Power quality improvement in distribution network using DSTATCOM with battery energy storage system
•
0 likes•189 views
The distribution static compensator (DSTATCOM) provides fast control of active and reactive powers to enable load compensation, harmonics current elimination, voltage flicker mitigation, voltage and frequency regulation. This paper presents power quality improvement technique in the presence of grid disturbances and wind energy penetration using DSTATCOM with battery energy storage system. DSTATCOM control is provided based on synchronous reference frame theory. A modified IEEE 13 bus test feeder with DSTATCOM and wind generator is used for the study. Power quality events during grid disturbances such as feeder tripping and re-closing, voltage sag, swell and load switching have been studied in association with DSTATCOM. The power quality disturbances due to wind generator outage, synchronization and wind speed variations have also been investigated. The study has been carried out using MATLAB/SIMULINK and the simulation results are compared with real time results obtained by the use of real time digital simulator (RTDS) for validating the effectiveness of proposed methodology. The proposed method has been proved to be effective in improvement of power quality with all disturbances stated above.
Report
Share
Report
Share
Download to read offline
Recommended
A three phase grid tied spv system with adaptive dc link voltage for cpi volt...
This paper deals with a three-phase two-stage grid tied SPV (solar photo-voltaic) system. The first stage is a boost converter, which serves the purpose of MPPT (maximum power point tracking) and feeding the extracted solar energy to the DC link of the PV inverter, whereas the second stage is a two-level VSC (voltage source converter) serving as PV inverter which feeds power from a boost converter into the grid. The proposed system uses an adaptive DC link voltage which is made adaptive by adjusting reference DC link voltage according to CPI (common point of interconnection) voltage. The adaptive DC link voltage control helps in the reduction of switching power losses. A feed forward term for solar contribution is used to improve the dynamic response. The system is tested considering realistic grid voltage variations for under voltage and over voltage. The performance improvement is verified experimentally. The proposed system is advantageous not only in cases of frequent and sustained under voltage (as in the cases of far radial ends of Indian grid) but also in case of normal voltages at CPI. The THD (total harmonics distortion) of grid current has been found well under the limit of an IEEE-519 standard.
Model predictive control of pv sources in a smart dc distribution system maxi...
In a dc distribution system, where multiple power sources supply a common bus, current sharing is an important issue. When renewable energy resources are considered, such as photovoltaic (PV), dc/dc converters are needed to decouple the source voltage, which can vary due to operating conditions and maximum power point tracking (MPPT), from the dc bus voltage. Since different sources may have different power delivery capacities that may vary with time, coordination of the interface to the bus is of paramount importance to ensure reliable system operation. Further, since these sources are most likely distributed throughout\ the system, distributed controls are needed to ensure a robust and fault tolerant control system. This paper presents a model predictive control-based MPPT and model predictive control-based droop current regulator to interface PV in smart dc distribution systems. Back-to-back dc/dc converters control both the input current from the PV module and the droop characteristic of the output current injected into the distribution bus. The predictive controller speeds up both of the control loops, since it predicts and corrects error before the switching signal is applied to the respective converter.
Voltage sag enhancement of grid connected hybrid pv wind power system using b...
Renewable energy sources; which are abundant in nature and climate friendly are the only preferable choice of the world to provide green energy. The limitation of most renewable energy sources specifically wind and solar PV is its intermittent nature which are depend on wind speed and solar irradiance respectively and this leads to power fluctuations. To compensate and protect sensitive loads from being affected by the power distribution side fluctuations and faults, dynamic voltage restorer (DVR) is commonly used. This research work attempts to withstand and secure the effect of voltage fluctuation of grid connected hybrid PV-wind power system. To do so battery and super magnetic energy storage (SMES) based DVR is used as a compensating device in case of voltage sag condition. The compensation method used is a pre-sag compensation which locks the instantaneous real time three phase voltage magnitude and angle in normal condition at the point of common coupling (PCC) and stores independently so that during a disturbance it used for compensation. Symmetrical and asymmetrical voltage sags scenario are considered and compensation is carried out using Power System Computer Aided Design or Electro Magnetic Transient Design and Control (PSCAD/EMTDC) software.
Voltage sag enhancement of grid connected hybrid pv wind power system using b...
Renewable energy sources; which are abundant in nature and climate friendly are the only preferable choice of the world to provide green energy. The limitation of most renewable energy sources specifically wind and solar PV is its intermittent nature which are depend on wind speed and solar irradiance respectively and this leads to power fluctuations. To compensate and protect sensitive loads from being affected by the power distribution side fluctuations and faults, dynamic voltage restorer (DVR) is commonly used. This research work attempts to withstand and secure the effect of voltage fluctuation of grid connected hybrid PV-wind power system. To do so battery and super magnetic energy storage (SMES) based DVR is used as a compensating device in case of voltage sag condition. The compensation method used is a pre-sag compensation which locks the instantaneous real time three phase voltage magnitude and angle in normal condition at the point of common coupling (PCC) and stores independently so that during a disturbance it used for compensation. Symmetrical and asymmetrical voltage sags scenario are considered and compensation is carried out using Power System Computer Aided Design or Electro Magnetic Transient Design and Control (PSCAD/EMTDC) software.
Control strategy for power flow management in a pv system supplying dc loads
The growing concern for energy saving has increased the usage of LED-based street lights, electronic chokes, compact fluorescent lamps, and inverter-fed drives. Hence, the load profile seen by the electrical grid is undergoing a notable change as these devices have to operate from a dc source. Photovoltaics (PV) being a major energy source, the aforementioned loads can be connected directly to the dc bus. A grid-connected PV system involves a power source (PV array), a power sink (load), and two power sources/sink (utility and battery), and hence, a power
flow management system is required to balance the power flow among these sources. One such system is developed for selecting the operating mode of the bidirectional converter by sensing the battery voltage. The viability of the scheme has been ascertained by performing experimental studies on a laboratory prototype. The control strategy is digitally implemented on an Altera Cyclone II Field Programmable Gate Array (FPGA) board, and the algorithm is verified for different modes of operation by varying the load. Experimental results are presented to bring out
the usefulness of the control strategy.
A Unified Control and Power Management Scheme for PV-Battery-Based Hybrid Mic...
Battery storage is usually employed in Photovoltaic (PV) system to mitigate the power fluctuations due to the characteristics of PV panels and solar irradiance. Control schemes for PV-battery systems must be able to stabilize the bus voltages as well as to control the power flows flexibly. This paper proposes a comprehensive control and power management system (CAPMS) for PV-battery-based hybrid microgrids with both AC and DC buses, for both grid-connected and islanded modes. The proposed CAPMS is successful in regulating the DC and AC bus voltages and frequency stably, controlling the voltage and power of each unit flexibly, and balancing the power flows in the systems automatically under different operating circumstances, regardless of disturbances from switching operating modes, fluctuations of irradiance and temperature, and change of loads. Both simulation and experimental case studies are carried out to verify the performance of the proposed method.
An f p q droop control in cascaded-type microgrid
In cascaded-type microgrid, the synchronization and power balance of distributed generators become two new issues that needs to be addressed urgently. To that end, an f-P/Q droop control is proposed in this letter, and its stability is analyzed as well. This proposed droop control is capable to achieve power balance under both resistive-inductive an resistive-capacitive loads autonomously. Compared with the inverse power factor droop control, an obvious advantage consists in extending the scope of application. Finally, the feasibility of the proposed method is verified by simulation results.
Performance enhancement of actively controlled hybrid dc microgrid incorporat...
In this paper, a new energy control scheme is proposed for actively controlled hybrid dc microgrid to reduce the adverse impact of pulsed power loads. The proposed energy control is an adaptive current-voltage control (ACVC) scheme based on the moving average measurement technique and an adaptive proportional compensator. Unlike conventional energy control methods, the proposed ACVC approach has the advantage of controlling both voltage and current of the system while keeping the output current of the power converter at a relatively constant value. For this study, a laboratory scale hybrid dc microgrid is developed to evaluate the performance of the ACVC strategy and to compare its performance with the other conventional energy control methods. Using experimental test results, it is shown that the proposed strategy highly improves the dynamic performance of the hybrid dc microgrid. Although the ACVC technique causes slightly more bus voltage variation, it effectively eliminates the high current and power pulsation of the power converters. The experimental test results for different pulse duty ratios demonstrated a significant improvement achieved by the developed ACVC scheme in enhancing the system efficiency, reducing the ac grid voltage drop and the frequency fluctuations.
Recommended
A three phase grid tied spv system with adaptive dc link voltage for cpi volt...
This paper deals with a three-phase two-stage grid tied SPV (solar photo-voltaic) system. The first stage is a boost converter, which serves the purpose of MPPT (maximum power point tracking) and feeding the extracted solar energy to the DC link of the PV inverter, whereas the second stage is a two-level VSC (voltage source converter) serving as PV inverter which feeds power from a boost converter into the grid. The proposed system uses an adaptive DC link voltage which is made adaptive by adjusting reference DC link voltage according to CPI (common point of interconnection) voltage. The adaptive DC link voltage control helps in the reduction of switching power losses. A feed forward term for solar contribution is used to improve the dynamic response. The system is tested considering realistic grid voltage variations for under voltage and over voltage. The performance improvement is verified experimentally. The proposed system is advantageous not only in cases of frequent and sustained under voltage (as in the cases of far radial ends of Indian grid) but also in case of normal voltages at CPI. The THD (total harmonics distortion) of grid current has been found well under the limit of an IEEE-519 standard.
Model predictive control of pv sources in a smart dc distribution system maxi...
In a dc distribution system, where multiple power sources supply a common bus, current sharing is an important issue. When renewable energy resources are considered, such as photovoltaic (PV), dc/dc converters are needed to decouple the source voltage, which can vary due to operating conditions and maximum power point tracking (MPPT), from the dc bus voltage. Since different sources may have different power delivery capacities that may vary with time, coordination of the interface to the bus is of paramount importance to ensure reliable system operation. Further, since these sources are most likely distributed throughout\ the system, distributed controls are needed to ensure a robust and fault tolerant control system. This paper presents a model predictive control-based MPPT and model predictive control-based droop current regulator to interface PV in smart dc distribution systems. Back-to-back dc/dc converters control both the input current from the PV module and the droop characteristic of the output current injected into the distribution bus. The predictive controller speeds up both of the control loops, since it predicts and corrects error before the switching signal is applied to the respective converter.
Voltage sag enhancement of grid connected hybrid pv wind power system using b...
Renewable energy sources; which are abundant in nature and climate friendly are the only preferable choice of the world to provide green energy. The limitation of most renewable energy sources specifically wind and solar PV is its intermittent nature which are depend on wind speed and solar irradiance respectively and this leads to power fluctuations. To compensate and protect sensitive loads from being affected by the power distribution side fluctuations and faults, dynamic voltage restorer (DVR) is commonly used. This research work attempts to withstand and secure the effect of voltage fluctuation of grid connected hybrid PV-wind power system. To do so battery and super magnetic energy storage (SMES) based DVR is used as a compensating device in case of voltage sag condition. The compensation method used is a pre-sag compensation which locks the instantaneous real time three phase voltage magnitude and angle in normal condition at the point of common coupling (PCC) and stores independently so that during a disturbance it used for compensation. Symmetrical and asymmetrical voltage sags scenario are considered and compensation is carried out using Power System Computer Aided Design or Electro Magnetic Transient Design and Control (PSCAD/EMTDC) software.
Voltage sag enhancement of grid connected hybrid pv wind power system using b...
Renewable energy sources; which are abundant in nature and climate friendly are the only preferable choice of the world to provide green energy. The limitation of most renewable energy sources specifically wind and solar PV is its intermittent nature which are depend on wind speed and solar irradiance respectively and this leads to power fluctuations. To compensate and protect sensitive loads from being affected by the power distribution side fluctuations and faults, dynamic voltage restorer (DVR) is commonly used. This research work attempts to withstand and secure the effect of voltage fluctuation of grid connected hybrid PV-wind power system. To do so battery and super magnetic energy storage (SMES) based DVR is used as a compensating device in case of voltage sag condition. The compensation method used is a pre-sag compensation which locks the instantaneous real time three phase voltage magnitude and angle in normal condition at the point of common coupling (PCC) and stores independently so that during a disturbance it used for compensation. Symmetrical and asymmetrical voltage sags scenario are considered and compensation is carried out using Power System Computer Aided Design or Electro Magnetic Transient Design and Control (PSCAD/EMTDC) software.
Control strategy for power flow management in a pv system supplying dc loads
The growing concern for energy saving has increased the usage of LED-based street lights, electronic chokes, compact fluorescent lamps, and inverter-fed drives. Hence, the load profile seen by the electrical grid is undergoing a notable change as these devices have to operate from a dc source. Photovoltaics (PV) being a major energy source, the aforementioned loads can be connected directly to the dc bus. A grid-connected PV system involves a power source (PV array), a power sink (load), and two power sources/sink (utility and battery), and hence, a power
flow management system is required to balance the power flow among these sources. One such system is developed for selecting the operating mode of the bidirectional converter by sensing the battery voltage. The viability of the scheme has been ascertained by performing experimental studies on a laboratory prototype. The control strategy is digitally implemented on an Altera Cyclone II Field Programmable Gate Array (FPGA) board, and the algorithm is verified for different modes of operation by varying the load. Experimental results are presented to bring out
the usefulness of the control strategy.
