Set Up Basic Hydraulics Circuits
Eng.Muath N.BaniSalim
[email protected] 1
2
What is fluid power ?
• Fluid power is the technology that deals with the
generation , control ,and transmission of power using
pressurized fluids. It can be said that fluid power is the
muscle that moves industry. This is because fluid power
is used to push , pull ,regulate or drive virtually all the
machines of modern industry.
• Fluid power is subdivided into hydraulics using a liquid
such as mineral oil or water, and pneumatics using a gas
such as air or other gases
3
4
On this hydraulic excavator,
not only all working
movements (linear drives)
but also the propulsion of
the vehicle (rotary drive)
are hydraulically powered. 5
6
7
https://www.youtube.com/watch?x-yt-
ts=1422327029&x-yt-
cl=84838260&feature=player_detailpage&v
=fcIitdkVr_A
Start from the 35th sec
8
https://www.youtube.com/watch?feature=pl
ayer_detailpage&x-yt-cl=84838260&x-yt-
ts=1422327029&v=W7v4gLFSQsY
9
http://www.youtube.com/watch?feature=pla
yer_detailpage&v=plh8xMpc44k
Advantages of fluid power
• 1-Ease and accuracy of control
• By the use of simple levers and push buttons, the operator of
a fluid power system can readily start , stop speed up or slow
down and position forces that provides any desired
horsepower with tolerance as precise as one ten- thousand of
an inch
10
Ref: fluid power with applications 4th edition,
Anthony esposito
• 2-Multiplication of force
• A fluid power system (without using cumbersome gears,
pulleys , and levers) can multiply forces simply and efficiently
from a fraction of an ounce to several to several hundreds
tons of output.
11
• 3-Constant force or torque
• Only fluid power systems are capable of providing constant
force or torque regardless of peed change. This is
accomplished whether the work output moves a few inches
per hours.
12
• 4-Simplicity ,safety, economy
• In general , fluid power systems use fewer moving parts than
comparable mechanical or electrical systems. Thus , they are
simpler to maintain and operate . This ,in turn, maximize
safety ,compactness, and reliability.
13
The available Power Source for the
mechanical machines (Actuators)
• 1- Diesel engines
• 2-Electical Drive
• 3-Pnumatic actuators
• 4-Hydrulic actuators
14
• The choice of using electric, hydraulic, or
pneumatic motion systems is a
fundamental decision that affects
performance, costs, maintainability,
safety, ease of use, flexibility, and
reliability the needs of the application
and the capabilities of the technology
must be carefully evaluated—and then
balanced with a cost-benefit analysis.
15
Small note before the comparison
• As systems, neither one is better than the other.
There is no "Better", only "More suitable for a
specific purpose." Car tyres are Pneumatic...
they're full of air. Air is compre.
Hydraulic liquids, are the medium by which power is transferred in hydraulic machinery. Common hydraulic fluids are based on mineral oil or water.Examples of equipment that use hydraulic fluids include excavators and backhoes, hydraulic brakes, power steering systems, transmissions, garbage trucks, aircraft flight control systems, lifts, and industrial machinery.Work is taken from fluids due to mechanical advantage ,i.e, applying low input in form of force and getting a higher output in form of a large force .
Hydraulic liquids, are the medium by which power is transferred in hydraulic machinery. Common hydraulic fluids are based on mineral oil or water.Examples of equipment that use hydraulic fluids include excavators and backhoes, hydraulic brakes, power steering systems, transmissions, garbage trucks, aircraft flight control systems, lifts, and industrial machinery.Work is taken from fluids due to mechanical advantage ,i.e, applying low input in form of force and getting a higher output in form of a large force .
HYDRAULIC POWER GENERATING AND UTILIZING SYSTEMS
Introduction to fluid power system - Hydraulic fluids - functions, types, properties, selection and application.
POWER GENERATING ELEMENTS: Pumps, classification, working of different pumps such as Gear, Vane, Piston (axial and radial), pump performance or characteristics, pump selection factors- simple Problems.
POWER UTILIZING ELEMENTS: Fluid Power Actuators: Linear hydraulic actuators – Types and construction of hydraulic cylinders – Single acting, Double acting, special cylinders like tandem, Rodless, Telescopic, Cushioning mechanism.
Hydraulic Motors, types – Gear, Vane, Piston (axial and radial) – performance of motors.
There are two main types of hydraulic power transmission systems: hydrokinetic, such as the hydraulic coupling and the hydraulic torque converter, which use the kinetic energy of the liquid; and hydrostatic, which use the pressure energy of the liquid. The hydraulic coupling is a device that links two rotatable shafts.
Assignment details written in the attachmentsYou need to choose an.docxlesleyryder69361
Assignment details written in the attachments
You need to choose any one question.
Word limit: 2000 words
Footnotes: Oxford style
Intext reference: Harvard style
Bibliography: 15-20 sources including monographs, referred journal articles, news media report and political commentary.
Please do good work. Thank you
.
Assignment Details A high school girl has been caught shoplifting at.docxlesleyryder69361
Assignment Details A high school girl has been caught shoplifting at a high-end clothing store. Describe at least 4 of the most likely processes she will go through from the time the police arrive at the scene. Be sure to note the options available to the authorities when working with juveniles in regard to how this case is handled for each of the processes. Provide a description of the possible outcome for each option.
.
More Related Content
Similar to Set Up Basic Hydraulics Circuits Eng.Muath N.BaniSalim .docx
HYDRAULIC POWER GENERATING AND UTILIZING SYSTEMS
Introduction to fluid power system - Hydraulic fluids - functions, types, properties, selection and application.
POWER GENERATING ELEMENTS: Pumps, classification, working of different pumps such as Gear, Vane, Piston (axial and radial), pump performance or characteristics, pump selection factors- simple Problems.
POWER UTILIZING ELEMENTS: Fluid Power Actuators: Linear hydraulic actuators – Types and construction of hydraulic cylinders – Single acting, Double acting, special cylinders like tandem, Rodless, Telescopic, Cushioning mechanism.
Hydraulic Motors, types – Gear, Vane, Piston (axial and radial) – performance of motors.
There are two main types of hydraulic power transmission systems: hydrokinetic, such as the hydraulic coupling and the hydraulic torque converter, which use the kinetic energy of the liquid; and hydrostatic, which use the pressure energy of the liquid. The hydraulic coupling is a device that links two rotatable shafts.
Assignment details written in the attachmentsYou need to choose an.docxlesleyryder69361
Assignment details written in the attachments
You need to choose any one question.
Word limit: 2000 words
Footnotes: Oxford style
Intext reference: Harvard style
Bibliography: 15-20 sources including monographs, referred journal articles, news media report and political commentary.
Please do good work. Thank you
.
Assignment Details A high school girl has been caught shoplifting at.docxlesleyryder69361
Assignment Details A high school girl has been caught shoplifting at a high-end clothing store. Describe at least 4 of the most likely processes she will go through from the time the police arrive at the scene. Be sure to note the options available to the authorities when working with juveniles in regard to how this case is handled for each of the processes. Provide a description of the possible outcome for each option.
.
Assignment Details A 12-year-old boy was caught in the act of sexual.docxlesleyryder69361
Assignment Details A 12-year-old boy was caught in the act of sexually assaulting a 14-year-old female acquaintance by the victim's 16-year-old brother, who had arrived home and observed the juveniles in the act. The 12-year-old juvenile suspect, in addition to sexually assaulting the victim, had beaten her with the heel of a shoe that was nearby. The victim was almost unconscious when the police arrived. Following the incident, the juvenile was arrested and detained by local police on the following charges: Attempted sexual assault of a minor Aggravated assault Minor in possession of an alcoholic beverage Unlawful possession of a controlled substance (marijuana) The juvenile suspect was a latchkey kid (a child who returns from school to an empty home) from a single-parent home. His mother works from 2 p.m.–11 p.m. Monday through Friday, so the juvenile is often alone for hours upon his return from school. After a preliminary examination, the juvenile suspect explained that the victim purchased the marijuana and the alcohol earlier that same day. The juvenile explained that the victim had invited him to her house because they had "been liking each other" for a long time. Further, the juvenile explained that the alcohol and drugs were in the home when he arrived. He said that he and the victim began by smoking marijuana and drinking beer before they began kissing and fondling one another. Next, according to the juvenile suspect, they started to have what he described as consensual sex. After a short while, they were interrupted by the victim's brother, who had come home from work. The victim’s brother then called the police to report the incident.
