Hodges Initial Design

Joe Gates Construction, Inc
Trish Hodges
Kitchen Renovation
10/15/2015
John Zierke
jzierke@cliqstudios.com
Direct Line: 952-241-8690

U249024-ROT-4
RR96R
UF330
DB30-2
B
E
R
36-S
S
L
DB18
UF330
BSP09
BSP09
UF330
DB36 DB30-2
FP9648
B30-FH B30-FH B30-FH
BSP12
SB36-TO
BWB18
UF342WR361824
UF336
W1536LW2736WER2436L
W2436
UF336
W153615L W301815L W153615R
UF336
W3036 W3036138"
172"
DW
30" Range
FFOB42-FH
FFOB42-FH

UF336
W1536L
W2736 WER2436L
BER36-SSLDB30-2
UF330
RR96R
U249024-ROT-4
WR361824
UF342
54"18"6"
2 Wood
Lazy Susans
18"
Fridge opening
36" x 72"
4RollOutsTrays
CTM8
TCM8
UF396
138"96"
OGP8

WER2436L
UF336 UF336
W3036 W3036W2436
W153615L
W153615R
W301815L
BSP09
DB18BER36-SSL DB30-2DB36
UF330 BSP09
CTM8
BTK8
TCM8
UF396
30" Range
30" Microhood
18"
Pull-out Storage
2 Wood
Lazy Susans
161
2"
11
2"
54"6" 172"
96"

BSP12
SB36-TO BWB18
BTK8
Trim the FP9648 into two panels for each side of the island
and apply to the 1/4" reveal as skin.
Apply the FFO doors to the FP9648 "on Site"
Tilt
Out
Tray
Pull
Out
Trash
Pull-outStorage
24"Dishwasher

B30-FH B30-FH B30-FH
108 1
4 "
Apply OGP8 along bottom as baseboard
Trim the FP9648 into two panels for each side of the island
and apply to the 1/4" reveal as skin.
Apply the FFO doors to the FP9648 "on Site"
Depth modified to 18"
Full Depth Shelves

Most refrigerators are at least 29-30” in depth and stick out past wall and base cabinets. Below is an
example of how a Wall Refrigerator cabinet can be pulled forward (before a deep refrigerator panel has
been applied) more than 24” away from the wall. Note: Wall Refrigerator cabinet must have at least 3
points (wall, ceiling, adjacent cabinet or support from floor) of secure contact to be installed correctly
and safely.
Pull Refrigerator Cabinet From Wall
Field Install | Finish Panel
ph: 800.576.7930 | fax: 877.675.4394 | customerservice@cliqstudios.com
CliqStudios.com®
, LLC reserves the right to change, modify or discontinue policy and products at any time.
All dimensions are nominal. This drawing is only provided as a reference and CliqStudios.com is not responsible for final installation.

Deep Refrigerator Enclosure
Refrigerators normally extend out from the countertop at least 4"- 6". This diagram depicts how to enclose the
side(s) of a refrigerator with RR96 & FP4896 panels and provide a “built in” look. Dimensions will vary based
on the WR cabinet size. Installer will provide wood blocking and the means to properly secure panels and WR
cabinet to wall and floor. In example below the WR cabinet (24" deep) is being pulled out from wall 6".
Wall
WR Cabinet
RR96L RR96R
Applied
FP4896
(trimmed to fit
all the way to wall)
Applied
FP4896
(trimmed to fit
all the way to wall)
= Blocking to attach panels &
extend WR cabinet from wall
(not provided)
Refrigerator
View: Top, looking down
Refrigerator Return
30" Deep Panel | RR96
page 1 of 2
CliqStudios.com®
Requires panel
to be anchored to the
inside floor - “L” bracket
if no adjacent base cabinet
Requires panel
to be anchored to the
inside floor - “L” bracket
if no adjacent base cabinet

WR Cabinet
WR Cabinet
WR Cabinet
WR Cabinet
adjacent
wall cabinet
adjacent
base cabinet
adjacent
base cabinet
adjacent
wall cabinet
adjacent
base cabinet
adjacent
wall cabinet
refrigerator
refrigerator
adjacent
wall cabinet
Nowoodblockingshown
onthissideshow
=FP4896 trimmed to fit
=RR96L & RR96R
=UF filler
= Wood Blocking
at back
at back
NO WOOD BLOCKING DISPLAYED
SO PANELS CAN BE VIEWED
Refrigerator Return
30" Deep Panel | RR96
page 2 of 2
CliqStudios.com®

Example drawings depict standard depth wall cabinet with
the door and shelves removed.
Installation supports are not provided by CliqStudios.com
manufacturer’s install requirements vary.
WARNING! Cabinet drawing left and below show example wall
cabinet with ¼" reveal and without applied end panels.
¾"
bottom
(½" plywood)
¾"
Ǫ
½"
¾"
side
Cabinet Underhang = ¾" high
Back Panel thickQHVV Ǫ
Side Panel thickness = ½"
Under Wall Cabinet Dimension
For Under Cabinet Lighting
CliqStudios.com®

cabinetfaceframe
cabinetdoor
Cabinet Side
wood blocking
(not provided)
3½"
ceiling
TCM8
¼"
crown molding
moves up/down
along ceiling3"
UF396
Crown Molding
TCM8 | UF396
CliqStudios.com®

CTM8
1½"
CabinetFaceFrame
CabinetDoor
¾"
Light Rail
CTM8 | Horizontal
CliqStudios.com®
Cabinet Side

