Cobalt-entrenched N-, O-, and S-tridoped carbons as efficient multifunctional sustainable catalysts for base-free selective oxidative esterification of alcohols
The document summarizes the synthesis and characterization of a cobalt-entrenched nitrogen-, oxygen-, and sulfur-tridoped carbon catalyst (Co@NOSC) for the base-free selective oxidative esterification of alcohols. The Co@NOSC catalyst was prepared via one-step pyrolysis of carrageenan, urea, and cobalt nitrate, resulting in a cobalt nanoparticle core surrounded by a nitrogen-, oxygen-, and sulfur-rich carbon shell. Characterization showed the catalyst had a cobalt content of 20.89 wt%. The Co@NOSC catalyst achieved excellent conversions (up to 97%) and selectivities (up to 99%) for the base-free oxidative esterification of various al
Cobalt-entrenched N-, O-, and S-tridoped carbons as efficient multifunctional...Pawan Kumar
We report the synthesis of sustainable and reusable non-noble transition-metal (cobalt) nanocatalysts
containing N-, O-, and S-tridoped carbon nanotube (Co@NOSC) composites. The expensive and benign
carrageenan served as the source of carbon, oxygen, and sulfur, whereas urea served as the nitrogen
source. The material was prepared via direct mixing of precursors and freeze-drying followed by carbonization
under nitrogen at 900 °C. Co@NOSC catalysts comprising a Co inner core and outer electron-rich
heteroatom-doped carbon shell were thoroughly characterized using various techniques, namely, TEM,
HRTEM, STEM elemental mapping, XPS, BET, and ICP-MS. The utility of the Co@NOSC catalyst was
explored for base-free selective oxidative esterification of alcohols to the corresponding esters under
mild reaction conditions; excellent conversions (up to 97%) and selectivities (up to 99%) were discerned.
Furthermore, the substrate scope was explored for the cross-esterification of benzyl alcohol with longchain
alcohols (up to 98%) and lactonization of diols (up to 68%). The heterogeneous nature and stability
of the catalyst facilitated by its ease of separation for long-term performance and recycling studies
showed that the catalyst was robust and remained active even after six recycling experiments.
EPR measurements were performed to deduce the reaction mechanism in the presence of POBN
(α-(4-pyridyl-1-oxide)-N-tert-butylnitrone) as a spin-trapping agent, which confirmed the formation of
•CH2OH radicals and H• radicals, wherein the solvent plays an active role in a nonconventional manner.
A plausible mechanism was proposed for the oxidative esterification of alcohols on the basis of EPR
findings. The presence of a cobalt core along with cobalt oxide and the electron-rich N-, O-, and
S-doped carbon shell displayed synergistic effects to afford good to excellent yields of products.
A closed loop ammonium salt system for recovery of high-purity lead tetroxide...Ary Assuncao
This document describes a closed-loop hydrometallurgical process for recovering high-purity lead tetroxide from spent lead-acid battery paste. The process involves leaching the paste with a mixed solution of ammonium acetate, acetic acid, and hydrogen peroxide. The leachate is then reacted with ammonium carbonate to precipitate lead carbonate. Impurities are removed during leaching and precipitation. The regenerated leachate is recycled for the next leaching. Lead carbonate is calcined to produce lead tetroxide with low impurity levels meeting industry standards. This process allows for reagent recirculation and production of a high value lead recovery product.
2021 influence of basic carbon additives on the electrochemical performance ...Ary Assuncao
This study investigates the effect of carbon surface basicity on the electrochemical performance and dynamic charge acceptance of lead-carbon batteries. Five activated carbons with different pH values ranging from 9.5 to 11.1 were prepared by ammonia and hydrogen gas treatments. Cyclic voltammetry showed that the hydrogen evolution reaction activity increased with higher carbon surface basicity. Testing of lead-carbon electrodes found a correlation between carbon pH and dynamic charge acceptance, with higher pH carbons showing improved charge currents and final dynamic charge acceptance. The carbon content also affected charge currents during simulated microcycles, demonstrating that surface chemistry and amount of carbon additive both influence the electrochemical properties and performance of lead-carbon batteries.
Maiyalagan,Performance of carbon nanofiber supported pd ni catalysts for elec...kutty79
Carbon nanofibers (CNF) supported Pd–Ni nanoparticles have been prepared by chemical reduction
with NaBH4 as a reducing agent. The Pd–Ni/CNF catalysts were characterized by X-ray diffraction
(XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electrochemical
voltammetry analysis. TEM showed that the Pd–Ni particles were quite uniformly distributed on the
surface of the carbon nanofiber with an average particle size of 4.0 nm. The electro-catalytic activity of
the Pd–Ni/CNF for oxidation of ethanol was examined by cyclic voltammetry (CV). The onset potential
was 200mV lower and the peak current density four times higher for ethanol oxidation for Pd–Ni/CNF
compared to that for Pd/C. The effect of an increase in temperature from 20 to 60 ◦C had a great effect on
increasing the ethanol oxidation activity
The document provides an update on the CoLaBATS project, which aims to develop an innovative process for recovering metals from lithium-ion battery waste using ionic liquids and ultrasonic treatment. It summarizes that a technical meeting was held in May 2014 where an 11-step process design was proposed. It also previews upcoming milestones and events for disseminating project results.
Visible light assisted reduction of nitrobenzenes using Fe(bpy)3+2/rGOnanocom...Pawan Kumar
Visible-light-induced photocatalytic reduction of aromatic nitrobenzenes to the corresponding anilinesat room temperature using reduced graphene oxide (rGO) immobilized iron(II) bipyridine complex asphotocatalyst is described. The rGO-immobilized iron catalyst exhibited superior catalytic activity thanhomogeneous iron(II) bipyridine complex and much higher than metal free rGO photocatalysts. Theheterogeneous photocatalyst was found to be robust and could easily be recovered and reused for severalruns without any significant loss in photocatalytic activity.
Water-splitting photoelectrodes consisting of heterojunctions of carbon nitri...Pawan Kumar
Quinary and senary non-stoichiometric double perovskites such as Ba2Ca0.66Nb1.34-xFexO6-δ (BCNF) have been utilized for gas sensing, solid oxide fuel cells and thermochemical CO2 reduction. Herein, we examined their potential as narrow bandgap semiconductors for use in solar energy harvesting. A cobalt co-doped BCNF, Ba2Ca0.66Nb0.68Fe0.33Co0.33O6-δ (BCNFCo), exhibited an optical absorption edge at ~ 800 nm, p-type conduction and a distinct photoresponse upto 640 nm while demonstrating high thermochemical stability. A nanocomposite of BCNFCo and g-C3N4 (CN) was prepared via a facile solvent assisted exfoliation/blending approach using dichlorobenzene and glycerol at a moderate temperature. The exfoliation of g-C3N4 followed by wrapping on perovskite established an effective heterojunction between the materials for charge separation. The conjugated 2D sheets of CN enabled better charge migration resulting in increased photoelectrochemical performance. A blend composed of 40 wt% perovskite and CN performed optimally, whilst achieving a photocurrent density as high as 1.5 mA cm-2 for sunlight-driven water-splitting with a Faradaic efficiency as high as ~ 88%.
2014 Journal of Power Sources 247 (2014) 572-578Alexis B. B
The document summarizes research on the durability of a nickelealuminum layered double hydroxide/carbon (NieAl LDH/C) composite as a cathode material in nickel metal hydride batteries. The composite was prepared using a liquid phase deposition method and optimized to contain 19.2 mol% aluminum. Electrochemical testing was conducted over 869 charge/discharge cycles at two different current regimes: 5 mA for 300 cycles in half-cell conditions and 5.8 mA for 569 cycles in battery regime. The composite exhibited good lifespan and stability, maintaining a capacity retention above 380 mAh/g. Cyclic voltammetry and X-ray diffraction analysis showed that the a-Ni
Cobalt-entrenched N-, O-, and S-tridoped carbons as efficient multifunctional...Pawan Kumar
We report the synthesis of sustainable and reusable non-noble transition-metal (cobalt) nanocatalysts
containing N-, O-, and S-tridoped carbon nanotube (Co@NOSC) composites. The expensive and benign
carrageenan served as the source of carbon, oxygen, and sulfur, whereas urea served as the nitrogen
source. The material was prepared via direct mixing of precursors and freeze-drying followed by carbonization
under nitrogen at 900 °C. Co@NOSC catalysts comprising a Co inner core and outer electron-rich
heteroatom-doped carbon shell were thoroughly characterized using various techniques, namely, TEM,
HRTEM, STEM elemental mapping, XPS, BET, and ICP-MS. The utility of the Co@NOSC catalyst was
explored for base-free selective oxidative esterification of alcohols to the corresponding esters under
mild reaction conditions; excellent conversions (up to 97%) and selectivities (up to 99%) were discerned.
Furthermore, the substrate scope was explored for the cross-esterification of benzyl alcohol with longchain
alcohols (up to 98%) and lactonization of diols (up to 68%). The heterogeneous nature and stability
of the catalyst facilitated by its ease of separation for long-term performance and recycling studies
showed that the catalyst was robust and remained active even after six recycling experiments.
EPR measurements were performed to deduce the reaction mechanism in the presence of POBN
(α-(4-pyridyl-1-oxide)-N-tert-butylnitrone) as a spin-trapping agent, which confirmed the formation of
•CH2OH radicals and H• radicals, wherein the solvent plays an active role in a nonconventional manner.
A plausible mechanism was proposed for the oxidative esterification of alcohols on the basis of EPR
findings. The presence of a cobalt core along with cobalt oxide and the electron-rich N-, O-, and
S-doped carbon shell displayed synergistic effects to afford good to excellent yields of products.
A closed loop ammonium salt system for recovery of high-purity lead tetroxide...Ary Assuncao
This document describes a closed-loop hydrometallurgical process for recovering high-purity lead tetroxide from spent lead-acid battery paste. The process involves leaching the paste with a mixed solution of ammonium acetate, acetic acid, and hydrogen peroxide. The leachate is then reacted with ammonium carbonate to precipitate lead carbonate. Impurities are removed during leaching and precipitation. The regenerated leachate is recycled for the next leaching. Lead carbonate is calcined to produce lead tetroxide with low impurity levels meeting industry standards. This process allows for reagent recirculation and production of a high value lead recovery product.
2021 influence of basic carbon additives on the electrochemical performance ...Ary Assuncao
This study investigates the effect of carbon surface basicity on the electrochemical performance and dynamic charge acceptance of lead-carbon batteries. Five activated carbons with different pH values ranging from 9.5 to 11.1 were prepared by ammonia and hydrogen gas treatments. Cyclic voltammetry showed that the hydrogen evolution reaction activity increased with higher carbon surface basicity. Testing of lead-carbon electrodes found a correlation between carbon pH and dynamic charge acceptance, with higher pH carbons showing improved charge currents and final dynamic charge acceptance. The carbon content also affected charge currents during simulated microcycles, demonstrating that surface chemistry and amount of carbon additive both influence the electrochemical properties and performance of lead-carbon batteries.
