Process improvement for General Counsel and Law FirmsGeorge Dunn
Â
Process improvement for General Counsel and Law Firms by George Dunn, President CRE8 Independent Consultants. A Follow Up To the 26th Annual General Counsel Conference. A white paper discussion of how law firms should approach process improvement using: Continuous process improvement; Business Process Management; Re-engineering; Lean and Six Sigma process improvement methods.
Asset finance system project initiation 101. âSelecting and implementing a new asset finance system? In the second of three articles, we go back to basics to take a look at what you need to consider at the start of your project to give yourself the best chance of success.â This has necessarily been a brief look at Project Initiation. We welcome comments and would be happy to help you get your project off to a good start.
PROCESS IMPOVEMENT PLAN Page | 1
PROCESS IMPOVEMENT PLAN
Submitted By:
Course number and name â
Submission Date: 3th June, 2021
TABLE OF CONTENTS
Introduction..............................................................................................................................3
Process Boundaries...................................................................................................................3
Process configuration................................................................................................................5
Process metrics..........................................................................................................................6
Targets for improved performance............................................................................................7
Introduction
The process improvement plan is the approach that seeks the side in which the ideas with weak processes in your established plan of business. It is the strategic based approach for improvement of business plan. There are different plan improvement methodologies that help to make better your plan and business idea. Process improvement involves the already present process in the business strategy which needs to be improved and enhanced it for better results. The steps include the identification of the process and its weak points, analyse the process and its effectiveness and coming up with strategic ideas to make it easier and convenient to implement. The improvement includes the better output and the satisfaction of the customer is their basic need. Setting new and advanced better practices can help out in improvement. Efficient strategy for identification, analysation and improvement are required. Finding weak links in the process chain and bottle necks which are the backbone of work and the next step is to identify the processes to nullify these from plans. These help to the better plan and make it to complete faster and easier without any hurdles. It helps to minimize the extra efforts that have been put up for the weak points that have been identified. It greases up the process and make it to regulate smoothly in the business run. Just identifying the problem and not doing a thing about it is not the solution of anything. It is just a counterproductive process. It is just like investing in the thing which you already knew that not giving you any profit. There is a flaw in anyoneâs work because human can do mistakes but accepting the mistake and doing efforts to eliminate is the process of plan improvement. There are various steps that have been involved in the improvement of plan such as mapping, analysing, redesigning of the plan, assigning the required solutions and then its implementation can help a lot in making the plan improved and good enough to put up.
Process Boundaries
It is the description of the basic purpose of the p ...
âSelecting and implementing a new asset finance system? In the second of three articles, we go back to basics to take a look at what you need to consider at the start of your project to give yourself the best chance of success.â
This has necessarily been a brief look at Project Initiation. We welcome comments and would be happy to help you get your project off to a good start.
Process improvement for General Counsel and Law FirmsGeorge Dunn
Â
Process improvement for General Counsel and Law Firms by George Dunn, President CRE8 Independent Consultants. A Follow Up To the 26th Annual General Counsel Conference. A white paper discussion of how law firms should approach process improvement using: Continuous process improvement; Business Process Management; Re-engineering; Lean and Six Sigma process improvement methods.
Asset finance system project initiation 101. âSelecting and implementing a new asset finance system? In the second of three articles, we go back to basics to take a look at what you need to consider at the start of your project to give yourself the best chance of success.â This has necessarily been a brief look at Project Initiation. We welcome comments and would be happy to help you get your project off to a good start.
PROCESS IMPOVEMENT PLAN Page | 1
PROCESS IMPOVEMENT PLAN
Submitted By:
Course number and name â
Submission Date: 3th June, 2021
TABLE OF CONTENTS
Introduction..............................................................................................................................3
Process Boundaries...................................................................................................................3
Process configuration................................................................................................................5
Process metrics..........................................................................................................................6
Targets for improved performance............................................................................................7
Introduction
The process improvement plan is the approach that seeks the side in which the ideas with weak processes in your established plan of business. It is the strategic based approach for improvement of business plan. There are different plan improvement methodologies that help to make better your plan and business idea. Process improvement involves the already present process in the business strategy which needs to be improved and enhanced it for better results. The steps include the identification of the process and its weak points, analyse the process and its effectiveness and coming up with strategic ideas to make it easier and convenient to implement. The improvement includes the better output and the satisfaction of the customer is their basic need. Setting new and advanced better practices can help out in improvement. Efficient strategy for identification, analysation and improvement are required. Finding weak links in the process chain and bottle necks which are the backbone of work and the next step is to identify the processes to nullify these from plans. These help to the better plan and make it to complete faster and easier without any hurdles. It helps to minimize the extra efforts that have been put up for the weak points that have been identified. It greases up the process and make it to regulate smoothly in the business run. Just identifying the problem and not doing a thing about it is not the solution of anything. It is just a counterproductive process. It is just like investing in the thing which you already knew that not giving you any profit. There is a flaw in anyoneâs work because human can do mistakes but accepting the mistake and doing efforts to eliminate is the process of plan improvement. There are various steps that have been involved in the improvement of plan such as mapping, analysing, redesigning of the plan, assigning the required solutions and then its implementation can help a lot in making the plan improved and good enough to put up.