The juvenile had prior detentions for violation of curfew, truancy, and attempted sexual battery. No further explanations are given. Write an essay of 750–800 words, divided into 3 sections: the perspectives of the police officer, the state's attorney, and the judge. Do each of these components of the criminal justice system see the offender as a status offender for any of the charges? Discuss your opinion of the status offender from the perspective of each criminal justice component (law enforcement, state's attorney, and the judge). Are the charges viewed by each of the criminal justice components listed below as delinquent acts? Include the following:
From the perspective of the police officer What typically happens to this juvenile before he even goes to juvenile court? How does law enforcement process the incident? From the perspective of the state's attorney Make suggestions to the court on how the boy should be punished or sentenced. From the perspective of the judge Based on the facts of the case and the procedures of the juvenile justice system, what would be the most appropriate finding of the court? What options does the judge have in this incident? Be sure to cite all references in APA format. You will be marked down if you use any adult court terminology in .
Assignment Details (350 WORDS)The last quarter of the 20th c.docxlesleyryder69361
Assignment Details (350 WORDS)
The last quarter of the 20th century saw the dawning of the age of technology. Technological advances have sprung forward at such a quickening pace that it is difficult to remain on pace with it. What was once the latest, most sophisticated device yesterday, is now today’s old news and tomorrow’s junk pile.
In the war of protecting infrastructure elements and sectors, technology has replaced human presence. Technology is now the "eyes and ears" of protection. Technology is used to test steel and concrete, audit financial records, record data, project an analysis, and provide a security presence where people cannot.
Focus your discussion on the following:
Are the current types of technology used in protecting critical infrastructure effective? Why or why not?
What major technological issues can you foresee with regard to critical infrastructure protection? Explain
.
Assignment Details (300 words and references)Collaborati.docxlesleyryder69361
Assignment Details (300 words and references)
Collaboration leverages the collective knowledge of a health care team. Peer evaluation and support, provided in the spirit of continuous improvement and organizational success, result in higher quality deliverables than generally possible by the efforts of an individual.
Describe the process you plan to use to conduct research, identify findings, and develop the project that is due in Unit 5.
Present a brief outline indicating how you intend to organize the project deliverable.
.
Assignment Details (2-3 pages) Research information about cu.docxlesleyryder69361
Assignment Details (2-3 pages)
Research information about current considerations and challenges related to the financial and budgetary systems in health care organizations. Consider the use of data analytics and tools in the monitoring, assessing, and evaluating of the performance of health care organizations. Include a discussion of the importance and efficacy of financial statements used in the decision-making process of health care organizations.
Support your work with at least 4 academic or professional peer-reviewed sources published within the past 5 years.
.
Assignment Details (250 - 300 words)Now that the research .docxlesleyryder69361
Assignment Details (250 - 300 words)
Now that the research end is in sight, are your ethical obligations as a researcher over with?
What are some important ethical obligations during the reporting and sharing of your findings?
How do you avoid these pitfalls?
.
Assignment detailed instructions Write a three-page (minimum of 7.docxlesleyryder69361
Assignment detailed instructions: Write a three-page (minimum of 750 words) essay addressing the following eight questions. The paper should be in APA format, double spaced, 12 font, and include references/bibliography(MINIMUM 3) on the fourth page.
Write eight paragraphs addressing these eight prompts:
Part 1 Intercultural Competence
1. Identify and describe a specific issue of concern to a specific community for the focus of your essay. Choose from DACA and immigration laws, racism, prochoice/prolife, millennials, rape culture, gender equality, same-sex marriage, marijuana laws, religion in schools, human trafficking, white privilege, police brutality, gun control, or another social justice issue.
2. Define culture and cultural competence and discuss how your own culture has shaped your identity and world view related to the issue you chose.
3. Discuss significant characteristics about another culture and how and why they see this issue perhaps differently than you. (put yourself in their shoes, see it from their perspective)
4. Discuss how you have or how you might adjust your actions and communication style to successfully interact with someone from another culture/viewpoint.
Part 2 Engagement with Communities: Social Responsibility
5. Discuss your civic responsibility related to the issue you chose to write about in this essay.
6. Discuss effective participation in civic engagement activities related to this issue.
7. Describe your understanding of the purpose and benefits of civic engagement.
8. If you have engaged in civic activities related to this issue or another issue of importance to you, describe that experience. What was the purpose? What were the benefits? What did you learn?
.
Assignment detailed instructions Write a three-page (minimum of 750.docxlesleyryder69361
Assignment detailed instructions: Write a three-page (minimum of 750 words) essay addressing the following eight questions. The paper should be in APA format, double spaced, 12 font, and include references/bibliography(MINIMUM 3) on the fourth page.
Write eight paragraphs addressing these eight prompts:
Part 1 Intercultural Competence
1. Identify and describe a specific issue of concern to a specific community for the focus of your essay. Choose from DACA and immigration laws, racism, prochoice/prolife, millennials, rape culture, gender equality, same-sex marriage, marijuana laws, religion in schools, human trafficking, white privilege, police brutality, gun control, or another social justice issue.
2. Define culture and cultural competence and discuss how your own culture has shaped your identity and world view related to the issue you chose.
3. Discuss significant characteristics about another culture and how and why they see this issue perhaps differently than you. (put yourself in their shoes, see it from their perspective)
4. Discuss how you have or how you might adjust your actions and communication style to successfully interact with someone from another culture/viewpoint.
Part 2 Engagement with Communities: Social Responsibility
5. Discuss your civic responsibility related to the issue you chose to write about in this essay.
6. Discuss effective participation in civic engagement activities related to this issue.
7. Describe your understanding of the purpose and benefits of civic engagement.
8. If you have engaged in civic activities related to this issue or another issue of importance to you, describe that experience. What was the purpose? What were the benefits? What did you learn?
.
Assignment Description 400 wordsOne of the more important me.docxlesleyryder69361
Assignment Description
400 words
One of the more important measures in regard to international economics is the balance of payments. Think of it as a national accounting measure that looks at the flow of goods and services into and out of an economy in a given period of time. It also shows capital flows into and out of a country. Until 1980, the United States tended to run a positive-to-neutral balance of payments position and was a creditor nation. In the course of the past 30 years, the United States has moved to a negative balance of payments and to being a debtor nation.
Review and discuss the following:
Discuss the importance of the balance of payments as an accounting measure.
Discuss the current account and its components and the capital and financial accounts and their components.
How important is the U.S. deficit in traded goods in regard to the balance of payments?
Here are some relevant articles to help you with this assignment:
The Changing Nature of the U.S. Balance of Payments
Balance of Payments
Please submit your assignment.
.
Assignment DescriptionYou work for a small community hospita.docxlesleyryder69361
Assignment Description
You work for a small community hospital that has recently updated its health record system to a modern electronic health record (EHR) system. As a health care manager, you have been asked to meet with the health information manager (HIM) and analyze the efficiency, security, and privacy of your current health records system. Your organization has very high standards and a culture of keeping up with current trends. After your analysis, you have been asked to provide a detailed report to the hospital's chief operating officer (COO) detailing the following:
Examine the emergence of technology and electronic health systems in health care since the passage of the Health Insurance Portability and Accountability Act (HIPAA).
Provide an analysis of the current trends in health care record keeping and charting as they relate to advancements in technology.
Assess ways in which contemporary patient records systems can support health care operations including privacy, quality patient care delivery, insurance and cost administration, and records access and retention.
Present your findings in an executive summary of 5–7 pages.
.
Assignment description The tourism industry represents about .docxlesleyryder69361
Assignment description
:
The tourism industry represents about 10.4% of Australia’s gross domestic product (GDP) and 12.2% of total employment in 2018. Unfortunately, the Tourism & Hospitality (T&H) Sector in Australia has been badly affected by the twin catastrophic events: first, it was devastated by the unprecedented magnitude of the bushfires from October 2019 to January 2020. Just as the affected communities were working towards recovery, the outbreak of the Covid-19 pandemic caused a massive blow to the T&H Sector.
ps: two files, first file digital poster, second file brief disruption (100 words) and reference list.
