This document summarizes a research paper that proposes a new method for controlling parallel inverters using a synchronous reference frame virtual impedance loop. The proposed method aims to provide faster response and better current sharing accuracy compared to conventional droop control methods. It uses a synchronous reference frame virtual impedance loop and phase locked loop, rather than calculating active and reactive power. This avoids issues with droop control such as slow response times due to power calculation filters and sensitivity to line impedances. The control principle and performance analysis are examined through mathematical modeling and experimental testing of a parallel inverter system.
IRJET- Simulation and Experimental Verification of Single Phase Unity Power F...IRJET Journal
This document summarizes a research paper on simulating and experimentally verifying a single-phase unity power factor PWM boost rectifier with an improved voltage profile. The paper reviews various control techniques used in boost rectifiers, including peak current control, average current control, PI control, dynamic evolution control, and sliding mode control. It also discusses the advantages of achieving unity power factor, such as greater efficiency and power density. The proposed methodology involves analyzing different rectifier topologies and control schemes through simulation and experimental testing to develop a rectifier capable of unity power factor and low harmonic distortion. The results confirm that the independent and high-frequency operation of the converter allows for improved control loop bandwidth.
The power quality issue will take new dimension due to power system restructuring and shifting trend towards
distributed generation. Huge loss in terms of time and money has made power quality problems a major anxiety for modern
industries with non-linear loads in electrical power system. Power quality consists of a large number of disturbances such
as voltage sags, swells, harmonics, notch, flicker, etc. Power quality problems can be mitigated by many methods but most
appropriate solution to mitigate these problems is FACTS devices. In this paper a brief survey of FACTS devices are
presented which are used to mitigate power quality problems.
International Journal of Engineering and Science Invention (IJESI) inventionjournals
International Journal of Engineering and Science Invention (IJESI) is an international journal intended for professionals and researchers in all fields of computer science and electronics. IJESI publishes research articles and reviews within the whole field Engineering Science and Technology, new teaching methods, assessment, validation and the impact of new technologies and it will continue to provide information on the latest trends and developments in this ever-expanding subject. The publications of papers are selected through double peer reviewed to ensure originality, relevance, and readability. The articles published in our journal can be accessed online
Study of the performance of fault-tolerant multi-level inverter included in s...IJECEIAES
This document summarizes a study on the performance of a fault-tolerant multi-level inverter included in a shunt active power filter. The study proposes a new diagnostic method for detecting and locating open-circuit faults of IGBT switches in the inverter. The method uses mean value variations for early fault detection and trigonometric circle techniques for precise fault location. Simulation results show that the proposed diagnostic method can successfully detect and locate faults, and that the modified reconfigurable inverter topology allows continuity of filter currents with a short response time of 7 ms between diagnosis and reconfiguration.
Advance Technology in Application of Four Leg Inverters to UPQCIJPEDS-IAES
This article presents a novel application of four leg inverter with
conventional Sinusoidal Pulse Width Modulation (SPWM) Scheme to
Unified Power Quality Conditioner (UPQC). The Power Quality problem
became burning issues since the starting of high voltage AC transmission
system. Hence, in this article it has been discussed to mitigate the PQ issues
in high voltage AC systems through a three phase Unified Power Quality
Conditioner (UPQC) under various conditions, such as harmonic mitigation
scheme, non linear loads, sag and swell conditions as well. Also, it proposes
to control harmoincs with various artificial intelligent techniques. Thus
application of these control technique such as Neural Networks (ANN)
Fuzzy Logic makes the system performance in par with the standards
and also compared with existing system. The simulation results based on
MATLAB/Simulink are discussed in detail to support the concept developed
in the paper.
In power engineering the power flow analysis (also known as load flow study) is an important tool involving numerical analysis applied to a powe r system. This project deals with a model of existing power system using the actual data taking care of all parameters required for the simulation and analysis. With the help of Maharasht ra State Electricity Transmission co. Ltd.,a model of 220KV lines,of Solapur District grid usin g MATLAB software will be modeled. In this project,an algorithm will be used for power f low study and data collection and coding required for modeling. Load flow studies will be ca rried out using Newton Raphson method and voltage profile of buses will be analyzed. New meth od for the improvement of voltage profile will be suggested and analyze using the developed m odel. The optimization techniques include power factor compensation,tap changing,up gradati on of substation,up gradation of line and load shifting will be analyzed. Importance of power flow or Load flow studies is in planning future expansion of power system as well as determi ning the best operation of existing systems. From results of simulation buses with low voltage p rofile will be identified and possible solutions can be suggested.
Application of Unified Power Flow Controller in Nigeria Power System for Impr...ijtsrd
With the increased rate of urbanization and industrialization, the Nigerian electric power system is being put under pressure, high power losses which has led to fluctuation in voltage level. In this work the Nigeria 330Kv network of 42 bus system was considered. Data for the analysis were obtained from Transmission Company of Nigeria National Control Centre, Osogbo TCN and MATLAB PSAT software with newton Raphson's solution method embedded in it was used to carry out the analysis. The results of the analysis showed that many of the bus voltages were outside the voltage limits of ±5 i.e 0.95pu 1.05pu . After compensation with Flexible AC Transmission System devices FACTs namely Unified Power Flow Controller UPFC which can be used to control power flow on a transmission line, the voltage profile almost flat with bus voltages within acceptable voltage limits. It is also evident that the UPFC is device that can used to combat the voltage problem in the Nigerian electric power system. Adikaibe James | Prof. Engr. F. O. Enemuoh | Aghara Jachimma "Application of Unified Power Flow Controller in Nigeria Power System for Improvement of Voltage Profile" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-5 , August 2019, URL: https://www.ijtsrd.com/papers/ijtsrd27838.pdfPaper URL: https://www.ijtsrd.com/engineering/electrical-engineering/27838/application-of-unified-power-flow-controller-in-nigeria-power-system-for-improvement-of-voltage-profile/adikaibe-james
A fault-tolerant photovoltaic integrated shunt active power filter with a 27-...IJECEIAES
This paper introduces a fault-tolerant shunt active power filter (SAPF). The novility in of this work is that it poposes a solutions to increase the reliability of shunt active power filter to maintain its operation under a single-phase open-circuit fault in the SAPF. This will increase the reliability of the whole power system. The SAPF is composed of a 4-leg 27-level inverter based on asymmetric cascaded H-bridge topology. If an open-circuit fault is introduced to the operation of the SAPF, a special control technique will be implemented and the redundant leg of the SAPF will be activated. The faulttolerant SAPF can do many tasks under healthy operating conditions and post and open circuit fault depending on the state of charge (SOC) of the batteries. It can mitigate harmonics in the power system, improve power factor in the system by injecting reactive power, and inject real power to the system. The proposed SAPF is tested and simulated in MATLAB/Simulink and the results have shown a significant improvement in total harmonics distortion (THD) of the source current from 13.9% to 3.9% under the normal operating condition and from 42% to 8.4% post and open circuit fault.
IRJET- Simulation and Experimental Verification of Single Phase Unity Power F...IRJET Journal
This document summarizes a research paper on simulating and experimentally verifying a single-phase unity power factor PWM boost rectifier with an improved voltage profile. The paper reviews various control techniques used in boost rectifiers, including peak current control, average current control, PI control, dynamic evolution control, and sliding mode control. It also discusses the advantages of achieving unity power factor, such as greater efficiency and power density. The proposed methodology involves analyzing different rectifier topologies and control schemes through simulation and experimental testing to develop a rectifier capable of unity power factor and low harmonic distortion. The results confirm that the independent and high-frequency operation of the converter allows for improved control loop bandwidth.
The power quality issue will take new dimension due to power system restructuring and shifting trend towards
distributed generation. Huge loss in terms of time and money has made power quality problems a major anxiety for modern
industries with non-linear loads in electrical power system. Power quality consists of a large number of disturbances such
as voltage sags, swells, harmonics, notch, flicker, etc. Power quality problems can be mitigated by many methods but most
appropriate solution to mitigate these problems is FACTS devices. In this paper a brief survey of FACTS devices are
presented which are used to mitigate power quality problems.
International Journal of Engineering and Science Invention (IJESI) inventionjournals
International Journal of Engineering and Science Invention (IJESI) is an international journal intended for professionals and researchers in all fields of computer science and electronics. IJESI publishes research articles and reviews within the whole field Engineering Science and Technology, new teaching methods, assessment, validation and the impact of new technologies and it will continue to provide information on the latest trends and developments in this ever-expanding subject. The publications of papers are selected through double peer reviewed to ensure originality, relevance, and readability. The articles published in our journal can be accessed online
Study of the performance of fault-tolerant multi-level inverter included in s...IJECEIAES
This document summarizes a study on the performance of a fault-tolerant multi-level inverter included in a shunt active power filter. The study proposes a new diagnostic method for detecting and locating open-circuit faults of IGBT switches in the inverter. The method uses mean value variations for early fault detection and trigonometric circle techniques for precise fault location. Simulation results show that the proposed diagnostic method can successfully detect and locate faults, and that the modified reconfigurable inverter topology allows continuity of filter currents with a short response time of 7 ms between diagnosis and reconfiguration.
Advance Technology in Application of Four Leg Inverters to UPQCIJPEDS-IAES
This article presents a novel application of four leg inverter with
conventional Sinusoidal Pulse Width Modulation (SPWM) Scheme to
Unified Power Quality Conditioner (UPQC). The Power Quality problem
became burning issues since the starting of high voltage AC transmission
system. Hence, in this article it has been discussed to mitigate the PQ issues
in high voltage AC systems through a three phase Unified Power Quality
Conditioner (UPQC) under various conditions, such as harmonic mitigation
scheme, non linear loads, sag and swell conditions as well. Also, it proposes
to control harmoincs with various artificial intelligent techniques. Thus
application of these control technique such as Neural Networks (ANN)
Fuzzy Logic makes the system performance in par with the standards
and also compared with existing system. The simulation results based on
MATLAB/Simulink are discussed in detail to support the concept developed
in the paper.
In power engineering the power flow analysis (also known as load flow study) is an important tool involving numerical analysis applied to a powe r system. This project deals with a model of existing power system using the actual data taking care of all parameters required for the simulation and analysis. With the help of Maharasht ra State Electricity Transmission co. Ltd.,a model of 220KV lines,of Solapur District grid usin g MATLAB software will be modeled. In this project,an algorithm will be used for power f low study and data collection and coding required for modeling. Load flow studies will be ca rried out using Newton Raphson method and voltage profile of buses will be analyzed. New meth od for the improvement of voltage profile will be suggested and analyze using the developed m odel. The optimization techniques include power factor compensation,tap changing,up gradati on of substation,up gradation of line and load shifting will be analyzed. Importance of power flow or Load flow studies is in planning future expansion of power system as well as determi ning the best operation of existing systems. From results of simulation buses with low voltage p rofile will be identified and possible solutions can be suggested.
Application of Unified Power Flow Controller in Nigeria Power System for Impr...ijtsrd
With the increased rate of urbanization and industrialization, the Nigerian electric power system is being put under pressure, high power losses which has led to fluctuation in voltage level. In this work the Nigeria 330Kv network of 42 bus system was considered. Data for the analysis were obtained from Transmission Company of Nigeria National Control Centre, Osogbo TCN and MATLAB PSAT software with newton Raphson's solution method embedded in it was used to carry out the analysis. The results of the analysis showed that many of the bus voltages were outside the voltage limits of ±5 i.e 0.95pu 1.05pu . After compensation with Flexible AC Transmission System devices FACTs namely Unified Power Flow Controller UPFC which can be used to control power flow on a transmission line, the voltage profile almost flat with bus voltages within acceptable voltage limits. It is also evident that the UPFC is device that can used to combat the voltage problem in the Nigerian electric power system. Adikaibe James | Prof. Engr. F. O. Enemuoh | Aghara Jachimma "Application of Unified Power Flow Controller in Nigeria Power System for Improvement of Voltage Profile" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-5 , August 2019, URL: https://www.ijtsrd.com/papers/ijtsrd27838.pdfPaper URL: https://www.ijtsrd.com/engineering/electrical-engineering/27838/application-of-unified-power-flow-controller-in-nigeria-power-system-for-improvement-of-voltage-profile/adikaibe-james
A fault-tolerant photovoltaic integrated shunt active power filter with a 27-...IJECEIAES
This paper introduces a fault-tolerant shunt active power filter (SAPF). The novility in of this work is that it poposes a solutions to increase the reliability of shunt active power filter to maintain its operation under a single-phase open-circuit fault in the SAPF. This will increase the reliability of the whole power system. The SAPF is composed of a 4-leg 27-level inverter based on asymmetric cascaded H-bridge topology. If an open-circuit fault is introduced to the operation of the SAPF, a special control technique will be implemented and the redundant leg of the SAPF will be activated. The faulttolerant SAPF can do many tasks under healthy operating conditions and post and open circuit fault depending on the state of charge (SOC) of the batteries. It can mitigate harmonics in the power system, improve power factor in the system by injecting reactive power, and inject real power to the system. The proposed SAPF is tested and simulated in MATLAB/Simulink and the results have shown a significant improvement in total harmonics distortion (THD) of the source current from 13.9% to 3.9% under the normal operating condition and from 42% to 8.4% post and open circuit fault.
Line and Grid Impedance Impact on the Performances of a Parallel Connected Mo...IAES-IJPEDS
With the rising fuel cost, increasing demand of power and the concerns for global climate change, the use of clean energy make the connection of power electronics building bloc in the heart of the current research. The high output current applications make the parallel connection of modular inverters to be a solution for the use of low power building block inverters where the output power cannot be handled by a single inverter configuration. In this context, average-modeling using average phase–leg technique allows the n-parallel connected inverters to be analyzed accurately and rapidly without requiring the complexity of the full switched inverter topology. The obtained analytical solution along with the equivalent circuit model makes easier the design of the control loop. The analytical solution of the n-parallel connected inverters shows the impact of the line and grid impedance on the performance of the overall system. The impact of this coupling has to be investigated such that the main feature of paralleling inverters is guaranteed and that the inverter mode of operation will not be compromised. The main advantage of paralleling inverters can be lost for a certain coupling impedance considerations.
An Adaptive Virtual Impedance Based Droop Control Scheme for Parallel Inverte...IAES-IJPEDS
This document presents an adaptive virtual impedance based droop control scheme for parallel inverters in a microgrid. The scheme uses an impedance estimator to monitor changes in line impedances between inverters and the point of common coupling. It estimates the line impedance in real time using output voltages and currents of the inverters as well as voltages at the point of common coupling. The estimated line impedance is then fed into a virtual impedance loop to adjust the virtual impedance value and compensate for reactive power mismatches due to changing line impedances, improving power sharing performance. Simulation results show the effectiveness of the proposed adaptive scheme compared to conventional control methods.
A NOVEL TCHNOLOGY FOR HARMONICS AND UNBALANCE COMPENSATION IN ELECTRIC TRACTI...ijiert bestjournal
Power quality problems in power systems have been i mproved due to nonlinear loads. To compensate these problems Direct Power Compensator was proposed in this paper. A Direct Power Compensator (DPC) is proposed in this paper to elim inate the harmonic currents,compensate power factor and voltage unbalance problems created by th e nonlinear loads present in three phase systems. A DPC contains back to back converter by sharing th e same dc link power and v/v transformer to provide a voltage balance in transmission line. Hys teresis harmonic current regulator is used to produce pulse for back to back converter. A control ler maintains the dc-link voltage and compensates the power factor,harmonic currents. A comparative analysis for traction system with and without DPC was performed using MATLAB Simulink . Simulation results show the controller advantages and the applicability of the proposed me thod in railway systems.
IRJET- A Review on Solar based Multilevel Inverter with Three Phase Grid SupplyIRJET Journal
- The document discusses solar-powered multilevel inverters that can supply three-phase grid power. Multilevel inverters have advantages over single-level inverters like lower harmonic distortion, reduced electromagnetic interference, and the ability to operate at several voltage levels.
- The literature review covers prior research on different multilevel inverter topologies for photovoltaic systems, including the flying capacitor, neutral point clamped, and cascaded H-bridge inverters. It also discusses control methods like maximum power point tracking and modulation techniques.
- The goal is to develop a multilevel inverter powered by PV panels that can supply three-phase grid power with minimum harmonic distortion and reduced component requirements compared to
Mitigation of the Harmonics under Reactive Power Compensation by SHPF-TCR Usi...IJERA Editor
In this paper, a combined system of a thyristor-controlled reactor (TCR) and a shunt hybrid power filter
(SHPF)has been designed by MATLAB/SIMULINK approach for harmonic and reactive power compensation.