Process Boundaries
It is the description of the basic purpose of the p ...
âSelecting and implementing a new asset finance system? In the second of three articles, we go back to basics to take a look at what you need to consider at the start of your project to give yourself the best chance of success.â
This has necessarily been a brief look at Project Initiation. We welcome comments and would be happy to help you get your project off to a good start.
Crafting a CMMI V2 Compliant Process for Governance Practice Area: An Experie...Dr. Mustafa DeÄerli
Â
DeÄerli, M. (2020). Crafting a CMMI V2 Compliant Process for Governance Practice Area: An Experiential Proposal. 14th Turkish National Software Engineering Symposium (UYMS 2020). 10.1109/UYMS50627.2020.9247068 â https://ieeexplore.ieee.org/xpl/conhome/9247008/proceeding
This is PMBOK Guide Planning Process Group Part three. It includes five Knowledge Area - Quality, Human Resource, Communications, Procurement and Stakeholder management - with five processes - Plan Quality Management, Plan Human Resource Management, Plan Communications Management, Plan Procurement Management, Plan Stakeholder Management - .
Foods Case Study
What to cover
Executive summary
Define Phase
Measure Phase
Analyze phase
Improve phase
Control Phase
Conclusion
1. Executive Summary
In December 2008, the company began to receive heavy surcharge from local authorities because of their poor water quality, mainly due to an excess of biological waste entering the sewer system.
Biological Oxygen Demand (BOD) The amount of oxygen needed by bacteria to decompose all the solid wastes in wastewater. Accounted for 74% of the resulting fees. The total bill for poor water quality reached $204,000 in 2009.
A six-sigma team was tasked to extremely reduce the BOD, after 6 months they reached 70% with a goal of 95%.
2. Define Phase
Project Charter
Project NameBOD Reduction at Kahiki FoodsCommencement DateSep, 2009Project SponsorKahiki FoodsCompletion DateDec, 2010Expected Hard Cost Reduction$195,000Expected % Reduction95%
Project Mission
The main objectives are:
Intense reduction in solid waste entering floor drains.
Increase output at different plant processes.
Green initiative for the organization.
$195,000 hard cost reduction.
Problem Statement
Per local authorities BOD levels shouldnât exceed 250mg/L
Kahiki had BOD waste levels of 3864mg/L, 1546% higher than upper spec limit
The source of the waste was obviously originating from inefficient floor drain management
6
Goal Statement
At least a 50% BOD reduction in 6 months and establishing a sustainable system able of reaching the goal of 95% reduction.
Process map
SIPOC map
8
3. Measure Phase
The waste removal system doesn't meet the spec.
Process Capability Charts
Measurement Plan
Demand Analysis
Metrics Used To Determine Water Quality
Biological Oxygen Demand (BOD)
Total Suspended Solids (TSS)
Total Kjeldahl Nitrogen (TKN)
BOD Process Capability Charts
TSS Process Capability Charts
Measurement Plan
N/B In any area of concern, should there be a negative response on any unit, the unit is rendered incomplete and therefore a defect.
13
Data Collection Challenges
System changed in 2007.
Standard sampling schedule 3 site visits/year moved to monthly.
Data collection visibility most critical points came from cleanup shift.
The above assessment was done by five individuals who were, one hired external expert, two quality assurance officers at the state government, while two are community professionals. MSA is an experimental process and require more views from different quotas of different levels of understanding to make independent judgments on quality (McCarty, 2005).
14
4. Analyze Phase
5 Why Analysis.
FMEA.
Gap analysis.
Fishbone diagram.
Hotspot heat map.
Regression Analysis.
Benchmarking.
5 Why Analysis
Plant Floor Drain Hotspot Heat Map
5. Improve phase
Improved Solid/Liquid Separation.
Reducing Waste Creation.
Employee Training.
