Autotuning for dcs800
•Download as DOCX, PDF•
0 likes•2,711 views
1. The document discusses how to perform autotuning for DC motors driven by a DCS800 controller. Autotuning can be done for the field current controller, armature current controller, and speed controller. 2. For autotuning the armature current controller, some interlocks must first be addressed including ensuring the main breaker is closed, the motor is uncoupled from equipment, and lubrication/hydraulic units for the equipment are running. 3. The procedure for autotuning the armature current controller involves switching the drive to local mode, setting a parameter to initiate armature current autotuning, activating an icon to open the shear breaker, and allowing the motor speed to reach base speed
Report
Share
Report
Share
![EFS-EM-BM 27-05-2014
Subject: How to perform AUTOTUNING for DC motors.
Equipment type: DC motors driven by DCS800.
Reported to: Eng. Ahmed Ali
Eng. Ahmed Nour Reported by: M Hassan
We can make Auto tuning for:
1-Field current controller: When the auto tuning is finished successfully
Will affect on [M1KpFex (44.02), M1TiFex (44.03) and M1PosLimCtrl (45.02)]
2-Armture current controller: When the auto tuning is finished successfully
Will affect on [M1KpArmCur (43.06), M1TiArmCur (43.07), M1DiscontCurLim (43.08), M1ArmLim
(43.09) and M1ArmR (43.10)]
3-Speed controller: When the auto tuning is finished successfully
Will affect on [KpS (24.03) and TiS (24.09)]
Note: The type of the selected auto tuning is detected upon the case we have.
In this report the auto tuning of the armature circuit will be discussed.
Before carrying out the procedure attention must be paid for some interlocks:
1- The main incoming circuit breaker to the panel (H05) must be closed.
2- The motor and the driven equipment must be uncoupled
Note: for our case” the shear”, the uncoupling is done by:
a- Decoupling the motor shaft & the shear shaft
b- The mechanical brake must be released
3- The lubrication unit, the greasing unit & the hydraulic unit which service the equipment must be run.](https://image.slidesharecdn.com/autotuningfordcs800-141001105710-phpapp01/85/Autotuning-for-dcs800-1-320.jpg)
Recommended
Furnace pressure control
This document discusses furnace pressure control for a circulating fluidized bed boiler. It describes how furnace pressure is measured by three pressure transmitters, with the average used as the process value for a proportional-integral controller. The controller output controls the inlet vanes of induced draft fans to keep furnace pressure stable. Furnace draft is controlled through the induced draft fan and inlet guide vanes or variable frequency drive. A two out of three selection block is used to select the two most accurate pressure transmitters and generate the process value for the PID controller, which compares the set point to the process value to control the final control elements of the induced draft fan.
ASH HANDLING PLANT
The document summarizes ash handling systems used in thermal power plants. It describes the two main types of ash - bottom ash and fly ash. Bottom ash is heavier and collected at the bottom of furnaces while fly ash is lighter and carried by flue gases. Wet and dry handling systems are used to transport and store bottom ash and fly ash. Ash is an important byproduct that can be utilized in cement, bricks and construction if handled properly through integrated ash handling systems.
Condenser in thermal power plants
The document discusses condensers used in thermal power plants. It describes the functions of a condenser as condensing exhaust steam from turbines to be reused in the steam cycle, creating a vacuum to improve turbine efficiency, and removing non-condensable gases. Key aspects covered include the condenser's role in the Rankine cycle, operation, materials used for tubes, sources of air leakage, methods for detecting water leakage into tubes, and cleaning and testing of condenser tubes.
Lesson 14-idlers-and-pulleys
This document discusses idlers and pulleys used in conveyor systems. It describes different types of idlers like carry idlers and return idlers, and their purposes in shaping the belt load and supporting the belt. It discusses CEMA classifications for idlers and common idler diameters. It also describes factors involved in selecting idlers like idler load, belt tension, and misalignment load. For pulleys, it discusses types like drum and wing pulleys and their purpose in transmitting power and changing belt direction. It covers CEMA duty classifications and describes pulley lagging used to increase traction. The document concludes with discussing belt tensions at different locations and how to select pulley diameter based on wrap angle and belt tension.
304372123-4-Kiln-Supports.pdf
This document discusses rotary kiln maintenance, focusing on kiln supports and roller adjustments. It describes different types of kiln supports, including rigid, pivoting, and self-aligning supports. It explains how to properly adjust the rollers to push the kiln uphill and avoid overloading the thrust roller. Methods for measuring roller thrust and inclination are provided. Precise roller adjustments and monitoring of thrust forces are important for optimal kiln operation.
Liners
The document discusses engine components including liners and pistons. It describes two types of liners - dry liners which are thin and fully supported by the block metal, and wet liners which are pressed into the bore and supported at the top and bottom, allowing direct contact with cooling water. It also discusses pistons and various methods to control piston slap, such as using slots, dams, split skirts, tapered pistons, special alloys, and bi-metal pistons.
Manuel diapositivas[1]
Este documento proporciona una descripción general de las bandas transportadoras, incluidas sus características, partes, ventajas y desventajas. Las bandas transportadoras son máquinas formadas por cintas sin fin que se usan para transportar materiales. Se componen de una cinta, rodillos y motores eléctricos. Son útiles para la minería debido a su capacidad para transportar materiales a lo largo de largas distancias y pendientes empinadas. El documento también cubre consideraciones importantes para seleccionar el tipo y
valve maintenance-packing-replacement
All valves require proper care and maintenance,as does other more complex equipment, to ensure theyare kept in optimum working order. The principledifficulties encountered with valves are leakage pastthe seat and disk, leakage at the stuffing box, stickingvalve stems, and loose valve disks.
Recommended
Furnace pressure control
This document discusses furnace pressure control for a circulating fluidized bed boiler. It describes how furnace pressure is measured by three pressure transmitters, with the average used as the process value for a proportional-integral controller. The controller output controls the inlet vanes of induced draft fans to keep furnace pressure stable. Furnace draft is controlled through the induced draft fan and inlet guide vanes or variable frequency drive. A two out of three selection block is used to select the two most accurate pressure transmitters and generate the process value for the PID controller, which compares the set point to the process value to control the final control elements of the induced draft fan.
ASH HANDLING PLANT
The document summarizes ash handling systems used in thermal power plants. It describes the two main types of ash - bottom ash and fly ash. Bottom ash is heavier and collected at the bottom of furnaces while fly ash is lighter and carried by flue gases. Wet and dry handling systems are used to transport and store bottom ash and fly ash. Ash is an important byproduct that can be utilized in cement, bricks and construction if handled properly through integrated ash handling systems.
Condenser in thermal power plants
The document discusses condensers used in thermal power plants. It describes the functions of a condenser as condensing exhaust steam from turbines to be reused in the steam cycle, creating a vacuum to improve turbine efficiency, and removing non-condensable gases. Key aspects covered include the condenser's role in the Rankine cycle, operation, materials used for tubes, sources of air leakage, methods for detecting water leakage into tubes, and cleaning and testing of condenser tubes.
