Single-Phase Grid-tied Transformerless Inverter of Zero Leakage Current for PV System
•
0 likes•15 views
Multi-level transformerless inverters are widely used in grid-tied PV systems since they characterized by higher efficiency and lower cost. In this context, new topologies, modulation, and control schemes were presented to solve problems of a common-mode voltage and leakage current. This work proposes a transformerless five-level inverter with zero leakage current and ability to reduce the harmonic output content for a grid-tied single-phase PV system. The neutral of the grid links to a common on which the negative and the positive terminals of the DC-link are connected via parasitic capacitors that can eliminate the leakage current. The proposed topology, with its inherent circuit structure, leads to boost the overall efficiency. Simulation and experimental results show almost zero leakage current and a high-quality output when maintaining balanced capacitor voltages on the DC-link input. The experimental results show 1.07% THD and 96.3 % maximum efficiency when injecting a power of 1.1 kW that verify the performance of the proposed inverter with PV sources.
Report
Share
Report
Share
Download to read offline
![ELECTRICAL PROJECTS USING MATLAB/SIMULINK
Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in
0-9347143789/9949240245
For Simulation Results of the project Contact Us
Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in
0-9347143789/9949240245
CONCLUSION:
A new high-performance transformerless 5L-NPC inverter with its control strategy for a grid-tied
PV system has been presented. The major advantages of the presented system can be brief as
follows: 1. The topology of employing diode clamping MLI with suitable stray capacitors makes
the leakage current to flow through the system in a very low value reaches zero. Furthermore, the
system offers a connection between the DC-link pass bar of a solar PV array with the grid neutral
terminal that results in zero leakage current. 2. The operation of the employed five-level
topology results in high performance for the harmonic distortion that allows the reduction of
filter components as compared with lower MLIs. 3. The proposed 5L-NPC topology eliminated
the CM leakage current with 1.07% THD by using eight power switches. The results confirmed
the above-stated advantages, and the proposed system offers approximately similar
characteristics in reactive and real power injections. Therefore, the proposed inverter topology
and its modulation scheme were a suitable and attractive solution for single-phase grid-tied PV
systems. Although the proposed 5L-NPC system achieved zero CM leakage current with a very-
low THD, the design is limited by eight switches that are recommended to be reduced in future
work. Moreover, the presented system solved the balancing issue of the DC-link capacitors’
voltages that required for proper operation by a modulation strategy inspired in [21], we
recommend easier algorithms to solve such issue.
REFERENCES:
[1] S. Padmanaban et al., “A novel modified sine-cosine optimized MPPT algorithm for grid
integrated PV system under real operating conditions,” IEEE Access, vol. 7, pp. 10467–10477,
2019.
[2] N. Priyadarshi, S. Padmanaban, M. S. Bhaskar, F. Blaabjerg, and A. Sharma, “Fuzzy
SVPWM-based inverter control realisation of grid integrated photovoltaicwind system with
fuzzy particle swarm optimisation maximum power point tracking algorithm for a gridconnected](data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7)
Recommended
Development of wind and solar based ac microgrid with power quality improveme...
This work proposes a microgrid (μ-grid) integrating wind and solar photovoltaic (PV) resources, along with the battery energy storage (BES) to the three phase grid feeding the nonlinear load. The μ-grid disconcerted by probabilistic nonlinear time dependent parameters and their effects are compensated by cohesive controllers used for utility grid side voltage source converter (GVSC) and machine side VSC (MVSC). The switching controls and the reconfigurability of the μ-grid are addressed on imperative aspects of improving power quality (PQ), power reliability, nonlinear load compensation and economic utilization of resources. The nonlinear load compensation and PQ enhancement are achieved by executing modified version of the adaptive filtering technique including “momentum” based least mean square (MLMS) control technique, utilized for providing the switching control signals to the GVSC. It utilizes two preceding gradient weights for obtaining updated weight thereby improving the convergence rate and overcoming the limitation of conventional control of the same family. The MVSC acquires its switching signals from conventional vector control scheme and the encoderless estimation of speed and rotor position of the synchronous generator (SG) driven by wind turbine through back electromotive force control technique. The external environmental disturbances are overcome by utilizing perturb and observe (P&O) maximum power point (MPP) for wind optimal power extraction and adaptive P&O with variable perturbation step size for solar MPP estimation. Test results are obtained from the laboratory prototype under steady state and dynamic conditions including altering wind speed, intermittent solar insolation and variable load conditions. The PQ issues are addressed and investigated successfully.
A New Circuit of Modular Multilevel Inverter for Grid-Connected Photovoltaic ...
This study presents a new circuit topology of the Modular Multilevel Converter (MMC) which is deployed for photovoltaic grid applications. In the conventional MMC, two arm inductors are placed in each phase to limit the circulating current. In the proposed topology, the inductors are replaced by a transformer. The proposed circuit gives a 50% reduction of the voltage rating of the power devices and the capacitors in comparison with the conventional MMC. The required dc-link voltage which is fed directly by PV panels is also reduced by half. The paper presents a PWM method to control the solar inverter output voltage. The proposed concept is confirmed through simulation and experimental results.
A simplified phase shift pwm-based feedforward distributed mppt method for gr...
The modularity and decreased filter size properties have made cascaded multilevel inverters (MLIs) more applicable than conventional two-level inverters, especially in high and medium power photovoltaic (PV) applications. However, partial shading of PV modules will affect negatively the output power of the unshaded modules. There are several existing solutions in the literature to address this challenge, however almost all of them suffer from complex implementations, low efficiency, and high cost. This paper presents a new simplified feedforward distributed maximum power point tracking (MPPT) method for three-phase grid-connected cascaded MLIs. The cascaded MLI provides a modular, and highly efficient single stage power conversion for PV systems. The proposed distributed MPPT method is depending on the phase-shift pulse width modulation (PSPWM) method with a simplified implementation. The proposed method is developing a feedforward signal that is proportional to the maximum power of the individual module. Then, the current controller, and the modulating signal are multiplied with the proportionality factor of the module maximum power. Furthermore, a modified modulation compensation method without using proportional-integral (PI) controllers is introduced to solve the problem of the unbalanced three-phase PV output currents that results from PV power mismatches and shading. A case study is implemented for 15 kW PV system to investigate the performance of the proposed method. In addition, comprehensive comparisons with the previous attempts in the literature are provided to verify the superior performance of the new proposed control method.
ANALYSIS OF DISCRETE & SPACE VECTOR PWM CONTROLLED HYBRID ACTIVE FILTERS FOR ...
It is known from the fact that Harmonic Distortion is one of the main power quality problems frequently encountered by the utilities. The harmonic problems in the power supply are caused by the non-linear characteristic based loads. The presence of harmonics leads to transformer heating, electromagnetic interference and solid state device mal-functioning. Hence keeping in view of the above concern, research has been carried out to mitigate harmonics. This paper presents an analysis and control methods for hybrid active power filter using Discrete Pulse Width Modulation and Space Vector Pulse Width Modulation (SVPWM) for Power Conditioning in distribution systems. The Discrete PWM has the function of voltage stability, and harmonic suppression. The reference current can be calculated by ‘d-q’ transformation. In SVPWM technique, the Active Power Filter (APF) reference voltage vector is generated instead of the reference current, and the desired APF output voltage is generated by SVPWM. The THD will be decreased significantly by SVPWM technique than the Discrete PWM technique based Hybrid filters. Simulations are carried out for the two approaches by using MATLAB, it is observed that the %THD has been improved from 1.79 to 1.61 by the SVPWM technique.
Novel High Performance Stand Alone Solar PV System with High Gain, High Effic...
This paper proposes a novel 3- stand-alone solar PV system configuration that uses high gain, high efficiency (96%) dc-dc converters both in the forward power stage as well as the bidirectional battery interface. The high voltage gain converters enable the use of low voltage PV and battery sources. This results in minimization of partial shading and parasitic capacitance effects on the PV source. Series connection of a large number of battery modules is obviated, preventing the overcharging and deep discharging issues that reduce the battery life. Also, the proposed configuration facilitates "required power tracking (RPT)" of the PV source as per the load requirements eliminating the use of expensive and 'difficult to manage' dump loads. High performance inverter operation is achieved through abc to dq reference frame transformation, which helps in generating precise information about the load's active power component for RPT, regulation of ac output voltage and minimization of control complexity. Inverter output voltage is regulated by controlling the modulation index of sinusoidal pulse width modulation, resulting in a stable and reliable system operation. The active power demand is controlled by regulating the dc link voltage. All the analytical, simulation and experimental results of this work are presented.
Model predictive control of pv sources in a smart dc distribution system maxi...
In a dc distribution system, where multiple power sources supply a common bus, current sharing is an important issue. When renewable energy resources are considered, such as photovoltaic (PV), dc/dc converters are needed to decouple the source voltage, which can vary due to operating conditions and maximum power point tracking (MPPT), from the dc bus voltage. Since different sources may have different power delivery capacities that may vary with time, coordination of the interface to the bus is of paramount importance to ensure reliable system operation. Further, since these sources are most likely distributed throughout\ the system, distributed controls are needed to ensure a robust and fault tolerant control system. This paper presents a model predictive control-based MPPT and model predictive control-based droop current regulator to interface PV in smart dc distribution systems. Back-to-back dc/dc converters control both the input current from the PV module and the droop characteristic of the output current injected into the distribution bus. The predictive controller speeds up both of the control loops, since it predicts and corrects error before the switching signal is applied to the respective converter.
Comparison of Modulation Techniques for Matrix Converter
Matrix Converters can directly convert an ac power supply of fixed voltage into an ac voltage of variable amplitude and frequency. Matrix Converter is a single stage converter. The matrix converters can contribute to the realization of low volume, sinusoidal input current, bidirectional power flow and lack of bulky reactive elements. All the reasons lead to the development of matrix converter. Based on the control techniques used in the matrix converter, the performance varies. So this paper analyses the performance of matrix converter with three different modulation techniques such as PWM, SVPWM and SVM. The basic principle and switching sequence of these modulation techniques are presented in this paper. The output voltage, output current waveforms, voltage transfer ratio and THD spectrum of switching waveforms connected to RL load are analyzed by using Matlab/Simulink software. The simulated results are analyzed and show that the THD is better for SVM technique.
Power Quality Assessment of Voltage Positive Feedback Based Islanding Detecti...
Islanding refers to a condition where distributed generators (DGs) inject power solely to the local load after electrical separation from power grid. Several islanding detection methods (IDMs) categorized into remote, active, and passive groups have been reported to detect this undesirable state. In active techniques, a disturbance is injected into the DG’s controller to drift a local yardstick out of the permissible range. Although this disturbance leads to more effective detections even in well-balanced island, it raises the total harmonic distortion (THD) of the output current under the normal operation conditions. This paper analyzes the power quality aspect of the modified sliding mode controller as a new active IDM for grid-connected photovoltaic system (GCPVS) with a string inverter. Its performance is compared with the voltage positive feedback (VPF) method, a well-known active IDM. This evaluation is carried out for a 1 kWp GCPVS in MATLAB/Simulink platform by measuring the output current harmonics and THD as well as the efficiency under various penetration and disturbance levels. The output results demonstrate that since the proposed disturbance changes the amplitude of the output current, it does not generate harmonics/subharmonics. Thereby, it has a negligible adverse effect on power quality. It is finally concluded that the performance of the sliding mode-based IDM is reliable from the standpoints of islanding detection and power quality.
Recommended
Development of wind and solar based ac microgrid with power quality improveme...
This work proposes a microgrid (μ-grid) integrating wind and solar photovoltaic (PV) resources, along with the battery energy storage (BES) to the three phase grid feeding the nonlinear load. The μ-grid disconcerted by probabilistic nonlinear time dependent parameters and their effects are compensated by cohesive controllers used for utility grid side voltage source converter (GVSC) and machine side VSC (MVSC). The switching controls and the reconfigurability of the μ-grid are addressed on imperative aspects of improving power quality (PQ), power reliability, nonlinear load compensation and economic utilization of resources. The nonlinear load compensation and PQ enhancement are achieved by executing modified version of the adaptive filtering technique including “momentum” based least mean square (MLMS) control technique, utilized for providing the switching control signals to the GVSC. It utilizes two preceding gradient weights for obtaining updated weight thereby improving the convergence rate and overcoming the limitation of conventional control of the same family. The MVSC acquires its switching signals from conventional vector control scheme and the encoderless estimation of speed and rotor position of the synchronous generator (SG) driven by wind turbine through back electromotive force control technique. The external environmental disturbances are overcome by utilizing perturb and observe (P&O) maximum power point (MPP) for wind optimal power extraction and adaptive P&O with variable perturbation step size for solar MPP estimation. Test results are obtained from the laboratory prototype under steady state and dynamic conditions including altering wind speed, intermittent solar insolation and variable load conditions. The PQ issues are addressed and investigated successfully.
A New Circuit of Modular Multilevel Inverter for Grid-Connected Photovoltaic ...
This study presents a new circuit topology of the Modular Multilevel Converter (MMC) which is deployed for photovoltaic grid applications. In the conventional MMC, two arm inductors are placed in each phase to limit the circulating current. In the proposed topology, the inductors are replaced by a transformer. The proposed circuit gives a 50% reduction of the voltage rating of the power devices and the capacitors in comparison with the conventional MMC. The required dc-link voltage which is fed directly by PV panels is also reduced by half. The paper presents a PWM method to control the solar inverter output voltage. The proposed concept is confirmed through simulation and experimental results.
A simplified phase shift pwm-based feedforward distributed mppt method for gr...