Best Practice Identification.
WAP Committee: A "Waste Awareness Programâ.
Error Proofing: Adding visual S ...
Managing a three-dimensional (3D) printing facility was found to be more challenging than using the technology. Our research laboratory provides 3D printing services to students and faculty who need the technology to fulfill their education or research objectives. Students enrolled in Senior Design classes, in particular, rely on the availability of services to support their capstone projects. While demand increases, the laboratory becomes less efficient and sometimes chaotic. To improve the operations, Lean Six Sigma methods were applied to enhance effectiveness and efficiency. Through a DMAIC project, we enhanced the availability of resources for requestors and prevented delay or accumulation of work. The new operating procedures enabled the laboratory to provide quicker services with fewer mistakes. This case study demonstrates that Lean Six Sigma is not only useful in manufacturing but also in research and educational settings.
Crafting a CMMI V2 Compliant Process for Governance Practice Area: An Experie...Dr. Mustafa DeÄerli
Â
DeÄerli, M. (2020). Crafting a CMMI V2 Compliant Process for Governance Practice Area: An Experiential Proposal. 14th Turkish National Software Engineering Symposium (UYMS 2020). 10.1109/UYMS50627.2020.9247068 â https://ieeexplore.ieee.org/xpl/conhome/9247008/proceeding
This is PMBOK Guide Planning Process Group Part three. It includes five Knowledge Area - Quality, Human Resource, Communications, Procurement and Stakeholder management - with five processes - Plan Quality Management, Plan Human Resource Management, Plan Communications Management, Plan Procurement Management, Plan Stakeholder Management - .
Foods Case Study
What to cover
Executive summary
Define Phase
Measure Phase
Analyze phase
Improve phase
Control Phase
Conclusion
1. Executive Summary
In December 2008, the company began to receive heavy surcharge from local authorities because of their poor water quality, mainly due to an excess of biological waste entering the sewer system.
Biological Oxygen Demand (BOD) The amount of oxygen needed by bacteria to decompose all the solid wastes in wastewater. Accounted for 74% of the resulting fees. The total bill for poor water quality reached $204,000 in 2009.
A six-sigma team was tasked to extremely reduce the BOD, after 6 months they reached 70% with a goal of 95%.
2. Define Phase
Project Charter
Project NameBOD Reduction at Kahiki FoodsCommencement DateSep, 2009Project SponsorKahiki FoodsCompletion DateDec, 2010Expected Hard Cost Reduction$195,000Expected % Reduction95%
Project Mission
The main objectives are:
Intense reduction in solid waste entering floor drains.
Increase output at different plant processes.
Green initiative for the organization.
$195,000 hard cost reduction.
Problem Statement
Per local authorities BOD levels shouldnât exceed 250mg/L
Kahiki had BOD waste levels of 3864mg/L, 1546% higher than upper spec limit
The source of the waste was obviously originating from inefficient floor drain management
6
Goal Statement
At least a 50% BOD reduction in 6 months and establishing a sustainable system able of reaching the goal of 95% reduction.
Process map
SIPOC map
8
3. Measure Phase
The waste removal system doesn't meet the spec.
Process Capability Charts
Measurement Plan
Demand Analysis
Metrics Used To Determine Water Quality
Biological Oxygen Demand (BOD)
Total Suspended Solids (TSS)
Total Kjeldahl Nitrogen (TKN)
BOD Process Capability Charts
TSS Process Capability Charts
Measurement Plan
N/B In any area of concern, should there be a negative response on any unit, the unit is rendered incomplete and therefore a defect.
13
Data Collection Challenges
System changed in 2007.
Standard sampling schedule 3 site visits/year moved to monthly.
Data collection visibility most critical points came from cleanup shift.
The above assessment was done by five individuals who were, one hired external expert, two quality assurance officers at the state government, while two are community professionals. MSA is an experimental process and require more views from different quotas of different levels of understanding to make independent judgments on quality (McCarty, 2005).
14
4. Analyze Phase
5 Why Analysis.
FMEA.
Gap analysis.
Fishbone diagram.
Hotspot heat map.
Regression Analysis.
Benchmarking.
5 Why Analysis
Plant Floor Drain Hotspot Heat Map
5. Improve phase
Improved Solid/Liquid Separation.
Reducing Waste Creation.
Employee Training.
Best Practice Identification.
WAP Committee: A "Waste Awareness Programâ.
Error Proofing: Adding visual S ...
