Process selection
โขDownload as PPTX, PDFโข
0 likesโข150 views
The document outlines the processes and costs for producing a prototype part using a plaster of Paris mold. The primary process is crafting the mold and prototype pattern. The secondary process injects resin into the mold to create the part. The tertiary process finishes the surface and applies paint. The total first time cost is 198.1 Baht, including the mold, raw materials, wood pattern, and labor/tools. Subsequent parts cost 113.1 Baht each without needing to remake the mold.
Report
Share
Report
Share
Recommended
Week 5
The document summarizes the manufacturing process, material selection, and cost analysis for a bamboo furniture product. The primary process is sawing, secondary is drilling and pushing, and tertiary is lacquering. Bamboo and eucalyptus wood were selected for their compatibility with cutting, drilling, and ability to withstand typical loads of 0.02-1.6 kg. The manufacturing costs were calculated based on material, time, and process costs for each component - top body, low body, legs, and branches - totaling 79.016 baht per part.
Rate analysis
This document provides an analysis of rates for various civil engineering works including excavation, sand filling, brick masonry, concrete works, and reinforced cement concrete works. It includes calculations of quantities of materials required and rates analysis for a unit quantity (typically 1 cubic meter or 10 cubic meters) with breakdown of material and labor costs. Factors affecting rates and data required for rate analysis are also discussed.
ACT 333__Cost accounting report on fountain
This document is a group project report submitted to a lecturer for an accounting course. It provides details on analyzing the costs of producing a customized indoor fountain product. It discusses the manufacturing process, direct materials and labor costs, manufacturing overhead costs, support and selling costs, costing methods like simple costing and activity-based costing, budgets, break-even analysis, and a profitability comparison. The group focused on costing and pricing strategies for the fountain product as required by the course guidelines.
Week5
The document summarizes the manufacturing process for a wood product. The primary process is cutting wood parts, the secondary process is drilling holes for nuts, and the tertiary process is painting. The material and processes are compatible with the product geometry. The total cost per part was calculated to be 174 Thai Baht using formulas that summed material, tooling, and production costs.
Making the Move to Closed Moulding Processes
The document discusses alternative composite materials processing methods for boat building, including hand layup, resin infusion, and resin film infusion. Resin infusion offers the lowest structural weight at 56.1% of current methods and lower labor costs, but higher material costs. Resin film infusion has the lowest structural weight at 49.8% but much higher material and total costs. While pre-pregs have high costs, developments may make them more affordable. The learning curve is steep, so seeking help from experts and practicing small sections is recommended before full implementation.
Act 333
1. The document is a project report submitted by a group of students on applying managerial accounting concepts to product costing of sandals.
2. It includes an analysis of manufacturing process, estimated costs including direct material, direct labor, manufacturing overhead. It also classifies costs as variable and fixed.
3. The group estimates production capacity, calculates cost per unit using simple costing and activity based costing, and analyzes profitability using income statement in traditional and contribution format.
Assignment ceiling finishes
The document estimates the costs of installing a plasterboard ceiling and painting a plaster surface.
For the ceiling: The material cost is estimated at RM17.14 per square meter including plasterboard, battens, and 10% wastage. Labour costs RM24.38 per square meter. The total estimated cost is RM47.75 per square meter including 10% profit and 5% overhead.
For painting: The material cost is estimated at RM285.96 per 100 square meters including undercoat, two finishing coats, and 10% wastage. Labour costs RM148 per 100 square meters. The total estimated cost is RM564.83 per 100 square meters or RM5.65 per square meter including 20%
Analysis of rates
This Presentation will give you brief idea about analysis of rates and schedule of rates like its definition, need, method etc.
Recommended
Week 5
The document summarizes the manufacturing process, material selection, and cost analysis for a bamboo furniture product. The primary process is sawing, secondary is drilling and pushing, and tertiary is lacquering. Bamboo and eucalyptus wood were selected for their compatibility with cutting, drilling, and ability to withstand typical loads of 0.02-1.6 kg. The manufacturing costs were calculated based on material, time, and process costs for each component - top body, low body, legs, and branches - totaling 79.016 baht per part.