The modularity and decreased filter size properties have made cascaded multilevel inverters (MLIs) more applicable than conventional two-level inverters, especially in high and medium power photovoltaic (PV) applications. However, partial shading of PV modules will affect negatively the output power of the unshaded modules. There are several existing solutions in the literature to address this challenge, however almost all of them suffer from complex implementations, low efficiency, and high cost. This paper presents a new simplified feedforward distributed maximum power point tracking (MPPT) method for three-phase grid-connected cascaded MLIs. The cascaded MLI provides a modular, and highly efficient single stage power conversion for PV systems. The proposed distributed MPPT method is depending on the phase-shift pulse width modulation (PSPWM) method with a simplified implementation. The proposed method is developing a feedforward signal that is proportional to the maximum power of the individual module. Then, the current controller, and the modulating signal are multiplied with the proportionality factor of the module maximum power. Furthermore, a modified modulation compensation method without using proportional-integral (PI) controllers is introduced to solve the problem of the unbalanced three-phase PV output currents that results from PV power mismatches and shading. A case study is implemented for 15 kW PV system to investigate the performance of the proposed method. In addition, comprehensive comparisons with the previous attempts in the literature are provided to verify the superior performance of the new proposed control method.
ANALYSIS OF DISCRETE & SPACE VECTOR PWM CONTROLLED HYBRID ACTIVE FILTERS FOR ...
It is known from the fact that Harmonic Distortion is one of the main power quality problems frequently encountered by the utilities. The harmonic problems in the power supply are caused by the non-linear characteristic based loads. The presence of harmonics leads to transformer heating, electromagnetic interference and solid state device mal-functioning. Hence keeping in view of the above concern, research has been carried out to mitigate harmonics. This paper presents an analysis and control methods for hybrid active power filter using Discrete Pulse Width Modulation and Space Vector Pulse Width Modulation (SVPWM) for Power Conditioning in distribution systems. The Discrete PWM has the function of voltage stability, and harmonic suppression. The reference current can be calculated by ‘d-q’ transformation. In SVPWM technique, the Active Power Filter (APF) reference voltage vector is generated instead of the reference current, and the desired APF output voltage is generated by SVPWM. The THD will be decreased significantly by SVPWM technique than the Discrete PWM technique based Hybrid filters. Simulations are carried out for the two approaches by using MATLAB, it is observed that the %THD has been improved from 1.79 to 1.61 by the SVPWM technique.
Novel High Performance Stand Alone Solar PV System with High Gain, High Effic...
This paper proposes a novel 3- stand-alone solar PV system configuration that uses high gain, high efficiency (96%) dc-dc converters both in the forward power stage as well as the bidirectional battery interface. The high voltage gain converters enable the use of low voltage PV and battery sources. This results in minimization of partial shading and parasitic capacitance effects on the PV source. Series connection of a large number of battery modules is obviated, preventing the overcharging and deep discharging issues that reduce the battery life. Also, the proposed configuration facilitates "required power tracking (RPT)" of the PV source as per the load requirements eliminating the use of expensive and 'difficult to manage' dump loads. High performance inverter operation is achieved through abc to dq reference frame transformation, which helps in generating precise information about the load's active power component for RPT, regulation of ac output voltage and minimization of control complexity. Inverter output voltage is regulated by controlling the modulation index of sinusoidal pulse width modulation, resulting in a stable and reliable system operation. The active power demand is controlled by regulating the dc link voltage. All the analytical, simulation and experimental results of this work are presented.
Model predictive control of pv sources in a smart dc distribution system maxi...
In a dc distribution system, where multiple power sources supply a common bus, current sharing is an important issue. When renewable energy resources are considered, such as photovoltaic (PV), dc/dc converters are needed to decouple the source voltage, which can vary due to operating conditions and maximum power point tracking (MPPT), from the dc bus voltage. Since different sources may have different power delivery capacities that may vary with time, coordination of the interface to the bus is of paramount importance to ensure reliable system operation. Further, since these sources are most likely distributed throughout\ the system, distributed controls are needed to ensure a robust and fault tolerant control system. This paper presents a model predictive control-based MPPT and model predictive control-based droop current regulator to interface PV in smart dc distribution systems. Back-to-back dc/dc converters control both the input current from the PV module and the droop characteristic of the output current injected into the distribution bus. The predictive controller speeds up both of the control loops, since it predicts and corrects error before the switching signal is applied to the respective converter.
Comparison of Modulation Techniques for Matrix Converter
Matrix Converters can directly convert an ac power supply of fixed voltage into an ac voltage of variable amplitude and frequency. Matrix Converter is a single stage converter. The matrix converters can contribute to the realization of low volume, sinusoidal input current, bidirectional power flow and lack of bulky reactive elements. All the reasons lead to the development of matrix converter. Based on the control techniques used in the matrix converter, the performance varies. So this paper analyses the performance of matrix converter with three different modulation techniques such as PWM, SVPWM and SVM. The basic principle and switching sequence of these modulation techniques are presented in this paper. The output voltage, output current waveforms, voltage transfer ratio and THD spectrum of switching waveforms connected to RL load are analyzed by using Matlab/Simulink software. The simulated results are analyzed and show that the THD is better for SVM technique.
Power Quality Assessment of Voltage Positive Feedback Based Islanding Detecti...
Islanding refers to a condition where distributed generators (DGs) inject power solely to the local load after electrical separation from power grid. Several islanding detection methods (IDMs) categorized into remote, active, and passive groups have been reported to detect this undesirable state. In active techniques, a disturbance is injected into the DG’s controller to drift a local yardstick out of the permissible range. Although this disturbance leads to more effective detections even in well-balanced island, it raises the total harmonic distortion (THD) of the output current under the normal operation conditions. This paper analyzes the power quality aspect of the modified sliding mode controller as a new active IDM for grid-connected photovoltaic system (GCPVS) with a string inverter. Its performance is compared with the voltage positive feedback (VPF) method, a well-known active IDM. This evaluation is carried out for a 1 kWp GCPVS in MATLAB/Simulink platform by measuring the output current harmonics and THD as well as the efficiency under various penetration and disturbance levels. The output results demonstrate that since the proposed disturbance changes the amplitude of the output current, it does not generate harmonics/subharmonics. Thereby, it has a negligible adverse effect on power quality. It is finally concluded that the performance of the sliding mode-based IDM is reliable from the standpoints of islanding detection and power quality.
A three phase grid tied spv system with adaptive dc link voltage for cpi volt...
This paper deals with a three-phase two-stage grid tied SPV (solar photo-voltaic) system. The first stage is a boost converter, which serves the purpose of MPPT (maximum power point tracking) and feeding the extracted solar energy to the DC link of the PV inverter, whereas the second stage is a two-level VSC (voltage source converter) serving as PV inverter which feeds power from a boost converter into the grid. The proposed system uses an adaptive DC link voltage which is made adaptive by adjusting reference DC link voltage according to CPI (common point of interconnection) voltage. The adaptive DC link voltage control helps in the reduction of switching power losses. A feed forward term for solar contribution is used to improve the dynamic response. The system is tested considering realistic grid voltage variations for under voltage and over voltage. The performance improvement is verified experimentally. The proposed system is advantageous not only in cases of frequent and sustained under voltage (as in the cases of far radial ends of Indian grid) but also in case of normal voltages at CPI. The THD (total harmonics distortion) of grid current has been found well under the limit of an IEEE-519 standard.
Power quality improvement in distribution network using DSTATCOM with battery...
The distribution static compensator (DSTATCOM) provides fast control of active and reactive powers to enable load compensation, harmonics current elimination, voltage flicker mitigation, voltage and frequency regulation. This paper presents power quality improvement technique in the presence of grid disturbances and wind energy penetration using DSTATCOM with battery energy storage system. DSTATCOM control is provided based on synchronous reference frame theory. A modified IEEE 13 bus test feeder with DSTATCOM and wind generator is used for the study. Power quality events during grid disturbances such as feeder tripping and re-closing, voltage sag, swell and load switching have been studied in association with DSTATCOM. The power quality disturbances due to wind generator outage, synchronization and wind speed variations have also been investigated. The study has been carried out using MATLAB/SIMULINK and the simulation results are compared with real time results obtained by the use of real time digital simulator (RTDS) for validating the effectiveness of proposed methodology. The proposed method has been proved to be effective in improvement of power quality with all disturbances stated above.
A novel online fuzzy control method of static var compensation for an effecti...
The Flexible AC Transmission System (FACTS) technology is a promising technology to achieve complete deregulation of Power System i.e. Generation, Transmission and Distribution as the complete individual units. FACTS is based on power electronic devices, used to enhance the existing transmission capabilities in order to make the transmission system flexible and independent in operation. The loading capability of transmission system can also be enhanced nearer to its thermal limit without affecting the stability. Complete closed-loop smooth control of reactive power can be achieved using shunt connected FACTS devices. Static VAR Compensator (SVC) is one of the shunt connected FACTS devices, which can be utilized for the purpose of reactive power compensation. As the Intelligent FACTS devices make them adaptable, it is emerging as the present state of the art technology. This paper presents the design and simulation of the Fuzzy logic control to vary firing angle of SVC in order to achieve better, smooth and adaptive control of reactive power in transmission systems. The design, modeling and simulations are carried out for the λ/8 Transmission line by placing the compensation at the receiving end (load end) and the results obtained demonstrates the effectiveness of the proposed method.
Improving the Dynamic Performance of Wind Farms with STATCOM
When integrated to the power system, large wind farms can pose voltage control issues among
other problems. A thorough study is needed to identify the potential problems and to develop
measures to mitigate them. Although integration of high levels of wind power into an existing
transmission system does not require a major redesign, it necessitates additional control and
compensating equipment to enable (fast) recovery from severe system disturbances. The use of a
Static Synchronous Compensator (STATCOM) near a wind farm is investigated for the purpose
of stabilizing the grid voltage after grid-side disturbance such as a three phase short circuit fault.
The strategy focuses on a fundamental grid operational requirement to maintain proper voltages
at the point of common coupling by regulating the voltage. The DC voltage at individual wind
turbine (WT) inverters is also stabilized to facilitate continuous operation of wind turbines
during disturbances.
Power Quality Improvement of Grid-Connected Photovoltaic Systems Using Trans-...
Voltage-source inverter has been used widely in traditional photovoltaic systems which have limitations. To overcome, Z-source inverter has been introduced. In spite of all the features introduced in Z-source inverter, its configuration has been improved over the years, like trans-Z-source inverter which has added advantages compared to traditional inverters, namely buck–boost feature, lesser passive elements, and higher voltage boost gain. In this paper, photovoltaic arrays are connected to the grid via the trans-Z-source inverter with the aim of improving its power quality. Moreover, the shoot through duty ratio is kept constant in the switching control method to add features like lower voltage stress (higher reliability), lower total harmonic distortion (lower maintenance cost), and higher voltage boost ratio. To evaluate the precision of the proposed system, the photovoltaic system is simulated on a standard grid and under partial shading condition which brings about voltage sag, and hence, a dynamic voltage restorer is used to mitigate voltage sag. Simulation results are presented to verify the validation of the proposed photovoltaic system in terms of voltage and current THD reducing 78.2% and 19.7%, respectively.
Statcom for improved dynamic performance of wind farms in power grid
Application of FACTS controller called Static Synchronous Compensator STATCOM to improve the performance of power grid with Wind Farms is investigated .The essential feature of the STATCOM is that it has the ability to absorb or inject fastly the reactive power with power grid . Therefore the voltage regulation of the power grid with STATCOM FACTS device is achieved. Moreover restoring the stability of the power system having wind farm after occurring
severe disturbance such as faults or wind farm mechanical power variation is obtained with STATCOM controller . The dynamic model of the power system having wind farm controlled by
proposed STATCOM is developed . To Validate the powerful of the STATCOM FACTS controller , the studied power system is simulated and subjected to different severe disturbances . The results prove the effectiveness of the proposed STATCOM controller in terms of fast damping the power system oscillations and restoring the power system stability .
Power Quality Improvement in Solar Fed Cascaded Multilevel Inverter with Outp...
The presence of harmonics in solar Photo Voltaic (PV) energy conversion system results in deterioration of power quality. To address such issue, this paper aims to investigate the elimination of harmonics in a solar fed cascaded fifteen level inverter with aid of Proportional Integral (PI), Artificial Neural Network (ANN) and Fuzzy Logic (FL) based controllers. Unlike other techniques, the proposed FLC based approach helps in obtaining reduced harmonic distortions that intend to an enhancement in power quality. In addition to the power quality improvement, this paper also proposed to provide output voltage regulation in terms of maintaining voltage and frequency at the inverter output end in compatible with the grid connection requirements. The simulations are performed in the MATLAB / Simulink environment for solar fed cascaded 15 level inverter incorporating PI, ANN and FL based controllers. To exhibit the proposed technique, a 3 kWp photovoltaic plant coupled to multilevel inverter is designed and hardware is demonstrated. All the three techniques are experimentally investigated with the measurement of power quality metrics along with establishing output voltage regulation.
An integrated boost resonant converter for photovoltaic applications
Effective photovoltaic power conditioning requires efficient power conversion and accurate maximum power point tracking to counteract the effects of panel mismatch, shading, and general variance in power output during a daily cycle. In this paper, the authors propose an integrated boost resonant converter with low component count, galvanic isolation, simple control, as well as
high efficiency across a wide input and load range. Provided is a discussion of the converter synthesis, key operational features, converter design procedure, and loss analysis, as well as experimental verification by way of a 250-W prototype with a California Energy Commission efficiency of 96.8%.
