Dispersion Hardening:
Hard particles:
Mixed with matrix powder
Consolidated
Processed by powder metallurgy techniques
Second phase – Very little solubility (Even at elevated temp.)
No coherency
So thermally Stable at very high temp.
Resists :
Grain growth
Over aging
Recrystallization
Mobility of dislocation
Different from particle Metallic Composites (Volume Fraction is 3 to 4% max.) (Does not affect stiffness)
Examples : Al2O3 in Al or Cu, ThO2 in Ni
Dispersion Hardening:
Hard particles:
Mixed with matrix powder
Consolidated
Processed by powder metallurgy techniques
Second phase – Very little solubility (Even at elevated temp.)
No coherency
So thermally Stable at very high temp.
Resists :
Grain growth
Over aging
Recrystallization
Mobility of dislocation
Different from particle Metallic Composites (Volume Fraction is 3 to 4% max.) (Does not affect stiffness)
Examples : Al2O3 in Al or Cu, ThO2 in Ni
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
This module contain information about various processes involved in heat treatment process.Figures are also there to evaluate and understand the information properly.
Diffusion Bonding of Semi-Solid (SSM 356) Cast Aluminum AlloyIJMER
A new technique to achieve the globular weld structure of SSM 356 aluminum alloy was
conducted. The effect of joining parameters on the microstructure and mechanical properties of diffusion
bonding butt joints of semi-solid SSM 356 aluminum alloy was investigated by conditions as follows:
compressive pressure at 0.4, 0.9, 1.8, 2.4 and 2.7 MPa, with holding time 3 hours and temperature at
495oC under argon atmosphere at 4 liters per minute. The results showed that the compressive pressure
1.8 MPa, with holding time 3 hours and temperature 495oC, under argon atmosphere provided the highest
joint strength to 124.48 MPa. In addition, the results of the investigation have shown that the joint
efficiency was 72 percent compared with base metal and microstructure in weld zone (WZ) after welding
becomes globular structure. This microstructure, similar to the original structure of the base material, is a
globular structure but the grain size can grow at a higher temperature
Experimental Investigation on Characteristic Study of the Carbon Steel C45 in...IJMER
In this paper, the mechanical characteristics of C45 medium carbon steel are investigated
under various working conditions. The main characteristic to be studied on this paper is impact toughness
of the material with different configurations and the experiment were carried out on charpy impact testing
equipment. This study reveals the ability of the material to absorb energy up to failure for various
specimen configurations under different heat treated conditions and the corresponding results were
compared with the analysis outcome
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
This module contain information about various processes involved in heat treatment process.Figures are also there to evaluate and understand the information properly.
Diffusion Bonding of Semi-Solid (SSM 356) Cast Aluminum AlloyIJMER
A new technique to achieve the globular weld structure of SSM 356 aluminum alloy was
conducted. The effect of joining parameters on the microstructure and mechanical properties of diffusion
bonding butt joints of semi-solid SSM 356 aluminum alloy was investigated by conditions as follows:
compressive pressure at 0.4, 0.9, 1.8, 2.4 and 2.7 MPa, with holding time 3 hours and temperature at
495oC under argon atmosphere at 4 liters per minute. The results showed that the compressive pressure
1.8 MPa, with holding time 3 hours and temperature 495oC, under argon atmosphere provided the highest
joint strength to 124.48 MPa. In addition, the results of the investigation have shown that the joint
efficiency was 72 percent compared with base metal and microstructure in weld zone (WZ) after welding
becomes globular structure. This microstructure, similar to the original structure of the base material, is a
globular structure but the grain size can grow at a higher temperature
Experimental Investigation on Characteristic Study of the Carbon Steel C45 in...IJMER
In this paper, the mechanical characteristics of C45 medium carbon steel are investigated
under various working conditions. The main characteristic to be studied on this paper is impact toughness
of the material with different configurations and the experiment were carried out on charpy impact testing
equipment. This study reveals the ability of the material to absorb energy up to failure for various
specimen configurations under different heat treated conditions and the corresponding results were
compared with the analysis outcome
heat treatment is the controlled heating and cooling of metals for the purpose of altering their properties.
it is used in manufacturing providing simple and low cost means of obtaining desired properties
Quenching is a vital part of the heat treating process in manufacturing. This presentation by Houghton International will show you how to master the process for the most efficient quenching and heat treating operations.
this ppt is useful for understanding the concept of heat treatment process in steel.
it gives the idea about the various stages of heat treatment process in details
EXPERIMENT 8 PRECIPITATION HARDENING IN 2024 ALUMINUM .docxSANSKAR20
EXPERIMENT 8
PRECIPITATION HARDENING IN 2024 ALUMINUM
Objective
To study the time and temperature variations in the hardness of Al-4% Cu alloy on
isothermal aging.