Rate analysis
This document provides an analysis of rates for various civil engineering works including excavation, sand filling, brick masonry, concrete works, and reinforced cement concrete works. It includes calculations of quantities of materials required and rates analysis for a unit quantity (typically 1 cubic meter or 10 cubic meters) with breakdown of material and labor costs. Factors affecting rates and data required for rate analysis are also discussed.
ACT 333__Cost accounting report on fountain
This document is a group project report submitted to a lecturer for an accounting course. It provides details on analyzing the costs of producing a customized indoor fountain product. It discusses the manufacturing process, direct materials and labor costs, manufacturing overhead costs, support and selling costs, costing methods like simple costing and activity-based costing, budgets, break-even analysis, and a profitability comparison. The group focused on costing and pricing strategies for the fountain product as required by the course guidelines.
Week5
The document summarizes the manufacturing process for a wood product. The primary process is cutting wood parts, the secondary process is drilling holes for nuts, and the tertiary process is painting. The material and processes are compatible with the product geometry. The total cost per part was calculated to be 174 Thai Baht using formulas that summed material, tooling, and production costs.
Making the Move to Closed Moulding Processes
The document discusses alternative composite materials processing methods for boat building, including hand layup, resin infusion, and resin film infusion. Resin infusion offers the lowest structural weight at 56.1% of current methods and lower labor costs, but higher material costs. Resin film infusion has the lowest structural weight at 49.8% but much higher material and total costs. While pre-pregs have high costs, developments may make them more affordable. The learning curve is steep, so seeking help from experts and practicing small sections is recommended before full implementation.
Act 333
1. The document is a project report submitted by a group of students on applying managerial accounting concepts to product costing of sandals.
2. It includes an analysis of manufacturing process, estimated costs including direct material, direct labor, manufacturing overhead. It also classifies costs as variable and fixed.
3. The group estimates production capacity, calculates cost per unit using simple costing and activity based costing, and analyzes profitability using income statement in traditional and contribution format.
Assignment ceiling finishes
The document estimates the costs of installing a plasterboard ceiling and painting a plaster surface.
For the ceiling: The material cost is estimated at RM17.14 per square meter including plasterboard, battens, and 10% wastage. Labour costs RM24.38 per square meter. The total estimated cost is RM47.75 per square meter including 10% profit and 5% overhead.
For painting: The material cost is estimated at RM285.96 per 100 square meters including undercoat, two finishing coats, and 10% wastage. Labour costs RM148 per 100 square meters. The total estimated cost is RM564.83 per 100 square meters or RM5.65 per square meter including 20%
Analysis of rates
This Presentation will give you brief idea about analysis of rates and schedule of rates like its definition, need, method etc.
Int. ceiling finishes
The document provides a cost estimate for plasterboard ceiling and painting internal ceilings. It estimates the material and labor costs to install 12.5mm thick fibrous plaster ceiling at RM32.10/m2 including plasterboard, battens, labor for installation, profit, and overhead. It also estimates the material and labor costs to apply undercoat and two finishing coats of paint at RM3.18/m2 including paint, labor for application, tools, profit, and overhead. The total cost per square meter for ceiling finishes is estimated to be RM32.10/m2 for installation and RM3.18/m2 for painting.
A clam electrical outlet
The document discusses the manufacturing process and costs for injection molding 10,000 plastic parts per week. It covers:
1) Injection molding as the primary process due to its high production rates, design flexibility, repeatability, ability to process many materials, and low labor costs.
2) Secondary processes like trimming and drilling.
3) Tertiary painting process.
4) Material and manufacturing process compatibility.
5) A total cost per part of 96.55 Baht including material, tooling, and processing costs for the injection molded plastic parts.