Ignore task 2 discusion forum.
.
Assignment DescriptionYou will prepare and deliver a speech .docxlesleyryder69361
Assignment Description
You will prepare and deliver a speech using the power of words. You will use the devices to convey your emotions and move your audience to connect with your purpose. Get your message across to your audience by using many strategies. You will create images and emotion in your audience using storytelling, humor or sharing personal experiences (both heartbreaking and fulfilling). You will also apply the oratorical skills that you have been exploring.
Completion Instructions
Presentation Topic
: For this presentation, you will act as a representative agent for the University, recruiting prospective students from your country of origin. Prepare a speech outline that persuades the prospects. Describe, among other ideas: Your experiences, emotions and challenges of your life in Canada, moving around the City, Campus activities, career projection and Permanent Residency possibilities. Tell a story, add humor, move your audience to feel your story.
.
Assignment DescriptionYou are to write an essay in which you .docxlesleyryder69361
Assignment Description:
You are to write an essay in which you contrast two viewpoints on a topic and argue for one of them. Over the coming few weeks, you will work through drafting youressay, with the goal of producing a well-written essay. Send your final essay to
[email protected]
no later than 11:59 PM on December 11, 2019. There is no need to hand in a hard copy. You must submit your work by the official deadline. Extensions may be granted only in exceptional circumstances, and when sought in advance. Students who submit the work late without an agreed extension will face the following penalty: loss of 2 marks per day.
Assignments Deadlines:
Draft:
December
2nd,
2019
Final Submission: December
11th,
2019
If you have trouble coming up with a good topic, you might want to consider the following questions:
• Are the effects of social networking sites positive or negative? • Should parents give their teenagers an allowance?• Can music help us emotionally?• Should smoking be banned?• Are cell phones dangerous?• Is social media good?
.
Assignment DescriptionYou are the lead human–computer intera.docxlesleyryder69361
Assignment Description
You are the lead human–computer interaction (HCI) engineer on a major design project for an organization of your choice. Employees or customers will use this new system and user interface (UI) design to perform data entry for the organization. The UI will need to provide the required input and output to characterize the type of data collected by the organization.
Choose an organization, such as a business, nonprofit group, government, or another organization. Provide a description of your chosen organization, including the following:
Name of the organization
Business type
Size of the organization
Planned users for the interface
Type of data that must be captured
The use of the data
Part of your job is to elicit and define the UI requirements for this new design.
Write a neatly-formatted report that includes the following:
Title page
Report of 4–6 pages consisting of the following:
Introduction to the contents of the report
Description of the organization, as detailed above
Identification of the following elements that must be included in this UI design for the organization:
Fields you expect to see in this UI screen design (e.g., menus, data entry screens, boxes, help, fields, drop-down menus)
List of requirements that will ensure that this interface design can easily capture data input in multiple languages
Explanation of interface alternatives that will be needed for different language orientations (e.g., different characters for right and left)
Effective conclusion
References must be properly cited in APA style
.
Assignment DescriptionYou are now ready to start representin.docxlesleyryder69361
Assignment Description
You are now ready to start representing your system integration project by utilizing a system integration framework, which you researched as part of your Discussion Board assignment. You will also decide which components you might want to acquire and which components you want to develop internally.
Assignment Guidelines
For this week’s assignment, you will provide detail on the overall system integration architecture and the implementation framework.
New Content (Week 4)
Proposed System Integration Components Architecture
Thoroughly describe the architecture of the proposed integrated system, including all interfaces and components for the system integration and deployment.
Represent this architecture diagrammatically.
Discuss which components and interfaces could be acquired and those that need to be developed from scratch.
Implementation Framework
Select and describe in detail the framework that you used to define and implement the system integration project.
Define the project in terms of the selected framework.
Discuss advantages for using the selected framework.
Discuss integration challenges that were highlighted by defining the framework.
Make sure that the document is in APA format.
Submit the document for grading.
.
Assignment DescriptionManagement is worried, after consultin.docxlesleyryder69361
Assignment Description
Management is worried, after consulting with the IT department that the current documentation of the present architecture was not done correctly and with the required details, therefore if IoT is implemented they desire more detailed graphical documentation on its implementation. Provide the following components as part of an architecture model graphic to be delivered to management for the asset tracking system:
Provide an introduction to the paper concerning the purpose of the graphic and the overall solution being recommended by the asset tracking IoT implementation (2-3 paragraphs).
Provide descriptive information regarding the architectural model graphic, and the details describing the devices, applications, Cloud/Server environment and gateway. (2 pages)
Provide the architectural graphic with the components below (Describe each of the objects on the diagram below, the interconnections or interfaces, types of data traveling across the connections, active protocols, cabling or wireless connections, and implemented security):
Devices (Generic device - Sensing and Actuating Devices)
IoT Application (transforms the data for value to the user)
Cloud/Server (data storage, processing and management)
Gateway capability (data is acquired, forwarded to the communications network)
Provide a conclusion to the paper summarizing the content and purpose of the paper.
An example of the required level of detail for your graphic can be found at
http://www.latogalabs.com/2017/05/iot-architecture-the-journey/
.
.
Assignment Description
Ego Integrity Presentation
Imagine you are working as a charge nurse in an assisted living facility. Your unit houses twenty older adults. The residents of this unit are cognitively functional without evidence of cognitive decline. The residents are elderly and do require varying degrees of physical assistance with ADLs. Create a PowerPoint outlining strategies you can incorporate in the assisted living facility to promote ego integrity for your residents. What group and individual activities can you incorporate?
Assignment Expectations:
Length: 10-15 content slides
Structure: Include a title slide, objective slide, and reference slide in APA format. These do not count towards the minimum content slide count for this assignment. Be sure to fully explain all slides in the Speaker Notes.
References: Use appropriate APA style in-text citations and references for all resources utilized to answer the questions. A minimum of two (2) scholarly sources are required for this assignment.
Rubric: This assignment uses a rubric for scoring. Please review it as part of your assignment preparation and again prior to submission to ensure you have addressed its criteria at the highest level.
Format: Save your assignment as a Microsoft PPT document (.pptx)
.
Assignment DescriptionCultural Group Exploration Assignment .docxlesleyryder69361
Assignment Description
Cultural Group Exploration Assignment (in-text citation and APA format 7th edition) Required.
Understanding the impact of culture on the health beliefs / practices of a client is an important component of assessing, planning, implementing and evaluating comprehensive nursing care. To provide culturally competent care is a worthy goal. Insensitivity to a client’s culture may render interventions fruitless.
Purpose
: The PURPOSE of this assignment is to develop in the learner an awareness of the health beliefs / practices of a culture different from their own.
Guidelines
: Download the
Cultural Exploration Guidelines
before you start the activity and refer to it as you work. Submit completed table along with reference page to your faculty mentor through the Submissions tab and then post it in your group discussion.
Cultural Exploration Table and Rubric
is attached below
.
Assignment description from the syllabusEach member of the matc.docxlesleyryder69361
Assignment description from the syllabus:
Each member of the matching team will individually submit a 3-page, double-spaced write-up on the case. To receive full credit, you should describe the firm’s opportunity/dilemma, evaluate/analyze their strategic options, and describe your recommendation on the most promising path(s) forward in their strategy. Make sure to back up your evaluation and recommendations with evidence/facts from the case. Three pages is very short—make sure that you are concise and to-the-point in zeroing in on key aspects of the case.
At the end of your write-up, ask one or two questions that you are more concerned about the firm.
ANU Press
Chapter Title: OCCUPATIONAL STRESS
Chapter Author(s): SU MON KYAW-MYINT and LYNDALL STRAZDINS
Book Title: Health of People, Places and Planet
Book Subtitle: Reflections based on Tony McMichael’s four decades of contribution to
epidemiological understanding
Book Editor(s): COLIN D. BUTLER, JANE DIXON, ANTHONY G. CAPON
Published by: ANU Press. (2015)
Stable URL: https://www.jstor.org/stable/j.ctt1729vxt.18
JSTOR is a not-for-profit service that helps scholars, researchers, and students discover, use, and build upon a wide
range of content in a trusted digital archive. We use information technology and tools to increase productivity and
facilitate new forms of scholarship. For more information about JSTOR, please contact [email protected]
Your use of the JSTOR archive indicates your acceptance of the Terms & Conditions of Use, available at
https://about.jstor.org/terms
This book is licensed under a Creative Commons Attribution-NonCommercial-
NoDerivatives 4.0 International. To view a copy of this license, visit
http://creativecommons.org/licenses/by-nc-nd/4.0/.