A Unified Control and Power Management Scheme for PV-Battery-Based Hybrid Mic...
Battery storage is usually employed in Photovoltaic (PV) system to mitigate the power fluctuations due to the characteristics of PV panels and solar irradiance. Control schemes for PV-battery systems must be able to stabilize the bus voltages as well as to control the power flows flexibly. This paper proposes a comprehensive control and power management system (CAPMS) for PV-battery-based hybrid microgrids with both AC and DC buses, for both grid-connected and islanded modes. The proposed CAPMS is successful in regulating the DC and AC bus voltages and frequency stably, controlling the voltage and power of each unit flexibly, and balancing the power flows in the systems automatically under different operating circumstances, regardless of disturbances from switching operating modes, fluctuations of irradiance and temperature, and change of loads. Both simulation and experimental case studies are carried out to verify the performance of the proposed method.
An f p q droop control in cascaded-type microgrid
In cascaded-type microgrid, the synchronization and power balance of distributed generators become two new issues that needs to be addressed urgently. To that end, an f-P/Q droop control is proposed in this letter, and its stability is analyzed as well. This proposed droop control is capable to achieve power balance under both resistive-inductive an resistive-capacitive loads autonomously. Compared with the inverse power factor droop control, an obvious advantage consists in extending the scope of application. Finally, the feasibility of the proposed method is verified by simulation results.
Performance enhancement of actively controlled hybrid dc microgrid incorporat...
In this paper, a new energy control scheme is proposed for actively controlled hybrid dc microgrid to reduce the adverse impact of pulsed power loads. The proposed energy control is an adaptive current-voltage control (ACVC) scheme based on the moving average measurement technique and an adaptive proportional compensator. Unlike conventional energy control methods, the proposed ACVC approach has the advantage of controlling both voltage and current of the system while keeping the output current of the power converter at a relatively constant value. For this study, a laboratory scale hybrid dc microgrid is developed to evaluate the performance of the ACVC strategy and to compare its performance with the other conventional energy control methods. Using experimental test results, it is shown that the proposed strategy highly improves the dynamic performance of the hybrid dc microgrid. Although the ACVC technique causes slightly more bus voltage variation, it effectively eliminates the high current and power pulsation of the power converters. The experimental test results for different pulse duty ratios demonstrated a significant improvement achieved by the developed ACVC scheme in enhancing the system efficiency, reducing the ac grid voltage drop and the frequency fluctuations.
Development of wind and solar based ac microgrid with power quality improveme...
This work proposes a microgrid (μ-grid) integrating wind and solar photovoltaic (PV) resources, along with the battery energy storage (BES) to the three phase grid feeding the nonlinear load. The μ-grid disconcerted by probabilistic nonlinear time dependent parameters and their effects are compensated by cohesive controllers used for utility grid side voltage source converter (GVSC) and machine side VSC (MVSC). The switching controls and the reconfigurability of the μ-grid are addressed on imperative aspects of improving power quality (PQ), power reliability, nonlinear load compensation and economic utilization of resources. The nonlinear load compensation and PQ enhancement are achieved by executing modified version of the adaptive filtering technique including “momentum” based least mean square (MLMS) control technique, utilized for providing the switching control signals to the GVSC. It utilizes two preceding gradient weights for obtaining updated weight thereby improving the convergence rate and overcoming the limitation of conventional control of the same family. The MVSC acquires its switching signals from conventional vector control scheme and the encoderless estimation of speed and rotor position of the synchronous generator (SG) driven by wind turbine through back electromotive force control technique. The external environmental disturbances are overcome by utilizing perturb and observe (P&O) maximum power point (MPP) for wind optimal power extraction and adaptive P&O with variable perturbation step size for solar MPP estimation. Test results are obtained from the laboratory prototype under steady state and dynamic conditions including altering wind speed, intermittent solar insolation and variable load conditions. The PQ issues are addressed and investigated successfully.
Statcom for improved dynamic performance of wind farms in power grid
Application of FACTS controller called Static Synchronous Compensator STATCOM to improve the performance of power grid with Wind Farms is investigated .The essential feature of the STATCOM is that it has the ability to absorb or inject fastly the reactive power with power grid . Therefore the voltage regulation of the power grid with STATCOM FACTS device is achieved. Moreover restoring the stability of the power system having wind farm after occurring
severe disturbance such as faults or wind farm mechanical power variation is obtained with STATCOM controller . The dynamic model of the power system having wind farm controlled by
proposed STATCOM is developed . To Validate the powerful of the STATCOM FACTS controller , the studied power system is simulated and subjected to different severe disturbances . The results prove the effectiveness of the proposed STATCOM controller in terms of fast damping the power system oscillations and restoring the power system stability .
Power Quality Assessment of Voltage Positive Feedback Based Islanding Detecti...
Islanding refers to a condition where distributed generators (DGs) inject power solely to the local load after electrical separation from power grid. Several islanding detection methods (IDMs) categorized into remote, active, and passive groups have been reported to detect this undesirable state. In active techniques, a disturbance is injected into the DG’s controller to drift a local yardstick out of the permissible range. Although this disturbance leads to more effective detections even in well-balanced island, it raises the total harmonic distortion (THD) of the output current under the normal operation conditions. This paper analyzes the power quality aspect of the modified sliding mode controller as a new active IDM for grid-connected photovoltaic system (GCPVS) with a string inverter. Its performance is compared with the voltage positive feedback (VPF) method, a well-known active IDM. This evaluation is carried out for a 1 kWp GCPVS in MATLAB/Simulink platform by measuring the output current harmonics and THD as well as the efficiency under various penetration and disturbance levels. The output results demonstrate that since the proposed disturbance changes the amplitude of the output current, it does not generate harmonics/subharmonics. Thereby, it has a negligible adverse effect on power quality. It is finally concluded that the performance of the sliding mode-based IDM is reliable from the standpoints of islanding detection and power quality.
A New Circuit of Modular Multilevel Inverter for Grid-Connected Photovoltaic ...
This study presents a new circuit topology of the Modular Multilevel Converter (MMC) which is deployed for photovoltaic grid applications. In the conventional MMC, two arm inductors are placed in each phase to limit the circulating current. In the proposed topology, the inductors are replaced by a transformer. The proposed circuit gives a 50% reduction of the voltage rating of the power devices and the capacitors in comparison with the conventional MMC. The required dc-link voltage which is fed directly by PV panels is also reduced by half. The paper presents a PWM method to control the solar inverter output voltage. The proposed concept is confirmed through simulation and experimental results.
Single-Stage Switched-Capacitor Module (S3CM) Topology for Cascaded Multileve...
A two-stage switched-capacitor based multilevel inverter possesses a drawback such that switches in the second stage (i.e. H-bridge) endure higher voltage stress. To resolve this problem, this letter proposes a single-stage switched-capacitor module (S3CM) topology for cascaded multilevel inverter which ensures the peak inverse voltage across all switches within the dc source voltage. Nine voltage levels can be generated with only one dc source and two incorporated capacitors. Hence, the number of isolated dc sources are significantly reduced compared to cascaded H-bridge. In addition, voltage boosting gain of two is achieved. A comparative analysis against the recent topology reveals that the proposed S3CM topology achieves switch count reduction. The operation of the proposed topology is validated through circuit analysis followed by experimental results of a single module (9-level) prototype.
Novel High Performance Stand Alone Solar PV System with High Gain, High Effic...
This paper proposes a novel 3- stand-alone solar PV system configuration that uses high gain, high efficiency (96%) dc-dc converters both in the forward power stage as well as the bidirectional battery interface. The high voltage gain converters enable the use of low voltage PV and battery sources. This results in minimization of partial shading and parasitic capacitance effects on the PV source. Series connection of a large number of battery modules is obviated, preventing the overcharging and deep discharging issues that reduce the battery life. Also, the proposed configuration facilitates "required power tracking (RPT)" of the PV source as per the load requirements eliminating the use of expensive and 'difficult to manage' dump loads. High performance inverter operation is achieved through abc to dq reference frame transformation, which helps in generating precise information about the load's active power component for RPT, regulation of ac output voltage and minimization of control complexity. Inverter output voltage is regulated by controlling the modulation index of sinusoidal pulse width modulation, resulting in a stable and reliable system operation. The active power demand is controlled by regulating the dc link voltage. All the analytical, simulation and experimental results of this work are presented.
Improving the Dynamic Performance of Wind Farms with STATCOM
When integrated to the power system, large wind farms can pose voltage control issues among
other problems. A thorough study is needed to identify the potential problems and to develop
measures to mitigate them. Although integration of high levels of wind power into an existing
transmission system does not require a major redesign, it necessitates additional control and
compensating equipment to enable (fast) recovery from severe system disturbances. The use of a
Static Synchronous Compensator (STATCOM) near a wind farm is investigated for the purpose
of stabilizing the grid voltage after grid-side disturbance such as a three phase short circuit fault.
The strategy focuses on a fundamental grid operational requirement to maintain proper voltages
at the point of common coupling by regulating the voltage. The DC voltage at individual wind
turbine (WT) inverters is also stabilized to facilitate continuous operation of wind turbines
during disturbances.
Design and Control of Wind integrated Shunt Active Power Filter to Improve Po...
In this paper wind energy conservation system (WECS) with shunt active power filter (SAPF) is proposed for harmonics elimination, power factor correction, reactive power compensation and grid current balancing. Adaptive neuro fuzzy inference system (ANFIS) based controller is implemented at WECS side to control the boost converter to achieve MPP and at SAPF sides to minimize voltage variations and enhance power quality. Here, synchronous reference frame (SRF) theory based reference current generation technique is employed in SAPF. The proposed scheme is implemented in MATLAB/Simulink. The results confirm that this method has better performance and can maintain total harmonic distortion (THD) level of the system within the IEEE standard 519.
Mppt with single dc–dc converter and inverter for grid connected hybrid wind-...
A new topology of a hybrid distributed generator based on photovoltaic and wind-driven permanent magnet synchronous generator is proposed. In this generator, the sources are connected together to the grid with the help of only a single boost converter followed by an inverter. Thus, compared to earlier schemes, the proposed scheme has fewer power converters. A model of the proposed scheme in the d − q-axis reference frame is developed. Two low-cost controllers are also proposed for the new hybrid scheme to separately trigger the dc–dc converter and the inverter for tracking the maximum power from both sources. The integrated operations of both proposed controllers for different conditions are demonstrated through simulation and experimentation. The steady-state performance of the system and the transient response of the controllers are also presented to demonstrate the successful operation of the new hybrid system. Comparisons of experimental and simulation results are given to validate the simulation model.
Voltage Sag and Swell Mitigation Using DSTATCOM in Renewable Energy Based Dis...
Renewable distributed generation systems are an alternative solution to provide energy locally near customers. However, the supplying of power without disturbance is the main challenge for utilities, especially for systems that integrate fluctuating renewable sources which can cause voltage sag and swell. In this paper, voltage sag and swell issues are investigated. The first studied scenario is related to the disturbance of the energy source and the second one is due to the installation of a heavy load with a sensitive load at the same supplying bus. A D-STATCOM is connected at the point of common coupling (pCC) to mitigate the voltage sag and sell problems. An energy storage battery has been installed at the DC-side of the compensator that gives the possibility to control the voltage at the PCC and exchange the active and reactive power with the grid. A linear proportional integral (PI) feed-forward controller supervises the compensator. The obtained results show that the D-STATCOM compensator behaves as a good solution to mitigate the voltage sag and swell in distribution grid.
Permanent Magnet Synchronous Generator-Based Standalone Wind Energy Supply Sy...
In this paper, a novel algorithm, based on dc link voltage, is proposed for effective energy management of a standalone permanent magnet synchronous generator (PMSG)-based variable speed wind energy conversion system consisting of battery, fuel cell, and dump load (i.e., electrolyzer). Moreover, by maintaining the dc link voltage at its reference value, the output ac voltage of the inverter can be kept constant irrespective of variations in the wind speed and load. An effective control technique for the inverter, based on the pulse width modulation (PWM) scheme, has been developed to make the line voltages at the point of common coupling (PCC) balanced when the load is unbalanced. Similarly, a proper control of battery current through dc–dc converter has been carried out to reduce the electrical torque pulsation of the PMSG under an unbalanced load scenario. Based on extensive simulation results using MATLAB/SIMULINK, it has been established that the performance of the controllers both in transient as well as in steady state is quite satisfactory and it can also maintain maximum power point tracking.