Managing a three-dimensional (3D) printing facility was found to be more challenging than using the technology. Our research laboratory provides 3D printing services to students and faculty who need the technology to fulfill their education or research objectives. Students enrolled in Senior Design classes, in particular, rely on the availability of services to support their capstone projects. While demand increases, the laboratory becomes less efficient and sometimes chaotic. To improve the operations, Lean Six Sigma methods were applied to enhance effectiveness and efficiency. Through a DMAIC project, we enhanced the availability of resources for requestors and prevented delay or accumulation of work. The new operating procedures enabled the laboratory to provide quicker services with fewer mistakes. This case study demonstrates that Lean Six Sigma is not only useful in manufacturing but also in research and educational settings.
Embracing GenAI - A Strategic ImperativePeter Windle
Â
Artificial Intelligence (AI) technologies such as Generative AI, Image Generators and Large Language Models have had a dramatic impact on teaching, learning and assessment over the past 18 months. The most immediate threat AI posed was to Academic Integrity with Higher Education Institutes (HEIs) focusing their efforts on combating the use of GenAI in assessment. Guidelines were developed for staff and students, policies put in place too. Innovative educators have forged paths in the use of Generative AI for teaching, learning and assessments leading to pockets of transformation springing up across HEIs, often with little or no top-down guidance, support or direction.
This Gasta posits a strategic approach to integrating AI into HEIs to prepare staff, students and the curriculum for an evolving world and workplace. We will highlight the advantages of working with these technologies beyond the realm of teaching, learning and assessment by considering prompt engineering skills, industry impact, curriculum changes, and the need for staff upskilling. In contrast, not engaging strategically with Generative AI poses risks, including falling behind peers, missed opportunities and failing to ensure our graduates remain employable. The rapid evolution of AI technologies necessitates a proactive and strategic approach if we are to remain relevant.
Instructions for Submissions thorugh G- Classroom.pptxJheel Barad
Â
This presentation provides a briefing on how to upload submissions and documents in Google Classroom. It was prepared as part of an orientation for new Sainik School in-service teacher trainees. As a training officer, my goal is to ensure that you are comfortable and proficient with this essential tool for managing assignments and fostering student engagement.
How to Make a Field invisible in Odoo 17Celine George
Â
It is possible to hide or invisible some fields in odoo. Commonly using âinvisibleâ attribute in the field definition to invisible the fields. This slide will show how to make a field invisible in odoo 17.
Model Attribute Check Company Auto PropertyCeline George
Â
In Odoo, the multi-company feature allows you to manage multiple companies within a single Odoo database instance. Each company can have its own configurations while still sharing common resources such as products, customers, and suppliers.
Acetabularia Information For Class 9 .docxvaibhavrinwa19
Â
Acetabularia acetabulum is a single-celled green alga that in its vegetative state is morphologically differentiated into a basal rhizoid and an axially elongated stalk, which bears whorls of branching hairs. The single diploid nucleus resides in the rhizoid.
Macroeconomics- Movie Location
This will be used as part of your Personal Professional Portfolio once graded.
Objective:
Prepare a presentation or a paper using research, basic comparative analysis, data organization and application of economic information. You will make an informed assessment of an economic climate outside of the United States to accomplish an entertainment industry objective.
Biological screening of herbal drugs: Introduction and Need for
Phyto-Pharmacological Screening, New Strategies for evaluating
Natural Products, In vitro evaluation techniques for Antioxidants, Antimicrobial and Anticancer drugs. In vivo evaluation techniques
for Anti-inflammatory, Antiulcer, Anticancer, Wound healing, Antidiabetic, Hepatoprotective, Cardio protective, Diuretics and
Antifertility, Toxicity studies as per OECD guidelines
Unit 8 - Information and Communication Technology (Paper I).pdfThiyagu K
Â
This slides describes the basic concepts of ICT, basics of Email, Emerging Technology and Digital Initiatives in Education. This presentations aligns with the UGC Paper I syllabus.
Read| The latest issue of The Challenger is here! We are thrilled to announce that our school paper has qualified for the NATIONAL SCHOOLS PRESS CONFERENCE (NSPC) 2024. Thank you for your unwavering support and trust. Dive into the stories that made us stand out!
Honest Reviews of Tim Han LMA Course Program.pptxtimhan337
Â
Personal development courses are widely available today, with each one promising life-changing outcomes. Tim Hanâs Life Mastery Achievers (LMA) Course has drawn a lot of interest. In addition to offering my frank assessment of Success Insiderâs LMA Course, this piece examines the courseâs effects via a variety of Tim Han LMA course reviews and Success Insider comments.
