ECET 405 Entire Course NEW

DERY ECET 405 All Assignments NEW
Check this A+ tutorial guideline at
http://www.uopassignments.com/ecet-405-
devry/ecet-405-all-assignments-recent
For more classes visit
http://www.uopassignments.com
ECET 405 All Assignments NEW
ECET 405 Week 1 iLab NEW
ECET 405 Week 2 Chapter 2 Homework NEW
ECET 405 Week 3 Chapter 4 Homework and Chapter 5 NEW
ECET 405 Week 4 iLab Hardwiring your PLC NEW
ECET 405 Week 5 Homework NEW
ECET 405 Week 5 iLab Traffic Lights NEW
ECET 405 Week 6 iLab Project Design NEW
ECET 405 Week 7 iLab Project Design II NEW

DERY ECET 405 Week 1 iLab NEW
devry/ecet-405-week-1-ilab-recent
A Control Problem with Multiple Inputs and
Outputs
1.Complete Table 1 below per lab instructions
2.Take a digital photo of your completed circuit
and insert it below.
3. In a paragraph write your comments on any
wiring issues or challenges that you encountered.
How did you troubleshoot or fix the problem (if
any)? Was there any flickering of the LEDs when
the motor was running or stopped? If so, how
would you fix the problem?

4. Submit the completed worksheet to week-1 Lab
Dropbox.

DERY ECET 405 Week 2 Chapter 2 Homework NEW
devry/ecet-405-week-2-chapter-2-homework-
recent
Chapter 2 Homework
1)A discrete 120 V ac output module is to be used
to control a 230 V dc solenoid valve. Draw a
diagram showing how this could be accomplished
using an interposing relay.
2)Assume a thermocouple generates a linear
voltage of from 20 mV to 50 mV when the
temperature changes from 750°F to 1250°F. How
much voltage will be generated when the
temperature of the thermocouple is at 1000°F?

5)Assume the triac of an ac output module fails in
the shorted state. How would this affect the device
connected to this output?

1.Per step 6 of Lab 2 instructions, turn on the power supply and touch the loose end of the red wire shown in
Figure 7 to input terminals X0, X1, X2, X3, X4, X5, X6, and X7. Indicate which of LEDs marked X0 to X7 will
turn on.
1.Explain why some of the input LEDs do not turn on as you touch the loose red wire to some of the input
terminals of the PLC.
2.What needs to be done to enable those LEDs that did not turn on, to turn on as you touch the loose end of
the red wire to corresponding input terminals?
3.Explain what you need to do to turn on LEDs X0 and X5 at the same time?
4.Explain what you need to do to turn on LEDs X0, X2, X4, and X6 at the same time?
5.For the software part of the lab answer the following questions:
6.Describe the operation of each instruction in each rung:
7. Describe how you would modify the program so that when overheating occurs for the first time, the entire
process stops

DERY ECET 405 Week 3 Chapter 4 Homework and
Chapter 5 NEW
and-chapter-5-recent
ECET 405 Week 3 Chapter 4 Homework and
Chapter 5 NEW

DERY ECET 405 Week 4 Chapter 7 Homework NEW
recent
Chapter 7, pages 195 - 200, Problems 3, 6, 12
Chapter 8, pages 229-232, Problems 1, 3, 8

DERY ECET 405 Week 4 iLab Hardwiring your PLC
NEW
devry/ecet-405-week-4-ilab-hardwiring-your-
plc-recent
ECET 405 Week 4 iLab Hardwiring your PLC NEW
Hardwiring your PLC, Downloading a Program
Containing Timer and Counter Instructions, and
Running the Process
1.Take a digital photo of your circuit and attach to
this worksheet
2. Print a copy of the ladder logic program from
your PC and attach to this worksheet.
3. Briefly describe the operation of each rung.
The process starts by pressing the NO start
pushbutton and can be stopped at any time by
pressing an NC stop pushbutton. As soon as the

process starts, a DC motor runs for five seconds
and then stops. A LED blinks on/off for every
second the motor runs. Once the motor stops, if the
NO count pushbutton is pressed four times, the
motor turns on again and runs for five more
seconds. A LED blinks on/off for every second the
motor runs. Then, the entire process ends.

DERY ECET 405 Week 5 Homework NEW
devry/ecet-405-week-5-homework-recent
Chapter 10 - PP 298-300:
Chapter 11 - PP 318-321:
Chapter 13 – PP 377-378:

DERY ECET 405 Week 5 iLab Traffic Lights NEW
devry/ecet-405-week-5-ilab-traffic-lights-
recent
ECET 405 Week 5 iLab Traffic Lights NEW
LogixPro Simulation:
1.Copy and paste the ladder logic program you
obtained in step 4 of the lab to this worksheet.
PLC Hardware:
2.Take a digital photo of your PLC wiring and
attach to this worksheet.
3.Print a copy of the ladder logic program and
attach to this worksheet.
4.Briefly describe the operation of each rung for
the ladder logic shown in step 8.

devry/ecet-405-week-6-homework-recent
Chapter 14 problems 1, 2, and 7
Chapter 15 problem 2
Chapter 14
Problem 1: Give an example of an open-loop
control system. Explain why the system is open-
loop, and identify the controller and final control
element.
Problem 2: Give an example of a closed-loop
control system. Explain why the system is closed-
loop, and identify the sensor, controller, and final
control element.

Problem 7: Describe the advantage of a 4 to 20mA
current loop as an input signal compared to a 0 to
5 volt input signal.
Chapter 15
Problem 2: Complete a report on one type of open
communications network. Make use of the
Internet as well as manufacturers literature for
compiling the report.

devry/ecet-405-week-6-ilab-project-design-
recent
ECET 405 Week 6 iLab Project Design NEW

DERY ECET 405 Week 7 iLab Project Design II NEW
devry/ecet-405-week-7-ilab-project-design-ii-
recent
ECET 405 Week 7 iLab Project Design II NEW
1.Fill in the values for voltages applied to the
motor and corresponding speeds from steps 6 and
7 in Table 1.
4.Write a brief report on the functionality of your
system. Describe any troubleshooting or
challenges you experienced during the lab.

ECET 405 Entire Course NEW

Recommended

Recommended

More Related Content

Similar to ECET 405 Entire Course NEW

Similar to ECET 405 Entire Course NEW (20)

More from shyamuopuop

More from shyamuopuop (20)

Recently uploaded

Recently uploaded (20)

ECET 405 Entire Course NEW