Lesson 14-idlers-and-pulleys
This document discusses idlers and pulleys used in conveyor systems. It describes different types of idlers like carry idlers and return idlers, and their purposes in shaping the belt load and supporting the belt. It discusses CEMA classifications for idlers and common idler diameters. It also describes factors involved in selecting idlers like idler load, belt tension, and misalignment load. For pulleys, it discusses types like drum and wing pulleys and their purpose in transmitting power and changing belt direction. It covers CEMA duty classifications and describes pulley lagging used to increase traction. The document concludes with discussing belt tensions at different locations and how to select pulley diameter based on wrap angle and belt tension.
304372123-4-Kiln-Supports.pdf
This document discusses rotary kiln maintenance, focusing on kiln supports and roller adjustments. It describes different types of kiln supports, including rigid, pivoting, and self-aligning supports. It explains how to properly adjust the rollers to push the kiln uphill and avoid overloading the thrust roller. Methods for measuring roller thrust and inclination are provided. Precise roller adjustments and monitoring of thrust forces are important for optimal kiln operation.
Liners
The document discusses engine components including liners and pistons. It describes two types of liners - dry liners which are thin and fully supported by the block metal, and wet liners which are pressed into the bore and supported at the top and bottom, allowing direct contact with cooling water. It also discusses pistons and various methods to control piston slap, such as using slots, dams, split skirts, tapered pistons, special alloys, and bi-metal pistons.
Manuel diapositivas[1]
Este documento proporciona una descripción general de las bandas transportadoras, incluidas sus características, partes, ventajas y desventajas. Las bandas transportadoras son máquinas formadas por cintas sin fin que se usan para transportar materiales. Se componen de una cinta, rodillos y motores eléctricos. Son útiles para la minería debido a su capacidad para transportar materiales a lo largo de largas distancias y pendientes empinadas. El documento también cubre consideraciones importantes para seleccionar el tipo y
valve maintenance-packing-replacement
All valves require proper care and maintenance,as does other more complex equipment, to ensure theyare kept in optimum working order. The principledifficulties encountered with valves are leakage pastthe seat and disk, leakage at the stuffing box, stickingvalve stems, and loose valve disks.
Bearing failure and its Causes and Countermeasures
A brief review about bearing and failure of its various parts due to other possibilities than design such as manufacturing, improper service and handling and other similar aspects.
Sliding contact bearing
1. The document discusses sliding contact bearings, which use a layer of lubricant like oil or grease to reduce friction and wear between moving machine elements.
2. Applications include concrete mixers, turbines, motors, and engine crankshafts. Advantages are simple design, compact size, low cost, and good shock resistance, while disadvantages include higher friction losses and need for good lubrication.
3. Bearings are classified by the direction of load (radial or thrust) and the type of contact (sliding or rolling). Sliding contact bearings use layers of materials like babbit metal, bronze, cast iron, or non-metallic alternatives between surfaces.
Lecture 4 - The Later Roman Bureaucracy
This document is a letter from the Roman governor's chancery, which was the administrative office that handled the governor's correspondence and record keeping, dated to the year AD 342. The letter likely pertains to official government business in the province and was drafted and sent out by a scribe or clerk working in the governor's chancery office.
Torque converter
The document discusses the torque converter and its role in automatic transmissions. It explains that the torque converter uses transmission fluid to transfer power from the engine to the transmission hydrodynamically. The torque converter contains an impeller connected to the engine, a turbine connected to the transmission input shaft, and a stator that redirects the fluid flow to multiply torque. The automatic transmission also contains a planetary gearset and hydraulic controls to shift gears without a clutch pedal.
Calculo de valvula de expansion
SE DESCRIBE EL MÉTODO POR EL CUAL SE OBTIENE UNA VÁLVULA DE EXPANSIÓN PARA LOS DIFERENTES TIPOS DE EQUIPOS DE AIRE ACONDICIONADO Y SIS DIFERENTES CARACTERÍSTICAS DEPENDIENDO EL TIPO DE GAS Y EL USO QUE SE LA VA A DAR AL EQUIPO
Training material for ash handling system (fly)
The document provides an overview of Clyde Bergemann Materials Handling Ltd.'s ash conveying system for a power plant in Mong Duong, Vietnam. It describes the key components of the system including pneumatic conveying technology using MD-Pumps and ash vessels to transfer ash from ESP fields and economizers/air heaters to silos for storage. It also outlines the operating cycles of the MD-Pumps and ash vessels, as well as the control system configuration and interfaces. Critical components like the dome valve are highlighted and their operation and maintenance are discussed at a high level.
All about boilers: Complete Basics, Classification of boilers,types
There are two main types of boilers: fire-tube and water-tube. Boilers are also classified as high-pressure or low-pressure and steam boiler or hot water boiler. The ideal boiler size just meets heating demands on the coldest day but most are oversized by 30% due to past calculation methods. Properly sized boilers allow for smaller, more efficient systems and reduced costs.
Central Cooling System (HT & LT).pptx
The document describes the central cooling water system used on ships. It has two interconnected freshwater circuits called the high temperature (HT) and low temperature (LT) circuits. The HT circuit cools the main and auxiliary engines while the LT circuit cools other machinery. Temperature is controlled through the use of 3-way valves that mix water from the LT and HT circuits. A seawater circuit with heat exchangers and pumps provides cooling to the freshwater circuits. The central cooling system provides both heating and cooling to ship systems in a simplified configuration compared to individual cooling arrangements.
Chapter 2 cooling system
The document provides an overview of engine cooling systems, including their purpose to remove excessive heat from the engine. It describes the two main types - air-cooled and water-cooled systems. The water-cooled system is discussed in more detail, outlining the key components like the radiator, water pump, thermostat and their functions in circulating coolant to cool the engine. Different types of coolant are also summarized.
Roller
1) Skew is the position of the roller axis with respect to the rotating drum axis. If they are parallel there is zero skew, if not parallel the roller is skewed and creates axial thrust on the drum.
2) Skewed rollers can accelerate wear by creating uneven load distribution, loss of contact and high stress points, and slipping/skidding between the roller and drum.
3) Understanding the bearing style is key to determining the axial position and direction of skew for each roller. Fixed plain sleeve bearings with thrust buttons can be checked by striking the end caps to identify which end has thrust.
Cooling system
The document discusses the key components and functions of a vehicle's cooling system. The cooling system works to quickly bring the engine up to operating temperature, maintain that temperature, and prevent overheating. It circulates coolant through the engine that absorbs heat and transfers it to the radiator where air flowing through cools the coolant so it can recirculate through the engine. Key components include the water pump, thermostat, radiator, hoses, and pressure cap. The cooling system regulates the engine's temperature to prevent damage from excessive heat.
lecture notes on Bearings
The document provides information on bearings for rotary motion. It discusses different types of bearings including radial bearings, thrust bearings, sliding contact bearings, and rolling contact bearings. It also discusses different classifications of sliding contact bearings based on load carried, lubrication, and lubrication mechanism. Common materials used for sliding contact bearings include babbitt metal, bronze, cast iron, carbon, rubber, wood, and plastic. The document concludes with an example problem demonstrating how to design a journal bearing for a centrifugal pump.