Front end buck rectifier with reduced filter size and single-loop control
This paper presents a transformerless solution for front-end rectification, which is particularly suitable for traction applications, requiring high voltages to be stepped down to appropriate dc voltage. The proposed topology is based on pulse widthmodulation buck rectifier (current source inverter topology) and is capable of rectification and stepping down of single-phase ac supply, in a single stage. A new control scheme is proposed to achieve constant dc output voltage and sinusoidal source current, irrespective of large ripples in the dc inductor current. The proposed scheme is configured in single-loop voltage control mode. The relevant small-signal model is derived from the large-signal model using multi order decomposition. An elaborate procedure of dc filter design is discussed, for circuit operation with minimum energy storage. All analytical results are validated by numerical simulation for sinusoidal and distorted source voltage. Experimental verification is achieved through a 1.2-kW grid-connected laboratory prototype.
Irradiance-adaptive PV Module Integrated Converter for High Efficiency and Po...
The strive for efficient and cost-effective photovoltaic systems motivated the power electronic design developed here. The work resulted in a DC-DC converter for module integration and distributed maximum power point tracking (MPPT) with a novel adaptive control scheme. The latter is essential for the combined features of high energy efficiency and high power quality over a wide range of operating conditions. The switching frequency is optimally modulated as a function of solar irradiance for power conversion efficiency maximization. With the rise of irradiance, the frequency is reduced to reach the conversion efficiency target. A search algorithm is developed to determine the optimal switching frequency step. Reducing the switching frequency may, however, compromise MPPT efficiency. Furthermore, it leads to increased ripple content. Therefore, to achieve a uniform high power quality at all conditions, interleaved converter cells are adaptively activated. The overall cost is kept low by selecting components that allow for implementing the functions at low cost. Simulation results show the high value of the module integrated converter for DC standalone and microgrid applications. A 400 W prototype was implemented at 0.14 Euro/W. Testing showed efficiencies above 95% taking into account all losses from power conversion, MPPT, and measurement and control circuitry.
A Sensorless Power Reserve Control Strategy for Two-Stage Grid-Connected PV S...
Due to the still increasing penetration of grid connected Photovoltaic (PV) systems, advanced active power control functionalities have been introduced in grid regulations. A power reserve control, where namely the active power from the PV panels is reserved during operation, is required for grid support. In this paper, a cost-effective solution to realize the power reserve for two-stage grid-connected PV systems is proposed. The proposed solution routinely employs a Maximum Power Point Tracking (MPPT) control to estimate the available PV power and a Constant Power Generation (CPG) control to achieve the power reserve. In this method, the solar irradiance and temperature measurements that have been used in conventional power reserve control schemes to estimate the available PV power are not required, and thereby being a sensorless approach with reduced cost. Experimental tests have been performed on a 3-kW two-stage single-phase grid-connected PV system, where the power reserve control is achieved upon demands.
Maximum power extraction from wind energy system based on fuzzy logic control
This paper proposes a variable speed control scheme for grid-connected wind energy conversion system (WECS) using permanent magnet synchronous generator (PMSG). The control algorithm tracks the maximum power for wind speeds below rated speed of wind turbines and ensures the power will not go over the rated power for wind speeds over the rated value. The control algorithm employs fuzzy logic controller (FLC) to effectively do this target. The wind turbine is connected to the grid via back-to-back PWM-VSC. Two effective computer simulation packages (PSIM and Simulink) are used to carry out the simulation effectively. The control system has two controllers for generator side and grid side converters. The main function of the generator side controller is to track the maximum power through controlling the rotational speed of the wind turbine using FLC. In the grid side converter, active and reactive power control has been achieved by controlling q-axis and d-axis current components, respectively. The d-axis current is set at zero for unity power factor and the q-axis current is controlled to deliver the power flowing from the dc-link to the electric utility grid.
Comparison of Modulation Techniques for Matrix Converter
Matrix Converters can directly convert an ac power supply of fixed voltage into an ac voltage of variable amplitude and frequency. Matrix Converter is a single stage converter. The matrix converters can contribute to the realization of low volume, sinusoidal input current, bidirectional power flow and lack of bulky reactive elements. All the reasons lead to the development of matrix converter. Based on the control techniques used in the matrix converter, the performance varies. So this paper analyses the performance of matrix converter with three different modulation techniques such as PWM, SVPWM and SVM. The basic principle and switching sequence of these modulation techniques are presented in this paper. The output voltage, output current waveforms, voltage transfer ratio and THD spectrum of switching waveforms connected to RL load are analyzed by using Matlab/Simulink software. The simulated results are analyzed and show that the THD is better for SVM technique.
Designing of multilevel dpfc to improve power quality
According to growth of electricity demand and the increased number of non-linear loads in power grids, providing a high quality electrical power should be considered. In this paper, Enhancement of power quality by using fuzzy based multilevel power flow controller (DPFC) is proposed. The DPFC is a new FACTS device, which its structure is similar to unified power flow controller (UPFC). In spite of UPFC, in DPFC the common dc-link between the shunt and series converters is eliminated and three-phase series converter is divided to several single-phase series distributed converters through the line. This eventually enables the DPFC to fully control all power system parameters. It, also, increases the reliability of the device and reduces its cost simultaneously. In recent years multi level inverters are used high power and high voltage applications .Multilevel inverter output voltage produce a staircase output waveform, this waveform look like a sinusoidal waveform leads to reduction in Harmonics. Fuzzy Logic is used for optimal designing of controller parameters. Application of Fuzzy Multilevel DPFC for reduction of Total Harmonic Distortion was presented. The simulation results show the improvement of power quality using DPFC with Fuzzy logic controller.
New ac dc power factor correction architecture suitable for high frequency op...
This paper presents a novel ac-dc power factor correction (PFC) power conversion architecture for single-phase grid interface. The proposed architecture has significant advantages for achieving high efficiency, good power factor, and converter miniaturization, especially in low-to-medium power applications. The architecture enables twice-line-frequency energy to be buffered at high voltage with a large voltage swing, enabling reduction in the energy buffer capacitor size, and elimination of electrolytic capacitors. While this architecture can be beneficial with a variety of converter topologies, it is especially suited for system miniaturization by enabling designs that operate at high frequency (HF, 3 – 30 MHz). Moreover, we introduce circuit implementations that provide efficient operation in this range. The proposed approach is demonstrated for an LED driver converter operating at a (variable) HF switching frequency (3 – 10 MHz) from 120Vac, and supplying a 35Vdc output at up to 30W. The prototype converter achieves high efficiency (92 %) and power factor (0.89), and maintains good performance over a wide load range. Owing to architecture and HF operation, the prototype achieves a high ‘box’ power density of 50W/ in3 (‘displacement’ power density of 130W/ in3), with miniaturized inductors, ceramic energy buffer capacitors, and a small-volume EMI filter.
Hybrid Modulation Concept for Five-Level Active-Neutral-Point-Clamped Converter
In this letter, a hybrid modulation concept consisting of three-level space vector modulation (3L-SVM) and phase-shifted pulse width modulation (PS-PWM) is proposed for five-level active neutral- point-clamped (5L-ANPC) converter. Under this concept, a simpler 3L-SVM plus PS-PWM scheme is applied to realize 5L modulation, instead of using complex 5L-SVM. The control of neutral voltage, flying capacitor voltage, and the improved dc voltage utilization are all implemented. With the help of the proposed concept, well-developed 3L-SVM schemes can be directly applied to the 5L-ANPC converter, which significantly simplify the gating signal generation. This concept can also be applied to other hybrid clamped 5L converters with two dc-link capacitors. It provides a unique solution, which utilize lower level SVM scheme to control higher level multilevel converters.
Power Quality Improvement in Solar Fed Cascaded Multilevel Inverter with Outp...
The presence of harmonics in solar Photo Voltaic (PV) energy conversion system results in deterioration of power quality. To address such issue, this paper aims to investigate the elimination of harmonics in a solar fed cascaded fifteen level inverter with aid of Proportional Integral (PI), Artificial Neural Network (ANN) and Fuzzy Logic (FL) based controllers. Unlike other techniques, the proposed FLC based approach helps in obtaining reduced harmonic distortions that intend to an enhancement in power quality. In addition to the power quality improvement, this paper also proposed to provide output voltage regulation in terms of maintaining voltage and frequency at the inverter output end in compatible with the grid connection requirements. The simulations are performed in the MATLAB / Simulink environment for solar fed cascaded 15 level inverter incorporating PI, ANN and FL based controllers. To exhibit the proposed technique, a 3 kWp photovoltaic plant coupled to multilevel inverter is designed and hardware is demonstrated. All the three techniques are experimentally investigated with the measurement of power quality metrics along with establishing output voltage regulation.
More Related Content
What's hot
Development of wind and solar based ac microgrid with power quality improveme...
This work proposes a microgrid (μ-grid) integrating wind and solar photovoltaic (PV) resources, along with the battery energy storage (BES) to the three phase grid feeding the nonlinear load. The μ-grid disconcerted by probabilistic nonlinear time dependent parameters and their effects are compensated by cohesive controllers used for utility grid side voltage source converter (GVSC) and machine side VSC (MVSC). The switching controls and the reconfigurability of the μ-grid are addressed on imperative aspects of improving power quality (PQ), power reliability, nonlinear load compensation and economic utilization of resources. The nonlinear load compensation and PQ enhancement are achieved by executing modified version of the adaptive filtering technique including “momentum” based least mean square (MLMS) control technique, utilized for providing the switching control signals to the GVSC. It utilizes two preceding gradient weights for obtaining updated weight thereby improving the convergence rate and overcoming the limitation of conventional control of the same family. The MVSC acquires its switching signals from conventional vector control scheme and the encoderless estimation of speed and rotor position of the synchronous generator (SG) driven by wind turbine through back electromotive force control technique. The external environmental disturbances are overcome by utilizing perturb and observe (P&O) maximum power point (MPP) for wind optimal power extraction and adaptive P&O with variable perturbation step size for solar MPP estimation. Test results are obtained from the laboratory prototype under steady state and dynamic conditions including altering wind speed, intermittent solar insolation and variable load conditions. The PQ issues are addressed and investigated successfully.
Statcom for improved dynamic performance of wind farms in power grid
Application of FACTS controller called Static Synchronous Compensator STATCOM to improve the performance of power grid with Wind Farms is investigated .The essential feature of the STATCOM is that it has the ability to absorb or inject fastly the reactive power with power grid . Therefore the voltage regulation of the power grid with STATCOM FACTS device is achieved. Moreover restoring the stability of the power system having wind farm after occurring
severe disturbance such as faults or wind farm mechanical power variation is obtained with STATCOM controller . The dynamic model of the power system having wind farm controlled by
proposed STATCOM is developed . To Validate the powerful of the STATCOM FACTS controller , the studied power system is simulated and subjected to different severe disturbances . The results prove the effectiveness of the proposed STATCOM controller in terms of fast damping the power system oscillations and restoring the power system stability .
Power Quality Assessment of Voltage Positive Feedback Based Islanding Detecti...
Islanding refers to a condition where distributed generators (DGs) inject power solely to the local load after electrical separation from power grid. Several islanding detection methods (IDMs) categorized into remote, active, and passive groups have been reported to detect this undesirable state. In active techniques, a disturbance is injected into the DG’s controller to drift a local yardstick out of the permissible range. Although this disturbance leads to more effective detections even in well-balanced island, it raises the total harmonic distortion (THD) of the output current under the normal operation conditions. This paper analyzes the power quality aspect of the modified sliding mode controller as a new active IDM for grid-connected photovoltaic system (GCPVS) with a string inverter. Its performance is compared with the voltage positive feedback (VPF) method, a well-known active IDM. This evaluation is carried out for a 1 kWp GCPVS in MATLAB/Simulink platform by measuring the output current harmonics and THD as well as the efficiency under various penetration and disturbance levels. The output results demonstrate that since the proposed disturbance changes the amplitude of the output current, it does not generate harmonics/subharmonics. Thereby, it has a negligible adverse effect on power quality. It is finally concluded that the performance of the sliding mode-based IDM is reliable from the standpoints of islanding detection and power quality.
A New Circuit of Modular Multilevel Inverter for Grid-Connected Photovoltaic ...
This study presents a new circuit topology of the Modular Multilevel Converter (MMC) which is deployed for photovoltaic grid applications. In the conventional MMC, two arm inductors are placed in each phase to limit the circulating current. In the proposed topology, the inductors are replaced by a transformer. The proposed circuit gives a 50% reduction of the voltage rating of the power devices and the capacitors in comparison with the conventional MMC. The required dc-link voltage which is fed directly by PV panels is also reduced by half. The paper presents a PWM method to control the solar inverter output voltage. The proposed concept is confirmed through simulation and experimental results.
Single-Stage Switched-Capacitor Module (S3CM) Topology for Cascaded Multileve...
A two-stage switched-capacitor based multilevel inverter possesses a drawback such that switches in the second stage (i.e. H-bridge) endure higher voltage stress. To resolve this problem, this letter proposes a single-stage switched-capacitor module (S3CM) topology for cascaded multilevel inverter which ensures the peak inverse voltage across all switches within the dc source voltage. Nine voltage levels can be generated with only one dc source and two incorporated capacitors. Hence, the number of isolated dc sources are significantly reduced compared to cascaded H-bridge. In addition, voltage boosting gain of two is achieved. A comparative analysis against the recent topology reveals that the proposed S3CM topology achieves switch count reduction. The operation of the proposed topology is validated through circuit analysis followed by experimental results of a single module (9-level) prototype.