Presentation slide of act 333 final
This document summarizes the costing and budgeting for sandal production. It includes analysis of direct material costs, direct labor costs, manufacturing overhead costs, and allocation of overhead. Budgets are presented for production, direct materials, direct labor, cost of goods sold, income statement, contribution margin, break-even point, margin of safety, and sensitivity analysis. The objective is to apply managerial accounting concepts to determine the full cost of each sandal and budget costs and profits.
rate analysis
The analysis of rates is determining the cost per unit of an item of work based on materials, labor, and other expenses. It involves calculating the costs of materials and labor, which vary by location, and determining the actual cost per unit. This is used to calculate the costs of extra work, revise rates due to cost changes, and ensure economical use of materials and processes. Factors that influence the analysis include material and labor costs, equipment, work conditions, specifications, and contractor profit.
Week 5
The primary manufacturing process for the shoes is casting because the switch is made of plastic and the globe is made of resin, which are suited for casting. The secondary process is drilling to fix the electrical circuit to the sole. The tertiary process is joining and painting - joining to connect the wire and assemble to the sole, and painting to make the shoes trendy. The material and manufacturing processes are compatible with the product geometry. The electrical circuit size suits the sole base and shoes can be different sizes. The material can withstand the normal load of a person's foot weight and be kept away from direct sunlight or water.
Fundamentals of Estimating and Costing
The document discusses the process of estimating for construction projects. It explains that estimates are needed to determine the approximate quantities of materials and labor costs required. There are different types of estimates including approximate estimates which provide an initial cost, and detailed estimates which provide a cost closer to the actual amount. Various methods are described for calculating estimates along with the units of measurement used. Record keeping forms like measurement sheets and abstract sheets are used to document the estimated costs.
Bamboo special
The document discusses various manufacturing processes and considerations for selecting processes for a product. It addresses choosing a primary, secondary and tertiary process based on the product's function, material compatibility, load requirements and ambient conditions. It also provides a calculation for determining the total manufacturing cost per part by summing the costs of material, tooling and processing. The cost factors include material price, waste percentage, number of parts per run, machine rate, labor costs and cycle time.
Bamboo special
The document discusses various manufacturing processes and considerations for selecting processes for a product. It addresses choosing a primary, secondary and tertiary process based on the product's function, material compatibility, load requirements and ambient conditions. It also provides a calculation for determining the total manufacturing cost per part by summing the costs of material, tooling and processing. The cost factors include material price, waste percentage, number of parts per run, machine rate, labor costs and cycle time.
Cost accounting project
The document summarizes the costs of three products (X, Y, Z) for a company using different costing methods. Under direct labor hour allocation of overheads, product X costs Rs. 61, product Y costs Rs. 74, and product Z costs Rs. 38. Using machine hours and material handling for overhead allocation, the costs are Rs. 66.54, Rs. 57.62, and Rs. 58.05 respectively. Activity based costing allocates overheads based on cost drivers and calculates the costs as Rs. 53.31, Rs. 50.07, and Rs. 126.65 respectively. The differences in product costs are due to the different allocation methods used for overhead costs.
Break even-point
This document discusses break-even analysis for three companies. Break-even analysis is used to predict when a business will start making a profit by determining the sales volume needed to cover total costs. It provides the break-even point in units and sales for each company. Company 1 produces bricks and has a break-even point of 10,000 units or Rs. 80,000 in sales. Company 2 produces concrete and has a break-even point of 400 tons or Rs. 333,200 in sales. Company 3 manufactures windows and doors and has a break-even point of 900 units or Rs. 162,000 in sales.
Estimation of wall
The document provides an example to calculate the quantities and costs of brickwork and plastering for a wall that is 4m long, 3m high and 30cm thick. It determines that the quantity of brickwork is 3.6 cubic meters at a rate of Rs. 320/cum, costing Rs. 1152. The quantity of plastering is 24 square meters at a rate of Rs. 8.50/sqm, costing Rs. 204. The total cost of the brickwork and plastering is Rs. 1356.