Designing of multilevel dpfc to improve power quality
According to growth of electricity demand and the increased number of non-linear loads in power grids, providing a high quality electrical power should be considered. In this paper, Enhancement of power quality by using fuzzy based multilevel power flow controller (DPFC) is proposed. The DPFC is a new FACTS device, which its structure is similar to unified power flow controller (UPFC). In spite of UPFC, in DPFC the common dc-link between the shunt and series converters is eliminated and three-phase series converter is divided to several single-phase series distributed converters through the line. This eventually enables the DPFC to fully control all power system parameters. It, also, increases the reliability of the device and reduces its cost simultaneously. In recent years multi level inverters are used high power and high voltage applications .Multilevel inverter output voltage produce a staircase output waveform, this waveform look like a sinusoidal waveform leads to reduction in Harmonics. Fuzzy Logic is used for optimal designing of controller parameters. Application of Fuzzy Multilevel DPFC for reduction of Total Harmonic Distortion was presented. The simulation results show the improvement of power quality using DPFC with Fuzzy logic controller.
Irradiance-adaptive PV Module Integrated Converter for High Efficiency and Po...
The strive for efficient and cost-effective photovoltaic systems motivated the power electronic design developed here. The work resulted in a DC-DC converter for module integration and distributed maximum power point tracking (MPPT) with a novel adaptive control scheme. The latter is essential for the combined features of high energy efficiency and high power quality over a wide range of operating conditions. The switching frequency is optimally modulated as a function of solar irradiance for power conversion efficiency maximization. With the rise of irradiance, the frequency is reduced to reach the conversion efficiency target. A search algorithm is developed to determine the optimal switching frequency step. Reducing the switching frequency may, however, compromise MPPT efficiency. Furthermore, it leads to increased ripple content. Therefore, to achieve a uniform high power quality at all conditions, interleaved converter cells are adaptively activated. The overall cost is kept low by selecting components that allow for implementing the functions at low cost. Simulation results show the high value of the module integrated converter for DC standalone and microgrid applications. A 400 W prototype was implemented at 0.14 Euro/W. Testing showed efficiencies above 95% taking into account all losses from power conversion, MPPT, and measurement and control circuitry.
Single-phase solar PV system with battery and exchange of power in grid-conne...
A grid tied photovoltaic (PV) power conversion topology is presented in this study with a novel scheme of resynchronization to the grid. This scheme serves the purpose of supplying continuous power to the load along with feeding power to the grid. The control approach helps in mitigation of harmonics and improving the power quality while extracting the optimum power from the PV array. Depending on the availability of grid voltage, the proposed configuration is controlled using three approaches, defined as grid current control, Point of Common Coupling (PCC) voltage control and intentional islanding with re-synchronisation. A simple proportional integral controller manages the grid current, load voltage, battery current and DC Direct Current (DC) link voltage within these modes. Moreover, a control scheme for quick and smooth transitions among the modes is described. The robustness of the system under erratic behaviour of solar insolation, load power and disturbances in grid supply makes it a suitable choice for a residential application. The control, design and simulation results are presented to demonstrate the satisfactory operation of the proposed system.
Three phase transformerless shunt active power filter with reduced switch cou...
Shunt active power filter is the preeminent solution against nonlinear loads, current harmonics and power quality problems. APF topologies for harmonic compensation use numerous high-power rating components and are therefore disadvantageous. Hybrid topologies combining low-power rating APF with passive filters are used to reduce the power rating of voltage source inverter. Hybrid APF topologies for high-power rating systems use a transformer with large numbers of passive components. In this paper, a novel four-switch two-leg VSI topology for a three-phase SAPF is proposed for reducing the system cost and size. The proposed topology comprises a two-arm bridge structure, four switches, coupling inductors, and sets of LC PFs. The third leg of the three-phase VSI is removed by eliminating the set of power switching devices, thereby directly connecting the phase with the negative terminals of the dc-link capacitor. The proposed topology enhances the harmonic compensation capability and provides complete reactive power compensation compared with conventional APF topologies. The new experimental prototype is tested in the laboratory to verify the results in terms of total harmonic distortion, balanced supply current, and harmonic compensation, following the IEEE-519 standard.
Control strategy for power flow management in a pv system supplying dc loads
The growing concern for energy saving has increased the usage of LED-based street lights, electronic chokes, compact fluorescent lamps, and inverter-fed drives. Hence, the load profile seen by the electrical grid is undergoing a notable change as these devices have to operate from a dc source. Photovoltaics (PV) being a major energy source, the aforementioned loads can be connected directly to the dc bus. A grid-connected PV system involves a power source (PV array), a power sink (load), and two power sources/sink (utility and battery), and hence, a power
flow management system is required to balance the power flow among these sources. One such system is developed for selecting the operating mode of the bidirectional converter by sensing the battery voltage. The viability of the scheme has been ascertained by performing experimental studies on a laboratory prototype. The control strategy is digitally implemented on an Altera Cyclone II Field Programmable Gate Array (FPGA) board, and the algorithm is verified for different modes of operation by varying the load. Experimental results are presented to bring out
the usefulness of the control strategy.
Power Quality Assessment of Voltage Positive Feedback Based Islanding Detecti...
Islanding refers to a condition where distributed generators (DGs) inject power solely to the local load after electrical separation from power grid. Several islanding detection methods (IDMs) categorized into remote, active, and passive groups have been reported to detect this undesirable state. In active techniques, a disturbance is injected into the DG’s controller to drift a local yardstick out of the permissible range. Although this disturbance leads to more effective detections even in well-balanced island, it raises the total harmonic distortion (THD) of the output current under the normal operation conditions. This paper analyzes the power quality aspect of the modified sliding mode controller as a new active IDM for grid-connected photovoltaic system (GCPVS) with a string inverter. Its performance is compared with the voltage positive feedback (VPF) method, a well-known active IDM. This evaluation is carried out for a 1 kWp GCPVS in MATLAB/Simulink platform by measuring the output current harmonics and THD as well as the efficiency under various penetration and disturbance levels. The output results demonstrate that since the proposed disturbance changes the amplitude of the output current, it does not generate harmonics/subharmonics. Thereby, it has a negligible adverse effect on power quality. It is finally concluded that the performance of the sliding mode-based IDM is reliable from the standpoints of islanding detection and power quality.
Design and Control of Wind integrated Shunt Active Power Filter to Improve Po...
In this paper wind energy conservation system (WECS) with shunt active power filter (SAPF) is proposed for harmonics elimination, power factor correction, reactive power compensation and grid current balancing. Adaptive neuro fuzzy inference system (ANFIS) based controller is implemented at WECS side to control the boost converter to achieve MPP and at SAPF sides to minimize voltage variations and enhance power quality. Here, synchronous reference frame (SRF) theory based reference current generation technique is employed in SAPF. The proposed scheme is implemented in MATLAB/Simulink. The results confirm that this method has better performance and can maintain total harmonic distortion (THD) level of the system within the IEEE standard 519.
A Unified Control and Power Management Scheme for PV-Battery-Based Hybrid Mic...
Battery storage is usually employed in Photovoltaic (PV) system to mitigate the power fluctuations due to the characteristics of PV panels and solar irradiance. Control schemes for PV-battery systems must be able to stabilize the bus voltages as well as to control the power flows flexibly. This paper proposes a comprehensive control and power management system (CAPMS) for PV-battery-based hybrid microgrids with both AC and DC buses, for both grid-connected and islanded modes. The proposed CAPMS is successful in regulating the DC and AC bus voltages and frequency stably, controlling the voltage and power of each unit flexibly, and balancing the power flows in the systems automatically under different operating circumstances, regardless of disturbances from switching operating modes, fluctuations of irradiance and temperature, and change of loads. Both simulation and experimental case studies are carried out to verify the performance of the proposed method.
A New Design Method of an LCL Filter Applied in Active DC-Traction Substations
This paper concentrates on the LCL filter with damping resistance intended to connect the shunt active power filter of an active DC-traction substation to the point of common coupling with the transmission grid. In order to find design conditions and conceive a design algorithm, attention is directed to the transfer functions related to currents and the associated frequency response. The mathematical foundation of the design method is based on the meeting the requirements related to the significant attenuation of the high-frequency switching current, concurrently with the unalterated flow of the current that needs to be compensated by active filtering. It is pointed out that there are practical limitations and a compromise must be made between the two requirements. To quantify the extent to which the harmonics to be compensated are influenced by imposing the magnitude response at both highest harmonic frequency to be compensated and switching frequency, a performance indicator is defined. As an additional design criterion, the damping power losses are taken into consideration. The validity and effectiveness of the proposed method are proved by simulation results and experimental tests on a laboratory test bench of small scale reproducing the specific conditions of a DC-traction substation with six-pulse diode rectifier.
Multifunctional grid tied pv system using modified klms control
This paper deals with the modified kernel least mean square (KLMS) control strategy in double-stage, solar photovoltaic (PV) grid tied system to enhance the power quality at common coupling point (CCP). This proposed control algorithm has less oscillations, fast convergence, fast dynamic response and good steady state performance. A control strategy is used to extract the fundamental active current component of load and generates reference grid current for a DC-AC converter. The proposed modified KLMS control mitigates multiple power quality concerns such as harmonics reduction, unity power factor and load balancing. The dynamic performance of proposed system is confirmed into the MATLAB\Simulink environment. Test results on hardware implementation are presented at varying solar irradiation levels and load unbalancing. Test results are found satisfactory and total harmonic distortion (THD) of the grid currents are observed well within the IEEE-519 standard.
An improved transformerless inverter for
Leading project maker in Nashik, Electrical project in nashik goelectromeh.in, Electronic project in nashik goelectromeh.in, computer project in nashik, Electrical project engineering project in nashik goelectromeh.in, Electronic project engineering project in nashik goelectromeh.in, Computer project engineering project in nashik goelectromeh.in,
Electrical project Diploma project in nashik goelectromeh.in, Electronic project Diploma project in nashik goelectromeh.in, Computer project Diploma project in nashik goelectromeh.in.
Maximum power extraction from wind energy system based on fuzzy logic control
This paper proposes a variable speed control scheme for grid-connected wind energy conversion system (WECS) using permanent magnet synchronous generator (PMSG). The control algorithm tracks the maximum power for wind speeds below rated speed of wind turbines and ensures the power will not go over the rated power for wind speeds over the rated value. The control algorithm employs fuzzy logic controller (FLC) to effectively do this target. The wind turbine is connected to the grid via back-to-back PWM-VSC. Two effective computer simulation packages (PSIM and Simulink) are used to carry out the simulation effectively. The control system has two controllers for generator side and grid side converters. The main function of the generator side controller is to track the maximum power through controlling the rotational speed of the wind turbine using FLC. In the grid side converter, active and reactive power control has been achieved by controlling q-axis and d-axis current components, respectively. The d-axis current is set at zero for unity power factor and the q-axis current is controlled to deliver the power flowing from the dc-link to the electric utility grid.
Front end buck rectifier with reduced filter size and single-loop control
This paper presents a transformerless solution for front-end rectification, which is particularly suitable for traction applications, requiring high voltages to be stepped down to appropriate dc voltage. The proposed topology is based on pulse widthmodulation buck rectifier (current source inverter topology) and is capable of rectification and stepping down of single-phase ac supply, in a single stage. A new control scheme is proposed to achieve constant dc output voltage and sinusoidal source current, irrespective of large ripples in the dc inductor current. The proposed scheme is configured in single-loop voltage control mode. The relevant small-signal model is derived from the large-signal model using multi order decomposition. An elaborate procedure of dc filter design is discussed, for circuit operation with minimum energy storage. All analytical results are validated by numerical simulation for sinusoidal and distorted source voltage. Experimental verification is achieved through a 1.2-kW grid-connected laboratory prototype.
Performance enhancement of shunt active power filter with fuzzy and hysteresi...
This paper proposes fuzzy and hysteresis controllers based three phase Shunt Active Power Filter
for current harmonic compensation to improve the performance of 3ɸ supply system feeding
non- linear loads. The Shunt Active Power Filter is used to eliminate current harmonics. The dc
link control strategy is based on the fuzzy logic controller. Gating pulses for the Shunt Active
Filter is generated using Hysteresis current controller based Pulse width modulation technique.
The proposed model is simulated in MATLAB/SIMULINK. Simulation results show that the
dynamic behavior is better than the conventional Proportional- Integral (PI) controller and is
found to be more robust for changes in load.
More Related Content
What's hot
A three phase grid tied spv system with adaptive dc link voltage for cpi volt...
This paper deals with a three-phase two-stage grid tied SPV (solar photo-voltaic) system. The first stage is a boost converter, which serves the purpose of MPPT (maximum power point tracking) and feeding the extracted solar energy to the DC link of the PV inverter, whereas the second stage is a two-level VSC (voltage source converter) serving as PV inverter which feeds power from a boost converter into the grid. The proposed system uses an adaptive DC link voltage which is made adaptive by adjusting reference DC link voltage according to CPI (common point of interconnection) voltage. The adaptive DC link voltage control helps in the reduction of switching power losses. A feed forward term for solar contribution is used to improve the dynamic response. The system is tested considering realistic grid voltage variations for under voltage and over voltage. The performance improvement is verified experimentally. The proposed system is advantageous not only in cases of frequent and sustained under voltage (as in the cases of far radial ends of Indian grid) but also in case of normal voltages at CPI. The THD (total harmonics distortion) of grid current has been found well under the limit of an IEEE-519 standard.
Power quality improvement in distribution network using DSTATCOM with battery...