2. 116
Table 1
Key steps of DMAIC process (Kwak & Anbari, 2006)
steps Major activities
Define
Define the requirements and expectations of the customer, the project boundaries, the process by mapping the
business flow (such as SIPOC)
Measure
Measure the process to satisfy customerâs needs, develop a data collection plan and collect and compare data
to determine issues and shortfalls
Analyze
Analyze the causes of defects and sources of variation, determine the variations in the process and prioritize
opportunities for future improvement
Improve Improve the process to eliminate variations and develop creative alternatives and implement enhanced plan
Control
Control process variations to meet customer requirements, develop a strategy to monitor and control the
improved process and implement the improvements of systems and structures
The methodology is believed to be introduced in a US firm, where first, a team at Motorola developed
a process with four-phase âDefinitionââ ââAnalysisââ ââOptimizationââ and ââControlââ for improving
the products quality. Based on this four-phase process, two methodologies of Six Sigma were
developed: DMAIC (Define, Measure, Analysis, Improve, and Control) (Table 1), and DMADV
(Define, Measure, Analysis, Design, and Verify).
The DMAIC process was developed to eliminate defects in production or service processes (Ho et al.,
2008). The DMAIC cycle maintains many similarities with Demingâs cycle ââPlan-Do-Check-Actââ
(PDCA) and places more emphasis on integrating specific tools into each step of the method
(Schroeder et al., 2008; Kumar et al., 2008).
2. Problem statement
In any organization, outsourcing management has its own processes and activities and this process
may be varied in various organizations. Therefore, to improve outsourcing management process, the
characteristics of each organization should be considered. In this case study, outsourcing management
process was analyzed in a manufacturing company in the aerospace industry and several
improvement opportunities were identified in various areas such as âproduct qualityâ, âdelivery timeâ
and âproducts cost priceâ. According to the importance of customer satisfaction and due to the high
frequency of their complaints on delay time, reducing the delay of lead-time in the customer orders,
were considered. After this decision, the improvement project team was formed and managing
director of studied organization was chosen as the project administrator and the head of the project
team. After the team formation, the project charter was developed and as covenant (agreement)
between the project administrator and the project champion was signed.
This paper describes the methodology of the improvement project and its activities of definition and
implementation. In addition to improvement of the outsourcing management process, practice in team
working, enhancing creativity and the power of idea making and changing in managerial mental
paradigms are other outcomes of this project implementation.
3. Definition phase
In this phase, objective(s) and scope of the project are defined and information of process and
customer(s) are gathered. Activities of this phase are âtitling the projectâ, âproblem statementâ, and
âdrawing CTQ tree. Moreover, the names of the champion, team members, supervisors and
consultants, the project scope, the project objective, scheduling and Gantt chart, financial/non-
financial benefits and outcomes, required resources, SIPOC diagram, and VOC table are other items
of definition phase.
3. M. Cheshmberah and S. M. M. Nabavi / Uncertain Supply Chain Management 2 (2014) 117
3.1. Project Description
Considering that great deal of operations of the company are outsourced to outside suppliers, an
important source of delay is âlong timeâ of outsourcing process. In practice, it is possible to divide
the process into two sections, (1) the company and (2) the suppliers. Therefore, it is expected that
through some improvements, less delivery time is achievable.
3.2. Business case
The objective of this improvement project is to lessen the delivery delay and to increase the
customersâ satisfaction.
3.3. Project goal
The primary objective of the project is to address delivery delay expressed in three sub-objectives:
reducing the average time of contract negotiations up to 20%, reducing suppliersâ delay up to 15%
and lessening the average delivery time up to 20%.
3.4. Other expected results
Higher customersâ satisfaction, increased capacity, selecting proper suppliers, and providing
appropriate decision-making conditions are some of other expected results of the project.
3.5. Required financial resources
Based on the estimations, costs include training courses for suppliers, project team transportation for
information gathering, and implementing workshops.
3.6. Project schedule
It was estimated that the project takes 6 months, and schedule was codified based on the activities of
the 5 phases of DMAIC methodology through a Gantt chart.
3.7. Project structure
Due to the importance of senior manager's commitment, he undertook the role of âchampionâ. In
addition, to facilitate project implementation, the âproduction managerâ was chosen as the âproject
managerâ and was commissioned to choose the team members. After the formation of the project
team, âquality managerâ, âfinancial managerâ and a master black belt were chosen as âquality
supervisorâ, âfinancial supervisorâ and âthe project consultantâ. Fig. 1 illustrates the project structure.