The quality of the power is effected by many factors like harmonic contamination, due to the increment of nonlinear
loads, sag and swell due to the switching of the loads etc. Also control schemes based on PI and Fuzzy
logic controllers have been proposed to mitigate the harmonics and neutral current . The proposed methodology
not only reduces the complexity but also offers simplicity to implement and increases reliability of the system.
These control strategies also help in achieving a low cost highly effective control. The performance is also
observed under influence of utility side disturbances such as harmonics, flicker and spikes with Non-Linear and
Reactive Loads with different control strategies.
Modeling Optimization Voltage Index Unified Power Flow Controller Equivalent ...IJMTST Journal
This paper presents an active-reactive power control strategy for voltage source converters (VSCs) based on derivation of the direct and quadrature components of the VSC output current. The proposed method utilizes a multivariable proportional-integral controller and provides almost completely decoupled control capability of the active and reactive power with almost full disturbance rejection due to step changes in the power exchanged between the VSC and the grid. It also imposes fast transient response and zero steady-state error as compared to the conventional power control approaches. The applicability of the proposed power control strategy for providing the robust stability of the system against the uncertainties of the load parameters is also investigated. The superiority of the proposed control strategy over conventional approaches in the new condition of supplying the load is demonstrated. The theoretical aspects of the proposed multivariable-based power control strategy and the conventional approaches are reviewed and simulation results are presented in two separate sections. MATLAB/Simulink 2009a is used to simulate different scenarios of the simulation.
Power Upgrading of Transmission Line by Combining AC DC Transmission and Anal...ijtsrd
This document discusses power upgrading of transmission lines by combining AC-DC transmission and analyzing a Unified Power Flow Controller (UPFC). It begins by introducing the basic concept of designing AC-DC power transmission lines with a single circuit AC line. It then discusses how a UPFC can control various parameters like terminal voltage, series compensation, and phase shift to control power flow. The document presents the design, simulation model, and results of a UPFC model in MATLAB-Simulink. It analyzes how a UPFC can improve voltage profile, reduce line congestion, improve transient stability, and achieve faster steady state conditions. In conclusion, it summarizes that a UPFC is a useful FACTS device for maintaining power system stability
In This paper we present experimental comparative study of feedBack Linearized and Proportional Integral (PI) Controller of the DC bus voltage of three phase shunt Active Power Filter (APF). The FeedBack Linearized and PI controllers are introduced to improve tracking performance characteristics, power quality and minimized consumption of the reactive power. The algorithm used to identify the reference currents is based on the Self Tuning Filter (STF). The firing pulses of the IGBTs inverter are generated using a hysteresis current controller; which is implemented on an analogue card. Finally, the above study, under steady state and transient conditions, is illustrated with signal-flow graphs and corresponding analysis. This study was verified by experimental tests on hardware prototype based on dSPACE-1104. The experimental results show the feasibility and the effectiveness of the designed active filter, associated with Feedback Linearized and PI controllers and are capability in meeting the IEEE 519-1992 recommended harmonic standard limits.
New control strategy for three phase grid-connected lcl inverters without a p...Asoka Technologies
The three-phase synchronous reference frame phase-locked loop (SRF-PLL) is widely used for synchronization applications in power systems. In this paper, a new control strategy for three-phase grid-connected LCL inverters without a PLL is presented. According to the new strategy, a current reference can be generated by using the instantaneous power control scheme and the proposed positive-sequence voltage detector. Through theoretical analysis, it is indicated that a high-quality grid current can be produced by introducing the new control strategy. In addition, a kind of independent control for reactive power can be achieved under unbalanced and distorted grid conditions. Finally, the excellent performance of the proposed control strategy is validated by means of simulation and experimental results.
A Novel Approach for Power Quality Improvement in Distributed Generationseema appa
This document discusses passive filter designs for improving power quality in standalone photovoltaic (PV) systems. It analyzes LC, LCL, and LLCC filter topologies to reduce the total harmonic distortion of a single-phase standalone PV system. Simulation results in MATLAB-SIMULINK show that an LLCC filter is most effective at improving power quality by highly reducing the total harmonic distortion compared to LC and LCL filters. The paper focuses on the design, analysis, and comparison of different passive filter topologies to evaluate their effectiveness in power quality improvement for medium power standalone PV applications.
IRJET- Mitigation of Current and Voltage Harmonics using MAF based UPQCIRJET Journal
This document describes a proposed system for mitigating current and voltage harmonics using a unified power quality conditioner (UPQC) with a moving average filter (MAF)-based control strategy. The UPQC consists of series and shunt compensators to regulate voltage and current, respectively. A photovoltaic array is connected between the compensators and provides power to the system. Simulation results show the system can effectively reduce the total harmonic distortion of both the supply voltage and current, improving power quality delivered to loads despite nonlinearities. The MAF control technique offers optimal harmonic attenuation without reducing controller bandwidth compared to other filtering methods.
Design of Shunt Active Power Filter to eliminate harmonics generated by CFLpaperpublications3
Abstract: The use of non-linear loads; such as TV sets and computer, microwave ovens, multiple low power diode rectifier, fluorescent lamps and electric drives, draw very distorted currents. These non-linear loads lead to generation of current/voltage harmonics and draw reactive power. This paper presents the three-phase shunt active power filter (SAPF) to compensate harmonics generated by non-linear load (compact fluorescent lamp). The instantaneous active and reactive power theory (called p-q theory) is used to design the control of SAPF. The harmonic distortion and the active filter control scheme have been verified by MATLAB simulation.
This document summarizes a research paper that proposes a hybrid selective active filter configuration to mitigate harmonics from an induction furnace. The hybrid filter uses both shunt passive and active filters. PQ theory is used to control the active filter and obtain switching signals. Simulations in MATLAB show the potential of the selective filter to control harmonics. The THD of supply currents is reduced from over 25-37% without the filter to under 2% with the filter. The research demonstrates an effective method for compensating harmonics from an induction furnace load using a hybrid selective active filter controlled by PQ theory.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
A Technique for Shunt Active Filter meld micro grid SystemIJERA Editor
The proposed system presents a control technique for a micro grid connected hybrid generation system ith case study interfaced with a three phase shunt active filter to suppress the current harmonics and reactive power present in the load using PQ Theory with ANN controller. This Hybrid Micro Grid is developed using freely renewable energy resources like Solar Photovoltaic (SPV) and Wind Energy (WE). To extract the maximum available power from PV panels and wind turbines, Maximum power point Tracker (MPPT) has been included. This MPPT uses the “Standard Perturbs and Observe” technique. By using PQ Theory with ANN Controller, the Reference currents are generated which are to be injected by Shunt active power filter (SAPF)to compensate the current harmonics in the non linear load. Simulation studies shows that the proposed control technique performs non-linear load current harmonic compensation maintaining the load current in phase with the source voltage.
IRJET- Enhancement of Power Flow Capability in Power System using UPFC- A RevieWIRJET Journal
This document reviews the use of a Unified Power Flow Controller (UPFC) to enhance power flow capability in power systems. The UPFC is a flexible AC transmission system (FACTS) device that can control both real and reactive power flows on a transmission line. It consists of two voltage source converters connected by a DC link: a static synchronous compensator (STATCOM) and a static synchronous series compensator (SSSC). The STATCOM controls reactive power and the DC link voltage, while the SSSC injects a controlled AC voltage in series with the transmission line to vary the transmission line impedance and power flow. Simulation results show that a UPFC installed on the IEEE 5 bus test system can control power flows and
A CONTROL APPROACH FOR GRID INTERFACING INVERTER IN 3 PHASE 4 WIRE DISTRIBUT...IJMER
With the increase in load demand, the Renewable Energy Sources (RES) are
increasingly connected in the distribution systems which utilizes power electronic
Converters/Inverters. Nowadays, 3-phase 4-wire distribution power system has been widely used in
residential and office buildings, manufacturing facilities, schools etc This paper presents a novel
control strategy for achieving maximum benefits from the grid-interfacing inverters when installed in
3-phase 4-wire distribution systems. The inverter can thus be utilized as: 1) power converter to inject
power to the grid, and 2) shunt APF to compensate current unbalance, load current harmonics and
load neutral current. All of these functions may be accomplished either individually or
simultaneously. This new control concept is demonstrated with extensive MATLAB/Simulink
simulation studies
The document discusses unified power quality conditioners (UPQC) and their use in compensating for power quality issues. Some key points:
1) An UPQC is proposed that uses an artificial neural network controller to compensate for unbalanced grid voltages and load voltages in a power system, correcting issues like voltage sags/swells, power factor correction, and voltage/current harmonic cancellation.
2) The UPQC regulates grid and load voltage unbalances and total harmonic distortion using an artificial neural network controller. In addition to correcting voltage and current disturbances, the controller provides phase detection and grid synchronization.
3) UPQCs are able to compensate for most power quality issues like voltage sags/swells and
Adaptive Fuzzy PID Based Control Strategy For 3Phase 4Wire Shunt Active Filte...IJERA Editor
The document presents a new control strategy for controlling a shunt active power filter to compensate for reactive power and reduce current harmonics in a grid connected to a renewable energy based distribution system. The proposed control strategy uses a fuzzy PID controller to determine the reference compensating currents for a three-phase shunt active power filter. Simulations in MATLAB/Simulink show that the controller has fast dynamic response, accurately tracks the DC voltage reference, and is robust to load parameter variations. The fuzzy PID controller hybridizes classical PID and fuzzy control to exploit the benefits of both.
A New Approach to Powerflow Management in Transmission System Using Interline...IJERA Editor
In this paper a new approach to power flow management in transmission system using interline Power Flow
Controller (IPFC) is proposed and model for IPFC is developed and simulate by MATLAB software. Interline
Power Flow Controller is a versatile device can be used to control power flows of a multi-line system or subnetworks
An Interline Power Flow Controller (IPFC) is a converter based FACTS controller for series
compensation with capability of controlling power flow among multi-lines within the same corridor of the
transmission line. It consists of two or more Voltage Source Converters (VSCs) with a common dc-link. Real
power can be transferred via the common dc-link between the VSCs and each VSC is capable of exchanging
reactive power with its own transmission system
This document summarizes a research paper on microgrid digital twins. It introduces the concept of a microgrid digital twin, which creates a virtual representation of a microgrid that mirrors the behavior of the physical system using real-time data exchange. The paper discusses how microgrid digital twins can be established through modeling physical components and processes, connecting real-time data sources, and continuously updating models. A variety of applications of microgrid digital twins are explored, including design, control, forecasting, fault diagnosis, and resilient operation management. Future trends around increasing data sources, analytics capabilities, and integration of artificial intelligence are also discussed.
Virtual power lines (VPLs) use energy storage systems, such as large batteries, to integrate renewable energy into electric grids and avoid or delay costly infrastructure upgrades. VPLs connect storage at two points - one near renewable generators to store excess power that cannot be transmitted, and another near demand centers to discharge stored power when transmission capacity is limited. This allows renewable power to be transmitted virtually along battery-supported pathways rather than building new wires. VPLs can integrate higher shares of renewable energy faster and more cost-effectively than traditional grid expansions.
More Related Content
Similar to A_New_Way_of_Controlling_Parallel_Connec.pdf
Line and Grid Impedance Impact on the Performances of a Parallel Connected Mo...IAES-IJPEDS
With the rising fuel cost, increasing demand of power and the concerns for global climate change, the use of clean energy make the connection of power electronics building bloc in the heart of the current research. The high output current applications make the parallel connection of modular inverters to be a solution for the use of low power building block inverters where the output power cannot be handled by a single inverter configuration. In this context, average-modeling using average phase–leg technique allows the n-parallel connected inverters to be analyzed accurately and rapidly without requiring the complexity of the full switched inverter topology. The obtained analytical solution along with the equivalent circuit model makes easier the design of the control loop. The analytical solution of the n-parallel connected inverters shows the impact of the line and grid impedance on the performance of the overall system. The impact of this coupling has to be investigated such that the main feature of paralleling inverters is guaranteed and that the inverter mode of operation will not be compromised. The main advantage of paralleling inverters can be lost for a certain coupling impedance considerations.
An Adaptive Virtual Impedance Based Droop Control Scheme for Parallel Inverte...IAES-IJPEDS
This document presents an adaptive virtual impedance based droop control scheme for parallel inverters in a microgrid. The scheme uses an impedance estimator to monitor changes in line impedances between inverters and the point of common coupling. It estimates the line impedance in real time using output voltages and currents of the inverters as well as voltages at the point of common coupling. The estimated line impedance is then fed into a virtual impedance loop to adjust the virtual impedance value and compensate for reactive power mismatches due to changing line impedances, improving power sharing performance. Simulation results show the effectiveness of the proposed adaptive scheme compared to conventional control methods.
A NOVEL TCHNOLOGY FOR HARMONICS AND UNBALANCE COMPENSATION IN ELECTRIC TRACTI...ijiert bestjournal
Power quality problems in power systems have been i mproved due to nonlinear loads. To compensate these problems Direct Power Compensator was proposed in this paper. A Direct Power Compensator (DPC) is proposed in this paper to elim inate the harmonic currents,compensate power factor and voltage unbalance problems created by th e nonlinear loads present in three phase systems. A DPC contains back to back converter by sharing th e same dc link power and v/v transformer to provide a voltage balance in transmission line. Hys teresis harmonic current regulator is used to produce pulse for back to back converter. A control ler maintains the dc-link voltage and compensates the power factor,harmonic currents. A comparative analysis for traction system with and without DPC was performed using MATLAB Simulink . Simulation results show the controller advantages and the applicability of the proposed me thod in railway systems.
IRJET- A Review on Solar based Multilevel Inverter with Three Phase Grid SupplyIRJET Journal
- The document discusses solar-powered multilevel inverters that can supply three-phase grid power. Multilevel inverters have advantages over single-level inverters like lower harmonic distortion, reduced electromagnetic interference, and the ability to operate at several voltage levels.
- The literature review covers prior research on different multilevel inverter topologies for photovoltaic systems, including the flying capacitor, neutral point clamped, and cascaded H-bridge inverters. It also discusses control methods like maximum power point tracking and modulation techniques.
- The goal is to develop a multilevel inverter powered by PV panels that can supply three-phase grid power with minimum harmonic distortion and reduced component requirements compared to
Mitigation of the Harmonics under Reactive Power Compensation by SHPF-TCR Usi...IJERA Editor
In this paper, a combined system of a thyristor-controlled reactor (TCR) and a shunt hybrid power filter
(SHPF)has been designed by MATLAB/SIMULINK approach for harmonic and reactive power compensation.
The quality of the power is effected by many factors like harmonic contamination, due to the increment of nonlinear
loads, sag and swell due to the switching of the loads etc. Also control schemes based on PI and Fuzzy
logic controllers have been proposed to mitigate the harmonics and neutral current . The proposed methodology
not only reduces the complexity but also offers simplicity to implement and increases reliability of the system.
These control strategies also help in achieving a low cost highly effective control. The performance is also
observed under influence of utility side disturbances such as harmonics, flicker and spikes with Non-Linear and
Reactive Loads with different control strategies.
Modeling Optimization Voltage Index Unified Power Flow Controller Equivalent ...IJMTST Journal
This paper presents an active-reactive power control strategy for voltage source converters (VSCs) based on derivation of the direct and quadrature components of the VSC output current. The proposed method utilizes a multivariable proportional-integral controller and provides almost completely decoupled control capability of the active and reactive power with almost full disturbance rejection due to step changes in the power exchanged between the VSC and the grid. It also imposes fast transient response and zero steady-state error as compared to the conventional power control approaches. The applicability of the proposed power control strategy for providing the robust stability of the system against the uncertainties of the load parameters is also investigated. The superiority of the proposed control strategy over conventional approaches in the new condition of supplying the load is demonstrated. The theoretical aspects of the proposed multivariable-based power control strategy and the conventional approaches are reviewed and simulation results are presented in two separate sections. MATLAB/Simulink 2009a is used to simulate different scenarios of the simulation.