CMD Couplings
This document provides information on various types of flexible grid couplings produced by CMDCouplings, including:
- The Winflex coupling, which features a special hub tooth design that increases contact surface with the grid proportionally to torque to maintain constant contact pressure.
- A range of coupling types for different applications, such as single cover, spacer, and overrunning clutch types.
- Technical specifications and dimensions for different coupling sizes, including nominal torque ratings, keyway and bore dimensions, weights, and maximum speed ratings.
- Information on selecting the proper coupling size based on calculated torque requirements and compatibility with shaft speeds and bores.
Combustion control for Boiler (CFBC and Bagass Fired Boiler)
Auto Combustion Control for Boiler
In a Advance Environment Scenario of Power Generation in every area of the Power Plant Automatic Running of Equipment Play An Very Much Important Role.
To achieve this we implemented the advance system that is "Boiler Auto Combustion" which is implemented satisfactory in Andhra Sugar Limited Saggonda, Andhra Pradesh (1*33 MW CFBC Boiler Supplied by Thyssenkrupp Industries India Pvt Ltd Pune, Maharashtra.
Im here sharing the basic document for the Auto Combustion so that student who wish to learn it could understand better from this practically implemented logic diagram.
Thank you.
Your
Ashish Kinkar
3 hydrolastic
Hydrolastic suspension was a type of compact suspension system used in British cars in the 1960s-1970s. It used fluid-filled displacer units attached to each wheel to provide a smooth ride. The key components of the displacer unit included two fluid chambers separated by a flexible diaphragm and piston, which bore the wheel load. Fluid could pass through holes between the chambers to allow movement and dampening of the suspension in response to road conditions. Cars that featured the Hydrolastic suspension system included various Mini, Austin, and Morris models.
Introduction of Boiler
A boiler is a closed vessel that heats water or another fluid. Boilers are constructed from low-carbon steel and have corrugated furnaces for strength. On ships, steam is used for heating, powering turbines, pumps, and other machinery. There are different types of boilers classified by their orientation, circulation method, pressure rating, and whether water or hot gases pass through tubes. Fire tube boilers have hot gases passing through tubes surrounded by water while water tube boilers have water passing through tubes surrounded by hot gases. Packaged boilers are self-contained and efficient units that produce steam quickly.
Resolución 2492 de 2022.pdf
Por la cual se establece el reglamento técnico sobre los requisitos de etiquetado nutricional y frontal que deben cumplir los alimentos envasados o empacados para consumo humano
AUTOMATIC TURBINE RUNUP SYSTEM
The document discusses steam turbine control and instrumentation. It describes various types of steam turbines including conventional cycle, combined cycle, and nuclear turbines ranging from 210MW to 800MW. It then discusses the aims of automation in steam turbines, including improved control quality, increased plant availability and efficiency. The document outlines the main subsystems of steam turbine control including control systems, monitoring and measurement systems, and protection systems. It provides details on an Automatic Turbine Run-Up System (ATRS) which automatically controls the start-up process. The ATRS utilizes functional group control philosophy and consists of sub-group controls, sub-loop controls, and drive interface controls. It also describes the turbine protection system and various tripping criteria to
Types of Dynamometers
Introduction of dynamomter which is mention below:
Absorption dynamometer
Prony brake dynamometer
Rope brake dynamometer
Transmission dynamometer
Belt transmission dynamometer
Epicyclic dynamometer
Torsion dynamometer
Comparison of turbocharger and supercharger
The document compares turbochargers and superchargers. It states that turbochargers are driven by exhaust gases and are more efficient, but take time to reach operating speed after throttle opening. Superchargers are driven mechanically by the engine and are less efficient, but provide an instantaneous power increase. The key difference is that turbochargers are powered by exhaust gas turbine, while superchargers are mechanically driven, often by a belt connected to the crankshaft.
ABB DRIVES_Drive control unit "RDCU_12-C"
1. The document analyzes the configuration of drive control units (RDCU-12C) for various equipment on two bar mills. It identifies differences in device types that need to be addressed.
2. To configure RDCU cards with device type "NONE", backup files were created and restored to these cards from installed cards of known device types. This allowed standardizing three cards for use.
3. Additional testing showed RDCU cards can be overwritten, allowing backup files and parameters to be downloaded from one drive to configure another drive's card, changing the device type registered on the card. This finding allows flexible use of spare cards across different drive types on the mills.
Tips for Technical Illustration
What if you need to add technical illustrations or create illustrations from scratch for documentation? This presentation includes tips & suggestions.
More Related Content
What's hot
Bearing failure and its Causes and Countermeasures
A brief review about bearing and failure of its various parts due to other possibilities than design such as manufacturing, improper service and handling and other similar aspects.
Sliding contact bearing
1. The document discusses sliding contact bearings, which use a layer of lubricant like oil or grease to reduce friction and wear between moving machine elements.
2. Applications include concrete mixers, turbines, motors, and engine crankshafts. Advantages are simple design, compact size, low cost, and good shock resistance, while disadvantages include higher friction losses and need for good lubrication.
3. Bearings are classified by the direction of load (radial or thrust) and the type of contact (sliding or rolling). Sliding contact bearings use layers of materials like babbit metal, bronze, cast iron, or non-metallic alternatives between surfaces.
Lecture 4 - The Later Roman Bureaucracy
This document is a letter from the Roman governor's chancery, which was the administrative office that handled the governor's correspondence and record keeping, dated to the year AD 342. The letter likely pertains to official government business in the province and was drafted and sent out by a scribe or clerk working in the governor's chancery office.
Torque converter
The document discusses the torque converter and its role in automatic transmissions. It explains that the torque converter uses transmission fluid to transfer power from the engine to the transmission hydrodynamically. The torque converter contains an impeller connected to the engine, a turbine connected to the transmission input shaft, and a stator that redirects the fluid flow to multiply torque. The automatic transmission also contains a planetary gearset and hydraulic controls to shift gears without a clutch pedal.
Calculo de valvula de expansion
SE DESCRIBE EL MÉTODO POR EL CUAL SE OBTIENE UNA VÁLVULA DE EXPANSIÓN PARA LOS DIFERENTES TIPOS DE EQUIPOS DE AIRE ACONDICIONADO Y SIS DIFERENTES CARACTERÍSTICAS DEPENDIENDO EL TIPO DE GAS Y EL USO QUE SE LA VA A DAR AL EQUIPO
Training material for ash handling system (fly)
The document provides an overview of Clyde Bergemann Materials Handling Ltd.'s ash conveying system for a power plant in Mong Duong, Vietnam. It describes the key components of the system including pneumatic conveying technology using MD-Pumps and ash vessels to transfer ash from ESP fields and economizers/air heaters to silos for storage. It also outlines the operating cycles of the MD-Pumps and ash vessels, as well as the control system configuration and interfaces. Critical components like the dome valve are highlighted and their operation and maintenance are discussed at a high level.