Fig. 1. Project structure
Project champion
Project manager
Project team
Consultant (MBB)
Quality manager
Financial
manager
4. 118
3.8. SIPOC Diagram
SIPOC is a general diagram of process and provides a general view of suppliers, inputs, processes,
outputs and customers. This represents a flow diagram and is implemented to define and examine an
operation from the supplier to the customer (Basu & Wright, 2003). SIPOC ensures that all project
team members have a common perception of the process. Moreover, it helps the champion to see
which scope that is being worked on. In fact, SIPOC is a tool for determining project scope. Table 2
illustrates the SIPOC of the outsourcing process.
Table 2
SIPOC diagram of the process
Suppliers Inputs Process Outputs Customers
Customers Orders
Receiving customerâs
order
Final products Customers
Contracting with the
customer
Dividing the order
between the project
managers
Quality Dept. (QC
office)
Blank forms of quality
control
Identifying, Evaluating
and selecting the
supplier(s)
Supplierâs qualitative
performance records
Quality Dept. (quality
records office)
Suppliers
Filled forms of quality
control
Technical problems report Engineering Dept.
Quality Department
(monitoring office)
Engineering Dept.
Technical documents
(preliminary) Signing the purchase
contract
Project managers Suppliersâ information
Financial Dept. Financial resources (cash) Manufacturing technology
Project managers
Suppliers
Monitoring, tracking and
control of supplier(s)
Engineering Dept.
Suppliers Proposals
Delivering products to
companyâ warehouse by
the supplier(s) Quality control reports and
Alerts
Project managers
Commercial Dept.
Blank contract
The Rules and regulations Senior manager
Suppliers Products (not inspected)
Browsing commitments to
the customers
Suppliersâs financial
performance records
Senior manager
Receiving the products
from the supplier(s),
preparing & delivering to
the customer(s)
Financial Dept.
3.9. Voice of the Customer analysis
Customer requirements should drive management systems development (and improvement). The
purpose of specifications is to transmit the voice of the customers throughout the organization
(Pyzdek, 2003). It is applied to clarify the customerâs needs and understanding of the desired products
or services. Table 3 shows the results of voice of the customers regarding the outsourcing process.
3.10. Drawing Critical to Quality (CTQs) tree
In Six Sigma, the customer Critical to Quality Factors (CTQ) play the key role to agree and to define
critical quality factors as seen by customer. It is important that the customersâ requirements are
5. M. Cheshmberah and S. M. M. Nabavi / Uncertain Supply Chain Management 2 (2014) 119
understood when defining the CTQs (Basu & Wright, 2003). Figure 2 illustrates the CTQ tree of the
outsourcing process. Considering that the senior manager has chosen CTQ of âdelivery delayâ, it is
detailed in a separate tree (Fig. 3). In addition, Table 4 shows the CTQs definitions, which are
associated with defects definitions, and How to calculate the defect.
Table 3
The part of Voice of the Customer analysis
Why
How
Where
who
When
What
VOC
Customer
---
In comparison to similar
foreign prices and other
competitors
In all cases
---
always
Some of the
orders
High price
Customer 1 ---
Nonconformity with the
customer's requirements
and standards (Leading to
rework or scrap)
In all cases
---
sometimes
Some of the
orders
High number of
non-conforming
parts
---
delay in delivery after due
date
In all cases
---
always
Many of the
orders
Fulfilling the
commitments
with delay
They were
not well
justified or
do have
insufficient
importance
Often are incompletely
presented
In almost all
cases
Suppliers
and
observers
always
Control
guidelines
Generally blank
forms are not
filled out
completely
Quality Dept.
