR structure, (5.4) and (5.5)
must be represented in the frequency domain. The summation of operations in the time domain
remains as such in the frequency domain. The partial derivative operation %t may be represented by
-iw and the integral Jdt by - L in the frequency domain.
(5.7)
(5.8)
67. 50
From Pendry's analysis of the circular SRR structure in [17], the permeability can be defined in
terms of the time varying magnetic field and the permeability of free space:
(5.9)
The current densities )1 and)2 are unknown and must be substituted out. This is done through
the re-arrangement and substitution of (5.7) into (5.8). The result of the lengthy calculation is shown
by Chen et 81 to produce a complex relation for the effective permeability:
The following abbreviations are used:
A (R) = WJ10S (F't + Fi) + Rsl
B (R) = (Rs l)2 (5.11)
C (R) = [WJ1OS (Fl + F2) - ~ (~s dm)] Rsl
The divergence or vertical asymptotes in the effective permeability relation where the perme
ability becomes negative can be found by finding the frequency, w, where the denominator equals
zero. Due to the quadratic dependency in the denominator, there are 2 solutions. Hence, in general,
if the loop areas F1 and F2 are not equal, then equation (5.10) has two resonant frequencies:
(5.12)
(5.13)
68. 5.1 S-shaped SRR inclusion simulations 51
When H = F2 = F, there is only one resonant frequency related to the effective permeability.
The permeabiliy relation and the resonant frequency solution may be represented as:
2F+iD
/-Lej j = 1 - ---1--(--'--/--2-/-:-)----.
1 - w2J.LoFS Cs + Cm
- E + ~G
where
2 ( 1
X = (W/-LO FS) 1- wf-LOFSC
l)s (5.14)
A
D=
X
E= B
X
G=C
X
1 (l 2l ) (5.15)
WmO = f-LOFS C + Cs m
Prior to simulation it is important to first choose the desired resonance frequency(s) and obtain
the inclusion dimensions that realize the theoretical desired resonance frequency goals.
5.1 S-shaped SRR inclusion simulations
5.1.1 Unit cell Synthesis
Like the split ring resonator structures synthesized in HFSS, the S-SRR structures may also be
modeled with a PECIPMC waveguide model. One s-shaped copper structure may be embedded in
a dielectric medium. To generate the mirrored S shape, the mirror and move commands are used.
Again modal S-parameters are generated using 2 waveports with one dominant mode as described
by the integration line.
5.1.2 Simulation results
As in simulations for the basic SRR structures presented in the previous chapter, simulations in
HFSS are performed to verify analytical equations such as (5.12-5.13, 5.15). The table below depicts
69. 5.1 S-shaped SRR inclusion simulations 52
h xy
Wa·e
J
E
B
Figure 5.2 A synthesized S-SRR unit cell in HFSS. Copper thickness is 1 oz (0.2mm).
F1 = F2 in this case.
the theoretical and simulated resonant frequencies for varying unit cells. Note that the analytic
equations described above may provide methods to obtain 2 resonant frequencies due to the differing
current loop dimensions in the S-shaped SRR inclusions. However, Table 5.1 presents results for
unit cell designs with a single established resonant frequency. The two loops formed by the mirrored
S-shapes are thus identical and F1 = F2.
w h a b c d I theoretical Actual %diff
(mm) (nun) (mm) (nun) (mm) (mm) (nun) fo (GHz) fo (GHz)
4 5 8 6.5 0.5 1.57 2.36 20.6 18.8 8.737
3 7 9 7 0.5 0.9 2 17.7 14.5 18.079
4.2 7.4 9 7.5 0.6 1.2 2 12.9 11 14.728
3.9 5.8 8.5 7.5 0.75 0.5 1.8 11.6 10.3 11.21
5 10 8 11 1 0.75 1.5 5.5 6.8 23.64
Table 5.1 HFSS simulation results for varying unit cell dimensions. Results show the
S-SRR equations provide only a very rough approximation and that HFSS simulations are
absolutely necessary to characterize a SRR inclusion.