All about boilers: Complete Basics, Classification of boilers,types
There are two main types of boilers: fire-tube and water-tube. Boilers are also classified as high-pressure or low-pressure and steam boiler or hot water boiler. The ideal boiler size just meets heating demands on the coldest day but most are oversized by 30% due to past calculation methods. Properly sized boilers allow for smaller, more efficient systems and reduced costs.
Central Cooling System (HT & LT).pptx
The document describes the central cooling water system used on ships. It has two interconnected freshwater circuits called the high temperature (HT) and low temperature (LT) circuits. The HT circuit cools the main and auxiliary engines while the LT circuit cools other machinery. Temperature is controlled through the use of 3-way valves that mix water from the LT and HT circuits. A seawater circuit with heat exchangers and pumps provides cooling to the freshwater circuits. The central cooling system provides both heating and cooling to ship systems in a simplified configuration compared to individual cooling arrangements.
Chapter 2 cooling system
The document provides an overview of engine cooling systems, including their purpose to remove excessive heat from the engine. It describes the two main types - air-cooled and water-cooled systems. The water-cooled system is discussed in more detail, outlining the key components like the radiator, water pump, thermostat and their functions in circulating coolant to cool the engine. Different types of coolant are also summarized.
Roller
1) Skew is the position of the roller axis with respect to the rotating drum axis. If they are parallel there is zero skew, if not parallel the roller is skewed and creates axial thrust on the drum.
2) Skewed rollers can accelerate wear by creating uneven load distribution, loss of contact and high stress points, and slipping/skidding between the roller and drum.
3) Understanding the bearing style is key to determining the axial position and direction of skew for each roller. Fixed plain sleeve bearings with thrust buttons can be checked by striking the end caps to identify which end has thrust.
Cooling system
The document discusses the key components and functions of a vehicle's cooling system. The cooling system works to quickly bring the engine up to operating temperature, maintain that temperature, and prevent overheating. It circulates coolant through the engine that absorbs heat and transfers it to the radiator where air flowing through cools the coolant so it can recirculate through the engine. Key components include the water pump, thermostat, radiator, hoses, and pressure cap. The cooling system regulates the engine's temperature to prevent damage from excessive heat.
lecture notes on Bearings
The document provides information on bearings for rotary motion. It discusses different types of bearings including radial bearings, thrust bearings, sliding contact bearings, and rolling contact bearings. It also discusses different classifications of sliding contact bearings based on load carried, lubrication, and lubrication mechanism. Common materials used for sliding contact bearings include babbitt metal, bronze, cast iron, carbon, rubber, wood, and plastic. The document concludes with an example problem demonstrating how to design a journal bearing for a centrifugal pump.
CMD Couplings
This document provides information on various types of flexible grid couplings produced by CMDCouplings, including:
- The Winflex coupling, which features a special hub tooth design that increases contact surface with the grid proportionally to torque to maintain constant contact pressure.
- A range of coupling types for different applications, such as single cover, spacer, and overrunning clutch types.
- Technical specifications and dimensions for different coupling sizes, including nominal torque ratings, keyway and bore dimensions, weights, and maximum speed ratings.
- Information on selecting the proper coupling size based on calculated torque requirements and compatibility with shaft speeds and bores.
Combustion control for Boiler (CFBC and Bagass Fired Boiler)
Auto Combustion Control for Boiler
In a Advance Environment Scenario of Power Generation in every area of the Power Plant Automatic Running of Equipment Play An Very Much Important Role.
To achieve this we implemented the advance system that is "Boiler Auto Combustion" which is implemented satisfactory in Andhra Sugar Limited Saggonda, Andhra Pradesh (1*33 MW CFBC Boiler Supplied by Thyssenkrupp Industries India Pvt Ltd Pune, Maharashtra.
Im here sharing the basic document for the Auto Combustion so that student who wish to learn it could understand better from this practically implemented logic diagram.
Thank you.
Your
Ashish Kinkar
3 hydrolastic
Hydrolastic suspension was a type of compact suspension system used in British cars in the 1960s-1970s. It used fluid-filled displacer units attached to each wheel to provide a smooth ride. The key components of the displacer unit included two fluid chambers separated by a flexible diaphragm and piston, which bore the wheel load. Fluid could pass through holes between the chambers to allow movement and dampening of the suspension in response to road conditions. Cars that featured the Hydrolastic suspension system included various Mini, Austin, and Morris models.
Introduction of Boiler
A boiler is a closed vessel that heats water or another fluid. Boilers are constructed from low-carbon steel and have corrugated furnaces for strength. On ships, steam is used for heating, powering turbines, pumps, and other machinery. There are different types of boilers classified by their orientation, circulation method, pressure rating, and whether water or hot gases pass through tubes. Fire tube boilers have hot gases passing through tubes surrounded by water while water tube boilers have water passing through tubes surrounded by hot gases. Packaged boilers are self-contained and efficient units that produce steam quickly.
Resolución 2492 de 2022.pdf
Por la cual se establece el reglamento técnico sobre los requisitos de etiquetado nutricional y frontal que deben cumplir los alimentos envasados o empacados para consumo humano
AUTOMATIC TURBINE RUNUP SYSTEM
The document discusses steam turbine control and instrumentation. It describes various types of steam turbines including conventional cycle, combined cycle, and nuclear turbines ranging from 210MW to 800MW. It then discusses the aims of automation in steam turbines, including improved control quality, increased plant availability and efficiency. The document outlines the main subsystems of steam turbine control including control systems, monitoring and measurement systems, and protection systems. It provides details on an Automatic Turbine Run-Up System (ATRS) which automatically controls the start-up process. The ATRS utilizes functional group control philosophy and consists of sub-group controls, sub-loop controls, and drive interface controls. It also describes the turbine protection system and various tripping criteria to
Types of Dynamometers
Introduction of dynamomter which is mention below:
Absorption dynamometer
Prony brake dynamometer
Rope brake dynamometer
Transmission dynamometer
Belt transmission dynamometer
Epicyclic dynamometer
Torsion dynamometer
Comparison of turbocharger and supercharger
The document compares turbochargers and superchargers. It states that turbochargers are driven by exhaust gases and are more efficient, but take time to reach operating speed after throttle opening. Superchargers are driven mechanically by the engine and are less efficient, but provide an instantaneous power increase. The key difference is that turbochargers are powered by exhaust gas turbine, while superchargers are mechanically driven, often by a belt connected to the crankshaft.