They were
not well
justified or
do have
insufficient
importance
Often are incompletely
presented or not presented
at all
In almost all
cases
suppliers
always
FPC and
other
process
diagrams
FPC and other
process diagrams
are partially
delivered or not
delivered at all
Project managers
Determining the base time
Reducing the delivery delay
Reducing the time of outsourcing
process
Reduction of non-conforming
parts
Improving the quality of the delivered
products
Improvement in outsourcing
process
Reduction of process costs
Reducing the price
VOC
+
Requirements of process
owner
Reduction of contract costs (with
the suppliers)
Determining the base price
Fig. 2. CTQ tree of the process
Contract with the customer
Internal process Contract with the supplier(s)
Reducing the time of
outsourcing process
Delivery to the customer
Producing and delivery to the company
Suppliers
Fig. 3. Detailed CTQ of reducing the time of outsourcing process
6. 120
Table 4
The CTQs definitions, related defects definitions, and How to calculate the defect
Process requirements (CTQ) definition of the defect How to calculate the defect
Reduction of the average time of
contracting
Up to 30 days 30 minus real time of contracting
Reduction of supplier delay
Difference between âin the contractâ and
âhappenedâ delivery time
âin the contractâ delivery time
minus âhappenedâ delivery time
Reduction of the average time of
delivery to the customer
Up to 30 days
30 minus real time of delivery to
the customer
4. Measure Phase
The primary objective of this phase is to specify the place and source of the problem by providing a
realistic understanding of the problem and the process. Such insight helps us to limit the range of
potential causes. The key elements of this phase include establishing a plan for data collection,
analyzing variations and determining the level of Sigma performance (Basu & Wright, 2003)
(Pyzdek, 2003). Different steps of measure phase are as follows:
Table 5
FMEA table for the process
requirements
of
the
process
Modes
of
potential
failure
Potential
impacts
of
failure
Strength
(S)
Causes
of
potential
failure
Occurrence
(O)
Current
controls
of
process
Diagnosis
(D)
RPN
On-time
delivery
Delay
in
delivery
time
Increased price
5
Weak assessment of staffsâ
capacity
10
Assignment sheets, project control
forms 6 420
Customer
dissatisfaction
7
Failing to assess suppliersâ capacity 10
Project managerâs point of view,
evaluating suppliers
6 420
Technical weakness of the
suppliers
10
Project managerâs point of view,
evaluating suppliers
6 420
Reduction of
capacity
6 Insufficient identified suppliers
8
Suppliersâ database
7 392
Lack of technical feasibility study
by suppliers
10 Request for quotation (RFQ) 7 490
Disruption in the
company planning
6 Lack of capacity feasibility study
by suppliers
10
Project managerâs point of view
9 630
Long geographical distance to the
suppliers
9
Project control, Project managerâs
point of view
2 126
Delay penalty (by
customers)
3 Not having suitable environment
for accurate measurement
2 Project managerâs point of view 10 140
Difficulty in providing accurate
measurement and special control
tools
8 Quality Dept. 9 504
Reduction in sales 6 Lake of a base time 9 Project managerâs point of view 10 630
Step 1- Conducting FMEA for the CTQ under study (outsourcing process time, which is divided into
3 independent CTQs): To calculate risk priority number for potential defect causes in order to
facilitate the analysis phase and to have more concentration on potential causes with maximum RPN.
In fact, using FMEA, data gathering activities focus on more critical input and process variables. For
example, table 5 lists part of FMEA table about delay time.
Step 2- Defining sample for the study domain and calculating sigma level: considering that sale
contracts generally include several âorder rowsâ; Each âorder rowâ contains specific lot size and
order delivery time (for example, a sale contract contains over 300 âorder rowâ). there are only a
limited number of main contracts of sale over a period of 3 years. Therefore, a sale contract was
chosen by champion and the project team. This contract was constituted of 177 separate âorder rowâ
(Table 6).
7. M. Cheshmberah and S. M. M. Nabavi / Uncertain Supply Chain Management 2 (2014) 121
Step 3- calculating sigma level of the process: this index was calculated as follows in table 6. Each
âorder rowâ has chosen as âfailure unitâ.
Table 6
Calculation of sigma levels of three sub-processes
177 Ă 100 = 17700
The number of potential failure opportunities
CTQ1
Calculation of sigma level
of âcontracting sub-processâ
17700
Total number of actual failure opportunities
1
Calculation of DPO
1,000,000
Calculation of DPMO
0.0
Calculation of sigma level (by standard tables)
59 Ă 100 = 5900
The number of potential failure opportunities
CTQ2
Calculation of sigma level
of âsupply sub-processâ
2630
Total number of actual failure opportunities
0.438333
Calculation of DPO
438333
Calculation of DPMO
1.6552
Calculation of sigma level (by standard tables)
17 Ă 100 = 1700
The number of potential failure opportunities
CTQ3
Calculation of sigma level
of âdelivery sub-processâ
1112
Total number of actual failure opportunities
0.654117
Calculation of DPO
654117
Calculation of DPMO
1.12
Calculation of sigma level (by standard tables)
Step 4- Detailed drawing of the process based on breaking up to the three sub-processes: in order to
have better chance of analyzing and according to the determined Sigma level for each sub-process,
we need to plot the process in more details.
Step 5- Determining bottlenecks: it is essential in this section to define time bottlenecks discuss more
in analysis phase. Considering the three separate CTQs (contracting sub-process, supply sub-process,
and delivery sub process), it was decided to conduct separate sampling for each CTQ after gathering
information about the sample wholesaler contract.