CliqStudios.com, LLC reserves the right to change, modify or discontinue programs at any time v 1-2015
Because walls are usually not straight, level, square, flush or plumb we recommend the following
accessories to accommodate constrution space imperfections for the floor, wall or ceiling and may have
included them in your order to finish your space.
Attention:
recommended accessories
for your designDreams designed. Dreams delivered.
96" 4½"
UF1.542 1½" 42"
UF1.596 1½" 96"
UF342 3" 42"
UF336 3" 36"
UF330 3" 30"
UF396 3" 96"
UF642 6" 42"
UF696 6" 96"
A B
A
B
¾"
96"
¾"
¾"
IQR8
ƒ Solid hardwood
ƒ Bold line represents finished edge
¾"
96"
¼"
SM8
ƒ Solid hardwood
ƒ Bold line represents
finished edge
ƒ Solid hardwood
ƒ Front & sides finished
back
wall
floor
side
wall
back
wall
floor
gap created
by filler between
cabinet & wall
Inside Quarter Round is more than a decorative accent.
It is installed after the flooring and is primarily used to
cover the gapping resulting from shims to level cabinets.
Quarter Round can also help cover up gaps in the floor -
especially with tile.
side
wall
back
wall
floor
cabinet
side
floor
back
wallside
wall
cabinet
side
FILLERS
Fillers are used to “fill” the gap between a wall and the
end run of cabinets, and sometimes between cabinets.
Fillers can also be used horizontally for decorative
molding applications. Field install and trim to width/height.
Note: Fillers also are used to provide space between
cabinet and wall for proper door swing operation to
provide cabinet access, especially with decorative
hardware and roll out trays
BTK8
ƒ Plywood veneer w/ engineered core
ƒ Bold line represents finished edge
Base ‘Toe Kick’ is used as a panel to cover up
the gapping created by the placement of
cabinets. It is applied to the recessed area
where the cabinet meets the floor.
SM8, or Scribe molding,
is used along the wall when
cabinets/fillers meet a non-plumb
wall to hide gapping between the
cabinet and the wall.
cabinet
side

Wood is a product of nature with different grain patterns, color variations, aging patterns, and mineral
streaks which add to the beauty and distinction of natural hardwood products. These wood variations
are not considered a defect and will not be subject to warranty replacement. Painted Cabinets may
require additional maintenance. Over time, painted finishes will develop hairline cracks from the results
of natural expansion and contraction of the wood.
Visit our website for more information on finish characteristics
Do not begin demolition of space or existing cabinetry prior to receipt and inspection of your new
cabinets, as missing or damaged parts may delay your installation. Any install delays, trip charges,
contractor fees, etc. due to pre-scheduling your installer are your responsibility. CliqStudios.com is not
liable for these costs, and has recommended against installation prior to inspection and receipt of all
original and replacement orders.
measurements
installation
wood & finish characteristics
You have provided, and are responsible for, all measurements. Please verify all dimensions prior to
the purchase of your cabinets:
Any changes made after the order has been placed will be subject to a 25% restocking fee and
additional shipping charges. Visit our website for more information on our Return Policy
At CliqStudios.com, we understand that remodeling projects can be stressful, time consuming, and may
disrupt areas of your home that your rely on. In our experience, making sure that you are aware of what
to expect is the most effective way to navigate the process as smoothly as possible.
Thank you for choosing CliqStudios.com for your cabinetry project!
• Appliances • Window/Door dimensions and location
• Ceiling and/or soffit heights • Special considerations & obstructions
• All drawings, renderings and design information provided by designer
Please read the following carefully prior to the purchase of your order:
what to expect
order confirmation
page 1 of 2
Dreams designed. Dreams delivered.
CliqStudios.com®

terms & conditions
_________________________________ ____________
Customer Signature Date
_________________________________
Customer Printed Name
In placing your order with Cliqstudios.com, you agree that you have read and understand this
documentation, and that you agree to the terms and conditions of Cliqstudios.com.
I have read and I understand the above Cliqstudios.com Final Steps and have verified and
approved all of the conditions, including any drawings, renderings or pictures of design plan, that
were included with the final design packet with designer.
order receipt & inspection
Once order has been received promptly inspect for any damaged or missing items. If you have any
damaged items you will need to contact Customer Service as soon as possible. Replacement orders
usually ship in less than one week.
• phone: 800.576.7930 ext. 561
• email: customerservice@cliqstudios.com
Standard Home Delivery order will be shipped to a location accessible by a pallet jack to the first
secure, dry area (usually a garage), on the same level as the truck tires. If Standard Home Delivery
cannot be accommodated please contact your designer before purchase to arrange for Limited or
Restricted delivery; additional charges will apply. Cliqstudios.com will notify you once the order has left
our facility via email. You will be contacted to schedule an eight (8) hour delivery window directly by
the delivery carrier. Shipments may be delayed due to weather, mechanical issues, holidays, or other
situations relating to delivery coordination.
standard delivery
If you haven’t already please take the time to view our video which outlines what to expect and easy
things that you can do to make the delivery and receipt of your cabinet order go as smoothly as
possible. Visit our website to view deilvery video
To send signature back to designer you may:
1. Scan & email to your designer
2. Fax to 877-675-4394 attention your designer
3. Or reply back via email confirming your agreement to the Terms & Conditions
what to expect
order confirmation
page 2 of 2
Dreams designed. Dreams delivered.
CliqStudios.com®

Hodges Initial Design

More Related Content

What's hot

Viewers also liked

Similar to Hodges Initial Design

Hodges Initial Design