Maiyalagan,Performance of carbon nanofiber supported pd ni catalysts for elec...kutty79
Carbon nanofibers (CNF) supported Pd–Ni nanoparticles have been prepared by chemical reduction
with NaBH4 as a reducing agent. The Pd–Ni/CNF catalysts were characterized by X-ray diffraction
(XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electrochemical
voltammetry analysis. TEM showed that the Pd–Ni particles were quite uniformly distributed on the
surface of the carbon nanofiber with an average particle size of 4.0 nm. The electro-catalytic activity of
the Pd–Ni/CNF for oxidation of ethanol was examined by cyclic voltammetry (CV). The onset potential
was 200mV lower and the peak current density four times higher for ethanol oxidation for Pd–Ni/CNF
compared to that for Pd/C. The effect of an increase in temperature from 20 to 60 ◦C had a great effect on
increasing the ethanol oxidation activity
The document provides an update on the CoLaBATS project, which aims to develop an innovative process for recovering metals from lithium-ion battery waste using ionic liquids and ultrasonic treatment. It summarizes that a technical meeting was held in May 2014 where an 11-step process design was proposed. It also previews upcoming milestones and events for disseminating project results.
Visible light assisted reduction of nitrobenzenes using Fe(bpy)3+2/rGOnanocom...Pawan Kumar
Visible-light-induced photocatalytic reduction of aromatic nitrobenzenes to the corresponding anilinesat room temperature using reduced graphene oxide (rGO) immobilized iron(II) bipyridine complex asphotocatalyst is described. The rGO-immobilized iron catalyst exhibited superior catalytic activity thanhomogeneous iron(II) bipyridine complex and much higher than metal free rGO photocatalysts. Theheterogeneous photocatalyst was found to be robust and could easily be recovered and reused for severalruns without any significant loss in photocatalytic activity.
Water-splitting photoelectrodes consisting of heterojunctions of carbon nitri...Pawan Kumar
Quinary and senary non-stoichiometric double perovskites such as Ba2Ca0.66Nb1.34-xFexO6-δ (BCNF) have been utilized for gas sensing, solid oxide fuel cells and thermochemical CO2 reduction. Herein, we examined their potential as narrow bandgap semiconductors for use in solar energy harvesting. A cobalt co-doped BCNF, Ba2Ca0.66Nb0.68Fe0.33Co0.33O6-δ (BCNFCo), exhibited an optical absorption edge at ~ 800 nm, p-type conduction and a distinct photoresponse upto 640 nm while demonstrating high thermochemical stability. A nanocomposite of BCNFCo and g-C3N4 (CN) was prepared via a facile solvent assisted exfoliation/blending approach using dichlorobenzene and glycerol at a moderate temperature. The exfoliation of g-C3N4 followed by wrapping on perovskite established an effective heterojunction between the materials for charge separation. The conjugated 2D sheets of CN enabled better charge migration resulting in increased photoelectrochemical performance. A blend composed of 40 wt% perovskite and CN performed optimally, whilst achieving a photocurrent density as high as 1.5 mA cm-2 for sunlight-driven water-splitting with a Faradaic efficiency as high as ~ 88%.
2014 Journal of Power Sources 247 (2014) 572-578Alexis B. B
The document summarizes research on the durability of a nickelealuminum layered double hydroxide/carbon (NieAl LDH/C) composite as a cathode material in nickel metal hydride batteries. The composite was prepared using a liquid phase deposition method and optimized to contain 19.2 mol% aluminum. Electrochemical testing was conducted over 869 charge/discharge cycles at two different current regimes: 5 mA for 300 cycles in half-cell conditions and 5.8 mA for 569 cycles in battery regime. The composite exhibited good lifespan and stability, maintaining a capacity retention above 380 mAh/g. Cyclic voltammetry and X-ray diffraction analysis showed that the a-Ni
Synthesis and Characterization of Zinc Phthalocyanine-Cellulose Nanocrystal (...Pawan Kumar
We report highly fluorescent cellulose nanocrystals (CNCs) formed by conjugating a carboxylated zinc phthalocyanine (ZnPc) to two different types of CNCs. The conjugated nanocrystals (henceforth called ZnPc@CNCs) were bright green in color and exhibited absorption and emission maxima at ∼690 and ∼715 nm, respectively. The esterification protocol employed to covalently bind carboxylated ZnPc to surface hydroxyl group rich CNCs was expected to result in a monolayer of ZnPc on the surface of the CNCs. However, dynamic light scattering (DLS) studies indicated a large increase in the hydrodynamic radius of CNCs following conjugation to ZnPc, which suggests the binding of multiple ZnPc molecular layers on the CNC surface. This binding could be through co-facial π-stacking of ZnPc, where ZnPc metallophthalocyanine rings are horizontal to the CNC surface. The other possible binding mode would give rise to conjugated systems where ZnPc metallophthalocyanine rings are oriented vertically on the CNC surface. Density functional theory based calculations showed stable geometry following the conjugation protocol that involved covalently attached ester bond formation. The conjugates demonstrated superior performance for potential sensing applications through higher photoluminescence quenching capabilities compared to pristine ZnPc.
The document summarizes research on the electrochemical deposition of lead dioxide nanostructured thin films. Key findings include:
- Lead dioxide nanostructures were successfully deposited on gold-coated substrates by anodic electrochemical deposition using nitric acid and lead chloride as reactants. The morphology was influenced by deposition parameters like potential, temperature, and pH.
- Deposition at higher temperatures (60°C vs room temperature) resulted in faster growth rates and denser nanostructures, as seen by SEM images.
- Both anodic and cathodic deposition were studied. Cathodic deposition allowed formation of different lead oxide phases depending on conditions, while anodic deposition selectively formed PbO2.
- The work provides a
Synthesis and optimisation of ir o2 electrocatalysts by adams fusion method f...materials87
The document describes the synthesis and optimization of iridium dioxide (IrO2) electrocatalysts for oxygen evolution reaction (OER) in solid polymer electrolyte electrolyzers. IrO2 was synthesized using an Adams fusion method by varying synthesis duration (0.5-4 hours) and temperature (250-500°C). Characterization showed that increasing synthesis time and temperature improved crystallinity and increased particle size. Electrochemical testing revealed that IrO2 synthesized for 2 hours at 350°C exhibited the best electrocatalytic activity toward OER compared to a commercial IrO2 catalyst. Higher temperatures and longer times favored larger, more crystalline particles but decreased surface area and activity.
Synthesis and optimisation of ir o2 electrocatalysts by adams fusion method f...sudesh789
This document discusses the synthesis and optimization of iridium dioxide (IrO2) electrocatalysts for use in solid polymer electrolyte electrolyzers through an adaptation of the Adams fusion method. The synthesis duration and temperature were varied to determine their effect on the physical and electrochemical properties of the IrO2 catalysts. X-ray diffraction analysis showed that increasing the synthesis duration and temperature increased the crystallinity and particle size of the IrO2. Chronoamperometry testing revealed that a synthesis of 2 hours at 350°C produced an IrO2 catalyst with better electrocatalytic activity for oxygen evolution than a commercial IrO2 catalyst.
IrO2 as an anodic electrocatalyst for the oxygen evolution reaction (OER) in solid polymer electrolyte (SPE)
electrolysers was synthesised by adapting the Adams fusion method. Optimisation of the IrO2 electrocatalyst was achieved
by varying the synthesis duration (0.5 – 4 hours) and temperature (250 - 500°C). The physical properties of the
electrocatalysts were characterised by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and
x-ray diffraction (XRD). Electrochemical characterisation of the electrocatalysts toward the OER was evaluated by
chronoamperometry (CA). CA analysis revealed the best electrocatalytic activity towards the OER for IrO2 synthesised
for 2 hours at 350oC which displayed a better electrocatalytic activity than the commercial IrO2 electrocatalyst used in this
study. XRD and TEM analyses revealed an increase in crystallinity and average particle size with increasing synthesis
duration and temperature which accounted for the decreasing electrocatalytic activity. At 250°C the formation of an active
IrO2 electrocatalyst was not favoured.
N-doped graphene quantum dots (NGQDs) catalyze the efficient electrochemical reduction of carbon dioxide into multi-carbon hydrocarbons and oxygenates such as ethylene, ethanol, and n-propanol. The NGQDs achieve high total faradaic efficiencies of up to 90% for carbon dioxide reduction, with selectivities for ethylene and ethanol conversions reaching 45%. Control experiments confirm the NGQDs are responsible for catalyzing the reaction. Compared to undoped graphene quantum dots, the NGQDs have higher activity and selectivity for producing valuable fuel and chemical products from carbon dioxide due to the presence of pyridinic nitrogen defects introduced during synthesis.
This document summarizes research on using various catalysts to promote the dehydrogenation of cyclohexane to produce hydrogen gas. Key findings include:
- Monometallic silver (Ag) catalysts supported on activated carbon cloth showed increasing hydrogen evolution rates with increasing Ag loading up to 10 wt%, but rates decreased at 15 wt% loading likely due to poorer dispersion.
- Bimetallic catalysts with 1 wt% noble metals (platinum, palladium, rhodium) promoted on 10 wt% Ag/ACC showed enhanced hydrogen evolution rates compared to the monometallic Ag catalyst. In particular, a 10 wt% Ag-1 wt% Pt catalyst produced hydrogen at twice the rate of the 10 wt%
This document describes a hydrometallurgical process for recovering rare earth elements from spent nickel-metal hydride batteries. The process involves three steps:
1) Leaching electrode materials from the batteries in sulfuric acid solutions using ozone as the oxidant, which achieved over 90% recovery of lanthanum, cerium, and neodymium.
2) Separating cobalt and part of the nickel from the leach solution using electrodeposition in an electrochemical reactor.
3) Precipitating the remaining rare earth elements along with the rest of the nickel by adjusting the pH of the solution.
Carbon-cuprous oxide composite nanoparticles
were chemically deposited on surface of thin glass tubes of spent
energy saving lamps for solar heat collection. Carbon was
obtained from fly ash of heavy oil incomplete combustion in
electric power stations. Impurities in the carbon were removed by
leaching with mineral acids. The mineral free-carbon was then
wet ground to have a submicron size. After filtration, it was
reacted with concentrated sulfuric/fuming nitric acid mixture on
cold for 3-4 days. Potassium chlorate was then added drop wise on
hot conditions to a carbon slurry followed by filtration.
Nanocarbon sample was mixed with 5% by weight PVA to help
adhesion to the glass surface. Carbon so deposited was doped with
copper nitrate solution. After dryness, the carbon/copper nitrate
film was dipped in hydrazine hydrate to form cuprous oxide -
carbon composite, It was then roasted at 380-400 °C A heat
collector testing assembly was constructed of 5 glass coils
connected in series with a total surface area of 1250 cm2
. Heat
collection was estimated by water flowing in the glass coils that
are coated with the carbon/copper film,. Parameters affecting the
solar collection efficiency such as time of exposure and mass flow
rate of the water were studied. Results revealed that the prepared
glass coil has proven successful energy collector for solar heat.
Synthesis of flower-like magnetite nanoassembly: Application in the efficient...Pawan Kumar
A facile approach for the synthesis of magnetite microspheres with flower-like morphology is reported
that proceeds via the reduction of iron(III) oxide under a hydrogen atmosphere. The ensuing magnetic
catalyst is well characterized by XRD, FE-SEM, TEM, N2 adsorption-desorption isotherm, and
Mössbauer spectroscopy and explored for a simple yet efficient transfer hydrogenation reduction of a
variety of nitroarenes to respective anilines in good to excellent yields (up to 98%) employing hydrazine
hydrate. The catalyst could be easily separated at the end of a reaction using an external magnet and
can be recycled up to 10 times without any loss in catalytic activity.
