This document provides an introduction to kinematics of machines. It defines key terms like link, kinematic chain, mechanism, degrees of freedom, and mobility. It describes different types of links, kinematic pairs, and classifications of links and kinematic pairs. Important concepts like inversion and Grubler's criterion for calculating the degrees of freedom of a mechanism are explained. Examples are provided to illustrate how to apply Grubler's criterion to determine the mobility of different mechanisms.
1. Mechanisms are constrained kinematic chains that convert one form of motion into another. They consist of links connected by various kinematic pairs which allow different degrees of freedom.
2. The number of degrees of freedom of a mechanism can be calculated using Grubler's equation. Common mechanisms include four-bar linkages, slider-crank mechanisms, and their inversions which are obtained by fixing different links.
3. Kinematic pairs like lower pairs, higher pairs, turning pairs, and sliding pairs connect the links of a mechanism and determine the relative motion between links. Planar mechanisms have all links moving in parallel planes.
Kinematic link, Types of links, Kinematic pair, Types of constrained motions, Types of Kinematic pairs, Kinematic chain, Types of joints, Mechanism, Machine, Degree of freedom, Mobility of Mechanism, Inversion, Grashoff’s law, Four-Bar Chain and its Inversions, Slider crank Chain and its Inversions, Double slider crank Chain and its Conversions, Mechanisms with Higher pairs, Equivalent Linkages and its Cases - Sliding Pairs in Place of Turning Pairs, Spring in Place of Turning Pairs, Cam Pair in Place of Turning Pairs
This document provides an introduction to machine fundamentals and mechanical engineering concepts. It defines a machine as a device that transmits and modifies energy to perform a specific task through interconnected components. Machines are designed to achieve a specific motion or force transformation and have defined inputs and outputs. The document then discusses different types of machines and provides examples. It defines links and kinematic pairs that connect machine components and allows relative motion. Different types of links, pairs, and kinematic chains are described. The document concludes with discussing different types of motions involved in mechanisms.
This document provides study materials for the course ME3491 Theory of Machines including an overview of the topics covered in Unit I on kinematics of mechanisms. It defines key terms like mechanisms, kinematic links, kinematic pairs, and kinematic chains. It also discusses various types of kinematic pairs and chains as well as analytical methods and computer approaches for kinematic analysis. The document concludes with sample two-mark questions and answers on topics related to kinematic analysis of mechanisms.
This document provides an overview of machine learning concepts for diploma and polytechnic students. It covers topics such as simple mechanisms, kinematic pairs, kinematic chains, and inversions. Specifically, it discusses four bar link mechanisms, the single slider crank chain, and their various inversions including beam engines, the coupling rod of locomotives, and Watt's indicator mechanism. It also provides examples of kinematic pairs like lower and higher pairs and defines terms like links, mechanisms, and machines. Diagrams are included to illustrate key concepts.
This document provides an overview of the topics covered in Module 1 of a course on the Finite Element Method. The module introduces mechanisms and their analysis. It discusses planar kinematic pairs, chains and their inversions. Methods for analyzing the velocity and acceleration of planar mechanisms both graphically and analytically are presented. Specific mechanisms covered include four-bar linkages, slider-crank mechanisms, and their inversions. The module also defines basic terms related to mechanisms, kinematics, and motion analysis.
1. Mechanisms are constrained kinematic chains that convert one form of motion into another. They consist of links connected by various kinematic pairs which allow different degrees of freedom.
2. The number of degrees of freedom of a mechanism can be calculated using Grubler's equation. Common mechanisms include four-bar linkages, slider-crank mechanisms, and their inversions which are obtained by fixing different links.
3. Kinematic pairs like lower pairs, higher pairs, turning pairs, and sliding pairs connect the links of a mechanism and determine the relative motion between links. Planar mechanisms have all links moving in parallel planes.
Kinematic link, Types of links, Kinematic pair, Types of constrained motions, Types of Kinematic pairs, Kinematic chain, Types of joints, Mechanism, Machine, Degree of freedom, Mobility of Mechanism, Inversion, Grashoff’s law, Four-Bar Chain and its Inversions, Slider crank Chain and its Inversions, Double slider crank Chain and its Conversions, Mechanisms with Higher pairs, Equivalent Linkages and its Cases - Sliding Pairs in Place of Turning Pairs, Spring in Place of Turning Pairs, Cam Pair in Place of Turning Pairs
This document provides an introduction to machine fundamentals and mechanical engineering concepts. It defines a machine as a device that transmits and modifies energy to perform a specific task through interconnected components. Machines are designed to achieve a specific motion or force transformation and have defined inputs and outputs. The document then discusses different types of machines and provides examples. It defines links and kinematic pairs that connect machine components and allows relative motion. Different types of links, pairs, and kinematic chains are described. The document concludes with discussing different types of motions involved in mechanisms.
This document provides study materials for the course ME3491 Theory of Machines including an overview of the topics covered in Unit I on kinematics of mechanisms. It defines key terms like mechanisms, kinematic links, kinematic pairs, and kinematic chains. It also discusses various types of kinematic pairs and chains as well as analytical methods and computer approaches for kinematic analysis. The document concludes with sample two-mark questions and answers on topics related to kinematic analysis of mechanisms.
This document provides an overview of machine learning concepts for diploma and polytechnic students. It covers topics such as simple mechanisms, kinematic pairs, kinematic chains, and inversions. Specifically, it discusses four bar link mechanisms, the single slider crank chain, and their various inversions including beam engines, the coupling rod of locomotives, and Watt's indicator mechanism. It also provides examples of kinematic pairs like lower and higher pairs and defines terms like links, mechanisms, and machines. Diagrams are included to illustrate key concepts.
This document provides an overview of the topics covered in Module 1 of a course on the Finite Element Method. The module introduces mechanisms and their analysis. It discusses planar kinematic pairs, chains and their inversions. Methods for analyzing the velocity and acceleration of planar mechanisms both graphically and analytically are presented. Specific mechanisms covered include four-bar linkages, slider-crank mechanisms, and their inversions. The module also defines basic terms related to mechanisms, kinematics, and motion analysis.
1. The document discusses the fundamentals and types of mechanisms in machine theory. It covers kinematics, dynamics, types of links, kinematic pairs, and classifications of kinematic pairs.
2. A kinematic chain is formed when kinematic pairs are coupled together to transmit motion. The relationships between the number of links, pairs, and joints in a kinematic chain are explained.
3. Common kinematic chains including four-bar chains, single slider-crank chains, and double slider-crank chains are described. Inversions of mechanisms by fixing different links are used to obtain different mechanisms.
This document discusses kinematic elements and pairs that are components of machines. It defines a kinematic link as any part that moves relative to another, and types of links include rigid, flexible, and fluid. Kinematic pairs constrain the relative motion between two links, and types of pairs are classified by the motion (sliding, turning, rolling, etc.) and contact (lower or higher). A kinematic chain combines multiple pairs so each link belongs to two pairs. When one link is fixed, it forms a mechanism that can transmit or transform motion. Common mechanisms are discussed like four-bar linkages and inversions obtained by fixing different links.
Introduction:
Definitions : Link or Element, Pairing of Elements with degrees of freedom, Grubler’s criterion (without derivation), Kinematic chain, Mechanism, Mobility of Mechanism, Inversions, Machine.
Kinematic Chains and Inversions:
Kinematic chain with three lower pairs, Four bar chain, Single slider crank chain and Double slider crank chain and their inversions.
Mechanisms:
i) Quick return motion mechanisms – Drag link mechanism, Whitworth mechanism and Crank and slotted lever mechanism
Mechanisms:
i) Quick return motion mechanisms – Drag link mechanism, Whitworth mechanism and Crank and slotted lever mechanism
ii) Straight line motion mechanisms – Peacelier’s mechanism and Robert’s mechanism.
iii) Intermittent motion mechanisms – Geneva mechanism and Ratchet & Pawl mechanism.
iv)Toggle mechanism, Pantograph, Hooke’s joint and Ackerman Steering gear mechanism.
Kinematics: The study of motion (position, velocity, acceleration). A major goal of understanding kinematics is to develop the ability to design a system that will satisfy specified motion requirements. This will be the emphasis of this class.
• Kinetics: The effect of forces on moving bodies. Good kinematic design should produce good kinetics.
• Mechanism: A system design to transmit motion. (low forces)
• Machine: A system designed to transmit motion and energy. (forces involved
• Basic Mechanisms: Includes geared systems, cam-follower systems and linkages (rigid links connected by sliding or rotating joints). A mechanism has multiple moving parts (for example, a simple hinged door does not qualify as a mechanism).
Examples of mechanisms: Tin snips, vise grips, car suspension, backhoe, piston engine, folding chair, windshield wiper drive system, etc
Types of motion: Mechanisms may produce motions that are pure rotation, pure translation, or a combination of the two. We reduce the degrees of freedom of a mechanism by restraining the ability of the mechanism to move in translation (x-y directions for a 2D mechanism) or in rotation (about the z-axis for a 2-D mechanism).
• Link: A rigid body with two or more nodes (joints) that are used to connect to other rigid bodies. (WM examples: binary link, ternary link (3 joints), quaternary link (4 joints)
• Joint: A connection between two links that allows motion between the links. The motion allowed may be rotational (revolute joint), translational (sliding or prismatic joint), or a combination of the two (roll-slide joint).
• Kinematic chain: An assembly of links and joints used to coordinate an output motion with an input motion.