What's hot (20)
Bearing failure and its Causes and Countermeasures
Bearing failure and its Causes and Countermeasures
All about boilers: Complete Basics, Classification of boilers,types
All about boilers: Complete Basics, Classification of boilers,types
Combustion control for Boiler (CFBC and Bagass Fired Boiler)
Combustion control for Boiler (CFBC and Bagass Fired Boiler)
Viewers also liked
ABB DRIVES_Drive control unit "RDCU_12-C"
1. The document analyzes the configuration of drive control units (RDCU-12C) for various equipment on two bar mills. It identifies differences in device types that need to be addressed.
2. To configure RDCU cards with device type "NONE", backup files were created and restored to these cards from installed cards of known device types. This allowed standardizing three cards for use.
3. Additional testing showed RDCU cards can be overwritten, allowing backup files and parameters to be downloaded from one drive to configure another drive's card, changing the device type registered on the card. This finding allows flexible use of spare cards across different drive types on the mills.
Tips for Technical Illustration
What if you need to add technical illustrations or create illustrations from scratch for documentation? This presentation includes tips & suggestions.
Virus informaticos y antivirus
Existen muchos tipos de virus informáticos que desconocemos y que asechan a nuestros equipos; para ampliar mas el conocimiento sobre estos comparto la presentación sobre virus informáticos, tipos, historia; y antivirus con algunos de sus tipos
Follow me videos 1 60
The document discusses the history and development of artificial intelligence over several decades. Early research focused on symbolic approaches using rules and logic but progress was slow. More recently, machine learning techniques such as deep learning have seen increasing success by learning from large amounts of data without being explicitly programmed. These new approaches are being applied to many areas and fueling a new wave of innovation and development in AI.
El xoloitzcuintle
El Xoloitzcuintle es una raza canina sin pelo originaria de México que era considerada sagrada por los aztecas. Requiere cuidados especiales para su piel desnuda como aplicar bloqueador solar y bañarlo regularmente. Existen tres tamaños y a pesar de no tener pelo es un buen perro de compañía y guardián.
Arquivos, Fluxos e Serialização de Objetos em Java
[1] O documento discute arquivos, fluxos de dados e serialização de objetos no Java, incluindo hierarquia de dados, classes File e Scanner/Formatter para E/S de arquivos, e serialização/desserialização usando ObjectInputStream/ObjectOutputStream.
[2] É descrito como programas manipulam dados em arquivos para persistência além da execução do programa, e como fluxos de dados representam a transferência desses dados.
[3] São explicados conceitos-chave como serialização para gravar/ler objetos inteiros em arquivos bin
Siemens 2016 Fiyat Listesi
Siemens 2016 Fiyat Listesi
Siemens 12 Ekim 2015 Fiyat Listesi
En Uygun İskontolar İçin Arayınız 0216 493 00 52
Fiyat Talepleriniz İçin: satis@berh.com.tr
Native Plants For Oregon’S Willamette Valley
This document provides information on native plant species suitable for landscaping in Oregon's Willamette Valley. It discusses the benefits of using native plants, which are already adapted to the local climate and provide food and habitat for wildlife. Several tree, shrub, groundcover and herbaceous plant species are described in detail, along with their characteristics, landscape uses, sunlight and moisture requirements. The document emphasizes matching plants to appropriate habitats and care during establishment, as well as enjoying the connection with nature that natives provide.
Up from slavery
This document provides a summary of each chapter of Booker T. Washington's autobiography "Up From Slavery". The summaries describe Washington's childhood in slavery, his struggle for education, his founding of the Tuskegee Institute in Alabama, his fundraising efforts for the school, and his influential Atlanta Compromise speech advocating for racial uplift through vocational education and economic prosperity rather than immediate political demands.
Manual cranio
Este manual fornece instruções sobre técnicas craniométricas e cranioscópicas, visando estabelecer uniformidade nos estudos cranianos. Inicialmente descreve os principais pontos craniométricos utilizados como referência anatômica para a medição do crânio. Em seguida, apresenta as principais medidas lineares, angulares e índices aplicados ao crânio e face. Por fim, fornece detalhes sobre análise dentária, idade biológica e dimorfismo sexual.
Thin Slices of Online Profile Attributes
The document reports on two studies that examined how people form impressions and make judgments based on thin slices of online profile information. In Study 1, participants were able to make predictive judgments about others based on only 5 attributes of brief online profiles that correlated with their judgments after viewing full profiles. Certain attributes like photos were viewed and relied on more than others. In Study 2, with a different task, similar results were found, with photos, interests, and about me sections being particularly important. The studies support the idea that people can make meaningful inferences from very little online profile information.
Retail Operations
The document discusses operations management in the retail sector, specifically the fashion industry. It notes that the supply chain is complex with many parties involved, requiring careful management. Fast fashion has become important for getting clothing to stores quickly within small lead times. The future challenge for retailers is to optimize costs and build trust in the supply chain through improved communication.
New york, new york lesson plan
The document provides a 1 day lesson plan for a 6th grade English class in New York City. The plan includes reading a text and watching a video about New York landmarks to improve reading comprehension. Students will then complete an online quiz and activity where they match images of landmarks to their names. The lesson aims to develop students' English linguistic skills while helping them learn about American culture. It incorporates group work, use of technology, and assessment through class participation and quiz results.
23 quotes that will inspire you to follow your dreams
You are never too old to follow your dreams. In this presentation, we have come up with the 23 inspirational and motivational quotes to encourage you to follow your dreams. Take the first step and always believe in your dreams.
OpenGL ES 2.0 Programming and Cocos2d-x v3.3 Rendering System
This document discusses OpenGL ES 2.0 programming and the Cocos2d-x v3.3 rendering system. It provides an overview of EGL and the OpenGL ES 2.0 pipeline, including vertex and fragment shaders. EGL acts as an interface between rendering APIs and platforms, providing mechanisms for creating rendering surfaces and graphics contexts.
Sangrias Word
Este documento explica cómo establecer diferentes tipos de sangrías en Microsoft Word, incluyendo sangrías izquierda, derecha, de primera línea y francesa. Describe métodos rápidos como usar la tecla TAB o los botones de sangría en la barra de herramientas. También explica cómo crear sangrías negativas y cómo establecer medidas precisas de sangría utilizando la regla y el cuadro de diálogo Formato de párrafo.
Aula 05
O documento discute os direitos fundamentais previstos na Constituição Federal de 1988, distinguindo direitos formais e materiais. Apresenta as cinco espécies de direitos fundamentais (individuais, sociais, da nacionalidade, políticos e dos partidos políticos) e explica que o rol de direitos na Constituição é exemplificativo, não taxativo.
Viewers also liked (20)
Arquivos, Fluxos e Serialização de Objetos em Java
Arquivos, Fluxos e Serialização de Objetos em Java
23 quotes that will inspire you to follow your dreams
23 quotes that will inspire you to follow your dreams
OpenGL ES 2.0 Programming and Cocos2d-x v3.3 Rendering System
OpenGL ES 2.0 Programming and Cocos2d-x v3.3 Rendering System
Similar to Autotuning for dcs800
Caterpillar engine speed timing sensor circuit test
This document provides troubleshooting information for issues related to the engine speed/timing sensors on a 3406E truck engine. It describes testing the sensor circuits if diagnostic codes related to the primary or secondary engine speed sensor are present. The procedure involves measuring the sensor resistance through the engine harness and inspecting the sensor installation and wiring harness if needed. Replacing stamped terminals in the wiring harness with machined terminals may resolve intermittent faults caused by issues with the wiring harness terminals.