Effects of Precipitation pH Values on the Electrochemical Properties of β-Nic...iosrjce
IOSR Journal of Applied Chemistry (IOSR-JAC) is a double blind peer reviewed International Journal that provides rapid publication (within a month) of articles in all areas of applied chemistry and its applications. The journal welcomes publications of high quality papers on theoretical developments and practical applications in Chemical Science. Original research papers, state-of-the-art reviews, and high quality technical notes are invited for publications.
Maiyalagan, Synthesis and electro catalytic activity of methanol oxidation on...kutty79
Template synthesis of various nitrogen containing carbon nanotubes using different nitrogen containing polymers and the variation of nitrogen
content in carbon nanotube (CNT) on the behaviour of supported Pt electrodes in the anodic oxidation of methanol in direct methanol fuel cells was
investigated. Characterizations of the as-prepared catalysts are investigated by electron microscopy and electrochemical analysis. The catalyst with
N-containing CNT as a support exhibits a higher catalytic activity than that carbon supported platinum electrode and CNT supported electrodes.
The N-containing CNT supported electrodes with 10.5% nitrogen content show a higher catalytic activity compared to other N-CNT supported
electrodes. This could be due to the existence of additional active sites on the surface of the N-containing CNT supported electrodes, which favours
better dispersion of Pt particles. Also, the strong metal-support interaction plays a major role in enhancing the catalytic activity for methanol
oxidation.
This summarizes a document describing research on using boron-doped diamond (BDD) electrochemical reactors to treat polluted waters. Key points:
1) BDD electrodes have been used in various bench-scale electrochemical reactors, including undivided flow cells and trickle tower reactors, to degrade organic pollutants via electrochemical oxidation.
2) The BDD surface generates reactive oxygen species like hydroxyl radicals that can fully mineralize organic contaminants into CO2 and water. Operating parameters like current density and flow rate influence degradation rates.
3) Studies show these BDD reactors can achieve high removals of chemical oxygen demand (COD) and total organic carbon (TOC) for
Theoretical study of two dimensional Nano sheet for gas sensing applicationvivatechijri
This study is focus on various two dimensional material for sensing various gases with theoretical
view for new research in gas sensing application. In this paper we review various two dimensional sheet such as
Graphene, Boron Nitride nanosheet, Mxene and their application in sensing various gases present in the
atmosphere.
This document summarizes the synthesis, characterization, and evaluation of various IrO2-based binary metal oxide electrocatalysts for the oxygen evolution reaction. IrO2, IrxRu1-xO2, IrxSnx-1O2 and IrxTax-1O2 (where x is between 1 and 0.7) were synthesized via an adapted Adams fusion method. X-ray diffraction and electron microscopy showed the materials formed nanocrystalline solid solutions. Electrochemical testing found that adding RuO2, SnO2, or Ta2O5 to IrO2 improved its catalytic performance for oxygen evolution. Specifically, Ir0.7Ru0.3O2 exhibited the best
Recent progress on reduced graphene oxide....suresh kannan
The document summarizes recent progress on using reduced graphene oxide (rGO)-based materials as counter electrodes for dye-sensitized solar cells (DSSCs) as a cost-effective alternative to platinum. It discusses how rGO on its own is not effective as a counter electrode but that adding metal nanoparticles to rGO composites improves their catalytic activity and performance in DSSCs. The document reviews various rGO composites that have been studied, including those with silver, nickel, tungsten and platinum nanoparticles, as well as metal oxides and dichalcogenides. It compares the photovoltaic parameters of DSSCs using these rGO composite counter electrodes to those using conventional platinum counter electrodes
Reduced graphene oxide–CuO nanocomposites for photocatalyticconversion of CO2...Pawan Kumar
Reduced graphene oxide (rGO)–copper oxide nanocomposites are prepared by covalent grafting of CuOnanorods on the rGO skeleton. Chemical and structural features of rGO–CuO nanocomposites are probedby FTIR, XPS, XRD and HRTEM analyses. Photocatalytic potential of rGO–CuO nanocomposites is exploredfor reduction of CO2into the methanol under the visible light irradiation. The breadth of CuO nanorods andthe oxidation state of Cu in the rGO–CuO/Cu2O nanocomposites are systematically varied to investigatetheir photocatalytic activities. The pristine CuO nanorods exhibited very low photocatalytic activity owingto fast recombination of charge carriers and yielded 175 mol g−1methanol, whereas rGO–Cu2O andrGO–CuO exhibited significantly improved photocatalytic activities and yielded five (862 mol g−1) andseven (1228 mol g−1) folds methanol, respectively. The superior photocatalytic activity of CuO in therGO–CuO nanocomposites was attributed to slow recombination of charge carriers and efficient transferof photo-generated electrons through the rGO skeleton. This study further excludes the use of scavengingdonor.
Reduced graphene oxide–CuO nanocomposites for photocatalyticconversion of CO2...Pawan Kumar
tReduced graphene oxide (rGO)–copper oxide nanocomposites are prepared by covalent grafting of CuOnanorods on the rGO skeleton. Chemical and structural features of rGO–CuO nanocomposites are probedby FTIR, XPS, XRD and HRTEM analyses. Photocatalytic potential of rGO–CuO nanocomposites is exploredfor reduction of CO2into the methanol under the visible light irradiation. The breadth of CuO nanorods andthe oxidation state of Cu in the rGO–CuO/Cu2O nanocomposites are systematically varied to investigatetheir photocatalytic activities. The pristine CuO nanorods exhibited very low photocatalytic activity owingto fast recombination of charge carriers and yielded 175 mol g−1methanol, whereas rGO–Cu2O andrGO–CuO exhibited significantly improved photocatalytic activities and yielded five (862 mol g−1) andseven (1228 mol g−1) folds methanol, respectively. The superior photocatalytic activity of CuO in therGO–CuO nanocomposites was attributed to slow recombination of charge carriers and efficient transferof photo-generated electrons through the rGO skeleton. This study further excludes the use of scavengingdonor.
Performance of carbon nanofiber supported pd–ni catalysts for electro oxidati...suresh899
Carbon nanofibers (CNF) supported Pd–Ni nanoparticles have been prepared by chemical reduction
with NaBH4 as a reducing agent. The Pd–Ni/CNF catalysts were characterized by X-ray diffraction
(XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electrochemical
voltammetry analysis. TEM showed that the Pd–Ni particles were quite uniformly distributed on the
surface of the carbon nanofiber with an average particle size of 4.0 nm. The electro-catalytic activity of
the Pd–Ni/CNF for oxidation of ethanol was examined by cyclic voltammetry (CV). The onset potential
was 200mV lower and the peak current density four times higher for ethanol oxidation for Pd–Ni/CNF
compared to that for Pd/C. The effect of an increase in temperature from 20 to 60 ◦C had a great effect on
increasing the ethanol oxidation activity.
Performance of carbon nanofiber supported pd ni catalysts for electro-oxidati...Science Padayatchi
This document summarizes a study on carbon nanofiber (CNF) supported Pd-Ni catalysts for electro-oxidation of ethanol in alkaline medium. Pd-Ni/CNF catalysts were prepared by chemical reduction and characterized using various techniques. Electrochemical analysis showed the Pd-Ni/CNF catalyst had lower onset potential and 4 times higher peak current density for ethanol oxidation compared to Pd/C. Increasing the temperature from 20 to 60°C greatly enhanced the ethanol oxidation activity of Pd-Ni/CNF.
Performance of carbon nanofiber supported pd–ni catalysts for electro oxidati...sunilove
Carbon nanofibers (CNF) supported Pd–Ni nanoparticles have been prepared by chemical reduction
with NaBH4 as a reducing agent. The Pd–Ni/CNF catalysts were characterized by X-ray diffraction
(XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electrochemical
voltammetry analysis. TEM showed that the Pd–Ni particles were quite uniformly distributed on the
surface of the carbon nanofiber with an average particle size of 4.0 nm. The electro-catalytic activity of
the Pd–Ni/CNF for oxidation of ethanol was examined by cyclic voltammetry (CV). The onset potential
was 200mV lower and the peak current density four times higher for ethanol oxidation for Pd–Ni/CNF
compared to that for Pd/C. The effect of an increase in temperature from 20 to 60 ◦C had a great effect on
increasing the ethanol oxidation activity.
Synthesis and Characterization of Zinc Phthalocyanine-Cellulose Nanocrystal (...Pawan Kumar
We report highly fluorescent cellulose nanocrystals (CNCs) formed by conjugating a carboxylated zinc phthalocyanine (ZnPc) to two different types of CNCs. The conjugated nanocrystals (henceforth called ZnPc@CNCs) were bright green in color and exhibited absorption and emission maxima at ∼690 and ∼715 nm, respectively. The esterification protocol employed to covalently bind carboxylated ZnPc to surface hydroxyl group rich CNCs was expected to result in a monolayer of ZnPc on the surface of the CNCs. However, dynamic light scattering (DLS) studies indicated a large increase in the hydrodynamic radius of CNCs following conjugation to ZnPc, which suggests the binding of multiple ZnPc molecular layers on the CNC surface. This binding could be through co-facial π-stacking of ZnPc, where ZnPc metallophthalocyanine rings are horizontal to the CNC surface. The other possible binding mode would give rise to conjugated systems where ZnPc metallophthalocyanine rings are oriented vertically on the CNC surface. Density functional theory based calculations showed stable geometry following the conjugation protocol that involved covalently attached ester bond formation. The conjugates demonstrated superior performance for potential sensing applications through higher photoluminescence quenching capabilities compared to pristine ZnPc.
The document summarizes research on the electrochemical deposition of lead dioxide nanostructured thin films. Key findings include:
- Lead dioxide nanostructures were successfully deposited on gold-coated substrates by anodic electrochemical deposition using nitric acid and lead chloride as reactants. The morphology was influenced by deposition parameters like potential, temperature, and pH.
- Deposition at higher temperatures (60°C vs room temperature) resulted in faster growth rates and denser nanostructures, as seen by SEM images.
- Both anodic and cathodic deposition were studied. Cathodic deposition allowed formation of different lead oxide phases depending on conditions, while anodic deposition selectively formed PbO2.
- The work provides a
Synthesis and optimisation of ir o2 electrocatalysts by adams fusion method f...materials87
The document describes the synthesis and optimization of iridium dioxide (IrO2) electrocatalysts for oxygen evolution reaction (OER) in solid polymer electrolyte electrolyzers. IrO2 was synthesized using an Adams fusion method by varying synthesis duration (0.5-4 hours) and temperature (250-500°C). Characterization showed that increasing synthesis time and temperature improved crystallinity and increased particle size. Electrochemical testing revealed that IrO2 synthesized for 2 hours at 350°C exhibited the best electrocatalytic activity toward OER compared to a commercial IrO2 catalyst. Higher temperatures and longer times favored larger, more crystalline particles but decreased surface area and activity.