Module 1 introduction to kinematics of machinerytaruian
This document provides information about the Kinematics of Machines course offered by the Department of Mechanical Engineering at JSS Academy of Technical Education in Bangalore, India. It lists the course code, textbooks, reference books, course outcomes, and chapter topics that will be covered. The topics include basic definitions related to kinematic elements, pairs, chains, and mechanisms. It describes types of kinematic pairs and chains, including four-bar chains, single slider-crank chains, and double slider-crank chains. It also covers degrees of freedom, Grubler's criterion, and inversions of mechanisms.
This document provides information about the Kinematics of Machines course offered by the Department of Mechanical Engineering at JSS Academy of Technical Education in Bangalore, India. It lists the course code, textbooks, reference books, course outcomes, and chapter topics that will be covered. The topics include basic definitions related to kinematic elements, pairs, chains, and mechanisms. It also describes common kinematic chains like four-bar linkages, single slider-crank mechanisms, and double slider-crank mechanisms. Specific examples and applications of each type are provided.
This document provides notes on kinematic mechanisms from a mechanical engineering course. It includes definitions of key terms like kinematic pairs, degrees of freedom, and Grubler's criterion. It discusses different types of kinematic chains including four bar chains, single slider crank chains, and double slider crank chains. It also summarizes inversions of these chains used in common mechanisms like the beam engine, locomotive coupling rod, and reciprocating engine. Examples of mechanisms derived from different inversions are provided like the rotary engine from the single slider crank chain.
Material and mechanical 5082_Lecture_1.pdfDrBarkatUllaha
Theory of Machines and Mechanism may be defined as the branch of engineering that deals with the study of relative motion between machine parts and the forces acting on them. It is essential for engineers to understand when designing machines. There are four main branches: kinematics studies motion without forces, dynamics studies forces during motion, kinetics deals with inertia forces from mass and motion, and statics studies forces when parts are at rest. Joints connect links to transmit motion and force, and can be classified by motion type, contact type, connection type, and number of links joined. The number of degrees of freedom determines the inputs needed to predict output motion.
The document provides information about the syllabus and units covered in the course 111301 Mechanics of Machines. It discusses key concepts related to mechanisms including kinematic pairs, degrees of freedom, inversions, and applications of slider crank and four bar mechanisms. It also covers topics like friction in pivots, collars, and screw joints; belt and rope drives; gearing and cam design; balancing of reciprocating masses; and vibration analysis of single degree of freedom systems. The objectives of the course are to expose students to different machine mechanisms, the forces involved, and vibrations during operation.
This document provides information about the Kinematics of Machines course offered by the Department of Mechanical Engineering at JSS Academy of Technical Education in Bangalore, India. It lists the textbook and reference books for the course, as well as the course outcomes which include being able to describe machine concepts and mechanisms, identify mechanism motions, analyze planar mechanisms analytically and graphically, analyze motion transmission elements like gears and cams, and utilize kinematic aspects for machine design. The document also provides an overview of the topics to be covered in the course, including basic definitions, kinematic chains, inversions, and types of kinematic pairs and linkages.
Theory Of Machines in Mechanical EngineeringMohammedAsman
The theory of machines is a branch of mechanical engineering that deals with the study of mechanisms and their applications in various systems. It encompasses the analysis, design, and optimization of mechanisms such as gears, linkages, cams, and mechanisms to transmit motion and forces. This field explores principles of kinematics, dynamics, and control to understand the behavior and performance of machines, aiding in the development of efficient and functional mechanical systems for various industries.
The document discusses the analysis and synthesis of mechanisms and machines. It provides definitions and explanations of key concepts related to kinematics and dynamics of machines including links, kinematic pairs, degrees of freedom, mechanisms, and machines. The summary discusses the analysis of existing mechanisms to study their motions and forces, while synthesis involves designing the parts of a mechanism. Key types of links, kinematic pairs, and methods for determining degrees of freedom of mechanisms are also summarized.
This document discusses the theory of machinery and kinematic analysis. It defines theory of machinery as the branch of engineering science dealing with relative motion between machine parts and forces acting on them. The theory is subdivided into kinematics, dynamics, kinetics, and statics. Kinematic links, pairs, and chains are also defined and classified. Common kinematic pairs like sliding, turning, rolling, and screw pairs are described along with examples. Finally, single and double slider crank chains, a crank and slotted lever quick return mechanism, and friction are briefly covered.
This document provides an overview of kinematics of machinery and mechanisms. It discusses:
1) The basics of mechanisms, including their function to transfer motion and forces. Kinematics deals with relative motion between machine parts, while dynamics deals with forces acting on moving parts.
2) Common kinematic pairs like sliding, turning, rolling, and spherical pairs that constrain relative motion between links. Lower pairs have surface contact while higher pairs have line or point contact.
3) Methods for analyzing the motion of mechanisms like velocity and acceleration diagrams, instantaneous centers of velocity, and criteria for determining degrees of freedom.
4) Applications of kinematic analysis to specific mechanisms like slider-crank, four-bar link
This document discusses links and kinematic pairs in mechanical mechanisms. It defines a link as a single resistant body or combination of bodies with inflexible connections that moves relative to other parts. Links are classified by the number of ends they connect to other links. Kinematic pairs connect links and allow relative motion between them. Pairs are classified by their type of contact, relative motion, and constraint between links. Common pairs include turning, sliding, rolling, and screw pairs. The document provides examples of links and pairs in slider-crank mechanisms.
This document provides information about a laboratory manual for the Basic Mechanical Engineering subject at Vidya Pratishthan's College of Engineering in Baramati. It includes the list of experiments to be conducted, details on planar mechanisms like 4-bar, 6-bar and 8-bar linkages, and experiments on power transmitting elements and heat transfer. The manual was prepared by Professor Sachin Bhosle and is valid for the academic years 2011-2013.
This document provides an introduction to mechanisms of machinery. It discusses key concepts like kinematics, which is the study of motion without regard to forces, and kinetics, which is the study of forces on systems in motion. It also defines mechanisms and machines, and distinguishes between the two. Important mechanism terminology is introduced, such as links, joints, degrees of freedom, and kinematic diagrams. Examples of kinematic diagrams are provided for a shear press and vise grips to illustrate how to draw the diagrams and identify the relevant components. Formulas for calculating the degree of freedom using Gruebler's equation and Kutzbach's equation are also presented.
Software Engineering and Project Management - Introduction, Modeling Concepts...Prakhyath Rai
Introduction, Modeling Concepts and Class Modeling: What is Object orientation? What is OO development? OO Themes; Evidence for usefulness of OO development; OO modeling history. Modeling
as Design technique: Modeling, abstraction, The Three models. Class Modeling: Object and Class Concept, Link and associations concepts, Generalization and Inheritance, A sample class model, Navigation of class models, and UML diagrams
Building the Analysis Models: Requirement Analysis, Analysis Model Approaches, Data modeling Concepts, Object Oriented Analysis, Scenario-Based Modeling, Flow-Oriented Modeling, class Based Modeling, Creating a Behavioral Model.
1. The document discusses the fundamentals and types of mechanisms in machine theory. It covers kinematics, dynamics, types of links, kinematic pairs, and classifications of kinematic pairs.
2. A kinematic chain is formed when kinematic pairs are coupled together to transmit motion. The relationships between the number of links, pairs, and joints in a kinematic chain are explained.
3. Common kinematic chains including four-bar chains, single slider-crank chains, and double slider-crank chains are described. Inversions of mechanisms by fixing different links are used to obtain different mechanisms.
This document discusses kinematic elements and pairs that are components of machines. It defines a kinematic link as any part that moves relative to another, and types of links include rigid, flexible, and fluid. Kinematic pairs constrain the relative motion between two links, and types of pairs are classified by the motion (sliding, turning, rolling, etc.) and contact (lower or higher). A kinematic chain combines multiple pairs so each link belongs to two pairs. When one link is fixed, it forms a mechanism that can transmit or transform motion. Common mechanisms are discussed like four-bar linkages and inversions obtained by fixing different links.
Introduction:
Definitions : Link or Element, Pairing of Elements with degrees of freedom, Grubler’s criterion (without derivation), Kinematic chain, Mechanism, Mobility of Mechanism, Inversions, Machine.
Kinematic Chains and Inversions:
Kinematic chain with three lower pairs, Four bar chain, Single slider crank chain and Double slider crank chain and their inversions.
Mechanisms:
i) Quick return motion mechanisms – Drag link mechanism, Whitworth mechanism and Crank and slotted lever mechanism
Mechanisms:
i) Quick return motion mechanisms – Drag link mechanism, Whitworth mechanism and Crank and slotted lever mechanism
ii) Straight line motion mechanisms – Peacelier’s mechanism and Robert’s mechanism.
iii) Intermittent motion mechanisms – Geneva mechanism and Ratchet & Pawl mechanism.
iv)Toggle mechanism, Pantograph, Hooke’s joint and Ackerman Steering gear mechanism.
Kinematics: The study of motion (position, velocity, acceleration). A major goal of understanding kinematics is to develop the ability to design a system that will satisfy specified motion requirements. This will be the emphasis of this class.
• Kinetics: The effect of forces on moving bodies. Good kinematic design should produce good kinetics.
• Mechanism: A system design to transmit motion. (low forces)
• Machine: A system designed to transmit motion and energy. (forces involved
• Basic Mechanisms: Includes geared systems, cam-follower systems and linkages (rigid links connected by sliding or rotating joints). A mechanism has multiple moving parts (for example, a simple hinged door does not qualify as a mechanism).