Novel High Performance Stand Alone Solar PV System with High Gain, High Effic...
This paper proposes a novel 3- stand-alone solar PV system configuration that uses high gain, high efficiency (96%) dc-dc converters both in the forward power stage as well as the bidirectional battery interface. The high voltage gain converters enable the use of low voltage PV and battery sources. This results in minimization of partial shading and parasitic capacitance effects on the PV source. Series connection of a large number of battery modules is obviated, preventing the overcharging and deep discharging issues that reduce the battery life. Also, the proposed configuration facilitates "required power tracking (RPT)" of the PV source as per the load requirements eliminating the use of expensive and 'difficult to manage' dump loads. High performance inverter operation is achieved through abc to dq reference frame transformation, which helps in generating precise information about the load's active power component for RPT, regulation of ac output voltage and minimization of control complexity. Inverter output voltage is regulated by controlling the modulation index of sinusoidal pulse width modulation, resulting in a stable and reliable system operation. The active power demand is controlled by regulating the dc link voltage. All the analytical, simulation and experimental results of this work are presented.
Improving the Dynamic Performance of Wind Farms with STATCOM
When integrated to the power system, large wind farms can pose voltage control issues among
other problems. A thorough study is needed to identify the potential problems and to develop
measures to mitigate them. Although integration of high levels of wind power into an existing
transmission system does not require a major redesign, it necessitates additional control and
compensating equipment to enable (fast) recovery from severe system disturbances. The use of a
Static Synchronous Compensator (STATCOM) near a wind farm is investigated for the purpose
of stabilizing the grid voltage after grid-side disturbance such as a three phase short circuit fault.
The strategy focuses on a fundamental grid operational requirement to maintain proper voltages
at the point of common coupling by regulating the voltage. The DC voltage at individual wind
turbine (WT) inverters is also stabilized to facilitate continuous operation of wind turbines
during disturbances.
Design and Control of Wind integrated Shunt Active Power Filter to Improve Po...
In this paper wind energy conservation system (WECS) with shunt active power filter (SAPF) is proposed for harmonics elimination, power factor correction, reactive power compensation and grid current balancing. Adaptive neuro fuzzy inference system (ANFIS) based controller is implemented at WECS side to control the boost converter to achieve MPP and at SAPF sides to minimize voltage variations and enhance power quality. Here, synchronous reference frame (SRF) theory based reference current generation technique is employed in SAPF. The proposed scheme is implemented in MATLAB/Simulink. The results confirm that this method has better performance and can maintain total harmonic distortion (THD) level of the system within the IEEE standard 519.
Mppt with single dc–dc converter and inverter for grid connected hybrid wind-...
A new topology of a hybrid distributed generator based on photovoltaic and wind-driven permanent magnet synchronous generator is proposed. In this generator, the sources are connected together to the grid with the help of only a single boost converter followed by an inverter. Thus, compared to earlier schemes, the proposed scheme has fewer power converters. A model of the proposed scheme in the d − q-axis reference frame is developed. Two low-cost controllers are also proposed for the new hybrid scheme to separately trigger the dc–dc converter and the inverter for tracking the maximum power from both sources. The integrated operations of both proposed controllers for different conditions are demonstrated through simulation and experimentation. The steady-state performance of the system and the transient response of the controllers are also presented to demonstrate the successful operation of the new hybrid system. Comparisons of experimental and simulation results are given to validate the simulation model.
Voltage Sag and Swell Mitigation Using DSTATCOM in Renewable Energy Based Dis...
Renewable distributed generation systems are an alternative solution to provide energy locally near customers. However, the supplying of power without disturbance is the main challenge for utilities, especially for systems that integrate fluctuating renewable sources which can cause voltage sag and swell. In this paper, voltage sag and swell issues are investigated. The first studied scenario is related to the disturbance of the energy source and the second one is due to the installation of a heavy load with a sensitive load at the same supplying bus. A D-STATCOM is connected at the point of common coupling (pCC) to mitigate the voltage sag and sell problems. An energy storage battery has been installed at the DC-side of the compensator that gives the possibility to control the voltage at the PCC and exchange the active and reactive power with the grid. A linear proportional integral (PI) feed-forward controller supervises the compensator. The obtained results show that the D-STATCOM compensator behaves as a good solution to mitigate the voltage sag and swell in distribution grid.
Permanent Magnet Synchronous Generator-Based Standalone Wind Energy Supply Sy...
In this paper, a novel algorithm, based on dc link voltage, is proposed for effective energy management of a standalone permanent magnet synchronous generator (PMSG)-based variable speed wind energy conversion system consisting of battery, fuel cell, and dump load (i.e., electrolyzer). Moreover, by maintaining the dc link voltage at its reference value, the output ac voltage of the inverter can be kept constant irrespective of variations in the wind speed and load. An effective control technique for the inverter, based on the pulse width modulation (PWM) scheme, has been developed to make the line voltages at the point of common coupling (PCC) balanced when the load is unbalanced. Similarly, a proper control of battery current through dc–dc converter has been carried out to reduce the electrical torque pulsation of the PMSG under an unbalanced load scenario. Based on extensive simulation results using MATLAB/SIMULINK, it has been established that the performance of the controllers both in transient as well as in steady state is quite satisfactory and it can also maintain maximum power point tracking.
Front end buck rectifier with reduced filter size and single-loop control
This paper presents a transformerless solution for front-end rectification, which is particularly suitable for traction applications, requiring high voltages to be stepped down to appropriate dc voltage. The proposed topology is based on pulse widthmodulation buck rectifier (current source inverter topology) and is capable of rectification and stepping down of single-phase ac supply, in a single stage. A new control scheme is proposed to achieve constant dc output voltage and sinusoidal source current, irrespective of large ripples in the dc inductor current. The proposed scheme is configured in single-loop voltage control mode. The relevant small-signal model is derived from the large-signal model using multi order decomposition. An elaborate procedure of dc filter design is discussed, for circuit operation with minimum energy storage. All analytical results are validated by numerical simulation for sinusoidal and distorted source voltage. Experimental verification is achieved through a 1.2-kW grid-connected laboratory prototype.
Irradiance-adaptive PV Module Integrated Converter for High Efficiency and Po...
The strive for efficient and cost-effective photovoltaic systems motivated the power electronic design developed here. The work resulted in a DC-DC converter for module integration and distributed maximum power point tracking (MPPT) with a novel adaptive control scheme. The latter is essential for the combined features of high energy efficiency and high power quality over a wide range of operating conditions. The switching frequency is optimally modulated as a function of solar irradiance for power conversion efficiency maximization. With the rise of irradiance, the frequency is reduced to reach the conversion efficiency target. A search algorithm is developed to determine the optimal switching frequency step. Reducing the switching frequency may, however, compromise MPPT efficiency. Furthermore, it leads to increased ripple content. Therefore, to achieve a uniform high power quality at all conditions, interleaved converter cells are adaptively activated. The overall cost is kept low by selecting components that allow for implementing the functions at low cost. Simulation results show the high value of the module integrated converter for DC standalone and microgrid applications. A 400 W prototype was implemented at 0.14 Euro/W. Testing showed efficiencies above 95% taking into account all losses from power conversion, MPPT, and measurement and control circuitry.
A Sensorless Power Reserve Control Strategy for Two-Stage Grid-Connected PV S...
Due to the still increasing penetration of grid connected Photovoltaic (PV) systems, advanced active power control functionalities have been introduced in grid regulations. A power reserve control, where namely the active power from the PV panels is reserved during operation, is required for grid support. In this paper, a cost-effective solution to realize the power reserve for two-stage grid-connected PV systems is proposed. The proposed solution routinely employs a Maximum Power Point Tracking (MPPT) control to estimate the available PV power and a Constant Power Generation (CPG) control to achieve the power reserve. In this method, the solar irradiance and temperature measurements that have been used in conventional power reserve control schemes to estimate the available PV power are not required, and thereby being a sensorless approach with reduced cost. Experimental tests have been performed on a 3-kW two-stage single-phase grid-connected PV system, where the power reserve control is achieved upon demands.
Maximum power extraction from wind energy system based on fuzzy logic control
This paper proposes a variable speed control scheme for grid-connected wind energy conversion system (WECS) using permanent magnet synchronous generator (PMSG). The control algorithm tracks the maximum power for wind speeds below rated speed of wind turbines and ensures the power will not go over the rated power for wind speeds over the rated value. The control algorithm employs fuzzy logic controller (FLC) to effectively do this target. The wind turbine is connected to the grid via back-to-back PWM-VSC. Two effective computer simulation packages (PSIM and Simulink) are used to carry out the simulation effectively. The control system has two controllers for generator side and grid side converters. The main function of the generator side controller is to track the maximum power through controlling the rotational speed of the wind turbine using FLC. In the grid side converter, active and reactive power control has been achieved by controlling q-axis and d-axis current components, respectively. The d-axis current is set at zero for unity power factor and the q-axis current is controlled to deliver the power flowing from the dc-link to the electric utility grid.
Comparison of Modulation Techniques for Matrix Converter
Matrix Converters can directly convert an ac power supply of fixed voltage into an ac voltage of variable amplitude and frequency. Matrix Converter is a single stage converter. The matrix converters can contribute to the realization of low volume, sinusoidal input current, bidirectional power flow and lack of bulky reactive elements. All the reasons lead to the development of matrix converter. Based on the control techniques used in the matrix converter, the performance varies. So this paper analyses the performance of matrix converter with three different modulation techniques such as PWM, SVPWM and SVM. The basic principle and switching sequence of these modulation techniques are presented in this paper. The output voltage, output current waveforms, voltage transfer ratio and THD spectrum of switching waveforms connected to RL load are analyzed by using Matlab/Simulink software. The simulated results are analyzed and show that the THD is better for SVM technique.
Designing of multilevel dpfc to improve power quality
According to growth of electricity demand and the increased number of non-linear loads in power grids, providing a high quality electrical power should be considered. In this paper, Enhancement of power quality by using fuzzy based multilevel power flow controller (DPFC) is proposed. The DPFC is a new FACTS device, which its structure is similar to unified power flow controller (UPFC). In spite of UPFC, in DPFC the common dc-link between the shunt and series converters is eliminated and three-phase series converter is divided to several single-phase series distributed converters through the line. This eventually enables the DPFC to fully control all power system parameters. It, also, increases the reliability of the device and reduces its cost simultaneously. In recent years multi level inverters are used high power and high voltage applications .Multilevel inverter output voltage produce a staircase output waveform, this waveform look like a sinusoidal waveform leads to reduction in Harmonics. Fuzzy Logic is used for optimal designing of controller parameters. Application of Fuzzy Multilevel DPFC for reduction of Total Harmonic Distortion was presented. The simulation results show the improvement of power quality using DPFC with Fuzzy logic controller.
New ac dc power factor correction architecture suitable for high frequency op...
This paper presents a novel ac-dc power factor correction (PFC) power conversion architecture for single-phase grid interface. The proposed architecture has significant advantages for achieving high efficiency, good power factor, and converter miniaturization, especially in low-to-medium power applications. The architecture enables twice-line-frequency energy to be buffered at high voltage with a large voltage swing, enabling reduction in the energy buffer capacitor size, and elimination of electrolytic capacitors. While this architecture can be beneficial with a variety of converter topologies, it is especially suited for system miniaturization by enabling designs that operate at high frequency (HF, 3 – 30 MHz). Moreover, we introduce circuit implementations that provide efficient operation in this range. The proposed approach is demonstrated for an LED driver converter operating at a (variable) HF switching frequency (3 – 10 MHz) from 120Vac, and supplying a 35Vdc output at up to 30W. The prototype converter achieves high efficiency (92 %) and power factor (0.89), and maintains good performance over a wide load range. Owing to architecture and HF operation, the prototype achieves a high ‘box’ power density of 50W/ in3 (‘displacement’ power density of 130W/ in3), with miniaturized inductors, ceramic energy buffer capacitors, and a small-volume EMI filter.
Hybrid Modulation Concept for Five-Level Active-Neutral-Point-Clamped Converter
In this letter, a hybrid modulation concept consisting of three-level space vector modulation (3L-SVM) and phase-shifted pulse width modulation (PS-PWM) is proposed for five-level active neutral- point-clamped (5L-ANPC) converter. Under this concept, a simpler 3L-SVM plus PS-PWM scheme is applied to realize 5L modulation, instead of using complex 5L-SVM. The control of neutral voltage, flying capacitor voltage, and the improved dc voltage utilization are all implemented. With the help of the proposed concept, well-developed 3L-SVM schemes can be directly applied to the 5L-ANPC converter, which significantly simplify the gating signal generation. This concept can also be applied to other hybrid clamped 5L converters with two dc-link capacitors. It provides a unique solution, which utilize lower level SVM scheme to control higher level multilevel converters.