Costsheet final
This document provides a cost sheet analysis for a ladies clothing manufacturer. It includes details of direct costs like materials consumed and wages. It also lists factory overheads like handwork and coloring. Office overheads such as electricity are included. Sales and distribution overheads such as salesman salaries and commissions are specified. Calculations for prime cost, factory cost, cost of production and total cost are demonstrated. The cost sheet shows total sales of Rs. 911,000 with a net profit of Rs. 61,000, which is 6.70% of sales. In summary, the document presents a cost analysis for a clothing company through a detailed cost sheet.
Rate analysis vansheika
This document provides a rate analysis for 10 cubic meters of reinforced cement concrete (RCC) slab with a mix ratio of 1:2:4.
The rate analysis calculates costs for materials, labor, equipment rental, water charges, and contractor profit. Material costs include cement, sand, coarse aggregate, and steel reinforcement. Labor costs account for masons for mixing, transporting, placing, binding, and shuttering.
The total cost is Rs. 84,996, to which water charges of 1.5% and 10% contractor profit are added. The final rate calculated per cubic meter of RCC slab is Rs. 9,477.
Takiantong group
The main manufacturing processes are cutting, drilling, and painting. Cutting is used to separate the plastic bottle into 3 parts that are assembled. Drilling makes holes to attract flies to the light. Painting in black further draws flies into the holes and lamp.
Cost sheet ppt
The document discusses the components and computation of a cost sheet. It explains that a cost sheet tracks direct material costs, direct labor costs, direct expenses, factory/works overhead costs, office and administration overhead costs, and selling and distribution overhead costs. It provides a template for a cost sheet showing accounts for materials consumed, direct labor, prime costs, factory costs, production costs, cost of goods sold, and sales. It then provides an example cost sheet with specific costs to populate the template for a company.
Jet engine 2nd prototype
The project's second prototype requires extending the mold creation duration to improve quality and being more careful when ejecting work pieces from the mold. Leaks around the mold should also be identified before pouring resin. Key factors to consider include quality, weight, ease of use, manufacturing time, and cost.
Process selection
This document describes the 5-step process for manufacturing jet engines, including wood sculpting, mold creation, resin forming, trimming and drilling, and painting. The current process has workers manually transferring parts between each step, which could be improved for efficiency.
Material selection - Jet Engine
This document discusses three factors related to material selection: Young's Modulus and cost, strength compared to maximum service temperature, and recycle fraction and cost. It considers the tradeoffs between mechanical properties, operating conditions, sustainability, and financial costs for choosing the right material.
More Related Content
What's hot
Int. ceiling finishes
The document provides a cost estimate for plasterboard ceiling and painting internal ceilings. It estimates the material and labor costs to install 12.5mm thick fibrous plaster ceiling at RM32.10/m2 including plasterboard, battens, labor for installation, profit, and overhead. It also estimates the material and labor costs to apply undercoat and two finishing coats of paint at RM3.18/m2 including paint, labor for application, tools, profit, and overhead. The total cost per square meter for ceiling finishes is estimated to be RM32.10/m2 for installation and RM3.18/m2 for painting.
A clam electrical outlet
The document discusses the manufacturing process and costs for injection molding 10,000 plastic parts per week. It covers:
1) Injection molding as the primary process due to its high production rates, design flexibility, repeatability, ability to process many materials, and low labor costs.
2) Secondary processes like trimming and drilling.
3) Tertiary painting process.
4) Material and manufacturing process compatibility.
5) A total cost per part of 96.55 Baht including material, tooling, and processing costs for the injection molded plastic parts.
Presentation slide of act 333 final
This document summarizes the costing and budgeting for sandal production. It includes analysis of direct material costs, direct labor costs, manufacturing overhead costs, and allocation of overhead. Budgets are presented for production, direct materials, direct labor, cost of goods sold, income statement, contribution margin, break-even point, margin of safety, and sensitivity analysis. The objective is to apply managerial accounting concepts to determine the full cost of each sandal and budget costs and profits.
rate analysis
The analysis of rates is determining the cost per unit of an item of work based on materials, labor, and other expenses. It involves calculating the costs of materials and labor, which vary by location, and determining the actual cost per unit. This is used to calculate the costs of extra work, revise rates due to cost changes, and ensure economical use of materials and processes. Factors that influence the analysis include material and labor costs, equipment, work conditions, specifications, and contractor profit.