Examples of mechanisms: Tin snips, vise grips, car suspension, backhoe, piston engine, folding chair, windshield wiper drive system, etc
Types of motion: Mechanisms may produce motions that are pure rotation, pure translation, or a combination of the two. We reduce the degrees of freedom of a mechanism by restraining the ability of the mechanism to move in translation (x-y directions for a 2D mechanism) or in rotation (about the z-axis for a 2-D mechanism).
• Link: A rigid body with two or more nodes (joints) that are used to connect to other rigid bodies. (WM examples: binary link, ternary link (3 joints), quaternary link (4 joints)
• Joint: A connection between two links that allows motion between the links. The motion allowed may be rotational (revolute joint), translational (sliding or prismatic joint), or a combination of the two (roll-slide joint).
• Kinematic chain: An assembly of links and joints used to coordinate an output motion with an input motion.
Module 1 introduction to kinematics of machinerytaruian
This document provides information about the Kinematics of Machines course offered by the Department of Mechanical Engineering at JSS Academy of Technical Education in Bangalore, India. It lists the course code, textbooks, reference books, course outcomes, and chapter topics that will be covered. The topics include basic definitions related to kinematic elements, pairs, chains, and mechanisms. It describes types of kinematic pairs and chains, including four-bar chains, single slider-crank chains, and double slider-crank chains. It also covers degrees of freedom, Grubler's criterion, and inversions of mechanisms.
This document provides information about the Kinematics of Machines course offered by the Department of Mechanical Engineering at JSS Academy of Technical Education in Bangalore, India. It lists the course code, textbooks, reference books, course outcomes, and chapter topics that will be covered. The topics include basic definitions related to kinematic elements, pairs, chains, and mechanisms. It also describes common kinematic chains like four-bar linkages, single slider-crank mechanisms, and double slider-crank mechanisms. Specific examples and applications of each type are provided.
This document provides notes on kinematic mechanisms from a mechanical engineering course. It includes definitions of key terms like kinematic pairs, degrees of freedom, and Grubler's criterion. It discusses different types of kinematic chains including four bar chains, single slider crank chains, and double slider crank chains. It also summarizes inversions of these chains used in common mechanisms like the beam engine, locomotive coupling rod, and reciprocating engine. Examples of mechanisms derived from different inversions are provided like the rotary engine from the single slider crank chain.
Material and mechanical 5082_Lecture_1.pdfDrBarkatUllaha
Theory of Machines and Mechanism may be defined as the branch of engineering that deals with the study of relative motion between machine parts and the forces acting on them. It is essential for engineers to understand when designing machines. There are four main branches: kinematics studies motion without forces, dynamics studies forces during motion, kinetics deals with inertia forces from mass and motion, and statics studies forces when parts are at rest. Joints connect links to transmit motion and force, and can be classified by motion type, contact type, connection type, and number of links joined. The number of degrees of freedom determines the inputs needed to predict output motion.
The document provides information about the syllabus and units covered in the course 111301 Mechanics of Machines. It discusses key concepts related to mechanisms including kinematic pairs, degrees of freedom, inversions, and applications of slider crank and four bar mechanisms. It also covers topics like friction in pivots, collars, and screw joints; belt and rope drives; gearing and cam design; balancing of reciprocating masses; and vibration analysis of single degree of freedom systems. The objectives of the course are to expose students to different machine mechanisms, the forces involved, and vibrations during operation.
This document provides information about the Kinematics of Machines course offered by the Department of Mechanical Engineering at JSS Academy of Technical Education in Bangalore, India. It lists the textbook and reference books for the course, as well as the course outcomes which include being able to describe machine concepts and mechanisms, identify mechanism motions, analyze planar mechanisms analytically and graphically, analyze motion transmission elements like gears and cams, and utilize kinematic aspects for machine design. The document also provides an overview of the topics to be covered in the course, including basic definitions, kinematic chains, inversions, and types of kinematic pairs and linkages.
Theory Of Machines in Mechanical EngineeringMohammedAsman
The theory of machines is a branch of mechanical engineering that deals with the study of mechanisms and their applications in various systems. It encompasses the analysis, design, and optimization of mechanisms such as gears, linkages, cams, and mechanisms to transmit motion and forces. This field explores principles of kinematics, dynamics, and control to understand the behavior and performance of machines, aiding in the development of efficient and functional mechanical systems for various industries.
The document discusses the analysis and synthesis of mechanisms and machines. It provides definitions and explanations of key concepts related to kinematics and dynamics of machines including links, kinematic pairs, degrees of freedom, mechanisms, and machines. The summary discusses the analysis of existing mechanisms to study their motions and forces, while synthesis involves designing the parts of a mechanism. Key types of links, kinematic pairs, and methods for determining degrees of freedom of mechanisms are also summarized.
This document discusses the theory of machinery and kinematic analysis. It defines theory of machinery as the branch of engineering science dealing with relative motion between machine parts and forces acting on them. The theory is subdivided into kinematics, dynamics, kinetics, and statics. Kinematic links, pairs, and chains are also defined and classified. Common kinematic pairs like sliding, turning, rolling, and screw pairs are described along with examples. Finally, single and double slider crank chains, a crank and slotted lever quick return mechanism, and friction are briefly covered.
This document provides an overview of kinematics of machinery and mechanisms. It discusses:
1) The basics of mechanisms, including their function to transfer motion and forces. Kinematics deals with relative motion between machine parts, while dynamics deals with forces acting on moving parts.
2) Common kinematic pairs like sliding, turning, rolling, and spherical pairs that constrain relative motion between links. Lower pairs have surface contact while higher pairs have line or point contact.
3) Methods for analyzing the motion of mechanisms like velocity and acceleration diagrams, instantaneous centers of velocity, and criteria for determining degrees of freedom.
4) Applications of kinematic analysis to specific mechanisms like slider-crank, four-bar link
This document discusses links and kinematic pairs in mechanical mechanisms. It defines a link as a single resistant body or combination of bodies with inflexible connections that moves relative to other parts. Links are classified by the number of ends they connect to other links. Kinematic pairs connect links and allow relative motion between them. Pairs are classified by their type of contact, relative motion, and constraint between links. Common pairs include turning, sliding, rolling, and screw pairs. The document provides examples of links and pairs in slider-crank mechanisms.
This document provides information about a laboratory manual for the Basic Mechanical Engineering subject at Vidya Pratishthan's College of Engineering in Baramati. It includes the list of experiments to be conducted, details on planar mechanisms like 4-bar, 6-bar and 8-bar linkages, and experiments on power transmitting elements and heat transfer. The manual was prepared by Professor Sachin Bhosle and is valid for the academic years 2011-2013.
This document provides an introduction to mechanisms of machinery. It discusses key concepts like kinematics, which is the study of motion without regard to forces, and kinetics, which is the study of forces on systems in motion. It also defines mechanisms and machines, and distinguishes between the two. Important mechanism terminology is introduced, such as links, joints, degrees of freedom, and kinematic diagrams. Examples of kinematic diagrams are provided for a shear press and vise grips to illustrate how to draw the diagrams and identify the relevant components. Formulas for calculating the degree of freedom using Gruebler's equation and Kutzbach's equation are also presented.
Software Engineering and Project Management - Introduction, Modeling Concepts...Prakhyath Rai
Introduction, Modeling Concepts and Class Modeling: What is Object orientation? What is OO development? OO Themes; Evidence for usefulness of OO development; OO modeling history. Modeling
as Design technique: Modeling, abstraction, The Three models. Class Modeling: Object and Class Concept, Link and associations concepts, Generalization and Inheritance, A sample class model, Navigation of class models, and UML diagrams
Building the Analysis Models: Requirement Analysis, Analysis Model Approaches, Data modeling Concepts, Object Oriented Analysis, Scenario-Based Modeling, Flow-Oriented Modeling, class Based Modeling, Creating a Behavioral Model.
Advanced control scheme of doubly fed induction generator for wind turbine us...IJECEIAES
This paper describes a speed control device for generating electrical energy on an electricity network based on the doubly fed induction generator (DFIG) used for wind power conversion systems. At first, a double-fed induction generator model was constructed. A control law is formulated to govern the flow of energy between the stator of a DFIG and the energy network using three types of controllers: proportional integral (PI), sliding mode controller (SMC) and second order sliding mode controller (SOSMC). Their different results in terms of power reference tracking, reaction to unexpected speed fluctuations, sensitivity to perturbations, and resilience against machine parameter alterations are compared. MATLAB/Simulink was used to conduct the simulations for the preceding study. Multiple simulations have shown very satisfying results, and the investigations demonstrate the efficacy and power-enhancing capabilities of the suggested control system.
Comparative analysis between traditional aquaponics and reconstructed aquapon...bijceesjournal
The aquaponic system of planting is a method that does not require soil usage. It is a method that only needs water, fish, lava rocks (a substitute for soil), and plants. Aquaponic systems are sustainable and environmentally friendly. Its use not only helps to plant in small spaces but also helps reduce artificial chemical use and minimizes excess water use, as aquaponics consumes 90% less water than soil-based gardening. The study applied a descriptive and experimental design to assess and compare conventional and reconstructed aquaponic methods for reproducing tomatoes. The researchers created an observation checklist to determine the significant factors of the study. The study aims to determine the significant difference between traditional aquaponics and reconstructed aquaponics systems propagating tomatoes in terms of height, weight, girth, and number of fruits. The reconstructed aquaponics system’s higher growth yield results in a much more nourished crop than the traditional aquaponics system. It is superior in its number of fruits, height, weight, and girth measurement. Moreover, the reconstructed aquaponics system is proven to eliminate all the hindrances present in the traditional aquaponics system, which are overcrowding of fish, algae growth, pest problems, contaminated water, and dead fish.
artificial intelligence and data science contents.pptxGauravCar
What is artificial intelligence? Artificial intelligence is the ability of a computer or computer-controlled robot to perform tasks that are commonly associated with the intellectual processes characteristic of humans, such as the ability to reason.