Power Upgrading of Transmission Line by Combining AC DC Transmission and Anal...ijtsrd
This document discusses power upgrading of transmission lines by combining AC-DC transmission and analyzing a Unified Power Flow Controller (UPFC). It begins by introducing the basic concept of designing AC-DC power transmission lines with a single circuit AC line. It then discusses how a UPFC can control various parameters like terminal voltage, series compensation, and phase shift to control power flow. The document presents the design, simulation model, and results of a UPFC model in MATLAB-Simulink. It analyzes how a UPFC can improve voltage profile, reduce line congestion, improve transient stability, and achieve faster steady state conditions. In conclusion, it summarizes that a UPFC is a useful FACTS device for maintaining power system stability
In This paper we present experimental comparative study of feedBack Linearized and Proportional Integral (PI) Controller of the DC bus voltage of three phase shunt Active Power Filter (APF). The FeedBack Linearized and PI controllers are introduced to improve tracking performance characteristics, power quality and minimized consumption of the reactive power. The algorithm used to identify the reference currents is based on the Self Tuning Filter (STF). The firing pulses of the IGBTs inverter are generated using a hysteresis current controller; which is implemented on an analogue card. Finally, the above study, under steady state and transient conditions, is illustrated with signal-flow graphs and corresponding analysis. This study was verified by experimental tests on hardware prototype based on dSPACE-1104. The experimental results show the feasibility and the effectiveness of the designed active filter, associated with Feedback Linearized and PI controllers and are capability in meeting the IEEE 519-1992 recommended harmonic standard limits.
New control strategy for three phase grid-connected lcl inverters without a p...Asoka Technologies
The three-phase synchronous reference frame phase-locked loop (SRF-PLL) is widely used for synchronization applications in power systems. In this paper, a new control strategy for three-phase grid-connected LCL inverters without a PLL is presented. According to the new strategy, a current reference can be generated by using the instantaneous power control scheme and the proposed positive-sequence voltage detector. Through theoretical analysis, it is indicated that a high-quality grid current can be produced by introducing the new control strategy. In addition, a kind of independent control for reactive power can be achieved under unbalanced and distorted grid conditions. Finally, the excellent performance of the proposed control strategy is validated by means of simulation and experimental results.
A Novel Approach for Power Quality Improvement in Distributed Generationseema appa
This document discusses passive filter designs for improving power quality in standalone photovoltaic (PV) systems. It analyzes LC, LCL, and LLCC filter topologies to reduce the total harmonic distortion of a single-phase standalone PV system. Simulation results in MATLAB-SIMULINK show that an LLCC filter is most effective at improving power quality by highly reducing the total harmonic distortion compared to LC and LCL filters. The paper focuses on the design, analysis, and comparison of different passive filter topologies to evaluate their effectiveness in power quality improvement for medium power standalone PV applications.
IRJET- Mitigation of Current and Voltage Harmonics using MAF based UPQCIRJET Journal
This document describes a proposed system for mitigating current and voltage harmonics using a unified power quality conditioner (UPQC) with a moving average filter (MAF)-based control strategy. The UPQC consists of series and shunt compensators to regulate voltage and current, respectively. A photovoltaic array is connected between the compensators and provides power to the system. Simulation results show the system can effectively reduce the total harmonic distortion of both the supply voltage and current, improving power quality delivered to loads despite nonlinearities. The MAF control technique offers optimal harmonic attenuation without reducing controller bandwidth compared to other filtering methods.
Design of Shunt Active Power Filter to eliminate harmonics generated by CFLpaperpublications3
Abstract: The use of non-linear loads; such as TV sets and computer, microwave ovens, multiple low power diode rectifier, fluorescent lamps and electric drives, draw very distorted currents. These non-linear loads lead to generation of current/voltage harmonics and draw reactive power. This paper presents the three-phase shunt active power filter (SAPF) to compensate harmonics generated by non-linear load (compact fluorescent lamp). The instantaneous active and reactive power theory (called p-q theory) is used to design the control of SAPF. The harmonic distortion and the active filter control scheme have been verified by MATLAB simulation.
This document summarizes a research paper that proposes a hybrid selective active filter configuration to mitigate harmonics from an induction furnace. The hybrid filter uses both shunt passive and active filters. PQ theory is used to control the active filter and obtain switching signals. Simulations in MATLAB show the potential of the selective filter to control harmonics. The THD of supply currents is reduced from over 25-37% without the filter to under 2% with the filter. The research demonstrates an effective method for compensating harmonics from an induction furnace load using a hybrid selective active filter controlled by PQ theory.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
A Technique for Shunt Active Filter meld micro grid SystemIJERA Editor
The proposed system presents a control technique for a micro grid connected hybrid generation system ith case study interfaced with a three phase shunt active filter to suppress the current harmonics and reactive power present in the load using PQ Theory with ANN controller. This Hybrid Micro Grid is developed using freely renewable energy resources like Solar Photovoltaic (SPV) and Wind Energy (WE). To extract the maximum available power from PV panels and wind turbines, Maximum power point Tracker (MPPT) has been included. This MPPT uses the “Standard Perturbs and Observe” technique. By using PQ Theory with ANN Controller, the Reference currents are generated which are to be injected by Shunt active power filter (SAPF)to compensate the current harmonics in the non linear load. Simulation studies shows that the proposed control technique performs non-linear load current harmonic compensation maintaining the load current in phase with the source voltage.
IRJET- Enhancement of Power Flow Capability in Power System using UPFC- A RevieWIRJET Journal
This document reviews the use of a Unified Power Flow Controller (UPFC) to enhance power flow capability in power systems. The UPFC is a flexible AC transmission system (FACTS) device that can control both real and reactive power flows on a transmission line. It consists of two voltage source converters connected by a DC link: a static synchronous compensator (STATCOM) and a static synchronous series compensator (SSSC). The STATCOM controls reactive power and the DC link voltage, while the SSSC injects a controlled AC voltage in series with the transmission line to vary the transmission line impedance and power flow. Simulation results show that a UPFC installed on the IEEE 5 bus test system can control power flows and
A CONTROL APPROACH FOR GRID INTERFACING INVERTER IN 3 PHASE 4 WIRE DISTRIBUT...IJMER
With the increase in load demand, the Renewable Energy Sources (RES) are
increasingly connected in the distribution systems which utilizes power electronic
Converters/Inverters. Nowadays, 3-phase 4-wire distribution power system has been widely used in
residential and office buildings, manufacturing facilities, schools etc This paper presents a novel
control strategy for achieving maximum benefits from the grid-interfacing inverters when installed in
3-phase 4-wire distribution systems. The inverter can thus be utilized as: 1) power converter to inject
power to the grid, and 2) shunt APF to compensate current unbalance, load current harmonics and
load neutral current. All of these functions may be accomplished either individually or
simultaneously. This new control concept is demonstrated with extensive MATLAB/Simulink
simulation studies
The document discusses unified power quality conditioners (UPQC) and their use in compensating for power quality issues. Some key points:
1) An UPQC is proposed that uses an artificial neural network controller to compensate for unbalanced grid voltages and load voltages in a power system, correcting issues like voltage sags/swells, power factor correction, and voltage/current harmonic cancellation.
2) The UPQC regulates grid and load voltage unbalances and total harmonic distortion using an artificial neural network controller. In addition to correcting voltage and current disturbances, the controller provides phase detection and grid synchronization.
3) UPQCs are able to compensate for most power quality issues like voltage sags/swells and
Adaptive Fuzzy PID Based Control Strategy For 3Phase 4Wire Shunt Active Filte...IJERA Editor
The document presents a new control strategy for controlling a shunt active power filter to compensate for reactive power and reduce current harmonics in a grid connected to a renewable energy based distribution system. The proposed control strategy uses a fuzzy PID controller to determine the reference compensating currents for a three-phase shunt active power filter. Simulations in MATLAB/Simulink show that the controller has fast dynamic response, accurately tracks the DC voltage reference, and is robust to load parameter variations. The fuzzy PID controller hybridizes classical PID and fuzzy control to exploit the benefits of both.
A New Approach to Powerflow Management in Transmission System Using Interline...IJERA Editor
In this paper a new approach to power flow management in transmission system using interline Power Flow
Controller (IPFC) is proposed and model for IPFC is developed and simulate by MATLAB software. Interline
Power Flow Controller is a versatile device can be used to control power flows of a multi-line system or subnetworks
An Interline Power Flow Controller (IPFC) is a converter based FACTS controller for series
compensation with capability of controlling power flow among multi-lines within the same corridor of the
transmission line. It consists of two or more Voltage Source Converters (VSCs) with a common dc-link. Real
power can be transferred via the common dc-link between the VSCs and each VSC is capable of exchanging
reactive power with its own transmission system
Similar to A_New_Way_of_Controlling_Parallel_Connec.pdf (20)
This document summarizes a research paper on microgrid digital twins. It introduces the concept of a microgrid digital twin, which creates a virtual representation of a microgrid that mirrors the behavior of the physical system using real-time data exchange. The paper discusses how microgrid digital twins can be established through modeling physical components and processes, connecting real-time data sources, and continuously updating models. A variety of applications of microgrid digital twins are explored, including design, control, forecasting, fault diagnosis, and resilient operation management. Future trends around increasing data sources, analytics capabilities, and integration of artificial intelligence are also discussed.
Virtual power lines (VPLs) use energy storage systems, such as large batteries, to integrate renewable energy into electric grids and avoid or delay costly infrastructure upgrades. VPLs connect storage at two points - one near renewable generators to store excess power that cannot be transmitted, and another near demand centers to discharge stored power when transmission capacity is limited. This allows renewable power to be transmitted virtually along battery-supported pathways rather than building new wires. VPLs can integrate higher shares of renewable energy faster and more cost-effectively than traditional grid expansions.
This document presents the development of a microgrid central controller and hierarchical control system in the Intelligent Microgrid Lab at Aalborg University. The lab contains several inverter-based microgrid setups that can operate independently or be interconnected. Local primary control is implemented on dSPACE controllers while a LabVIEW-based central controller coordinates secondary and tertiary control functions. An example case of voltage/frequency restoration and voltage unbalance compensation is tested using hierarchical control across the different levels. Experimental results demonstrate the performance of the overall control system.
This document summarizes ongoing research in applying intelligent methods to microgrid design, modeling, simulation and control. It discusses several ongoing research projects:
1) A decentralized multi-agent system for microgrid operation being developed at Michigan State University that uses a three-step communication algorithm for distributed control of distributed generators and loads.
2) A distributed incremental cost consensus algorithm for economic dispatch being developed at North Carolina State University that allows distributed controllers to allocate power among connected buses.
3) A system developed at the University of North Carolina at Charlotte that models and controls a photovoltaic and fuel cell hybrid microgrid using a neurocontroller-based intelligent system centric controller.
4) A multi-agent based load restoration
The document presents a novel approach for implementing secondary control in droop-controlled microgrids in a distributed manner rather than through a central microgrid controller. The proposed distributed secondary control approach is able to restore frequency and voltage deviations in the microgrid while also ensuring accurate reactive power sharing between distributed generation units. Experimental results demonstrate the feasibility of the distributed secondary control approach. Communication latency and data dropouts are also studied to evaluate the impact on the control system performance.
- The document discusses thyristors, which are four-layer semiconductor devices that can act as bidirectional switches when triggered.
- It focuses on the silicon controlled rectifier (SCR) and triac, explaining their structure and operating characteristics. The SCR can only conduct current in one direction while the triac can conduct bi-directionally.
- Key aspects of thyristor operation are described, including triggering, turn-on, turn-off behavior, and applications in switching circuits. Limitations of the SCR for alternating current applications are also reviewed.
This document defines an IEEE 2030.5 profile for implementing SAE J3072 to enable electric vehicles to discharge power to the electric grid via vehicle-to-grid (V2G) technology. It specifies requirements for communications between electric vehicle supply equipment (EVSE) and plug-in electric vehicles (PEVs) to enable authorization and control of discharging according to IEEE and SAE standards. The profile is intended to guide developers in achieving interoperable V2G communications using the IEEE 2030.5 protocol.
This document describes developing a dynamic model for a reduced 240-bus Western Electricity Coordinating Council (WECC) system model to enable integrated scheduling and dynamic simulations of high renewable energy penetration. The generation resource mix of the model was updated based on 2018 data to reflect a 20% share of inverter-based resources like solar and wind power. Generic dynamic models were used for generators and governors. The system inertia was distributed to match WECC planning cases. The dynamic model was validated against recorded frequency event measurements and preserves the dominant inter-area oscillation mode in WECC.
The document specifies the SunSpec Device Information Model, which defines a standardized structure for specifying and exchanging device data. It defines elements like models, points, point groups, and symbols to structure device information. It also specifies encoding of model definitions and instances using JSON and CSV formats, and usage of models with Modbus and JSON interfaces.
Virtual power lines (VPLs) use energy storage systems, such as large batteries, to integrate renewable energy into electric grids and avoid or delay costly infrastructure upgrades. VPLs connect storage at two points - one near renewable generators to store excess power that cannot be transmitted, and another near demand centers to discharge stored power when transmission capacity is limited. This allows renewable power to be transmitted virtually along battery-supported pathways instead of building new wires. VPLs can integrate higher shares of renewable energy faster and more flexibly than traditional grid expansion.
This document provides an overview of a buck-boost DC-DC converter design with an input protection system. It describes the objectives, requirements, functional decomposition, planning, previous design discussions, LT3791-1 controller component selection, operation discussion, initial and final design iterations, PCB design and assembly, input protection circuit design, and hardware testing. The goals are to design a buck-boost converter capable of harvesting energy from exercise machines that meets specifications for input voltage range, output voltage, efficiency, and includes overvoltage and undervoltage protection.
E BOOK Electric Power Transformer Engineering.pdfRafikCherni
This document provides information about electric power transformers and discusses copyright and permission issues. It contains three main sections. The first section notes that the book contains information from reputable sources and lists references, but does not guarantee the validity of all materials. The second section states that no part of the book can be reproduced without permission. The third section provides copyright and permission details for material reprinted from IEEE publications.
This document discusses cable monitoring solutions using distributed temperature sensing (DTS) technology to prevent cable failures and optimize power networks. It provides an overview of issues like overheating of buried cables, describes DTS principles and thermal modeling, presents a case study on monitoring a buried cable, discusses further applications like subsea cables and cable tunnels, emphasizes the importance of measurement speed, and introduces Sensornet's DTS product range for cable monitoring.
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive function. Exercise causes chemical changes in the brain that may help protect against developing mental illness and improve symptoms for those who already suffer from conditions like anxiety and depression.
1. Power transformer losses are economically and environmentally significant, leading to new regulations requiring more accurate measurement of losses.
2. Transformer Loss Measurement Systems (TLMS) must be calibrated to provide proven, validated accuracy of less than 3% at a power factor of 0.01 to reliably measure losses within the tight limits.
3. The ELPOW project aims to develop a calibration system for TLMS with uncertainties below 0.5% at a power factor of 0.01 through simultaneous voltage and current generation and phase locking the current to the externally applied voltage, showing promising initial results with uncertainties below 0.3%.
Introduction- e - waste – definition - sources of e-waste– hazardous substances in e-waste - effects of e-waste on environment and human health- need for e-waste management– e-waste handling rules - waste minimization techniques for managing e-waste – recycling of e-waste - disposal treatment methods of e- waste – mechanism of extraction of precious metal from leaching solution-global Scenario of E-waste – E-waste in India- case studies.
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressionsVictor Morales
K8sGPT is a tool that analyzes and diagnoses Kubernetes clusters. This presentation was used to share the requirements and dependencies to deploy K8sGPT in a local environment.
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...IJECEIAES
Climate change's impact on the planet forced the United Nations and governments to promote green energies and electric transportation. The deployments of photovoltaic (PV) and electric vehicle (EV) systems gained stronger momentum due to their numerous advantages over fossil fuel types. The advantages go beyond sustainability to reach financial support and stability. The work in this paper introduces the hybrid system between PV and EV to support industrial and commercial plants. This paper covers the theoretical framework of the proposed hybrid system including the required equation to complete the cost analysis when PV and EV are present. In addition, the proposed design diagram which sets the priorities and requirements of the system is presented. The proposed approach allows setup to advance their power stability, especially during power outages. The presented information supports researchers and plant owners to complete the necessary analysis while promoting the deployment of clean energy. The result of a case study that represents a dairy milk farmer supports the theoretical works and highlights its advanced benefits to existing plants. The short return on investment of the proposed approach supports the paper's novelty approach for the sustainable electrical system. In addition, the proposed system allows for an isolated power setup without the need for a transmission line which enhances the safety of the electrical network
Batteries -Introduction – Types of Batteries – discharging and charging of battery - characteristics of battery –battery rating- various tests on battery- – Primary battery: silver button cell- Secondary battery :Ni-Cd battery-modern battery: lithium ion battery-maintenance of batteries-choices of batteries for electric vehicle applications.