5.1.3 Parameter Variations
Unlike the Split ring resonators presented in the previous chapter, the S-shaped resonators are not
uniform in radius. Hence, the height and the width of the structures will be treated individually here
70. 5.1 S-shaped SRR inclusion simulations 53
and may be separately optimized to reach resonance frequency goals. It is expected that increasing
the inductance increases the overall inductance of the structure. An increase to bulk capacitance
or inductance inherently reduces the resonant frequency. The same may be said of an increase in
S-SRR width. The effect of S-SRR height is confirmed in Figure 5.3. In this simulation, SRR
width = 4mm, copper width = 0.5mm, spacing between mirrored S-shaped resonators (d) = 1.5mm,
distsance between S-shape pairs, I = 2.5mm. Unit cell height (a) = 10mm and width (b) = 7mm.
Similarly, the effect of width on the S-shaped split ring resonator may be seen in Figure 5.4. In this
case, SRR height =6mm, copper width =0.5mm, spacing between mirrored S-shaped resonators
(d) = 1.5mm, distsance between S-shape pairs, I = 2.5mm. Unit cell height (a) = lOmm and width
(b) = 7mm.
Resonant frequency versus S-SRR height
18 . . , - - - - - - - - - - - - - - - - - - - - ,
17
N-J: 16
Q.
r;- 15
c:.,
::::I
g 14
...LL.
C 13
c:'"o
:: 12
~
11
10 +---.---,.--.--.----,.--.--.-----.--.--.----.-.--r--l
3 35 4 45 5 55 6 6.5 7 75 8 8.5 9 95 10
S-SRR height (mm)
Figure 5.3 Resonant Frequency of S-SRR for varying inclusion heights.
Dielectric permittivity affects the measured resonance frequency. The simulation results show
that embedding the copper inclusions in Roger's Duroid 5880 (cr' = 2.2) produces a resonance
frequency higher than that of an inclusion embedded in FR-4 substrate (Cr = 4.4). The relation may
be approximated with a linear fit for relative permittivities > 2.
To validate the relations for uneven current loops in the S-SRR structure where F1 i= F2 (5.12)
71. 5.1 S-shaped SRR inclusion simulations 54
Resonant frequency as a function of S-5RR width
30 .,--~------------r======>
- S-SRR width
25
N
:I:
~
>
~ 20
..:l
0
f
u.
e 15
"'c:
o
..co
a:
10
1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 75 8
S-SRR width (mm)
Figure 5.4 Resonant Frequency of S-SRR for varying inclusion widths.
Resonance frequency as a function of substrate
C1electric permittivity for the S~haped SRR inclusion
16 - . - - - - - - - - - - - - - - - - - - - - - - - - ,
-resonant frequency
15
14
I
~
13
~
>
~ 12
..::J
cr
f 11
u.
..~ 10
..c:
o
: 9
a:
8
7
15 2 2.5 3 3.5 4 4.5 5
Dielectric permittivity
Figure 5.5 Resonant Frequency of S-SRR for varying dielectric pernuttlVltles. SRR
height =6mm, SRR width =4mm, copper width =O.5mm, spacing between mirrored
S-shaped resonators (d) =1.5mm, distsance between S-shape pairs, I =2.5mm. Unit cell
height (a) =lOmm and width (b) =7mm.
72. 5.1 S-shaped SRR inclusion simulations 55
and (5.13), the ratios of the areas covered by the 2 loops; Fl, Fz are varied. To accomplish this
in HFSS, variables are used to alter the location of the center bar of each S-shape by specifying a
ratio between 0 and 1. A value of 0 specifies the geometry in which the center bar overlaps the top
bar of the'S' shape. A value of 0.5 means it remains in the center and F1 = Fz. A ratio of 1 thus
means the center bar now overlaps the bottom bar of the'S' shape. Table 5.2 presents the results of
variable center bar location and thus the proportion of the unit cell enclosed by each loop: Fl and
Fz·
Fl Fz theoretical f01 theoretical foz simul f01 simul foz
0.3 0.3 7.54 N/A 7.3 N/A
0.36 0.24 4.31 7.7 4.3 7.5
0.42 0.18 4.2 8.5 4.1 7.9
0.48 0.12 4.06 10.1 4.15 8.7
0.51 0.09 3.99 11.5 3.88 9.3
Table 5.2 HFSS simulation results for varying loop ratios to alter the two resonance fre
quencies.