› ...
Artificial intelligence (AI) | Definitio
Applications of artificial Intelligence in Mechanical Engineering.pdfAtif Razi
Historically, mechanical engineering has relied heavily on human expertise and empirical methods to solve complex problems. With the introduction of computer-aided design (CAD) and finite element analysis (FEA), the field took its first steps towards digitization. These tools allowed engineers to simulate and analyze mechanical systems with greater accuracy and efficiency. However, the sheer volume of data generated by modern engineering systems and the increasing complexity of these systems have necessitated more advanced analytical tools, paving the way for AI.
AI offers the capability to process vast amounts of data, identify patterns, and make predictions with a level of speed and accuracy unattainable by traditional methods. This has profound implications for mechanical engineering, enabling more efficient design processes, predictive maintenance strategies, and optimized manufacturing operations. AI-driven tools can learn from historical data, adapt to new information, and continuously improve their performance, making them invaluable in tackling the multifaceted challenges of modern mechanical engineering.
Introduction- e - waste – definition - sources of e-waste– hazardous substances in e-waste - effects of e-waste on environment and human health- need for e-waste management– e-waste handling rules - waste minimization techniques for managing e-waste – recycling of e-waste - disposal treatment methods of e- waste – mechanism of extraction of precious metal from leaching solution-global Scenario of E-waste – E-waste in India- case studies.
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...IJECEIAES
Medical image analysis has witnessed significant advancements with deep learning techniques. In the domain of brain tumor segmentation, the ability to
precisely delineate tumor boundaries from magnetic resonance imaging (MRI)
scans holds profound implications for diagnosis. This study presents an ensemble convolutional neural network (CNN) with transfer learning, integrating
the state-of-the-art Deeplabv3+ architecture with the ResNet18 backbone. The
model is rigorously trained and evaluated, exhibiting remarkable performance
metrics, including an impressive global accuracy of 99.286%, a high-class accuracy of 82.191%, a mean intersection over union (IoU) of 79.900%, a weighted
IoU of 98.620%, and a Boundary F1 (BF) score of 83.303%. Notably, a detailed comparative analysis with existing methods showcases the superiority of
our proposed model. These findings underscore the model’s competence in precise brain tumor localization, underscoring its potential to revolutionize medical
image analysis and enhance healthcare outcomes. This research paves the way
for future exploration and optimization of advanced CNN models in medical
imaging, emphasizing addressing false positives and resource efficiency.
Manufacturing Process of molasses based distillery ppt.pptx
kom unit-1.pdf
1. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 2 of 32
INTRODUCTION
LINK OR ELEMENT
A link (or element or kinematic link) is a resistance body (or assembly of resistance
bodies) that constitute the part (parts) of the machine connecting other parts which have motion
relative to it. A link which is stationary and which supports the moving members is called
frame. Characteristics of link are:
1. It should have relative motion
2. It need not necessarily be rigid body, but it must be a resistance body (a body capable
of transmitting the required forces with negligible deformation).
Ex: Liquids which are resistance to compressive forces, Chains, belts & ropes, which are
resistance to tensile forces, Slider crank mechanism which converts the reciprocating motion
of the slider into a rotary motion of the crank & vice versa (Fig.1).
It consists of following four links
1. Frame
2. Crank
3. Connecting rod
4. Slider
The slider (i.e. link 4) reciprocates in guide, which is connected to the frame. Hence guide also
becomes link 1 (i.e. frame)
Theory of Machines
(Study of relative motion between the parts of a machine & the
forces acting on those parts)
Dynamics of Machines
(Study of forces & their effects on the parts)
Kinematics of Machines
(Study of relative motion between the parts of a
machine i.e. position, displacement, velocity &
acceleration)
Statics
(Study of forces acting on various parts when
those parts are assumed to be without mass or
Kinetics
(Study of inertia forces which arises from the
combined effect of the mass & motion of the
Naveen Kishor P, Asst. Prof, MED, Mecs.
2. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 3 of 32
Connecting rod
Frame
Slider
Crank
1 1
2
3
4
Fig.1 Slider Crank Mechanism
Classification of links:
1. Depending upon the ends on which revolute or turning pairs can be placed
i. Binary link: A link which is connected to two other links, it is called binary
link.
ii. Ternary link: A link which is connected to three other links, it is called ternary
link.
iii. Quaternary link: A link which is connected to four other links, it is called
quaternary link.
2. Depending upon the effect on the link
i. Rigid link: One which does not undergo any deformation while transmitting
motion. Ex: connecting rod, crank etc
ii. Flexible link: One which partly deforms in a manner not to affect the
transmission of motion. Ex: belts, ropes, chains etc
iii. Fluid link: One which is formed by having a fluid in a receptacle & motion is
transmitted through the fluid by pressure or compression only. Ex: hydraulic
presses, jacks, brakes etc
iv. Floating link: One which connected to the frame.
KINEMATIC PAIRS
When two elements or links are connected in such a way that their relative motion is
completely constrained or successfully constrained, form a kinematic pair.
The three main types of constrained motions are:
1. Completely constrained: Motion between a pair of links is limited to a definite
direction. Ex: motion of a shaft with collars at each end in a circular hole, motion of a
square bar in a square hole, piston & cylinder.
Naveen Kishore P, Asst. Prof, MED, Mecs.
3. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 4 of 32
2. Incompletely constrained: Motion between a pair of links is not confined to a definite
direction. Ex: shaft in a circular hole.
3. Successfully constrained: Motion in a definite direction is not brought about by itself,
but by some other means. Ex: shaft in foot step bearing.
Classification of Kinematic Pair:
1. Based on type of contact between the elements
i. Lower pair: Two elements of a pair have a surface contact when relative motion
takes place. Ex: sliding pairs, turning pairs & screw pairs
ii. Higher pair: Two elements of a pair have a point or line contact when relative
motion takes place. Ex: gear drives, cam & follower, belt drives etc
2. Based on relative motion between the elements
i. Turning (revolute) pair: Two elements of a pair are connected in such a way that
one can only turn or revolve about a fixed axis of another link. Ex: a shaft with
collars at both ends fitted in to a circular hole, lathe spindle in head stock etc.
ii. Sliding pair: Two elements of a pair are connected in such a way that one can only
slide relative to the other. Ex: piston & cylinder, tail stock on lathe bed etc.
iii. Rolling pair: Two elements of a pair are connected in such a way that one rolls
over another fixed link. Ex: roller bearing, ball bearing etc.
iv. Screw (helical) pair: Two elements of a pair are connected in such a way that one
element can turn about the other by screw threads. Ex: bolt with nut, lead screw of
a lathe with nut etc.
v. Spherical pair: Two elements of a pair are connected in such a way that one
element (with spherical shape) turns or swivels about the other fixed element.
Ex: ball & socket joint, pen stand etc.
3. Based on mechanical constraints between the elements
i. Self-Closed pair: Two elements of a pair are connected mechanically in such a way
that only required kind of relative motion occurs. Ex: lower pairs.
ii. Force closed (Open) pair: Two elements of a pair are not connected mechanically
but are kept in contact by the action of external forces. Ex: cam & follower (kept in
contact by the forces exerted by spring & gravity)
Naveen Kishore P, Asst. Prof, MED, Mecs.
4. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 5 of 32
KINEMATIC CHAIN
Kinematic Chain is defined as the “combination of kinematic pairs, joined in such a way
that each link forms a part of two pairs and the relative motion between the links (elements) is
completely or successfully constrained. They are coupled in such a way that the last link is
always joined to the first link to transmit definite motion. Ex: slider crank mechanism
Link 1 is connected to link 2 and to link 4. Therefore links 1 & 2 is a kinematic pair and
links 1 & 4 is a kinematic pair. Hence link 1 forms a part of two pairs
Similarly link 2 forms a part of two pairs (i.e. link 2 – link 3 and link 2 – link 1)
Similarly, 3 and 4 each forms a part of two pairs
Hence in this each link forms a part of two pairs and motion of each relative to other is
definite.
Hence the total combination of these links is a kinematic chain.
If each link is assumed to form two pairs with two adjacent links, then the relation between the
number of pairs (p) forming a kinematic chain and the number of links (l) may be expressed in
the form of an equation:
)
1
(
4
2
p
l
Another relation between the number of links (l) and the number of joints (j) which constitute
a kinematic chain is given by the expression:
)
2
(
2
2
3
l
j
Note:
1. These two equations are applicable only to kinematic chains, in which lower pairs are used.
These equations may also be applied to kinematic chains, in which higher pairs are used.
In that case, each higher pair may be taken as equivalent to two lower pairs with an
additional element or link.
2. If L.H.S > R.H.S. then the chain is locked
3. If L.H.S = R.H.S. then the chain is constrained
4. If L.H.S < R.H.S. then the chain is unconstrained
MECHANISM
Mechanism is a constrained kinematic chain, with one link fixed, which is used to
transmit or transform motion.
Types of mechanism:
1. Simple mechanism: has four links.
2. Compound mechanism: has more than four links.
3. Complex mechanism: formed by the inclusion of ternary or higher order floating link to a
simple mechanism.