ANU Press is collaborating with JSTOR to digitize, preserve and extend access to Health of
People, Places and Planet
This content downloaded from 63.145.155.130 on Tue, 25 Sep 2018 00:31:54 UTC
All use subject to https://about.jstor.org/terms
81
4
OCCUPATIONAL STRESS
SU MON KYAW-MYINT AND LYNDALL STRAZDINS
Abstract
In 1979, Tony McMichael co-authored a paper showing how occupational stress
not only affected mental health; it also exacerbated the effect of chemical and
physical hazards on respiratory and skin symptoms. This study was among
the first to place occupational stress within the same framework as chemical
and physical hazards. It also showed that stress and mental health faced
complex assessment challenges, but that these were similar to those faced by
the assessment of exposure to chemical and physical hazards, especially in
large-scale epidemiological studies.
More recently, occupational stress has been termed a ‘psychosocial hazard’ by
some jurisdictions in an attempt to place it into the existing occupational risk
management and risk assessment framework. However, progress has been slow
and regulation of occupational stress remains outside standard occupational
health and safety .
Biological screening of herbal drugs: Introduction and Need for
Phyto-Pharmacological Screening, New Strategies for evaluating
Natural Products, In vitro evaluation techniques for Antioxidants, Antimicrobial and Anticancer drugs. In vivo evaluation techniques
for Anti-inflammatory, Antiulcer, Anticancer, Wound healing, Antidiabetic, Hepatoprotective, Cardio protective, Diuretics and
Antifertility, Toxicity studies as per OECD guidelines
Synthetic Fiber Construction in lab .pptxPavel ( NSTU)
Synthetic fiber production is a fascinating and complex field that blends chemistry, engineering, and environmental science. By understanding these aspects, students can gain a comprehensive view of synthetic fiber production, its impact on society and the environment, and the potential for future innovations. Synthetic fibers play a crucial role in modern society, impacting various aspects of daily life, industry, and the environment. ynthetic fibers are integral to modern life, offering a range of benefits from cost-effectiveness and versatility to innovative applications and performance characteristics. While they pose environmental challenges, ongoing research and development aim to create more sustainable and eco-friendly alternatives. Understanding the importance of synthetic fibers helps in appreciating their role in the economy, industry, and daily life, while also emphasizing the need for sustainable practices and innovation.
How to Make a Field invisible in Odoo 17Celine George
It is possible to hide or invisible some fields in odoo. Commonly using “invisible” attribute in the field definition to invisible the fields. This slide will show how to make a field invisible in odoo 17.
Read| The latest issue of The Challenger is here! We are thrilled to announce that our school paper has qualified for the NATIONAL SCHOOLS PRESS CONFERENCE (NSPC) 2024. Thank you for your unwavering support and trust. Dive into the stories that made us stand out!
Palestine last event orientationfvgnh .pptxRaedMohamed3
An EFL lesson about the current events in Palestine. It is intended to be for intermediate students who wish to increase their listening skills through a short lesson in power point.
Set Up Basic Hydraulics Circuits Eng.Muath N.BaniSalim .docx
1. Set Up Basic Hydraulics Circuits
Eng.Muath N.BaniSalim
[email protected] 1
2
What is fluid power ?
• Fluid power is the technology that deals with the
generation , control ,and transmission of power using
pressurized fluids. It can be said that fluid power is the
muscle that moves industry. This is because fluid power
is used to push , pull ,regulate or drive virtually all the
machines of modern industry.
• Fluid power is subdivided into hydraulics using a liquid
such as mineral oil or water, and pneumatics using a gas
such as air or other gases
2. 3
4
On this hydraulic excavator,
not only all working
movements (linear drives)
but also the propulsion of
the vehicle (rotary drive)
are hydraulically powered. 5
6
7
https://www.youtube.com/watch?x-yt-
ts=1422327029&x-yt-
cl=84838260&feature=player_detailpage&v
=fcIitdkVr_A
Start from the 35th sec
4. • 2-Multiplication of force
• A fluid power system (without using cumbersome gears,
pulleys , and levers) can multiply forces simply and efficiently
from a fraction of an ounce to several to several hundreds
tons of output.
11
• 3-Constant force or torque
• Only fluid power systems are capable of providing constant
force or torque regardless of peed change. This is
accomplished whether the work output moves a few inches
per hours.
12
• 4-Simplicity ,safety, economy
• In general , fluid power systems use fewer moving parts than
comparable mechanical or electrical systems. Thus , they are
simpler to maintain and operate . This ,in turn, maximize
safety ,compactness, and reliability.
5. 13
The available Power Source for the
mechanical machines (Actuators)
• 1- Diesel engines
• 2-Electical Drive
• 3-Pnumatic actuators
• 4-Hydrulic actuators
14
• The choice of using electric, hydraulic, or
pneumatic motion systems is a
fundamental decision that affects
performance, costs, maintainability,
safety, ease of use, flexibility, and
reliability the needs of the application
and the capabilities of the technology
must be carefully evaluated—and then
balanced with a cost-benefit analysis.
15
6. Small note before the comparison
• As systems, neither one is better than the other.
There is no "Better", only "More suitable for a
specific purpose." Car tyres are Pneumatic...
they're full of air. Air is compressible, which is
why it's used. If you filled your car tyres with
Hydraulic fluid (which is incompressible) you
would not only increase the weight of the tyres
dramatically (and hence increase the relative
tread-wear), but also make them hard,
decreasing their ability to absorb shock.
16
17
Ref :
http://www.boschrexroth.com.tr/country_units/america/united_s
tates/en/C
reative_Diversions/TopTenLists/TopTen_WhitePapers/BRUS_-
_Elec_Hyd_Pneu.pdf
Power
• Is the rate or speed at which the work is done.
It is divided by time.
7. • Expressed in watt (W) or horsepower (hp)
• 1hp=746 watts
• 1 hp = 550 ft lb of work done per second
• 1 hp = 33,000 ft lb of work per minute
• Whenever work is done energy is used
18
Power transmission
• If a force F_1 is applied to
an area A_1 of a liquid, a
pressure p results. If, as in
this case, the pressure acts
on a larger surface A_2,
then a larger counter-force
F_2 must be maintained. If
A_2 is three times as large
as A1, then F_2 will also be
three times as large as F_1.
• Hydraulic power
transmission is comparable
to the mechanical law of
levers.
19
9. • This simplified block
diagram shows the
division of hydraulic
systems into a signal
control section and a
hydraulic power
section. This signal
control section is used
to activate the valves in
the power control
section.
22
Hydraulic power section
• The diagram of the hydraulic
power section is complemented
in this case by a circuit diagram
to allow correlation of the
various function groups; the
power supply section contains
the hydraulic pump and drive
motor and the components for
the preparation of the hydraulic
fluid. The energy control
section consists of the various
valves used to provide control
and regulate the flow rate,
pressure and direction of the
hydraulic fluid. This drive
section consists of cylinders or
hydraulic motors, depending on
10. the application in question.
23
24
Interaction of components
• The animations show
the sequences in a basic
hydraulic circuit in
simplified form - the
actuation and spring
return of the final
control element (4/2-
way valve), the advance
and return of the drive
component (double
acting cylinder) and the
opening and closing of
the pressure relief
valve.
25
Interaction of components
(Animation)
26
12. Interaction of components
(Animation)
32
Interaction of components
(Animation)
33
34
Hydraulic Actuators
Double acting cylinder
• In the case of double acting
cylinders, both piston surfaces
can be pressurized. A working
movement can thus be
performed in both directions.
• With double acting cylinders
with a single-sided piston rod,
different forces and speeds are
obtained on the advance and
13. return strokes due to the
difference in area between the
piston surface and annular
piston surface.
35
Single acting cylinder
• In the case of a single acting
cylinder, only the piston side is
pressurized with hydraulic
fluid. The cylinder can thus
carry out work only in one
direction. The fluid which flows
into the piston chamber causes
a pressure to build up the
surface of the piston. The
piston travels into its forward
end position. The return stroke
is effected by a spring, the
dead weight of the piston rod
or an external load.
