This document describes a student project that aims to generate electrical energy using piezoelectric materials in response to footstep force. The project seeks to address Pakistan's issue of power demand exceeding supply by providing an alternative pollution-free energy source. It will incorporate a piezoelectric transducer, battery, microcontroller, and LCD display. The timeline outlines literature review, software/hardware design, and report writing over several months. The objectives are utilizing wasted human energy through 'crowd energy farms' and generating power without fuel or noise/pollution. The expected outcome is a system that uses footstep voltage to run loads and shows sensor output/battery parameters on an LCD.
Its a free source of energy we know very well man has needed and used energy at an increasing rate for the sustenance and well-being since time immemorial. Due to this a lot of energy resources have been exhausted and wasted. Proposal for the utilization of waste energy of foot power with human locomotion is very much relevant and important for highly populated countries like India where the railway station, temples etc., are overcrowded all round the clock .When the flooring is engineered with piezo electric technology, the electrical energy produced by the pressure is captured by floor sensors and converted to an electrical charge by piezo transducers, then stored and used as a power source. And this power source has many applications as in agriculture, home application and street lighting and as energy source for sensors in remote locations.
Its a free source of energy we know very well man has needed and used energy at an increasing rate for the sustenance and well-being since time immemorial. Due to this a lot of energy resources have been exhausted and wasted. Proposal for the utilization of waste energy of foot power with human locomotion is very much relevant and important for highly populated countries like India where the railway station, temples etc., are overcrowded all round the clock .When the flooring is engineered with piezo electric technology, the electrical energy produced by the pressure is captured by floor sensors and converted to an electrical charge by piezo transducers, then stored and used as a power source. And this power source has many applications as in agriculture, home application and street lighting and as energy source for sensors in remote locations.
Hello Mam,
We are the student of b.tech mechanical engg. we make foot step electricity genarator when we press the top of the project the spring is press the mechanical setup of project is working the rack and pinoin is connect to the shaft is connect to pully is connect to dianoma with help v velt when we pressure the top of the project the rack and pinion is rotating the shaft is rotating to the pully to rotating to dynoma is rotted produce the electricity and we optain the electricity by the system
PROJECT - " PROGRAMMABLE ENERGY METER CALCULATOR"BhanuKhandelwal5
this is my project ppt which i make in 2019 on the topic of "Programable energy auditing equipment for industry for instanteous electrical load survey" which basically calculate the billing of energy meter and send message to mobile cdms and for every unit bill is calculated and message comes
Hello Mam,
We are the student of b.tech mechanical engg. we make foot step electricity genarator when we press the top of the project the spring is press the mechanical setup of project is working the rack and pinoin is connect to the shaft is connect to pully is connect to dianoma with help v velt when we pressure the top of the project the rack and pinion is rotating the shaft is rotating to the pully to rotating to dynoma is rotted produce the electricity and we optain the electricity by the system
PROJECT - " PROGRAMMABLE ENERGY METER CALCULATOR"BhanuKhandelwal5
this is my project ppt which i make in 2019 on the topic of "Programable energy auditing equipment for industry for instanteous electrical load survey" which basically calculate the billing of energy meter and send message to mobile cdms and for every unit bill is calculated and message comes
Design and Construction of a 20 000 Mah Wind Power Bankijtsrd
The study aimed to design and construct a portable wind power bank, using quantitative research method to profoundly explain the concept and define the problems that will make an improvement for the ideas in developing the project. One type of wind powered battery charging will be explored in this paper. This can be used in times of power interruptions, in the absence of electrical sources, during outdoor activities away from home where charging is a necessity, and most specially to save money by minimizing electrical consumption. It is designed to be installed fixed on home rooftops when at home but can be detachable and can be carried whenever necessary. It is an energy saving device for the reason that it may not need any external source of electricity. It consists of a wind turbine driving a generator and operates at variable speed. It consists of three different modules which are power supply module, power storage module and phone charging module. All these modules consist of different components that perform different functions. The power supply module consists of the components' physics, the principles and the design. The power storage module includes the components parameters responsible for the restoration of energy to the battery after it has been used to charge mobile phones. There is connecting port between the power bank power storage and charging module and the phone charging module through which it can be connected in order to recharge phones as well as to recharge the power bank from an AC source. This paper analyzes the property of the system components. The effect of parameter variation and the system configuration on the system performance are investigated. Ramon L. Pitao, Jr. | Sunny E. Araneta | Clifford Jan C. Dionson | Jaypee G. Gagarino | Ronald M. Famor ""Design and Construction of a 20 000 Mah Wind Power Bank"" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-4 , June 2019, URL: https://www.ijtsrd.com/papers/ijtsrd23426.pdf
Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/23426/design-and-construction-of-a-20-000-mah-wind-power-bank/ramon-l-pitao-jr
Market transformation in the energy sector. The implications of battery storage and reducing renewable energy costs to the Australian environment. Presents projections from NREL, DoE, CSIRO, GDF Suez, IRENA and others
Power Generation Using Piezoelectric TransducerIJERA Editor
The most basic need of today’s world is energy which is non-renewable source of energy available on earth. The
need is increasing day by day, to overcome this there is requirement of energy harvesting. This paper attempts
to show how man has been utilizing and optimizing kinetic energy. Current work also illustrates the working
principle of piezoelectric crystal and various sources of vibration for the crystal. “The idea of energy harvesting
is applicable to sensors as well as transducers that are placed and operated on some entities for a long time to
replace the sensor module batteries. Such sensors are commonly called self-powered sensors.” Embarked
piezoelectric transducer, which is an electromechanical converter, undergoes mechanical vibrations therefore
produce electricity. This power source has many applications as in agriculture, home application and street
lighting and as energy source for sensors in remote locations
Self Electricity Generation and Energy Saving By Solar Using Programmable Sys...theijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
Theoretical work submitted to the Journal should be original in its motivation or modeling structure. Empirical analysis should be based on a theoretical framework and should be capable of replication. It is expected that all materials required for replication (including computer programs and data sets) should be available upon request to the authors.