Week 5
The primary manufacturing process for the shoes is casting because the switch is made of plastic and the globe is made of resin, which are suited for casting. The secondary process is drilling to fix the electrical circuit to the sole. The tertiary process is joining and painting - joining to connect the wire and assemble to the sole, and painting to make the shoes trendy. The material and manufacturing processes are compatible with the product geometry. The electrical circuit size suits the sole base and shoes can be different sizes. The material can withstand the normal load of a person's foot weight and be kept away from direct sunlight or water.
Fundamentals of Estimating and Costing
The document discusses the process of estimating for construction projects. It explains that estimates are needed to determine the approximate quantities of materials and labor costs required. There are different types of estimates including approximate estimates which provide an initial cost, and detailed estimates which provide a cost closer to the actual amount. Various methods are described for calculating estimates along with the units of measurement used. Record keeping forms like measurement sheets and abstract sheets are used to document the estimated costs.
Bamboo special
The document discusses various manufacturing processes and considerations for selecting processes for a product. It addresses choosing a primary, secondary and tertiary process based on the product's function, material compatibility, load requirements and ambient conditions. It also provides a calculation for determining the total manufacturing cost per part by summing the costs of material, tooling and processing. The cost factors include material price, waste percentage, number of parts per run, machine rate, labor costs and cycle time.
Bamboo special
The document discusses various manufacturing processes and considerations for selecting processes for a product. It addresses choosing a primary, secondary and tertiary process based on the product's function, material compatibility, load requirements and ambient conditions. It also provides a calculation for determining the total manufacturing cost per part by summing the costs of material, tooling and processing. The cost factors include material price, waste percentage, number of parts per run, machine rate, labor costs and cycle time.
Cost accounting project
The document summarizes the costs of three products (X, Y, Z) for a company using different costing methods. Under direct labor hour allocation of overheads, product X costs Rs. 61, product Y costs Rs. 74, and product Z costs Rs. 38. Using machine hours and material handling for overhead allocation, the costs are Rs. 66.54, Rs. 57.62, and Rs. 58.05 respectively. Activity based costing allocates overheads based on cost drivers and calculates the costs as Rs. 53.31, Rs. 50.07, and Rs. 126.65 respectively. The differences in product costs are due to the different allocation methods used for overhead costs.
Break even-point
This document discusses break-even analysis for three companies. Break-even analysis is used to predict when a business will start making a profit by determining the sales volume needed to cover total costs. It provides the break-even point in units and sales for each company. Company 1 produces bricks and has a break-even point of 10,000 units or Rs. 80,000 in sales. Company 2 produces concrete and has a break-even point of 400 tons or Rs. 333,200 in sales. Company 3 manufactures windows and doors and has a break-even point of 900 units or Rs. 162,000 in sales.
Estimation of wall
The document provides an example to calculate the quantities and costs of brickwork and plastering for a wall that is 4m long, 3m high and 30cm thick. It determines that the quantity of brickwork is 3.6 cubic meters at a rate of Rs. 320/cum, costing Rs. 1152. The quantity of plastering is 24 square meters at a rate of Rs. 8.50/sqm, costing Rs. 204. The total cost of the brickwork and plastering is Rs. 1356.
Costsheet final
This document provides a cost sheet analysis for a ladies clothing manufacturer. It includes details of direct costs like materials consumed and wages. It also lists factory overheads like handwork and coloring. Office overheads such as electricity are included. Sales and distribution overheads such as salesman salaries and commissions are specified. Calculations for prime cost, factory cost, cost of production and total cost are demonstrated. The cost sheet shows total sales of Rs. 911,000 with a net profit of Rs. 61,000, which is 6.70% of sales. In summary, the document presents a cost analysis for a clothing company through a detailed cost sheet.
Rate analysis vansheika
This document provides a rate analysis for 10 cubic meters of reinforced cement concrete (RCC) slab with a mix ratio of 1:2:4.