36
Double acting cylinder with end
position cushioning
• Cylinder with end position
cushioning are used to
brake high stroke speeds
14. smoothly and prevent hard
impacts at the end of the
stroke. Shortly before the
end position is reached, the
cross- section for the
outflow of fluid is reduced
by the built-in cushioning
pistons and then finally
closed. The hydraulic fluid is
then forced to escape
through a flow control
valve.
37
End position cushioning
(Animation)
• The illustration shows first the
advance of the piston rod from a
mid-position to the forward end
position, with cushioning at the
end of the advance movement.
The non-return valve is open
during the return stroke.
• The animation shows the opening
of the pressure limiter after a
certain pressure has been built
up on the outlet side by the
cushioning piston.
38
15. End position cushioning
• The piston is a short distance
before its end position; the
hydraulic fluid on the piston-rod
side must escape via the
adjustable flow control valve
above the piston rod
• This type of end position
cushioning is used for stroke
speed between 6 m/min and 20
m/min. At higher speed,
additional cushioning or braking
devices must be used.
39
Telescopic cylinder
40
• This type contains
multiple cylinders
that slides inside
each other. They are
used where long
work strokes are
required.
16. Cylinder with double end positions
• Here the rod extends
out of the cylinder at
both ends. For
such cylinders, the
word extend and
retract have no
meaning
41
Hydraulic motors
• 1- Continues rotation
• 2- Limited rotation
42
Hydraulic
Motor
Single acting
cylinders
Double acting
17. cylinders
Hydraulic power unit
• The hydraulic power unit
(power supply unit)
provides the energy
required for the hydraulic
installation. Its most
important components are
the reservoir (tank) , drive
(electric motor), hydraulic
pump, pressure relief valve
(safety valve), filter and
cooler. The hydraulic power
unit may also act as a
carrier for other devices
(gauges, directional control
valves). 44
Hydraulic power unit: Reservoir
• The hydraulic reservoir contains
the hydraulic fluid required the
operate the installation. Within
the reservoir, air, water and solid
matter are separated out of the
hydraulic fluid.
• The size of the reservoir will
depend on the practical
18. application involved; for
stationary systems, the volume of
fluid delivered by the pump in 3
to 5 minutes can be taken as a
guide. In mobile hydraulic
systems, on the other hand, the
reservoir contains only the
maximum quantity of hydraulic
fluid required.
45
Externally toothed gear pump
• Develops flow by carrying fluid
between the teeth of two
meshing gears. One of the gears
is connected to a drive shaft
connected to the prime mover.
The second gear is driven as it
meshes with the drive gear. The
suction side is where teeth come
out of mesh , and it is here where
the volume expands, bringing
about a reduction in pressure to
below atmospheric pressure.
Fluid is pushed into this void by
atmospheric pressure because
the oil supply tank is vented to
the atmosphere
46
19. Internally toothed gear pump
• The inner gear is driven by a
motor. The teeth of the inner
wheel drive the outer gear wheel.
The rotary motion creates a
vacuum in the gaps between the
teeth, causing hydraulic fluid to
be sucked in. On the other side,
the teeth engage once more and
oil is displaced from the tooth
chambers.
• The design can deliver pressures
of up to approx. 175 bar.
Hydraulic motors represent the
reverse of the function principle.
47
48
Circuit diagram: Return flow filter
• An oil filter situated in the
return line to the tank has
the advantage that the filter
is thus easy to maintain. A
disadvantage, however, is
20. that contamination is
removed from the hydraulic
fluid only after it has passed
through the hydraulic
components.
• This configuration is often
used.
49
Circuit diagram : Pump inlet filter
• With this configuration, the
pump is protected from
contamination. The filter is,
on the other hand, less
easily accessible.
• If these filters have a too
fine mesh, suction problems
and cavitation effects may
occur. Additional coarse
filters upstream of the
pump are recommended.
50
Circuit diagram: Pressure line filter
• Pressure filters can be
installed selectively
21. upstream of valves which
are sensitive to
contamination; this also
enables smaller mesh sizes
to be used.
• A pressure-resistant
housing is required, which
makes this configuration
more expensive.
51
Circuit diagram: Contamination
indicator
• It is important that the
effectiveness of a filter can be
checked by a contamination
indicator. The contamination of a
filter is measured by the pressure
drop; as the contamination
increases, the pressure upstream
of the filter increases. The
pressure acts on a spring- loaded
piston. As the pressure increases,
the piston is pushed against a
spring.
• There are a number of different
display methods. Either the
piston movement is directly
visible or it is converted into an
electrical or visual indication by
22. electrical contacts.
52
Water cooler
• With this design of cooler,
hydraulic fluid is fed through
tubes over which coolant (water)
flows. The heat which is
discharged can be re-used.
• The operating temperature in
hydraulic installations should not
exceed 50 - 60ºC, since this
would cause an unacceptable
reduction in viscosity, leading to
premature aging of the fluid. In
comparison with air cooling,
operating costs a higher due to
the required coolant and the
susceptibility to corrosion.
Temperature difference of up to
approx. 35ºC can be handled.
53
Air cooler
• Hydraulic fluid from the
return line flows
through a coiled pipe
23. which is cooled by a
fan.
• The advantages here
are simplicity of
installation and low
operating costs. The
noise of the fan may be
a nuisance
54
Heating element
• Heaters are often required
to ensure that the optimum
operating temperature is
reached quickly. Heating
elements or flow
preheaters are used for
heating and pre-heating
hydraulic fluid.
• If the viscosity is to high,
the resulting increase in
friction and cavitation leads
to greater wear.
55
Circuit diagram: Hydraulic power
unit
24. • The illustration shows
the detailed circuit
symbol for a hydraulic
power unit.
• Since this is an
combination unit, a
dot/dash line is placed
around the symbols
representing the
individual units.
56
57
Properties of hydraulic oil
• The single most important material in a hydraulic fluid
itself. Hydraulic fluid characteristics have a crucial effect
on equipment performance and life.
• Essentially, hydraulic fluid has four primary functions:
1) To transmit power
2) To lubricate moving parts
25. 3) To seal clearness between mating parts
4) To dissipate heat
58
To accomplish properly these primary functions and be
practical from a safety and cost point of view, a hydraulic
fluid should have the following properties:
lity
26. This is a challenging list
, and no single hydraulic
fluid possesses all of
these desirable
characteristics. The fluid
power designer must
select the fluid that
comes the closest to
being ideal overall for a
particulate application
Pressure relief valve
• In this design incorporating
a poppet valve, a seal is
pressed against the inlet
port P by a pressure spring
when the valve is in its
normal position.
• In this situation, for
example, an unloaded
27. piston rod is executing an
advance stroke and the
entire pump delivery is
flowing to the cylinder.
60
61
Circuit diagram: Pressure relief
valve
• As soon as the force
exerted by the inlet
pressure at A exceeds the
opposing spring force, the
valve begins to open.
• In this situation, for
example, the piston rod is
fully advanced; the entire
pump delivery is flowing at
the preset system pressure
to the tank.
62
PRV used to limit system pressure
• This illustration shows a
28. pressure relief valve within
a basic hydraulic circuit
(used to control a double
acting cylinder).
• The resistances at the
outlet (tank line, filter) must
be added to the force of the
spring in the pressure relief
valve. See also the
animation “Interaction of
components” (topic 5).
63
PRV used to limit system pressure
• This illustration shows
the same circuit as the
previous illustration,
but with the cut-away
view of the PRV
replaced by the
appropriate circuit
symbol.
64
Two-way pressure regulator
• This valve is normally open.
The outlet pressure (A) acts
29. via a pilot line on the left-
hand surface of the pilot
piston against an adjustable
spring force.
• Pressure regulators reduce
the inlet pressure to an
adjustable outlet pressure. It
is appropriate to use these
in hydraulic installations
only if different pressures
are required.
65
Two way pressure regulator
• In the circuit illustrated,
the piston rod of the
cylinder is executing an
advance stroke. The
pressure at the outlet A
of the pressure
regulator is less than
the system pressure at
P and constant.
