Stationary Phase and Mobile Phase Selection for Liquid Chromatography
The presentation focuses on how to choose the appropriate mode of separation, the correct column and highlights the importance of the correct mobile phase. This approach will be applied to a wide selection of compound types ranging from proteins, peptides, glycans to small pharmaceutical molecules and their metabolites. It will also look at specific application areas for monoclonal antibody analysis, namely: titer, aggregation, charge and oxidation variant. Platform methods for biologics characterization are also discussed.
GAS CHROMATOGRAPHY-MASS SPECTROSCOPY [GC-MS]Shikha Popali
THIS PRESENTATION GIVES A DETAIL ACCOUNT ON THE GC-MS WITH ITS INTRODUCTION, BASIC PRINCIPLE OF BOTH COMBINED AND INDIVIDUALLY WITH ITS INSTRUMENTATION, APPLICATION AND EXAMPLES, MAKES EASY TO COLLECT ALL THE DATA AT A PLACE ACCORDING TO THE M.PHARM SYLLABUS S PER PCI
HPLC is Analytical technique that is used for separating the mixture of substances,so there is a number of promising application of HPLC-UV here uv detector is used which record the absorbance
Interfaces in chromatography [LC-MS, GC-MS, HPTLC, LC, GC]Shikha Popali
THE INTERFACES OF CHROMATOGRAPHY INCLUDES THE CHROMATOGRAPHY CRITEREA WHERE THE DIFFERENT CHROMATOGRAPHY ARE EXPLAINED IN DETAIL WITH PRACTICAL EXAMPLES AND THEIR IMAGES.
Stationary Phase and Mobile Phase Selection for Liquid Chromatography
The presentation focuses on how to choose the appropriate mode of separation, the correct column and highlights the importance of the correct mobile phase. This approach will be applied to a wide selection of compound types ranging from proteins, peptides, glycans to small pharmaceutical molecules and their metabolites. It will also look at specific application areas for monoclonal antibody analysis, namely: titer, aggregation, charge and oxidation variant. Platform methods for biologics characterization are also discussed.
GAS CHROMATOGRAPHY-MASS SPECTROSCOPY [GC-MS]Shikha Popali
THIS PRESENTATION GIVES A DETAIL ACCOUNT ON THE GC-MS WITH ITS INTRODUCTION, BASIC PRINCIPLE OF BOTH COMBINED AND INDIVIDUALLY WITH ITS INSTRUMENTATION, APPLICATION AND EXAMPLES, MAKES EASY TO COLLECT ALL THE DATA AT A PLACE ACCORDING TO THE M.PHARM SYLLABUS S PER PCI
HPLC is Analytical technique that is used for separating the mixture of substances,so there is a number of promising application of HPLC-UV here uv detector is used which record the absorbance
Interfaces in chromatography [LC-MS, GC-MS, HPTLC, LC, GC]Shikha Popali
THE INTERFACES OF CHROMATOGRAPHY INCLUDES THE CHROMATOGRAPHY CRITEREA WHERE THE DIFFERENT CHROMATOGRAPHY ARE EXPLAINED IN DETAIL WITH PRACTICAL EXAMPLES AND THEIR IMAGES.
Key Learning Objectives:
• Identify emerging triple quadrupole Gas Chromatography-Mass Spectrometry/Mass Spectrometry (GC-MS/MS) technology designed to address increasing regulatory demands and requirements
• Explore potential time savings in sample prep, method development/transition, and data analysis
• Demonstrate how to optimize the GC-MS/MS workflow from sample prep to sample analysis to automated data analysis
Overview:
Regulatory lab requirements continue to drive detection limits lower with an ever increasing list of compounds to analyze. These requirements also demand greater precision at these lower limits. Triple quadrupole GC-MS/MS is a viable option for enhanced analysis and increased productivity with an emphasis on simplicity. We discuss emerging trends and technologies designed to ensure that laboratories are well-equipped to address these increased demands with minimal investment in training and method development. Find out how you can adopt triple quadrupole GC-MS/MS technology in your laboratory using existing methods and source parameters in most instances while requiring less sample prep and enjoying the benefits of automated data analysis for increased simplicity and productivity.
For more information: www.thermoscientific.com/tsq8000
an overview of lcms and gcms and its applications....
LC-MS:
It is the combination of liquid chromatography and the mass spectrometry.
* In LC-MS we are removing the detector from the column of LC and fitting the column to interface of MS.
* In the most of the cases the interface used in LC-MS are ionization source
INTERFACE
Apart from being an inlet system for the
MS, an LC–MS interface is also the coupling
of a detector (MS) to a chromatograph.
The choice of LC–MS interface strongly
influences the characteristics of the MS as
a detector for LC. Therefore, we should
keep in mind what characteristics are ideal
for an LC detector
1. Direct liquid introduction (DLI):
The DLI interface was developed in order to solve the problems with in-capillary evaporation in the capillary inlet.
In a DLI interface, the column effluent is nebulized by the disintegration into small droplets of a liquid jet formed at a small diaphragm After desolvation of the droplets in a desolvation chamber, the analytes can be analysed using solvent-mediated CI with the LC solvents as the reagent gas.
Advantages:
• No heat is applied to the interface and it is therefore able to deal with thermally labile materials better than the moving-belt interface.
• The interface contains no moving parts and is cheap and simple to construct and operate and is inherently more reliable than the moving-belt interface.
• Both positive- and negative-ion CI spectra can be generated and the interface provides molecular weight information, plus it can also be used for sensitive quantitative and semi-quantitative procedures.
Disadvantages:
• Involatile compounds are not usually ionized with good efficiency.
• The pinhole is prone to blockage and therefore the system must be kept completely free of solid materials.