Power Quality Improvement in Solar Fed Cascaded Multilevel Inverter with Outp...
The presence of harmonics in solar Photo Voltaic (PV) energy conversion system results in deterioration of power quality. To address such issue, this paper aims to investigate the elimination of harmonics in a solar fed cascaded fifteen level inverter with aid of Proportional Integral (PI), Artificial Neural Network (ANN) and Fuzzy Logic (FL) based controllers. Unlike other techniques, the proposed FLC based approach helps in obtaining reduced harmonic distortions that intend to an enhancement in power quality. In addition to the power quality improvement, this paper also proposed to provide output voltage regulation in terms of maintaining voltage and frequency at the inverter output end in compatible with the grid connection requirements. The simulations are performed in the MATLAB / Simulink environment for solar fed cascaded 15 level inverter incorporating PI, ANN and FL based controllers. To exhibit the proposed technique, a 3 kWp photovoltaic plant coupled to multilevel inverter is designed and hardware is demonstrated. All the three techniques are experimentally investigated with the measurement of power quality metrics along with establishing output voltage regulation.
What's hot (20)
Development of wind and solar based ac microgrid with power quality improveme...
Development of wind and solar based ac microgrid with power quality improveme...
Statcom for improved dynamic performance of wind farms in power grid
Statcom for improved dynamic performance of wind farms in power grid
Power Quality Assessment of Voltage Positive Feedback Based Islanding Detecti...
Power Quality Assessment of Voltage Positive Feedback Based Islanding Detecti...
A New Circuit of Modular Multilevel Inverter for Grid-Connected Photovoltaic ...
A New Circuit of Modular Multilevel Inverter for Grid-Connected Photovoltaic ...
Single-Stage Switched-Capacitor Module (S3CM) Topology for Cascaded Multileve...
Single-Stage Switched-Capacitor Module (S3CM) Topology for Cascaded Multileve...
Novel High Performance Stand Alone Solar PV System with High Gain, High Effic...
Novel High Performance Stand Alone Solar PV System with High Gain, High Effic...
Improving the Dynamic Performance of Wind Farms with STATCOM
Improving the Dynamic Performance of Wind Farms with STATCOM
Design and Control of Wind integrated Shunt Active Power Filter to Improve Po...
Design and Control of Wind integrated Shunt Active Power Filter to Improve Po...
Mppt with single dc–dc converter and inverter for grid connected hybrid wind-...
Mppt with single dc–dc converter and inverter for grid connected hybrid wind-...
Voltage Sag and Swell Mitigation Using DSTATCOM in Renewable Energy Based Dis...
Voltage Sag and Swell Mitigation Using DSTATCOM in Renewable Energy Based Dis...
Permanent Magnet Synchronous Generator-Based Standalone Wind Energy Supply Sy...
Permanent Magnet Synchronous Generator-Based Standalone Wind Energy Supply Sy...
Front end buck rectifier with reduced filter size and single-loop control
Front end buck rectifier with reduced filter size and single-loop control
Irradiance-adaptive PV Module Integrated Converter for High Efficiency and Po...
Irradiance-adaptive PV Module Integrated Converter for High Efficiency and Po...
A Sensorless Power Reserve Control Strategy for Two-Stage Grid-Connected PV S...
A Sensorless Power Reserve Control Strategy for Two-Stage Grid-Connected PV S...
Maximum power extraction from wind energy system based on fuzzy logic control
Maximum power extraction from wind energy system based on fuzzy logic control
Comparison of Modulation Techniques for Matrix Converter
Comparison of Modulation Techniques for Matrix Converter
Designing of multilevel dpfc to improve power quality
Designing of multilevel dpfc to improve power quality
New ac dc power factor correction architecture suitable for high frequency op...
New ac dc power factor correction architecture suitable for high frequency op...
Hybrid Modulation Concept for Five-Level Active-Neutral-Point-Clamped Converter
Hybrid Modulation Concept for Five-Level Active-Neutral-Point-Clamped Converter
Power Quality Improvement in Solar Fed Cascaded Multilevel Inverter with Outp...
Power Quality Improvement in Solar Fed Cascaded Multilevel Inverter with Outp...
Similar to Power quality improvement in distribution network using DSTATCOM with battery energy storage system
High frequency ac-link pv inverter
In this paper, a high-frequency ac-link photovoltaic (PV) inverter is proposed. The proposed inverter overcomes most of the problems associated with currently available PV inverters. In this inverter, a single-stage power-conversion unit fulfills all the system requirements, i.e., inverting dc voltage to proper ac, stepping up or down the input voltage, maximum power point tracking, generating low-harmonic ac at the output, and input/output isolation. This inverter is, in fact, a partial resonant ac-link converter in which the link is formed by a parallel inductor/capacitor (LC) pair having alternating current and voltage. Among the significant merits of the proposed inverter are the zero-voltage turn-on and soft turn-off of the switches which result in negligible switching losses and minimum voltage stress on the switches. Hence, the frequency of the link can be as high as permitted by the switches and the processor. The high frequency of operation makes the proposed inverter very compact. The other significant advantage of the proposed inverter is that no bulky electrolytic capacitor exists at the link. Electrolytic capacitors are cited as the most unreliable component in PV inverters, and they are responsible for most of the inverters’ failures, particularly at high temperature. Therefore, substituting dc electrolytic capacitors with ac LC pairs will significantly increase the reliability of PV inverters. A 30-kW prototype was fabricated and tested. The principle of operation and detailed design procedure of the proposed inverter along with the simulation and experimental results are included in this paper. To evaluate the long-term performance of the proposed inverter, three of these inverters were installed at three different commercial facilities in Texas, USA, to support the PV systems. These inverters have been working for several months now.
Critical Current Control (C3) and Modeling of a Buck Based LED Driver with Po...
Buck converter has a good aptitude for LED driver application. Here a new technique introduced to control and model a buck converter in the closed loop condition using Lagrange equation. To improve the final model accuracy, parasitic elements of the converter are taken into account. The main advantage of this method is its novelty and simple implementation. Also, the converter power factor has improved under critical current control (C3) technique. Frequency response and step response of the small signal model are derived and analysed. The theoretical predictions are tested and validated by means of PSIM software. Finally, precise agreement between the proposed model and the simulation results has obtained.
Single- and Two-Stage Inverter-Based Grid-Connected Photovoltaic Power Plants...
Grid-connected distributed generation sources interfaced with voltage source inverters (VSIs) need to be disconnected from the grid under: 1) excessive dc-link voltage; 2) excessive ac currents; and 3) loss of grid-voltage synchronization. In this paper, the control of single- and two-stage grid-connected VSIs in photovoltaic (PV) power plants is developed to address the issue of inverter disconnecting under various grid faults. Inverter control incorporates reactive power support in the case of voltage sags based on the grid codes’ (GCs) requirements to ride-through the faults and support the grid voltages. A case study of a 1-MW system simulated in MATLAB/Simulink software is used to illustrate the proposed control. Problems that may occur during grid faults along with associated remedies are discussed. The results presented illustrate the capability of the system to ride-through different types of grid faults.
Modeling and simulation of a distribution statcom (d statcom) for power quali...
This paper presents the systematic procedure of the modeling and simulation of a Distribution STATCOM (DSTATCOM) for power quality problems, voltage sag and swell based on Sinusoidal Pulse Width Modulation (SPWM) technique. Power quality is an occurrence manifested as a nonstandard voltage, current or frequency that results in a failure of end use equipments. The major problems dealt here is the voltage sag and swell. To solve this problem, custom power devices are used. One of those devices is the Distribution STATCOM (D-STATCOM), which is the most efficient and effective modern custom power device used in power distribution networks. D-STATCOM injects a current in to the system to correct the voltage sag and swell.The control of the Voltage Source Converter (VSC) is done with the help of SPWM. The proposed D-STATCOM is modeled and simulated using MATLAB/SIMULINK software.
Coordination control of hybrid ac dc microgrid
The hybrid AC/DC microgrid is considered to be the more and more popular in power systems as increasing DC loads. In this study, it is presented that a hybrid AC/DC microgrid is modelled with some renewable energy sources (e.g. solar energy, wind energy), typical storage facilities (e.g. batteries), and AC, DC load, and also the power could be transformed smoothly between the AC and DC sub-grids by the bidirectional AC/DC converter. Meanwhile, coordination control strategies are proposed for power balance under various operations. In grid-connected mode, the U–Q (DC bus voltage and reactive) or PQ method is adopted for the bidirectional AC/DC converter according to the amount of exchange power between AC and DC system in order to improve the DG utilisation efficiency, protecting the converter and maintain the stable operation of the system. In islanded mode, V/F control is applied to stabilising the entire system voltage and frequency, achieving the power balance between the AC and DC systems. Finally, these control strategies are verified by simulation with the results showing that the control scheme would maintain stable operation of the hybrid AC/DC microgrid.
Designing of Multilevel DPFC to Improve Power Quality
According to growth of electricity demand and the increased number of non-linear loads in power grids, providing a high quality electrical power should be considered. In this paper, Enhancement of power quality by using fuzzy based multilevel power flow controller (DPFC) is proposed. The DPFC is a new FACTS device, which its structure is similar to unified power flow controller (UPFC). In spite of UPFC, in DPFC the common dc-link between the shunt and series converters is eliminated and three-phase series converter is divided to several single-phase series distributed converters through the line. This eventually enables the DPFC to fully control all power system parameters. It, also, increases the reliability of the device and reduces its cost simultaneously. In recent years multi level inverters are used high power and high voltage applications .Multilevel inverter output voltage produce a staircase output waveform, this waveform look like a sinusoidal waveform leads to reduction in Harmonics. Fuzzy Logic is used for optimal designing of controller parameters. Application of Fuzzy Multilevel DPFC for reduction of Total Harmonic Distortion was presented. The simulation results show the improvement of power quality using DPFC with Fuzzy logic controller.
Reduced Sensor Based PV Array Fed Direct Torque Control Induction Motor Drive...
This paper aims at the design, control and implementation of a solar photovoltaic (PV) array fed speed sensorless direct torque control (DTC) of an induction motor drive (IMD) for water pumping in standalone as well as battery connected hybrid mode. This stator flux estimated by proposed flux observer, is used for speed estimation. A DC link current sensor is used to reconstruct the motor phase currents by modified active voltage vector. One voltage sensor for DC link voltage sensing and only one current sensor for DC link current sensing, are used in this system for standalone operation of the system. All other required quantities are estimated through these two sensed signals. The IMD is energized by a photovoltaic (PV) array, which is operated at maximum power point (MPP). A perturb and observe control algorithm with additional flow rate controller, is proposed for MPP, which tracks MPP throughout the operating range and provides the facility to control flow rate. The suitability of the system is judged through simulated results in MATLAB/Simulink as well as test results obtained on a prototype developed in the laboratory.
Power Management in PV-Battery-Hydro Based Standalone Microgrid
This paper proposes a high-efficiency two stage three-level grid-connected photovoltaic inverter. This work deals with the frequency regulation, voltage regulation, power management and load levelling of solar photovoltaic (PV)-battery-hydro based microgrid (MG). In this MG, the battery capacity is reduced as compared to a system, where the battery is directly connected to the DC bus of the voltage source converter (VSC). A bidirectional DC–DC converter connects the battery to the DC bus and it controls the charging and discharging current of the battery. It also regulates the DC bus voltage of VSC, frequency and voltage of MG. The proposed system manages the power flow of different sources like hydro and solar PV array. However, the load levelling is managed through the battery. The battery with VSC absorbs the sudden load changes, resulting in rapid regulation of DC link voltage, frequency and voltage of MG. Therefore, the system voltage and frequency regulation allows the active power balance along with the auxiliary services such as reactive power support, source current harmonics mitigation and voltage harmonics reduction at the point of common interconnection. The experimental results under various steady state and dynamic conditions, exhibit the excellent performance of the proposed system and validate the design and control of proposed MG.
Construction and performance investigation of three phase solar pv and batter...
This study examines the use of Unified Power Quality Conditioner (UPQC) to mitigate the power quality problems existed in the grid and the harmonics penetrated by the non-linear loads. The UPQC is supported by the Photovoltaic (PV) and Battery Energy Storage System (BESS) in this work. Generally, the PV system supplies the active power to the load. However, if the PV is unable to supply the power then the BESS activates and provides power especially during the longer-term voltage interruption. The standalone PV-UPQC system is less reliable compared to a hybrid PV-BESS system because of its instability and high environment-dependency. Therefore, BESS will improve the voltage support capability continuously in the longer-term, reduce the complexity of the DC-link voltage regulation algorithm, and keep producing clean energy.