Synthesis and optimisation of ir o2 electrocatalysts by adams fusion method f...sudesh789
This document discusses the synthesis and optimization of iridium dioxide (IrO2) electrocatalysts for use in solid polymer electrolyte electrolyzers through an adaptation of the Adams fusion method. The synthesis duration and temperature were varied to determine their effect on the physical and electrochemical properties of the IrO2 catalysts. X-ray diffraction analysis showed that increasing the synthesis duration and temperature increased the crystallinity and particle size of the IrO2. Chronoamperometry testing revealed that a synthesis of 2 hours at 350°C produced an IrO2 catalyst with better electrocatalytic activity for oxygen evolution than a commercial IrO2 catalyst.
IrO2 as an anodic electrocatalyst for the oxygen evolution reaction (OER) in solid polymer electrolyte (SPE)
electrolysers was synthesised by adapting the Adams fusion method. Optimisation of the IrO2 electrocatalyst was achieved
by varying the synthesis duration (0.5 – 4 hours) and temperature (250 - 500°C). The physical properties of the
electrocatalysts were characterised by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and
x-ray diffraction (XRD). Electrochemical characterisation of the electrocatalysts toward the OER was evaluated by
chronoamperometry (CA). CA analysis revealed the best electrocatalytic activity towards the OER for IrO2 synthesised
for 2 hours at 350oC which displayed a better electrocatalytic activity than the commercial IrO2 electrocatalyst used in this
study. XRD and TEM analyses revealed an increase in crystallinity and average particle size with increasing synthesis
duration and temperature which accounted for the decreasing electrocatalytic activity. At 250°C the formation of an active
IrO2 electrocatalyst was not favoured.
N-doped graphene quantum dots (NGQDs) catalyze the efficient electrochemical reduction of carbon dioxide into multi-carbon hydrocarbons and oxygenates such as ethylene, ethanol, and n-propanol. The NGQDs achieve high total faradaic efficiencies of up to 90% for carbon dioxide reduction, with selectivities for ethylene and ethanol conversions reaching 45%. Control experiments confirm the NGQDs are responsible for catalyzing the reaction. Compared to undoped graphene quantum dots, the NGQDs have higher activity and selectivity for producing valuable fuel and chemical products from carbon dioxide due to the presence of pyridinic nitrogen defects introduced during synthesis.
This document summarizes research on using various catalysts to promote the dehydrogenation of cyclohexane to produce hydrogen gas. Key findings include:
- Monometallic silver (Ag) catalysts supported on activated carbon cloth showed increasing hydrogen evolution rates with increasing Ag loading up to 10 wt%, but rates decreased at 15 wt% loading likely due to poorer dispersion.
- Bimetallic catalysts with 1 wt% noble metals (platinum, palladium, rhodium) promoted on 10 wt% Ag/ACC showed enhanced hydrogen evolution rates compared to the monometallic Ag catalyst. In particular, a 10 wt% Ag-1 wt% Pt catalyst produced hydrogen at twice the rate of the 10 wt%
This document describes a hydrometallurgical process for recovering rare earth elements from spent nickel-metal hydride batteries. The process involves three steps:
1) Leaching electrode materials from the batteries in sulfuric acid solutions using ozone as the oxidant, which achieved over 90% recovery of lanthanum, cerium, and neodymium.
2) Separating cobalt and part of the nickel from the leach solution using electrodeposition in an electrochemical reactor.
3) Precipitating the remaining rare earth elements along with the rest of the nickel by adjusting the pH of the solution.
Carbon-cuprous oxide composite nanoparticles
were chemically deposited on surface of thin glass tubes of spent
energy saving lamps for solar heat collection. Carbon was
obtained from fly ash of heavy oil incomplete combustion in
electric power stations. Impurities in the carbon were removed by
leaching with mineral acids. The mineral free-carbon was then
wet ground to have a submicron size. After filtration, it was
reacted with concentrated sulfuric/fuming nitric acid mixture on
cold for 3-4 days. Potassium chlorate was then added drop wise on
hot conditions to a carbon slurry followed by filtration.
Nanocarbon sample was mixed with 5% by weight PVA to help
adhesion to the glass surface. Carbon so deposited was doped with
copper nitrate solution. After dryness, the carbon/copper nitrate
film was dipped in hydrazine hydrate to form cuprous oxide -
carbon composite, It was then roasted at 380-400 °C A heat
collector testing assembly was constructed of 5 glass coils
connected in series with a total surface area of 1250 cm2
. Heat
collection was estimated by water flowing in the glass coils that
are coated with the carbon/copper film,. Parameters affecting the
solar collection efficiency such as time of exposure and mass flow
rate of the water were studied. Results revealed that the prepared
glass coil has proven successful energy collector for solar heat.
Synthesis of flower-like magnetite nanoassembly: Application in the efficient...Pawan Kumar
A facile approach for the synthesis of magnetite microspheres with flower-like morphology is reported
that proceeds via the reduction of iron(III) oxide under a hydrogen atmosphere. The ensuing magnetic
catalyst is well characterized by XRD, FE-SEM, TEM, N2 adsorption-desorption isotherm, and
Mössbauer spectroscopy and explored for a simple yet efficient transfer hydrogenation reduction of a
variety of nitroarenes to respective anilines in good to excellent yields (up to 98%) employing hydrazine
hydrate. The catalyst could be easily separated at the end of a reaction using an external magnet and
can be recycled up to 10 times without any loss in catalytic activity.
Effects of Precipitation pH Values on the Electrochemical Properties of β-Nic...iosrjce
IOSR Journal of Applied Chemistry (IOSR-JAC) is a double blind peer reviewed International Journal that provides rapid publication (within a month) of articles in all areas of applied chemistry and its applications. The journal welcomes publications of high quality papers on theoretical developments and practical applications in Chemical Science. Original research papers, state-of-the-art reviews, and high quality technical notes are invited for publications.
Maiyalagan, Synthesis and electro catalytic activity of methanol oxidation on...kutty79
Template synthesis of various nitrogen containing carbon nanotubes using different nitrogen containing polymers and the variation of nitrogen
content in carbon nanotube (CNT) on the behaviour of supported Pt electrodes in the anodic oxidation of methanol in direct methanol fuel cells was
investigated. Characterizations of the as-prepared catalysts are investigated by electron microscopy and electrochemical analysis. The catalyst with
N-containing CNT as a support exhibits a higher catalytic activity than that carbon supported platinum electrode and CNT supported electrodes.
The N-containing CNT supported electrodes with 10.5% nitrogen content show a higher catalytic activity compared to other N-CNT supported
electrodes. This could be due to the existence of additional active sites on the surface of the N-containing CNT supported electrodes, which favours
better dispersion of Pt particles. Also, the strong metal-support interaction plays a major role in enhancing the catalytic activity for methanol
oxidation.
This summarizes a document describing research on using boron-doped diamond (BDD) electrochemical reactors to treat polluted waters. Key points:
1) BDD electrodes have been used in various bench-scale electrochemical reactors, including undivided flow cells and trickle tower reactors, to degrade organic pollutants via electrochemical oxidation.
2) The BDD surface generates reactive oxygen species like hydroxyl radicals that can fully mineralize organic contaminants into CO2 and water. Operating parameters like current density and flow rate influence degradation rates.
3) Studies show these BDD reactors can achieve high removals of chemical oxygen demand (COD) and total organic carbon (TOC) for
Theoretical study of two dimensional Nano sheet for gas sensing applicationvivatechijri
This study is focus on various two dimensional material for sensing various gases with theoretical
view for new research in gas sensing application. In this paper we review various two dimensional sheet such as
Graphene, Boron Nitride nanosheet, Mxene and their application in sensing various gases present in the
atmosphere.
This document summarizes the synthesis, characterization, and evaluation of various IrO2-based binary metal oxide electrocatalysts for the oxygen evolution reaction. IrO2, IrxRu1-xO2, IrxSnx-1O2 and IrxTax-1O2 (where x is between 1 and 0.7) were synthesized via an adapted Adams fusion method. X-ray diffraction and electron microscopy showed the materials formed nanocrystalline solid solutions. Electrochemical testing found that adding RuO2, SnO2, or Ta2O5 to IrO2 improved its catalytic performance for oxygen evolution. Specifically, Ir0.7Ru0.3O2 exhibited the best
Recent progress on reduced graphene oxide....suresh kannan
The document summarizes recent progress on using reduced graphene oxide (rGO)-based materials as counter electrodes for dye-sensitized solar cells (DSSCs) as a cost-effective alternative to platinum. It discusses how rGO on its own is not effective as a counter electrode but that adding metal nanoparticles to rGO composites improves their catalytic activity and performance in DSSCs. The document reviews various rGO composites that have been studied, including those with silver, nickel, tungsten and platinum nanoparticles, as well as metal oxides and dichalcogenides. It compares the photovoltaic parameters of DSSCs using these rGO composite counter electrodes to those using conventional platinum counter electrodes
Similar to Cobalt-entrenched N-, O-, and S-tridoped carbons as efficient multifunctional sustainable catalysts for base-free selective oxidative esterification of alcohols
Reduced graphene oxide–CuO nanocomposites for photocatalyticconversion of CO2...Pawan Kumar
Reduced graphene oxide (rGO)–copper oxide nanocomposites are prepared by covalent grafting of CuOnanorods on the rGO skeleton. Chemical and structural features of rGO–CuO nanocomposites are probedby FTIR, XPS, XRD and HRTEM analyses. Photocatalytic potential of rGO–CuO nanocomposites is exploredfor reduction of CO2into the methanol under the visible light irradiation. The breadth of CuO nanorods andthe oxidation state of Cu in the rGO–CuO/Cu2O nanocomposites are systematically varied to investigatetheir photocatalytic activities. The pristine CuO nanorods exhibited very low photocatalytic activity owingto fast recombination of charge carriers and yielded 175 mol g−1methanol, whereas rGO–Cu2O andrGO–CuO exhibited significantly improved photocatalytic activities and yielded five (862 mol g−1) andseven (1228 mol g−1) folds methanol, respectively. The superior photocatalytic activity of CuO in therGO–CuO nanocomposites was attributed to slow recombination of charge carriers and efficient transferof photo-generated electrons through the rGO skeleton. This study further excludes the use of scavengingdonor.
Reduced graphene oxide–CuO nanocomposites for photocatalyticconversion of CO2...Pawan Kumar
tReduced graphene oxide (rGO)–copper oxide nanocomposites are prepared by covalent grafting of CuOnanorods on the rGO skeleton. Chemical and structural features of rGO–CuO nanocomposites are probedby FTIR, XPS, XRD and HRTEM analyses. Photocatalytic potential of rGO–CuO nanocomposites is exploredfor reduction of CO2into the methanol under the visible light irradiation. The breadth of CuO nanorods andthe oxidation state of Cu in the rGO–CuO/Cu2O nanocomposites are systematically varied to investigatetheir photocatalytic activities. The pristine CuO nanorods exhibited very low photocatalytic activity owingto fast recombination of charge carriers and yielded 175 mol g−1methanol, whereas rGO–Cu2O andrGO–CuO exhibited significantly improved photocatalytic activities and yielded five (862 mol g−1) andseven (1228 mol g−1) folds methanol, respectively. The superior photocatalytic activity of CuO in therGO–CuO nanocomposites was attributed to slow recombination of charge carriers and efficient transferof photo-generated electrons through the rGO skeleton. This study further excludes the use of scavengingdonor.