Fuel Cells: Introduction- importance and classification of fuel cells - description, principle, components, applications of fuel cells: H2-O2 fuel cell, alkaline fuel cell, molten carbonate fuel cell and direct methanol fuel cells.
artificial intelligence and data science contents.pptxGauravCar
What is artificial intelligence? Artificial intelligence is the ability of a computer or computer-controlled robot to perform tasks that are commonly associated with the intellectual processes characteristic of humans, such as the ability to reason.
› ...
Artificial intelligence (AI) | Definitio
The CBC machine is a common diagnostic tool used by doctors to measure a patient's red blood cell count, white blood cell count and platelet count. The machine uses a small sample of the patient's blood, which is then placed into special tubes and analyzed. The results of the analysis are then displayed on a screen for the doctor to review. The CBC machine is an important tool for diagnosing various conditions, such as anemia, infection and leukemia. It can also help to monitor a patient's response to treatment.
1. See discussions, stats, and author profiles for this publication at: https://www.researchgate.net/publication/281309684
A New Way of Controlling Parallel-Connected
Inverters by Using Synchronous Reference
Frame Virtual Impedance Loop – Part I: Control
Principle
ARTICLE in IEEE TRANSACTIONS ON POWER ELECTRONICS · JANUARY 2015
Impact Factor: 6.01 · DOI: 10.1109/TPEL.2015.2472279
READS
86
5 AUTHORS, INCLUDING:
Yajuan Guan
Aalborg University
9 PUBLICATIONS 17 CITATIONS
SEE PROFILE
Josep M. Guerrero
Aalborg University
378 PUBLICATIONS 7,166 CITATIONS
SEE PROFILE
Xin Zhao
Aalborg University
6 PUBLICATIONS 4 CITATIONS
SEE PROFILE
J.C. Vasquez
Aalborg University
124 PUBLICATIONS 2,444 CITATIONS
SEE PROFILE
All in-text references underlined in blue are linked to publications on ResearchGate,
letting you access and read them immediately.
Available from: Josep M. Guerrero
Retrieved on: 03 February 2016
2. Aalborg Universitet
A New Way of Controlling Parallel-Connected Inverters by Using Synchronous
Reference Frame Virtual Impedance Loop – Part I: Control Principle
Guan, Yajuan; Guerrero, Josep M.; Zhao, Xin; Quintero, Juan Carlos Vasquez; Guo,
Xiaoqiang
Published in:
I E E E Transactions on Power Electronics
DOI (link to publication from Publisher):
10.1109/TPEL.2015.2472279
Publication date:
2015
Link to publication from Aalborg University
Citation for published version (APA):
Guan, Y., Guerrero, J. M., Zhao, X., Quintero, J. C. V., & Guo, X. (2015). A New Way of Controlling Parallel-
Connected Inverters by Using Synchronous Reference Frame Virtual Impedance Loop – Part I: Control
Principle. I E E E Transactions on Power Electronics. 10.1109/TPEL.2015.2472279
General rights
Copyright and moral rights for the publications made accessible in the public portal are retained by the authors and/or other copyright owners
and it is a condition of accessing publications that users recognise and abide by the legal requirements associated with these rights.
? Users may download and print one copy of any publication from the public portal for the purpose of private study or research.
? You may not further distribute the material or use it for any profit-making activity or commercial gain
? You may freely distribute the URL identifying the publication in the public portal ?
Take down policy
If you believe that this document breaches copyright please contact us at vbn@aub.aau.dk providing details, and we will remove access to
the work immediately and investigate your claim.
Downloaded from vbn.aau.dk on: september 05, 2015
3. TPEL-Reg-2015-03-0479 1
Abstract—A novel simple and effective autonomous
current-sharing controller for parallel three-phase inverters is
proposed in this paper. The proposed controller provides faster
response and better accuracy in contrast to the conventional
droop control, since this novel approach does not require any
active or reactive power calculations. Instead, a
synchronous-reference-frame (SRF) virtual impedance loop and
an SRF-based phase-locked loop are used. Stationary analysis is
provided in order to identify the inherent mechanism of the direct
and quadrature output currents in relation to the voltage
amplitude and frequency with different line impedances by means
of the system transfer functions. Comparison experiments from
two parallel inverters are presented to compare the control
performance of the conventional droop control and the proposed
control with different line impedances. In addition, experimental
results from a setup with three parallel 2.2 kW inverters verify the
effectiveness of the proposed control strategy in different
scenarios.
Index Terms—Parallel inverters, synchronous reference frame,
phase-locked loop, virtual impedance, droop control.
I. INTRODUCTION
ROOP control method has been widely used in the last
decade as the decentralized control of parallel converters
in several applications such as parallel redundant
uninterruptible power supplies (UPS) to avoid critical
communication among units, distributed power systems,
microgrids (MGs), and so forth [1]-[12]. This well-known
control technique aims to proportionally share active and
reactive powers which adjusting frequency and output voltage
amplitudes of each inverter locally in order to emulate the
behavior of a synchronous generator [3]. Although this
technique only requires local information, it presents a number
Yajuan Guan, Josep M. Guerrero, Xin Zhao and Juan C. Vasquez are with
Department of Energy Technology, Aalborg University, 9220 Aalborg,
Denmark (e-mail: ygu@et.aau.dk, joz@et.aau.dk, xzh@et.aau.dk,
juq@et.aau.dk).
Xiaoqiang. Guo, is with the Key Lab of Power Electronics for Energy
Conservation and Motor drive of Hebei province, Department of Electrical
Engineering, Yanshan University, Qinhuangdao 066004, China (e-mail:
gxq@ysu.edu.cn)
of stability issues that have been solved along the literature
[4]-[7].
One of the main problems is that the droop coefficients
which regulate frequency and amplitudes are basically
proportional terms, so that in order to increase their range of
values for improving system dynamics, derivative terms were
added [13]-[16]. Unlike the conventional droop controllers
which yield 1- dimension of freedom (DOF) tunable control,
the improved droop controllers yield 2-DOF tunable control.
Subsequently, the dynamic performance of the system can be
adjusted to damp the oscillatory behavior of the power sharing
controllers without affecting the static droop gains.
Another issue with regards to conventional droop is that the
frequency and voltage are respectively related to active and
reactive power when the output impedance of the generator is
mainly inductive, e.g. induction generators. Hence, by using the
droop method, the power sharing performance is affected by
the output impedance of the distributed generation (DG) units
and the line impedances. However, the output impedance can
be fixed by means of a fast control loop named virtual
impedance in an inverter [17], [18]. In this sense, the output
impedance can be treated as another control loop which
enforces the inverter to behave in accordance to the
inductance-to-resistance ratio (X/R) line impedance, e.g.
mainly resistive in case of low voltage networks [19].
In case of resistive lines and/or virtual impedances, the active
power is controlled by the inverter voltage amplitude, while the
reactive power flow is dominated by the angle, so that it can be
controlled by the frequency of the system [20]-[24]. In this
sense, the active power-voltage (P-V) droop control needs to be
used instead of the conventional active power-frequency (P-f)
droop control, which is contrary to the conventional electrical
transmission systems or induction generation dominated
systems.
Several control methodologies with different
implementations for conventional droop controller have been
also proposed [25]-[28]. A Q – V dot droop control method is
mostly used to improve reactive power sharing [29].
Based on the abovementioned issues, a control architecture
based on a virtual resistance, P-V and Q-f droops is used for
dealing with the autonomous operation of parallel connected
inverters [20], [30]. However, this approach has the inherent
drawback that it needs to calculate instantaneous active and
A New Way of Controlling Parallel-Connected
Inverters by Using Synchronous Reference
Frame Virtual Impedance Loop
– Part I: Control Principle
Yajuan Guan, Student, IEEE, Josep M. Guerrero, Fellow, IEEE, Xin Zhao, Juan C. Vasquez, Senior
Member IEEE, Xiaoqiang Guo, Senior Member, IEEE
D
4. TPEL-Reg-2015-03-0479 2
reactive powers and then average them through low-pass filters
(LPF) whose bandwidth deteriorate the system transient
response [15]. Even in three phase systems that the active and
reactive power can be calculated by using the instantaneous
power theory, a post-filter processing is necessary in order to
completely remove the distorted power components [31].
Furthermore, in a practical situation, the load sharing
performance of the conventional droop control is degraded
when short lines with small impedance are used, especially in
low voltage networks. In this case, a small deviation in voltage
frequency and amplitude will result in large power oscillation
and even instabilities [32]. The drawbacks of droop control can
be summarized as listed below:
• Slow dynamic response: Since it requires LPFs with
reduced bandwidth to calculate the average values of
the active and reactive powers both in islanded and
grid-connected modes.
• Active/reactive power coupling.
• Slow responses when active/reactive power sharing
ratios are suddenly changed.
• Performance is serious affected by the line impedance.
• Complex design.
• The power sharing could be degraded if the sum of the
output impedance and the line impedance is
unbalanced.
Another possible solution is the combination of current
sharing control and power droop control techniques. A
voltage-power droop/frequency-reactive power boost
(VPD/FQB) control scheme which allows multiple voltage
source converters (VSCs) to operate in parallel in MGs and to
share a common load power in proportion to a predetermined
ration is presented in [33], [34]. In [33], an additional virtual
resistance loop is necessary since the inverter output impedance
cannot be equal to zero due to the PI controller in voltage
control loop. A decentralized control for redundant parallel
connection of multiple UPS using only current sensors is
proposed [35], [36]. The active and reactive components of
output current are used instead of active and reactive power to
mimic the droop control, while the LPFs are still necessary. A
novel piecewise linear V-I droop controller has been proposed
to exploit the flexibility and fast dynamics of the inverter-based
distributed energy resources [37], however a global positioning
system (GPS) signal as the communication is used to
synchronize each DG unit and allow for constant frequency
operation. A voltage and frequency droop control based on
mixed voltage and current source concept and finite output
impedance emulation for single phase inverter based low
voltage grid has been proposed [22], [38]. This method can
provide not only wireless parallel operation control, but also
has the capability of mitigation of voltage harmonics and
short-circuit behavior as it takes the R to X line impedance ratio
into account. However, this control approach is complex, since
a Kalman filter estimator and a linear quadratic regulator are
required.
To cope with all the aforementioned, a simpler and faster
controller is proposed in this paper, which consists of a
synchronous-reference-frame (SRF) virtual impedance loop, an
SFR phase-locked loop (PLL) and a proportional-resonant (PR)
controller in voltage control loop. The proposed control
strategy provides both instantaneous current sharing and fast
dynamic response for paralleled voltage controlled inverters
(VCIs). The virtual resistance loop which contains a d-axis
virtual resistance loop and a q-axis virtual resistance loop is
used to achieve direct and quadrature load currents sharing
separately among three-phase inverters. The concept is derived
from the current-sharing control schemes already used in dc
paralleled converters [39]-[42]. In contrast with the
conventional droop control, there is no need to calculate
active/reactive powers. An additional PLL is needed to adjust
the phase of the voltage reference and ensure the
synchronization among the paralleled VCIs. The paper is
organized as follows. Section II reviews the conventional droop
control principle. Section III analyzes the current flow when
virtual resistive impedance in the stationary reference frame is
used. Section IV introduces the proposed control structure and
the control principle. Section V presents the inherent droop
characteristic and coupling analysis of the proposed control
with different line impedances. Experimental results are shown
in Section VI in order to evaluate the feasibility of the proposed
approach and to compare the control performance with the
conventional droop control. Section VII concludes the paper.
Finally, the appendix provides the derivative process of the
mathematic equations. This paper is the first part of a two-part
paper focusing on the control principle and steady state
performance analysis. The second part of this paper deals with
the small-signal state-space models and stability analysis of the
proposed parallel-VCI-based system.
II.REVIEW OF THE DROOP CONTROL PRINCIPLE
Fig. 1 shows the equivalent circuit of a two-paralleled
inverter system including generated voltages ( and ),
output impedances ( and ), virtual impedances ( 1
vir
Z
→
and 2
vir
Z
→
), output voltage ( and ) and line impedances (
and ) of each inverter. It can be considered as a
subset of distributed power network operating in autonomous
islanded mode.
The phase differences between the output voltage (ϕ gn) and
the point of common coupling (PCC) voltage (ϕ bus), as well as
the amplitude of equivalent impedance ( ), which
consists of inverter output impedance ( ), line
impedance ( ), and virtual impedance ( virn virn
Z ϕ
∠ ),
are considered in this study. The active and reactive power
output can be derived as:
2
cos cos( )
gn n gn bus gn bus n
n
n
V V V
P
Z
ϕ ϕ ϕ ϕ
− − +
= (1)
2
sin sin( )
gn n gn bus gn bus n
n
n
V V V
Q
Z
ϕ ϕ ϕ ϕ
− − +
= (2)
In traditional power systems, the equivalent impedances
between the paralleled inverters present high X/R ratio. The
1
g
V
→
2
g
V
→
1
o
Z
→
2
o
Z
→
1
o
V
→
2
o
V
→
1
line
Z
→
2
line
Z
→
n n
Z ϕ
∠
on oZn
Z ϕ
∠
linen linen
Z ϕ
∠
5. TPEL-Reg-2015-03-0479 3
1
g
V
→ 1
vir
Z
→
2
vir
Z
→
0
bus
V ∠
1
o
I
→
2
o
I
→
1
line
Z
→
2
g
V
→
1
o
Z
→
2
o
Z
→
2
line
Z
→
1
o
V
→
2
o
V
→
load
Z
→
Fig. 1. Equivalent circuit of a parallel inverter system with virtual resistances.
active power ( ) can be adjusted with the voltage angle (ϕ gn),
and reactive power ( ) can be regulated with voltage
amplitude (Vgn) separately. Based on this power flow analysis,
the droop control law can be expressed as:
(3)
(4)
where and are the normal angular frequency and output
voltage amplitude, respectively, and are the droop
coefficients.
However, the load sharing performance of the conventional
droop control is degraded in a practical situation when using
short lines with small impedances, especially in low voltage
networks. Output power ( and ), output voltage
amplitude and frequency are coupled, because
[ ]
sin( ) / ( ) /
on bus n on bus n
Z Z
ϕ ϕ ϕ ϕ
− ≈ − cannot be neglected
when 0
n bus
ϕ ϕ
− ≠ or n
Z is too small, that may result in
imprecise power control. Furthermore, the stability problems
would arise for conventional droop controlled systems with
small equivalent line impedance , since small frequency or
voltage amplitude deviations can result in large power
oscillations.
III. CURRENT FLOW ANALYSIS
Each inverter in Fig.1 can be modeled by a two-terminal
Thévenin equivalent circuit in Laplace as follows:
[ ]
(s) (s) (s) (s) (s) (s) (s)
bus n refn on linen virn on
V G V Z Z Z I
= − + + (5)
where (s)
refn
V is the output voltage reference; ( )
n
G s is the
voltage gain. The inner current and voltage loops are
responsible for minimizing ( )
on
Z s , i. e. by using a proportional
+ resonant (PR) controller tuned at the line frequency. In this
sense, ( )
on
Z s is approximately equal to zero, whereas (s)
n
G is
equal to 1 at the resonant frequency of PR controller.
Considering that ( )
linen
Z s is practically very small in low
scale systems such as low voltage MGs, (s)
virn
Z becomes the
predominant component. Thus, (5) can be simplified as:
(s) (s) (s) (s) (s)
bus n refn virn on
V G V Z I
= − (6)
When only virtual resistance is adopted, an equivalent
Thévenin circuit can present the closed loop inverter, as
(s) (s)
n refn
G V
virn
R (s)
on
I
(s)
bus
V
Fig. 2. Equivalent Thévenin circuit of closed-loop inverter.
2
θ
1
θ
2 2
oq virq
I R
1 1
oq virq
I R
2 2
od vird
I R 1 1
od vird
I R
q
d
2
V
→
Δ
1
V
→
Δ
Fig. 3. Vector diagram of the concept.
illustrated in Fig. 2. The voltage difference between the
generated voltage and common bus voltage at the line
frequency can be expressed in dq reference frame as follows:
refn bus odn virdn oqn virqn
V V I R jI R
→ →
− = + (7)
where odn
I and oqn
I are the d and q-axis components of output
current, respectively.