A Unified Control Strategy for Three-phase Inverter in Distributed Generation
This paper presents a unified control strategy that enables both islanded and grid-tied operation of three-phase inverter in distributed generation (DG), with no need for switching between two corresponding controllers or critical islanding detection. The proposed control strategy composes of an inner inductor current loop, and a novel voltage loop in the synchronous reference frame (SRF). The inverter is regulated as a current source just by the inner inductor current loop in grid-tied operation, and the voltage controller is automatically activated to regulate the load voltage upon the occurrence of islanding. Furthermore, the waveforms of the grid current in grid-tied mode and the load voltage in islanding mode are distorted under nonlinear local load with the conventional strategy. And this issue is addressed by proposing a unified load current feed forward in the paper. Additionally, the paper presents the detailed analysis and the parameter design of the control strategy. Finally, the effectiveness of the proposed control strategy is validated by the simulation and experimental results.
Hybrid topology of asymmetric cascaded multilevel inverter with renewable ene...
This paper presents a binary topology of Multimodule level inverters produce a staircase output voltage from renewable DC voltage sources. The MLI (Multi Level Inverter) Requires many number of semiconductor switches is main drawback of multilevel inverters. The MLI can be classified as two method, one is symmetric and another asymmetric converters. In symmetrical multilevel inverter can apply same voltage level to all cascaded circuit, in asymmetric multilevel inverters can be vary input source voltage at each cascaded H-bridge by using binary algorithm. In this paper, a discrete binary topology for multilevel converters is proposed using cascaded sub-multilevel Cells. This sub-multilevel converter can produce sixty three levels of voltage from five discrete DC source. The Total Harmonic Distortions (THD) is minimized by discrete binary topology. The working operation and performance of the proposed multilevel inverters studies has been verified by simulation of using SIMULINK / MA TLAB results.
Power quality improvement in utility interactive based ac dc converter using ...
This paper highlights the power quality issues and explains the remedial measures taken by means of hybrid front-end third harmonic current injection rectifiers. Here zig-zag transformer is used as the current injection device so that the advantages pertaining to the zig-zag transformer is effectively utilized. The third harmonic current injection device along with three-level boost converter at the output stage will increase the DC-link voltage. With less boost inductance, generally half of the conventional boost converter inductance is sufficient to implement the proposed converter structure resulting in reduced ripple current and also the device rating is reduced by half of the output voltage. Moreover, the power quality is well improved using third harmonic current modulated front-end structure which is well appropriate for medium/higher power applications. The experimental prototype of hybrid front-end converter is developed in the laboratory to validate the MATLAB simulation results.
Control of a Three-Phase Hybrid Converter for a PV Charging Station
Hybrid boost converter (HBC) has been proposed to replace a dc/dc boost converter and a dc/ac converter to reduce conversion stages and switching loss. In this paper, control of a three-phase HBC in a PV charging station is designed and tested. This HBC interfaces a PV system, a dc system with hybrid plugin electrical vehicles (HPEVs) and a three-phase ac grid. The control of the HBC is designed to realize maximum power point tracking (MPPT) for PV, dc bus voltage regulation, and ac voltage or reactive power regulation. A test bed with power electronics switching details is built in MATLAB/SimPowersystems for validation. Simulation results demonstrate the feasibility of the designed control architecture. Finally, lab experimental testing is conducted to demonstrate HBC’s control performance.
A Novel Design of PI Current Controller for PMSG-based Wind Turbine Consideri...
This paper presents a novel design process of decoupled PI current controller for permanent magnet synchronous generator (PMSG)-based wind turbines feeding a grid-tied inverter through back-to-back converter. Specifically, the design methodology consists of combining disturbance observer-based control (DOBC) with feedback linearization (FBL) technique to ensure nominal transient performance recovery under model uncertainty. By simplifying the DOBC under the feedback linearizing control, it is shown that the composite controller reduces to a decoupled PI current controller plus an additional term that has the main role of recovering the nominal transient performance of the feedback linearization, especially under step changes in the reference. Additionally, an anti windup compensator arises naturally into the controller when considering the control input saturation to design the DOBC. This permits to remove the effect of the saturation blocks required to limit the control input. The proposed control scheme is implemented and validated through experimentation conducted on 22-pole, 5 kW PMSG. The results revealed that the proposed technique can successfully achieve nominal performance recovery under model uncertainty as well as improved transient performances under control saturation.
Control for Grid-Connected and Intentional Islanding Operations of Distribute...
Intentional islanding describes the condition in which a microgrid or a portion of the power grid,
which consists of a load and a distributed generation (DG) system, is isolated from the remainder
of the utility system. In this situation, it is important for the microgrid to continue to provide
adequate power to the load. Under normal operation, each DG inverter system in the microgrid
usually works in constant current control mode in order to provide a preset power to the main
grid. When the microgrid is cut off from the main grid, each DG inverter system must detect this
islanding situation and must switch to a voltage control mode. In this mode, the microgrid will
provide a constant voltage to the local load. This paper describes a control strategy that is used to
implement grid-connected and intentional-islanding operations of distributed power generation.
This paper proposes an intelligent load-shedding algorithm for intentional islanding and an
algorithm of synchronization for grid reconnection.
Similar to Power quality improvement in distribution network using DSTATCOM with battery energy storage system (19)
Micro Wind Power Generator with Battery Energy Storage for Critical Load
Micro Wind Power Generator with Battery Energy Storage for Critical Load
Dynamic behavior of DFIG wind turbine under grid fault conditions (1)
Dynamic behavior of DFIG wind turbine under grid fault conditions (1)
Critical Current Control (C3) and Modeling of a Buck Based LED Driver with Po...
Critical Current Control (C3) and Modeling of a Buck Based LED Driver with Po...
Single- and Two-Stage Inverter-Based Grid-Connected Photovoltaic Power Plants...
Single- and Two-Stage Inverter-Based Grid-Connected Photovoltaic Power Plants...
Modeling and simulation of a distribution statcom (d statcom) for power quali...
Modeling and simulation of a distribution statcom (d statcom) for power quali...
Designing of Multilevel DPFC to Improve Power Quality
Designing of Multilevel DPFC to Improve Power Quality
Reduced Sensor Based PV Array Fed Direct Torque Control Induction Motor Drive...
Reduced Sensor Based PV Array Fed Direct Torque Control Induction Motor Drive...
Power Management in PV-Battery-Hydro Based Standalone Microgrid
Power Management in PV-Battery-Hydro Based Standalone Microgrid
Construction and performance investigation of three phase solar pv and batter...
Construction and performance investigation of three phase solar pv and batter...
A Unified Control Strategy for Three-phase Inverter in Distributed Generation
A Unified Control Strategy for Three-phase Inverter in Distributed Generation
Hybrid topology of asymmetric cascaded multilevel inverter with renewable ene...
Hybrid topology of asymmetric cascaded multilevel inverter with renewable ene...
Power quality improvement in utility interactive based ac dc converter using ...
Power quality improvement in utility interactive based ac dc converter using ...
Control of a Three-Phase Hybrid Converter for a PV Charging Station
Control of a Three-Phase Hybrid Converter for a PV Charging Station
A Novel Design of PI Current Controller for PMSG-based Wind Turbine Consideri...
A Novel Design of PI Current Controller for PMSG-based Wind Turbine Consideri...
Control for Grid-Connected and Intentional Islanding Operations of Distribute...
Control for Grid-Connected and Intentional Islanding Operations of Distribute...
More from Asoka Technologies
Solar pv charging station for electric vehicles
Of late, electric vehicles (EVs) have attracted much attention owing to their use of clean energy. Large progress in lithium-ion battery has propelled the development of EVs.However, the challenge is that growing number of EVs leads to huge demand in electric power, which will aggravate the power grid load. This leads to an exploration for alternative and clean sources of energy to charge EVs. This project implements solar energy system to erect a charging station for EV application. The charging station employs multi-port charging by providing a constant voltage DC bus. The charging controllers are operated based on the concept of power balance, and constant current/constant voltage charging. Performance of the charging system is validated with simulation and experimental results.
Generation of Higher Number of Voltage Levels by Stacking Inverters of Lower ...
This paper proposes a new method of generating higher number of levels in the voltage waveform by stacking multilevel converters with lower voltage space vector structures. An important feature of this stacked structure is the use of low voltage devices while attaining higher number of levels. This will find extensive applications in electric vehicles since direct battery drive is possible. The voltages of all the capacitors in the structure can be controlled within a switching cycle using the switching state redundancies (pole voltage redundancies). This helps in reducing the capacitor size. Also, the capacitor voltages can be balanced irrespective of modulation index and load power factor. To verify the concept experimentally, a 9-level inverter is developed by stacking two 5-level inverters and an induction motor is run using V/f control scheme. Both steady state and transient results are presented.
Novel symmetric modular hybrid multilevel inverter with reduced number of sem...
In this paper, by using a modular hybrid structure, a new topology for symmetric multilevel inverters (MLI) with a small number of semiconductors and low voltage stress across switches is proposed. Despite many other topologies, this topology can inherently produce negative levels and zero levels without using the H-bridge. The voltage stress across a particular switch of the proposed MLI is inversely proportional to the number of the switching of that switch in a voltage period. The proposed structure is based on two types of module, that is, the f-module and the e-module. The e-module uses a capacitive voltage divider to double the number of non-zero levels. The voltages of the capacitors are approximately balanced without complex control methods. The basic structure of the proposed topology is formed by connecting the f-module and the e-module in series with each other, and the cascaded topology is developed by cascading multiple f-modules with an e-module. To investigate the proposed topology and proving its practicability, simulation results with MATLAB/Simulink, investigation of the capacitor voltages, loss calculations and experimental results are presented. A comparative study is also performed to show the merit of the new multilevel inverter over other topologies.
A Variable DC Link based Novel Multilevel Inverter Topology for Low Voltage A...
In this paper; a variable dc link based novel multilevel inverter (MLI) topology is proposed. This proposed topology comprises two variable dc links and a modified H-bridge unit. This new single-phase topology offers advantages such as reduction in count of switches; gate drivers and dc sources while simultaneously improving the power quality. The proposed topology has been analyzed for both symmetric and asymmetric modes of operation. A comparative study of the proposed topology with some recent MLI topologies has been presented. The comparative study indicates that the proposed topology requires less number of dc sources; switches and driver circuits as compared to other topologies. The proposed topology has been simulated for 31- level asymmetric configuration in MATLAB/SIMULINK environment to verify the proper operation of proposed topology. Harmonic analysis was also performed for 31-level inverter which showed significant reduction in the total harmonic distortion (THD) for phase voltage and current waveforms. The proposed topology is suitable for low voltage applications such as standalone photovoltaic (PV) systems and hybrid electric vehicles (HEVs).
A Simplified Space Vector Pulse-Width Modulation Scheme for Three-Phase Casca...
A simplified space vector pulse-width modulation (SVPWM) for three-phase cascaded H-bridge (CHB) inverters is presented in this paper. Treating each unit as a three-level inverter and adopting serial calculation mode, a CHB inverter is modulated unit by unit using three-level SVPWM. Duty cycles of real sector are obtained by mapping duty cycles of sector 1, in which the calculation of three-level SVPWM is done. The process to implement multilevel SVPWM is simplified to the process to implement three-level SVPWM. By reusing FPGA chip resource which is used for the calculation of three-level SVPWM, the presented SVPWM can be easily adopted to a CHB inverter with different number of units, while the FPGA chip resource utilization is reduced significantly. In addition, the presented SVPWM provides an effective switching frequency higher than the switching frequency of IGBTs. Simulation and experimental results are provided to verify the feasibility of the presented SVPWM.
A New Family of Step-up Hybrid Switched- Capacitor Integrated Multilevel Inve...
In the low voltage based renewable systems like PV and Fuel cell applications, the step-up of the output voltage to drive the loads is essential. For this, the integration of switched-capacitor (SC) units with the dc-ac converters will have the potential advantages like improved efficiency, optimal switching devices, small size of passive elements (L and C) as compared with traditional two-stage conversion system (dc/dc converter and dc/ac converter). This paper focuses on a new family of step-up multilevel inverter topologies with switched capacitor integration with dual input voltage sources. With the flexibility of 2 dc sources and switching capacitor circuits, four different topologies have been suggested in this paper with features of high voltage gain, reduced component count, reduced voltage stress and self-voltage balancing of the capacitor while achieving a higher number of levels. A detailed analysis of proposed multilevel inverters has been analyzed with the symmetrical and asymmetrical mode of operations and the associated gain, the number of levels, and other performance indices are presented. An in-depth study of all the topologies has been accomplished in this paper with several comparative studies in terms of components count, voltage gain and cost. The effectiveness and practicability of the suggested topology with 13 level output voltage has been explained by the experimental results obtained from a scale down prototype.
A multi cell 21-level hybrid multilevel inverter synthesizes a reduced number...
A multi-cell hybrid 21-Level multilevel inverter is proposed in this paper. The proposed topology includes two-unit; an H-bridge is cascaded with a modified K-type unit to generate an output voltage waveform with 21 levels based only on two unequal DC suppliers. The proposed topology's advantage lies in the fine and clear output voltage waveforms with high output efficiency. Meanwhile, the high number of output voltage waveform levels generates a low level of distortion and reduces the level of an electromagnetic interface (EMI). Moreover, it reduces the voltage stress on the switching devices and gives it a long lifetime. Also, the reduction in the number of components has a noticeable role in saving size and cost. Regarding the capacitors charging, the proposed topology presents an online method for charging and balancing the capacitor's voltage without any auxiliary circuits. The proposed topology can upgrade to a high number of output steps through the cascading connection. Undoubtedly this cascading will increase the power level to medium and high levels and reduce the harmonics content to a neglectable rate. The proposed system has been tested through the simulation results, and an experimental prototype based on the controller dSPACE (DS-1103) hardware unit used to support the simulation results.