66
Circuit diagram: 2-way pressure
regulator
30. • The illustration shows
the same circuit as the
previous illustration,
but with the 2-way
pressure regulator in
the form of a circuit
symbol.
67
68
Directional Control Valves
2/2-way valve
• The 2/2-way valve has a
working port A, a supply port P
and a leakage-oil port L. In the
case of the valve shown here,
of slide design, flow from P to A
is closed in the normal position.
• A relief line leading to the
leakage-oil port is provided to
prevent a build-up of pressure
in the spring and piston
chambers.
69
31. 2/2-way valve (2)
• The 2/2-way valve is
actuated and the
passage from P to A is
open.
• 2/2-way valves are also
available which are
normally open from P
to A.
70
2/2-way valve as by-pass valve
• This example shows a
2/2-way valve used as a
by-pass valve; when the
2/2-way valve is
actuated, the flow
control valve 0V3 is by-
passed, causing the
piston rod of the
cylinder to advance at
maximum speed.
71
32. Circuit diagram: 2/2-way valve as
by-pass valve
• The illustration shows
the same circuit as the
previous illustration,
but with the functional
representation of the
2/2-way valve replaced
by a circuit symbol.
72
Circuit diagram: 2/2-way valve as
final control element
• In its initial position, the
cylinder is advanced. If the 2/2-
way valve 0V1 is actuated, the
entire volumetric flow passes to
the tank and piston rod of the
cylinder is reset by the external
load m. If 0V1 is not actuated,
the system pressure set on the
pressure limiter 0V2 builds up
and the piston rod advances.
• In the initial position, the pump
operates against the preset
system pressure, which has an
unfavorable effect on the
power balance of the circuit
shown.
33. 73
2/2-way valve as final control
element (Animation)
• The animations show
the actuation and
release of the 2/2-way
valve, which causes the
piston rod of the
cylinder to advance and
retract.
74
2/2-way valve as final control
element (Animation)
75
2/2-way valve as final control
element (Animation)
76
Directional control valves can be classified according to:
34. • Number of ports
• Number of positions
• Actuating methods (later on)
Example: A 3/2 directional control valve would have three ports
and two spool
positions. Ports No. / Position No.
• Number of Ports
According to total number of entries or exits connected to the
valve through
which fluid can enter the valve or leave the valve there are
types like two way,
three way, four way valves.
• Number of Positions
Including the normal and working positions which a valve spool
can take there
are types like two position, three position and proportional
valves.
77
Ports labels in the directional control valves
35. • The pressure port is designated P and the return port R
or T (for tank). The two other ports are designated A
and B. Also, you can use numbers to label the ports, the
pressure port is numbered (1) and the exhaust port (3).
The other two are numbered (2) and (4)
78
3/2-way valve
• The 3/2-way valve has
working port A, a supply
port P and a tank port T.
Volumetric flow can be
routed from the supply port
to the working port or from
the working port to the tank
port. The third port in each
case is closed. In the normal
position shown, P is closed
and flow released from A to
T.
79
3/2-way valve
• The 3/2-way valve is
actuated; flow is
released from P to A,
the outlet T is closed.
36. • 3/2-way valves which
are normally open from
P to A and T closed are
also available.
80
3/2-way valve (Animation)
• The animations show
the actuation and
release of the manual
pushbutton for a 3/2-
way valve, which causes
the piston rod of the
cylinder to advance and
retract.
81
3/2-way valve as final control
element
• The circuit shows the 3/2-
way valve in a functional
representation as a final
control element of a single
acting cylinder.
• The non-return valve
protects the pump in cases
37. where the 3/2-way valve is
actuated and the piston rod
is subject to an external
load.
82
3/2-way valve (Animation)
83
Circuit diagram: 3/2-way valve as
final control element
• The illustration shows
the same circuit as the
previous illustration,
but with the circuit
symbol for the 3/2-way
valve.
84
3/2-way valve (Animation)
85
3/2-way valve
38. • The 3/2-way valve has a
working port A, a supply
port P and a tank port T.
The volumetric flow can be
routed from the supply port
to the working port, or from
the working port to the tank
port. The third port in each
case is closed. In the normal
position shown, P is closed
and flow is released from A
to T.
86
3/2-way valve
• The 3/2-way valve is
actuated; flow is
released from P to A,
and the outlet T is
closed.
• 3/2-way valves which
are normally closed
from P to A and T are
also available.
87
3/2-way valves as diverter
39. • In addition to their application
as final control elements, 3/2-
way valves can also be used as
diverters. In this case, port T is
connected to a further device,
to which a switch-over can then
be made. The part circuit
diagrams show the facility to
switch between the flow
control valves with different
settings and between heating
and cooling.
• The circuit symbol is drawn
reversed to simplify the
representation of the circuit
diagram.
88
4/2-way valve
• The 4/2-way valve has two
working ports A and B, a supply
port P and a tank port T. The
supply port is always connected
to one of the working ports,
while the second working port
is routed to the tank. In the
normal position, there is flow
from P to B and from A to T.
• In contrast to valves with three
40. pistons, 4/2-way valves with
two pistons do not require a
leakage-oil port (see topic 74).
89
4/2-way valve
• The 4/2-way valve is
actuated, and there is
flow from P to A and
from B to T.
• 4/2-way valves are also
available which are
normally open from P
to A and from B to T.
90
4/2-way valve
• This 4/2-way valve has two
working ports A and B, a supply
port P and a tank port T. The
supply port is always connected
to one of the working ports,
while the second working port
is routed to the tank. In the
neutral position, there is flow
from P to B and from A to T.
41. • 4/2-way valves with three
pistons require a leakage-oil
port, since hydraulic fluid
would otherwise be trapped
within the valve.
91
4/2-way valve
• The 4/2-way valve is
actuated, and there is
flow from P to A and
from B to T.
92
4/2-way valve
• The circuit shows the
4/2-way valve in
functional representation
as a final control element
of a double acting
cylinder.
• The non-return valve
protects the pump in
cases where the piston
rod of the cylinder is
subject to an external
42. load.
93
Circuit diagram: 4/2-way valve
• The illustration
shows the same
circuit as the
previous illustration,
but with the 4/2-way
valve as a circuit
symbol.
94
4/3-way valve with pump bypass
• From the logic point of view,
4/3-way valves are 4/2- way
valves with an additional mid-
position. There are various
versions of this mid-position (in
the mid-position in the example
shown, the supply port P is
directly connected to the tank
T, see next illustration). In the
switching position shown, there
is flow from P to B and from A
to T.
43. • 4/3-way valves are easy to
construct as slide valves and of
complex design as poppet
valves.
95
4/3-way valve with pump bypass
• The 4/3-way valve is in its mid-
position; there is flow from P
to T, while A and B are closed.
Since the output from the
pump flows to the tank, this
switching position is called
pump bypass or also pump
recirculation.
• In the case of pump bypass,
the pump needs to operate
only against the resistance of
the valve, which has a
favorable effect on the power
balance.
96
4/3-way valve with pump bypass
• The valve is in its left-
hand switching
44. position; there is flow
from P to A and from B
to T.
97
4/3-way valve with pump
bypass (Animation)
• The animations show the
switching of the 4/3-way
valve into the three switching
positions and the
corresponding cylinder
movements. During the
advance stroke, movement
can be halted by switching to
the mid- position.
• As appropriate to the
application in question, a
circuit of this kind must be
equipped with a brake valve
to prevent damage to the
installation when the valve is
switched to the mid-position.
98
4/3-way valve with pump bypass
45. • The circuit shows the 4/3-way
valve in functional
representation as a final
control element of a double
acting cylinder. The valve is in
its mid-position; the pump
delivery flows via the by-pass
line within the pilot piston to
the tank.
• The non-return valve protects
the pump in cases where the
piston rod of the cylinder is
subject to an external load.
99
4/3-way valve with pump bypass
(Animation)
100
Circuit diagram: 4/3-way valve
with pump bypass
• The illustration shows
the same circuit as the
previous illustration,
but with the 4/3-way
valve as a circuit
symbol.
46. 101
4/3-way valve with pump bypass
(Animation)
102
4/3-way valve with pump bypass
(Animation)
103
4/3-way valve with pump bypass
(Animation)
104
4/3-way valve with pump bypass
(Animation)
105
4/3-way valve with closed mid-
position
• From the logic point of
47. view, 4/3-way valves are
4/2- way valves with an
additional mid-position.