The distribution static compensator (DSTATCOM) provides fast control of active and reactive powers to enable load compensation, harmonics current elimination, voltage flicker mitigation, voltage and frequency regulation. This paper presents power quality improvement technique in the presence of grid disturbances and wind energy penetration using DSTATCOM with battery energy storage system. DSTATCOM control is provided based on synchronous reference frame theory. A modified IEEE 13 bus test feeder with DSTATCOM and wind generator is used for the study. Power quality events during grid disturbances such as feeder tripping and re-closing, voltage sag, swell and load switching have been studied in association with DSTATCOM. The power quality disturbances due to wind generator outage, synchronization and wind speed variations have also been investigated. The study has been carried out using MATLAB/SIMULINK and the simulation results are compared with real time results obtained by the use of real time digital simulator (RTDS) for validating the effectiveness of proposed methodology. The proposed method has been proved to be effective in improvement of power quality with all disturbances stated above.
A novel online fuzzy control method of static var compensation for an effecti...
The Flexible AC Transmission System (FACTS) technology is a promising technology to achieve complete deregulation of Power System i.e. Generation, Transmission and Distribution as the complete individual units. FACTS is based on power electronic devices, used to enhance the existing transmission capabilities in order to make the transmission system flexible and independent in operation. The loading capability of transmission system can also be enhanced nearer to its thermal limit without affecting the stability. Complete closed-loop smooth control of reactive power can be achieved using shunt connected FACTS devices. Static VAR Compensator (SVC) is one of the shunt connected FACTS devices, which can be utilized for the purpose of reactive power compensation. As the Intelligent FACTS devices make them adaptable, it is emerging as the present state of the art technology. This paper presents the design and simulation of the Fuzzy logic control to vary firing angle of SVC in order to achieve better, smooth and adaptive control of reactive power in transmission systems. The design, modeling and simulations are carried out for the λ/8 Transmission line by placing the compensation at the receiving end (load end) and the results obtained demonstrates the effectiveness of the proposed method.
Improving the Dynamic Performance of Wind Farms with STATCOM
When integrated to the power system, large wind farms can pose voltage control issues among
other problems. A thorough study is needed to identify the potential problems and to develop
measures to mitigate them. Although integration of high levels of wind power into an existing
transmission system does not require a major redesign, it necessitates additional control and
compensating equipment to enable (fast) recovery from severe system disturbances. The use of a
Static Synchronous Compensator (STATCOM) near a wind farm is investigated for the purpose
of stabilizing the grid voltage after grid-side disturbance such as a three phase short circuit fault.
The strategy focuses on a fundamental grid operational requirement to maintain proper voltages
at the point of common coupling by regulating the voltage. The DC voltage at individual wind
turbine (WT) inverters is also stabilized to facilitate continuous operation of wind turbines
during disturbances.
Power Quality Improvement of Grid-Connected Photovoltaic Systems Using Trans-...
Voltage-source inverter has been used widely in traditional photovoltaic systems which have limitations. To overcome, Z-source inverter has been introduced. In spite of all the features introduced in Z-source inverter, its configuration has been improved over the years, like trans-Z-source inverter which has added advantages compared to traditional inverters, namely buck–boost feature, lesser passive elements, and higher voltage boost gain. In this paper, photovoltaic arrays are connected to the grid via the trans-Z-source inverter with the aim of improving its power quality. Moreover, the shoot through duty ratio is kept constant in the switching control method to add features like lower voltage stress (higher reliability), lower total harmonic distortion (lower maintenance cost), and higher voltage boost ratio. To evaluate the precision of the proposed system, the photovoltaic system is simulated on a standard grid and under partial shading condition which brings about voltage sag, and hence, a dynamic voltage restorer is used to mitigate voltage sag. Simulation results are presented to verify the validation of the proposed photovoltaic system in terms of voltage and current THD reducing 78.2% and 19.7%, respectively.
Statcom for improved dynamic performance of wind farms in power grid
Application of FACTS controller called Static Synchronous Compensator STATCOM to improve the performance of power grid with Wind Farms is investigated .The essential feature of the STATCOM is that it has the ability to absorb or inject fastly the reactive power with power grid . Therefore the voltage regulation of the power grid with STATCOM FACTS device is achieved. Moreover restoring the stability of the power system having wind farm after occurring
severe disturbance such as faults or wind farm mechanical power variation is obtained with STATCOM controller . The dynamic model of the power system having wind farm controlled by
proposed STATCOM is developed . To Validate the powerful of the STATCOM FACTS controller , the studied power system is simulated and subjected to different severe disturbances . The results prove the effectiveness of the proposed STATCOM controller in terms of fast damping the power system oscillations and restoring the power system stability .
Power Quality Improvement in Solar Fed Cascaded Multilevel Inverter with Outp...
The presence of harmonics in solar Photo Voltaic (PV) energy conversion system results in deterioration of power quality. To address such issue, this paper aims to investigate the elimination of harmonics in a solar fed cascaded fifteen level inverter with aid of Proportional Integral (PI), Artificial Neural Network (ANN) and Fuzzy Logic (FL) based controllers. Unlike other techniques, the proposed FLC based approach helps in obtaining reduced harmonic distortions that intend to an enhancement in power quality. In addition to the power quality improvement, this paper also proposed to provide output voltage regulation in terms of maintaining voltage and frequency at the inverter output end in compatible with the grid connection requirements. The simulations are performed in the MATLAB / Simulink environment for solar fed cascaded 15 level inverter incorporating PI, ANN and FL based controllers. To exhibit the proposed technique, a 3 kWp photovoltaic plant coupled to multilevel inverter is designed and hardware is demonstrated. All the three techniques are experimentally investigated with the measurement of power quality metrics along with establishing output voltage regulation.
An integrated boost resonant converter for photovoltaic applications
Effective photovoltaic power conditioning requires efficient power conversion and accurate maximum power point tracking to counteract the effects of panel mismatch, shading, and general variance in power output during a daily cycle. In this paper, the authors propose an integrated boost resonant converter with low component count, galvanic isolation, simple control, as well as
high efficiency across a wide input and load range. Provided is a discussion of the converter synthesis, key operational features, converter design procedure, and loss analysis, as well as experimental verification by way of a 250-W prototype with a California Energy Commission efficiency of 96.8%.
Designing of multilevel dpfc to improve power quality
According to growth of electricity demand and the increased number of non-linear loads in power grids, providing a high quality electrical power should be considered. In this paper, Enhancement of power quality by using fuzzy based multilevel power flow controller (DPFC) is proposed. The DPFC is a new FACTS device, which its structure is similar to unified power flow controller (UPFC). In spite of UPFC, in DPFC the common dc-link between the shunt and series converters is eliminated and three-phase series converter is divided to several single-phase series distributed converters through the line. This eventually enables the DPFC to fully control all power system parameters. It, also, increases the reliability of the device and reduces its cost simultaneously. In recent years multi level inverters are used high power and high voltage applications .Multilevel inverter output voltage produce a staircase output waveform, this waveform look like a sinusoidal waveform leads to reduction in Harmonics. Fuzzy Logic is used for optimal designing of controller parameters. Application of Fuzzy Multilevel DPFC for reduction of Total Harmonic Distortion was presented. The simulation results show the improvement of power quality using DPFC with Fuzzy logic controller.
Irradiance-adaptive PV Module Integrated Converter for High Efficiency and Po...
The strive for efficient and cost-effective photovoltaic systems motivated the power electronic design developed here. The work resulted in a DC-DC converter for module integration and distributed maximum power point tracking (MPPT) with a novel adaptive control scheme. The latter is essential for the combined features of high energy efficiency and high power quality over a wide range of operating conditions. The switching frequency is optimally modulated as a function of solar irradiance for power conversion efficiency maximization. With the rise of irradiance, the frequency is reduced to reach the conversion efficiency target. A search algorithm is developed to determine the optimal switching frequency step. Reducing the switching frequency may, however, compromise MPPT efficiency. Furthermore, it leads to increased ripple content. Therefore, to achieve a uniform high power quality at all conditions, interleaved converter cells are adaptively activated. The overall cost is kept low by selecting components that allow for implementing the functions at low cost. Simulation results show the high value of the module integrated converter for DC standalone and microgrid applications. A 400 W prototype was implemented at 0.14 Euro/W. Testing showed efficiencies above 95% taking into account all losses from power conversion, MPPT, and measurement and control circuitry.
Single-phase solar PV system with battery and exchange of power in grid-conne...
A grid tied photovoltaic (PV) power conversion topology is presented in this study with a novel scheme of resynchronization to the grid. This scheme serves the purpose of supplying continuous power to the load along with feeding power to the grid. The control approach helps in mitigation of harmonics and improving the power quality while extracting the optimum power from the PV array. Depending on the availability of grid voltage, the proposed configuration is controlled using three approaches, defined as grid current control, Point of Common Coupling (PCC) voltage control and intentional islanding with re-synchronisation. A simple proportional integral controller manages the grid current, load voltage, battery current and DC Direct Current (DC) link voltage within these modes. Moreover, a control scheme for quick and smooth transitions among the modes is described. The robustness of the system under erratic behaviour of solar insolation, load power and disturbances in grid supply makes it a suitable choice for a residential application. The control, design and simulation results are presented to demonstrate the satisfactory operation of the proposed system.
Three phase transformerless shunt active power filter with reduced switch cou...
Shunt active power filter is the preeminent solution against nonlinear loads, current harmonics and power quality problems. APF topologies for harmonic compensation use numerous high-power rating components and are therefore disadvantageous. Hybrid topologies combining low-power rating APF with passive filters are used to reduce the power rating of voltage source inverter. Hybrid APF topologies for high-power rating systems use a transformer with large numbers of passive components. In this paper, a novel four-switch two-leg VSI topology for a three-phase SAPF is proposed for reducing the system cost and size. The proposed topology comprises a two-arm bridge structure, four switches, coupling inductors, and sets of LC PFs. The third leg of the three-phase VSI is removed by eliminating the set of power switching devices, thereby directly connecting the phase with the negative terminals of the dc-link capacitor. The proposed topology enhances the harmonic compensation capability and provides complete reactive power compensation compared with conventional APF topologies. The new experimental prototype is tested in the laboratory to verify the results in terms of total harmonic distortion, balanced supply current, and harmonic compensation, following the IEEE-519 standard.
Control strategy for power flow management in a pv system supplying dc loads
The growing concern for energy saving has increased the usage of LED-based street lights, electronic chokes, compact fluorescent lamps, and inverter-fed drives. Hence, the load profile seen by the electrical grid is undergoing a notable change as these devices have to operate from a dc source. Photovoltaics (PV) being a major energy source, the aforementioned loads can be connected directly to the dc bus. A grid-connected PV system involves a power source (PV array), a power sink (load), and two power sources/sink (utility and battery), and hence, a power
flow management system is required to balance the power flow among these sources. One such system is developed for selecting the operating mode of the bidirectional converter by sensing the battery voltage. The viability of the scheme has been ascertained by performing experimental studies on a laboratory prototype. The control strategy is digitally implemented on an Altera Cyclone II Field Programmable Gate Array (FPGA) board, and the algorithm is verified for different modes of operation by varying the load. Experimental results are presented to bring out
the usefulness of the control strategy.
Power Quality Assessment of Voltage Positive Feedback Based Islanding Detecti...
Islanding refers to a condition where distributed generators (DGs) inject power solely to the local load after electrical separation from power grid. Several islanding detection methods (IDMs) categorized into remote, active, and passive groups have been reported to detect this undesirable state. In active techniques, a disturbance is injected into the DG’s controller to drift a local yardstick out of the permissible range. Although this disturbance leads to more effective detections even in well-balanced island, it raises the total harmonic distortion (THD) of the output current under the normal operation conditions. This paper analyzes the power quality aspect of the modified sliding mode controller as a new active IDM for grid-connected photovoltaic system (GCPVS) with a string inverter. Its performance is compared with the voltage positive feedback (VPF) method, a well-known active IDM. This evaluation is carried out for a 1 kWp GCPVS in MATLAB/Simulink platform by measuring the output current harmonics and THD as well as the efficiency under various penetration and disturbance levels. The output results demonstrate that since the proposed disturbance changes the amplitude of the output current, it does not generate harmonics/subharmonics. Thereby, it has a negligible adverse effect on power quality. It is finally concluded that the performance of the sliding mode-based IDM is reliable from the standpoints of islanding detection and power quality.
Design and Control of Wind integrated Shunt Active Power Filter to Improve Po...
In this paper wind energy conservation system (WECS) with shunt active power filter (SAPF) is proposed for harmonics elimination, power factor correction, reactive power compensation and grid current balancing. Adaptive neuro fuzzy inference system (ANFIS) based controller is implemented at WECS side to control the boost converter to achieve MPP and at SAPF sides to minimize voltage variations and enhance power quality. Here, synchronous reference frame (SRF) theory based reference current generation technique is employed in SAPF. The proposed scheme is implemented in MATLAB/Simulink. The results confirm that this method has better performance and can maintain total harmonic distortion (THD) level of the system within the IEEE standard 519.
A Unified Control and Power Management Scheme for PV-Battery-Based Hybrid Mic...
Battery storage is usually employed in Photovoltaic (PV) system to mitigate the power fluctuations due to the characteristics of PV panels and solar irradiance. Control schemes for PV-battery systems must be able to stabilize the bus voltages as well as to control the power flows flexibly. This paper proposes a comprehensive control and power management system (CAPMS) for PV-battery-based hybrid microgrids with both AC and DC buses, for both grid-connected and islanded modes. The proposed CAPMS is successful in regulating the DC and AC bus voltages and frequency stably, controlling the voltage and power of each unit flexibly, and balancing the power flows in the systems automatically under different operating circumstances, regardless of disturbances from switching operating modes, fluctuations of irradiance and temperature, and change of loads. Both simulation and experimental case studies are carried out to verify the performance of the proposed method.