Introduction
Materials can be hardened by inhibiting the motion of crystal defects called dislocations. In
pure metals, the presence of defects (such as vacancies, interstitials, dislocations and grain
boundaries) can enhance the strength. In single phase alloys, additional resistance to
deformation may arise from the presence of foreign atoms. In two-phase alloys, additional
stress is needed to enable the dislocation to intersect the second-phase particles. A finely
dispersed precipitate may, therefore, strengthen the material. This phenomenon is termed
precipitation hardening.
The thermodynamics of precipitation in 2024 Al can best be understood by referring to the
binary phase diagram of Aluminum-Copper in the aluminum-rich region in Figure 8-1.
When the aluminum-copper alloy of less than 5 wt% copper is heated to a temperature just
above the solvus line, only one phase (kappa, ) is thermodynamically stable. Other solid
phases dissolve (disappear). This process is called solution treatment. The only requirement
is that the specimen must be kept at this temperature for a long enough time. To solution
treat a sample of 2024 Al (4 wt% Cu), the sample should be heated to 930°F (500°C) and held
for 30 minutes.
When a solution treated sample is rapidly cooled (quenched) to below the solvus line (Figure
8-1), two phases are thermodynamically stable (kappa and theta). These phases are two
different solids, physically distinct, and separated by a phase boundary. The process is
similar to precipitation of salt in supersaturated brine.
The process of precipitation is not instantaneous, as is often the case in liquid-solid
precipitation. The process involves the formation of embryos of theta through thermal
fluctuations and their subsequent growth, once they achieve stability. With time, more and
more precipitates form. This process is called aging. Once the solution achieves an
equilibrium composition given by the solvus line for the aging temperature, precipitation
stops. For example, the precipitation of the copper-rich theta phase depletes the kappa phase
of copper to approximately 1-1/2 wt% Cu at 715°F (380°C).
The distribution of precipitates affects the hardness and yield strength. The hardness and
yield strength are greater when the precipitates are small and finely dispersed in the kappa
matrix than when the precipitates are large and not finely scattered. Therefore, to gain
hardness in 2024 Al, the specimen should be heat treated to produce a fine dispersion of
small precipitates.
Unfortunately, there is a tendency when thermodynamic equilibrium is reached for large
precipitates to grow and small precipitates to shrink. This will lower the surface to volume
ratio of the precip ...
Effect of PVD Coating and Carburizing on Wear Characteristics of Low Carbon S...IJERD Editor
Wear is a relative cyclic motion with small amplitude which occurs between two oscillating
surfaces, depending upon the loading conditions, material properties and environment. Surface Engineering
such as surface treatment, coating and surface modifications are employed to minimise the friction and improve
wear resistance of steel. In this work the low carbon steel substrate is coated with Al2O3 by using physical
vapour deposition process and the other sampling material is heat treated by carburizing process. In the present
study, the wear resistance of heat treated and coated steels were evaluated through the pin-on-disk using
variable loads and wear is measured by the wear track width and wear graphs are shown for coated material and
heat treated material. Finally, the comparison is concluded by observing the variations in wear characteristics
between the two samples. Furthermore morphological study of wear is made for in-depth analysis
As a part of course on Environments and Energy Materials, this was presented to explain the various areas (materials, manufacturing, testing) of advancement in turbines used for applications such as power generation and jet engines.
EFFECT OF SCANDIUM ON THE SOFTENING BEHAVIOUR OF DIFFERENT DEGREE OF COLD ROL...msejjournal
The softening behavior of different cold rolled Al-6Mg alloys containing scandium 0.2 wt% and 0.6 wt% have been investigated by means of microscopy, hardness and electrical conductivity measurements. It is found that the scandium added alloys attend the higher hardness at every state of cold rolling at higher
annealed temperature due to the precipitation of scandium aluminides. Electrical resistivity of the scandium added alloys show higher than base alloy due to grain refining. It is seen from the microstructure that scandium refine the grain structure and inhibit recrystallization.