A generalized multilevel inverter topology with reduction of total standing v...
This paper presents a new multilevel inverter topology with reduced active switches and total standing voltage. The proposed topology can generate a high number of voltage levels in the symmetric configuration. This topology intuitively generates positive and negative cycles without an additional H-bridge unit, which considerably reduces the total standing voltage of the inverter. A cascaded structure is developed from the proposed topology to create higher voltage levels. To show the novelty of the proposed topology, a thorough comparison between the available and the proposed topologies in terms of the number of switches, standing voltages, and dc-sources is presented. Furthermore, the power loss analysis is carried out for various load values. The feasibility of the proposed nine-level inverter is verified with simulation and experimental results.
Residential Community Load Management based on Optimal Design of Standalone H...
Microgrids being an important entity in the distribution system, and to get their full advantages
by incorporating maximum distributed generation, standalone hybrid renewable energy systems (HRESs), being environmentally-safe and economically-efficient, are considered as the promising solution to electrify remote areas where the grid power is not available. In this work, a techno-economic investigation with an optimal design of HRES is presented to fulfill the domestic electricity need for a residential area of the Sherani district in the Province of Baluchistan, Pakistan. Nine case studies based on PV/wind/diesel/battery are analyzed based on net present cost (NPC), cost of energy (COE), and emission to decide the feasible solution. HOMER tool is utilized to accomplish modeling and simulation for economic analysis and optimal sizing. Simulation results demonstrated that HRES with PV-wind-battery is the most viable option for the specified area, and the optimal sizing of components are also obtained with $ 28,620 NPC and 0.311 $/kWh COE which shows 81.65% reduction in cost and 100% preserving in toxic emission while fulfilling 100% energy demand with 67.3% of excess energy. Furthermore, MATLAB/Simulink modeling for the optimally designed system is built for technical analysis while its effectiveness is proved by keeping dc and ac buses voltage constant, safe operating range of battery state of charge (SOC) with active power balance between HRES components, as well as efficient ac voltage quality, regardless of generation disturbances and load fluctuations. The output signal has total harmonic distortion (THD) of 0.30% as compared to 5.44% with the conventional control scheme. The novelty lies in the sequential application of both HOMER and MATLAB simulations of the proposed HRES model and validation of the proposition for the studied area; by using and implementing model predictive control (MPC) of a reconfigurable inverter.
Reliability evaluation of MPPT based interleaved boost converter for PV system
The demand for power supply and depletion of the conventional energy sources are increasing drastically. So to overcome this problem, the best alternative power generation for conventional fossil fuel is Photovoltaic solar cell based system because of its advantage of pollution free and its availability in abundance with free of cost. In the MPPT based PV system the converters are the most sensitive part. Therefore to provide uninterrupted power supply without compromising the quality of power, reliability evaluation of interleaved boost converter becomes necessary. MATLAB/Simulink is used for the simulation studies and to determine the power losses of various components of the converter which is used in calculating the failure rates and reliability of the interleaved boost converter. Reliability studies of IBC have not been studied much. However there exists few literature in which reliability expression has been developed using Markov technique which is a more complex method as compare to Reliability Block Diagram (RBD). Therefore this paper proposes reliability modeling and reliability evaluation of Interleaved boost converter in MPPT based photo-voltaic system by using simple RBD method.
Power Quality Improvement of Grid-Connected Photovoltaic Systems Using Trans-...
Voltage-source inverter has been used widely in traditional photovoltaic systems which have limitations. To overcome, Z-source inverter has been introduced. In spite of all the features introduced in Z-source inverter, its configuration has been improved over the years, like trans-Z-source inverter which has added advantages compared to traditional inverters, namely buck–boost feature, lesser passive elements, and higher voltage boost gain. In this paper, photovoltaic arrays are connected to the grid via the trans-Z-source inverter with the aim of improving its power quality. Moreover, the shoot through duty ratio is kept constant in the switching control method to add features like lower voltage stress (higher reliability), lower total harmonic distortion (lower maintenance cost), and higher voltage boost ratio. To evaluate the precision of the proposed system, the photovoltaic system is simulated on a standard grid and under partial shading condition which brings about voltage sag, and hence, a dynamic voltage restorer is used to mitigate voltage sag. Simulation results are presented to verify the validation of the proposed photovoltaic system in terms of voltage and current THD reducing 78.2% and 19.7%, respectively.
Power optimisation scheme of induction motor using FLC for electric vehicle
In electric vehicles (EVs) and hybrid EVs, energy efficiency is essential where the energy storage is limited. Adding to its high stability and low cost, the induction motor efficiency improves with loss minimisation. Also, it can consume more power than the actual need to perform its working when it is operating in less than full load condition. This study proposes a control strategy based on the fuzzy logic control (FLC) for EV applications. FLC controller can improve the starting current amplitude and saves more power. Through the MATLAB/SIMULINK software package, the performance of this control was verified through simulation. As compared with the conventional proportional integral derivative controller, the simulation schemes show good, high-performance results in time-domain response and rapid rejection of system-affected disturbance. Therefore, the core losses of the induction motor are greatly reduced, and in this way improves the efficiency of the driving system. Finally, the suggested control system is validated by the experimental results obtained in the authors’ laboratory, which are in good agreement with the simulation results.
Power Flow Control of Interconnected AC-DC Microgrids in Grid-Connected Hybri...
This paper introduces a new approach for power flow control of interconnected AC-DC microgrids in grid-connected hybrid microgrids based on implementing a modified unified interphase power controller (UIPC). A typical grid-connected hybrid microgrid including one AC microgrid and one DC microgrid is considered as studied system. Instead of using the parallel-connected power converters, these microgrids are interconnected using a modified UIPC. As the first contribution of this paper, the conventional structure of UIPC, which uses three power converters in each phase, is modified so that a reduced number of power converters is implemented for power exchange control between AC-DC microgrids. The modified structure includes one power converter in each phase, named as line power converter (LPC), and a power converter which regulates the DC bus voltage, named as bus power converter (BPC) here. The AC microgrid is connected to the main grid through the LPCs which their DC buses are linked and can operate in capacitance mode (CM) or inductance mode (IM). A fuzzy logic controller is used in the control structure of the LPCs. The fuzzy inference system is optimized based on H∞ filtering method to reduce the errors in membership functions design. Through the BPC, the DC voltage of LPCs is supplied by the DC microgrid. However, since the DC microgrid voltage is provided here by a PV system, the DC link voltage of the LPCs is fluctuating. Thus, as the second contribution, to stabilize the DC link fluctuations, a new nonlinear disturbance observer based robust multiple-surface sliding mode control (NDO-MS-SMC) strategy is presented for DC side control of the BPC. The simulation results confirm the effectiveness of the proposed power flow control strategy of the improved UIPC for hybrid microgrids.
Power flow control of hybrid micro grids using modified uipc
Neuro Fuzzy Inference System (ANFIS) controlled modified Unified Inter-Phase Power Controller (UIPC). For study, a classic hybrid micro-grid connected to grid comprising of a AC micro-grid and a DC micro-grid is taken into account. These micro-grids are interconnected employing a modified UIPC, rather than using the power converters connected in parallel. As the first input of this paper is the standard structure of UIPC, which used three power converters in every phase. It was then modified such as number of power converters is used less and implemented for the control of the exchange of power between AC-DC microgrids. In every phase there is one power electronic converter in the improved structure. It is called as Line Power Converter (LPC). Also there is Bus Power Converter (BPC) to regulate the voltage of the DC bus. The Line Power Converters links the AC micro-grid to the main grid. The DC buses are also linked with them. It can be operated in Inductance Mode (IM) as well as Capacitance Mode (CM). The control structure of LPCs has an Adaptive Fuzzy Logic Controller in it. For hybrid micro-grids, the capability of the suggested power flow control strategy is confirmed by the MATLAB simulation results.
Multifunctional grid tied pv system using modified klms control
This paper deals with the modified kernel least mean square (KLMS) control strategy in double-stage, solar photovoltaic (PV) grid tied system to enhance the power quality at common coupling point (CCP). This proposed control algorithm has less oscillations, fast convergence, fast dynamic response and good steady state performance. A control strategy is used to extract the fundamental active current component of load and generates reference grid current for a DC-AC converter. The proposed modified KLMS control mitigates multiple power quality concerns such as harmonics reduction, unity power factor and load balancing. The dynamic performance of proposed system is confirmed into the MATLAB\Simulink environment. Test results on hardware implementation are presented at varying solar irradiation levels and load unbalancing. Test results are found satisfactory and total harmonic distortion (THD) of the grid currents are observed well within the IEEE-519 standard.
Modelling and voltage control of the solar wind hybrid micro-grid with optimi...
Electricity generation from the wind and solar photovoltaic (PV) systems are highly dependent upon weather conditions. Their intermittent nature leads to fluctuations in their output. Therefore, the need for rapid compensation for energy transmission and distribution systems is increasingly important. Static Synchronous Compensator (STATCOM) can be adopted for reactive power compensation and for decreasing the voltage fluctuation caused by the system and renewable energy sources. This study presents modelling of a Solar PV-Wind Hybrid Micro-grid and the increase of the stable operating limit of the system in case of the incorporation of STATCOM is examined. The major contribution of this paper is the optimization of gain parameters of four PI controllers in STATCOM control circuit based on genetic algorithms (GA) and Bacteria Foraging Algorithm (BFA) and therefore obtaining better responses and voltage stability in terms of nonlinear nature of solar-wind hybrid micro-grid. The Simulink models of the system architecture include a wind turbine model, a solar PV power system model and a STATCOM. It is certified that the voltage fluctuation at the end of the bus bar is reduced by 8% using conventional PI controller, by 10% for GA-based PI controller, and by 15% for BFA based PI controller under variable load. The results obtained by GA and BFA-based optimization of PI controllers are compared with that of the conventional controller and better results attained.
Intelligent Power Sharing of DC Isolated Microgrid Based on Fuzzy Sliding Mod...
Linear droop control can realize power sharing among generators in DC microgrid without relying on critical communication links. However, the droop relationship between output power and voltage magnitude of renewable power generate system is nonlinear with uncertainties and disturbances from renewable sources and loads in practical DC microgrid. A novel droop scheme is proposed for an isolated DC microgrid to solve the nonlinear problem. The control strategy is proposed by using the Takagi-Sugeno (T-S) fuzzy model and sliding mode algorithm. The nonlinear droop characteristics can be represented by T-S model through taking advantage of locally measured output variables. The sliding mode droop controller is designed for compensating the uncertainties and disturbances to derive accurate power sharing based on T-S fuzzy model. The proposed scheme is proved to be effective under variable operating conditions through PSIM/Matlab simulation.
Implementation of solar pv battery and diesel generator based electric vehic...
In this paper, a solar PV (Photovoltaic) array, a battery energy storage (BES), a diesel generator (DG) set and grid based EV charging station (CS) is utilized to provide the incessant charging in islanded, grid connected and DG set connected modes. The charging station is primarily designed to use the solar photovoltaic PV array and a BES to charge the electric vehicle (EV) battery. However, in case of exhausted storage battery and unavailable solar PV array generation, the charging station intelligently takes power from the grid or DG (Diesel Generator) set. However, the power from DG set is drawn in a manner that, it always operates at 80-85% loading to achieve maximum fuel efficiency under all loading conditions. Moreover, in coordination with the storage battery, the charging station regulates the generator voltage and frequency without a mechanical speed governor. It also ensures that the power drawn from the grid or the DG set is at unity power factor (UPF) even at nonlinear loading. Moreover, the PCC (Point of Common Coupling) voltage is synchronized to the grid/ generator voltage to obtain the ceaseless charging. The charging station also performs the vehicle to grid active/reactive power transfer, vehicle to home and vehicle to vehicle power transfer for increasing the operational efficiency of the charging station. The operation of the charging station is experimentally validated using the prototype developed in the laboratory.
High step up quasi-z source dc-dc converter
In this paper, a high step-up Quasi-Z Source (QZS) DC-DC converter is proposed. This converter uses a hybrid switched-capacitors switched-inductor method in order to achieve high voltage gains. The proposed converter have resolved the voltage gain limitation of the basic QZS DC-DC converter while keeping its main advantages such as continuous input current and low voltage stress on capacitors. Compared to the basic converter, the duty cycle is not limited, and the voltage stress on the diodes and switch isn’t increased. In addition to these features, the proposed converter has a flexible structure, and extra stages could be added to it in order to achieve even higher voltage gains without increasing the voltage stress on devices or limiting the duty cycle. The operation principle of the converter and related relationships and waveforms are presented in the paper. Also, a comprehensive comparison between the proposed and other QZS based DC-DC converters is provided which confirms the superiority of the proposed converter. Simulations are done in PSCAD/EMTDC in order to investigate the MPPT capability of the converter. In addition, the valid performance and practicality of the converter are studied through the results obtained from the laboratory built prototype.