• Only a small proportion of the flow from a conventional HPLC column is able to enter the source of the mass spectrometer and sensitivity is consequently low
2. Moving belt/wire:
In a moving-belt interface (MBI), the column effluent is deposited onto an endless moving belt from which the solvent is evaporated by means of gentle heating and efficiently exhausting the solvent vapours. After removal of the solvents, the analyte molecules are (thermally) desorbed from the belt into the ion source and mass analysed.
The MBI for LC.MS was used in a wide variety of applications, including the analysis of drugs and their metabolites, pesticides, steroids, alkaloids, polycyclic, aromatic hydrocarbons and others.
Advantages:
• The interface can be used with a wide range of HPLC conditions.
• The analyst does have some choice of the ionization method to be used; EI, CI and FAB are available, subject to certain limitations, and thus both molecular weight and structural information may be obtained from the analyte(s) under investigation.
HPLC stands for “High-performance liquid chromatography”(sometimes referred to as High-pressure liquid chromatography).
High performance liquid chromatography is a powerful tool in analysis, it yields high performance and high speed compared to traditional columns chromatography because of the forcibly pumped mobile phase.
It is used in biochemistry and analytical chemistry to identify, quantify and purify the individual components of a mixture.
Gas chromatography-mass spectrometry (GC MS) is an analytical method in which GC is coupled with MS to identify different substances within a test sample.
1. It is one of the type of Hyphenated technique.
2. It is a combination of gas chromatographic technique and spectroscopic technique.
3. It is having a high resolution capacity.
4. It is used has volatile and Non-volatile compounds.
5. It is used for qualitative and quantitative analysis.
Hyphenated Techniques - coupling of a separation technique and an on-line spectroscopic detection technology.
Advantages of hyphenated techniques;
1. Fast and accurate analysis.
2. Higher degree of automation.
3. Higher sample throughput.
4. Better reproducibility.
5. Reduction of contamination due to its closed system.
6. Separation and quantification achieved at same time.
• It is the combination of liquid chromatography and the mass spectrometry.
• Liquid chromatography-mass spectrometry (LC-MS) is an analytical chemistry
technique that combines the physical separation capabilities of liquid
chromatography with the mass analysis capabilities of mass spectrometry.
• The combination of these two powerful techniques gives the chemical analyst the
ability to analyze virtually any molecular species; including, thermally labile, non
volatile, and high molecular weight species.
Key Learning Objectives:
• Identify emerging triple quadrupole Gas Chromatography-Mass Spectrometry/Mass Spectrometry (GC-MS/MS) technology designed to address increasing regulatory demands and requirements
• Explore potential time savings in sample prep, method development/transition, and data analysis
• Demonstrate how to optimize the GC-MS/MS workflow from sample prep to sample analysis to automated data analysis
Overview:
Regulatory lab requirements continue to drive detection limits lower with an ever increasing list of compounds to analyze. These requirements also demand greater precision at these lower limits. Triple quadrupole GC-MS/MS is a viable option for enhanced analysis and increased productivity with an emphasis on simplicity. We discuss emerging trends and technologies designed to ensure that laboratories are well-equipped to address these increased demands with minimal investment in training and method development. Find out how you can adopt triple quadrupole GC-MS/MS technology in your laboratory using existing methods and source parameters in most instances while requiring less sample prep and enjoying the benefits of automated data analysis for increased simplicity and productivity.
For more information: www.thermoscientific.com/tsq8000
an overview of lcms and gcms and its applications....
LC-MS:
It is the combination of liquid chromatography and the mass spectrometry.
* In LC-MS we are removing the detector from the column of LC and fitting the column to interface of MS.
* In the most of the cases the interface used in LC-MS are ionization source
INTERFACE
Apart from being an inlet system for the
MS, an LC–MS interface is also the coupling
of a detector (MS) to a chromatograph.
The choice of LC–MS interface strongly
influences the characteristics of the MS as
a detector for LC. Therefore, we should
keep in mind what characteristics are ideal
for an LC detector
1. Direct liquid introduction (DLI):
The DLI interface was developed in order to solve the problems with in-capillary evaporation in the capillary inlet.
In a DLI interface, the column effluent is nebulized by the disintegration into small droplets of a liquid jet formed at a small diaphragm After desolvation of the droplets in a desolvation chamber, the analytes can be analysed using solvent-mediated CI with the LC solvents as the reagent gas.
Advantages:
• No heat is applied to the interface and it is therefore able to deal with thermally labile materials better than the moving-belt interface.
• The interface contains no moving parts and is cheap and simple to construct and operate and is inherently more reliable than the moving-belt interface.
• Both positive- and negative-ion CI spectra can be generated and the interface provides molecular weight information, plus it can also be used for sensitive quantitative and semi-quantitative procedures.
Disadvantages:
• Involatile compounds are not usually ionized with good efficiency.
• The pinhole is prone to blockage and therefore the system must be kept completely free of solid materials.
• Only a small proportion of the flow from a conventional HPLC column is able to enter the source of the mass spectrometer and sensitivity is consequently low
2. Moving belt/wire:
In a moving-belt interface (MBI), the column effluent is deposited onto an endless moving belt from which the solvent is evaporated by means of gentle heating and efficiently exhausting the solvent vapours. After removal of the solvents, the analyte molecules are (thermally) desorbed from the belt into the ion source and mass analysed.
The MBI for LC.MS was used in a wide variety of applications, including the analysis of drugs and their metabolites, pesticides, steroids, alkaloids, polycyclic, aromatic hydrocarbons and others.
Advantages:
• The interface can be used with a wide range of HPLC conditions.
• The analyst does have some choice of the ionization method to be used; EI, CI and FAB are available, subject to certain limitations, and thus both molecular weight and structural information may be obtained from the analyte(s) under investigation.
HPLC stands for “High-performance liquid chromatography”(sometimes referred to as High-pressure liquid chromatography).
High performance liquid chromatography is a powerful tool in analysis, it yields high performance and high speed compared to traditional columns chromatography because of the forcibly pumped mobile phase.
