This document provides instructions for producing different types of paint, including emulsion paint, textcoat paint, and satin or nylon paint. Emulsion paint is produced by mixing water, calcium carbonate, color pigments, PVA, thickeners like nitrosol and acrytext. Textcoat paint adds marble dust for texture. Satin paint is washable so it replaces PVA with additional acrytext and less calcium carbonate. Precise measurements and the order of adding ingredients is important for ensuring the proper properties and preventing issues like paint coagulation.

1. A COMPLETE GUIDE TO PRODUCTION OF PAINT
I sincerely welcome to this course. we shall be treating how to produce all kinds of paints
from emulsion, textcoat, and Satin otherwise called nylon or washable paint. lets get
started.
A COMPLETE GUIDE TO PAINT PRODUTION
Emulsion, Textcoat and Satin (nylon paint)
Introduction of chemical
These are the chemical to be used in the production of emulsion paint<br />
1. Water
2. Titherni (used only for the production of white paint)
3. Calcium carbonate (Calcium)
4. Colourite
5. P.V.A
6. Formalin
7. Nitrosol
8. Ammonia
9. Hydrosol
10. Marble dust
11. Acrydext
Others include
12. Geniple
13. K14
14. Bama cork
Functions of the chemicals
1. water
Water is used to mix all the chemicals together. It must not be a hot water. You can use
any type of clean and neat water with normal water temperature. However, I prefer soft
water to cold water. It helps to mix the paints more easily.
2. Titherni
It is whitening chemical in powdery form. You can always get it where they are selling
paint chemical, or rather industrial chemical. Just ask of titherni it will be given to you. It
performs the function of making sure that you with paint is shining and not dull. This is
the secret of some big names in painting industry. We shall give you the ratio down the
line. It is only used when you are producing with paint. That does not mean you cannot
use it in other colours but the function is more significant in white paints.
3. Calcium Carbonate
This chemical is also in powdery form. It is packaged in bags and they write CalCo on it.
It is made by so many companies, I would not like to advertise any but just ask of
calcium and it will be given to you.
Now calcium carbonate is of two or types
We have delomite and cacite. Both are good but delomite is recommended if you are
producing pure white paint and cacite is better in off white (dirty white) paint.
4. Colourite

2. This is the most important of the entire course. It involves the ability of mixing some
colours to get a desired result. It is not difficult at all if you have initiative and artistic
eye.
These are the colours we have in raw form ( please permit me to call them primary
colours because all other colours in the painting industry is gotten from them)
They are: yellow ( we painters call it cream), Red, Black, Blue, and Green. All other
colours are gotten from a combination of one or two of these.
What about White paint? You might ask. Well we do not need to have a pure white
colour because, we make our paints with CalCo and it gives us white naturally. In fact
once you put your calcium in water you get white paint. I hope that is clear.
We shall cover how to mix the paints to get particular result. But for now just know that
colours can be found in paste or oxide. When we say colours are in paste we mean that
they are in condensed liquid form (like your pomade), when they are in oxide it means
they are in dust form (like your wife’s powder). A colour like cream has both oxide and
paste. Red and black are mostly in oxide, green and Blue are in paste. For those who
might be wondering which one to use between the yellow oxide and yellow paste, I
suggest that if you want the colour you are producing to be deep yellow like MTN colour,
you should use paste, otherwise use oxide.
CAUTION: you MUST dilute the colours very well with a little water before you apply it
to your paint. For example if you get a red oxide, pour a cup of water in a different
container mix thoroughly. If not, your paint will be having dotted stains as you roll it on
the wall.
5. P.V.A.
This chemical is very important. I guess you might have seen a situation where after
painting a building, when you rub your hand on the surface it will be dusting. That is as a
result of ill usage of this liquid formed chemical. In my experience, some big names in
the painting industry do not even know how to use it. But you not worry, I will tell you
and who know you might become their next consultant.
6. Formalin
It does the function of preservative.
7. Nitrosol
It helps to hold the paints together i.e it is a thickener. Its correct usage makes the paint
more durable on the wall.
8. Ammonia
This is your secondary school laughing gas. It is also used to make the paints more
durable. It serves as a preservative agent too.
9. Hydrosol
This is the chemical that integrates the colours and brings out the best in them. It is used
to correct dullness in paints.
10. Marble dust
This is usually used in the production of textcoat paints. It is of two types rough and
smooth. The preference is determined by what you want to achieve. If you want sandy
textcoat i.e the one without lining, you use only rough type. However, the combination of
both in the same ratio gives a better result.
11. Acrytext
This is used as a thickener. It holds the seemingly watery paint together.