Fuel cell integrated unified power quality conditioner for voltage and curren...
Electrical and electronic devices when exposed to one or more power quality problems are prone to failure. This paper aims to enhance the quality of power in three-phase four-wire distribution grid using Fuel Cell Integrated Unified Power Quality Conditioner (FCI-UPQC). The proposed FCI-UPQC has four-leg converter on the shunt side and three-leg converter on the series side. A combination of a synchronous reference frame (SRF) and Instantaneous Reactive Power (IRP) theories are utilized to generate reference signals of the FCI-UPQC. Also, this paper proposes Adaptive Neuro-Fuzzy Inference System controller to maintain DC link voltage in the FCI-UPQC. The Adaptive Neuro-Fuzzy Inference System controller is designed like a sugeno fuzzy architecture and trained offline using data from the Proportional Integral (PI) controller. The obtained results proved that the proposed FCI-UPQC compensated power quality problems such as voltage sag, swell, harmonics, neutral current, source current imbalance in three-phase four-wire distribution grid. The presence of fuel cell in this work makes more effectiveness of the proposed system by providing real power support during supply interruption on the grid side.
More from Asoka Technologies (20)
Generation of Higher Number of Voltage Levels by Stacking Inverters of Lower ...
Generation of Higher Number of Voltage Levels by Stacking Inverters of Lower ...
Novel symmetric modular hybrid multilevel inverter with reduced number of sem...
Novel symmetric modular hybrid multilevel inverter with reduced number of sem...
A Variable DC Link based Novel Multilevel Inverter Topology for Low Voltage A...
A Variable DC Link based Novel Multilevel Inverter Topology for Low Voltage A...
A Simplified Space Vector Pulse-Width Modulation Scheme for Three-Phase Casca...
A Simplified Space Vector Pulse-Width Modulation Scheme for Three-Phase Casca...
A New Family of Step-up Hybrid Switched- Capacitor Integrated Multilevel Inve...
A New Family of Step-up Hybrid Switched- Capacitor Integrated Multilevel Inve...
A multi cell 21-level hybrid multilevel inverter synthesizes a reduced number...
A multi cell 21-level hybrid multilevel inverter synthesizes a reduced number...
A generalized multilevel inverter topology with reduction of total standing v...
A generalized multilevel inverter topology with reduction of total standing v...
Residential Community Load Management based on Optimal Design of Standalone H...
Residential Community Load Management based on Optimal Design of Standalone H...
Reliability evaluation of MPPT based interleaved boost converter for PV system
Reliability evaluation of MPPT based interleaved boost converter for PV system
Power Quality Improvement of Grid-Connected Photovoltaic Systems Using Trans-...
Power Quality Improvement of Grid-Connected Photovoltaic Systems Using Trans-...
Power optimisation scheme of induction motor using FLC for electric vehicle
Power optimisation scheme of induction motor using FLC for electric vehicle
Power Flow Control of Interconnected AC-DC Microgrids in Grid-Connected Hybri...
Power Flow Control of Interconnected AC-DC Microgrids in Grid-Connected Hybri...
Power flow control of hybrid micro grids using modified uipc
Power flow control of hybrid micro grids using modified uipc
Multifunctional grid tied pv system using modified klms control
Multifunctional grid tied pv system using modified klms control
Modelling and voltage control of the solar wind hybrid micro-grid with optimi...
Modelling and voltage control of the solar wind hybrid micro-grid with optimi...
Intelligent Power Sharing of DC Isolated Microgrid Based on Fuzzy Sliding Mod...
Intelligent Power Sharing of DC Isolated Microgrid Based on Fuzzy Sliding Mod...
Implementation of solar pv battery and diesel generator based electric vehic...
Implementation of solar pv battery and diesel generator based electric vehic...
Fuel cell integrated unified power quality conditioner for voltage and curren...
Fuel cell integrated unified power quality conditioner for voltage and curren...
Recently uploaded
DfMAy 2024 - key insights and contributions
We have compiled the most important slides from each speaker's presentation. This year’s compilation, available for free, captures the key insights and contributions shared during the DfMAy 2024 conference.
Design and Analysis of Algorithms-DP,Backtracking,Graphs,B&B
Dynamic Programming
Backtracking
Techniques for Graphs
Branch and Bound
Heap Sort (SS).ppt FOR ENGINEERING GRADUATES, BCA, MCA, MTECH, BSC STUDENTS
HEAP SORT ILLUSTRATED WITH HEAPIFY, BUILD HEAP FOR DYNAMIC ARRAYS.
Heap sort is a comparison-based sorting technique based on Binary Heap data structure. It is similar to the selection sort where we first find the minimum element and place the minimum element at the beginning. Repeat the same process for the remaining elements.
RAT: Retrieval Augmented Thoughts Elicit Context-Aware Reasoning in Long-Hori...
RAT: Retrieval Augmented Thoughts Elicit Context-Aware Reasoning in Long-Horizon Generation
一比一原版(IIT毕业证)伊利诺伊理工大学毕业证成绩单专业办理
IIT毕业证原版定制【微信：176555708】【伊利诺伊理工大学毕业证成绩单-学位证】【微信：176555708】（留信学历认证永久存档查询）采用学校原版纸张、特殊工艺完全按照原版一比一制作（包括：隐形水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠，文字图案浮雕，激光镭射，紫外荧光，温感，复印防伪）行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备，十五年致力于帮助留学生解决难题，业务范围有加拿大、英国、澳洲、韩国、美国、新加坡，新西兰等学历材料，包您满意。
◆◆◆◆◆ — — — — — — — — 【留学教育】留学归国服务中心 — — — — — -◆◆◆◆◆
【主营项目】
一.毕业证【微信：176555708】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【微信：176555708】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分→ 【关于价格问题（保证一手价格）
我们所定的价格是非常合理的，而且我们现在做得单子大多数都是代理和回头客户介绍的所以一般现在有新的单子 我给客户的都是第一手的代理价格，因为我想坦诚对待大家 不想跟大家在价格方面浪费时间
对于老客户或者被老客户介绍过来的朋友，我们都会适当给一些优惠。
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
选择实体注册公司办理，更放心，更安全！我们的承诺：可来公司面谈，可签订合同，会陪同客户一起到教育部认证窗口递交认证材料，客户在教育部官方认证查询网站查询到认证通过结果后付款，不成功不收费！
学历顾问：微信：176555708
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
6th International Conference on Machine Learning & Applications (CMLA 2024)
6th International Conference on Machine Learning & Applications (CMLA 2024) will provide an excellent international forum for sharing knowledge and results in theory, methodology and applications of on Machine Learning & Applications.
Immunizing Image Classifiers Against Localized Adversary Attacks
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Standard Reomte Control Interface - Neometrix
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Final project report on grocery store management system..pdf
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Recently uploaded (20)
Design and Analysis of Algorithms-DP,Backtracking,Graphs,B&B
Design and Analysis of Algorithms-DP,Backtracking,Graphs,B&B
Heap Sort (SS).ppt FOR ENGINEERING GRADUATES, BCA, MCA, MTECH, BSC STUDENTS
Heap Sort (SS).ppt FOR ENGINEERING GRADUATES, BCA, MCA, MTECH, BSC STUDENTS
Tutorial for 16S rRNA Gene Analysis with QIIME2.pdf
Tutorial for 16S rRNA Gene Analysis with QIIME2.pdf
RAT: Retrieval Augmented Thoughts Elicit Context-Aware Reasoning in Long-Hori...
RAT: Retrieval Augmented Thoughts Elicit Context-Aware Reasoning in Long-Hori...
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...
6th International Conference on Machine Learning & Applications (CMLA 2024)
6th International Conference on Machine Learning & Applications (CMLA 2024)
Immunizing Image Classifiers Against Localized Adversary Attacks
Immunizing Image Classifiers Against Localized Adversary Attacks
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...
Final project report on grocery store management system..pdf
Final project report on grocery store management system..pdf
Pile Foundation by Venkatesh Taduvai (Sub Geotechnical Engineering II)-conver...
Pile Foundation by Venkatesh Taduvai (Sub Geotechnical Engineering II)-conver...
Power quality improvement in distribution network using DSTATCOM with battery energy storage system
- 1. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 Power quality improvement in distribution network using DSTATCOM with battery energy storage system ABSTRACT The distribution static compensator (DSTATCOM) provides fast control of active and reactive powers to enable load compensation, harmonics current elimination, voltage flicker mitigation, voltage and frequency regulation. This paper presents power quality improvement technique in the presence of grid disturbances and wind energy penetration using DSTATCOM with battery energy storage system. DSTATCOM control is provided based on synchronous reference frame theory. A modified IEEE 13 bus test feeder with DSTATCOM and wind generator is used for the study. Power quality events during grid disturbances such as feeder tripping and re-closing, voltage sag, swell and load switching have been studied in association with DSTATCOM. The power quality disturbances due to wind generator outage, synchronization and wind speed variations have also been investigated. The study has been carried out using MATLAB/SIMULINK and the simulation results are compared with real time results obtained by the use of real time digital simulator (RTDS) for validating the effectiveness of proposed methodology. The proposed method has been proved to be effective in improvement of power quality with all disturbances stated above. KEYWORDS 1. Battery energy storage system 2. Radial distribution feeder 3. DSTATCOM 4. Synchronous reference frame theory SOFTWARE: MATLAB/SIMULINK
- 2. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 CIRCUIT DIAGRAM: Fig.1. Proposed DSTATCOM with BESS. SIMULATION RESULTS Fig.2. Feeder tripping and re-closing without DSTATCOM in the network (a) RMS voltage at bus 632, (b) active power flow and (c) reactive power flow
- 3. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 Fig.3. Feeder tripping and re-closing with DSTATCOM in the network (a) RMS voltage at bus 632, (b) active power flow and (c) reactive power flow
- 4. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 Fig.4. Load switching without DSTATCOM in the network (a) RMS voltage at bus 632, (b) active power flow and (c) reactive power flow Fig.5. Load switching with DSTATCOM in the network (a) RMS voltage at bus 632, (b) active power flow and (c) reactive power flow.
- 5. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 Fig.6. Voltage sag and swell (a) without DSTATCOM, (b) with DSTATCOM and (c) reactive power flow during voltage sag and swell. Fig. 7 Wind synchronization (a) voltage without DSTATCOM, (b) voltage with DSTATCOM, (c) active power flow with DSTATCOM and (d) reactive power flow with DSTATCOM.
- 6. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 Fig. 8. Wind outage (a) voltage without DSTATCOM, (b) voltage with DSTATCOM, (c) active power flow with DSTATCOM and (d) reactive power flow with DSTATCOM Fig. 9. Wind speed variation. CONCLUSION The proposed research work investigates into PQ events associated with distribution network due to grid disturbances such as voltage sag, swell, load switching, feeder tripping and re-closing. The DSTATCOM has been proposed to improve the power quality in the above events. The proposed DSTATCOM with SRF based control has been proved to be effective in improving the power quality in these events at grid level. The power quality events associated with wind operations such as wind generator outage, grid synchronization of wind generator and wind speed variations have been improved by the use of proposed DSTATCOM in the distribution network. From, these studies it has been established that the DSTATCOM can effectively be used to improve the power quality in the distribution network with wind generation and during grid disturbances. The results have been validated in real time utilizing RTDS. The real time results are very close to the simulation results which shows the effectiveness of proposed DSTATCOM with BESS for improvement of PQ in the distribution system. REFERENCES
- 7. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail:asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 [1] Ibrahim W, Morcos M. A power quality perspective to system operational diagnosis using fuzzy logic and adaptive techniques. IEEE Trans Power Deliv 2003;18(3):903–9. http://dx.doi.org/10.1109/TPWRD.2003.813885. [2] Ray P, Mohanty S, Kishor N. Classification of power quality disturbances due to environmental characteristics in distributed generation system. IEEE TransSust Energy 2013;4(2):302–13. http://dx.doi.org/10.1109/TSTE.2012.2224678. [3] Tascikaraoglu A, Uzunoglu M, Vural B, Erdinc O. Power quality assessment of wind turbines and comparison with conventional legal regulations: a case study in turkey. Appl Energy 2011;88(5):1864–72. http://dx.doi.org/10.1016/j. apenergy.2010.12.001. [4] Dash P, Padhee M, Barik S. Estimation of power quality indices in distributed generation systems during power islanding conditions. Int J Electr Power Energy Syst 2012;36(1):18– 30. http://dx.doi.org/10.1016/j.ijepes.2011.10.019. [5] Mahela OP, Shaik AG, Gupta N. A critical review of detection and classification of power quality events. Renew Sust Energy Rev 2015;41(0):495–505. http:// dx.doi.org/10.1016/j.rser.2014.08.070.