SISTEMAS DE OPERACIÓN
The document discusses the electronic control system components of C27 and C32 industrial and petroleum engines. It describes the three types of electronic components - input, control, and output. Input components send signals to the ECM about engine conditions. The ECM processes these signals and supplies energy to output components like fuel injectors to control the engine. Sensors provide data to the ECM like temperature and pressure. This electronic system allows for improved engine performance and emissions control.
4 jh1+gestión+electrónica
1. The document provides information about the Isuzu 4JH1-TC diesel engine management system, which uses a Bosch VP44 injection pump controlled by an engine control module (ECM) and pump control unit (PSG) that communicate via CAN-bus.
2. The ECM controls fuel injection quantity and timing by exchanging data with the PSG, which actuates the injection pump. They share sensor data and commands via analog signals and CAN-bus.
3. The document outlines the components, electrical circuits, diagnostic procedures and trouble codes for technicians servicing the engine management system.
01 general information
The document summarizes information about the electronic control systems used in C27 and C32 engines for Caterpillar machines. It describes how the electronic fuel injection system improves efficiency and reduces emissions compared to mechanical systems. The engine is equipped with an electronic control module that monitors components and can detect faults. In cold conditions, the control module adjusts the fuel map and increases idle speed for clean exhaust. Customer-specified parameters can also be programmed into the control module.
Final presentation
This document proposes a system for the automatic remote control of an induction motor using a GSM-based system. Sensors will monitor the motor's line voltage, current, and temperature and send the data to a microcontroller for analysis. If any parameters exceed safe limits, the system will send an SMS alert and sound an alarm. It will provide protection against overvoltage, overcurrent, and overload. The goal is to develop a low-cost, compact system that allows remote two-way control and monitoring of the motor without needing highly skilled personnel.
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
This document provides service information about engine D8H, including:
- The engine is a 6-cylinder turbocharged diesel that meets Tier 4 emissions standards. It uses common rail fuel injection and an exhaust aftertreatment system.
- The electronic control unit (ECU) controls engine functions through the engine management system.
- The document describes engine components, identification information, lubrication, fuel, cooling, and other systems.
- It also outlines the engine protection functions of the ECU and warning indicators to protect the engine from damage.
- Procedures are provided for replacing the ECU, both for non-programmed and pre-programmed units, using the VCADS
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
The document provides service information for an engine. It describes the engine as a 6-cylinder turbocharged diesel engine that meets Tier 4 emissions standards. It also summarizes the engine's fuel, exhaust, cooling, and electronic control systems. The document then provides instructions for removing the engine, which involves draining fluids, disconnecting hoses and electrical connections, and removing mounting hardware.
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
This document provides service information about engine D8H, including:
1) Engine D8H is a 6-cylinder turbocharged diesel engine that meets Tier 4 interim emissions standards and features a common rail fuel system and exhaust aftertreatment system.
2) The engine has electronic engine controls and includes functions to protect the engine from damage during extreme operating conditions.
3) The document provides information on engine components, procedures for replacing the electronic control unit, and available VCADS Pro diagnostic operations.
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
The document provides service information about an engine. It describes the engine as a straight six-cylinder turbocharged diesel engine that meets Tier 4 emissions standards. It also summarizes the engine's electronic control system, exhaust aftertreatment system, and various engine protection functions. Removal procedures for the engine are outlined in over a dozen steps involving disconnecting various hoses, covers, and electrical connections.
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
The document provides service information for an engine. It describes the engine as a 6-cylinder turbocharged diesel engine that meets Tier 4 emissions standards. It also summarizes the engine's fuel, exhaust, cooling, and electronic control systems. The document then provides instructions for removing the engine, which involves draining fluids, disconnecting hoses and electrical connections, and removing mounting hardware.
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
The document provides service information for an engine. It describes the engine as a 6-cylinder turbocharged diesel engine that meets Tier 4 emissions standards. It also summarizes the engine's fuel, exhaust, cooling, and electronic control systems. The document then provides step-by-step instructions to remove the engine from the machine, which involves draining fluids, removing hoses, covers, and other components to access and detach the engine.
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
The document provides service information about an engine. It describes the engine as a 6-cylinder turbocharged diesel engine that meets Tier 4 emissions standards. It also summarizes the engine's electronic control system, exhaust aftertreatment system, and various protective functions. Procedures are provided for removing the engine, which involve draining fluids, disconnecting hoses and electrical connections, and removing mounting hardware.
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
This document provides service information about engine D8H, including:
- The engine is a 6-cylinder turbocharged diesel that meets Tier 4 emissions standards. It uses common rail fuel injection and an exhaust aftertreatment system.
- The electronic control unit (ECU) controls engine functions through the engine management system.
- The document describes engine components, identification information, lubrication, fuel, cooling, and other systems.
- It also outlines the engine protection functions of the ECU and warning indicators to protect the engine from damage.
- Procedures are provided for replacing the ECU, both for non-programmed and pre-programmed units, using the VCADS
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
The document provides service information about an engine. It describes the engine as a 6-cylinder turbocharged diesel engine that meets Tier 4 emissions standards. It also summarizes the engine's electronic control system, exhaust aftertreatment system, and various protective functions. Procedures are provided for removing the engine, which involve draining fluids, disconnecting hoses and electrical connections, and removing mounting hardware.
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
The document provides service information about an engine. It describes the engine as a 6-cylinder turbocharged diesel engine that meets Tier 4 emissions standards. It also summarizes the engine's electronic control system, exhaust aftertreatment system, and various protective functions. Procedures are provided for removing the engine, which involve draining fluids, disconnecting hoses and electrical connections, and removing mounting hardware.
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
The document provides service information for an engine. It describes the engine as a 6-cylinder turbocharged diesel engine that meets Tier 4 emissions standards. It also summarizes the engine's fuel, exhaust, cooling, and electronic control systems. The document then provides instructions for removing the engine, which involves draining fluids, disconnecting hoses and electrical connections, and removing mounting hardware.
Volvo EC300D NL EC300DNL Excavator Service Repair Manual Instant Download.pdf
The document provides service information about an engine. It describes the engine as a 6-cylinder 4-stroke turbocharged diesel engine that meets Tier 4 emissions standards. It has features like a common rail fuel system and exhaust aftertreatment system. The document provides information on removing the engine, which involves draining fluids, removing hoses, disconnecting electrical connections, and removing mounting hardware.
Volvo EC300D NL EC300DNL Excavator Service Repair Manual Instant Download.pdf
The document provides service information about engine D8H, including:
1) Engine D8H is a 6-cylinder turbocharged diesel engine meeting Tier 4 emissions standards, featuring common rail fuel injection and an exhaust aftertreatment system.