A New Design Method of an LCL Filter Applied in Active DC-Traction Substations
This paper concentrates on the LCL filter with damping resistance intended to connect the shunt active power filter of an active DC-traction substation to the point of common coupling with the transmission grid. In order to find design conditions and conceive a design algorithm, attention is directed to the transfer functions related to currents and the associated frequency response. The mathematical foundation of the design method is based on the meeting the requirements related to the significant attenuation of the high-frequency switching current, concurrently with the unalterated flow of the current that needs to be compensated by active filtering. It is pointed out that there are practical limitations and a compromise must be made between the two requirements. To quantify the extent to which the harmonics to be compensated are influenced by imposing the magnitude response at both highest harmonic frequency to be compensated and switching frequency, a performance indicator is defined. As an additional design criterion, the damping power losses are taken into consideration. The validity and effectiveness of the proposed method are proved by simulation results and experimental tests on a laboratory test bench of small scale reproducing the specific conditions of a DC-traction substation with six-pulse diode rectifier.
Multifunctional grid tied pv system using modified klms control
This paper deals with the modified kernel least mean square (KLMS) control strategy in double-stage, solar photovoltaic (PV) grid tied system to enhance the power quality at common coupling point (CCP). This proposed control algorithm has less oscillations, fast convergence, fast dynamic response and good steady state performance. A control strategy is used to extract the fundamental active current component of load and generates reference grid current for a DC-AC converter. The proposed modified KLMS control mitigates multiple power quality concerns such as harmonics reduction, unity power factor and load balancing. The dynamic performance of proposed system is confirmed into the MATLAB\Simulink environment. Test results on hardware implementation are presented at varying solar irradiation levels and load unbalancing. Test results are found satisfactory and total harmonic distortion (THD) of the grid currents are observed well within the IEEE-519 standard.
An improved transformerless inverter for
Leading project maker in Nashik, Electrical project in nashik goelectromeh.in, Electronic project in nashik goelectromeh.in, computer project in nashik, Electrical project engineering project in nashik goelectromeh.in, Electronic project engineering project in nashik goelectromeh.in, Computer project engineering project in nashik goelectromeh.in,
Electrical project Diploma project in nashik goelectromeh.in, Electronic project Diploma project in nashik goelectromeh.in, Computer project Diploma project in nashik goelectromeh.in.
Maximum power extraction from wind energy system based on fuzzy logic control
This paper proposes a variable speed control scheme for grid-connected wind energy conversion system (WECS) using permanent magnet synchronous generator (PMSG). The control algorithm tracks the maximum power for wind speeds below rated speed of wind turbines and ensures the power will not go over the rated power for wind speeds over the rated value. The control algorithm employs fuzzy logic controller (FLC) to effectively do this target. The wind turbine is connected to the grid via back-to-back PWM-VSC. Two effective computer simulation packages (PSIM and Simulink) are used to carry out the simulation effectively. The control system has two controllers for generator side and grid side converters. The main function of the generator side controller is to track the maximum power through controlling the rotational speed of the wind turbine using FLC. In the grid side converter, active and reactive power control has been achieved by controlling q-axis and d-axis current components, respectively. The d-axis current is set at zero for unity power factor and the q-axis current is controlled to deliver the power flowing from the dc-link to the electric utility grid.
What's hot (20)
A three phase grid tied spv system with adaptive dc link voltage for cpi volt...
A three phase grid tied spv system with adaptive dc link voltage for cpi volt...
Power quality improvement in distribution network using DSTATCOM with battery...
Power quality improvement in distribution network using DSTATCOM with battery...
A novel online fuzzy control method of static var compensation for an effecti...
A novel online fuzzy control method of static var compensation for an effecti...
Improving the Dynamic Performance of Wind Farms with STATCOM
Improving the Dynamic Performance of Wind Farms with STATCOM
Power Quality Improvement of Grid-Connected Photovoltaic Systems Using Trans-...
Power Quality Improvement of Grid-Connected Photovoltaic Systems Using Trans-...
Statcom for improved dynamic performance of wind farms in power grid
Statcom for improved dynamic performance of wind farms in power grid
Power Quality Improvement in Solar Fed Cascaded Multilevel Inverter with Outp...
Power Quality Improvement in Solar Fed Cascaded Multilevel Inverter with Outp...
An integrated boost resonant converter for photovoltaic applications
An integrated boost resonant converter for photovoltaic applications
Designing of multilevel dpfc to improve power quality
Designing of multilevel dpfc to improve power quality
Irradiance-adaptive PV Module Integrated Converter for High Efficiency and Po...
Irradiance-adaptive PV Module Integrated Converter for High Efficiency and Po...
Single-phase solar PV system with battery and exchange of power in grid-conne...
Single-phase solar PV system with battery and exchange of power in grid-conne...
Three phase transformerless shunt active power filter with reduced switch cou...
Three phase transformerless shunt active power filter with reduced switch cou...
Control strategy for power flow management in a pv system supplying dc loads
Control strategy for power flow management in a pv system supplying dc loads
Power Quality Assessment of Voltage Positive Feedback Based Islanding Detecti...
Power Quality Assessment of Voltage Positive Feedback Based Islanding Detecti...
Design and Control of Wind integrated Shunt Active Power Filter to Improve Po...
Design and Control of Wind integrated Shunt Active Power Filter to Improve Po...
A Unified Control and Power Management Scheme for PV-Battery-Based Hybrid Mic...
A Unified Control and Power Management Scheme for PV-Battery-Based Hybrid Mic...
A New Design Method of an LCL Filter Applied in Active DC-Traction Substations
A New Design Method of an LCL Filter Applied in Active DC-Traction Substations
Multifunctional grid tied pv system using modified klms control
Multifunctional grid tied pv system using modified klms control
Maximum power extraction from wind energy system based on fuzzy logic control
Maximum power extraction from wind energy system based on fuzzy logic control
Similar to Single-Phase Grid-tied Transformerless Inverter of Zero Leakage Current for PV System
Front end buck rectifier with reduced filter size and single-loop control
This paper presents a transformerless solution for front-end rectification, which is particularly suitable for traction applications, requiring high voltages to be stepped down to appropriate dc voltage. The proposed topology is based on pulse widthmodulation buck rectifier (current source inverter topology) and is capable of rectification and stepping down of single-phase ac supply, in a single stage. A new control scheme is proposed to achieve constant dc output voltage and sinusoidal source current, irrespective of large ripples in the dc inductor current. The proposed scheme is configured in single-loop voltage control mode. The relevant small-signal model is derived from the large-signal model using multi order decomposition. An elaborate procedure of dc filter design is discussed, for circuit operation with minimum energy storage. All analytical results are validated by numerical simulation for sinusoidal and distorted source voltage. Experimental verification is achieved through a 1.2-kW grid-connected laboratory prototype.
Performance enhancement of shunt active power filter with fuzzy and hysteresi...
This paper proposes fuzzy and hysteresis controllers based three phase Shunt Active Power Filter
for current harmonic compensation to improve the performance of 3ɸ supply system feeding
non- linear loads. The Shunt Active Power Filter is used to eliminate current harmonics. The dc
link control strategy is based on the fuzzy logic controller. Gating pulses for the Shunt Active
Filter is generated using Hysteresis current controller based Pulse width modulation technique.
The proposed model is simulated in MATLAB/SIMULINK. Simulation results show that the
dynamic behavior is better than the conventional Proportional- Integral (PI) controller and is
found to be more robust for changes in load.
Power Quality Analysis and Enhancement of Grid Connected Solar Energy System
In recent years, renewable energy resources are utilized to meet the growing energy demand. The integration of renewable energy resources with the grid incorporates power electronic converters for conversion of energy. These power electronic converters introduce power quality issues such as a harmonics, voltage regulation etc. Hence, to improve the power quality issues, this work proposes a new control strategy for a grid interconnected solar system. In this proposed work, a maximum power point tracking (MPPT) scheme has been used to obtain maximum power from the solar system and DC/DC converter is implemented to maintain a constant DC voltage. An active filtering method is utilized to improve the power quality of the grid connected solar system. The proposed system is validated through dynamic simulation using MATLAB/Simulink Power system toolbox and results are delivered to validate the effectiveness of the work.
IRJET- A Review on Solar based Multilevel Inverter with Three Phase Grid Supply
https://www.irjet.net/archives/V6/i3/IRJET-V6I3422.pdf
power management strategies for a grid-connected PV-FC Hybrid system
This paper presents a method to operate a grid connected hybrid system. The hybrid system composed of a Photovoltaic (PV) array and a Proton exchange membrane fuel cell (PEMFC) is considered. The PV array normally uses a maximum power point tracking (MPPT) technique to continuously deliver the highest power to the load when variations in irradiation and temperature occur, which make it become an uncontrollable source. In coordination with PEMFC, the hybrid system output power becomes controllable. Two operation modes, the unit-power control (UPC) mode and the feeder-flow control (FFC) mode, can be applied to the hybrid system. The coordination of two control modes, the coordination of the PV array and the PEMFC in the hybrid system, and the determination of reference parameters are presented. The proposed operating strategy with a flexible operation mode change always operates the PV array at maximum output power and the PEMFC in its high efficiency performance band, thus improving the performance of system operation, enhancing system stability, and decreasing the number of operating mode changes.
New ac dc power factor correction architecture suitable for high frequency op...
This paper presents a novel ac-dc power factor correction (PFC) power conversion architecture for single-phase grid interface. The proposed architecture has significant advantages for achieving high efficiency, good power factor, and converter miniaturization, especially in low-to-medium power applications. The architecture enables twice-line-frequency energy to be buffered at high voltage with a large voltage swing, enabling reduction in the energy buffer capacitor size, and elimination of electrolytic capacitors. While this architecture can be beneficial with a variety of converter topologies, it is especially suited for system miniaturization by enabling designs that operate at high frequency (HF, 3 – 30 MHz). Moreover, we introduce circuit implementations that provide efficient operation in this range. The proposed approach is demonstrated for an LED driver converter operating at a (variable) HF switching frequency (3 – 10 MHz) from 120Vac, and supplying a 35Vdc output at up to 30W. The prototype converter achieves high efficiency (92 %) and power factor (0.89), and maintains good performance over a wide load range. Owing to architecture and HF operation, the prototype achieves a high ‘box’ power density of 50W/ in3 (‘displacement’ power density of 130W/ in3), with miniaturized inductors, ceramic energy buffer capacitors, and a small-volume EMI filter.
A low voltage ride-through strategy using mixed potential function for three-...
This paper presents a new control strategy for low-voltage ride-through for 3-phase grid-connected photovoltaic systems. The proposed fault ride through control algorithm, which is designed based on mixed potential function, can protect the inverter from over current failure under both symmetric and asymmetric faults, reduce the double frequency oscillation and provides reactive power support by applying a voltage compensation unit. With the proposed method, the inverter can also inject sinusoidal current during asymmetric faults. The method does not require a hard switch to switch from the Maximum Power Point Tracking (MPPT) to a non-MPPT algorithm, which ensures a smooth transition.
Simulation and analysis of perturb and observe mppt algorithm for array using...
This paper presents the comparative analysis between constant duty cycle and Perturb & Observe (P&O) algorithm for extracting the power from Photovoltaic Array (PVA). Because of nonlinear characteristics of PV cell, the maximum power can be extract under particular voltage condition. Therefore, Maximum Power Point Tracking (MPPT) algorithms are used in PVA to maximize the output power. In this paper the MPPT algorithm is implemented using Ćuk converter. The dynamics of PVA is simulated at different solar irradiance and cell temperature. The P&O MPPT technique is a direct control method enables ease to implement and less complexity.
Single-Stage Switched-Capacitor Module (S3CM) Topology for Cascaded Multileve...
A two-stage switched-capacitor based multilevel inverter possesses a drawback such that switches in the second stage (i.e. H-bridge) endure higher voltage stress. To resolve this problem, this letter proposes a single-stage switched-capacitor module (S3CM) topology for cascaded multilevel inverter which ensures the peak inverse voltage across all switches within the dc source voltage. Nine voltage levels can be generated with only one dc source and two incorporated capacitors. Hence, the number of isolated dc sources are significantly reduced compared to cascaded H-bridge. In addition, voltage boosting gain of two is achieved. A comparative analysis against the recent topology reveals that the proposed S3CM topology achieves switch count reduction. The operation of the proposed topology is validated through circuit analysis followed by experimental results of a single module (9-level) prototype.
Sensorless bldc motor commutation point detection and phase deviation correct...
Phase-to-neutral voltage or neutral-to-virtual neutral voltage zero-crossing points (ZCPs) detection method is usually used for sensorless BLDC motor commutation control. Unfortunately, neither of them can be realized in lower speed range. In this paper, a simple commutation point detection method is proposed based on detecting inactive phase terminal to dc-link midpoint voltage. It eliminates the requirement of neutral wire or virtual neutral voltage and provides an amplified version of back electromotive force (EMF) at the ZCPs which makes the lower speed range detection possible. As the speed increasing, commutation point error is enlarged due to the low pass filter (LPF) et al. Utilizing the symmetry of the terminal to midpoint voltage the phase error can be corrected. However, due to the nonlinear relationship between the detected voltage difference and phase error, it is difficult to regulate the error fast and robustly. Therefore, a novel phase regulator based on fuzzy neural network (FNN) is proposed in this paper with simple structure and learning ability. The validity of the proposed ZCPs detection method and commutation instant shift correction method are verified through experimental results.
Mppt with single dc–dc converter and inverter for grid connected hybrid wind-...