The International Journal of Engineering & Science would take much care in making your article published without much delay with your kind cooperation.
Collecting Economic Data in Power Quality SurveyLeonardo ENERGY
Highlights:
* Presents an approach to facilitate economic data collection.
* Defines Power Quality (PQ) as the extent to which the electrical energy available at the point of use is compatible with the needs of the load equipment connected.
* Lack of compatibility may lead to end user equipment ceasing, operating erratically or incorrectly, or at reduced efficiency.
* Discusses the many parameters necessary for compatibility.
* Presents a checklist for checking the completeness of the methodology.
Similar to Foot Step Power Generation Using piezoelectric material (20)
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Quality defects in TMT Bars, Possible causes and Potential Solutions.PrashantGoswami42
Maintaining high-quality standards in the production of TMT bars is crucial for ensuring structural integrity in construction. Addressing common defects through careful monitoring, standardized processes, and advanced technology can significantly improve the quality of TMT bars. Continuous training and adherence to quality control measures will also play a pivotal role in minimizing these defects.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Democratizing Fuzzing at Scale by Abhishek Aryaabh.arya
Presented at NUS: Fuzzing and Software Security Summer School 2024
This keynote talks about the democratization of fuzzing at scale, highlighting the collaboration between open source communities, academia, and industry to advance the field of fuzzing. It delves into the history of fuzzing, the development of scalable fuzzing platforms, and the empowerment of community-driven research. The talk will further discuss recent advancements leveraging AI/ML and offer insights into the future evolution of the fuzzing landscape.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
Foot Step Power Generation Using piezoelectric material
1. Foot Step Power Generation Using
piezoelectric material
Group Members
1.Muhammad Ajmal
2.Waseem Sarwar
3.Maria Anum
Department of Electrical engineering
Supervisor Engr Awais Masood
APCOMS Insignia
2. Contents
Problem statement
Brief Introduction
Type of project
Literature Review
Block diagram
Tentative Time line
FYP Objective
FYP Outcome
Q &A
3. Problem statement
In Pakistan the demand is more than the daily energy produced so we are
facing power-cut after approximate 1 hour and industries are in hell these
days. People uses rechargeable batteries (UPS) or diesel/petrol engine to
fulfill their demands. The use of stand by generator is common in
industries and large offices.We will generate electrical energy using
piezoelectric material (which convert Mechanical stress into Electrical
Energy) and will control the output with microcontroller.
Problem statement Brief Introduction Type of project Literature Review Block diagram Tentative Time line FYP Objective FYP Outcome Q &A
4. Problem statement Brief Introduction Type of project Literature Review Block diagram Tentative Time line FYP Objective FYP Outcome Q &A
Brief Introduction
This project is used to generate voltage using footstep force. The
proposed system works as a medium to generate power using force.
This project is very useful in public places like bus stands, theaters,
railway stations, shopping malls, etc.
5. Implementation type
60 % hardware
35 % software
5 % research paper
Type of project
Problem statement Brief Introduction Type of project Literature Review Block diagram Tentative Time line FYP Objective FYP Outcome Q &A
6. Literature Review
• Generation of Electrical Power through Foot steps K.Ramakrishna,
Guruswamy Revana and Venu Madhav Gopaka International Journal of
Multidisciplinary and Current Research 20 Sept 2014, Vol.2
• Electrical Power Generation Using Piezoelectric Crystal Anil Kumar,
International Journal of Scientific & Engineering Research Volume 2, Issue
5, May-2011
• Henry A. Sodano, Daniel J. Inman, Gyuhae Park “Estimation of
Electric Charge Output for Piezoelectric Energy Harvesting”,LA-UR-
04-2449, Strain Journal, 40(2), 49-58, 2004
Problem statement Brief Introduction Type of project Literature Review Block diagram Tentative Time line FYP Objective FYP Outcome Q &A
8. Tentative Time line
Months -> Sep Oct Nov Dec Jan Feb Mar Apr May
Literature Review ✔ ✔ ✔ ✔ ✔ ✔
Software design ✔ ✔ ✔ ✔ ✔ ✔ ✔
Controller design ✔ ✔ ✔
Hardware ✔ ✔ ✔ ✔ ✔
Thesis and Report
Writing
✔ ✔ ✔ ✔ ✔ ✔
Problem statement Brief Introduction Type of project Literature Review Block diagram Tentative Time line FYP Objective FYP Outcome Q &A
9. FYP Objective
Human/bio-energy being wasted if
it can be made possible for
utilization it will be great invention
and crowd energy farms will be very
useful energy sources in crowded
countries.
Pollution less generation
Noise less generation
Fuel less
Problem statement Brief Introduction Type of project Literature Review Block diagram Tentative Time line FYP Objective FYP Outcome Q &A
10. FYP Deliverables
This project is used to generate voltage using footstep force.
With the help of this voltage produce will be used to run different loads.
An LCD showing the piezoelectric sensor output and battery parameters
Controller to charge the battery
Problem statement Brief Introduction Type of project Literature Review Block diagram Tentative Time line FYP Objective FYP Outcome Q &A
11. Question & answers??
Problem statement Brief Introduction Type of project Literature Review Block diagram Tentative Time line FYP Objective FYP Outcome Q &A