2) The engine has electronic engine controls and features like cooled EGR that help reduce emissions.
3) The document provides information on engine components, identification, protection functions, and diagnostic codes, and describes VCADS Pro operations for programming engine controls.
Volvo EC300D NL EC300DNL Excavator Service Repair Manual Instant Download.pdf
The document provides service information about an engine. It describes the engine as a 6-cylinder 4-stroke turbocharged diesel engine that meets Tier 4 emissions standards. It has features like a common rail fuel system and exhaust aftertreatment system. The document provides information on removing the engine, which involves draining fluids, removing hoses, disconnecting electrical connections, and removing mounting hardware.
Volvo EC300D NL EC300DNL Excavator Service Repair Manual Instant Download.pdf
The document provides service information about engine D8H, including:
1) Engine D8H is a 6-cylinder turbocharged diesel engine that meets Tier 4 interim emissions standards and features a common rail fuel system and exhaust aftertreatment system.
2) The engine has an electronic control unit that controls all electronic functions and contains functionality to protect the engine from damage during extreme operating conditions.
3) The document provides information on component locations, instructions for changing a non-programmed or pre-programmed electronic control unit, and lists available VCADS Pro operations for working on engine components and functions.
Similar to Autotuning for dcs800 (20)
Caterpillar engine speed timing sensor circuit test
Caterpillar engine speed timing sensor circuit test
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D NL EC300DNL Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D NL EC300DNL Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D NL EC300DNL Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D NL EC300DNL Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D NL EC300DNL Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D NL EC300DNL Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D NL EC300DNL Excavator Service Repair Manual Instant Download.pdf
Volvo EC300D NL EC300DNL Excavator Service Repair Manual Instant Download.pdf
Recently uploaded
cnn.pptx Convolutional neural network used for image classication
Convolutional Neural Network used for image classification
Comparative analysis between traditional aquaponics and reconstructed aquapon...
The aquaponic system of planting is a method that does not require soil usage. It is a method that only needs water, fish, lava rocks (a substitute for soil), and plants. Aquaponic systems are sustainable and environmentally friendly. Its use not only helps to plant in small spaces but also helps reduce artificial chemical use and minimizes excess water use, as aquaponics consumes 90% less water than soil-based gardening. The study applied a descriptive and experimental design to assess and compare conventional and reconstructed aquaponic methods for reproducing tomatoes. The researchers created an observation checklist to determine the significant factors of the study. The study aims to determine the significant difference between traditional aquaponics and reconstructed aquaponics systems propagating tomatoes in terms of height, weight, girth, and number of fruits. The reconstructed aquaponics system’s higher growth yield results in a much more nourished crop than the traditional aquaponics system. It is superior in its number of fruits, height, weight, and girth measurement. Moreover, the reconstructed aquaponics system is proven to eliminate all the hindrances present in the traditional aquaponics system, which are overcrowding of fish, algae growth, pest problems, contaminated water, and dead fish.
哪里办理(csu毕业证书)查尔斯特大学毕业证硕士学历原版一模一样
原版一模一样【微信：741003700 】【(csu毕业证书)查尔斯特大学毕业证硕士学历】【微信：741003700 】学位证，留信认证（真实可查，永久存档）offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原海外各大学 Bachelor Diploma degree, Master Degree Diploma
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
Advanced control scheme of doubly fed induction generator for wind turbine us...
This paper describes a speed control device for generating electrical energy on an electricity network based on the doubly fed induction generator (DFIG) used for wind power conversion systems. At first, a double-fed induction generator model was constructed. A control law is formulated to govern the flow of energy between the stator of a DFIG and the energy network using three types of controllers: proportional integral (PI), sliding mode controller (SMC) and second order sliding mode controller (SOSMC). Their different results in terms of power reference tracking, reaction to unexpected speed fluctuations, sensitivity to perturbations, and resilience against machine parameter alterations are compared. MATLAB/Simulink was used to conduct the simulations for the preceding study. Multiple simulations have shown very satisfying results, and the investigations demonstrate the efficacy and power-enhancing capabilities of the suggested control system.
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Climate change's impact on the planet forced the United Nations and governments to promote green energies and electric transportation. The deployments of photovoltaic (PV) and electric vehicle (EV) systems gained stronger momentum due to their numerous advantages over fossil fuel types. The advantages go beyond sustainability to reach financial support and stability. The work in this paper introduces the hybrid system between PV and EV to support industrial and commercial plants. This paper covers the theoretical framework of the proposed hybrid system including the required equation to complete the cost analysis when PV and EV are present. In addition, the proposed design diagram which sets the priorities and requirements of the system is presented. The proposed approach allows setup to advance their power stability, especially during power outages. The presented information supports researchers and plant owners to complete the necessary analysis while promoting the deployment of clean energy. The result of a case study that represents a dairy milk farmer supports the theoretical works and highlights its advanced benefits to existing plants. The short return on investment of the proposed approach supports the paper's novelty approach for the sustainable electrical system. In addition, the proposed system allows for an isolated power setup without the need for a transmission line which enhances the safety of the electrical network
一比一原版(CalArts毕业证)加利福尼亚艺术学院毕业证如何办理
CalArts毕业证学历书【微信95270640】CalArts毕业证’圣力嘉学院毕业证《Q微信95270640》办理CalArts毕业证√文凭学历制作{CalArts文凭}购买学历学位证书本科硕士,CalArts毕业证学历学位证【实体公司】办毕业证、成绩单、学历认证、学位证、文凭认证、办留信网认证、（网上可查，实体公司，专业可靠）
(诚招代理)办理国外高校毕业证成绩单文凭学位证,真实使馆公证（留学回国人员证明）真实留信网认证国外学历学位认证雅思代考国外学校代申请名校保录开请假条改GPA改成绩ID卡
1.高仿业务:【本科硕士】毕业证,成绩单（GPA修改）,学历认证（教育部认证）,大学Offer,,ID,留信认证,使馆认证,雅思,语言证书等高仿类证书；
2.认证服务: 学历认证（教育部认证）,大使馆认证（回国人员证明）,留信认证（可查有编号证书）,大学保录取,雅思保分成绩单。
3.技术服务：钢印水印烫金激光防伪凹凸版设计印刷激凸温感光标底纹镭射速度快。
办理加利福尼亚艺术学院加利福尼亚艺术学院毕业证文凭证书流程：
1客户提供办理信息：姓名生日专业学位毕业时间等（如信息不确定可以咨询顾问：我们有专业老师帮你查询）；
2开始安排制作毕业证成绩单电子图；
3毕业证成绩单电子版做好以后发送给您确认；
4毕业证成绩单电子版您确认信息无误之后安排制作成品；
5成品做好拍照或者视频给您确认；
6快递给客户（国内顺丰国外DHLUPS等快读邮寄）
-办理真实使馆公证（即留学回国人员证明）
-办理各国各大学文凭（世界名校一对一专业服务,可全程监控跟踪进度）
-全套服务：毕业证成绩单真实使馆公证真实教育部认证。让您回国发展信心十足！
（详情请加一下 文凭顾问+微信:95270640）欢迎咨询！子小伍玩小伍比山娃小一岁虎头虎脑的很霸气父亲让山娃跟小伍去夏令营听课山娃很高兴夏令营就设在附近一所小学山娃发现那所小学比自己的学校更大更美操场上还铺有塑胶跑道呢里面很多小朋友一班一班的快快乐乐原来城里娃都藏这儿来了怪不得平时见不到他们山娃恍然大悟起来吹拉弹唱琴棋书画山娃都不懂却什么都想学山娃怨自己太笨什么都不会斟酌再三山娃终于选定了学美术当听说每月要交元时父亲犹豫了山娃也说爸算了吧咱学校一学期才转
Software Engineering and Project Management - Introduction, Modeling Concepts...