A new topology of a hybrid distributed generator based on photovoltaic and wind-driven permanent magnet synchronous generator is proposed. In this generator, the sources are connected together to the grid with the help of only a single boost converter followed by an inverter. Thus, compared to earlier schemes, the proposed scheme has fewer power converters. A model of the proposed scheme in the d − q-axis reference frame is developed. Two low-cost controllers are also proposed for the new hybrid scheme to separately trigger the dc–dc converter and the inverter for tracking the maximum power from both sources. The integrated operations of both proposed controllers for different conditions are demonstrated through simulation and experimentation. The steady-state performance of the system and the transient response of the controllers are also presented to demonstrate the successful operation of the new hybrid system. Comparisons of experimental and simulation results are given to validate the simulation model.
A Highly Efficient and Reliable Inverter Configuration Based Cascaded Multi-L...
This paper presents an improved Cascaded Multi-Level Inverter (CMLI) based on a highly efficient and reliable configuration for the minimization of the leakage current. Apart from a reduced switch count, the proposed scheme has additional features of low switching and conduction losses. The proposed topology with the given PWM technique reduces the high-frequency voltage transitions in the terminal and common-mode voltages. Avoiding high-frequency voltage transitions achieves the minimization of the leakage current and reduction in the size of EMI filters. Furthermore, the extension of the proposed CMLI along with the PWM technique for 2m+1 levels is also presented, where m represents the number of Photo Voltaic (PV) sources. The proposed PWM technique requires only a single carrier wave for all 2m+1 levels of operation. The Total Harmonic Distortion (THD) of the grid current for the proposed CMLI meets the requirements of IEEE 1547 standard. A comparison of the proposed CMLI with the existing PV Multi-Level Inverter (MLI) topologies is also presented in the paper. Complete details of the analysis of PV terminal and common-mode voltages of the proposed CMLI using switching function concept, simulations, and experimental results are presented in the paper.
Simulation of distributed power flow controller for voltage sag compensation
In this paper, we introduced a new series-shunt type FACTS controller called as distributed power flow controller to improve and maintain the power quality of an electrical power system. This DPFC method is same as the UPFC used to compensate the voltage sag and the current swell these are voltage based power quality problems. As compared to UPFC the common dc link capacitor is removed and three individual single phase converters are used instead of a three phase series converter. Series referral voltages, branch currents are used in this paper for designing control circuit. The evaluated values are obtained by using MATLAB/SIMULINK.
Simulation of distributed power flow controller for voltage sag compensation
In this paper, we introduced a new series-shunt type FACTS controller called as distributed power flow controller to improve and maintain the power quality of an electrical power system. This DPFC method is same as the UPFC used to compensate the voltage sag and the current swell these are voltage based power quality problems. As compared to UPFC the common dc link capacitor is removed and three individual single phase converters are used instead of a three phase series converter. Series referral voltages, branch currents are used in this paper for designing control circuit. The evaluated values are obtained by using MATLAB/SIMULINK.
Performance enhancement of actively controlled hybrid dc microgrid incorporat...
In this paper, a new energy control scheme is proposed for actively controlled hybrid dc microgrid to reduce the adverse impact of pulsed power loads. The proposed energy control is an adaptive current-voltage control (ACVC) scheme based on the moving average measurement technique and an adaptive proportional compensator. Unlike conventional energy control methods, the proposed ACVC approach has the advantage of controlling both voltage and current of the system while keeping the output current of the power converter at a relatively constant value. For this study, a laboratory scale hybrid dc microgrid is developed to evaluate the performance of the ACVC strategy and to compare its performance with the other conventional energy control methods. Using experimental test results, it is shown that the proposed strategy highly improves the dynamic performance of the hybrid dc microgrid. Although the ACVC technique causes slightly more bus voltage variation, it effectively eliminates the high current and power pulsation of the power converters. The experimental test results for different pulse duty ratios demonstrated a significant improvement achieved by the developed ACVC scheme in enhancing the system efficiency, reducing the ac grid voltage drop and the frequency fluctuations.
Three phase unidirectional rectifiers with open-end source and cascaded float...
This paper presents two topologies of three-phase semicontrolled rectifiers suitable for open-end ac power sources. The rectifiers are composed by a combination of two-level three phase bridges (controlled, semicontrolled or uncontrolled), and three single-phase floating capacitor h-bridges (controlled). These topologies generate two powered dc-links, each one belonging to a three-phase bridge. They present a reduced number of controlled power switches if compared to other open-end configurations of similar complexity found in the literature. It is also proposed a space-vector pulse width modulation (SV-PWM) approach and a method of floating capacitor voltage control dedicated to the topologies, with an equivalent approach based on the level-shifted PWM (LS-PWM). The proposed SV-PWM solving method is based on a redundant state selection (RSS) technique, which allows the floating capacitors voltage regulation. On the other hand, the LS-PWM solving method is based on the neutral voltage selection, which is shown to be equivalent to the SVPWM RSS technique seen from the control system. Simulation results are shown to validate proposed topologies, as well as the SV-PWM and LS-PWM techniques, and the control strategy. Experimental results are shown to demonstrate proposed configurations feasibility.
Single phase grid connected photovoltaic inverter
This article proposes a topology for single-phase two stage grid connected solar photovoltaic (PV) inverter for residential applications. Our proposed grid-connected power converter consists of a switch mode DC-DC boost converter and a H-bridge inverter. The switching strategy of proposed inverter consists with a combination of sinusoidal pulse width modulation (SPWM) and square wave along with grid synchronization condition. The performance of the proposed inverter is simulated under grid-connected scenario via PSIM. Furthermore, the intelligent PV module system is implemented using a simple maximum power point tracking (MPPT) method utilizing power balance is also employed in order to increase the systems efficiency.
A Sensorless Power Reserve Control Strategy for Two-Stage Grid-Connected PV S...
Due to the still increasing penetration of grid connected Photovoltaic (PV) systems, advanced active power control functionalities have been introduced in grid regulations. A power reserve control, where namely the active power from the PV panels is reserved during operation, is required for grid support. In this paper, a cost-effective solution to realize the power reserve for two-stage grid-connected PV systems is proposed. The proposed solution routinely employs a Maximum Power Point Tracking (MPPT) control to estimate the available PV power and a Constant Power Generation (CPG) control to achieve the power reserve. In this method, the solar irradiance and temperature measurements that have been used in conventional power reserve control schemes to estimate the available PV power are not required, and thereby being a sensorless approach with reduced cost. Experimental tests have been performed on a 3-kW two-stage single-phase grid-connected PV system, where the power reserve control is achieved upon demands.
IRJET- Energy Management and Control for Grid Connected Hybrid Energy Storage...
https://www.irjet.net/archives/V6/i3/IRJET-V6I3788.pdf
Similar to Single-Phase Grid-tied Transformerless Inverter of Zero Leakage Current for PV System (20)
Front end buck rectifier with reduced filter size and single-loop control
Front end buck rectifier with reduced filter size and single-loop control
Performance enhancement of shunt active power filter with fuzzy and hysteresi...
Performance enhancement of shunt active power filter with fuzzy and hysteresi...
Power Quality Analysis and Enhancement of Grid Connected Solar Energy System
Power Quality Analysis and Enhancement of Grid Connected Solar Energy System
IRJET- A Review on Solar based Multilevel Inverter with Three Phase Grid Supply
IRJET- A Review on Solar based Multilevel Inverter with Three Phase Grid Supply
power management strategies for a grid-connected PV-FC Hybrid system
power management strategies for a grid-connected PV-FC Hybrid system
New ac dc power factor correction architecture suitable for high frequency op...
New ac dc power factor correction architecture suitable for high frequency op...
A low voltage ride-through strategy using mixed potential function for three-...
A low voltage ride-through strategy using mixed potential function for three-...
Simulation and analysis of perturb and observe mppt algorithm for array using...
Simulation and analysis of perturb and observe mppt algorithm for array using...
Single-Stage Switched-Capacitor Module (S3CM) Topology for Cascaded Multileve...
Single-Stage Switched-Capacitor Module (S3CM) Topology for Cascaded Multileve...
Sensorless bldc motor commutation point detection and phase deviation correct...
Sensorless bldc motor commutation point detection and phase deviation correct...
Mppt with single dc–dc converter and inverter for grid connected hybrid wind-...
Mppt with single dc–dc converter and inverter for grid connected hybrid wind-...
A Highly Efficient and Reliable Inverter Configuration Based Cascaded Multi-L...
A Highly Efficient and Reliable Inverter Configuration Based Cascaded Multi-L...
Simulation of distributed power flow controller for voltage sag compensation
Simulation of distributed power flow controller for voltage sag compensation
Simulation of distributed power flow controller for voltage sag compensation
Simulation of distributed power flow controller for voltage sag compensation
Performance enhancement of actively controlled hybrid dc microgrid incorporat...
Performance enhancement of actively controlled hybrid dc microgrid incorporat...
Three phase unidirectional rectifiers with open-end source and cascaded float...
Three phase unidirectional rectifiers with open-end source and cascaded float...
A Sensorless Power Reserve Control Strategy for Two-Stage Grid-Connected PV S...
A Sensorless Power Reserve Control Strategy for Two-Stage Grid-Connected PV S...
IRJET- Energy Management and Control for Grid Connected Hybrid Energy Storage...
IRJET- Energy Management and Control for Grid Connected Hybrid Energy Storage...
More from Asoka Technologies
Solar pv charging station for electric vehicles
Of late, electric vehicles (EVs) have attracted much attention owing to their use of clean energy. Large progress in lithium-ion battery has propelled the development of EVs.However, the challenge is that growing number of EVs leads to huge demand in electric power, which will aggravate the power grid load. This leads to an exploration for alternative and clean sources of energy to charge EVs. This project implements solar energy system to erect a charging station for EV application. The charging station employs multi-port charging by providing a constant voltage DC bus. The charging controllers are operated based on the concept of power balance, and constant current/constant voltage charging. Performance of the charging system is validated with simulation and experimental results.
Generation of Higher Number of Voltage Levels by Stacking Inverters of Lower ...
This paper proposes a new method of generating higher number of levels in the voltage waveform by stacking multilevel converters with lower voltage space vector structures. An important feature of this stacked structure is the use of low voltage devices while attaining higher number of levels. This will find extensive applications in electric vehicles since direct battery drive is possible. The voltages of all the capacitors in the structure can be controlled within a switching cycle using the switching state redundancies (pole voltage redundancies). This helps in reducing the capacitor size. Also, the capacitor voltages can be balanced irrespective of modulation index and load power factor. To verify the concept experimentally, a 9-level inverter is developed by stacking two 5-level inverters and an induction motor is run using V/f control scheme. Both steady state and transient results are presented.
Novel symmetric modular hybrid multilevel inverter with reduced number of sem...
In this paper, by using a modular hybrid structure, a new topology for symmetric multilevel inverters (MLI) with a small number of semiconductors and low voltage stress across switches is proposed. Despite many other topologies, this topology can inherently produce negative levels and zero levels without using the H-bridge. The voltage stress across a particular switch of the proposed MLI is inversely proportional to the number of the switching of that switch in a voltage period. The proposed structure is based on two types of module, that is, the f-module and the e-module. The e-module uses a capacitive voltage divider to double the number of non-zero levels. The voltages of the capacitors are approximately balanced without complex control methods. The basic structure of the proposed topology is formed by connecting the f-module and the e-module in series with each other, and the cascaded topology is developed by cascading multiple f-modules with an e-module. To investigate the proposed topology and proving its practicability, simulation results with MATLAB/Simulink, investigation of the capacitor voltages, loss calculations and experimental results are presented. A comparative study is also performed to show the merit of the new multilevel inverter over other topologies.
A Variable DC Link based Novel Multilevel Inverter Topology for Low Voltage A...
In this paper; a variable dc link based novel multilevel inverter (MLI) topology is proposed. This proposed topology comprises two variable dc links and a modified H-bridge unit. This new single-phase topology offers advantages such as reduction in count of switches; gate drivers and dc sources while simultaneously improving the power quality. The proposed topology has been analyzed for both symmetric and asymmetric modes of operation. A comparative study of the proposed topology with some recent MLI topologies has been presented. The comparative study indicates that the proposed topology requires less number of dc sources; switches and driver circuits as compared to other topologies. The proposed topology has been simulated for 31- level asymmetric configuration in MATLAB/SIMULINK environment to verify the proper operation of proposed topology. Harmonic analysis was also performed for 31-level inverter which showed significant reduction in the total harmonic distortion (THD) for phase voltage and current waveforms. The proposed topology is suitable for low voltage applications such as standalone photovoltaic (PV) systems and hybrid electric vehicles (HEVs).
A Simplified Space Vector Pulse-Width Modulation Scheme for Three-Phase Casca...
A simplified space vector pulse-width modulation (SVPWM) for three-phase cascaded H-bridge (CHB) inverters is presented in this paper. Treating each unit as a three-level inverter and adopting serial calculation mode, a CHB inverter is modulated unit by unit using three-level SVPWM. Duty cycles of real sector are obtained by mapping duty cycles of sector 1, in which the calculation of three-level SVPWM is done. The process to implement multilevel SVPWM is simplified to the process to implement three-level SVPWM. By reusing FPGA chip resource which is used for the calculation of three-level SVPWM, the presented SVPWM can be easily adopted to a CHB inverter with different number of units, while the FPGA chip resource utilization is reduced significantly. In addition, the presented SVPWM provides an effective switching frequency higher than the switching frequency of IGBTs. Simulation and experimental results are provided to verify the feasibility of the presented SVPWM.
A New Family of Step-up Hybrid Switched- Capacitor Integrated Multilevel Inve...