The rate analysis calculates costs for materials, labor, equipment rental, water charges, and contractor profit. Material costs include cement, sand, coarse aggregate, and steel reinforcement. Labor costs account for masons for mixing, transporting, placing, binding, and shuttering.
The total cost is Rs. 84,996, to which water charges of 1.5% and 10% contractor profit are added. The final rate calculated per cubic meter of RCC slab is Rs. 9,477.
Takiantong group
The main manufacturing processes are cutting, drilling, and painting. Cutting is used to separate the plastic bottle into 3 parts that are assembled. Drilling makes holes to attract flies to the light. Painting in black further draws flies into the holes and lamp.
Cost sheet ppt
The document discusses the components and computation of a cost sheet. It explains that a cost sheet tracks direct material costs, direct labor costs, direct expenses, factory/works overhead costs, office and administration overhead costs, and selling and distribution overhead costs. It provides a template for a cost sheet showing accounts for materials consumed, direct labor, prime costs, factory costs, production costs, cost of goods sold, and sales. It then provides an example cost sheet with specific costs to populate the template for a company.
What's hot (15)
Viewers also liked
Jet engine 2nd prototype
The project's second prototype requires extending the mold creation duration to improve quality and being more careful when ejecting work pieces from the mold. Leaks around the mold should also be identified before pouring resin. Key factors to consider include quality, weight, ease of use, manufacturing time, and cost.
Process selection
This document describes the 5-step process for manufacturing jet engines, including wood sculpting, mold creation, resin forming, trimming and drilling, and painting. The current process has workers manually transferring parts between each step, which could be improved for efficiency.
Material selection - Jet Engine
This document discusses three factors related to material selection: Young's Modulus and cost, strength compared to maximum service temperature, and recycle fraction and cost. It considers the tradeoffs between mechanical properties, operating conditions, sustainability, and financial costs for choosing the right material.
Jet engine final proto
The document discusses a final project prototype and evaluates its function, weight, strength, appearance, ease of use, fragile resistance, light weight, refillability, and decorative purpose. A strength test was conducted to determine the approximate height the product can handle before breaking, and it was found to be safe when falling from a height of 70cm or below.
Jet engine prototype
The document describes the first prototype of a project. It lists the name, description, material, manufacturing process, quantity, unit cost, and total cost for an upper cap and body cover. The prototype creation took 3 hours, mold creation took 14 hours, work piece molding took 3 hours, and drilling and finishing the surface took 1 hour.
Jet engine final present
The document describes a bamboo spray bottle inspired by bamboo's geometry. It is made to be fragile resistant, lightweight, refillable, and decorative. The manufacturing process involves creating a wood prototype, mold, molding the work piece, and drilling and finishing. The bamboo spray bottle can withstand drops from 70cm or below and addresses initial problems of lacking material and having a complicated model and short mold creation time.
Jet engine 2nd prototype
The project's second prototype requires extending the mold creation duration to improve quality and being more careful when ejecting work pieces from the mold. Leaks around the mold should also be identified before pouring resin. Key factors to consider include quality, weight, ease of use, manufacturing time, and cost.
Delta Chi Brothers Flashcards
This document appears to be a set of flashcards for pledges of the Delta Chi fraternity. Each flashcard contains information about an individual pledge, including their name, hometown, major, fraternity affiliation, big brother/little brother connections, parents' names, and siblings. There are 34 pledges featured in total.
Viewers also liked (19)
Recently uploaded
Anny Serafina Love - Letter of Recommendation by Kellen Harkins, MS.
This letter, written by Kellen Harkins, Course Director at Full Sail University, commends Anny Love's exemplary performance in the Video Sharing Platforms class. It highlights her dedication, willingness to challenge herself, and exceptional skills in production, editing, and marketing across various video platforms like YouTube, TikTok, and Instagram.
How are Lilac French Bulldogs Beauty Charming the World and Capturing Hearts....