Performance of carbon nanofiber supported pd–ni catalysts for electro oxidati...suresh899
Carbon nanofibers (CNF) supported Pd–Ni nanoparticles have been prepared by chemical reduction
with NaBH4 as a reducing agent. The Pd–Ni/CNF catalysts were characterized by X-ray diffraction
(XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electrochemical
voltammetry analysis. TEM showed that the Pd–Ni particles were quite uniformly distributed on the
surface of the carbon nanofiber with an average particle size of 4.0 nm. The electro-catalytic activity of
the Pd–Ni/CNF for oxidation of ethanol was examined by cyclic voltammetry (CV). The onset potential
was 200mV lower and the peak current density four times higher for ethanol oxidation for Pd–Ni/CNF
compared to that for Pd/C. The effect of an increase in temperature from 20 to 60 ◦C had a great effect on
increasing the ethanol oxidation activity.
Performance of carbon nanofiber supported pd ni catalysts for electro-oxidati...Science Padayatchi
This document summarizes a study on carbon nanofiber (CNF) supported Pd-Ni catalysts for electro-oxidation of ethanol in alkaline medium. Pd-Ni/CNF catalysts were prepared by chemical reduction and characterized using various techniques. Electrochemical analysis showed the Pd-Ni/CNF catalyst had lower onset potential and 4 times higher peak current density for ethanol oxidation compared to Pd/C. Increasing the temperature from 20 to 60°C greatly enhanced the ethanol oxidation activity of Pd-Ni/CNF.
Performance of carbon nanofiber supported pd–ni catalysts for electro oxidati...sunilove
Carbon nanofibers (CNF) supported Pd–Ni nanoparticles have been prepared by chemical reduction
with NaBH4 as a reducing agent. The Pd–Ni/CNF catalysts were characterized by X-ray diffraction
(XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electrochemical
voltammetry analysis. TEM showed that the Pd–Ni particles were quite uniformly distributed on the
surface of the carbon nanofiber with an average particle size of 4.0 nm. The electro-catalytic activity of
the Pd–Ni/CNF for oxidation of ethanol was examined by cyclic voltammetry (CV). The onset potential
was 200mV lower and the peak current density four times higher for ethanol oxidation for Pd–Ni/CNF
compared to that for Pd/C. The effect of an increase in temperature from 20 to 60 ◦C had a great effect on
increasing the ethanol oxidation activity.
Synthesis and electro catalytic activity of methanol oxidation on nitrogen co...Science Padayatchi
The document discusses the synthesis and electro-catalytic activity of methanol oxidation on nitrogen containing carbon nanotubes supported Pt electrodes. Specifically:
1. Various nitrogen containing carbon nanotubes were synthesized using different nitrogen containing polymers as templates.
2. The nitrogen content and morphology of the carbon nanotubes were characterized using electron microscopy.
3. The catalytic activity of Pt supported on nitrogen containing carbon nanotubes was evaluated for methanol oxidation and compared to Pt supported on regular carbon nanotubes and carbon black.
4. Preliminary results showed that nitrogen containing carbon nanotubes with 10.5% nitrogen content exhibited higher catalytic activity than other supports, likely due to additional active sites from nitrogen
Synthesis and electro catalytic activity of methanol oxidation on nitrogen co...Science Padayatchi
The document discusses the synthesis and electro-catalytic activity of methanol oxidation on nitrogen containing carbon nanotubes supported Pt electrodes. Specifically:
1. Various nitrogen containing carbon nanotubes were synthesized using different nitrogen containing polymers as templates.
2. The nitrogen content and morphology of the carbon nanotubes were characterized using electron microscopy.
3. The electro-catalytic activity of Pt particles supported on nitrogen containing carbon nanotubes was evaluated for methanol oxidation and compared to conventional carbon supports. Nitrogen containing carbon nanotube supported electrodes showed higher catalytic activity.
Carbon based catalysts for oxygen reduction reaction (ORR) Lav Kumar Kasaudhan
The document discusses carbon-based catalysts for oxygen reduction reaction (ORR). It summarizes three journal papers on this topic. The first paper discusses the need for non-precious metal catalysts to replace platinum in fuel cells and issues with stability and durability. The second paper examines nitrogen and metal-containing catalysts and their activity. The third paper analyzes ORR activity on different fullerene molecules and active sites. Overall, the document reviews research gaps and findings on developing durable, non-precious metal catalysts for ORR.
This document summarizes research conducted at ISIS on energy materials. It discusses how neutron and x-ray techniques are used across multiple length scales to study materials related to energy production, storage and efficiency. Specific examples are given on the study of hydrogen storage alloys, carbon dioxide sequestration materials, and lithium ion battery electrode materials. The research aims to develop new environmentally friendly energy technologies through improved fundamental understanding of materials properties and structures.
One pot synthesis of chain-like palladium nanocubes and their enhanced electr...tshankar20134
This document describes a one-pot synthesis of chain-like palladium nanocubes and their enhanced electrocatalytic activity. A simple aqueous approach is used to produce anisotropic cubic chain-like Pd nanostructures using the neurotransmitter 5-hydroxytryptamine. Scanning electron microscopy images show the nanocubes have sizes between 140-210 nm and form chain-like branched structures. Testing shows the cubic chain-like nanostructures have over 11 times greater electrocatalytic activity for oxidizing formic acid, methanol, and ethanol compared to spherical nanoparticles and commercial Pd/C catalysts. The enhanced performance makes them promising multipurpose catalysts for direct fuel cells.
The document describes the development of a silver nanoparticle-modified poly ortho-toluidine/carbon paste electrode (n-Ag/POT/MCPE) and its application as an anode for the electrocatalytic oxidation of hydrazine in alkaline media. Scanning electron microscopy images show that the n-Ag/POT/MCPE has a porous surface topology suitable for catalyzing hydrazine oxidation. Cyclic voltammetry experiments demonstrate that the electrode exhibits high anodic and cathodic currents, indicating a large surface area, and is electrochemically active for hydrazine oxidation, with the oxidation current increasing with hydrazine concentration.
This document summarizes a study that developed a new hybrid electrocatalyst for oxygen evolution reaction (OER) by anchoring cobalt oxide (Co3O4) nanoparticles onto titanium carbide (Ti3C2) MXene nanosheets. The Co3O4/MXene hybrid (denoted CM) was synthesized using a solvothermal method. Characterization showed uniform distribution of small Co3O4 nanoparticles on MXene nanosheets. Electrochemical tests found the CM catalyst achieved overpotential of 300 mV at 10 mA/cm2 for OER, which was lower than Co3O4 or MXene alone. The enhanced performance was attributed to strong interactions and charge transfer between
Electrochemical study of anatase TiO2 in aqueous sodium-ion electrolytesRatnakaram Venkata Nadh
In this paper, a basic electro-analytical study on the behavior of anatase TiO2 in aqueous NaOH has been presented using cyclic voltammetry technique (CV). The study has explored the possibility of using TiO2 as anode material for ARSBs in presence of 5 M NaOH aqueous electrolyte. CV profiles show that anatase TiO2 exhibits reversible sodium ion insertion/de-insertion reactions. CV studies of TiO2 anode in aqueous sodium electrolytes at different scan rate shows that the Na+ ion insertion reaction at the electrode is diffusion controlled with a resistive behavior. Proton insertion from aqueous sodium electrolytes into TiO2 cannot be ruled out. To confirm the ion inserted and de-inserted, CV studies are done at different concentration of NaOH and it is found that at lower concentrations of NaOH, proton insertion process competes with Na+ ion insertion process and as the concentration increases, the Na+ ion insertion process becomes the predominant electrode reaction making it suitable anode materials for aqueous sodium batteries in 5 M NaOH.
The document discusses nanoparticles for small molecule electrocatalysis, specifically focusing on oxygen evolution reaction (OER) using Ni-Co hydroxides and oxides. It first provides background on OER and discusses how Co3O4, metal-doped Co3O4, and NiCo2O4 can be used as catalysts. It then outlines the purpose and scope of studying the composition dependence of Ni-Co hydroxides and oxides for OER using stainless steel mesh. The document reviews relevant theory around OER mechanisms and properties of different catalyst materials.
Nitrogen-Enriched Carbon Nanobubbles and Nanospheres for Applications in Ener...Devika Laishram
Multifunctional carbon nanomaterials have attracted remarkable consideration for use in various energy
conversion and storage devices because of their ultrahigh specific
surface area, unique morphology, and excellent electrochemical
properties. Herein, we report the synthesis of highly uniform and
ordered nitrogen-enriched carbon nanospheres (CS) and nanobubbles (CNB) by a modified Stöber reaction using resorcinol and
formaldehyde in the presence of ethylenediamine as a nitrogen
source. A comparative study of the prepared CS and CNB
nanomaterials is presented here with potential use in a wide variety
of applications involving large surface area and electrical
conductivity. As counter electrode materials in solar cells, CNB and CS showed enhanced photoelectrochemical activity for
catalytically reducing I3
− to I− and improved capacitive behavior with a low charge transfer resistance and remarkable power
conversion efficiency (PCE) of 10.40% with improved Jsc (20.20 mA/cm2
) and Voc (0.73 V). The enhanced performance of the
fabricated photoelectrochemical cell is due to the excellent point contact and good conductivity that offered better charge
transportation of electrons with minimum recombination. The enhanced adsorption upon increasing the pressure without an
apparent saturation level signified the large CO2 adsorption with 2 mmol/g for the CS. Additionally, the rectangular-shaped CV
curve indicated the double-layer capacitive behavior, good electrochemical reversibility, and high-power characteristics, prerequisites
for supercapacitor application. This study probes the practical possibility of nitrogen-enriched carbon nanostructures as a
multifunctional material for prospective applications.
This document summarizes research on using electrodeposited manganese dioxide (MnO2) coatings on porous carbon substrates for capacitive deionization (CDI) applications. Two carbon substrates with different surface areas and morphologies were coated with MnO2 using galvanostatic and cyclic voltammetric deposition. Characterization of the coated electrodes found mixed MnO2 phases present. Testing in half-cell configurations showed that maximum ion uptake per mass was not necessarily optimal for practical CDI applications, where performance per electrode area is more important. The results suggest the structure and deposition method can impact how effectively the electrode volume participates in ion removal reactions.
Bioinspired multimetal electrocatalyst for selective methane oxidationPawan Kumar
Selective partial electrooxidation of methane (CH4) to liquid oxygenates has been a long-sought goal. However, the high activation energy of C–H bonds and competing oxygen evolution reaction limit product selectivity and reaction rates. Inspired by iron (IV)-oxo containing metalloenzymes’ functionality to activate the C–H bond, here we report on the design of a copper-iron-nickel catalyst for selective oxidation of CH4 to formate via a peroxide-assisted pathway. Each catalyst serves a specific role which is confirmed via electrochemical, in situ, and theoretical studies. A combination of electrochemical and in situ spectroelectrochemical studies revealed that H2O2 oxidation on nickel led to the formation of active oxygen species which trigger the formation of iron (IV) at low voltages. Density functional theory analysis helped reveal the role of iron (IV)-oxo species in reducing the activation energy barrier for CH4 deprotonation and the critical role of copper to suppress overoxidation. Our multimetal catalyst exhibits a formate faradaic efficiency of 42% at an applied potential of 0.9 V versus a reversible hydrogen electrode.