4. Planar mechanism: formed when all links of the mechanism lie in the same plane.
5. Spatial mechanism: formed when all links of the mechanism lie in the different plane.
6. Equivalent mechanism: formed when one pairs is replaced by other type of pairs and the
new mechanism obtained must have the same number of degrees of freedom as the original
mechanism. Ex: A turning pair can be replaced by a sliding pair, A spring can be replaced
by two binary links, A cam pair can be replaced by one binary link with two turning pairs
at each end.
Naveen Kishore P, Asst. Prof, MED, Mecs.
5. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 6 of 32
INVERSION:
The exchange of fixedness of an element with its mating element in a kinematic chain is called
inversion. Thus, in the Fig. 2 any one of the links may be arbitrary selected as the fixed link,
and each arrangement is an inversion of the others.
Note: Relative motions between the various links is not changed in any manner through the
process of inversion, but their absolute motions (those measured with respect to the fixed link)
may be changed drastically.
l
s
p
q
l
s
p
q
l
s
p
q
l
s
p
q
Fig. 2: Inversions of four bar mechanism
MACHINE:
A machine is a mechanism or group of mechanisms used to perform useful work. Its chief
function is to adopt a source of power to some specific work requirements.
STRUCTURE:
Structure is an assemblage of several resistance bodies having no relative motion between
them. These are meant for taking up loads. There is only straining action due to forces acting
on them.
Difference between machine & mechanism:
Sl.
No.
Particulars Mechanism Machine
1 Definition It is a constrained kinematic chain, with one
link fixed, which is used to transmit or
transform motion
A machine is a mechanism or group of
mechanisms used to perform useful
work
2 Purpose To transmit or transform motion To transmit energy or to do useful
work
3 Dependency No mechanism is necessarily a machine A machine is a series or train of
mechanism
4 Relationship It is a working model of any machine It is a practical development of any
mechanism
5 Examples Clock, mini-drafter etc. Steam engine, shaper etc.
Difference between machine & structure:
Sl.
No.
Particulars Machine Structure
1 Definition A machine is a mechanism or group of
mechanisms used to perform useful
work
It is an assemblage of several resistance
bodies having no relative motion between
them
2 Work Modifies or transmit energy to do some
kind of work
Modifies & transmit force only
3 Relative
motion
Exists between its members Not exists between its members
4 Energy Transmits useful energy No energy transmission
5 Examples Steam engine, shaper etc. Roof truss, railway bridges, machine
frames etc.
Naveen Kishore P, Asst. Prof, MED, Mecs.
6. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 7 of 32
DEGREES OF FREEDOM:
It is defined as the number of independent relative motions, both translational & rotational,
a pair can have.
An unconstrained rigid body moving in apace can describe the following independent
motions.
o Translation motion along three mutually perpendicular axes x, y & z
o Rotation motion about these axes.
Thus, a rigid body possesses 6 degrees of freedom.
The connection of a link with another imposes certain constraints on their relative motion.
The number of restraints can never be zero (joint is disconnected) or six (joint becomes
solid).
Degrees of freedom = 6 – number of restraints
MOBILITY OF MECHANISM AND GRUBLER’S CRITERION
Mobility of Mechanism defines the number of degrees of freedom. The Grubler’s mobility
equation for a planar mechanism is
2
1
2
1
3 j
j
l
F
Where,
F = mobility of number of degrees of freedom
l = number of links including frame
j1 = joints with single (one) degree of freedom (lower pairs or binary joints)
j2 = joints with two degrees of freedom (higher pairs)
If, F > 0, results a mechanism with F degrees of freedom
F = 0, results in a statically determinate structure
F < 0, results in a statically indeterminate structure
Note: A joint connecting l links at a single point must be counted as (l-1) joints.
Example 1: (mechanisms with lower pairs)
Fig. (a) Fig. (b) Fig. (c) Fig. (d) Fig. (e)
Ans: 2
1
2
1
3 j
j
l
F
Naveen Kishore P, Asst. Prof, MED, Mecs.
7. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 8 of 32
Fig. Type l j1 j2 Calculation F
a Three bar
mechanism
3 3 0 F = 3 (3 - 1) -
2 × 3 – 0
0
b Four bar
mechanism
4 4 0 F = 3 (4 - 1) -
2 × 4 – 0
1
c Five bar
mechanism
5 5 0 F = 3 (5 - 1) -
2 × 5 – 0
2
d Five bar
mechanism
5 6
(because there are two binary joints at B
& D will be considered as two, and two
ternary joints at A & C will be considered
as {l-1} i.e. [3-1] × 2)
0 F = 3 (5 - 1) -
2 × 6 – 0
0
e Six bar
mechanism
6 8
(because there are four ternary joints at A,
B, C & D will be considered as {l-1} i.e.
[3-1] × 4)
0 F = 3 (6 - 1) -
2 × 8 – 0
-1
Conclusion:
1. When F = 0, then the mechanism forms a structure & no relative motion between the
links is possible as shown in the fig (a) & (d).
2. When F = 1, then the mechanism can be driven by a single input motion, as shown in
the fig (b).
3. When F = 2, then two separate input motions are necessary to produce constrained
motion for the mechanism, as shown in the fig (c).
4. When F = -1 or less then there are redundant constrains in the chain and it forms strictly
indeterminate structure, as shown in the fig (e).
Example 2: (mechanisms with higher pairs)
Fig (a) Fig (b)
Fig. Type l j1 j2 Calculation F
a Cam & follower
mechanism
3 2 1
(there exist a rolling & sliding
between 2 & 3)
F = 3 (3 - 1) - 2 ×
2 – 1
1
b Roller mechanism 4 3 1
(there exist a rolling & sliding
between 4 & 1)
F = 3 (4 - 1) - 2 ×
3 – 1
2
Note: In the second case (fig. b) it has been assumed that the slipping is possible between the
links (i.e. between the wheel & the fixed link). However, if the friction at the contact is high
enough to prevent slipping, the joint will be counted as one degree of freedom pair, because
only one relative motion will be possible between the links.
Naveen Kishore P, Asst. Prof, MED, Mecs.
8. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 9 of 32
Problems on Grubler’s Criterion:
(i)
F = 3(4-1)-2(4) = 1
i.e., one input to any one link will result in definite
motion of all the links.
(ii)
F = 3(5-1)-2(5) = 2
i.e., two inputs to any two links are required to yield
definite motions in all the links.
(iii)
F = 3(6-1)-2(7) = 1
i.e., one input to any one link will result in definite
motion of all the links.
(iv)
F = 3(6-1)-2(7) = 1
i.e., one input to any one link will result in definite
motion of all the links.
(v)
F = 3(11-1)-2(15) = 0
the mechanism forms a structure & no
relative motion between the links is possible
(vi)
Total number of links n = 7
Joints with one degree of freedom 10
1
j
Joints with two degree of freedom 0
2
j
2
0
10
2
1
7
3
F
Hence the linkage is a statically indeterminate structure.
Welded
Naveen Kishore P, Asst. Prof, MED, Mecs.
9. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 10 of 32
(vii)
(viii)
(ix)
(x)
F = 3(12-1)-2(16)-0 = 1
(xi)
F = 3(14-1)-2(18)-1 = 2
(xii)
F = 3(13-1)-2(18)-0 = 0
(xiii)
F = 3(4-1)-2(5) = -1
i.e., it is a structure
(xiv) (xv)
F = 3(3-1)-2(2)-1 = 1 F = 3(3-1)-2(2)-1 = 1
Naveen Kishore P, Asst. Prof, MED, Mecs.
10. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 11 of 32
GROSHOFF’S CRITERIA:
For a four-bar mechanism, the sum of the shortest & the longest link lengths should not be
greater than the sum of the remaining two link lengths if there is to be continuous relative
motion between the two links.
s + l < p + q
where: s = shortest link length, l = longest, p & q = intermediate length links
TYPES OF KINEMATIC CHAINS WITH FOUR LOWER PAIRS:
Kinematic chain with four lower pairs are important, each pair being a sliding pair or a turning pair. The
following types of kinematic chains and its inversions are important from practical point of view.
1. FOUR BAR OR QUADRIC CYCLE CHAIN
3(l)
2(s)
1(p)
4(q) s
A B
C
D
It consists of four binary links, each of them form a turning pair at A, B, C & D.
The four links of may be of different lengths.
According to the Grashof’s law for a four-bar mechanism, the sum of the shortest & the
longest link lengths should not be greater than the sum of the remaining two link lengths
if there is to be continuous relative motion between the two links.
Kinematic chain
Slider crank chain Double slider crank chain
Four bar or Quadric cycle chain
i) crank & lever
mechanism
ii) Double crank
mechanism
iii) Double lever
mechanism
i) Elliptical trammel
ii) Scotch yoke
mechanism
iii) Oldham’s
coupling
i) Reciprocating engine mechanism (1st
inversion)
ii) Oscillating cylinder engine mechanism (2nd
inversion)
iii) Crank & slotted lever mechanism (2nd
inversion)
iv) Whitworth quick return motion mechanism (3rd
inversion)
v) Rotary engine mechanism (3rd
inversion)
vi) Bull engine mechanism (4th
inversion)
vii) Hand pump (4th
inversion)
Note:
s = shortest
l = longest
p & q = other two links
Naveen Kishore P, Asst. Prof, MED, Mecs.
11. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 12 of 32
In this mechanism one of the links, in particular shortest link, will make a complete
revolution relative to the other three links, if it satisfies the Grashof’s law, known as
crank or driver (AD i.e. link 4).
The link BC (link 2) if it makes partial rotation or oscillation, known as lever or rocker
or follower, or another crank, if it rotates.
The link opposite to the fixed link, link CD (link 3) which connects the crank & lever
is called connecting rod or coupler.
The fixed link AB (link 1) is known as frame of the mechanism.
The four-bar chain with all its pairs as turning pairs is called the Quadric cycle chain.
When one of these turning pairs is replaced by a slider pairs, the chain becomes single
slider chain.
When two turning pairs are replaced by slider pairs, it is called double slider chain or a
crossed double slider chain, depending on whether the two slider pairs are adjacent or
crossed.
Inversions of Four bar chain: (based on Grashof’s law)
3
2
1
4
A B
C
D
4
5
m
m
30mm
2
0
m
m
50mm
3
2
1
4
A B
C
D
4
5
m
m
30mm
2
0
m
m
50mm
Fig (a) I inversion Fig (b) II inversion
3
2
1
4
A B
C
D
4
5
m
m
30mm
2
0
m
m
50mm
3
2
1
4
A B
C
D
4
5
m
m
30mm
2
0
m
m
50mm
Fig (c) III inversion Fig (d) IV inversion
Naveen Kishore P, Asst. Prof, MED, Mecs.
12. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 13 of 32
Let the longest link be l, the shortest link be s and the remaining two p & q.
Applying Grashof’s law, i.e. l +s < p + q four possibilities exists.
Fig (a) & (b) show two different crank-rocker mechanisms.
In each, the shortest link is the crank, the fixed link being either adjacent link.
Fig (c) shows one double crank (drag link) when the fixed link is the shortest link.
Fig (d) shows double rocker mechanism when link opposite to the shortest link is the
fixed link.
I & II inversions
Crank & rocker mechanism and Beam engine (rotary & oscillatory motion)
3
2
1
4
A
B
C
D
5
0
m
m
100mm
2
0
m
m
120mm
C1
C2
B1
B2
1
2
3
4
1
A
B
C
D
E
Fig. (a) Fig. (b)
The link 1 is fixed and the lengths 2, 3 & 4 are proportionate in such a way that crank AB
is able to rotate completely.
The follower CD only oscillates from C1 to C2 as shown in the fig (a).
The initial position of the mechanism is shown by full lines whereas the dotted line show
the mechanism for two extreme different positions.
Since one link rotates & other oscillates, it is known as crank & lever mechanism.
A part of the mechanism of beam engine , which consists of four links is shown in the fig
(b)
In fig (b), when the crank rotates about the fixed centre A, the lever oscillates about the
fixed centre D.
The end E of the fixed of the lever CDE is connected to a piston rod which reciprocates
due to the rotation of the crank.
In other words purpose of this mechanism is to convert rotary motion into reciprocating
motion.
III inversions
Coupling rod of locomotive or double crank mechanism (complete rotation of the crank
& follower)
In this mechanism length of link AD = length of link BC.
Length of link AB = length of link CD.
When AB rotates about A, the crank DC rotates about D.
This mechanism is used for coupling locomotive wheels.
Since links AB & CD works as cranks, this mechanism is also known as double crank
mechanism.
Naveen Kishore P, Asst. Prof, MED, Mecs.
13. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 14 of 32
IV inversions
Watt’s straight line mechanism or double lever mechanism (oscillatory motion)
It is very simple mechanism originally used by James Watt for guiding the motion of the
piston of his steam engine to have an approximate straight line motion.
It has four links OA, AB, BC & CO.
The link CO is fixed.
The link AO can oscillate about the centre O whereas the link BC can oscillate about the
centre C as shown in the fig.
In the mean position of the mechanism, the links AO and BC are parallel and link AB is
perpendicular to AO and BC.
It is seen that, if D is the point on link AB such that DA/DB = BC/OA, then for small
oscillations of OA and BC, the point D will trace an approximate straight line.
In fig, approximate straight line is shown when D is in three different positions.
2. SINGLE SLIDER CRANK CHAIN
Connecting rod
Frame
Slider
Crank
1 1
2
3
4
Naveen Kishore P, Asst. Prof, MED, Mecs.
14. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 15 of 32
It is a modification of basic four bar chain.
It consists of a one sliding pair & three turning pairs.
This type of mechanism converts rotary motion into reciprocating motion & vice versa.
Turning pairs are links 1 & 2, links 2 & 3 and links 3 & 4.
Sliding pair is links 4 & 1.
Inversions of Single slider crank chain:
i) First inversion:
Connecting rod
Frame
Slider
Crank 1
2
3
4
1
Connecting rod
Frame
Piston
Crank
1
2
3
4
Cylinder
Fig (a) Fig (b)
When link 1 is fixed, link 2 is made as crank and link 4 is made as slider, then first inversion
of single slider crank is obtained, shown in fig (a).
This inversion is used in reciprocating engine & reciprocating compressors as shown in the
fig (b), where link 1 corresponds to frame which is fixed; link 2 corresponds to crank, link
3 corresponds to connecting rod link 4 corresponds to piston.
In case of reciprocating engines, the link 4, piston becomes driver where as in case of
reciprocating compressors, link 2 (crank) is the driver.
Example: steam engine, compressors, pumps, I.C. engines etc.
ii) Second inversion:
1
2
3
4
A
B
C
The second inversion is obtained by fixing the link 3 (connecting rod).
Link 2 acts as a crank and is rotating about the point B.
Link 4 oscillates.
Naveen Kishore P, Asst. Prof, MED, Mecs.
15. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 16 of 32
Example 1: Oscillating cylinder engine mechanism
1
2
3
4
A
B
C
It is used to convert reciprocating motion into rotary motion.
In this mechanism, the link 3 forming the turning pair is fixed which corresponds to
connecting rod of a reciprocating steam engine mechanism.
When the crank (link 2) rotates, the piston attached to the piston rod (link 1) reciprocates
and the cylinder (link 4) oscillates about a pin pivoted to the fixed link at C.
Example 2: Crank & slotted lever mechanism
Fig (a) shows crank & slotted lever mechanism, in which link CB (link 3), corresponds to
the connecting rod, is fixed.
Driving crank AB (link 2) revolves about the centre B in clockwise direction.
A slider (link 4) is attached to the crank pin at A slides along the slotted lever CD (link 1)
and make the slotted lever oscillates about the pivoted point C.
Link DE (link 5) is attached to the slotted lever (link 1), which in turn is connected to the
cutting tool i.e. link 6.
Link 6 is contained to slide as shown in the fig.
Fig (b) shows the two extreme positions of the crank.
First position is when the crank (i.e. link 2) is at right angles to link 1 (or link 1 is tangential
to crank radius circle at point A1).
The remaining corresponding points in this will be D1 & E1.
Stroke of the cutting tool starts from point E1.
The crank is rotating in clockwise direction.
The end of the cutting stroke is marked by E2, when again crank after having rotated
through an angle in clock wise direction is again at right angle to the link 1 at position
A2.
Naveen Kishore P, Asst. Prof, MED, Mecs.
16. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 17 of 32
4 (slider)
2
3
1
A
B
C
5
6
D
E
3
B
C
D1
E1
9
0
°
9
0
°
E2
D2
Stroke
A1 A2
b
Fig (a) Fig (b)
Hence the cutting stroke occurs when crank rotates through an angle and return stroke
occurs when crank rotates through an angle b or (3600 - ) in clockwise direction.
Since the crank has a uniform angular speed, therefore
Time of cutting stroke / time of return stroke = / b = / (3600 - )
Since the angle is more than angle b as seen from the fig. (b), the cutting time will be
more than return time.
iii) Third inversion:
1
2 3
4
A
B
C
By fixing the link 2 (crank) third inversion is obtained.
Link 3 along with slider at its end C, becomes a crank.
Hence link 3 along with slider (link 4) rotates about B.
By doing so, the link 1 rotates about A along with the slider (link 4) which reciprocates on
link 1.
Example 1: Whiteworth Quick-Return Motion mechanism
Fig (a) shows Whiteworth Quick Return Motion Mechanism, in which link AB (link 2),
corresponds to the crank, is fixed.
Driving crank BC (link 3) revolves about the centre B in counter clockwise direction.
A slider (link 4) is attached to the crank pin at C slides along the slotted lever CD (link 1)
and make the slotted lever oscillates about the pivoted point A.
Naveen Kishore P, Asst. Prof, MED, Mecs.
17. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 18 of 32
Link DE (link 5) is attached to the slotted lever (link 1), which in turn is connected to the
cutting tool i.e. link 6.
Link 6 is contained to slide as shown in the fig.
1
2
3
4
A
B
C
D
E
5
6
A
B
D1 D2 C1
C2
E1 E2
STROKE
b
Fig (a) Fig (b)
Fig (b) shows the two extreme positions of the crank.
First position is when the slotted lever CD (link 1) is at right angles to link 2 (or link 5 is
collinear to link 1 at point C1).
The remaining corresponding points in this will be D1 & E1.
Stroke of the cutting tool starts from point E1.
The crank is rotating in counter clockwise direction.
The end of the cutting stroke is marked by E2, when again driving crank after having rotated
through an angle in counter clock wise direction is again at right angle to the link 2 at
position C2.
Hence the cutting stroke occurs when crank rotates through an angle and return stroke
occurs when crank rotates through an angle b or (3600 - ) in counter clockwise direction.