โAfter being the most listed dog breed in the United States for 31
years in a row, the Labrador Retriever has dropped to second place
in the American Kennel Club's annual survey of the country's most
popular canines. The French Bulldog is the new top dog in the
United States as of 2022. The stylish puppy has ascended the
rankings in rapid time despite having health concerns and limited
color choices.โ
Business storytelling: key ingredients to a story
Storytelling is an incredibly valuable tool to share data and information. To get the most impact from stories there are a number of key ingredients. These are based on science and human nature. Using these elements in a story you can deliver information impactfully, ensure action and drive change.
Taurus Zodiac Sign: Unveiling the Traits, Dates, and Horoscope Insights of th...
Dive into the steadfast world of the Taurus Zodiac Sign. Discover the grounded, stable, and logical nature of Taurus individuals, and explore their key personality traits, important dates, and horoscope insights. Learn how the determination and patience of the Taurus sign make them the rock-steady achievers and anchors of the zodiac.
Brian Fitzsimmons on the Business Strategy and Content Flywheel of Barstool S...
On episode 272 of the Digital and Social Media Sports Podcast, Neil chatted with Brian Fitzsimmons, Director of Licensing and Business Development for Barstool Sports.
What follows is a collection of snippets from the podcast. To hear the full interview and more, check out the podcast on all podcast platforms and at www.dsmsports.net
Event Report - SAP Sapphire 2024 Orlando - lots of innovation and old challenges
Holger Mueller of Constellation Research shares his key takeaways from SAP's Sapphire confernece, held in Orlando, June 3rd till 5th 2024, in the Orange Convention Center.
DearbornMusic-KatherineJasperFullSailUni
My powerpoint presentation for my Music Retail and Distribution class at Full Sail University
The latest Heat Pump Manual from Newentide
๐๐ง๐ฏ๐๐ข๐ฅ ๐ญ๐ก๐ ๐
๐ฎ๐ญ๐ฎ๐ซ๐ ๐จ๐ ๐๐ง๐๐ซ๐ ๐ฒ ๐๐๐๐ข๐๐ข๐๐ง๐๐ฒ ๐ฐ๐ข๐ญ๐ก ๐๐๐๐๐๐๐๐โ๐ฌ ๐๐๐ญ๐๐ฌ๐ญ ๐๐๐๐๐ซ๐ข๐ง๐ ๐ฌ
Explore the details in our newly released product manual, which showcases NEWNTIDE's advanced heat pump technologies. Delve into our energy-efficient and eco-friendly solutions tailored for diverse global markets.
The 10 Most Influential Leaders Guiding Corporate Evolution, 2024.pdf
In the recent edition, The 10 Most Influential Leaders Guiding Corporate Evolution, 2024, The Silicon Leaders magazine gladly features Dejan ล tancer, President of the Global Chamber of Business Leaders (GCBL), along with other leaders.
TIMES BPO: Business Plan For Startup Industry
Starting a business is like embarking on an unpredictable adventure. Itโs a journey filled with highs and lows, victories and defeats. But what if I told you that those setbacks and failures could be the very stepping stones that lead you to fortune? Letโs explore how resilience, adaptability, and strategic thinking can transform adversity into opportunity.
Digital Marketing with a Focus on Sustainability
Digital Marketing best practices including influencer marketing, content creators, and omnichannel marketing for Sustainable Brands at the Sustainable Cosmetics Summit 2024 in New York
How MJ Global Leads the Packaging Industry.pdf
MJ Global's success in staying ahead of the curve in the packaging industry is a testament to its dedication to innovation, sustainability, and customer-centricity. By embracing technological advancements, leading in eco-friendly solutions, collaborating with industry leaders, and adapting to evolving consumer preferences, MJ Global continues to set new standards in the packaging sector.
2022 Vintage Roman Numerals Men Rings
Discover timeless style with the 2022 Vintage Roman Numerals Men's Ring. Crafted from premium stainless steel, this 6mm wide ring embodies elegance and durability. Perfect as a gift, it seamlessly blends classic Roman numeral detailing with modern sophistication, making it an ideal accessory for any occasion.
https://rb.gy/usj1a2
2024-6-01-IMPACTSilver-Corp-Presentation.pdf
IMPACT Silver is a pure silver zinc producer with over $260 million in revenue since 2008 and a large 100% owned 210km Mexico land package - 2024 catalysts includes new 14% grade zinc Plomosas mine and 20,000m of fully funded exploration drilling.