It is used in biochemistry and analytical chemistry to identify, quantify and purify the individual components of a mixture.
Gas chromatography-mass spectrometry (GC MS) is an analytical method in which GC is coupled with MS to identify different substances within a test sample.
1. It is one of the type of Hyphenated technique.
2. It is a combination of gas chromatographic technique and spectroscopic technique.
3. It is having a high resolution capacity.
4. It is used has volatile and Non-volatile compounds.
5. It is used for qualitative and quantitative analysis.
Hyphenated Techniques - coupling of a separation technique and an on-line spectroscopic detection technology.
Advantages of hyphenated techniques;
1. Fast and accurate analysis.
2. Higher degree of automation.
3. Higher sample throughput.
4. Better reproducibility.
5. Reduction of contamination due to its closed system.
6. Separation and quantification achieved at same time.
• It is the combination of liquid chromatography and the mass spectrometry.
• Liquid chromatography-mass spectrometry (LC-MS) is an analytical chemistry
technique that combines the physical separation capabilities of liquid
chromatography with the mass analysis capabilities of mass spectrometry.
• The combination of these two powerful techniques gives the chemical analyst the
ability to analyze virtually any molecular species; including, thermally labile, non
volatile, and high molecular weight species.
Laser Ablation Molecular Isotopic Spectrometry for rare isotopes of the light...Alexander Bolshakov
Laser ablation molecular isotopic spectrometry (LAMIS) involves measuring isotope-resolved molecular emission. Measurements of several key isotopes (hydrogen, boron, carbon, nitrogen, oxygen, and chlorine) in laser ablation plumes were demonstrated. Requirements for spectral resolution of the optical detection system could be significantly relaxed when the isotopic ratio was determined using chemometric regression models. Multiple applications of LAMIS are anticipated in the nuclear power industry, medical diagnostics and therapies, forensics, carbon sequestration, and agronomy studies.
Laser ablation - optical cavity isotopic spectrometer (LAOCIS) for Mars roversAlexander Bolshakov
Proceedings of SPIE, v. 8385, "Sensors and Systems for Space Applications V"; Baltimore, MD, 2012. ABSTRACT: A concept of a compact device for analyzing key isotopic composition in surface materials without sample preparation is presented. This design is based on an advanced modification of Laser Induced Breakdown Spectroscopy (LIBS). First, we developed Laser Ablation Molecular Isotopic Spectrometry (LAMIS) that involves measuring isotope-resolved molecular emission, which exhibits significantly larger isotopic spectral shifts than those in atomic transitions. Second, we used laser ablation to vaporize the sample materials into a plume in which absorption spectra can be measured using a tunable diode laser. The intrinsically high spectral resolution of the diode lasers facilitates measurements of isotopic ratios. The absorption sensitivity can be boosted using cavity enhanced spectroscopy. Temporal behavior of species in a laser ablation plasma from solid samples with various isotopic composition was studied. Detection of key isotopes associated with signs of life (carbon, nitrogen, hydrogen) as well as strontium and boron in laser ablation plume was demonstrated; boron isotopes were quantified. Isotope-resolved spectra of many other molecular species were simulated. The experimental results demonstrate sensitivity to 86 Sr, 87 Sr, and 88 Sr with spectrally resolved measurements for each of them. It is possible to measure strontium isotopes in rocks on Mars for radiogenic age determination. Requirements for spectral resolution of the optical measurement system can be significantly relaxed when the isotopic abundance ratio is determined using chemometric analysis of spectra.
Chromatography is an analytical method in which compounds are physically separated and measured.
The main purpose of chromatography is to separate and quantify the target sample.
The Chromatography technique used to separate a mixture of compounds in pharmaceutical sciences , analytical analytical Chemistry with the purpose of identifying, quantifying and purifying the individual components of the mixture.
Here are the lecture notes from the presentation titled 'ICP-OES/MS Analysis: Advancements, Limitations, and Future Applications in Soil and Water Research,' delivered to a group of researchers affiliated with the Soil & Water Department, Faculty of Agriculture, Hebrew University of Jerusalem (Seagram Center) in 2023. The aim was to explore advanced technologies in elemental analysis and their application to soil and water research. The Lecture Notes Brochure (22 pages) can serve as a concise guide to ICP-OES/MS for researchers and students, assisting them in selecting the appropriate technique for their projects
Medical Technology Tackles New Health Care Demand - Research Report - March 2...pchutichetpong
M Capital Group (“MCG”) predicts that with, against, despite, and even without the global pandemic, the medical technology (MedTech) industry shows signs of continuous healthy growth, driven by smaller, faster, and cheaper devices, growing demand for home-based applications, technological innovation, strategic acquisitions, investments, and SPAC listings. MCG predicts that this should reflects itself in annual growth of over 6%, well beyond 2028.
According to Chris Mouchabhani, Managing Partner at M Capital Group, “Despite all economic scenarios that one may consider, beyond overall economic shocks, medical technology should remain one of the most promising and robust sectors over the short to medium term and well beyond 2028.”
There is a movement towards home-based care for the elderly, next generation scanning and MRI devices, wearable technology, artificial intelligence incorporation, and online connectivity. Experts also see a focus on predictive, preventive, personalized, participatory, and precision medicine, with rising levels of integration of home care and technological innovation.
The average cost of treatment has been rising across the board, creating additional financial burdens to governments, healthcare providers and insurance companies. According to MCG, cost-per-inpatient-stay in the United States alone rose on average annually by over 13% between 2014 to 2021, leading MedTech to focus research efforts on optimized medical equipment at lower price points, whilst emphasizing portability and ease of use. Namely, 46% of the 1,008 medical technology companies in the 2021 MedTech Innovator (“MTI”) database are focusing on prevention, wellness, detection, or diagnosis, signaling a clear push for preventive care to also tackle costs.