Since the crank has a uniform angular speed, therefore
Time of cutting stroke / time of return stroke = / b = / (3600 - )
Since the angle is more than angle b as seen from the fig. (b), the cutting time will be
more than return time.
Used in shaping and slotting machines.
Example 2: Rotary Engine or Gnome Engine
Fig (a) shows Rotary Engine or Gnome Engine Mechanism, in which link AB (link 2),
corresponds to the crank, is fixed.
Link 1 is made as the piston and link 4 is made as cylinder.
Here instead of one cylinder, seven or nine cylinders are symmetrically placed at regular
intervals in the same plane.
All the cylinders rotate about the same fixed centre A.
The fixed link is common to all the cylinders.
When the piston reciprocates in the cylinders, the whole assembly of cylinders, pistons &
connecting rods rotate about the axis A, where entire mechanical power is developed, is
obtained in the form of rotation of the crankshaft.
Naveen Kishore P, Asst. Prof, MED, Mecs.
18. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 19 of 32
The only difference between first inversion and this example of third inversion is that, the
crank rotates & body is fixed in the first inversion, whereas here the crank is fixed and the
body rotates.
It is a rotary cylinder V type internal combustion engine used as an aero-engine, which now
has been replaced by gas turbine.
iv) Fourth inversion:
1
2
3
4
A
B
C
By fixing the link 4 (sliding pair or cylinder) fourth inversion is obtained.
Link 3 can oscillate about the fixed-point C on link 4.
This makes end B of link 2 to oscillate about C and end A reciprocates along the axis of
the fixed link 4.
Example: Bull Engine Mechanism or Pendulum Pump and hand pump
A
B
C
D
A
B
C
D
Fig (a) Bull Engine Mechanism or Pendulum Pump Fig (b) Hand pump
Naveen Kishore P, Asst. Prof, MED, Mecs.
19. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 20 of 32
Bull Engine Mechanism or Pendulum Pump:
This inversion is obtained by fixing the die block D as shown in the fig (a).
As the link BC rotates, the link CD will oscillates about the pin D and the slotted link
AB will reciprocates along the vertical straight line.
Hand pump:
It is obtained by fixing the die block D as shown in the fig (b).
As the link BC oscillates about bin D, the slotted link AB reciprocates a vertical straight
line.
3. DOUBLE SLIDER CRANK CHAIN
1
2
3
4
1
It is a four-bar kinematic chain containing two turning pairs and two sliding pairs.
Link 1 & link 2 is sliding pair, link 2 & link 3 is turning pair, link 3 & link 4 is second
turning pair, link 4 & link 1 is second sliding pair.
Also, the two pairs of the same kind are adjacent (To adjacent pairs 23 & 34 are turning
pairs whereas the other two pairs 12 & 14 are sliding pairs)
Inversions of Single slider crank chain:
i) First inversion:
1
2
3
4
1
When link 1 is fixed, the first inversion is obtained as shown in the fig.
Two adjacent pairs 23 and 34 are turning pairs whereas the other two pairs 12 and 14 are
sliding pair.
Naveen Kishore P, Asst. Prof, MED, Mecs.
20. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 21 of 32
Example: Elliptical Trammel
1
2
3
4
1
A
B
C
X
Y
q
q
q
x
y
A
B
C
O
Fig (a) Fig (b)
The fixed link 1 has two straight grooves cut in it, at right angle to each other.
With the movement of the sliders any point C on the link 3 (except the midpoint of AB)
will trace an ellipse on a fixed plate.
The midpoint of AB will trace a circle.
Proof:
Let the coordinates of the point C at any instant are x and y as shown in the fig (b).
Let q is the angle made by link AC with horizontal at that instant.
Then,
BC
x
q
cos and
AC
y
q
sin
Squaring and adding, we get
q
q 2
2
2
2
2
2
sin
cos
AC
y
BC
x
1
2
2
2
2
AC
y
BC
x
This is the equation of ellipse. Hence the path traced by the point C is an ellipse whose semi
major axis is AC and semi minor axis is BC.
If C is the midpoint of AB, then AC = BC
1
2
2
2
2
AC
y
AC
x
2
2
2
AC
y
x
Naveen Kishore P, Asst. Prof, MED, Mecs.
21. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 22 of 32
This is the equation of circle whose radius is AC or BC.
Application: Used to draw an ellipse.
ii) Second inversion:
1
2
3
4
1
A
B
When link 2 or link 4 of the double slider crank chain is fixed, the second inversion is
obtained.
Here link 2 is fixed and end B of the link 3 rotates about the about A and link 4 will
reciprocate in the vertical slot.
Hence, link 1 reciprocates in the horizontal direction.
Example: Scotch Yoke Mechanism
This mechanism gives simple harmonic motion.
Here the slider A (link 2) is fixed.
As AB (link 3) rotates about A, the slider B (link 4) reciprocates in the vertical slot and
the link 1 reciprocates in the horizontal direction.
2
3
4
1
A
B
2
Application: Used to convert rotary motion to reciprocating motion. Its early application was
on steam pumps, but it is now used as a mechanism on a test machine to produce vibrations.
Naveen Kishore P, Asst. Prof, MED, Mecs.
22. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 23 of 32
iii) Third inversion:
1
2
3
4
1
A
B
When the link 3, of the double slider crank chain is fixed & link 1 is free to move, the third
inversion is obtained.
In this case, each of the slider blocks (i.e. link 2 & link 4) can turn about the pins A & B. if
one slide block (say link 2) is turned through an definite angle, the frame (i.e. link 1) and
other block (i.e. link 4) must turn through the same angle.
Example: Old Ham’s coupling
Application: Used for connecting two parallel shafts when the distance between the two shafts
is small.
The two shafts to be connected have flanges at their ends which are rigidly fastened by
forging to the shafts.
These flanges forms link 2 & link 4.
Each of these links forms a turning pair with link 3.
There is a diametrical slot cut in the inner faces of these flanges.
An intermediate piece is a circular disk (link 3) has two tongues T1 & T2 on each face at
right angles to each other.
These tongues can slide fit in the slots in the two flanges (link 2 & 4).
The link 3 can slide or reciprocate in the slots in the flanges.
Frame and bearing forms the link 1, which is fixed.
When the driving shaft is rotated, the flange A (link 2) connected rigidly to the driving shaft
also rotates by the same angle, the intermediate piece also rotates by the same angle through
which flange A has rotated.
Due to the rotation of intermediate shaft, the flange B (link 4) connected to the driven shaft,
also rotate by the same angle.
Hence link 2, 4 & 1 have the same angular velocity at every instant.
Naveen Kishore P, Asst. Prof, MED, Mecs.
23. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 24 of 32
1
2
3
4 5
6
A
B
C
D E
C'
C
C''
B''
b
B'
Stroke
E'
E''
MECHANISMS
QUICK – RETURN MECHANISMS
In many applications, mechanisms are used to perform repetitive operations.
In these repetitive operations, there is usually a part of the cycle, when the
mechanism is under load, called working stroke.
The remaining part of the cycle is called as the return stroke.
The mechanism simply returns to repeat the operation without load.
The ratio of the time for the working stroke to the time for return stroke is known as
time ratio.
To produce quick return, the time ration must be greater than unity and as large as
possible.
Quick return mechanisms are used on machine tools to give a slow cutting stroke
and a quick return stroke for a constant angular velocity of the driving crank.
The most commonly used types of quick return mechanisms are
o Drag link mechanism
o Whitworth mechanism
o Crank & Slotted lever Mechanism
Drag link mechanism:
This is four bar mechanism with double crank in which the shortest link is fixed. If the crank
AB rotates at uniform speed, the crank CD will rotate at non-uniform speed. This rotation of
link CD transformed to quick return reciprocatory motion of the ram E by the link CE as shown
in the figure. When the crank AB’ rotate through an angle α in counter clockwise direction
during working stroke, the link CD rotates through 180°. When the crank AB’’ continues to
rotate through the angle β during return stroke, the crank CD rotates through another 180°. We
can observe that b
ˆ
ˆ . Hence time of working stroke is
b
times more or return stroke is
b
times quicker. Shortest link always the stationary link. Sum of the length of shortest and the
longest links of the four links 1, 2, 3 and 4 should be less than the sum of the other two links
length. It is the necessary condition for drag link quick return mechanism.
Whitworth mechanism:
Refer the third inversion of single slider crank chain mechanism.
Naveen Kishore P, Asst. Prof, MED, Mecs.
24. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 25 of 32
Crank & Slotted lever Mechanism:
Refer to the second inversion of single slider crank chain mechanism.
STRAIGHT LINE MOTION MECHANISMS
These are used to produce straight motions.
These mechanisms may produce exactly straight line motion or approximate
straight line motion.
In these mechanisms either only turning pairs are connected or one sliding pair is
used.
Condition for Exact straight line motion mechanisms:
Let O be the centre of a circle of diameter AD.
AB is any chord.
The triangle inscribed on a semi- circle (i.e.Δ ABD) will be right angled
triangle.
The chord produced up to the point C.
From C, draw a line CE perpendicular to the diameter AD produced.
Naveen Kishore P, Asst. Prof, MED, Mecs.
25. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 26 of 32
Then locus of point C will be straight line, perpendicular to the diameter AD,
provided the product of AB×AC is a constant.
Proof: The Δ AEC & Δ ABD are similar as DAB= EAC (common angle) and
ABD= AEC = 90°
Hence,
AE
AB
AC
AD
Or ABAC = ADAE
But AD is the diameter of the circle and hence it is constant. If AE also constant then
ABAC will be a constant when the perpendicular from the point C always coincides
with point E. Hence the projection of C should always be at E.