Introduction, Modeling Concepts and Class Modeling: What is Object orientation? What is OO development? OO Themes; Evidence for usefulness of OO development; OO modeling history. Modeling
as Design technique: Modeling, abstraction, The Three models. Class Modeling: Object and Class Concept, Link and associations concepts, Generalization and Inheritance, A sample class model, Navigation of class models, and UML diagrams
Building the Analysis Models: Requirement Analysis, Analysis Model Approaches, Data modeling Concepts, Object Oriented Analysis, Scenario-Based Modeling, Flow-Oriented Modeling, class Based Modeling, Creating a Behavioral Model.
The Python for beginners. This is an advance computer language.
Python language is very important language at this time. we can easily understand this language by these notes.
IEEE Aerospace and Electronic Systems Society as a Graduate Student Member
IEEE Aerospace and Electronic Systems Society as a Graduate Student Member
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressions
K8sGPT is a tool that analyzes and diagnoses Kubernetes clusters. This presentation was used to share the requirements and dependencies to deploy K8sGPT in a local environment.
Data Driven Maintenance | UReason Webinar
Discover the latest insights on Data Driven Maintenance with our comprehensive webinar presentation. Learn about traditional maintenance challenges, the right approach to utilizing data, and the benefits of adopting a Data Driven Maintenance strategy. Explore real-world examples, industry best practices, and innovative solutions like FMECA and the D3M model. This presentation, led by expert Jules Oudmans, is essential for asset owners looking to optimize their maintenance processes and leverage digital technologies for improved efficiency and performance. Download now to stay ahead in the evolving maintenance landscape.
原版制作(Humboldt毕业证书)柏林大学毕业证学位证一模一样
原件一模一样【微信：bwp0011】《(Humboldt毕业证书)柏林大学毕业证学位证》【微信：bwp0011】学位证，留信认证（真实可查，永久存档）原件一模一样纸张工艺/offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原。
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问微bwp0011
【主营项目】
一.毕业证【微bwp0011】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【微bwp0011】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...
Medical image analysis has witnessed significant advancements with deep learning techniques. In the domain of brain tumor segmentation, the ability to
precisely delineate tumor boundaries from magnetic resonance imaging (MRI)
scans holds profound implications for diagnosis. This study presents an ensemble convolutional neural network (CNN) with transfer learning, integrating
the state-of-the-art Deeplabv3+ architecture with the ResNet18 backbone. The
model is rigorously trained and evaluated, exhibiting remarkable performance
metrics, including an impressive global accuracy of 99.286%, a high-class accuracy of 82.191%, a mean intersection over union (IoU) of 79.900%, a weighted
IoU of 98.620%, and a Boundary F1 (BF) score of 83.303%. Notably, a detailed comparative analysis with existing methods showcases the superiority of
our proposed model. These findings underscore the model’s competence in precise brain tumor localization, underscoring its potential to revolutionize medical
image analysis and enhance healthcare outcomes. This research paves the way
for future exploration and optimization of advanced CNN models in medical
imaging, emphasizing addressing false positives and resource efficiency.
Recently uploaded (20)
cnn.pptx Convolutional neural network used for image classication
cnn.pptx Convolutional neural network used for image classication
Comparative analysis between traditional aquaponics and reconstructed aquapon...
Comparative analysis between traditional aquaponics and reconstructed aquapon...
Introduction to AI Safety (public presentation).pptx
Introduction to AI Safety (public presentation).pptx
Advanced control scheme of doubly fed induction generator for wind turbine us...
Advanced control scheme of doubly fed induction generator for wind turbine us...
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Software Engineering and Project Management - Introduction, Modeling Concepts...
Software Engineering and Project Management - Introduction, Modeling Concepts...
4. Mosca vol I -Fisica-Tipler-5ta-Edicion-Vol-1.pdf
4. Mosca vol I -Fisica-Tipler-5ta-Edicion-Vol-1.pdf
The Python for beginners. This is an advance computer language.
The Python for beginners. This is an advance computer language.
IEEE Aerospace and Electronic Systems Society as a Graduate Student Member
IEEE Aerospace and Electronic Systems Society as a Graduate Student Member
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressions
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressions
Manufacturing Process of molasses based distillery ppt.pptx
Manufacturing Process of molasses based distillery ppt.pptx
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...
Autotuning for dcs800
- 1. EFS-EM-BM 27-05-2014 Subject: How to perform AUTOTUNING for DC motors. Equipment type: DC motors driven by DCS800. Reported to: Eng. Ahmed Ali Eng. Ahmed Nour Reported by: M Hassan We can make Auto tuning for: 1-Field current controller: When the auto tuning is finished successfully Will affect on [M1KpFex (44.02), M1TiFex (44.03) and M1PosLimCtrl (45.02)] 2-Armture current controller: When the auto tuning is finished successfully Will affect on [M1KpArmCur (43.06), M1TiArmCur (43.07), M1DiscontCurLim (43.08), M1ArmLim (43.09) and M1ArmR (43.10)] 3-Speed controller: When the auto tuning is finished successfully Will affect on [KpS (24.03) and TiS (24.09)] Note: The type of the selected auto tuning is detected upon the case we have. In this report the auto tuning of the armature circuit will be discussed. Before carrying out the procedure attention must be paid for some interlocks: 1- The main incoming circuit breaker to the panel (H05) must be closed. 2- The motor and the driven equipment must be uncoupled Note: for our case” the shear”, the uncoupling is done by: a- Decoupling the motor shaft & the shear shaft b- The mechanical brake must be released 3- The lubrication unit, the greasing unit & the hydraulic unit which service the equipment must be run.
- 2. The procedure of Auto tuning armature current controller is: 1-switch the drive to local mode 2-switch the parameter 99.06 from SERVICE MODE to ARMCUR AUTO 3-there is icon on the drive window program refers to closing the breaker of the shear, this action must be taken. 4- During the auto tuning the speed of the motor will reach to the base speed. 5-The time of the auto tuning does not exceed 2 seconds 6- If the auto tuning fails A121 AutotuneFail is set, repeat the auto tuning procedure