There are various
versions of this mid-
position (in the mid-
position in the example
shown, all ports are
closed in the mid-
position, see next
illustration). In the
switching position shown,
there is flow from P to B
and from A to T.
106
4/3-way valve with closed mid-
position
• The 4/3-way valve is in
its mid-position; all
ports apart from the
leakage-oil port are
closed.
• In this mid-position, the
pump is operating
against the system
pressure set on the
pressure relief valve.
107
48. 4/3-way valve with closed mid-
position
• The valve is in its left-
hand switching
position; there is flow
from P to A and from B
to T.
108
4/3-way valve with closed mid-
position
• The circuit shows the 4/3-way
valve in functional
representation as a final control
element of a double acting
cylinder. The valve is in its mid-
position; the pump is operating
against the system pressure set
on the PRV.
• If, with an operational
installation, it is desired to
switch to pump recirculation,
this can be achieved by using
an additional 2/2-way valve as a
changeover valve
49. 109
Circuit diagram: 4/3-way valve
with closed mid-position
• The illustration shows
the same circuit as the
previous illustration,
but with the 4/3-way
valve as a circuit
symbol.
110
4/3-way valve: overlap positions
• The illustration shows the left-
hand overlap position of a 4/3-
way valve with positive overlap
in the mid-position (closed mid-
position). This overlap position
is a mixture of positive and
negative overlap; P is
connected to A, B and T are
closed.
• With 4/3-way valves, the types
of overlap positions is generally
specified in the data sheet.
111
50. 4/3-way valve: overlap positions
• The illustration shows the
“right-hand” overlap
position of a 4/3-way valve
with positive overlap in the
mid- position (closed mid-
position). This overlap
position, too, is a mixture
of positive and negative
overlap; P is connected to
B, A and T are closed.
112
Directional control valve
• Actual photograph of a
directional control valve
with lever actuation.
113
4/3-way module
• This 4/3-way module
with hand-lever
actuation is used in
vertical interconnection
52. 118
Non-return valve
• Non-return valves block flow
in one direction and allow free
flow in the other. In the
direction of flow shown, the
sealing element is pressed
against a seat by a spring and
the hydraulic fluid.
• These valves are also available
in designs without springs.
Since there must be no leaks
in the closed position, these
valves are generally of poppet
design.
119
Non-return valve
• In the direction of
flow shown, the
valve is opened by
the hydraulic fluid,
which lifts the
sealing element
from the seat.
53. 120
Circuit diagram: Pump
protection
• In this circuit, the non-
return valve is used to
protect the pump. This
prevents a load pressure
from driving the pump in
reverse when the electric
motor is switched off.
Pressure peaks do not
affect the pump but are
discharged via the pressure
relief valve.
121
• Pump Protection using
Non-return valve
122
123
54. Flow Control Valve
124
Flow control
Valve
125
• One way Flow control
Valve
126
Control the
cylinder
speed in
both
55. directions
127
It may required high
force to actuate the
directional control
valve . For that a
manual switch
(similar to the
directional control
valves) have been
used to actuate the
directional control
valve ,with less force
128
OR / Shuttle Valve
Activated when
any of its sides
activated
129
AND/Dual Pressure Line
56. Activated
when both of
its sides
activated
130
131
Conductors/Pipe
• Steel pipe is commonly used as a fluid conductor when
large volumes of fluid are involved, or where its lower
cost relative to tubing is a factor.
• For general hydraulic purposes, seamless carbon steel
pipe is recommended. It must be free from dirt, rust ,
scale and any machine debris before being installed into
any hydraulic system.
• Standard finish given to steel pipe is a lacquer coating
that is intended to prevent corrosion during shipping and
storage. This is referred to as “black iron pipe. Best is
57. pickled and oiled or just pickled only. Galvanized pipe
should never be used on pressure lines it is accepted on
return lines
132
• If we double the size of the conductor we
quadruple the area and the flow will be
quartered
• When changing conductors pay particular
attention to size
133
Examples: Crane
• Hydraulic motors
have been used in
the hydraulic
cranes.
• In these cranes
metallic rope is
used to carry the
heavy loads. Draw
the hydraulic
circuit required
59. Look to the
following hydraulic
circuit ?. Also , try
to find how its
work and what are
the main
components in this
circuit ?
Hydraulic conductors
• Steel pipe
• Flexible hoses
137
Input and output power
• Various losses occur at the
individual devices within a
hydraulic control chain.
These consist essentially of
mechanical, electrical and
volumetric losses.
• After an installation has
60. been in service for some
time, there will be a change
in particular in the
volumetric efficiency of the
pump, as the result, for
example, of cavitation
138
139
Hydraulic circuit drawing using
AUTOCAD
140
AutoCAD is one the best software's that you can use to draw
the hydraulic circuits.
You have three different methods to that. The firstly you can
draw all of the hydraulic
symbols manually. Its good way but let use the other methods.
The second method
depend on the AutoCAD design center tool. This is a build in
library and inside it you
Can find different types of symbols. The following figures show
you how to use it.
61. Click on Insert
Then click on the
Design Center icon
141
Click on DesignCenter
Then click on
Hydraulic
Pneumatic icon
142
Then click on the required
symbol and drag it to the
AutoCAD screen
Unfortunately, you cannot find all hydraulic components in the
last method. There is external AutoCAD libraries that you can
use with AutoCAD. Just extract the symbols library on your
desktop. After that you can insert these symbols inside the
AutoCAD screen.
62. 143
144
Click on insert, then Block.
After that the AutoCAD ask
you to browse to the
required symbol file.
145
All symbols' that we
have here in this
library were saved as
DXF files. For that ,
you have to change
the File of type to
DXF. After that you
can see the symbols.
63. Just click on the
symbol then open
then OK.
After that you can
place the symbol in
the required position.
You may need to make zoom for
the AutoCAD screen
146
The basic calculations in the Hydraulic systems
147
148
65. 157
158
159
160
Other applications
Circuit without brake valve
(Animation)
• One application of pressure relief
valves is as brake valves; these
prevent pressure peaks which
may otherwise occur as the result
of mass moments of inertia when
a directional control valve is
suddenly closed. The animation
shows an (incorrect) circuit in
schematic form in which the
working line on the exhaust side
66. has fractured due to the absence
of a brake valve.
• The next animation shows the
correct circuit.
161
Circuit without brake valve
(Animation)
162
Circuit without brake valve
(Animation)
163
Circuit without brake valve
(Animation)
164
Circuit without brake valve
(Animation)
165
67. Circuit diagram: Brake valve
• This circuit incorporates not
only a brake valve on the
piston-rod side but also a
non-return valve on the
inlet side via which oil can
be taken in from a reservoir
during the vacuum phase
following the closure of the
directional control valve.
• The following animation
shows the events which
occur in the two working
lines.
166
Circuit with brake valve
(Animation)
• The necessity of the
brake valve can be
demonstrated by the
preceding animation.
167
68. Circuit with brake valve
(Animation)
168
Circuit with brake valve
(Animation)
169
Circuit diagram: PRV as back-
pressure valve
• Back-pressure valves
counteract mass moments
of inertia with tractive
loads. The illustration shows
a circuit with a back-
pressure valve on the
piston-rod side. On the
return stroke, the PRV is by-
passed by an NRV.
• The PRV must be pressure-
compensated and the tank
port must be capable of
carrying a pressure load.
170
69. Sequence valve
• The example shows a circuit
with a pressure relief valve
used as a pressure
sequence valve. The
pressure at the pilot piston
of the PRV rises via the
pressure regulator. The PRV
opens and the high-
pressure pump delivers
directly to the tank. As soon
as the 2/2-way valve opens,
the pressure drops. The
pressure relief valve closes
and the high pressure pump
is connected to the system. 171
Circuit diagram: Sequence valve
• This illustration shows
the same circuit as the
previous illustration,
but with the cut-away
view of the sequence
valve replaced by the
appropriate circuit
symbol.
172
70. 10 - *
Chapter 10
Buying and Disposing
By Michael R. Solomon
Consumer Behavior
Buying, Having, and Being
Sixth Edition
10 - *
Opening Vignette: RobWhat kind of background research did
Rob do on the car?What preconceptions did Rob have about his
ability to negotiate the deal?What were Rob’s perceptions about
the salesperson?Why did Rob feel that he negotiated well when
he paid more than he expected?