In this case, because the voltage reference phasor ( ref
V
→
) and
common bus voltage phasor ( bus
V
→
) are identical for each DG
unit, the different values of vird
R and virq
R will result in
different voltage drop that will cause different current output
vectors ( ), as shown in Fig. 3. The relationship of od
I , oq
I ,
vird
R and virq
R can be generalized and expressed for number N
of converters as follows:
(8a)
(8b)
The d- and q-axis output currents od
I and oq
I of the
paralleled inverters are inversely proportional to the
corresponding virtual resistances. Therefore, the direct and
quadrature currents output of each inverter can be regulated
independently by adjusting the virtual impedances based on
different power rates, commands from energy management
system (EMS) or other superior control loops.
Furthermore, the active and reactive power output sharing
strategy among the paralleled inverters can be obtained from (8)
by multiplying the voltage reference. Hence, considering that
the voltage references (Vref) of each inverter are equal, the
active and reactive power output will also be properly shared
based on the virtual resistances, as shown in (9):
1 1 2 2
o vird o vird oN virdN
P R P R P R
= = =
… (9a)
1 1 2 2
o virq o virq oN virqN
Q R Q R Q R
= = =
… (9b)
n
P
n
Q
* *
( )
n n p n n
k P P
ω
ω ω
= + −
* *
( )
n n qV n n
V V k Q Q
= + −
*
n
ω *
n
V
p
k ω qV
k
n
P n
Q
n
Z
o
I
→
1 1 2 2 ...
od vird od vird odN virdN
I R I R I R
= = =
1 1 2 2 ...
oq virq oq virq oqN virqN
I R I R I R
= = =
6. TPEL-Reg-2015-03-0479 4
where on
P and on
Q are the active and reactive power output of
inverter #n.
IV. PROPOSED AUTONOMOUS CURRENT-SHARING
CONTROLLER
Follow the above analysis, a simpler and faster controller is
proposed in this paper. The novel control strategy is shown in
Fig. 4(b). Compared with the improved droop controller in Fig.
4(a), the droop controller could be replaced by a novel
controller which comprises of an SRF-PLL and a virtual
resistance loop in SRF.
A. Configuration of the proposed controller
The power stage consists of a three-leg three-phase inverter
connected to a DC link, loaded by an Lf-Cf filter, and connected
to the AC bus through a power line (Zline). Indeed, the proposed
control strategy can also be extended to single-phase systems.
The main difference between the single-phase systems and
three-phase systems is that the orthogonal voltage system in
single-phase systems needs to be generated by an extra control
loop [43], [44].
The controller including an SRF-PLL, a virtual resistance
loop (Rvird and Rvirq), a DC link voltage feed-forward loop, and
the conventional PR inner voltage and current controllers (Gv
and Gi) generates a PWM signal to drive the IGBT inverter
gates. Inductive currents and capacitor voltages are transformed
to the stationary reference frame ( L
i αβ and c
v αβ ). Output
currents are transformed to the SRF ( odq
i ). The direct and
quadrature output currents are independently controlled by the
virtual impedance loop in dq axis. The inner voltage and current
loops are implemented in αβ reference frame since the PR
controller can deal with both positive and negative sequence
voltage when the negative sequence voltage and current appear.
Fig. 5 shows the simplified proposed control block diagram,
which includes the three-leg three-phase inverter, Lf-Cf filter,
line impedance, virtual impedance loop, the PLL and the inner
voltage and current control loops.
The closed loop transfer function Tplant (s) can be described as
follows:
( )
( )
( ) 1 ( ) ( )
1 ( ) ( ) ( ) ) )
(
( (
)
) (
o
ref
Lequ line
Lequ line vir Lequ
pla
o
nt
V s
V s
G s G s Z s
G s Z s G s G s s
T s
G s Z
⎡ ⎤
+
⎣ ⎦
=
+ + +
=
(10)
being
2
( ) ( )
( )
( ( ) )s 1 ( ) ( )
v i PWM
f f f i PWM f v i PWM
G s G s K
G s
L C s rC G s K C G s G s K
=
+ + + +
2
( )
( ( ) )s 1 ( ) ( )
f
o
f f f i PWM f v i PWM
sL r
Z s
L C s rC G s K C G s G s K
+
=
+ + + +
2 2
( ) iv
v pv
c
K s
G s K
s ω
= +
+
, ( )
i pi
G s K
= ,
1 1
( )
Lequ
Lequ Lequ
G s
R sL
= +
( )
line line line
Z s R sL
= + , ( ) virq
vird
vir
Lequ Lequ
R
R
G s
R sL
= +
where G(s) presents the tracking performance of the output
voltage following the voltage reference, ( )
o
Z s is the
equivalent output impedance of the inverter, ( )
line
Z s is the line
impedance, line
R is the line resistor, line
L is the line inductance,
( )
Lequ
G s is the equivalent load admittance, Lequ
R is the
equivalent resistor, Lequ
L is the equivalent inductance, o( )
V s is
the output voltage, ( )
ref
V s is the reference voltage, o ( )
i s is the
output current, ( )
v
G s is the PR voltage control loop, ( )
i
G s is
the proportional current control loop, PWM
K is the gain of three
phase inverter, f
L , f
C and r are the inductor, capacitor, and
inductor ESR of LC filter respectively, pv
K and iv
K are the
proportional and integral coefficients of voltage control loop,
c
ω is the resonant frequency of the PR voltage control loop,
pi
K is the proportional coefficients of current control loop,
vird
R and virq
R are the d-axis and q-axis virtual resistors.
The detailed derivative process is provided in the Appendix.
B. Control Principle
The proposed controller supplies a reference voltage to the
L
i αβ
( )
i
G s ( )
v
G s
f
L
PWM
dclink
n
dc
v f
C
÷
x
abc
αβ
abc
αβ
abc
dq
o
v αβ
c
i
L
i
ref
v
generator
abc
dq
ACbus
line
Z
oabc
i
Inner loop
INVERTER I
line
Z
.
.
.
s
s
INVERTER II
Droop CONTROL
odq
i
θ
αβ
dq
dq
αβ
/
P Q
odq
v
1
s
ω
vir
Z
Droop controller
ref
v
P
Q
Virtual impedance
m
n
*
ω*
V
o
i
load
Z
L
i αβ
( )
i
G s ( )
v
G s
f
L
PWM
dclink
n
dc
v f
C
÷
x
abc
αβ
abc
αβ
abc
αβ
o
v αβ
c
i
L
i
ref
v
generator
ref
v
αβ
dq
abc
αβ
ACbus
line
Z
SRF virtual impedance loop
oabc
i
od
i
oq
i
Inner loop
INVERTER I
line
Z
.
.
.
s
s
INVERTER II
PROPOSED CONTROL
virq
R
αβ
dq
vird
R
o
i αβ
vαβ
Δ
abc
dq
PI
PLL
1
s
base
ω
θ
θ
o
i
load
Z
(a) (b)
Fig. 4. Control structure comparison between (a) the conventional droop control and (b) the proposed control method.
7. TPEL-Reg-2015-03-0479 5
(s)
G
o
Z
vird
R
1
Lequ
R
1
Lequ
sL
virq
R
ref
V
sin
ref
V θ
ref
v '
ref
v
o
v
line
Z
bus
v
load
i
d
i
q
i
( )
plant
T s
Fig. 5. Simplified control block diagram.
0 50 100 150 200 250 300
-1
0
1
2
Frequench (Hz)
Phase
(deg)
0 50 100 150 200 250 300
-20
-10
0
10
20
Magnitude
(dB)
50 50.5 51 51.5 52
-0.5
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.2
50 50.5 51 51.5 52
-0.1
-0.05
0
0.05
0.1
Fig. 6. Bode diagram of the system transfer function.
inner loop. The voltage reference ref
V
→
is generated by
combining the amplitude reference (|Vref|) and the phase
generated (θ ) by the PLL.
Even though the PLL is trying to synchronize the inverter
with common AC bus, in case of supplying reactive loads, the
quadrature current flowing through the virtual resistance will
produce an unavoidable quadrature voltage drop, which will
cause an increase in PLL frequency. In other words, the PLL
will compel the inverter to be stabilized at a frequency point
with zero phase delay (ZPD) obtained from the system transfer
function. The frequency of ZPD is affected by the quadrature
current as shown in Fig. 6. Thus, the mechanism inherently
endows an droop characteristic in each inverter.
Similarly, in case of supplying active loads, the direct current
flowing through the virtual resistance will drop the direct
voltage, causing a decrease in the output voltage amplitude.
Hence, a droop characteristic is also imposed by the virtual
resistance adapting the amplitude of output voltage, which
endows to the system an Iod – V droop characteristic.
Moreover, the settling time can be considerably improved
because the proposed controller does not require any power
calculation. The bandwidth of the PLL can be designed through
the linearized model [45], [46] to be higher than the bandwidth
of the LPF that is used for PQ calculation purposes in the
Fig. 7 Bode diagram of the PLL (red line) and the LPF (blue line)
conventional droop controller [47]. The cutoff frequency of the
LPF in the power droop control loop is usually preassigned to
30 rad/s to obtain the average power while avoiding undesirable
interaction [45], [46]. The bandwidth of the PLL in the
proposed control is 1100 rad/s when kp_PLL and ki_PLL are equal
to 1.4 and 1000 respectively. The Bode diagram is shown in
Fig. 7. However, the fastest transient response of PLL should be
almost equal to the transient response speed of the inner voltage
control loop to ensure the system stability.
V.INHERENT DROOP CHARACTERISTIC AND COUPLING
ANALYSIS
Considering the inherent mechanism of with voltage
amplitude and with frequency, two virtual resistances Rvird
and Rvirq are employed to share the quadrature and direct load
currents among the inverters individually.
A. sharing
When the inverters and loads all connect to the common AC
bus, the proposed controller will make the system stable at a
frequency-stable operation point which may has a small
deviation from 50 Hz. The small deviation is determined by the
function of PLL, Rvirq and . The frequency-stable operation
should be the cross zero point of the phase-frequency
characteristics of the closed-loop transfer function of the
system, as depicted in the dashed part in Fig. 5.
Therefore, the parallel inverters will operate on the same
system frequency, but with different phase angles that depend
on the output quadrature current and q-axis virtual resistance
value.
Based on (10), as s jω
= , the relationship of vird
R , virq
R ,
od
I , oq
I and angular frequency ( ) can be calculated based
on
tan ( ) 0
plant
arc T jω
⎡ ⎤ =
⎣ ⎦ (11)
oq
I ω
−
-50
-40
-30
-20
-10
0
10
System: GPLL
Frequency (rad/s): 1.1e+03
Magnitude (dB): -3.01
System: GLPF
Frequency (rad/s): 30.2
Magnitude (dB): -3.04
Magnitude
(dB)
10
0
10
1
10
2
10
3
-135
-90
-45
0
Phase
(deg)
Bode Diagram
Frequency (rad/s)
od
I
oq
I
oq
I
oq
I
ω
8. TPEL-Reg-2015-03-0479 6
In order to analyze the relationship of , and ,
and are preset to a fixed value. The relationship of
, and with different line impedances is shown in
Fig. 8. Figs. 8 (a.1) and 8 (b.1) show the relationship with zero
line impedance. Figs. 8 (a.2) and 8 (b.2) describe the
relationship with resistive-inductive line impedance (Lline = 1.7
mH, Rline = 1 Ω). Figs. 8 (a.3) and 8 (b.3) present the
relationship with purely inductive line impedance (Lline = 1.8
mH). The inherent mechanism of the proposed oq
I ω
− droop
controller with different line impedances are depicted in Figs. 8
(b.1), 8 (b.2) and 8 (b.3). Fig. 8 indicates that the line
impedances in this range barely have effect on the relationship
of , and , as well as oq
I ω
− droop characteristics.
This is because the influence of the inductive line impedance in
this range has been compensated by the virtual resistors. As
observed in Figs. 8 (b.1), 8 (b.2) and 8 (b.3), the quadrature
current sharing among the parallel inverters can be adjusted by
regulating the q-axis virtual resistance ratio.
By contrast, the relationships of variables , and
with different line impedances are derived by assigning
and to certain values. The relationships of , and
with zero, resistive-inductive, and purely inductive line
impedance are shown in Figs. 9 (a.1) to 9 (a.3) respectively.
Additionally, Figs. 9 (b.1), 9 (b.2) and 9 (b.3) are obtained by
assuming to different values based on the relationships of
, and under different line impedance conditions.
As observed from Figs. 9 (b.1) to 9 (b.3), the influence of
direct output current on angular frequency changes by an
exponential dependence when it getting closer to the resonance
frequency of PR controller, which means that the impact of
and on can be neglected.
B. sharing
In order to share active loads, the parallel inverters will have
different output voltage amplitude deviations from the voltage
amplitude reference , which depend on the output direct
current and d-axis virtual resistance value of each inverter.
The voltage drop ( ) can be divided into two parts as
follows:
'
0
1 (j )
od vird ref plant
V I R V T ω
⎡ ⎤
Δ = + −
⎣ ⎦ (12)
where the '
0
ω is the angular frequency of frequency-stable
operation point.
The first part of (12) is the product of d-axis virtual
resistance and direct current output , which
dominantly affects the output voltage amplitude drop. The
second part of (12) is caused by the magnitude attenuation of
closed-loop transfer function which results from the small but
nonlinear frequency deviation due to the characteristic of PR
controller. However, as discussed above, the system frequency
will be stable and the deviations among the parallel inverters
will be equal to each other, that is, the voltage deviations
resulting from the second part of (12) are also the same among
inverters. Therefore, the influence on the deviations can be
neglected. Thus, the per-unit value of output voltage amplitude
can be derived from (10) as follows:
(13)
The parameters of and are fixed to analyze the
Zero line impedance Resistive-inductive line impedance Purely inductive line impedance
(a. 1) (a. 2) (a. 3)
(b. 1) (b. 2) (b. 3)
Fig. 8. The relationship of , and with different line impedances. (a) The relationship of , and with different line impedances, (b) The
relationship of and when Rvirq=1Ω/2Ω with different line impedances.
virq
R oq
I ω
vird
R od
I
virq
R oq
I ω
virq
R oq
I ω
vird
R od
I ω
virq
R
oq
I vird
R od
I
ω
vird
R
vird
R od
I ω
vird
R od
I ω
od
I
ref
V
V
Δ
vird
R od
I
(s) ( , , , , )
o
plant od oq vird virq
ref
V
T f I I R R
V
ω
= =
virq
R oq
I
I
oq
(A)
310 315 320
-4
-2
2
4
6
8
310 315 320
-4
-2
2
4
6
8
310 315 320
-4
-2
2
4
6
8
virq
R oq
I ω virq
R oq
I ω
oq
I ω
9. TPEL-Reg-2015-03-0479 7
Zero line impedance Resistive-inductive line impedance Inductive line impedance
(a. 1)
(a. 2)
(a. 3)
(b. 1) (b. 2) (b. 3)
Fig. 9. The relationship of Rvird, , and with different line impedances. (a) The relationship of Rvird, , and with different line impedances, (b) The
relationship of and when Rvird=1Ω/2Ω with different line impedances respectively.
relationship of , and . The relationship of ,
and with zero, resistive-inductive, and purely inductive
line impedances line impedance are shown in Fig. 10. As it can
be seen that the line impedances in the certain range barely have
effect on the relationship of , and . Figs. 10 (b.1) to
10 (b.3) shows the inherent droop mechanism of the
proposed controller under different line impedance conditions.
As observed, as the output direct current increases, the
voltage amplitude decreases with different ratio
corresponding to different values. Thus, the direct current
sharing among the parallel inverters can be adjusted by
regulating the d-axis virtual resistance ratio.
Similarly, , are fixed to analyze the effect of
frequency deviation on the voltage amplitude with different
line impedances. The relationships of , and with
zero, resistive-inductive, and purely inductive line impedance
are shown in Figs. 11 (a.1) to 11 (a.3) respectively. Figs. 11 (b.1)
to 11 (b.3) indicate that the relationship o
V ω
− almost immune
Zero line impedance Resistive-inductive line impedance Purely inductive line impedance
(a. 1) (a. 2)
V
o
(p.u.)
Iod (A)
Rvird (Ω)
(a. 3)
(b. 1) (b. 2) (b. 3)
Fig. 10. The relationship of , and with different line impedances. (a) The relationship of , and with different line impedances, (b) The
relationship of and when Rvird=1Ω/2Ω with different line impedances respectively.