F1 =F2 =0.3 F1 = 0.45, F2 = 0.15
R... pat oflll""et~a1 ponnalIIlIy;OO1 S-SRR x10' R.iI part 01 the<i<eIIalporm.;,bj,ly from S-SRR
500 r--.....---.--..,....---.---.-..---.....---.-.......-., 15
lQO
I
100
i ofo--------""""""l,..- ~ 0 '-
0:
'"·100
~.I
·200
·laO
1
-II.1000.--'--~~1c-- ....~S-'!&c--~7~-'!!--..JIO' o & 10 12
Freq (Ohz) FraqlGhz)
Figure 5.6 Divergence/resonance simulation in matlab for an S-SRR unit cell with
height=7.5mm, width=4mm, copper width = O.5mm, distance between mirrored
rings=0.5mm, S-SRR pair seperation, l=lmm, unit cell: 1Ommx5mm.
73. 565.2 Summary of metallic inclusions
5.2 Summary of metallic inclusions
SRR Thin rods/ CLS SRRlCLS S-SRR
combined
structure
Transmission 5 21 > 0 521- > 1 at 5 21 > 1 5 21 > 1
at resonance plasma resonance
Effect on NONE Negative below the Negative at the Negative at the
permittivity plasma resonance resonance
frequency. frequency. frequency.
Effect on Negative at the NONE Negative at the Negative at the
permeability resonance resonance resonance
frequency. frequency. frequency.
Table 5.3 Summary of the transmission, permittivity and permeability characteristics of
the inclusions introduced in this thesis.
Table 5.3 indicates the common dielecric and magnetic properties seen in split ring resonator,
wire strip, combined SRRlCLS and s-shaped structures. This table may be used as a summary when
designing around an application. For filtering, an SRR only metamaterial would provide stop-band
characteristics at the targetted resonance frequency while the combined SRRlCLS or S-shaped SRR
(S-SRR) structures show pass-band/matching to free-space.
74. Chapter 6
Parameter Extraction applied to
Discrete Metallic inclusions
6.1 Extraction results from HFSS simulations
The theory for extracting homogeneous material parameters such as tr" J-Lr and n is presented in
Chapter 2. A Matlab script available in the Appendix reads in column vectors of data from an Excel
file. This data includes frequency points measured in HFSS along with the associative scattering
parameters at those frequencies. Given magnitude and phase (degrees) data for 8 11 and 8 21 , their
complex values may be obtained.
6.1.1 Circular SRR with thin wire strips
A unit cell composed of a circular SRR and a thin wire strip to achieve simultaneous negative
permeability and permittivity. A picture of the unit cell is shown below. The transmission and
reflection s-parameters are also shown as a function of frequency.
57
75. 6.1 Extraction results from HFSS simulations S8
z
Figure 6.1 A unit cell with a circular SRR and thin wire strip. The boundaries are lOmm x
lOmm in the X and Y directions. The separation between the SRR and wire strip is Imm.
SRR outer radius is 3mm with a copper strip width of Imm and gap width of O.2mm.
Ansoft Corporation HFSSDesi'1'1XY Plot 1
O.OOJ========:=::======-------=:::::::::=--"""':::::::=---==::::::=---~OC;:::;:;:;::::=_l
-1000
- cfl(S(I,I1V1e'R::rt1 ",'I.'JePt.tll)
setup! Sw~1
- cS($iWa1JePtft2 Wa...eR:lrtl»)
-20.00 Setupl : Swoep1
-30.00
-40.00
-50.00-t-~_~_ _,__~~~--,~--~__,_~_-~~~~~---.--~_~__,__--~.___,~~--_1
1200 13.00 1<.00 1500 17 00 18.00 1900
Figure 6.2 Resonance shown in scattering parameters at approximately 18Ghz_
20.00
76. 6.1 Extraction results from HFSS simulations 59
Extracted permittivities for a single circular SRR
and wire strip unit cell
30
-Re(eps)1
25 -Re(eps2)
-Re(eps)320
15
iiiI/)
10
GJ
..·c 5
2
>- 0 ,---------
:E
> 1 13 14 15E -5
·e
Q;
-10c..
-15
-20
-25
-30
Frequency (GHz)
Figure 6.3 Extracted real part of (Er from S-parameters. The equations are used respec
tively.
Extracted permeability for unit cell with circular SRR
and thin wire strip
30
25 I-Re(mu)1
20
iii 15
I/)
<D
E
10
c:
2 5
~ 0
:0
III -5 13 14 15 16 17
Gl
E -10Q)
c.. -15
-20
-25
-30
Frequency (GHz)
Figure 6.4 Extracted real part of J.Lr. from S-parameters.