10 - *
Autobytel
10 - *
Situational Effects on
Consumer BehaviorConsumption Situation:Factors beyond
characteristics of the person and of the product that influence
71. the buying and/or using of products and servicesSituational
Self-Image:The role a person plays at any one time.
10 - *
Purchase and Postpurchase Issues
Figure 10.1
10 - *
Situation Influences ChoiceClothing choices often are heavily
influenced by the situation in which they need to be worn.
10 - *
Social and Physical SurroundingsCo-consumers:Other patrons
in the settingDensityThe actual number of people occupying a
spaceCrowding:Exists only if a negative affective state occurs
as a results of densityTemporal Factors:Time Poverty: A
consumer’s feeling that he or she is pressed for time
10 - *
Physical EnvironmentsMany stores and services (like airlines)
try to differentiate themselves in terms of the physical
environments they offer, touting amenities such as comfort.
10 - *
72. Temporal FactorsEconomic Time:Time is an economic variable
(i.e., it is a resource that must be allocated)Time Poverty: A
consumer’s feeling that they are pressed for timePsychological
TimeTime Categories
Flow Time
Occasion Time
Deadline TimeLeisure Time
Time To Kill
10 - *
Time PovertyTime poverty is creating opportunities for many
new products (like portable soups) that let people multitask.
10 - *
Drawings of Time
Figure 10.2
10 - *
Psychological TimeLinear Separable Time:Events proceed in an
orderly sequence and different times are well
defined.Procedural Time:When people ignore the clock and do
things “when the time is right”Circular or Cyclic TimeTime is
73. governed by natural cyclesQueuing TheoryThe mathematical
study of waiting in lines
10 - *
Antecedent StatesIf It Feels Good, Buy It…Pleasure and
Arousal:Two dimensions which determine if a shopper will
react positively or negatively to a consumption
environmentMood:Some combination of pleasure and
arousalConsumers give more positive evaluations when they are
in a good moodCan be affected by store design, weather, or
other factors specific to the consumer
10 - *
Dimensions of Emotional States
Figure 10.3
10 - *
Shopping: A Job or An Adventure?Reasons for
Shopping:Shopping Orientation: General attitudes about
shoppingHedonic Shopping Motives:Social ExperiencesSharing
of Common InterestsInterpersonal AttractionInstant StatusThe
Thrill of the HuntE-Commerce: Clicks Versus Bricks
10 - *
Customizing at Covergirl
74. 10 - *
Pros and Cons of E-Commerce
10 - *
Discussion QuestionE-Commerce is changing the way people
shop. E-commerce sites like Bluefly give shoppers the option
of shopping without leaving home.What products do you not
feel comfortable buying online? Why?
10 - *
Retailing as TheaterRetail ThemingThe strategy of creating
imaginative environments that transport shoppers into fantasy
worlds or providing other kinds of stimulation.
Store ImageThe personality of a store including the store’s
location, merchandise suitability, and the knowledge and
congeniality of its sales staff.AtmosphericsThe “conscious
designing of space and its various dimensions to evoke certain
effects in buyers.”Landscape themes
Marketspace themesCyberspace themes
Mindscape themes
10 - *
75. FedEx Brand Position
Figure 10.4
10 - *
In-Store Decision MakingSpontaneous ShoppingUnplanned
buying: Occurs when a person is unfamiliar with a store’s
layout or when under some time pressure; or, a person may be
reminded to buy something by seeing itImpulse buying: Occurs
when the person experiences a sudden urge that cannot be
resistedImpulse items: Items conveniently placed near a
checkout
10 - *
Spontaneous ShoppingSmart retailers recognize that many
purchase decisions are made at the time the shopper is in the
store. That’s one reason why grocery carts sometimes resemble
billboards on wheels.
10 - *
One Consumer’s Image
of an Impulse Buyer
Figure 10.5
10 - *
76. Categorizing Shoppers
by Advance PlanningPlannersTend to know what products and
specific brands they will buy beforehand.Partial PlannersKnow
they need certain products, but do not decide on a specific
brand until they are in the storeImpulse PurchasersDo no
advance planning
10 - *
Point-of-Purchase StimuliPoint-of-Purchase Stimuli (POP)An
elaborate product display or demonstration, a coupon-
dispensing machine, or someone giving out free samplesSome
more dramatic POP displays:TimexKellogg’s Corn
FlakesElizabeth AllenTower RecordsTrifariCharminThe Farnam
Company
10 - *
Music SamplersMusic samplers that allow shoppers to check out
the latest music tunes before buying have become a fixture in
many stores.
10 - *
The SalespersonExchange Theory:Every interaction involves an
exchange of value.Commercial Friendships:When service
personnel and customers form relationshipsIdentity
Negotiation:A relationship in which some agreement must be
reached about the roles of each participantInteraction
Styles:Salespeople can adapt their approach according to
customer’s traits and preferences
77. 10 - *
Postpurchase SatisfactionConsumer satisfaction/dissatisfaction
(CS/D):Determined by the overall feelings, or attitude, a person
has about a product after it has been purchased.Perceptions of
Product Quality:Consumers use a number of cues to infer
qualityQuality Is What We Expect It To Be:Expectancy
Disconfirmation Model: Consumers form beliefs about product
performance based on prior experience with the product and/or
communications about the product that imply a certain level of
quality.Managing Expectations: Customer dissatisfaction is
usually due to expectations exceeding the company’s ability to
deliver.
10 - *
Quality PerceptionsThis ad for Ford relies on a common claim
about quality.
10 - *
Customer Expectation Zones
Figure 10.6
10 - *
Acting on DissatisfactionThree Possible Courses of
ActionVoice Response: The consumer can appeal directly to the
retailer for redress.Private Response: Express dissatisfaction
about the store or product to friends and/or boycott the
store.Third-Party Response: The consumer can take legal action
78. against the merchant, register a complaint with the Better
Business Bureau, or write a letter to the newspaper. TQM:
Going to the GembaGemba: The one true source of information.
10 - *
Going to the Gemba
Figure 10.7
10 - *
Planet Feedback
10 - *
Product DisposalDisposal Options:(1) Keep the item(2)
Temporarily Dispose of it(3) Permanently dispose of itLateral
Cycling: Junk Versus “Junque”Lateral Cycling: When already
purchased objects are sold to others or exchanged for other
things.Underground Economy: Secondary markets (e.g. eBay)
10 - *
Consumers’ Disposal Options
Figure 10.8
10 - *
VolkswagenThis Dutch ad says, “And when you’ve had enough
79. of it, we’ll clear it away nicely.”
10 - *
Discussion QuestionHow do secondary markets created by such
sites as eBay affect the sales of new goods from traditional
retailers? What can they do to compete with these products?
10 - *
Used CD’sThe used recording market is alive and well.
10 - *
ReDo
Australian College of Kuwait
School of Engineering
Department of Mechanical Engineering
Assignment 1: Set Up Basic Hydraulic Circuit
(Date 16/03/2015)
80. Student’s name & ID
Lecturer’s name
Date/Time/Location
Unit code & title W5262 - Set Up Basic Hydraulic Circuit
National number MEM30010A
School/Division School of Engineering / Mechanical
Engineering
Learning Outcomes
tested
1,2,3
Result: Demonstrated / Not Yet
Demonstrated
Feedback: Action Plan to Develop Skills:
Lecturer’s Signature: Date:
Student’s Signature: Date:
Design a full hydraulic system that can be used to control the
following lifting
81. mechanism? [30 marks]
Lifting device for heavy loads is equipped with two hydraulic
cylinders. In order
for this mechanism to operate correctly, the two cylinders
connected to the table
must both advance and return at the same speed. By clicking on
a certain pedal
the table will move up, and by clicking on another pedal the
table will move
down.
1) Prepare list of all parts required in this hydraulic system, and
justify your
selection for each component.
2) Draw the full hydraulic circuit by using AutoCAD showing
all parts and
connections.
3) Add any kind of practical improvement(s) on the hydraulic
circuit of this
mechanism, and justify it clearly to your instructor. Also, you
must show
the improvement(s) on the AutoCAD drawing.