ω (rad/s)
Rvird (Ω)
310 315 320
-20 000
-10 000
10 000
310 315 320
-500
500
310 315 320
-6000
-4000
-2000
2000
4000
6000
8000
od
I ω od
I ω
od
I ω
vird
R od
I o
V vird
R
od
I o
V
vird
R od
I o
V
od o
I V
−
od
I
o
V
vird
R
vird
R od
I
o
V
virq
R ω o
V
2 4 6 8 10
0.94
0.96
0.98
1.00
2 4 6 8 10
0.93
0.94
0.95
0.96
0.97
0.98
0.99
Rvird=1
Rvird=2
Iod (A)
2 4 6 8 10
0.94
0.96
0.98
1.00
vird
R od
I o
V vird
R od
I o
V
od
I o
V
10. TPEL-Reg-2015-03-0479 8
to both and different line impedances. The effects of
and on are nonlinear but quite small in
comparison with the voltage drop caused by adjusting
and . Considering that the voltage drop caused by , is
approximately the same in each inverter, it can be neglected.
Consequently, it can be observed a very well decoupling
between Iod and Ioq for a large set of X/R ratios (from purely X to
purely R).
C. Virtual impedance design
The virtual impedances in the proposed control loop are used
to generate the direct and quadrature voltage deviations by
multiplying the direct or quadrature currents separately. The
direct and quadrature voltage deviations are used to
automatically adjust the amplitude and phase angular of
inverter output voltage. Given that virtual impedances induce
output voltage and frequency deviation, they should be chosen
to ensure that the voltage and frequency deviations are in the
permissible range. For example, the maximum voltage
deviation (ΔVmax) is 10%, while the maximum frequency
deviation (Δfmax) is 0.5 Hz in a low voltage network.
The relationship between the maximum voltage magnitude
deviation ΔVdmax and Iod can be derived as follows:
max
d vird od
V R I
Δ = ⋅ (14)
In an extreme case, the inverter is assumed to supply only
active current. (1) can be presented as follows:
max _ max _max
vird od
V R I
Δ = ⋅ (15)
where, _ max
od
I is the maximum d-axis current of the inverter.
Thus, the upper limitation of the d-axis virtual resistor can be
described as follows:
max
_ max
_
vird
o rate
V
R
I
Δ
= (16)
Similarly, in an extreme case, the inverter is assumed to
supply only reactive current. The relationship between the
maximum angular frequency max
ω , quadrature output current
Ioq and Rvirq can be derived from (11), as expressed in (17):
_ max
virq
n
n
um
R
de
= (17)
being:
2
max max max
2
max
2 2 2
_ max max max
2 2
2
2 2 2
x
2
m
2
a
)
( [ (1
( )(
[ (
)
)]
)
( )]
2
ref o iv f f
f pv pi PWM o
oq pi PWM iv pv
pv o o
num V K C L
C K K K r
I K K K K
en
K
d
ω ω ω ω
ω ω
ω ω
ω ω ω
= − +
+ + −
+
+ −
=
,
where ref
V is the voltage reference magnitude, o
ω is the
fundamental frequency, PWM
K is the gain of three-phase
inverter, and _ max
od
I is the maximum d-axis current output of
the inverter.
This relationship is more complex than the relationship of
ΔVdmax, Iod_max and Rvird_max because the frequency of the
proposed system is affected not only by the virtual resistance
and quadrature current but also by the PR voltage control loop.
Based on (17), the maximum q-axis virtual resistance can be
calculated.
On the other hand, another functionality of the virtual
Zero line impedance Resistive-inductive line impedance Purely inductive line impedance
(a. 1) (a. 2) (a. 3)
(b. 1) (b. 2) (b. 3)
Fig. 11. The relationship of , and with different line impedances. (a) The relationship of , and with different line impedances, (b) The
relationship of and when Rvirq=1Ω/2Ω with different line impedances respectively.
virq
R
virq
R ω o
V
vird
R
od
I ω
Δ
ω (rad/s)
Rvird (Ω)
312 314 316 318 320 322
0.928
0.930
0.932
0.934
0.936
0.938
312 314 316 318 320 322
0.930
0.935
0.940
312 314 316 318 320 322
0.930
0.935
0.940
virq
R ω o
V virq
R ω o
V
ω o
V
11. TPEL-Reg-2015-03-0479 9
310 315 320
-4
-2
2
4
(a)
310 315 320
5
10
(b)
Fig. 12. The relationship of Ioq and ω when the line impedances are equal to
the maximum values. (a) Lline is equal to 6 mH, (b) Rline is equal to 15 Ω.
resistance is to compensate the effects of line inductance. Thus,
the virtual resistor should not too small to predominate over the
output impedance of the converter.
D. The limitations of the line impedance
The limitations of the line impedance depend on the control
loop parameters, the virtual impedance and electrical
parameters. In this case, if the Rvird and Rvirq are both equal to 2
Ω, the maximum inductive line impedance and the maximum
resistive line impedance that are able to maintain the steady
state operation of the proposed parallel-inverter based system
can be calculated by (11). The maximum inductive line
impedance and the maximum resistive line impedance are
approximately 6 mH and 15 Ω respectively. The proposed
and oq
I ω
− droop characteristics will present
non-linear when the line impedance over the limitations, as
illustrated in Fig. 12.
In general, the proposed control strategy can provide good
control performance over a wide range of line impedance which
is hard to achieve by previously developed control strategies.
VI. EXPERIMENTAL RESULTS
An islanded experimental MG setup, which consists of three
Danfoss 2.2 kW inverters, a real-time dSPACE1006 platform,
LC filters, line impedance, resistive load and resistance
-inductance load has been built according to Fig.1, as shown in
Fig. 13. The switching frequency is set to 10 kHz. The electrical
setup and control system parameters are listed in Table I.
Different scenarios have been considered to test the
performances of the proposed controller. In addition, a two
parallel-inverters system has been used to compare and
evaluate the performance of the proposed control approach
Resistive load 1
Inductive load
Line
impedance
Resistive load 2
Line
impedance
Danfoss Inverters
dSPACE 1006
Fig. 13. Experimental setup.
TABLE I
POWER STAGE AND CONTROL SYSTEM PARAMETERS
Parameters
Value
Description
DG Inverter
and output
filter
Vdc DC voltage 650 V
VMG MG voltage 311 V
f MG frequency 50 Hz
fs Switching frequency 10 kHz
Lf Filter inductance 1.8 mH
Cf Filter capacitance 25 µF
Lline_1 Resistive – inductive line 1 Ω + 1.7 mH
Lline_2 Inductive line 1.8 mH
Loads (Figs.
16 and 17)
Zload1 Local load 1 57+j2.83 Ω
Zload2 Local load 2 57 Ω
Inner Loop
kpi Current proportional term 0.07
Kii Current integral term 0
Kpv Voltage proportional term 0.04
Kiv Voltage integral term 94
Droop
Control
kpP
Active power droop
proportional coefficient
5e-7
kiP
Active power droop
integral coefficient
6e-6
kpQ
Reactive power droop
proportional coefficient
1e-5
kiQ
Reactive power droop
integral coefficient
0
Rv Virtual resistance 2 Ω
Lv Virtual inductance 8 mH
Proposed
Control
Kp_PLL PLL proportional term 1.4
Ki_PLL PLL integral coefficient 1000
Rvird1
d-axis virtual resistance
(inverter 1)
2 Ω
Rvirq1
q-axis virtual resistance
(inverter 1)
2 Ω
Rvird2
d-axis virtual resistance
(inverter 2)
2 Ω
Rvirq2
q-axis virtual resistance
(inverter 2)
2 Ω
Loads (Figs.
14 and 15)
Zload Local load 1
230+
j2.83 Ω
Ztest Step up load 460 Ω
with the conventional droop control. In this comparison, the
parameters of electrical and inner voltage and current loops are
all the same for both control methods.
od o
I V
−
12. TPEL-Reg-2015-03-0479 10
A. Comparison experiment with inductive line impedance
Fig. 14 shows the experimental results to compare the
control performance of the conventional droop control and the
proposed control with purely inductive line impedance which is
equal to 1.8 mH in three different scenarios. Figs. 14 (a.1) to 14
(a.6) shows the transient response when VCI #2 is connected to
VCI #1 with the conventional droop controller and the
proposed controller separately. As seen in Figs. 14 (a.1) to 14
(a.4), VCI #1 is connected to a resistive-inductive load feeding
around (1.16+j 0.4) A, while VCI #2 is disconnected. At 2.3 s,
VCI #2 is connected to VCI #1, operating in parallel supplying
a common load. The direct and quadrature currents output of
VCI #2 are increased by 0.58 A and 0.2 A respectively, whereas
the output direct and quadrature currents of the VCI #1 are
decreased also by 0.58 A and 0.2 A respectively. The settling
time is approximately 5.2 s with the conventional droop control,
whereas the settling time is approximately 1s with the proposed
control strategy. Notice that a small overshoot occurs due to
small voltage error between inverters at the moment of
connection, as shown in Fig. 14 (a.3). An offset approximately
0.03 A of reactive current when using the droop control can be
found in Fig. 14 (a.3) due to the unbalance between line
impedances, which is well suppressed when using the proposed
controller as shown in Fig. 14 (a.4). Fig. 14 (a.5) shows that
after 1.2 s the system frequency at 49.992 Hz was restored
closely to 49.996 Hz because of the decrease of the output
currents with conventional droop control. As can be observed
in Fig. 14 (a.6), the system frequency at 50.035 Hz was restored
to50.018 Hz. All these deviations in both cases are maintained
within the acceptable range, e.g., ±0.5 Hz.
Fig. 14 (b.1) to 14 (b.6) shows the transient response during
load step changes in the AC common bus. At the beginning, the
parallel VCIs operate with same power rates. At 1.3 s, an extra
460 Ω resistive load is connected to the common bus. The
direct currents output of VCI #1 and VCI #2 both increase by
0.31 A immediately to supply the needed current with
conventional droop control and the proposed controller as
shown in Figs. 14 (b.1) and 14 (b.2). The quadrature currents
output of VCI #1 and VCI #2 with the conventional droop
control deviate by approximately 0.03 A because of the
coupling between direct and quadrature currents as shown in
Figs. 14 (b.3). However, by using the proposed method the
quadrature currents output of VCI #1 and VCI #2 can maintain
their original values, being barely affected by the direct output
current disturbances as shown in Figs. 14 (b.4). The frequency
response to load disturbances for both VCI units is depicted in
Figs. 14 (b.5) and 14 (b.6).
The transient response for sudden direct currents sharing
ratio changes between the parallel VCIs is illustrated in Figs. 14
(c.1) to 14 (c.6). At the beginning, the VCI units parallel
operate with a common RL load. Both the VCI #1 and VCI #2
feeds are approximately 0.58 A of direct current and 0.2 A of
quadrature current. At 2.3 s, the direct current sharing ratio
between the parallel VCIs with the conventional droop control
has been suddenly changed from 1:1 to 1:2 and then changed
back to 1:1 at 10.6 s. As it can be seen in Fig. 14 (c.1), after
about maximum 6 s, the output currents of the parallel VCIs are
changed according to the new sharing ratio. Meanwhile, the
quadrature current sharing has been affected by the changes on
direct current sharing ratio as shown in Fig. 14 (c.3). By
contrast, the direct current sharing ratio between the parallel
VCIs with the proposed control approach has also been
suddenly changed from 1:1 to 1:2 at 1.6 s and then changed
back to 1:1 at 3.5 s. Fig. 14 (c.2) shows that the direct current
outputs of VCIs increase immediately according to the sharing
ratio changes and the transient response only lasts 0.2 s.
Meanwhile, the quadrature current sharing ratio is kept constant
via the decoupling control of the proposed controller.
B. Comparison experiment with resistive-inductive line
impedance
Fig. 15 shows the experimental results in order to compare
the conventional droop control and the proposed control, with
resistive-inductive line impedance which is equal to 1 Ω plus
1.7 mH in three different scenarios. Similarly Figs. 15 (a.1) to
15 (a.6) show the transient response of direct currents,
quadrature currents and frequency when the VCI #2 is
connected to VCI #1 with the conventional droop controller and
the proposed controller separately. Figs. 15 (b.1) to 15 (b.6)
illustrate the transient response for load step-up changes on AC
common bus. Figs. 15 (c.1) to 15 (c.6) present the transient
response during sudden direct currents sharing ratio changes
between the parallel VCIs. Both the conventional droop control
and the proposed controller can achieve stable operation. By
contrast, the proposed approach can endow the system with
faster response speed, smaller overshoot and decoupling
control. Oscillation appears in the output current and system
frequency with the conventional droop control due to the
resistive-inductive line impedance and the coupling between Iod
and Ioq.
When having almost zero line impedance, or highly resistive,
the parallel VCIs cannot operate by using the conventional
droop control. In contrast, excellent performance can be
obtained by using the proposed control as shown below.
For the rest of the tests, three parallel inverters have been
considered to test the performances of the proposed controller
with zero line impedance in the following scenarios.
C. Hot-swap operation (zero line impedance)
A three-parallel VCIs system sharing a linear load
(Rload1=57+j2.83 Ω) tests have been done to test individually the
effects of DG units connecting and disconnecting. The transient
response of the instantaneous currents, direct and quadrature
output currents and frequency with the proposed control are
illustrated in Fig. 16 (a), (b) and (c), respectively. As it can be
observed, at the beginning, the three VCI units are on parallel
operation with same power rates. At t2 and t3, VCI #2 and VCI
#3 are disconnected from VCI #1 separately, whereas VCI #1 is
responsible for supplying the total current. Fig. 16 indicates that
the output currents of VCI #2 and VCI #3 decrease to zero,
meanwhile, the output currents of VCI #1 is increased to 7.5 A
immediately. After the synchronization process, VCI #2 and
VCI #3 are re-connected to VCI #1 at t4 and t5 respectively. The
transient performance is smooth and fast that the slowest
settling time is about 0.8s. Furthermore, the current oscillations
are well damped.
13. TPEL-Reg-2015-03-0479 11
Inverter connection Load step changes Ratio changes
(a. 1) (b. 1) (c. 1)
(a. 2) (b. 2) (c. 2)
(a. 3) (b. 3) (c. 3)
(a. 4) (b. 4) (c. 4)
(a. 5) (b. 5) (c. 5)
(a. 6) (b. 6) (c. 6)
Fig. 14. Comparison experimental results with purely inductive line impedance in different scenarios.