Authentically Social by Corey Perlman - EO Puerto Rico
Authentically Social by Corey Perlman - EO Puerto RicoCorey Perlman, Social Media Speaker and Consultant
Social media for business ย
Maksym Vyshnivetskyi: PMO KPIs (UA) (#12)
Maksym Vyshnivetskyi: PMO KPIs (UA)
Lemberg PMO School 2024
Website โ https://lembs.com/pmoschool
Youtube โ https://www.youtube.com/startuplviv
FB โ https://www.facebook.com/pmdayconference
How to Implement a Strategy: Transform Your Strategy with BSC Designer's Comp...
The Strategy Implementation System offers a structured approach to translating stakeholder needs into actionable strategies using high-level and low-level scorecards. It involves stakeholder analysis, strategy decomposition, adoption of strategic frameworks like Balanced Scorecard or OKR, and alignment of goals, initiatives, and KPIs.
Key Components:
- Stakeholder Analysis
- Strategy Decomposition
- Adoption of Business Frameworks
- Goal Setting
- Initiatives and Action Plans
- KPIs and Performance Metrics
- Learning and Adaptation
- Alignment and Cascading of Scorecards
Benefits:
- Systematic strategy formulation and execution.
- Framework flexibility and automation.
- Enhanced alignment and strategic focus across the organization.
Industrial Tech SW: Category Renewal and Creation
Every industrial revolution has created a new set of categories and a new set of players.
Multiple new technologies have emerged, but Samsara and C3.ai are only two companies which have gone public so far.
Manufacturing startups constitute the largest pipeline share of unicorns and IPO candidates in the SF Bay Area, and software startups dominate in Germany.
Recently uploaded (20)
Anny Serafina Love - Letter of Recommendation by Kellen Harkins, MS.
Anny Serafina Love - Letter of Recommendation by Kellen Harkins, MS.
ย
How are Lilac French Bulldogs Beauty Charming the World and Capturing Hearts....
How are Lilac French Bulldogs Beauty Charming the World and Capturing Hearts....
ย
Taurus Zodiac Sign: Unveiling the Traits, Dates, and Horoscope Insights of th...
Taurus Zodiac Sign: Unveiling the Traits, Dates, and Horoscope Insights of th...
ย
Brian Fitzsimmons on the Business Strategy and Content Flywheel of Barstool S...
Brian Fitzsimmons on the Business Strategy and Content Flywheel of Barstool S...
ย
Event Report - SAP Sapphire 2024 Orlando - lots of innovation and old challenges
Event Report - SAP Sapphire 2024 Orlando - lots of innovation and old challenges
ย
The 10 Most Influential Leaders Guiding Corporate Evolution, 2024.pdf
The 10 Most Influential Leaders Guiding Corporate Evolution, 2024.pdf
ย
Authentically Social by Corey Perlman - EO Puerto Rico
Authentically Social by Corey Perlman - EO Puerto Rico
ย
How to Implement a Strategy: Transform Your Strategy with BSC Designer's Comp...
How to Implement a Strategy: Transform Your Strategy with BSC Designer's Comp...
ย
Process selection
- 2. Primary Process -Mold & Prototype pattern Crafting
- 3. Secondary Process - Inject the the compound Resin in to the Mold and wait until ready
- 4. Tertiary Process - Finish the surface of the product and do the painting job
- 5. -Material Compatibility -Normal applied load -Normal ambient conditions -Process Compatibility
- 6. Mold : Plaster of Paris + Resin = 85 Baht Raw material : Silicone 0.166 kg = 58.1 Baht Wood Pattern = 15 Baht Labor & tools cost = 40 Baht Total cost per piece = 198.1 Baht [First time] = 113.1 Baht [Next