In addition, there has also been a lasting impact on consumer and medical demand for home care, supported by the pandemic. Lockdowns, closure of care facilities, and healthcare systems subjected to capacity pressure, accelerated demand away from traditional inpatient care. Now, outpatient care solutions are driving industry production, with nearly 70% of recent diagnostics start-up companies producing products in areas such as ambulatory clinics, at-home care, and self-administered diagnostics.
CHAPTER 1 SEMESTER V PREVENTIVE-PEDIATRICS.pdfSachin Sharma
This content provides an overview of preventive pediatrics. It defines preventive pediatrics as preventing disease and promoting children's physical, mental, and social well-being to achieve positive health. It discusses antenatal, postnatal, and social preventive pediatrics. It also covers various child health programs like immunization, breastfeeding, ICDS, and the roles of organizations like WHO, UNICEF, and nurses in preventive pediatrics.
India Clinical Trials Market: Industry Size and Growth Trends [2030] Analyzed...Kumar Satyam
According to TechSci Research report, "India Clinical Trials Market- By Region, Competition, Forecast & Opportunities, 2030F," the India Clinical Trials Market was valued at USD 2.05 billion in 2024 and is projected to grow at a compound annual growth rate (CAGR) of 8.64% through 2030. The market is driven by a variety of factors, making India an attractive destination for pharmaceutical companies and researchers. India's vast and diverse patient population, cost-effective operational environment, and a large pool of skilled medical professionals contribute significantly to the market's growth. Additionally, increasing government support in streamlining regulations and the growing prevalence of lifestyle diseases further propel the clinical trials market.
Growing Prevalence of Lifestyle Diseases
The rising incidence of lifestyle diseases such as diabetes, cardiovascular diseases, and cancer is a major trend driving the clinical trials market in India. These conditions necessitate the development and testing of new treatment methods, creating a robust demand for clinical trials. The increasing burden of these diseases highlights the need for innovative therapies and underscores the importance of India as a key player in global clinical research.
Explore our infographic on 'Essential Metrics for Palliative Care Management' which highlights key performance indicators crucial for enhancing the quality and efficiency of palliative care services.
This visual guide breaks down important metrics across four categories: Patient-Centered Metrics, Care Efficiency Metrics, Quality of Life Metrics, and Staff Metrics. Each section is designed to help healthcare professionals monitor and improve care delivery for patients facing serious illnesses. Understand how to implement these metrics in your palliative care practices for better outcomes and higher satisfaction levels.
Global launch of the Healthy Ageing and Prevention Index 2nd wave – alongside...ILC- UK
The Healthy Ageing and Prevention Index is an online tool created by ILC that ranks countries on six metrics including, life span, health span, work span, income, environmental performance, and happiness. The Index helps us understand how well countries have adapted to longevity and inform decision makers on what must be done to maximise the economic benefits that comes with living well for longer.
Alongside the 77th World Health Assembly in Geneva on 28 May 2024, we launched the second version of our Index, allowing us to track progress and give new insights into what needs to be done to keep populations healthier for longer.
The speakers included:
Professor Orazio Schillaci, Minister of Health, Italy
Dr Hans Groth, Chairman of the Board, World Demographic & Ageing Forum
Professor Ilona Kickbusch, Founder and Chair, Global Health Centre, Geneva Graduate Institute and co-chair, World Health Summit Council
Dr Natasha Azzopardi Muscat, Director, Country Health Policies and Systems Division, World Health Organisation EURO
Dr Marta Lomazzi, Executive Manager, World Federation of Public Health Associations
Dr Shyam Bishen, Head, Centre for Health and Healthcare and Member of the Executive Committee, World Economic Forum
Dr Karin Tegmark Wisell, Director General, Public Health Agency of Sweden
Defecation
Normal defecation begins with movement in the left colon, moving stool toward the anus. When stool reaches the rectum, the distention causes relaxation of the internal sphincter and an awareness of the need to defecate. At the time of defecation, the external sphincter relaxes, and abdominal muscles contract, increasing intrarectal pressure and forcing the stool out
The Valsalva maneuver exerts pressure to expel faeces through a voluntary contraction of the abdominal muscles while maintaining forced expiration against a closed airway. Patients with cardiovascular disease, glaucoma, increased intracranial pressure, or a new surgical wound are at greater risk for cardiac dysrhythmias and elevated blood pressure with the Valsalva maneuver and need to avoid straining to pass the stool.
Normal defecation is painless, resulting in passage of soft, formed stool
CONSTIPATION
Constipation is a symptom, not a disease. Improper diet, reduced fluid intake, lack of exercise, and certain medications can cause constipation. For example, patients receiving opiates for pain after surgery often require a stool softener or laxative to prevent constipation. The signs of constipation include infrequent bowel movements (less than every 3 days), difficulty passing stools, excessive straining, inability to defecate at will, and hard feaces
IMPACTION
Fecal impaction results from unrelieved constipation. It is a collection of hardened feces wedged in the rectum that a person cannot expel. In cases of severe impaction the mass extends up into the sigmoid colon.
DIARRHEA
Diarrhea is an increase in the number of stools and the passage of liquid, unformed feces. It is associated with disorders affecting digestion, absorption, and secretion in the GI tract. Intestinal contents pass through the small and large intestine too quickly to allow for the usual absorption of fluid and nutrients. Irritation within the colon results in increased mucus secretion. As a result, feces become watery, and the patient is unable to control the urge to defecate. Normally an anal bag is safe and effective in long-term treatment of patients with fecal incontinence at home, in hospice, or in the hospital. Fecal incontinence is expensive and a potentially dangerous condition in terms of contamination and risk of skin ulceration
HEMORRHOIDS
Hemorrhoids are dilated, engorged veins in the lining of the rectum. They are either external or internal.