Peaucellier mechanism:
It consists of eight links i.e. links AO, OE, AB, AD, EB, BC, CD and DE in which
link AO is fixed and the link OE is rotating about point O, as shown in the fig.
Links BC = CD = DE = EB, thus form a rhombus and link AB = AD.
All the links are connected to pin joints.
The pin at E is constrained to move along the circumference of a circle of
diameter AF by means of link OE, thus OA = OE.
As the link OE moves around O, the point C moves in the straight line
perpendicular to AO produced.
Proof:
Since BCDE is a rhombus, the diagonals EC & BD will bisect each other at right
angles. Hence ELB = CLB = 900 .
Also, the AEF will be right angle for all positions of E, as it is angle
subtended by a diameter of the circle on the circumference of the circle.
In ∆AEB & ∆ADE, AB=AD, BE=ED & AE is common. Therefore, these two
triangles are similar.
Hence EAB = EAD. Therefore point E lies on the bisector of DAB…...(1)
Naveen Kishore P, Asst. Prof, MED, Mecs.
26. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 27 of 32
In ∆ACB & ∆ACD, AB=AD, BC=CD & AC is common. Therefore these two
triangles are similar.
Hence CAB=CAD. Therefore, point C lies on the bisector of DAB...........(2)
From (1) & (2), it is clear that AEC is a straight line.
Now in right angled triangle ALB,
AB2 =AL2+LB2 …………………………. (3)
Now in right angled triangle CLB,
BC 2
CL2
LB2
………………………………….. (4)
Subtracting equation (4) from (3), we get
AB2 BC 2 AL2CL2
(ALCL).(ALCL)
AC (ALEL)
ACAE
But AB & AC are of constant lengths; therefore, the product AE×AC remains
constant.
Hence point C traces a straight path perpendicular to the diameter AF produced.
Hence point C moves in a straight line perpendicular to AO produced.
Roberts Mechanism:
This is also a four-bar chain mechanism.
In the mean position, it has the form of trapezium.
The links OC & AD are of equal lengths and link OA is fixed.
A bar EB is rigidly attached to the link CD at the midpoint B of the link CD.
The bar EB is right angle to CD.
The bar EB is at right angle to CD.
The point E is the tracing point.
When the mechanism is displaced as shown in the fig. by the dotted lines, the point
E will trace an approximate straight line.
Naveen Kishore P, Asst. Prof, MED, Mecs.
27. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 28 of 32
INTERMITTENT MOTION MECHANISM
Intermittent motion means that the motion is not continuous but it is ceased at definite
intervals. There are many instances where it is necessary to convert continuous motion into
intermittent motion. One of the examples is the indexing of work table on a machine tool.
Ratchet & Pawl mechanism:
It consists of a ratchet wheel 2 and a pawl as shown in the fig.
When the lever 4 carrying, pawl is raised, the ratchet wheel rotates in counter
clockwise direction (driven by pawl).
As the pawl lever is lowered the pawl slides over the ratchet teeth.
One more pawl 5 is used to prevent the ratchet from reversing.
Application of Ratchet & Pawl mechanism:
i) Used to produce intermittent rotary motion from an oscillating or reciprocating
member.
ii) Used in feed mechanisms, lifting jacks, clocks, watches & counting devices.
Geneva mechanism:
It consists of a driving wheel D carrying a pin which engages in a slot of the
follower F.
The slots are positioned so that the pin enters and leaves them tangentially.
Naveen Kishore P, Asst. Prof, MED, Mecs.
28. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 29 of 32
Thus, advantage of this mechanism is that it provides indexing without
impact loading.
During one quarter revolution of the driving plate, the pin & follower remains in
contact and hence the follower is turned by one quarter turn.
During remaining time of one revolution of driver, the follower remains in at
rest, locked in position by circular arc (locking plate).
Applications: (i) Used to prevent over winding of main springs in clock & watches.
(ii) Feeding the strips of films in a quick advance in early motion
pictures.
(iii) Indexing of a work table on a machine tool.
Toggle Mechanism:
Principle: In slider, crank mechanism, as the crank approaches one of its dead-centre
positions, the movement of the slider approaches zero. The ratio of the crank movement to
the slider movement approaches infinity, which is proportional to the mechanical advantage.
Links CD and CE are of same length.
Resolving the forces at C vertically, we get
2
sin
cos
P
F
Or
tan
2
P
F
Thus for a given value of P, as the links CD & CE approaches collinear position (α→0), the
force F raises rapidly.
Applications: (i) Used where large force acting through short distance is required.
(ii) Used in toggle clamps, riveting machines, punch presses, stone crushers.
(iii) Used in switches, circuit barkers and other mechanisms where snap action is required.
Pantograph or double lever mechanism (oscillatory motion)
It consists of a jointed parallelogram ABCD as shown in the fig.
It is made up of bars connected by turning pairs.
AB = CD & parallel to each other and also AD = BC & parallel to each other.
Naveen Kishore P, Asst. Prof, MED, Mecs.
29. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 30 of 32
Extend any two adjacent AB to O and BC to E, such that the points O & E lies in
the same straight line through the fourth turning pair D. Thus, ODE lies in a
straight line.
Make any point O or E as fixed pivot point. Thus, the pantograph mechanism is
completed.
For all relative positions of the links, the triangles OAD & OBE are similar and
points ODE lie on a straight line.
It can be proved that the point E traces the same path as described by D.
A
B
C
D
E
D'
E'
A' B'
C'
O
Proof: From the similar triangles OAD & OBE, we find that the
BE
AD
OE
OD
OB
OA
Since point O is fixed and the points D & E move to some new position D` & E`. Then,
'
'
OE
OD
OE
OD
A little consideration will show that the straight-line DD’ is parallel to the straight-line
EE’. Hence,
'
'
'
'
EE
DD
OE
OD
OE
OD
Thus, the ratio of lengths OD:OE from the fixed pivot point O remains same as the links
are moved. This is same for all the positions. Hence E traces out the same path as
described by point D, but to a reduced scale by a fixed incorporated ratio.
Uses:
(1) It is used as a geometric instrument to reproduce geometrical figures and plane areas
of irregular shapes such as maps, plans & drawings etc. on enlarged or reduced scales.
(2) Used to guide the cutting tools.
(3) Used as an indicator rig to reproduce the displacement of the cross head of
reciprocating engine mechanism which give the displacement of piston.
Naveen Kishore P, Asst. Prof, MED, Mecs.
30. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 31 of 32
Condition for correct steering in motor cars:
It is a mechanism for changing the direction of motion of two or more wheel axels
with respect to chassis, in order to move the car in any desired path.
The front wheels are mounted on short separate axels which are pivoted to
the chassis of the vehicle.
The rear wheels have a common axel and this is fixed.
Steering is usually effected by turning the axes of rotation of the two front wheels
relative to the chassis of the vehicle.
If the car is making a right turn as shown in the fig., the axis of the right wheel must
swing about pin C through a greater angle than the left wheel about A.
The condition of the good steering is that, the relative motion between the
wheels of the vehicle and the road surface must be one of pure rolling.
To satisfy above condition, the swing of the two axes would be such that their centre
lines extended would always intersect on the centre line of the rear axle at G.
Then all parts of the cars would be moving about the vertical axis through G
and the tendency of the wheels to skid would be reduced to a minimum.
Let, w = wheel base = AE = CF, a = wheel track = AC = EF
From the fig.
AC = EF = EG – FG ………………………………. (1)
From Δ AEG,
tan
EG
EG
tan
AE cot
Similarly from Δ CFG, FG = CF cotθ
Substituting the value of EG and FG in equation (1), we get
AC = AE cot- CF cotθ
a = w cot- w cotθ= w (cot- cotθ)
or
cot- cotθ= a/w → Condition for correct steering
So, for correct steering the steering gear must obey this equation whatever may be the radius
of curvature of the path followed by the car.
AE
AE
Naveen Kishore P, Asst. Prof, MED, Mecs.
31. MODULE 1 KINEMATICS OF MACHINES
Pavana Kumara B, Assistant Professor, SJEC, Mangaluru Page 32 of 32
Ackermann Steering gear:
It consists only of turning pairs and is based on a four bar chain in which two
longer links AB & KL are unequal in length, while the two shorter links AK & BL
are equal in lengths.
As is made up of only turning pairs wear & tear of the parts is less & cheaper.
In the mid position, when the car is moving along the straight path, the link AB &
KL are parallel and the links AK & BL each inclined at an angle to the
longitudinal axis of the car.
When the vehicle steers about the right as shown in the fig., the short link BL
turned so as to increase the , whereas the long link LK causes the other short link
AK to turn so as to reduce .
In the above arrangement, it is clear that the angle through which AK turns is less
than the angle θ through which the BL turns and therefore the left front axle turns
through a smaller angle than the right front axle.
Condition for correct steering in motor cars is
l
b
q
cot
cot .
The value of the obtained for a given value of θ would depend upon the ratio
AK/AB and the angle .
In this mechanism, the instantaneous centre does not lie on the axis of the rare axel,
but on a line parallel to the rear axle axis at an approximate distance of 0.3l
above it.
Three correct steering position will be:
i) when moving straight
ii) When moving one correct angle to the right corresponds to the link ratio
AK/AB and angle .
iii)Similar position when moving to the left.
Naveen Kishore P, Asst. Prof, MED, Mecs.