Effect of Scandium on the Softening Behaviour of Different Degree of Cold Rol...msejjournal
The softening behavior of different cold rolled Al-6Mg alloys containing scandium 0.2 wt% and 0.6 wt% have been investigated by means of microscopy, hardness and electrical conductivity measurements. It is found that the scandium added alloys attend the higher hardness at every state of cold rolling at higher annealed temperature due to the precipitation of scandium aluminides. Electrical resistivity of the scandium added alloys show higher than base alloy due to grain refining. It is seen from the microstructure that scandium refine the grain structure and inhibit recrystallization.
Model Attribute Check Company Auto PropertyCeline George
In Odoo, the multi-company feature allows you to manage multiple companies within a single Odoo database instance. Each company can have its own configurations while still sharing common resources such as products, customers, and suppliers.
How to Create Map Views in the Odoo 17 ERPCeline George
The map views are useful for providing a geographical representation of data. They allow users to visualize and analyze the data in a more intuitive manner.
Read| The latest issue of The Challenger is here! We are thrilled to announce that our school paper has qualified for the NATIONAL SCHOOLS PRESS CONFERENCE (NSPC) 2024. Thank you for your unwavering support and trust. Dive into the stories that made us stand out!
The Art Pastor's Guide to Sabbath | Steve ThomasonSteve Thomason
What is the purpose of the Sabbath Law in the Torah. It is interesting to compare how the context of the law shifts from Exodus to Deuteronomy. Who gets to rest, and why?
The Roman Empire A Historical Colossus.pdfkaushalkr1407
The Roman Empire, a vast and enduring power, stands as one of history's most remarkable civilizations, leaving an indelible imprint on the world. It emerged from the Roman Republic, transitioning into an imperial powerhouse under the leadership of Augustus Caesar in 27 BCE. This transformation marked the beginning of an era defined by unprecedented territorial expansion, architectural marvels, and profound cultural influence.
The empire's roots lie in the city of Rome, founded, according to legend, by Romulus in 753 BCE. Over centuries, Rome evolved from a small settlement to a formidable republic, characterized by a complex political system with elected officials and checks on power. However, internal strife, class conflicts, and military ambitions paved the way for the end of the Republic. Julius Caesar’s dictatorship and subsequent assassination in 44 BCE created a power vacuum, leading to a civil war. Octavian, later Augustus, emerged victorious, heralding the Roman Empire’s birth.
Under Augustus, the empire experienced the Pax Romana, a 200-year period of relative peace and stability. Augustus reformed the military, established efficient administrative systems, and initiated grand construction projects. The empire's borders expanded, encompassing territories from Britain to Egypt and from Spain to the Euphrates. Roman legions, renowned for their discipline and engineering prowess, secured and maintained these vast territories, building roads, fortifications, and cities that facilitated control and integration.
The Roman Empire’s society was hierarchical, with a rigid class system. At the top were the patricians, wealthy elites who held significant political power. Below them were the plebeians, free citizens with limited political influence, and the vast numbers of slaves who formed the backbone of the economy. The family unit was central, governed by the paterfamilias, the male head who held absolute authority.
Culturally, the Romans were eclectic, absorbing and adapting elements from the civilizations they encountered, particularly the Greeks. Roman art, literature, and philosophy reflected this synthesis, creating a rich cultural tapestry. Latin, the Roman language, became the lingua franca of the Western world, influencing numerous modern languages.
Roman architecture and engineering achievements were monumental. They perfected the arch, vault, and dome, constructing enduring structures like the Colosseum, Pantheon, and aqueducts. These engineering marvels not only showcased Roman ingenuity but also served practical purposes, from public entertainment to water supply.
Palestine last event orientationfvgnh .pptxRaedMohamed3
An EFL lesson about the current events in Palestine. It is intended to be for intermediate students who wish to increase their listening skills through a short lesson in power point.
The French Revolution, which began in 1789, was a period of radical social and political upheaval in France. It marked the decline of absolute monarchies, the rise of secular and democratic republics, and the eventual rise of Napoleon Bonaparte. This revolutionary period is crucial in understanding the transition from feudalism to modernity in Europe.
For more information, visit-www.vavaclasses.com
How to Make a Field invisible in Odoo 17Celine George
It is possible to hide or invisible some fields in odoo. Commonly using “invisible” attribute in the field definition to invisible the fields. This slide will show how to make a field invisible in odoo 17.
How to Split Bills in the Odoo 17 POS ModuleCeline George
Bills have a main role in point of sale procedure. It will help to track sales, handling payments and giving receipts to customers. Bill splitting also has an important role in POS. For example, If some friends come together for dinner and if they want to divide the bill then it is possible by POS bill splitting. This slide will show how to split bills in odoo 17 POS.