FLATULENCE
As gas accumulates in the lumen of the intestines, the bowel wall stretches and distends (flatulence). It is a common cause of abdominal fullness, pain, and cramping. Normally intestinal gas escapes through the mouth (belching) or the anus (passing of flatus)
FECAL INCONTINENCE
Fecal incontinence is the inability to control passage of feces and gas from the anus. Incontinence harms a patient’s body image
PREPARATION AND GIVING OF LAXATIVESACCORDING TO POTTER AND PERRY,
An enema is the instillation of a solution into the rectum and sig
the IUA Administrative Board and General Assembly meeting
Cat 1
1. In-Situ UV-Visible and Raman Spectroscopy for Gas-Liquid-Solid Systems
C. P. Stemmet, J. C. Schouten, and T. A. Nijhuis*
Laboratory of Chemical Reactor Engineering, Department of Chemical Engineering and Chemistry, EindhoVen
UniVersity of Technology, P.O. Box 513, 5600 MB EindhoVen, The Netherlands
This paper presents the use of UV-vis and Raman spectroscopy to measure the state of a solid in a multiphase
reactor. A slurry of particles and a packed bubble column were used. As this study is a proof of principle a
model for an active catalyst system, insoluble pH indicators deposited on the particles and on a solid foam
packing (used as the packing material in the packed bubble column) are used. This insoluble pH indicator
has different UV-vis and Raman spectra according to the liquid pH. The experimental results indicate that
for the slurry the spectra obtained from the moving particles can be used to characterize the state of the pH
indicator. Bubbles in the packed bubble column result in disturbances in the UV-vis and Raman spectra
collected from the pH indicator adsorbed to the solid surface and this interference is removed successfully
with a newly developed tolerance-and-averaging method.
Introduction
Approximately 85% of all chemical products (bulk and fine
chemicals) are produced using a heterogeneous catalyst to
increase the reaction rate and hence increase production capac-
ity.1
Most often the catalyst is deposited on a solid support to
aid its separation from the reaction products and examples of
such reactors include packed beds, fluidized beds, and slurry
reactors. Multiphase reactors, where gas and liquid reactants
are converted over a heterogeneous catalyst, have been used
widely in the chemical industry and examples of such reactors
are slurry bubble columns, trickle bed reactors, and packed
bubble columns. These multiphase reactors are used in a variety
of applications ranging from the production of pharmaceuticals
and hydrogenations and oxidations to produce bulk chemicals
(hydro-treating, desulphurization, oxidation of sulfur dioxide,
etc.).
In-situ spectroscopic techniques have been developed over
the years to provide much understanding into the mechanisms
of catalytic reactions. In-situ spectroscopic techniques using
spectroscopic probes have been applied to control gas-solid
reactors operating under reaction conditions based on the state
of the solid catalyst.2,3
The key advantage of control based on
spectroscopic information is that the actual catalytic site (catalyst
state) is being probed directly, rather than the end-of-pipe
response at the reactor exit. In multiphase flows an optical probe
has been used to evaluate the local volume fraction of each
phase in an oil-water-gas mixture,4
however, spectroscopic
techniques in characterizing catalysts operating in multiphase
reactors (gas-liquid-solid) have not been investigated. It is
the intention of this study to assess whether UV-vis and Raman
spectroscopy can be used to determine the state of a solid
catalyst in a multiphase reactor system. In a chemical reactor
changes to a catalyst are usually slow, as good catalyst stability
is very important for an industrial process. In this study we used
a model system of which the state can be easily be manipulated
which makes the model development more facile. Insoluble pH
indicators were adsorbed on solid surfaces in a slurry of particles
and in a packed bubble column. These adsorbed pH indicators
are used as a model system for the catalyst in a multiphase
reactor.
In-Situ Spectroscopy. Spectroscopic measurements (ex situ
or in situ) have been widely used in the development and
determination of the main parameters in the preparation affecting
the stability and the size of catalytically active sites and the
intrinsic reaction rate. These techniques include ultraviolet-visible
spectroscopy (UV-vis), infrared spectroscopy (IR), Raman
spectroscopy, X-ray absorption near edge spectroscopy (XANES),
and X-ray absorption fine structure (XAFS) spectroscopy. The
main techniques and their limitations in catalyst characterization
are given in the books edited by Weckhuysen,1
and Haw,5
as
well as the review papers by Weckhuysen,6
and Hunger and
Weitkamp.7
The use of in situ spectroscopy has seen significant
increase, largely due to the development of optical probes which
may be used under high temperature and high pressure reaction
conditions.
UV-vis and Raman spectroscopy can give quantitative
information regarding the oxidation state and co-ordination of
the metal oxide complexes serving as catalytically active species.
The main uses of oxides of transition metals are for a number
of chemical conversions such as hydrogenation, oxidation,
decomposition, and isomerization.8
A case study has been
presented of a fixed bed where UV-vis spectroscopy (diffuse
reflectance spectroscopy) and Raman spectroscopy have been
used to describe changes in the Cr/Al2O3 active catalyst species
by increases observed in specific peaks.9
These techniques have
also been used to track the formation of coke to maintain an
active catalyst and using this information to control the
regeneration.2
Combining spectroscopic techniques provides
complementary quantification of the state of the catalyst and
the changes occurring under reaction conditions.10
However,
these studies have all focused on fixed beds although the Raman
spectral information from moving particles in a fluidized bed
may be an attractive measure for catalysts and adsorbates to
monitor and avoid the formation of coke.11
An example using
spectroscopy techniques to characterize the state of a slurry
catalyst (Cr/SiO2) for the polymerization of ethylene, using
toluene as a solvent has been illustrated.12
Here the Raman
spectra of toluene dominate the spectra collected from the
reaction mixture and thus obscure the spectra from the catalytic
active material.
UV-vis spectroscopy using visible light gives information
regarding the electronic d-d and charge transfer transitions of
metal oxides. It provides a convenient method to probe the state
* To whom correspondence should be addressed. E-mail:
T.A.Nijhuis@tue.nl.