0 1 2 3 4 5 6 7 8 9 10
-1.5
-1
-0.5
0
0.5
Time (s)
1
od
i
2
od
i
Droop control
0 1 2 3 4 5
-1
-0.8
-0.6
-0.4
-0.2
Time (s)
Droop control
1
od
i
2
od
i
0 2 4 6 8 10 12 14 16 18 20
-1
-0.8
-0.6
-0.4
Time (s)
Droop control
1
od
i
2
od
i
0 1 2 3 4 5 6 7 8 9 10
-1.5
-1
-0.5
0
0.5
Time (s)
1
od
i
2
od
i
0 1 2 3 4 5
-1
-0.8
-0.6
-0.4
Time (s)
1
od
i
2
od
i
0 1 2 3 4 5
-1
-0.8
-0.6
-0.4
Time (s)
1
od
i
2
od
i
0 1 2 3 4 5 6 7 8 9 10
-0.6
-0.4
-0.2
0
0.2
Time (s)
Droop control
2
oq
i
1
oq
i
0 1 2 3 4 5
-0.4
-0.3
-0.2
-0.1
0
Time (s)
Droop control
2
oq
i
1
oq
i
0 2 4 6 8 10 12 14 16 18 20
-0.25
-0.2
-0.15
Time (s)
Droop control
2
oq
i
1
oq
i
0 1 2 3 4 5 6 7 8 9 10
-0.6
-0.4
-0.2
0
0.2
Time (s)
2
oq
i
1
oq
i
0 1 2 3 4 5
-0.4
-0.3
-0.2
-0.1
0
Time (s)
2
oq
i
1
oq
i
0 1 2 3 4 5
0.25
-0.2
0.15
Time (s)
2
oq
i
1
oq
i
0 1 2 3 4 5 6 7 8 9 10
49.98
49.99
50
50.01
50.02
Time (s)
Droop control
2
f
1
f
0 1 2 3 4 5
49.95
50
50.05
50.1
Time (s)
Droop control
2
f
1
f
0 2 4 6 8 10 12 14 16 18 20
49.95
50
50.05
50.1
Time (s)
Droop control
1
f
2
f
0 1 2 3 4 5 6 7 8 9 10
50
50.02
50.04
50.06
50.08
Time (s)
2
f
1
f
0 1 2 3 4 5
50
50.01
50.02
50.03
50.04
Time (s)
1
f
2
f
0 1 2 3 4 5
49.95
50
50.05
50.1
Time (s)
1
f
2
f
14. TPEL-Reg-2015-03-0479 12
Inverter connection Load step changes Ratio changes
0 1 2 3 4 5 6 7 8 9 10
-1.5
-1
-0.5
0
0.5
Time (s)
1
od
i
2
od
i
(a. 1)
0 1 2 3 4 5
-1
-0.8
-0.6
-0.4
Time (s)
1
od
i
2
od
i
(b. 1)
0 2 4 6 8 10 12 14 16 18 20
-1
-0.8
-0.6
-0.4
Time (s)
1
od
i
2
od
i
(c. 1)
0 1 2 3 4 5 6 7 8 9 10
-1.5
-1
-0.5
0
0.5
Time (s)
1
od
i
2
od
i
(a. 2)
0 1 2 3 4 5
-1
-0.8
-0.6
-0.4
-0.2
Time (s)
1
od
i
2
od
i
(b. 2)
0 1 2 3 4 5
-1
-0.8
-0.6
-0.4
Time (s)
1
od
i
2
od
i
(c. 2)
0 1 2 3 4 5 6 7 8 9 10
-0.6
-0.4
-0.2
0
0.2
Time (s)
2
oq
i
1
oq
i
(a. 3)
0 1 2 3 4 5
-0.25
-0.2
-0.15
-0.1
-0.05
Time (s)
2
oq
i
1
oq
i
(b. 3)
0 2 4 6 8 10 12 14 16 18 20
-0.25
-0.2
-0.15
Time (s)
2
oq
i
1
oq
i
(c. 3)
0 1 2 3 4 5 6 7 8 9 10
-0.6
-0.4
-0.2
0
0.2
Time (s)
2
oq
i
1
oq
i
(a. 4)
0 1 2 3 4 5
-0.25
-0.2
-0.15
-0.1
Time (s)
2
oq
i
1
oq
i
(b. 4)
0 1 2 3 4 5
-0.25
-0.2
-0.15
-0.1
-0.05
Time (s)
2
oq
i
1
oq
i
(c. 4)
0 1 2 3 4 5 6 7 8 9 10
49.9
49.95
50
50.05
50.1
Time (s)
1
f 2
f
(a. 5)
0 1 2 3 4 5
49.9
49.95
50
50.05
50.1
Time (s)
2
f
1
f
(b. 5)
0 2 4 6 8 10 12 14 16 18 20
49.95
50
50.05
50.1
Time (s)
1
f
2
f
(c. 5)
0 1 2 3 4 5 6 7 8 9 10
49.9
49.95
50
50.05
50.1
Time (s)
1
f
2
f
(a. 6)
0 1 2 3 4 5
49.9
49.95
50
50.05
50.1
Time (s)
1
f 2
f
(b. 6)
0 1 2 3 4 5
49.95
50
50.05
50.1
Time (s)
1
f
2
f
(c. 6)
Fig. 15. Comparison experimental results with resistive-inductive line impedance in different scenarios.
16. TPEL-Reg-2015-03-0479 14
D. Direct and quadrature currents decoupling sharing with
different sharing ratio (zero line impedance)
In some cases, the parallel connected VCIs need to supply
active and reactive currents with different rates based on
different power rates, requirements from EMS or other superior
control loops. A three- parallel VCIs setup sharing a common
distributed linear load (Rload1=57+j2.83 Ω) has been built to test
the decoupling sharing performance of direct and quadrature
currents with different sharing ratios. As shown in Fig. 17, the
experiment can be divided nine stages. The different stages (S1
to S9) are described as follows:
S1 (t1-t2): The three VCIs are on parallel operation to share
the common load equally due to the same virtual resistances
S2 (t2-t3): The d-axis virtual resistance (Rvird) ratio of these
three paralleled VCIs is suddenly changed from 1:1:1 to
1.25:1:1 at t2. Thus, the direct current output of VCI #1 is
decreased immediately, whereas the direct currents output of
VCI #2 and VCI #3 are all increased by the same value within
0.1s. The change on active current does not influence on the
quadrature currents of these three VCIs as the theoretical
analysis.
S3 (t3-t4): The Rvird ratio is suddenly changed from 1.25:1:1
to 1.25:1.5:1 at t3. As observed, the output direct current of VCI
#2 is decreased to the desired value.
S4 (t4-t5): At t4, the paralleled system is subjected to a 50%
step up in the q-axis virtual resistance (Rvirq) of VCI #2. Thus,
the Rvirq ratio of these three VCIs is suddenly changed from
1:1:1 to 1:1.5:1. As observed, the output quadrature current
ratio becomes 1.5:1:1.5 which is the inverse proportion of the
virtual resistance ratio as the theoretical analysis. In addition,
the change on reactive current also does not affect the direct
currents.
S5 (t5-t6): The Rvirq ratio suddenly changes from 1:1.5:1 to
1:1.5:1.75 at t5.
S6 (t6-t7): At t6, the Rvird of VCI #1 reduces back to 2 Ω. Thus
the output direct current sharing ratio becomes 1.5:1:1.5.
S7 (t7-t8): At t7, the Rvirq of VCI #2 reduces back to 2 Ω.
Hence the direct current sharing ratio becomes 1.75: 1.75:1.
S8 (t8-t9): The Rvird ratio changes from 1:1.5:1 to 1:1:1 at t8.
S9 (t9-t10): The Rvirq ratio changes from 1:1:1.75 to 1:1:1 at t9.
Therefore, the output direct and quadrature currents of three
VCIs are equal again.
The proposed controller successfully regulates the output
currents of paralleled VCIs to the desired value. As can be
observed, even with different power rates, the VCI units with
the proposed control strategy will still maintain stable operation
and achieve the online sharing ratio change. The proposed
controller presents large stability margin to the control
variables Rvird and Rvirq.
In summary, the experimental results reveal that the
proposed control strategy does apply to low-voltage
parallel-VCI-based system where the line impedance usually
presents high ratio of R/X and short length because of its faster
response speed, online sharing ratio change function, larger
stability margin, smaller overshoot, plug‘n’play operation and
decoupling control. In addition, the proposed control strategy
also works well with inductive-resistive line impedance and
small purely inductive line impedance by means of virtual
72.1 72.15 72.2 72.25 72.3
-5
-2.5
0
2.5
5
62.1 62.15 62.2 62.25 62.3
-5
-2.5
0
2.5
5
72.1 72.15 72.2 72.25 72.3
-5
-2.5
0
2.5
5
62.1 62.15 62.2 62.25 62.3
-5
-2.5
0
2.5
5
72.1 72.15 72.2 72.25 72.3
-5
-2.5
0
2.5
5
62.1 62.15 62.2 62.25 62.3
-5
-2.5
0
2.5
5
20 20.1 20.2 20.3
-5
-2.5
0
2.5
5
2.5 2.55 2.6 2.65
-5
-2.5
0
2.5
5
20 20.1 20.2 20.3
-4
-2
0
2
4
2.5 2.55 2.6 2.65
-5
-2.5
0
2.5
5
20 20.1 20.2 20.3
-5
-2.5
0
2.5
5
2.5 2.55 2.6 2.65
-4
-2
0
2
4
(a)
17. TPEL-Reg-2015-03-0479 15
2.5 2.55 2.6 2.65
-4
-3.5
-3
-2.5
20 20.1 20.2 20.3
-5
-4
-3
-2
62.1 62.15 62.2 62.25 62.3
-4
-3.5
-3
-2.5
72.1 72.15 72.2 72.25 72.3
-4
-3.75
-3.5
-3.25
-3
2.5 2.55 2.6 2.65
-0.13
-0.12
-0.11
-0.1
-0.09
-0.08
20 20.1 20.2 20.3
-0.15
-0.125
-0.1
-0.075
-0.05
62.1 62.15 62.2 62.25 62.3
-0.15
-0.125
-0.1
-0.075
-0.05
72.1 72.15 72.2 72.25 72.3
-0.15
-0.125
-0.1
-0.075
-0.05
(b)
2.5 2.55 2.6 2.65
49.95
49.975
50
50.025
50.05
20 20.1 20.2 20.3
49.95
49.975
50
50.025
50.05
62.1 62.15 62.2 62.25 62.3
49.95
49.975
50
50.025
50.05
72.1 72.15 72.2 72.25 72.3
49.95
49.975
50
50.025
50.05
(c)
Fig. 17. Transient responses of DG1, DG2, and DG3 with different sharing ratio. (a) Instantaneous output currents of DG1-3, (b) Direct and quadrature output
currents of DG1-3, (c) Frequency of DG1-3
.
resistor. The proposed and oq
I ω
− droop
characteristics will present non-linear when the line impedance
over the limitations. Thus, the droop control strategy should be
applied to the high inductive system. In other cases, the
proposed control strategy can provide superior performances.
The prominent features of the proposed strategy compared with
the conventional droop control are summarized in Table II.
VII. CONCLUSION AND FUTURE WORK
A simpler and faster controller that comprises a PLL, a
virtual resistance loop and a PR controller in inner voltage loop
for controlling direct and quadrature load currents separately
among parallel three-phase inverters is developed. Based on the
steady state characteristic analysis, by adjusting the d-axis
virtual resistance ratio between the parallel inverters, the direct
load current sharing can be achieved. Whereas by modifying
the q-axis virtual resistance ratio between parallel inverters, the
quadrature load current provided will be changed
proportionally. The proposed control strategy does apply to
low-voltage microgrids and islanded minigrids. In addition, it
can also works well with inductive-resistive line impedance
and even small purely inductive or resistive line impedance
thanks to the use of virtual resistance. Compared with
conventional droop control, the described method does not
need to calculate active and reactive powers. Thus, the method
exhibits faster transient response and better precision.
Experimental results are included to show the excellent
behaviour of the proposed controller. The small signal model
and stability analysis will be presented in Part II of this paper.
APPENDIX
The detailed derivative process of (10) in Section IV is
shown as follows.
As indicated in Fig. 5, the closed loop includes three-leg
three-phase inverter, Lf-Cf filter, line impedance, inner voltage
and current control, and virtual resistance loop.
The block diagram of the inner current and voltage loops as
well as the LC filter is shown in Fig. A.1.
Based on the diagram, the closed-loop transfer function can
be written as follows:
'
o o o
( ) ( ) ( ) ( ) ( )
ref
v s G s v s Z s i s
= − (A.1)
being
2
( ) ( )
( )
( ( ) )s 1 ( ) ( )
v i PWM
f f f i PWM f v i PWM
G s G s K
G s
L C s rC G s K C G s G s K
=
+ + + +
(A.2)
od o
I V
−
18. TPEL-Reg-2015-03-0479 16
TABLE II
PERFORMANCE COMPARISON
Purely inductive line impedance
Resistive-inductive line
impedance
Zero or resistive line impedance
P-V/Q-f
droop
Proposed control
P-V/Q-f
droop
Proposed
control
P-V/Q-f droop
Proposed
control
Control
capability
Yes
Yes, but cannot work with large
inductive line impedance
Yes Yes
No, need change to
P-f/Q-V droop
Yes
Transient
response
Slow fast Slow fast Slow fast
Control
performance
Good
Good, but cannot work with large
inductive line impedance
Oscillations Good
Good (if with P-f/Q-V
droop)
Very well
Robustness Poor Good Poor Good Poor Good
Control
parameters
m, n, Zvir Rvird, Rvirq m, n, Zvir Rvird, Rvirq m, n, Zvir Rvird, Rvirq
( )
v
G s ( )
I
G s PWM
K
1
f
L s r
+
1
f
C s
o
i
'
ref
v o
v
L
i
Fig. A.1 Block diagram of the dual-loop control
2
( )
( ( ) )s 1 ( ) ( )
f
o
f f f i PWM f v i PWM
sL r
Z s
L C s rC G s K C G s G s K
+
=
+ + + +
(A.3)
2 2
( ) iv
v pv
c
K s
G s K
s ω
= +
+
(A.4)
( )
i pi
G s K
= (A.5)
where G(s) presents the tracking performance of the output
voltage following the voltage reference, ( )
o
Z s is the
equivalent output impedance of the inverter, o( )
v s is the output
voltage,
'
( )
ref
v s is the reference voltage of inner voltage loop,
o ( )
i s is the output current, ( )
v
G s is the PR voltage control
loop, ( )
i
G s is the proportional current control loop, PWM
K is
the gain of three phase inverter, f
L , f
C and r are the inductor,
capacitor, and inductor ESR of the LC filter respectively, pv
K
and iv
K are the proportional and integral coefficients of
voltage control loop, c
ω is the resonant frequency of the PR
regulator in voltage control loop, and pi
K is the proportional
coefficients of current control loop.
To obtain the direct and quadrature load currents, the
equivalent parallel connected resistive-inductive load can be
represented as follows:
1 1
( )
Lequ
Lequ Lequ
G s
R sL
= + (A.6)
where ( )
Lequ
G s is the equivalent load admittance, Lequ
R is the
equivalent resistor, and Lequ
L is the equivalent inductance.
The line impedance can be expressed as follows:
( )
line line line
Z s R sL
= + (A.7)
where ( )
line
Z s is the line impedance, line
R is the line resistor,
and line
L is the line inductance.
Hence, the closed loop transfer function Tplant(s) can be
derived based on Fig. 5.
( ) 1 ( ) ( )
( )
( ) 1 ( ) ( ) ( ) ( ) ( ) (
( )
)
Lequ line
o
ref Lequ line vir Lequ
plant
o
G s G s Z s
v s
v s G s Z s G s G s Z
s
G s s
T
⎡ ⎤
+
⎣ ⎦
=
+ + +
=
(A.8)
being ( ) virq
vird
vir
Lequ Lequ
R
R
G s
R sL
= +
REFERENCES
[1] Lasseter, R.H., "MicroGrids," Power Engineering Society Winter
Meeting, 2002. IEEE, vol.1, no., pp.305,-308, 2002
[2] Guerrero, J.M.; Chandorkar, M.; Lee, T.; Loh, P.C., "Advanced Control
Architectures for Intelligent Microgrids—Part I: Decentralized and
Hierarchical Control," Industrial Electronics, IEEE Transactions on,
vol.60, no.4, pp.1254,-1262, April 2013
[3] Piagi, P., Lasseter, R.H., "Autonomous control of microgrids," Power
Engineering Society General Meeting, 2006. IEEE, vol., no., pp., 2006
[4] Yunwei Li, Vilathgamuwa, D.M., Poh Chiang Loh, "Design, Analysis,
and Real-Time Testing of a Controller for Multibus Microgrid System,"
IEEE Transactions on Power Electronics, vol. 19, no. 5, pp.
1195–1204, Sept. 2004.
[5] Guerrero, J.M., Garcia De Vicuna, L., Matas, J., Castilla, M., Miret, J.,
"Output Impedance Design of Parallel-Connected UPS Inverters With
Wireless Load-Sharing Control," IEEE Transactions on Industrial
Electronics, vol. 52, no. 4, 1126-1135, Aug. 2005.
[6] Vasquez, J.C., Guerrero, J.M., Luna, A., Rodriguez, P., "Adaptive
Droop Control Applied to Voltage-Source Inverters Operating in
Grid-Connected and Islanded Modes," Industrial Electronics, IEEE
Transactions on, vol. 56, no. 10, 4088-4096, Oct. 2009.
[7] Jaehong Kim, Guerrero, J.M., Rodriguez, P., Teodorescu, R.,
Kwanghee Nam, "Mode Adaptive Droop Control With Virtual Output
19. TPEL-Reg-2015-03-0479 17
Impedances for an Inverter-Based Flexible AC Microgrid," Power
Electronics, IEEE Transactions on, vol. 26, no. 3, pp. 689-701, March.
2011.
[8] R. H. Lasseter and P. Paigi, “Microgrid: A conceptual solution,” in
Proc. IEEE PESC, Aachen, Germany, 2004, pp. 4285-4290.
[9] M. Marwali, J.-W. Jung, and A. Keyhani, “Control of distributed
generation systems—Part II: Load sharing control,” IEEE Trans.
Power Electron., vol. 19, no. 6, pp. 1551–1561, Nov. 2004.
[10] F. Katiraei and M. R. Iravani, “Power management strategies for a
microgrid with multiple distributed generation units,” IEEE Trans.
Power Syst., vol. 21, no. 4, pp. 1821–1831, Nov. 2006.