Similar to Cobalt-entrenched N-, O-, and S-tridoped carbons as efficient multifunctional sustainable catalysts for base-free selective oxidative esterification of alcohols (20)
Isolated Iridium Sites on Potassium-Doped Carbon-nitride wrapped Tellurium Na...Pawan Kumar
Many industrial processes such transesterification of fatty acid for biodiesel production, soap manufacturing and biosynthesis of ethanol generate glycerol as a major by-product that can be used to produce commodity chemicals. Photocatalytic transformation of glycerol is an enticing approach that can exclude the need of harsh oxidants and extraneous thermal energy. However, the product yield and selectivity remain poor due to low absorption and unsymmetrical site distribution on the catalyst surface. Herein, tellurium (Te) nanorods/nanosheets (TeNRs/NSs) wrapped potassium-doped carbon nitride (KCN) van der Waal (vdW) heterojunction (TeKCN) is designed to enhance charge separation and visible-NIR absorption. The iridium (Ir) single atom sites decoration on the TeKCN core-shell structure (TeKCNIr) promotes selective oxidation of glycerol to glyceraldehyde with a conversion of 45.6% and selectivity of 61.6% under AM1.5G irradiation. The catalytic selectivity can reach up to 88% under 450 nm monochromatic light. X-ray absorption spectroscopy (XAS) demonstrates the presence of undercoordinated IrN2O2 sites which improved catalytic selectivity for glycol oxidation. Band energies and computational calculations reveal faile charge transfer in the TeKCNIr heterostructure. EPR and scavenger tests discern that superoxide (O2•−) and hydroxyl (•OH) radicals are prime components driving glycerol oxidation.
Isolated Iridium Sites on Potassium-Doped Carbon-nitride wrapped Tellurium Na...Pawan Kumar
Many industrial processes such transesterification of fatty acid for biodiesel production, soap manufacturing and biosynthesis of ethanol generate glycerol as a major by-product that can be used to produce commodity chemicals. Photocatalytic transformation of glycerol is an enticing approach that can exclude the need of harsh oxidants and extraneous thermal energy. However, the product yield and selectivity remain poor due to low absorption and unsymmetrical site distribution on the catalyst surface. Herein, tellurium (Te) nanorods/nanosheets (TeNRs/NSs) wrapped potassium-doped carbon nitride (KCN) van der Waal (vdW) heterojunction (TeKCN) is designed to enhance charge separation and visible-NIR absorption. The iridium (Ir) single atom sites decoration on the TeKCN core-shell structure (TeKCNIr) promotes selective oxidation of glycerol to glyceraldehyde with a conversion of 45.6% and selectivity of 61.6% under AM1.5G irradiation. The catalytic selectivity can reach up to 88% under 450 nm monochromatic light. X-ray absorption spectroscopy (XAS) demonstrates the presence of undercoordinated IrN2O2 sites which improved catalytic selectivity for glycol oxidation. Band energies and computational calculations reveal faile charge transfer in the TeKCNIr heterostructure. EPR and scavenger tests discern that superoxide (O2•−) and hydroxyl (•OH) radicals are prime components driving glycerol oxidation.
Isolated Iridium Sites on Potassium-Doped Carbon-nitride wrapped Tellurium Na...Pawan Kumar
Many industrial processes such transesterification of fatty acid for biodiesel production, soap manufacturing and biosynthesis of ethanol generate glycerol as a major by-product that can be used to produce commodity chemicals. Photocatalytic transformation of glycerol is an enticing approach that can exclude the need of harsh oxidants and extraneous thermal energy. However, the product yield and selectivity remain poor due to low absorption and unsymmetrical site distribution on the catalyst surface. Herein, tellurium (Te) nanorods/nanosheets (TeNRs/NSs) wrapped potassium-doped carbon nitride (KCN) van der Waal (vdW) heterojunction (TeKCN) is designed to enhance charge separation and visible-NIR absorption. The iridium (Ir) single atom sites decoration on the TeKCN core-shell structure (TeKCNIr) promotes selective oxidation of glycerol to glyceraldehyde with a conversion of 45.6% and selectivity of 61.6% under AM1.5G irradiation. The catalytic selectivity can reach up to 88% under 450 nm monochromatic light. X-ray absorption spectroscopy (XAS) demonstrates the presence of undercoordinated IrN2O2 sites which improved catalytic selectivity for glycol oxidation. Band energies and computational calculations reveal faile charge transfer in the TeKCNIr heterostructure. EPR and scavenger tests discern that superoxide (O2•−) and hydroxyl (•OH) radicals are prime components driving glycerol oxidation.
Solar-Driven Cellulose Photorefining into Arabinose over Oxygen-Doped Carbon ...Pawan Kumar
Biomass photorefining is a promising strategy to address the energy crisis and transition toward carbon carbon-neutral society. Here, we demonstrate the feasibility of direct cellulose photorefining into arabinose by a rationally designed oxygen-doped polymeric carbon nitride, which generates favorable oxidative species (e.g., O2–, •OH) for selective oxidative reactions at neutral conditions. In addition, we also illustrate the mechanism of the photocatalytic cellulose to arabinose conversion by density functional theory calculations. The oxygen insertion derived from oxidative radicals at the C1 position of glucose within cellulose leads to oxidative cleavage of β-1,4 glycosidic linkages, resulting in the subsequent gluconic acid formation. The following decarboxylation process of gluconic acid via C1–C2 α-scissions, triggered by surface oxygen-doped active sites, generates arabinose and formic acid, respectively. This work not only offers a mechanistic understanding of cellulose photorefining to arabinose but also sets up an example for illuminating the path toward direct cellulose photorefining into value-added bioproducts under mild conditions.
Solar-Driven Cellulose Photorefining into Arabinose over Oxygen-Doped Carbon ...Pawan Kumar
Biomass photorefining is a promising strategy to address the energy crisis and transition toward carbon carbon-neutral society. Here, we demonstrate the feasibility of direct cellulose photorefining into arabinose by a rationally designed oxygen-doped polymeric carbon nitride, which generates favorable oxidative species (e.g., O2–, •OH) for selective oxidative reactions at neutral conditions. In addition, we also illustrate the mechanism of the photocatalytic cellulose to arabinose conversion by density functional theory calculations. The oxygen insertion derived from oxidative radicals at the C1 position of glucose within cellulose leads to oxidative cleavage of β-1,4 glycosidic linkages, resulting in the subsequent gluconic acid formation. The following decarboxylation process of gluconic acid via C1–C2 α-scissions, triggered by surface oxygen-doped active sites, generates arabinose and formic acid, respectively. This work not only offers a mechanistic understanding of cellulose photorefining to arabinose but also sets up an example for illuminating the path toward direct cellulose photorefining into value-added bioproducts under mild conditions.
Solar-Driven Cellulose Photorefining into Arabinose over Oxygen-Doped Carbon ...Pawan Kumar
Biomass photorefining is a promising strategy to address the energy crisis and transition toward carbon carbon-neutral society. Here, we demonstrate the feasibility of direct cellulose photorefining into arabinose by a rationally designed oxygen-doped polymeric carbon nitride, which generates favorable oxidative species (e.g., O2–, •OH) for selective oxidative reactions at neutral conditions. In addition, we also illustrate the mechanism of the photocatalytic cellulose to arabinose conversion by density functional theory calculations. The oxygen insertion derived from oxidative radicals at the C1 position of glucose within cellulose leads to oxidative cleavage of β-1,4 glycosidic linkages, resulting in the subsequent gluconic acid formation. The following decarboxylation process of gluconic acid via C1–C2 α-scissions, triggered by surface oxygen-doped active sites, generates arabinose and formic acid, respectively. This work not only offers a mechanistic understanding of cellulose photorefining to arabinose but also sets up an example for illuminating the path toward direct cellulose photorefining into value-added bioproducts under mild conditions.
Partial Thermal Condensation Mediated Synthesis of High-Density Nickel Single...Pawan Kumar
Direct selective transformation of greenhouse methane (CH4) to liquid oxygenates (methanol) can substitute energy-intensive two-step (reforming/Fischer–Tropsch) synthesis while creating environmental benefits. The development of inexpensive, selective, and robust catalysts that enable room temperature conversion will decide the future of this technology. Single-atom catalysts (SACs) with isolated active centers embedded in support have displayed significant promises in catalysis to drive challenging reactions. Herein, high-density Ni single atoms are developed and stabilized on carbon nitride (NiCN) via thermal condensation of preorganized Ni-coordinated melem units. The physicochemical characterization of NiCN with various analytical techniques including HAADF-STEM and X-ray absorption fine structure (XAFS) validate the successful formation of Ni single atoms coordinated to the heptazine-constituted CN network. The presence of uniform catalytic sites improved visible absorption and carrier separation in densely populated NiCN SAC resulting in 100% selective photoconversion of (CH4) to methanol using H2O2 as an oxidant. The superior catalytic activity can be attributed to the generation of high oxidation (NiIII═O) sites and selective C─H bond cleavage to generate •CH3 radicals on Ni centers, which can combine with •OH radicals to generate CH3OH.
Partial Thermal Condensation Mediated Synthesis of High-Density Nickel Single...Pawan Kumar
Direct selective transformation of greenhouse methane (CH4) to liquid oxygenates (methanol) can substitute energy-intensive two-step (reforming/Fischer–Tropsch) synthesis while creating environmental benefits. The development of inexpensive, selective, and robust catalysts that enable room temperature conversion will decide the future of this technology. Single-atom catalysts (SACs) with isolated active centers embedded in support have displayed significant promises in catalysis to drive challenging reactions. Herein, high-density Ni single atoms are developed and stabilized on carbon nitride (NiCN) via thermal condensation of preorganized Ni-coordinated melem units. The physicochemical characterization of NiCN with various analytical techniques including HAADF-STEM and X-ray absorption fine structure (XAFS) validate the successful formation of Ni single atoms coordinated to the heptazine-constituted CN network. The presence of uniform catalytic sites improved visible absorption and carrier separation in densely populated NiCN SAC resulting in 100% selective photoconversion of (CH4) to methanol using H2O2 as an oxidant. The superior catalytic activity can be attributed to the generation of high oxidation (NiIII═O) sites and selective C─H bond cleavage to generate •CH3 radicals on Ni centers, which can combine with •OH radicals to generate CH3OH.
Selective Cellobiose Photoreforming for Simultaneous Gluconic Acid and Syngas...Pawan Kumar
Here, we demonstrate the selective cellobiose (building block of cellulose) photoreforming for gluconic acid and syngas co-production in acidic conditions by rationally designing a bifunctional polymeric carbon nitride (CN) with potassium/sulfur co-dopant. This heteroatomic doped CN photocatalyst possesses enhanced visible light absorption, higher charge separation efficiency than pristine CN. Under acidic conditions, cellobiose is not only more efficiently hydrolyzed into glucose but also promotes the syngas and gluconic acid production. Density functional theory (DFT) calculations reveal the favorable generation of •O2− during the photocatalytic reaction, which is essential for gluconic acid production. Consequently, the fine-designed photocatalyst presents excellent cellobiose conversion (>80%) and gluconic acid selectivity (>70%) together with the co-production of syngas (~56 μmol g-1 h-1) under light illumination. The current work demonstrates the feasibility of biomass photoreforming with value-added chemicals and syngas co-production under mild condition.