Ind. Eng. Chem. Res. XXXX, xxx, 000 A
10.1021/ie801984w CCC: $40.75 XXXX American Chemical Society
2. of the active metal oxide catalyst or an adsorbed pH indicator.
By the application of small optical probes, measurement is
relatively easy and may also be performed through the outer
wall of the reactor if made of glass.9
Raman spectroscopy using
laser light provides information regarding the vibrational spectra
of metal oxides and organic deposits, and optical probes based
on Raman spectroscopy are becoming readily available.
Multiphase Reactors. The added effect of gas-liquid and
liquid-solid interfaces in gas-liquid-solid reactors contributes
to the spectroscopic information collected and thus poses a
challenge in obtaining reliable spectroscopic information from
the catalyst deposited on the solid surface. Optical probes use
optical fibers to transmit light (from a laser or lamp) into the
reactor and another in the same fiber bundle to measure the
reflected light (connected to a spectrometer). The interfer-
ence of the liquid-solid and the gas-liquid interfaces with the
light reflected from the catalyst on the solid surface is described
schematically for slurry reactors and packed bubble columns
in Figures 1a and 1b, respectively. These interferences need to
be removed from the spectroscopic information collected to
successfully determine the state of the catalyst.
Model System. The aim is to develop a methodology for
characterization of the solid catalyst in a multiphase system.
Since transitions in the state of a real catalyst are usually very
slow and occur at high temperature or pressure, a model system
is used as a more convenient and controllable way to demon-
strate the concept. An insoluble pH indicator adsorbed on the
surface of a solid support is used in this study to simulate an
active catalyst to determine UV-vis and Raman spectra in
multiphase systems with relative ease. The pH indicator exhibits
different UV-vis and Raman spectra depending on the pH of
the liquid with which it is in contact. This system thus provides
a method of studying spectroscopic measurements at mild
conditions (ambient temperature and pressure). The spectra
collected are only from the surface of the solid particles or solid
support and the contribution of the liquid to the spectra is low
due the low solubility of the pH indicator. The characteristic
peaks in the UV-vis and Raman are specific to the current
system. The origin of these characteristic peaks will not be
discussed in detail here, since this paper focuses on the
description of a methodology to do spectroscopy on a (moving)
catalyst in a multiphase reactor system. The chemical origin of
the bands/vibrations are less relevant and the discussion thereof
is beyond the scope of this paper.
Experimental Details
The UV-vis experiments were performed using a reflection
probe consisting of a bundle of seven optical fibers (each 200
µm thick) encased in a steel tube (120 mm in length and 6 mm
in diameter). The central optical fiber is connected to a UV-vis
spectrometer (AvaSpec-2048-USB2, Avantes) and the remaining
six fibers are used for illumination and are connected to a light
source (AvaLight-D(H)-S Deuterium-Halogen light source,
215-2000 nm, Avantes). The calibration of the reflectance
spectrometer is performed using a white reference tile (WS-2,
Avantes). The UV-vis spectra were recorded in LabView
(LabView 7.0, National Instruments) at an integration time of
30 ms to decrease the noise to peak ratio.
The Raman experiments were performed using a reflection
probe consisting of a bundle of two optical fibers (200 µm
Figure 1. Schematic representation during operating conditions in (a) a
slurry reactor and (b) a packed bubble column, showing the interferences
at the gas-liquid and liquid-solid interfaces that scatter the light away
from the optical probe.
Figure 2. Images of a 40 ppi solid foam covered in TiO2 and insoluble pH indicator, bromocresol green, showing the acidity of the liquid medium, (a) acidic
and (b) basic. (c) Structure of bromocresol green in the acidic and basic states.
B Ind. Eng. Chem. Res., Vol. xxx, No. xx, XXXX
3. connected to spectrometer and 100 µm connected to the laser
source) encased in a steel tube (76 mm in length with 12.7 mm
diameter). This probe is connected to an integrated system
combining a laser source (532 nm) and a Raman spectrometer
(R-3000, Ocean Optics). The Raman spectra were recorded in
LabView (LabView 7.0, National Instruments) at integration
times between 1 and 5 s.
All chemicals used were laboratory grade supplied from
Merck unless specified otherwise. The pH of the liquid was
decreased using a solution of HCl (0.6 M) which was dosed
using a titrator (TIM854, Radiometer) at a rate of 0.2-5 mL/
min. The titrator also allowed measurement of the pH of the
liquid using a pH-electrode (pHC2001, Radiometer). The pH
indicator, bromocresol green (pH range 3.8-5.4), was dried onto
the solid particles (γ-Al2O3, 63-150 µm) or solid foam support
(40 ppi, ERG. Aerospace Corp.) from solution. This pH indicator
is usually dissolved in a liquid (a mixture of water and ethanol)
and exhibits different UV-vis and Raman spectra depending
on the liquid pH.
Slurry of Particles. Alumina particles (63-150 µm) covered
with bromocresol green were prepared using 5 wt % ethanol as
a solvent and dried in an oven at 90 °C from solution at a liquid
pH of approximately 5. The particles were filtered and washed
with distilled water until the filtrate remained clear. The pH
indicator has a low solubility in water and thus remains on the
surface of the particles and responds in the UV-vis and Raman
spectrum depending on the pH of the liquid surrounding the
particles.
Packed Bubble Column. Aluminum foam pieces (40 ppi,
ERG. Aerospace Corp.) were used as the packing material in
the packed bubble column experiments. Solid foams are
convenient to use due to the open structure and high surface
area for deposition of the pH indicator.13
The aluminum foam
was dipped in a slurry of TiO2 (17 wt %, P25, Degussa) and
dried while rotating at 60 rpm. Air was blown through the
samples to avoid pores of the solid foam material remaining
filled with the slurry. The solid foam pieces were calcined at
400 °C resulting in washcoats of approximately 7-10 wt %.
The bromocresol green pH indicator was applied to the surface
of the solid foam structure using the same preparation technique
described for the slurry particles, resulting in solid foams which
respond according to pH of the liquid medium, see Figure 2.