[11] Chandorkar, M.C., Divan, D.M., Adapa, R., "Control of parallel
connected inverters in standalone AC supply systems," Industry
Applications, IEEE Transactions on, vol.29, no.1, pp.136,-143, Jan/Feb
1993
[12] J. Guerrero, L. de Vicuna, J. Matas, M. Castilla, and J. Miret, “A
wireless controller to enhsance dynamic performance of parallel
inverters in distributed generation system,” IEEE Trans. Power
Electron., vol. 19, no. 5, pp. 1205–1213, Sep. 2004.
[13] Ashabani, S.M.; Mohamed, Y.A.-R.I. "New Family of Microgrid
Control and Management Strategies in Smart Distribution
Grids—Analysis, Comparison and Testing", Power Systems, IEEE
Transactions on, On page(s): 2257-2269 Volume: 29, Issue: 5, Sept.
2014
[14] C. Sao, P. Lehn, "Autonomous load sharing of voltage source
converters," IEEE Trans. Power Del., vol. 20, no. 2, pp. 1009–1016,
Apr. 2005.
[15] Yasser Abdel-Rady Ibrahim Mohamed, Ehab F. El-Saadany. "Adaptive
Decentralized Droop Controller to Preserve Power Sharing Stability of
Paralleled Inverters in Distributed Generation Microgrids," IEEE
Transactions on Power Electronics, vol. 23, no. 6, pp.2806-2816, Nov.
2008
[16] Yajuan Guan, Weiyang Wu, Xiaoqiang Guo, Herong Gu. "An
Improved Droop Controller for Grid-Connected Voltage Source
Inverter in Microgrid." 2nd International Symposium on Power
Electronics for Distributed Generation Systems, PEDG 2010, 2010:
823-828
[17] S. J. Chiang, C. Y. Yen, and K. T. Chang, “A multimodule parallelable
series-connected PWM voltage regulator,” IEEE Trans. Ind. Electron.,
vol. 48, no. 3, pp. 506–516, Jun. 2001.
[18] Y. W. Li, C. N. Kao, “An accurate power control strategy for
powerelectronics- interfaced distributed generation units operating in a
low voltagemultibus microgrid,” IEEE Trans. Power Electron, vol. 24,
no. 12, pp. 2977–2988, Dec. 2009.
[19] Engler, A., Soultanis, N., "Droop control in LV-grids," Future Power
Systems, 2005 International Conference on, vol., no., pp.6 pp.,6, 18-18
Nov. 2005
[20] Guerrero, J.M., Matas, J., Luis Garcia de Vicuna, Castilla, M., Miret, J.,
"Decentralized Control for Parallel Operation of Distributed
Generation Inverters Using Resistive Output Impedance," Industrial
Electronics, IEEE Transactions on, vol.54, no.2, pp.994,-1004, April
Apr. 2007
[21] H. Laaksonen, P. Saari, and R. Komulainen, “Voltage and frequency
control of inverter based weak LV network microgrid,” in Proc. 2005
Int. Conf. Future Power Systems, Amsterdam, The Netherlands, Nov.
18, 2005.
[22] Karel De Brabandere, Bruno Bolsens, Jeroen Van den Keybus, et al, “A
Voltage and Frequency Droop Control Method for Parallel Inverters,”
IEEE Trans. Power Electronics, vol. 22, no. 4, pp. 1107-1115, July.
2007
[23] Vandoorn, T.L.; Meersman, B.; De Kooning, J.D.M.; Vandevelde, L.
"Directly-Coupled Synchronous Generators With Converter Behavior
in Islanded Microgrids", Power Systems, IEEE Transactions on, On
page(s): 1395-1406 Volume: 27, Issue: 3, Aug. 2012
[24] W. Yao,M. Chen, J. M. Guerrero, and Z.-M. Qian, “Design and analysis
of the droop control method for parallel inverters considering the
impact of the complex impedance on the power sharing,” IEEE Trans.
Ind. Electron., vol. 58, no. 2, pp. 576–588, Feb. 2011.
[25] Vandoorn, T.L., De Kooning, J.D.M., Meersman, B., Guerrero, J.M.,
Vandevelde, L., "Voltage-Based Control of a Smart Transformer in a
Microgrid," Industrial Electronics, IEEE Transactions on, vol.60, no. 4,
pp. 1291-1305, Apr. 2013.
[26] E. Rokrok and M. E. H. Golshan, “Adaptive voltage droop method for
voltage source converters in an islanded multibus microgrid,” IET Gen.,
Trans., Dist., vol. 4, no. 5, pp. 562–578, 2010.
[27] G. Diaz, C. Gonzalez-Moran, J. Gomez-Aleixandre, and A. Diez,
“Scheduling of droop coefficients for frequency and voltage regulation
in isolated microgrids,” IEEE Trans. Power Syst., vol. 25, pp. 489–496,
Feb. 2010
[28] Majumder, R., Chaudhuri, B., Ghosh, A., Majumder, R., Ledwich, G.,
Zare, F., "Improvement of Stability and Load Sharing in an
Autonomous Microgrid Using Supplementary Droop Control Loop,"
Power Systems, IEEE Transactions on, vol. 25, no. 2, 796-808, May.
2010.
[29] Lee, C-.T., Chu, C-.C., Cheng, P-.T., "A New Droop Control Method
for the Autonomous Operation of Distributed Energy Resource
Interface Converters," Power Electronics, IEEE Transactions on, vol.
28, no. 4, 1980-1993, April. 2013.
[30] Vandoorn, T.L., Meersman, B.; Degroote, L., Renders, B., Vandevelde,
L., "A Control Strategy for Islanded Microgrids With DC-Link Voltage
Control," Power Delivery, IEEE Transactions on, vol.26, no.2,
pp.703,-713, April Apr. 2011.
[31] Coelho, E.A.A., Cortizo, P.C., Garcia, P.F.D., "Small-signal stability
for parallel-connected inverters in stand-alone AC supply systems,"
Industry Applications, IEEE Transactions on, vol.38, no.2, pp.533,-542,
Mar/Apr. 2002.
[32] Vasquez, J.C., Guerrero, J.M., Savaghebi, M., Eloy-Garcia, J.,
Teodorescu, R., "Modeling, Analysis, and Design of
Stationary-Reference-Frame Droop-Controlled Parallel Three-Phase
Voltage Source Inverters," Industrial Electronics, IEEE Transactions
on, vol.60, no.4, pp.1271,-1280, Apr. 2013
[33] C. Sao and P. Lehn, "Control and power management of converter fed
microgrids," IEEE Trans. Power Syst., vol. 23, no. 3, pp. 1088–1098,
Aug. 2008.
[34] Sao, C., Lehn, P.W., "Autonomous load sharing between converters
and generators in microgrids," Power and Energy Society General
Meeting, 2011 IEEE, San Diego, CA, pp, 1-8 , 24-29, July, 2011.
[35] Sato, E.K., Kawamura, A., Fujii, R., "Theoretical and experimental
verification of independent control for parallel-connected
multi-UPS's," Telecommunications Energy Conference, 2003.
INTELEC '03. The 25th International, Yokohama, Japan, pp, 485 – 492,
23-23, Oct. 2003.
[36] Sato, E.K., Kawamura, A., "Decentralized Control for Redundant
Parallelism of Uninterruptible Power Supplies with Different Ratings
Using Only Current Sensors," Power Electronics Specialists
Conference, 2005. PESC '05. IEEE 36th, Recife, pp, 2823 – 2829,
16-16, June, 2005.
[37] Mohammad S. Golsorkhi, Dylan D. C. Lu, "A Control Method for
Inverter-Based Islanded Microgrids Based on V-I Droop
Characteristics," Power Delivery IEEE Transactions on, vol.30, no.3,
pp.1196,-1204, June. 2015.
[38] Karel De Brabandere, Voltage and Frequency Droop Control in Low
Voltage Grids by Distributed Generators with Inverter Front-end.
Katholieke University Leuven, Leuven, Belgie, October 2006.
[39] Wu K D,Wu J C,Jou H L,"Simplified Control Method for
Parallel-Connected DC/AC Inverters," Electric Power Applications,
IEE Proceedings, pp, 787-792, 04, Dec. 2006.
[40] Batarseh, I.; Siri, K.; Lee, H., "Investigation of the output droop
characteristics of parallel-connnected DC-DC converters," Power
Electronics Specialists Conference, PESC '94 Record., 25th Annual
IEEE , vol.2, no., pp.1342-1351, Jun. 1994
[41] H. Kakigano, Y. Miura, T. Ise, and R. Uchida, "DC micro-grid for super
high quality distribution—System configuration and control of
distributed generations and energy storage devices, " in Proc. 37th
IEEE PESC, pp. 1-7, Jun. 2006.
[42] Xiaonan Lu, Guerrero, J.M., Kai Sun, Vasquez, J.C., "An Improved
Droop Control Method for DC Microgrids Based on Low Bandwidth
Communication with DC Bus Voltage Restoration and Enhanced
Current Sharing Accuracy," Power Electronics, IEEE Transactions on,
vol.29, no.4, pp. 1800-1812, April 2014
[43] Golestan, S.; Joorabian, M.; Rastegar, Hasan; Roshan, A.; Guerrero,
J.M., "Droop based control of parallel-connected single-phase inverters
in D-Q rotating frame," Industrial Technology, 2009. ICIT 2009. IEEE
International Conference on, vol., no., pp.1-6, 10-13 Feb. 2009
[44] Pedro Rodríguez, Alvaro Luna, Ignacio Candela, Ramon Mujal, Remus
Teodorescu, and Frede Blaabjerg, "Multiresonant Frequency-Locked
20. TPEL-Reg-2015-03-0479
Loop for Grid Synchronization of Power Conve
Grid Conditions," Industrial Electronics, IEE
vol.58, no.1, pp.127-138, Jan. 2011
[45] Se-Kyo Chung, "A Phase Tracking System for
Interface Inverters," Power Electronics, IEEE Tra
no.3, pp.431-438, May. 2000.
[46] Guo, X., Liu, W., Zhang, X., Sun, X., Lu, Z., Gue
Control Strategy for Grid-Connected Inverter Un
Faults Without PLL," Power Electronics, IEE
vol.30, no.4, pp. 1773-1778, April 2015
[47] Josep M. Guerrero, José Matas, Luis García de Vi
Jaume Miret, "Wireless-Control Strategy for P
Distributed-Generation Inverters," Industrial
Transactions on, vol.53, no.5, pp.1461-1470, Oct
Yajuan Guan (S’14) received
M.S. degree in Electrical En
Yanshan University, Qinhuang
2007 and 2010 respectively. Fr
was an Assistant Professor in
Engineering (IEE), Chinese A
(CAS). Since 2013, she has be
CAS. She is currently workin
degree at the Department of
Aalborg University, Denmark, a
Microgrids Research
(www.microgrids.et.aau.dk).
Her research interests include microgrids, distributed
power converter for renewable energy generation sy
services for microgrids.
Josep M. Guerrero (S’01-
received the B.S. degree in
engineering, the M.S. d
engineering, and the Ph.D
electronics from the Tec
Catalonia, Barcelona, in 1
respectively. Since 2011,
Professor with the Dep
Technology, Aalborg U
where he is responsible
Research Program. From
Professor at the Chinese Ac
the Nanjing University
Astronautics; from 2014 he is chair Professor in Shan
from 2015 he is a distinguished guest Professor in Hunan
His research interests is oriented to different microgr
power electronics, distributed energy-storage system
cooperative control, energy management systems, a
microgrids and islanded minigrids. Prof. Guerrero is an A
IEEE TRANSACTIONS ON POWER ELECTR
TRANSACTIONS ON INDUSTRIAL ELECTRONI
Industrial Electronics Magazine, and an Editor for the IEE
on SMART GRID and IEEE TRANSACTIONS on ENER
He has been Guest Editor of the IEEE TRANSACT
ELECTRONICS Special Issues: Power Electronics
Conversion and Power Electronics for Micr
TRANSACTIONS ON INDUSTRIAL ELECTRONIC
Uninterruptible Power Supplies systems, Renewabl
Distributed Generation and Microgrids, and Industri
Implementation Issues of the Kalman Filter; and the IEE
on SMART GRID Special Issue on Smart DC Distribution
chair of the Renewable Energy Systems Technical Co
Industrial Electronics Society. In 2014 he was awarded by
Highly Cited Researcher, and in 2015 he was elevated a
contributions on “distributed power systems and microgr
erters Under Distorted
EE Transactions on,
r Three Phase Utility
ansactions on, vol.15,
errero, J.M., "Flexible
nder Unbalanced Grid
EE Transactions on,
icuña, Miguel Castilla,
Parallel Operation of
Electronics, IEEE
t. 2006.
d the B.S. degree and
ngineering from the
gdao, Hebei, China, in
om 2010 to 2012, she
Institute of Electrical
Academy of Sciences
een a Lecturer in IEE;
ng toward her Ph.D.
Energy Technology,
as part of the Denmark
Programme
d generation systems,
ystems, and ancillary
M’04-SM’08-FM’15)
n telecommunications
degree in electronics
D. degree in power
hnical University of
997, 2000 and 2003,
he has been a Full
partment of Energy
University, Denmark,
e for the Microgrid
2012 he is a guest
cademy of Science and
of Aeronautics and
ndong University; and
n University.
rid aspects, including
ms, hierarchical and
and optimization of
Associate Editor for the
ONICS, the IEEE
ICS, and the IEEE
EE TRANSACTIONS
RGY CONVERSION.
TIONS ON POWER
s for Wind Energy
rogrids; the IEEE
CS Special Sections:
le Energy Systems,
ial Applications and
EE TRANSACTIONS
n Systems. He was the
ommittee of the IEEE
y Thomson Reuters as
s IEEE Fellow for his
rids.”
Xin Zhao receiv
Power Electroni
Northwestern Po
China, in 2010
currently workin
Department of
University, Denm
His research inte
converters, power
Juan C. Vasquez
degree in elect
Autonomous Univ
Colombia, and t
control, robotics,
Technical Univer
Spain, in 2004 and
the Autonomous U
taught courses on d
flexible manufactu
the Technical U
Post-Doctoral Ass
renewable energy systems. In 2011, he was
and currently he is working as an Associate
Energy Technology, Aalborg University,
co-responsible of the Research Program in
April. 2015 he was a Visiting Scholar at t
Systems (CPES) at Virginia Tech.
His current research interests include o
hierarchical control, optimization and powe
generation and ac/dc microgrids. Dr. Vasquez
System Evaluation Group SEG4 on LVDC D
Developed and Developing Economies and
Technical Committee TC-RES in IEEE Indus
Xiaoqiang Guo (M
Ph.D. degrees in ele
University, Qinhuan
respectively.
He has been a
Laboratory for Ele
Research (LEDAR)
ON, Canada. He is
with the Departm
Yanshan Unive
authored/coauthored
in addition to nine patents. His current resea
converters and ac drives, electric vehicle
energy power conversion systems.
Dr. Guo is a Senior Member of the IEEE Po
Industrial Electronics Society. He is an active
Sustainable Energy, IEEE Transactions on S
Industrial Electronics and IEEE Transactions
18
ved the B.S. and M.S. degree in
ics & Electrical Drives from
olytechnical University, Xi’an,
and 2013, respectively. He is
ng toward the Ph.D. degree at
Energy Technology, Aalborg
mark.
erests include control of power
r quality and microgrids.
(M’12-SM’14) received the B.S.
tronics engineering from the
versity of Manizales, Manizales,
the Ph.D. degree in automatic
and computer vision from the
rsity of Catalonia, Barcelona,
d 2009, respectively. He was with
University of Manizales, where he
digital circuits, servo systems, and
uring systems. He was also with
University of Catalonia, as a
sistant, teaching courses based on
Assistant Professor in microgrids
e Professor at the Department of
Denmark. Dr. Vasquez is the
Microgrids. From Feb. 2015 to
the Center of Power Electronics
operation, power management,
er quality applied to distributed
z is currently a member of the IEC
Distribution and Safety for use in
the Renewable Energy Systems
strial Electronics Society.
' 10-SM' 14) received the B.S. and
ectrical engineering from Yanshan
ngdao, China, in 2003 and 2009,
Postdoctoral Fellow with the
ectrical Drive Applications and
), Ryerson University, Toronto,
currently an associate professor
ment of Electrical Engineering,
ersity, China. He has
d more than fifty technical papers,
arch interests include high-power
charging station, and renewable
ower Electronics Society and IEEE
Referee for IEEE Transactions on
Smart Grid, IEEE Transactions on
s on Power Electronics.