Selective Cellobiose Photoreforming for Simultaneous Gluconic Acid and Syngas...Pawan Kumar
Here, we demonstrate the selective cellobiose (building block of cellulose) photoreforming for gluconic acid and syngas co-production in acidic conditions by rationally designing a bifunctional polymeric carbon nitride (CN) with potassium/sulfur co-dopant. This heteroatomic doped CN photocatalyst possesses enhanced visible light absorption, higher charge separation efficiency than pristine CN. Under acidic conditions, cellobiose is not only more efficiently hydrolyzed into glucose but also promotes the syngas and gluconic acid production. Density functional theory (DFT) calculations reveal the favorable generation of •O2− during the photocatalytic reaction, which is essential for gluconic acid production. Consequently, the fine-designed photocatalyst presents excellent cellobiose conversion (>80%) and gluconic acid selectivity (>70%) together with the co-production of syngas (~56 μmol g-1 h-1) under light illumination. The current work demonstrates the feasibility of biomass photoreforming with value-added chemicals and syngas co-production under mild condition.
Selective Cellobiose Photoreforming for Simultaneous Gluconic Acid and Syngas...Pawan Kumar
Here, we demonstrate the selective cellobiose (building block of cellulose) photoreforming for gluconic acid and syngas co-production in acidic conditions by rationally designing a bifunctional polymeric carbon nitride (CN) with potassium/sulfur co-dopant. This heteroatomic doped CN photocatalyst possesses enhanced visible light absorption, higher charge separation efficiency than pristine CN. Under acidic conditions, cellobiose is not only more efficiently hydrolyzed into glucose but also promotes the syngas and gluconic acid production. Density functional theory (DFT) calculations reveal the favorable generation of •O2− during the photocatalytic reaction, which is essential for gluconic acid production. Consequently, the fine-designed photocatalyst presents excellent cellobiose conversion (>80%) and gluconic acid selectivity (>70%) together with the co-production of syngas (~56 μmol g-1 h-1) under light illumination. The current work demonstrates the feasibility of biomass photoreforming with value-added chemicals and syngas co-production under mild condition.
Partial Thermal Condensation Mediated Synthesis of High-Density Nickel Single...Pawan Kumar
Direct selective transformation of greenhouse methane (CH4) to liquid oxygenates (methanol) can substitute energy-intensive two-step (reforming/Fischer–Tropsch) synthesis while creating environmental benefits. The development of inexpensive, selective, and robust catalysts that enable room temperature conversion will decide the future of this technology. Single-atom catalysts (SACs) with isolated active centers embedded in support have displayed significant promises in catalysis to drive challenging reactions. Herein, high-density Ni single atoms are developed and stabilized on carbon nitride (NiCN) via thermal condensation of preorganized Ni-coordinated melem units. The physicochemical characterization of NiCN with various analytical techniques including HAADF-STEM and X-ray absorption fine structure (XAFS) validate the successful formation of Ni single atoms coordinated to the heptazine-constituted CN network. The presence of uniform catalytic sites improved visible absorption and carrier separation in densely populated NiCN SAC resulting in 100% selective photoconversion of (CH4) to methanol using H2O2 as an oxidant. The superior catalytic activity can be attributed to the generation of high oxidation (NiIII═O) sites and selective C─H bond cleavage to generate •CH3 radicals on Ni centers, which can combine with •OH radicals to generate CH3OH.
Recent advancements in tuning the electronic structures of transitional metal...Pawan Kumar
The smooth transition from finite non-renewables to renewable energy conversion technologies will require efficient electrocatalysts which can harness intermittent energies to store in the form of chemical bonds. The oxygen evolution reaction (OER) impedes the widespread usage of water electrolyzers to convert H2O into H2 and persists as a bottleneck, including other energy conversion devices with sluggish four H+/e− kinetics. In this context, designing highly active and stable catalysts capable of driving a lower overpotential in the OER to produce continuous hydrogen (H2) is a primary demanded. This chapter discussed the mechanism of the OER in conventional adsorbate oxygen and lattice oxygen participation in transition metal oxides (TMOs). Further, the influences of surface engineering, doping, and defects in the TMOs and understanding the electronic structure to screen electrodes towards the structure–activity relationship are highlighted. Specifically, the adsorption strength of O 2p is understood in detail as its binding ability over the surface of TMOs can be correlated directly to the OER activity. The iterative development of TMOs in terms of understanding electronic structural attributes is essential for the commercial deployment of energy conversion technologies. The comprehensive outlook of this chapter investigates thoroughly how TMOs can be used as significant materials for the OER in the near future.
Hole transport materials (HTMs) have a significant impact on the effectiveness of organic electronic devices; therefore, we present a molecular architecture of pyrazino[2,3-g]quinoxaline (PQ10)-based room-temperature organic liquid crystalline semiconductor (OLCS) as an alternative HTM. The PQ10 compound exhibits three different rectangular columnar (Colr) phases offering an impressive hole mobility of 8.8 × 10−3 cm2V−1s−1 which is found to be dexterous than most of existing polymeric hole transport materials. The charge transport mechanism is governed by the hole polarons hopping through H-aggregates of the PQ10 molecules and the hole mobility remains nearly constant throughout the mesophase range, but it decreases with increasing applied electric field. The current-voltage characteristics of the PQ10 have also been investigated in all three Colr phases and explained via the Poole-Frenkel conduction mechanism. The dielectric spectroscopy has been eventually carried out to understand the nature of dielectric permittivity and conductivity as a function of temperature and a correlation is established between the molecular architecture of the Colr phases and aforementioned physical properties. Solar cell simulation has been additionally performed to demonstrate that the PQ10 material can be a better choice as HTM for organic electronics and photovoltaic applications.
Multifunctional carbon nitride nanoarchitectures for catalysisPawan Kumar
Catalysis is at the heart of modern-day chemical and pharmaceutical industries, and there is an urgent demand to develop metal-free, high surface area, and efficient catalysts in a scalable, reproducible and economic manner. Amongst the ever-expanding two-dimensional materials family, carbon nitride (CN) has emerged as the most researched material for catalytic applications due to its unique molecular structure with tunable visible range band gap, surface defects, basic sites, and nitrogen functionalities. These properties also endow it with anchoring capability with a large number of catalytically active sites and provide opportunities for doping, hybridization, sensitization, etc. To make considerable progress in the use of CN as a highly effective catalyst for various applications, it is critical to have an in-depth understanding of its synthesis, structure and surface sites. The present review provides an overview of the recent advances in synthetic approaches of CN, its physicochemical properties, and band gap engineering, with a focus on its exclusive usage in a variety of catalytic reactions, including hydrogen evolution reactions, overall water splitting, water oxidation, CO2 reduction, nitrogen reduction reactions, pollutant degradation, and organocatalysis. While the structural design and band gap engineering of catalysts are elaborated, the surface chemistry is dealt with in detail to demonstrate efficient catalytic performances. Burning challenges in catalytic design and future outlook are elucidated.
Production of Renewable Fuels by the Photocatalytic Reduction of CO2 using Ma...Pawan Kumar
The photo-reductive performance of natural ilmenite was boosted and the production of renewable fuels from the reduction of CO2 was enhanced by doping the natural mineral with magnesium. The doping was achieved by high energy ball milling in the presence of MgO and Mg(NO3)2. The photo-reduction of CO2 in aqueous solution led to the evolution of H2, CH4, C2H4, and C2H6, and the insertion of Mg in the structure of ilmenite enabled increases of up to 1245% in the fuel production yield, reaching total production of 210.9 µmol h-1 gcat-1. Displacements of the conduction band to more negative potentials were evidenced for the samples doped with magnesium. Indirect effects such as increases in the valence band maximum, and the introduction of intermediate energy levels were also evidenced through the measurement of the crystallite size and the determination of the band structure of the materials. Mott-Schottky analyses of the samples showed the n-type nature of the semiconductor materials and enabled the estimation of the density of charge carriers, which strongly influenced the photocatalytic performance. The strong potential of the application of natural ilmenite in gas phase artificial photosynthesis was proved by the evaluation of CO2 reduction in gas conditions, which allowed the enhancement in the selectivity and significantly increased the production of CH4 as compared to aqueous solution, reaching an important yield of CH4 of 16.1 µmol h-1 gcat-1.
Nanoengineered Au-Carbon Nitride Interfaces Enhance PhotoCatalytic Pure Water...Pawan Kumar
Photocatalytic pure water splitting using solar energy is one of the promising routes to produce sustainable green hydrogen (H2). Tuning the interfacial active site density at catalytic heterojunctions and better light management are imperative to steer the structure-activity correlations to enhance the photo-efficiency of nanocomposite photocatalysts. Herein, we report the decoration of nitrogen defects-rich carbon nitride CN(T) with metallic Au nanostructures of different morphologies and sizes to investigate their influence on the photocatalytic hydrogen evolution reactions (HER). The CN(T)-7-NP nano-heterostructure comprises Au nanoparticles (NPs) of ~7 nm and thiourea-derived defective CN exhibits an excellent H2 production rate of 76.8 µmol g–1 h–1 from pure water under simulated AM 1.5 solar irradiation. In contrast to large-size Au nanorods, the high activity of CN(T)-7-NP was attributed to their strong localized surface plasmon resonance (LSPR) mediated visible absorption and interfacial charge separation. The surface ligands used to control Au nanostructures morphology were found to play a major role in the stabilization of NPs and improve interfacial charge transport between Au NPs and CN(T). First-principles calculations revealed that defects in CN and Au-CN interfacial sites in these nanocomposites facilitate the separation of e-/h+ pairs after light excitation and provide lower energy barrier pathways for H2 production by photocatalytic water splitting.
Nanoengineered Au-Carbon Nitride Interfaces Enhance Photo-Catalytic Pure Wate...Pawan Kumar
Photocatalytic pure water splitting using solar energy is one of the promising routes to produce sustainable green hydrogen (H2). Tuning the interfacial active site density at catalytic heterojunctions and better light management are imperative to steer the structure-activity correlations to enhance the photo-efficiency of nanocomposite photocatalysts. Herein, we report the decoration of nitrogen defects-rich carbon nitride CN(T) with metallic Au nanostructures of different morphologies and sizes to investigate their influence on the photocatalytic hydrogen evolution reactions (HER). The CN(T)-7-NP nano-heterostructure comprises Au nanoparticles (NPs) of ~7 nm and thiourea-derived defective CN exhibits an excellent H2 production rate of 76.8 µmol g–1 h–1 from pure water under simulated AM 1.5 solar irradiation. In contrast to large-size Au nanorods, the high activity of CN(T)-7-NP was attributed to their strong localized surface plasmon resonance (LSPR) mediated visible absorption and interfacial charge separation. The surface ligands used to control Au nanostructures morphology were found to play a major role in the stabilization of NPs and improve interfacial charge transport between Au NPs and CN(T). First-principles calculations revealed that defects in CN and Au-CN interfacial sites in these nanocomposites facilitate the separation of e-/h+ pairs after light excitation and provide lower energy barrier pathways for H2 production by photocatalytic water splitting.