In the low voltage based renewable systems like PV and Fuel cell applications, the step-up of the output voltage to drive the loads is essential. For this, the integration of switched-capacitor (SC) units with the dc-ac converters will have the potential advantages like improved efficiency, optimal switching devices, small size of passive elements (L and C) as compared with traditional two-stage conversion system (dc/dc converter and dc/ac converter). This paper focuses on a new family of step-up multilevel inverter topologies with switched capacitor integration with dual input voltage sources. With the flexibility of 2 dc sources and switching capacitor circuits, four different topologies have been suggested in this paper with features of high voltage gain, reduced component count, reduced voltage stress and self-voltage balancing of the capacitor while achieving a higher number of levels. A detailed analysis of proposed multilevel inverters has been analyzed with the symmetrical and asymmetrical mode of operations and the associated gain, the number of levels, and other performance indices are presented. An in-depth study of all the topologies has been accomplished in this paper with several comparative studies in terms of components count, voltage gain and cost. The effectiveness and practicability of the suggested topology with 13 level output voltage has been explained by the experimental results obtained from a scale down prototype.
A multi cell 21-level hybrid multilevel inverter synthesizes a reduced number...
A multi-cell hybrid 21-Level multilevel inverter is proposed in this paper. The proposed topology includes two-unit; an H-bridge is cascaded with a modified K-type unit to generate an output voltage waveform with 21 levels based only on two unequal DC suppliers. The proposed topology's advantage lies in the fine and clear output voltage waveforms with high output efficiency. Meanwhile, the high number of output voltage waveform levels generates a low level of distortion and reduces the level of an electromagnetic interface (EMI). Moreover, it reduces the voltage stress on the switching devices and gives it a long lifetime. Also, the reduction in the number of components has a noticeable role in saving size and cost. Regarding the capacitors charging, the proposed topology presents an online method for charging and balancing the capacitor's voltage without any auxiliary circuits. The proposed topology can upgrade to a high number of output steps through the cascading connection. Undoubtedly this cascading will increase the power level to medium and high levels and reduce the harmonics content to a neglectable rate. The proposed system has been tested through the simulation results, and an experimental prototype based on the controller dSPACE (DS-1103) hardware unit used to support the simulation results.
A generalized multilevel inverter topology with reduction of total standing v...
This paper presents a new multilevel inverter topology with reduced active switches and total standing voltage. The proposed topology can generate a high number of voltage levels in the symmetric configuration. This topology intuitively generates positive and negative cycles without an additional H-bridge unit, which considerably reduces the total standing voltage of the inverter. A cascaded structure is developed from the proposed topology to create higher voltage levels. To show the novelty of the proposed topology, a thorough comparison between the available and the proposed topologies in terms of the number of switches, standing voltages, and dc-sources is presented. Furthermore, the power loss analysis is carried out for various load values. The feasibility of the proposed nine-level inverter is verified with simulation and experimental results.
Residential Community Load Management based on Optimal Design of Standalone H...
Microgrids being an important entity in the distribution system, and to get their full advantages
by incorporating maximum distributed generation, standalone hybrid renewable energy systems (HRESs), being environmentally-safe and economically-efficient, are considered as the promising solution to electrify remote areas where the grid power is not available. In this work, a techno-economic investigation with an optimal design of HRES is presented to fulfill the domestic electricity need for a residential area of the Sherani district in the Province of Baluchistan, Pakistan. Nine case studies based on PV/wind/diesel/battery are analyzed based on net present cost (NPC), cost of energy (COE), and emission to decide the feasible solution. HOMER tool is utilized to accomplish modeling and simulation for economic analysis and optimal sizing. Simulation results demonstrated that HRES with PV-wind-battery is the most viable option for the specified area, and the optimal sizing of components are also obtained with $ 28,620 NPC and 0.311 $/kWh COE which shows 81.65% reduction in cost and 100% preserving in toxic emission while fulfilling 100% energy demand with 67.3% of excess energy. Furthermore, MATLAB/Simulink modeling for the optimally designed system is built for technical analysis while its effectiveness is proved by keeping dc and ac buses voltage constant, safe operating range of battery state of charge (SOC) with active power balance between HRES components, as well as efficient ac voltage quality, regardless of generation disturbances and load fluctuations. The output signal has total harmonic distortion (THD) of 0.30% as compared to 5.44% with the conventional control scheme. The novelty lies in the sequential application of both HOMER and MATLAB simulations of the proposed HRES model and validation of the proposition for the studied area; by using and implementing model predictive control (MPC) of a reconfigurable inverter.
Reliability evaluation of MPPT based interleaved boost converter for PV system
The demand for power supply and depletion of the conventional energy sources are increasing drastically. So to overcome this problem, the best alternative power generation for conventional fossil fuel is Photovoltaic solar cell based system because of its advantage of pollution free and its availability in abundance with free of cost. In the MPPT based PV system the converters are the most sensitive part. Therefore to provide uninterrupted power supply without compromising the quality of power, reliability evaluation of interleaved boost converter becomes necessary. MATLAB/Simulink is used for the simulation studies and to determine the power losses of various components of the converter which is used in calculating the failure rates and reliability of the interleaved boost converter. Reliability studies of IBC have not been studied much. However there exists few literature in which reliability expression has been developed using Markov technique which is a more complex method as compare to Reliability Block Diagram (RBD). Therefore this paper proposes reliability modeling and reliability evaluation of Interleaved boost converter in MPPT based photo-voltaic system by using simple RBD method.
Power optimisation scheme of induction motor using FLC for electric vehicle
In electric vehicles (EVs) and hybrid EVs, energy efficiency is essential where the energy storage is limited. Adding to its high stability and low cost, the induction motor efficiency improves with loss minimisation. Also, it can consume more power than the actual need to perform its working when it is operating in less than full load condition. This study proposes a control strategy based on the fuzzy logic control (FLC) for EV applications. FLC controller can improve the starting current amplitude and saves more power. Through the MATLAB/SIMULINK software package, the performance of this control was verified through simulation. As compared with the conventional proportional integral derivative controller, the simulation schemes show good, high-performance results in time-domain response and rapid rejection of system-affected disturbance. Therefore, the core losses of the induction motor are greatly reduced, and in this way improves the efficiency of the driving system. Finally, the suggested control system is validated by the experimental results obtained in the authors’ laboratory, which are in good agreement with the simulation results.
Power Flow Control of Interconnected AC-DC Microgrids in Grid-Connected Hybri...
This paper introduces a new approach for power flow control of interconnected AC-DC microgrids in grid-connected hybrid microgrids based on implementing a modified unified interphase power controller (UIPC). A typical grid-connected hybrid microgrid including one AC microgrid and one DC microgrid is considered as studied system. Instead of using the parallel-connected power converters, these microgrids are interconnected using a modified UIPC. As the first contribution of this paper, the conventional structure of UIPC, which uses three power converters in each phase, is modified so that a reduced number of power converters is implemented for power exchange control between AC-DC microgrids. The modified structure includes one power converter in each phase, named as line power converter (LPC), and a power converter which regulates the DC bus voltage, named as bus power converter (BPC) here. The AC microgrid is connected to the main grid through the LPCs which their DC buses are linked and can operate in capacitance mode (CM) or inductance mode (IM). A fuzzy logic controller is used in the control structure of the LPCs. The fuzzy inference system is optimized based on H∞ filtering method to reduce the errors in membership functions design. Through the BPC, the DC voltage of LPCs is supplied by the DC microgrid. However, since the DC microgrid voltage is provided here by a PV system, the DC link voltage of the LPCs is fluctuating. Thus, as the second contribution, to stabilize the DC link fluctuations, a new nonlinear disturbance observer based robust multiple-surface sliding mode control (NDO-MS-SMC) strategy is presented for DC side control of the BPC. The simulation results confirm the effectiveness of the proposed power flow control strategy of the improved UIPC for hybrid microgrids.
Power flow control of hybrid micro grids using modified uipc
Neuro Fuzzy Inference System (ANFIS) controlled modified Unified Inter-Phase Power Controller (UIPC). For study, a classic hybrid micro-grid connected to grid comprising of a AC micro-grid and a DC micro-grid is taken into account. These micro-grids are interconnected employing a modified UIPC, rather than using the power converters connected in parallel. As the first input of this paper is the standard structure of UIPC, which used three power converters in every phase. It was then modified such as number of power converters is used less and implemented for the control of the exchange of power between AC-DC microgrids. In every phase there is one power electronic converter in the improved structure. It is called as Line Power Converter (LPC). Also there is Bus Power Converter (BPC) to regulate the voltage of the DC bus. The Line Power Converters links the AC micro-grid to the main grid. The DC buses are also linked with them. It can be operated in Inductance Mode (IM) as well as Capacitance Mode (CM). The control structure of LPCs has an Adaptive Fuzzy Logic Controller in it. For hybrid micro-grids, the capability of the suggested power flow control strategy is confirmed by the MATLAB simulation results.
Modelling and voltage control of the solar wind hybrid micro-grid with optimi...
Electricity generation from the wind and solar photovoltaic (PV) systems are highly dependent upon weather conditions. Their intermittent nature leads to fluctuations in their output. Therefore, the need for rapid compensation for energy transmission and distribution systems is increasingly important. Static Synchronous Compensator (STATCOM) can be adopted for reactive power compensation and for decreasing the voltage fluctuation caused by the system and renewable energy sources. This study presents modelling of a Solar PV-Wind Hybrid Micro-grid and the increase of the stable operating limit of the system in case of the incorporation of STATCOM is examined. The major contribution of this paper is the optimization of gain parameters of four PI controllers in STATCOM control circuit based on genetic algorithms (GA) and Bacteria Foraging Algorithm (BFA) and therefore obtaining better responses and voltage stability in terms of nonlinear nature of solar-wind hybrid micro-grid. The Simulink models of the system architecture include a wind turbine model, a solar PV power system model and a STATCOM. It is certified that the voltage fluctuation at the end of the bus bar is reduced by 8% using conventional PI controller, by 10% for GA-based PI controller, and by 15% for BFA based PI controller under variable load. The results obtained by GA and BFA-based optimization of PI controllers are compared with that of the conventional controller and better results attained.
Intelligent Power Sharing of DC Isolated Microgrid Based on Fuzzy Sliding Mod...
Linear droop control can realize power sharing among generators in DC microgrid without relying on critical communication links. However, the droop relationship between output power and voltage magnitude of renewable power generate system is nonlinear with uncertainties and disturbances from renewable sources and loads in practical DC microgrid. A novel droop scheme is proposed for an isolated DC microgrid to solve the nonlinear problem. The control strategy is proposed by using the Takagi-Sugeno (T-S) fuzzy model and sliding mode algorithm. The nonlinear droop characteristics can be represented by T-S model through taking advantage of locally measured output variables. The sliding mode droop controller is designed for compensating the uncertainties and disturbances to derive accurate power sharing based on T-S fuzzy model. The proposed scheme is proved to be effective under variable operating conditions through PSIM/Matlab simulation.
Implementation of solar pv battery and diesel generator based electric vehic...
In this paper, a solar PV (Photovoltaic) array, a battery energy storage (BES), a diesel generator (DG) set and grid based EV charging station (CS) is utilized to provide the incessant charging in islanded, grid connected and DG set connected modes. The charging station is primarily designed to use the solar photovoltaic PV array and a BES to charge the electric vehicle (EV) battery. However, in case of exhausted storage battery and unavailable solar PV array generation, the charging station intelligently takes power from the grid or DG (Diesel Generator) set. However, the power from DG set is drawn in a manner that, it always operates at 80-85% loading to achieve maximum fuel efficiency under all loading conditions. Moreover, in coordination with the storage battery, the charging station regulates the generator voltage and frequency without a mechanical speed governor. It also ensures that the power drawn from the grid or the DG set is at unity power factor (UPF) even at nonlinear loading. Moreover, the PCC (Point of Common Coupling) voltage is synchronized to the grid/ generator voltage to obtain the ceaseless charging. The charging station also performs the vehicle to grid active/reactive power transfer, vehicle to home and vehicle to vehicle power transfer for increasing the operational efficiency of the charging station. The operation of the charging station is experimentally validated using the prototype developed in the laboratory.
High step up quasi-z source dc-dc converter
In this paper, a high step-up Quasi-Z Source (QZS) DC-DC converter is proposed. This converter uses a hybrid switched-capacitors switched-inductor method in order to achieve high voltage gains. The proposed converter have resolved the voltage gain limitation of the basic QZS DC-DC converter while keeping its main advantages such as continuous input current and low voltage stress on capacitors. Compared to the basic converter, the duty cycle is not limited, and the voltage stress on the diodes and switch isn’t increased. In addition to these features, the proposed converter has a flexible structure, and extra stages could be added to it in order to achieve even higher voltage gains without increasing the voltage stress on devices or limiting the duty cycle. The operation principle of the converter and related relationships and waveforms are presented in the paper. Also, a comprehensive comparison between the proposed and other QZS based DC-DC converters is provided which confirms the superiority of the proposed converter. Simulations are done in PSCAD/EMTDC in order to investigate the MPPT capability of the converter. In addition, the valid performance and practicality of the converter are studied through the results obtained from the laboratory built prototype.
Fuel cell integrated unified power quality conditioner for voltage and curren...