The bubble column used for the experiments is a cylindrical
glass vessel (diameter of 10 cm) where nitrogen is distributed
through a fritted glass disk from the bottom. The solid foam
was placed on the distributor and the UV-vis and Raman probes
focused on the solid foam packing from the top (approximately
2-5 mm focal distance). As gas bubbles travel through the solid
foam they interfere with the signal collected by the UV-vis
and Raman probes. Bubble interference was removed with an
in-house Labview application designed to discard compromised
UV-vis and Raman spectra. This method of tolerance-and-
averaging is described schematically in Figure 3. An average
spectrum (AS) is created over m (e.g., 10) number of spectra.
In the next cycle, the newly recorded spectrum (NS) is compared
to this averaged spectrum (ASold) for the UV-vis spectra over
wavelengths 300-800 nm and Raman spectra over Raman shifts
800-4300 cm-1
. The measurement is discarded if the sum of
the absolute difference between the spectra is larger than a set
tolerance value. This is repeated for the next nine (m - 1)
measurements. If, for example, three spectra were discarded, a
new average spectrum (ASnew) is created from the remaining
seven (n) spectra and used for comparison in the next cycle.
This procedure is repeated, producing a new average spectrum
for every 10 measurements. A spectrum averaged over a too
large number of spectra (e.g., m equal to 100) will have less
noise, but also rapid changes in the state of the pH indicator
are possibly evaluated as the interference of a bubble and thus
could be lost.
Results and Discussion
Slurry of Particles. A slurry of 30 wt % alumina particles
with the bromocresol green pH indicator adsorbed to the
particles’ surface was used to evaluate if UV-vis and Raman
spectroscopy could be used to determine changes in the state
of the pH indicator. UV-vis spectra were recorded every 200
ms while the pH of the liquid was decreased from 4 to 1 over
a time period of 300 s. The UV-vis spectra of the slurry of
bromocresol green particles are given in Figure 4 for a select
number of liquid pH values. The reflectance at 620 and 450
nm increases and decreases, respectively, as the pH is decreased.
Raman spectra were recorded every 15 s (integration time 5 s),
while the pH of the liquid was decreased from 4 to 1 over a
time period of 300 s. The Raman spectra of the slurry of
bromocresol green particles are given in Figure 5. Raman
intensities are observed to increase (at approximately 833, 1570,
2210, 2680, 3040, and 4000 cm-1
) as a result of the bromocresol
green changing from the basic to the acidic state with the
decrease in the liquid pH (addition of H+
) (see Figure 2c for
the structural changes). Thus, the UV-vis and Raman spectra
Figure 3. Schematic representation of the tolerance-and-averaging method
to remove bubble interference from UV-vis spectra. New spectra (NS)
from the spectrometer are compared to an average spectrum (AS) determined
over m spectra over the previous cycle. The sum of the absolute difference
is compared to a tolerance value (Tol) and if larger, the spectrum is
discarded. A new average is created from the n number of spectra remaining
and is used in the next cycle.
Figure 4. Observed UV-vis reflectance spectra for a 30% slurry of particles
covered with bromocresol green, while the pH of the liquid is decreased.
Ind. Eng. Chem. Res., Vol. xxx, No. xx, XXXX C
4. can be obtained from moving particles, and transients from one
state to another can be observed.
Packed Bubble Column. The experiments for the UV-vis
and Raman spectra resulting from the adsorbed bromocresol
green pH indicator operating in a packed bubble column are
shown in Figure 6-Figure 8. Fifty UV-vis spectra are recorded
every 2 s and the tolerance-and-averaging method is used to
assess the validity of the recorded spectra. The Raman spectra
measurements are performed every 2 s and 10 are used for the
tolerance-and-averaging method. In Figure 6b the average
recorded UV-vis spectra for the wavelength 620 nm is given
while the liquid pH is decreased, see Figure 6c. As the bubble
flow starts and bubbles interfere with the UV-vis spectra and
Raman spectra obtained, the tolerance-and-averaging method
maintains the average spectral measurement while discarding
spectra compromised by bubbles. The average UV-vis spectra
determined using the tolerance-and-averaging method shows less
noise in the recorded spectra at 620 nm. The relative difference
between the average reflectance determined using all the spectra
and the average reflectance determined using the tolerance-and-
averaging method can be as high as 30-40% (see Figure 6d).
An increase in the UV-vis reflectance is observed as the liquid
pH is decreased (see Figure 4). Similarly, the changing Raman
intensity recorded at a Raman shift of 4000 cm-1
as a result of
decreasing liqiud pH is presented in Figure 7. A figure created
in a similar manner for one of the other characteristic bands
visible in the Raman spectrum for the slurry particles (at
approximately 833, 1570, 2210, 2680, 3040 cm-1
) yielded a
graph with a comparable trend. The average Raman intensity
increases as the pH of the liquid is decreased over time. As
much as 80% of spectra may be discarded using the tolerance-
and-averaging method resulting in an averaged Raman spectrum
Figure 5. (a) Observed Raman spectra for a 30 wt % slurry of particles covered with bromocresol green, while the pH of the liquid is decreased over time.
(b) Liquid pH-profile over time.
Figure 6. The UV-vis spectra obtained for the bromocresol green pH indicator deposited on the surface of a solid foam packing operating in a packed
bubble column. (a) Reflectance at a wavelength of 620 nm is presented. The spectra which have been discarded for averaging are given by the open symbols
(O) and used for determining the average in closed symbols (b). (b) The average reflectance of all data points (---) and the reflectance determined by the
tolerance-and-averaging method (s) are given. (c) Liquid pH-profile over time. (d) Relative error between the average for all the data points and the average
determined by the tolerance-and-averaging method.
D Ind. Eng. Chem. Res., Vol. xxx, No. xx, XXXX
5. with less noise when compared when all measurement are used.