Cooperative Copper Single Atom Catalyst in Two-dimensional Carbon Nitride for...Pawan Kumar
This document summarizes a study that investigated copper single atom catalysts supported on two-dimensional carbon nitride materials for enhancing the electrochemical reduction of carbon dioxide to methane. Specifically, copper ions were incorporated into the nanoporous structures of poly(heptazine imide) and poly(triazine imide) using a room temperature ion exchange process. This allowed for high loading densities of isolated copper sites. The proximity of copper atoms within the nanopores was found to enable cooperative catalysis that boosted the selectivity and efficiency of the multi-electron conversion of CO2 to CH4. Density functional theory calculations helped explain how the copper-copper distance and coordination environment modulated the binding of reaction intermediates. Optimized copper loading in the
Radial Nano-Heterojunctions Consisting of CdS Nanorods Wrapped by 2D CN:PDI P...Pawan Kumar
Solar energy harvesting using semiconductor photocatalysis offers an enticing solution to two of the biggest societal challenges, energy scarcity and environmental pollution. After decades of effort, no photocatalyst exists which can simultaneously meet the demand for excellent absorption, high quantum efficiency and photochemical resilience/durability. While CdS is an excellent photocatalyst for hydrogen evolution, pollutant degradation and organic synthesis, photocorrosion of CdS leads to the deactivation of the catalyst. Surface passivation of CdS with 2D graphitic carbon nitrides (CN) such as g-C3N4 and C3N5 has been shown to mitigate the photocorrosion problem but the poor oxidizing power of photogenerated holes in CN limits the utility of this approach for photooxidation reactions. We report the synthesis of exfoliated 2D nanosheets of a modified carbon nitride constituted of tris-s-triazine (C6N7) linked pyromellitic dianhydride polydiimide (CN:PDI) with a deep oxidative highest occupied molecular orbital (HOMO) position, which ensures sufficient oxidizing power for photogenerated holes in CN. The heterojunction formed by the wrapping of mono-/few layered CN:PDI on CdS nanorods (CdS/CN:PDI) was determined to be an excellent photocatalyst for oxidation reactions including photoelectrochemical water splitting, dye decolorization and the photocatalytic conversion of benzyl alcohol to benzaldehyde. Extensive structural characterization using HR-TEM, Raman, XPS, etc., confirmed wrapping of few-layered CN:PDI on CdS nanorods. The increased photoactivity in CdS/CN:PDI catalyst was ascribed to facile electron transfer from CdS to CN:PDI in comparison to CdS/g-C3N4, leading to an increased electron density on the surface of the photocatalyst to drive chemical reactions.
Comparing Evolved Extractive Text Summary Scores of Bidirectional Encoder Rep...University of Maribor
Slides from:
11th International Conference on Electrical, Electronics and Computer Engineering (IcETRAN), Niš, 3-6 June 2024
Track: Artificial Intelligence
https://www.etran.rs/2024/en/home-english/
The debris of the ‘last major merger’ is dynamically youngSérgio Sacani
The Milky Way’s (MW) inner stellar halo contains an [Fe/H]-rich component with highly eccentric orbits, often referred to as the
‘last major merger.’ Hypotheses for the origin of this component include Gaia-Sausage/Enceladus (GSE), where the progenitor
collided with the MW proto-disc 8–11 Gyr ago, and the Virgo Radial Merger (VRM), where the progenitor collided with the
MW disc within the last 3 Gyr. These two scenarios make different predictions about observable structure in local phase space,
because the morphology of debris depends on how long it has had to phase mix. The recently identified phase-space folds in Gaia
DR3 have positive caustic velocities, making them fundamentally different than the phase-mixed chevrons found in simulations
at late times. Roughly 20 per cent of the stars in the prograde local stellar halo are associated with the observed caustics. Based
on a simple phase-mixing model, the observed number of caustics are consistent with a merger that occurred 1–2 Gyr ago.
We also compare the observed phase-space distribution to FIRE-2 Latte simulations of GSE-like mergers, using a quantitative
measurement of phase mixing (2D causticality). The observed local phase-space distribution best matches the simulated data
1–2 Gyr after collision, and certainly not later than 3 Gyr. This is further evidence that the progenitor of the ‘last major merger’
did not collide with the MW proto-disc at early times, as is thought for the GSE, but instead collided with the MW disc within
the last few Gyr, consistent with the body of work surrounding the VRM.
Or: Beyond linear.
Abstract: Equivariant neural networks are neural networks that incorporate symmetries. The nonlinear activation functions in these networks result in interesting nonlinear equivariant maps between simple representations, and motivate the key player of this talk: piecewise linear representation theory.
Disclaimer: No one is perfect, so please mind that there might be mistakes and typos.
dtubbenhauer@gmail.com
Corrected slides: dtubbenhauer.com/talks.html
Phenomics assisted breeding in crop improvementIshaGoswami9
As the population is increasing and will reach about 9 billion upto 2050. Also due to climate change, it is difficult to meet the food requirement of such a large population. Facing the challenges presented by resource shortages, climate
change, and increasing global population, crop yield and quality need to be improved in a sustainable way over the coming decades. Genetic improvement by breeding is the best way to increase crop productivity. With the rapid progression of functional
genomics, an increasing number of crop genomes have been sequenced and dozens of genes influencing key agronomic traits have been identified. However, current genome sequence information has not been adequately exploited for understanding
the complex characteristics of multiple gene, owing to a lack of crop phenotypic data. Efficient, automatic, and accurate technologies and platforms that can capture phenotypic data that can
be linked to genomics information for crop improvement at all growth stages have become as important as genotyping. Thus,
high-throughput phenotyping has become the major bottleneck restricting crop breeding. Plant phenomics has been defined as the high-throughput, accurate acquisition and analysis of multi-dimensional phenotypes
during crop growing stages at the organism level, including the cell, tissue, organ, individual plant, plot, and field levels. With the rapid development of novel sensors, imaging technology,
and analysis methods, numerous infrastructure platforms have been developed for phenotyping.
Nucleophilic Addition of carbonyl compounds.pptxSSR02
Nucleophilic addition is the most important reaction of carbonyls. Not just aldehydes and ketones, but also carboxylic acid derivatives in general.
Carbonyls undergo addition reactions with a large range of nucleophiles.
Comparing the relative basicity of the nucleophile and the product is extremely helpful in determining how reversible the addition reaction is. Reactions with Grignards and hydrides are irreversible. Reactions with weak bases like halides and carboxylates generally don’t happen.
Electronic effects (inductive effects, electron donation) have a large impact on reactivity.
Large groups adjacent to the carbonyl will slow the rate of reaction.
Neutral nucleophiles can also add to carbonyls, although their additions are generally slower and more reversible. Acid catalysis is sometimes employed to increase the rate of addition.
ESR spectroscopy in liquid food and beverages.pptxPRIYANKA PATEL
With increasing population, people need to rely on packaged food stuffs. Packaging of food materials requires the preservation of food. There are various methods for the treatment of food to preserve them and irradiation treatment of food is one of them. It is the most common and the most harmless method for the food preservation as it does not alter the necessary micronutrients of food materials. Although irradiated food doesn’t cause any harm to the human health but still the quality assessment of food is required to provide consumers with necessary information about the food. ESR spectroscopy is the most sophisticated way to investigate the quality of the food and the free radicals induced during the processing of the food. ESR spin trapping technique is useful for the detection of highly unstable radicals in the food. The antioxidant capability of liquid food and beverages in mainly performed by spin trapping technique.
When I was asked to give a companion lecture in support of ‘The Philosophy of Science’ (https://shorturl.at/4pUXz) I decided not to walk through the detail of the many methodologies in order of use. Instead, I chose to employ a long standing, and ongoing, scientific development as an exemplar. And so, I chose the ever evolving story of Thermodynamics as a scientific investigation at its best.
Conducted over a period of >200 years, Thermodynamics R&D, and application, benefitted from the highest levels of professionalism, collaboration, and technical thoroughness. New layers of application, methodology, and practice were made possible by the progressive advance of technology. In turn, this has seen measurement and modelling accuracy continually improved at a micro and macro level.
Perhaps most importantly, Thermodynamics rapidly became a primary tool in the advance of applied science/engineering/technology, spanning micro-tech, to aerospace and cosmology. I can think of no better a story to illustrate the breadth of scientific methodologies and applications at their best.
Deep Behavioral Phenotyping in Systems Neuroscience for Functional Atlasing a...Ana Luísa Pinho
Functional Magnetic Resonance Imaging (fMRI) provides means to characterize brain activations in response to behavior. However, cognitive neuroscience has been limited to group-level effects referring to the performance of specific tasks. To obtain the functional profile of elementary cognitive mechanisms, the combination of brain responses to many tasks is required. Yet, to date, both structural atlases and parcellation-based activations do not fully account for cognitive function and still present several limitations. Further, they do not adapt overall to individual characteristics. In this talk, I will give an account of deep-behavioral phenotyping strategies, namely data-driven methods in large task-fMRI datasets, to optimize functional brain-data collection and improve inference of effects-of-interest related to mental processes. Key to this approach is the employment of fast multi-functional paradigms rich on features that can be well parametrized and, consequently, facilitate the creation of psycho-physiological constructs to be modelled with imaging data. Particular emphasis will be given to music stimuli when studying high-order cognitive mechanisms, due to their ecological nature and quality to enable complex behavior compounded by discrete entities. I will also discuss how deep-behavioral phenotyping and individualized models applied to neuroimaging data can better account for the subject-specific organization of domain-general cognitive systems in the human brain. Finally, the accumulation of functional brain signatures brings the possibility to clarify relationships among tasks and create a univocal link between brain systems and mental functions through: (1) the development of ontologies proposing an organization of cognitive processes; and (2) brain-network taxonomies describing functional specialization. To this end, tools to improve commensurability in cognitive science are necessary, such as public repositories, ontology-based platforms and automated meta-analysis tools. I will thus discuss some brain-atlasing resources currently under development, and their applicability in cognitive as well as clinical neuroscience.
Travis Hills' Endeavors in Minnesota: Fostering Environmental and Economic Pr...Travis Hills MN
Travis Hills of Minnesota developed a method to convert waste into high-value dry fertilizer, significantly enriching soil quality. By providing farmers with a valuable resource derived from waste, Travis Hills helps enhance farm profitability while promoting environmental stewardship. Travis Hills' sustainable practices lead to cost savings and increased revenue for farmers by improving resource efficiency and reducing waste.
ANAMOLOUS SECONDARY GROWTH IN DICOT ROOTS.pptxRASHMI M G
Abnormal or anomalous secondary growth in plants. It defines secondary growth as an increase in plant girth due to vascular cambium or cork cambium. Anomalous secondary growth does not follow the normal pattern of a single vascular cambium producing xylem internally and phloem externally.
Cobalt-entrenched N-, O-, and S-tridoped carbons as efficient multifunctional sustainable catalysts for base-free selective oxidative esterification of alcohols