3. 12. Geniple
This one just does the function of giving the painter a scintillating perfume as he does his
job.
12. K14
It is also a preservative.
13. Bama cork
It does the function of nitrosol. If you use bama cork you do not need to use nitrosol.
Steps to making Emulsion Paints
Emulsion are those ordinary paints that are not roughened with sand-like objects. The
once that are sand-like are regarded as textcoat. You need to aware that there are other
types of paint as well. Satin, oil e.t.c we shall treat them separately but for now let us
concentrate with textcoat and emulsion.
For emulsion
Step 1.
Mix Calcuim Carbonate in water
For one bucket production (hence we shall be referring to bucket of paint i.e. normal --
litres of paint as drum), pour water in the bucket up to half (-- liters of water) you can
always increase the volume of water at any stage if necessary. Add less than half bag of
Calcuim (add until the mixture rises to about 17 liters in the bucket) by now the drum
will be quarter empty. NOTE; if you are producing white paint, you will mix titherni in
water before adding calcium. -- spoons of titherni are enough. MIX VERY WELL.
Step 2:
Add your colour. It is assumed that by now you must have diluted the colours as required
with water if they are oxide. Now put colour in small rations and keep turning until you
get your desired result. You can always add more if you like. Suppose you added more
yellow for example, than you need, you can correct it by adding more calcium (but not
after this stage) Bear in mind that the colour may be deeper when wet and lighter when
the paint is dried.
Step 3
Add --kg of P.V.A to the mixture. After turning add half glass cup of nitrosol. Nitrosol is
always in powdery form so you must dilute it in small water before you add to your
mixture.
Next add about -- centiliter of formalin and about same volume for ammonia and
hydrosol sequentially. Turn very well at any addition of a new chemical.
Final step
When you have completed the above steps, make sure that you turn the above mixture
very well. As you are turning it you might be a little fidgeted that you have wasted your
resources. You don’t need to be afraid. Just add acrytext to the mixture and turn. Add it in
small quantity until you get the thickness you desire. However if you add access you
might spoil your mixture. Now that you paint is ready, just take your scraper, brush and
roller and roll away your newly built house.
Warning: please the chemicals must be added in the order I have given you. If not you
may have problem for example if you put ammonia before Nitrosol, the paint will get
blocked. And again if ammonia drops in Nitrosol, the Nitrosol will block. More so, when

4. formalin is poured into ammonia it will explode. The only time you can add ammonia
before Nitrosol is when you are turning on machine speed. Just be careful.
For Large Quantity Production
If we are working wit 350 litres of butter, we shall have about 16 drums of paint after
production.
Now 350 litres butter goes with -- litres of water i.e. pour -- and half paint buckets of
water
Add -- bags of Calcium
1kg of titherni(if you a producing white paint)
-- kg of P.V.A (for super quality paint or --kg for less quality paint)
-- kg of Nitrosol
Others has no specific quantity. You just add with discretion but make sure you do not
over add especially Acrytext.
Production of Textcoat
For 1 drum of textcoat
Step 1:
Pour about -- liters of water into the bucket, add -- bag of Calcuim (or less) then add your
colours as it is supposed to be.
Step 2: now after turning the mixture above, you add marble dust( I hope you remember
what we said about marble dust above). Good. You will notice that some textcoat paints
have a kind of lining and some has only rough surface. And there are those that we call
designer textcoat such are the once that they use with the aid of a special roller to design
houses so that its end effect will be something like flowers or blocks made of paint in
your house. Am sure you must have seen such paint. It is called artwork in the painting
industry. All these are textcoat but it is the mode of application of this chemical that
makes different types.
For rough textcoats use only rough marble dust in your production
For lining textcoats use a combination of rough and smooth marble dust in equal ratio( if
you are producing this one I will advice you add smooth marble dust first after turning
add the rough one)
For artwork textcoats use only smooth marble dust in production.
Now as you are adding the marble dust, you will notice that the volume of your mixture
is increasing. Just add according to your own discretion it has no specific measurement. If
you are confused on the quantity to add, just keep adding until the drum is -- empty. Use
your initiative. Please do not use only smooth marble dust for production unless you are
producing artwork that needs a designer roller.
Step 3: when you are through with turning of this mixture (turn very well), you will now
add your P.V.A. and other chemicals like we said in emulsion. However you will need to
increase their volume a little. For example you will need full glass cup of Nitrosol and
increase the volume of other chemicals a little. When you have finish adding all the other