In Figure 8 the averaged Raman spectra is given for a decrease
in the liquid pH over time. Comparing Figure 8 and Figure 5
shows that similar Raman intensities are observed to increase
as the bromocresol green pH indicator makes a transition to its
acidic form. The differences in the observed Raman spectra for
the slurry of particles and packed bubble column is due the pH
indicator being adsorbed onto two different materials, Al2O3
and TiO2, respectively.
Conclusions
UV-vis and Raman spectra recorded for a slurry of particles,
and a solid foam packed bubble column are shown for insoluble
pH indicators adsorbed onto the solid surface of the particles
and the solid foam packing. A change in the adsorbed pH
indicator is accomplished by a change in the liquid pH and
results in a clear change in the UV-vis and Raman spectra.
These examples indicate that, although the UV-vis and Raman
spectra are recorded under multiphase conditions, changes in
the solid surface conditions can be observed. In a packed bubble
column the averaging-and-tolerance method can be used to
remove spectra that have been compromised by gas-liquid
interfaces. The results from this study indicate that in situ
UV-vis and Raman spectroscopy can be used to characterize
a solid surface operating under multiphase conditions where
bubbles interfere with the measured spectra.
Acknowledgment
The authors gratefully acknowledge the Dutch Technology
Foundation STW (STW-NWO Vidi Project 06186) for the
financial support. Dow Benelux B.V., BASF Nederland B.V.,
Avantium Technologies, and Shell Global Solutions Interna-
tional B.V. are acknowledged for their input during the course
of the project.
Literature Cited
(1) Weckhuysen, B. M. In-Situ Spectroscopy of Catalysts; American
Scientific Publishers: Stevenson Ranch, CA, 2004.
(2) Bennici, S. M.; Vogelaar, B. M.; Nijhuis, T. A.; Weckhuysen, B. M.
Real-time control of a catalytic solid in a fixed-bed reactor based on in-situ
spectroscopy. Angew Chem., Int. Ed. 2007, 46, 5412–5416.
(3) Nijhuis, T. A.; Tinnemans, S. J.; Visser, T.; Weckhuysen, B. M.
Operando spectroscopic investigation of supported metal oxide catalysts
by combined time-resolved UV-VIS/Raman/on-line mass spectrometry.
Phys. Chem. Chem. Phys. 2003, 5, 4361–4365.
(4) Ramos, R. T.; Holmes, A.; Wu, X.; Dussan, E. A local optical probe
using fluorescence and reflectance for measurment of volume fractions in
multi-phase flows. Meas. Sci. Technol. 2001, 12, 871–876.
Figure 7. The Raman spectra obtained for the bromocresol green pH indicator deposited on the surface of a solid foam packing operating in a packed bubble
column. (a) Raman intensity at a Raman shift of 4000 cm-
1 is presented. The spectra which have been discarded for averaging are given by the open
symbols (O) and used for determining the average in closed symbols (b). (b) The average Raman spectra of all data points (---) and the average determined
by the tolerance-and-averaging method (s) are given. (c) Liquid pH-profile over time.
Figure 8. The average Raman spectra obtained for bromocresol green pH
indicator deposited on the surface of a solid foam packing operating in a
packed bubble column as the liquid pH is decreased over time. Peaks in
the Raman spectra are observed as the pH indicator undergoes transition to
its acidic form.
Ind. Eng. Chem. Res., Vol. xxx, No. xx, XXXX E
6. (5) Haw, J. F. In In-Situ Spectroscopy in Heterogeneous Catalysis;
Wiley-VCH: Weinheim, Germany, 2002.
(6) Weckhuysen, B. M. Snapshots of a working catalyst: possibilities
and limitations of in situ spectroscopy in the field of heterogeneous catalysis.
Chem. Commun. 2002, 97–110.
(7) Hunger, M.; Weitkamp, J. In situ IR, NMR, EPR, and UV-vis
Spectroscopy: Tools for New Insight into the Mechanisms of Heterogeneous
Catalysis. Angew Chem., Int. Ed. 2001, 40, 2954–2971.
(8) Weckhuysen, B. M.; Wachs, I. E. Catalysis by supported metal
oxides. In Handbook of Surface Interfaces of Materials; Academic Press:
San Diego, CA, 2001; Vol. 1, Chapter 11, pp 613-648.
(9) Nijhuis, T. A.; Tinnemans, S. J.; Visser, T.; Weckhuysen, B. M.
Towards real-time spectroscopic process control for the dehydrogenation
of propane over supported chromium oxide catalysts. Chem. Eng. Sci. 2004,
59, 5487–5492.
(10) Tinnemans, S. J.; Mesu, J. G.; Kervinen, K.; Visser, T.; Nijhuis,
T. A.; Beale, A. M.; Keller, D. E.; van der Eerden, A. M. J.; Weckhuysen,
B. M. Combining operando techniques in one spectroscopic-reaction cell:
oppertunities for elucidating the active site and related reaction mechanism
in catalysis. Catal. Today 2006, 113, 3–15.
(11) Chua, Y. T.; Stair, P. C. A novel fluidized bed technique for
measureing UV Raman spectra of catalysts and adsorbates. J. Catal. 2000,
196, 66–72.
(12) Weckhuysen, B. M. Determining the active site in a catalytic
process: Operando spectroscopy is more than a buzzword. Phys. Chem.
Chem. Phys. 2003, 5, 4351–4360.
(13) Stemmet, C. P.; Meeuwse, M.; van der Schaaf, J.; Kuster, B. F. M.;
Schouten, J. C. Gas-liquid mass transfer and axial dispersion in solid foam
packings. Chem. Eng. Sci. 2007, 62, 5444–5450.
ReceiVed for reView December 23, 2008
ReVised manuscript receiVed February 23, 2009
Accepted February 26, 2009
IE801984W
F Ind. Eng. Chem. Res., Vol. xxx, No. xx, XXXX