Electrical and electronic devices when exposed to one or more power quality problems are prone to failure. This paper aims to enhance the quality of power in three-phase four-wire distribution grid using Fuel Cell Integrated Unified Power Quality Conditioner (FCI-UPQC). The proposed FCI-UPQC has four-leg converter on the shunt side and three-leg converter on the series side. A combination of a synchronous reference frame (SRF) and Instantaneous Reactive Power (IRP) theories are utilized to generate reference signals of the FCI-UPQC. Also, this paper proposes Adaptive Neuro-Fuzzy Inference System controller to maintain DC link voltage in the FCI-UPQC. The Adaptive Neuro-Fuzzy Inference System controller is designed like a sugeno fuzzy architecture and trained offline using data from the Proportional Integral (PI) controller. The obtained results proved that the proposed FCI-UPQC compensated power quality problems such as voltage sag, swell, harmonics, neutral current, source current imbalance in three-phase four-wire distribution grid. The presence of fuel cell in this work makes more effectiveness of the proposed system by providing real power support during supply interruption on the grid side.
Distributed incremental adaptive filter controlled grid interactive residenti...
In this paper, a distributed incremental adaptive filter (DIAF) controlled utility interfaced photovoltaic (PV) - battery microgrid system is presented with power quality features. From protection aspects, grid tied solar inverters are required to shut down at loss of the utility. However, the multi-purpose PV-battery system is developed to provide energy to the critical loads, even at loss of distribution network. The bidirectional controlled converter with a battery also mitigates the intermittency of a PV array under rapid variations in the weather. The extracted maximum power is supplied to the voltage source converter (VSC), which is transferred to the nonlinear loads and the utility. The distributed incremental adaptive filter is used to control the VSC with contribution of PV power and the battery. In addition, the DIAF control provides harmonics mitigation, load balancing and power factor improvement functionalities in order to deal with system connected with nonlinear loads. A PV power feed-forward (PVFF) term is incorporated in the current control for injection of active power to the utility as well as to improve the dynamic operation of residential PV-battery microgrid. The battery energy storage (BES) reduces the fuel bills and it is also utilized to provide smoothing attributes to the microgrid. The effectiveness of PV-battery microgrid is validated experimentally developed in the laboratory.
Application of Artificial Neural Networks for Shunt APF Control
Artificial Neural Network (ANN) is becoming an attractive estimation and regression technique in many control applications due to its parallel computing nature and high learning capability. There has been a lot of effort in employing the ANN in shunt active power filter (APF) control applications. Adaptive Linear Neuron (ADALINE) and feed-forward Multilayer Neural Network (MNN) are the most commonly used ANN techniques to extract fundamental and/or harmonic components present in the non-linear currents. This paper aims to provide an in-depth understanding on realizing ADALINE and feed-forward MNN based control algorithms for shunt APF. A step-by-step procedure to implement these ANN based techniques, in Matlab/ Simulink environment, is provided. Furthermore, a detailed analysis on the performance, limitation and advantages of both methods is presented in the paper. The study is supported by conducting both simulation and experimental validations.
More from Asoka Technologies (20)
Generation of Higher Number of Voltage Levels by Stacking Inverters of Lower ...
Generation of Higher Number of Voltage Levels by Stacking Inverters of Lower ...
Novel symmetric modular hybrid multilevel inverter with reduced number of sem...
Novel symmetric modular hybrid multilevel inverter with reduced number of sem...
A Variable DC Link based Novel Multilevel Inverter Topology for Low Voltage A...
A Variable DC Link based Novel Multilevel Inverter Topology for Low Voltage A...
A Simplified Space Vector Pulse-Width Modulation Scheme for Three-Phase Casca...
A Simplified Space Vector Pulse-Width Modulation Scheme for Three-Phase Casca...
A New Family of Step-up Hybrid Switched- Capacitor Integrated Multilevel Inve...
A New Family of Step-up Hybrid Switched- Capacitor Integrated Multilevel Inve...
A multi cell 21-level hybrid multilevel inverter synthesizes a reduced number...
A multi cell 21-level hybrid multilevel inverter synthesizes a reduced number...
A generalized multilevel inverter topology with reduction of total standing v...
A generalized multilevel inverter topology with reduction of total standing v...
Residential Community Load Management based on Optimal Design of Standalone H...
Residential Community Load Management based on Optimal Design of Standalone H...
Reliability evaluation of MPPT based interleaved boost converter for PV system
Reliability evaluation of MPPT based interleaved boost converter for PV system
Power optimisation scheme of induction motor using FLC for electric vehicle
Power optimisation scheme of induction motor using FLC for electric vehicle
Power Flow Control of Interconnected AC-DC Microgrids in Grid-Connected Hybri...
Power Flow Control of Interconnected AC-DC Microgrids in Grid-Connected Hybri...
Power flow control of hybrid micro grids using modified uipc
Power flow control of hybrid micro grids using modified uipc
Modelling and voltage control of the solar wind hybrid micro-grid with optimi...
Modelling and voltage control of the solar wind hybrid micro-grid with optimi...
Intelligent Power Sharing of DC Isolated Microgrid Based on Fuzzy Sliding Mod...
Intelligent Power Sharing of DC Isolated Microgrid Based on Fuzzy Sliding Mod...
Implementation of solar pv battery and diesel generator based electric vehic...
Implementation of solar pv battery and diesel generator based electric vehic...
Fuel cell integrated unified power quality conditioner for voltage and curren...
Fuel cell integrated unified power quality conditioner for voltage and curren...
Distributed incremental adaptive filter controlled grid interactive residenti...
Distributed incremental adaptive filter controlled grid interactive residenti...
Application of Artificial Neural Networks for Shunt APF Control
Application of Artificial Neural Networks for Shunt APF Control
Recently uploaded
Building Electrical System Design & Installation
Guide for Building Electrical System Design & Installation
Design and Analysis of Algorithms-DP,Backtracking,Graphs,B&B
Dynamic Programming
Backtracking
Techniques for Graphs
Branch and Bound
AKS UNIVERSITY Satna Final Year Project By OM Hardaha.pdf
AKS UNIVERSITY Satna Final Year Project By OM Hardaha.
Thank me later.
samsarthak31@gmail.com
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Recycled Concrete Aggregate in Construction Part III
Using recycled concrete aggregates (RCA) for pavements is crucial to achieving sustainability. Implementing RCA for new pavement can minimize carbon footprint, conserve natural resources, reduce harmful emissions, and lower life cycle costs. Compared to natural aggregate (NA), RCA pavement has fewer comprehensive studies and sustainability assessments.
一比一原版(IIT毕业证)伊利诺伊理工大学毕业证成绩单专业办理
IIT毕业证原版定制【微信：176555708】【伊利诺伊理工大学毕业证成绩单-学位证】【微信：176555708】（留信学历认证永久存档查询）采用学校原版纸张、特殊工艺完全按照原版一比一制作（包括：隐形水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠，文字图案浮雕，激光镭射，紫外荧光，温感，复印防伪）行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备，十五年致力于帮助留学生解决难题，业务范围有加拿大、英国、澳洲、韩国、美国、新加坡，新西兰等学历材料，包您满意。
◆◆◆◆◆ — — — — — — — — 【留学教育】留学归国服务中心 — — — — — -◆◆◆◆◆
【主营项目】
一.毕业证【微信：176555708】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【微信：176555708】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分→ 【关于价格问题（保证一手价格）
我们所定的价格是非常合理的，而且我们现在做得单子大多数都是代理和回头客户介绍的所以一般现在有新的单子 我给客户的都是第一手的代理价格，因为我想坦诚对待大家 不想跟大家在价格方面浪费时间
对于老客户或者被老客户介绍过来的朋友，我们都会适当给一些优惠。
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
选择实体注册公司办理，更放心，更安全！我们的承诺：可来公司面谈，可签订合同，会陪同客户一起到教育部认证窗口递交认证材料，客户在教育部官方认证查询网站查询到认证通过结果后付款，不成功不收费！
学历顾问：微信：176555708
Top 10 Oil and Gas Projects in Saudi Arabia 2024.pdf
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Student information management system project report ii.pdf
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
6th International Conference on Machine Learning & Applications (CMLA 2024)
6th International Conference on Machine Learning & Applications (CMLA 2024) will provide an excellent international forum for sharing knowledge and results in theory, methodology and applications of on Machine Learning & Applications.
RAT: Retrieval Augmented Thoughts Elicit Context-Aware Reasoning in Long-Hori...
RAT: Retrieval Augmented Thoughts Elicit Context-Aware Reasoning in Long-Horizon Generation
Recently uploaded (20)
Design and Analysis of Algorithms-DP,Backtracking,Graphs,B&B
Design and Analysis of Algorithms-DP,Backtracking,Graphs,B&B
AKS UNIVERSITY Satna Final Year Project By OM Hardaha.pdf
AKS UNIVERSITY Satna Final Year Project By OM Hardaha.pdf
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...
Recycled Concrete Aggregate in Construction Part III
Recycled Concrete Aggregate in Construction Part III
Fundamentals of Electric Drives and its applications.pptx
Fundamentals of Electric Drives and its applications.pptx
block diagram and signal flow graph representation
block diagram and signal flow graph representation
Top 10 Oil and Gas Projects in Saudi Arabia 2024.pdf
Top 10 Oil and Gas Projects in Saudi Arabia 2024.pdf
Student information management system project report ii.pdf
Student information management system project report ii.pdf
6th International Conference on Machine Learning & Applications (CMLA 2024)
6th International Conference on Machine Learning & Applications (CMLA 2024)
RAT: Retrieval Augmented Thoughts Elicit Context-Aware Reasoning in Long-Hori...
RAT: Retrieval Augmented Thoughts Elicit Context-Aware Reasoning in Long-Hori...
Tutorial for 16S rRNA Gene Analysis with QIIME2.pdf
Tutorial for 16S rRNA Gene Analysis with QIIME2.pdf
Single-Phase Grid-tied Transformerless Inverter of Zero Leakage Current for PV System
- 1. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 Single-Phase Grid-tied Transformerless Inverter of Zero Leakage Current for PV System ABSTRACT: Multi-level transformerless inverters are widely used in grid-tied PV systems since they characterized by higher efficiency and lower cost. In this context, new topologies, modulation, and control schemes were presented to solve problems of a common-mode voltage and leakage current. This work proposes a transformerless five-level inverter with zero leakage current and ability to reduce the harmonic output content for a grid-tied single-phase PV system. The neutral of the grid links to a common on which the negative and the positive terminals of the DC-link are connected via parasitic capacitors that can eliminate the leakage current. The proposed topology, with its inherent circuit structure, leads to boost the overall efficiency. Simulation and experimental results show almost zero leakage current and a high-quality output when maintaining balanced capacitor voltages on the DC-link input. The experimental results show 1.07% THD and 96.3 % maximum efficiency when injecting a power of 1.1 kW that verify the performance of the proposed inverter with PV sources. KEYWORDS: 1. IGBT inverters 2. Transformerless grid-connected photovoltaic inverter 3. Solar PV SOFTWARE: MATLAB/SIMULINK
- 2. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 CONCLUSION: A new high-performance transformerless 5L-NPC inverter with its control strategy for a grid-tied PV system has been presented. The major advantages of the presented system can be brief as follows: 1. The topology of employing diode clamping MLI with suitable stray capacitors makes the leakage current to flow through the system in a very low value reaches zero. Furthermore, the system offers a connection between the DC-link pass bar of a solar PV array with the grid neutral terminal that results in zero leakage current. 2. The operation of the employed five-level topology results in high performance for the harmonic distortion that allows the reduction of filter components as compared with lower MLIs. 3. The proposed 5L-NPC topology eliminated the CM leakage current with 1.07% THD by using eight power switches. The results confirmed the above-stated advantages, and the proposed system offers approximately similar characteristics in reactive and real power injections. Therefore, the proposed inverter topology and its modulation scheme were a suitable and attractive solution for single-phase grid-tied PV systems. Although the proposed 5L-NPC system achieved zero CM leakage current with a very- low THD, the design is limited by eight switches that are recommended to be reduced in future work. Moreover, the presented system solved the balancing issue of the DC-link capacitors’ voltages that required for proper operation by a modulation strategy inspired in [21], we recommend easier algorithms to solve such issue. REFERENCES: [1] S. Padmanaban et al., “A novel modified sine-cosine optimized MPPT algorithm for grid integrated PV system under real operating conditions,” IEEE Access, vol. 7, pp. 10467–10477, 2019. [2] N. Priyadarshi, S. Padmanaban, M. S. Bhaskar, F. Blaabjerg, and A. Sharma, “Fuzzy SVPWM-based inverter control realisation of grid integrated photovoltaicwind system with fuzzy particle swarm optimisation maximum power point tracking algorithm for a gridconnected
- 3. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 PV/wind power generation system: Hardware implementation,” IET Electr. Power Appl., vol. 12, no. 7, pp. 962– 971, 2018. [3] N. Priyadarshi, S. Padmanaban, P. Kiran Maroti, and A. Sharma, “An Extensive Practical Investigation of FPSO-Based MPPT for Grid Integrated PV System under Variable Operating Conditions with Anti-Islanding Protection,” IEEE Syst. J., vol. 13, no. 2, pp. 1861–1871, 2019. [4] N. Priyadarshi, S. Padmanaban, J. B. Holm-Nielsen, F. Blaabjerg, and M. S. Bhaskar, “An Experimental Estimation of Hybrid ANFIS–PSO-Based MPPT for PV Grid Integration Under Fluctuating Sun Irradiance,” IEEE Syst. J., vol. PP, pp. 1–12, 2019. [5] N. Priyadarshi, S. Padmanaban, S. Member, M. S. Bhaskar, and F. Blaabjerg, “A Hybrid Photovoltaic-Fuel Cell-Based Single-Stage Grid Integration With Lyapunov Control Scheme,” IEEE Syst. J., vol. PP, pp. 1–9, 2019.