5. chemical up to Hydrosol, you can go and gym in order to activate your muscle for
turning the paint as you add Acrytext. On the addition of acritext the paint will become
strong. Now to know if the Acrytext you added is enough, take a small portion of the
paint and touch it on the wall. If the teething is not falling congratulations if it is falling
add more. Now you can go and roll away your textcoat on your parlour.
Bigger Quantity Production
350 litre butter will give us 15 drums of textcoat paint
Add -- drums of water ( remember what we said about drum)
Use -- bags of calcium
Use -- bag of marble Dust i.e. -- for rough, -- for smooth
Empty -- kg of Nitrosol and -- kg of P.V.A
All other are as usual
If you cannot turn the whole paint when you add acrytext, pour them out in different
buckets and add you acrytext so that you can turn it.
When this is done call your marketer and take the latest product to the hungry market.
Satin (nylon paint)
I hope you remember we did mention Satin paint some where. This is the type of paint
that is generally regarded as nylon paint. It is called nylon paint because it is washable ( u
can use water to wash it when it is dirty.
Production of Satin
For one drum
Use About -- litres of water. Add calcium in a small quantity to make the paint light.
What I mean is that the thickness of the paint at this stage will be less than the thickness
it has when we are producing emulsion.
Now add your favourite colour.
You do NOT use P.V.A.
Add -- kg of Acritext
-- kg of Nitrosol (just enough to make the paint thicker and drawing)
Add ammonia and formalin as usual and finally add -- kg of hydrosol
Your washable paint is ready. Beautify your house.
Thank you.
i hope i have given enough information to you if you really want to get the rations i.e
where i placed --, pay the sum of N2000 to the following

6. chemical up to Hydrosol, you can go and gym in order to activate your muscle for
turning the paint as you add Acrytext. On the addition of acritext the paint will become
strong. Now to know if the Acrytext you added is enough, take a small portion of the
paint and touch it on the wall. If the teething is not falling congratulations if it is falling
add more. Now you can go and roll away your textcoat on your parlour.
Bigger Quantity Production
350 litre butter will give us 15 drums of textcoat paint
Add -- drums of water ( remember what we said about drum)
Use -- bags of calcium
Use -- bag of marble Dust i.e. -- for rough, -- for smooth
Empty -- kg of Nitrosol and -- kg of P.V.A
All other are as usual
If you cannot turn the whole paint when you add acrytext, pour them out in different
buckets and add you acrytext so that you can turn it.
When this is done call your marketer and take the latest product to the hungry market.
Satin (nylon paint)
I hope you remember we did mention Satin paint some where. This is the type of paint
that is generally regarded as nylon paint. It is called nylon paint because it is washable ( u
can use water to wash it when it is dirty.
Production of Satin
For one drum
Use About -- litres of water. Add calcium in a small quantity to make the paint light.
What I mean is that the thickness of the paint at this stage will be less than the thickness
it has when we are producing emulsion.
Now add your favourite colour.
You do NOT use P.V.A.
Add -- kg of Acritext
-- kg of Nitrosol (just enough to make the paint thicker and drawing)
Add ammonia and formalin as usual and finally add -- kg of hydrosol
Your washable paint is ready. Beautify your house.
Thank you.
i hope i have given enough information to you if you really want to get the rations i.e
where i placed --, pay the sum of N2000 to the following