Moreover, according to the consultant (master black belt) and the teamâs decision 20 samples adopted
for each CTQ. This was because there is no limitation to get more than 20 samples for CTQ1
(contracting) and CTQ2 (supply), while only 20 articles of delivery CTQ had been fulfilled. In other
words, 20 random samples for CTQ1 and CTQ2 and all fulfilled delivery cases were chosen and time
bottlenecks were determined based on the average period of samples.
5. Analysis Phase
The problem is investigated more thoroughly in this phase especially by studying time bottlenecks by
utilizing proper tools, root causes of the problem are identified. In fact, having root causes identified,
the conditions for presenting the appropriate solutions and preventing causes of the problem in the
next phase (Improvement phase) are provided. Followings are different steps of the analysis phase:
Step 1- Holding brain storm meetings and utilizing cause and effect analysis tools (fish bone) and
Pareto analysis for CTQ1 (contracting), and CTQ3 (delivery); because these two sub-processes are
completely in the functional area of the company.
Step 2- Depicting flow-chart and value analyzing of each of the three sub-processes to have better
distinction between âvalue addedâ and ânon-value addedâ operations.
Step 3- Interviewing suppliers: four suppliers were chosen; of which two suppliers had the highest
delivery delay and two ones had the lowest. This tool was particularly used for supply sub-process.
Finally, conducting the mentioned steps, lead to determining the root causes of delay in all 3 sub-
processes of contracting, supply and delivery. Table 7 lists the identified causes.
8. 122
Table 7
List of the identified root causes
No. Title No. Title
1 Weak assessment of staffsâ capacity 18 Inadequate training of the project managers and QC inspectors
2 Failing to assess suppliersâ capacity 19 Failing to conduct proper heat treatment on the part of suppliers
3 Technical weakness of the contractors 20
improper working environment for QC inspectors and project
managers and improper measurement environment
4 Insufficient identified contractors 21 Ineffective supplier evaluation system
5 Lack of technical feasibility study on the part of contractors 22 Incomplete quality control instructions
6 Lack of capacity feasibility study on the part of contractors 23 Lack of QC inspectors evaluation system
7 Geographical distance to the contractors 24 Lake of project managers evaluation system
8 Not having suitable environment for accurate measurement 25 Inaccurate calibration system
9 Difficulty in providing special control tools 26
Not taking quality standards into consideration (requirements of
contracts) by the project managers and producers
10 Lake of a base time 27 Lake of statistical quality control system
11 Administrative bureaucracy (complexity of the process) 28 Improper packaging and transportation
12 Poor contractor selection 29
Failing to define the exact specifications of product, design and
preparation of technical documents
13 Lack of documented process procedure 30 Low quality raw materials used by the suppliers
14 Inadequate staff expertise 31 Poor performance of QC inspectors
15
Failing to provide technical maps and documents for the
contractors in time
32 Unmotivated QC inspectors
16 Quality control system inefficiency (unitsâ interaction)
33
Not considering waiting time for quality control in production
planning by project managers
17
Evaluating staffs performance based on volume of the production
rather that quality of products
6. Improvement Phase
In this phase, appropriate and effective solutions for the identified root causes in the previous phase
are proposed, and then evaluated, selected and finally implemented. Overall, improvement phase can
be divided to three main parts of identifying solutions, prioritizing solutions and executing them.
Actually, Budget and time constraints and problem-solving capacity of the organization need to be
taken into consideration. Thus, necessarily first the more important causes must be taken into account
which are the Pareto analysis. By holding brain storm meetings and investigating possible solutions
for each root, a list of solutions were obtained (table 8); it got clear that the main part of the solutions
were common . Therefore, along with listing the mentioned solutions, they were prioritized in table
10. Following steps were taken in improvement phase:
1. Listing all possible solutions for the main identified roots
2. Refining and prioritizing the list of solutions based on determined
criteria
3. Initial planning and appointing implementation teams
4. Activities and resources planning
5. Time scheduling (Gantt Chart preparation)
6. Assigning tasks to the teams and defining action plan
7. Training the teams
8. Implementing solutions (activities) by the teams
9. Results evaluation
10. Troubleshooting and supplementary measures
Table 8
The list of solutions
No. Solution
1 Revising suppliersâ identifying, evaluating and choosing system
2 Preparing instructions for inquiring basic price and basic delivery time
3 Improving contracting process
4 Establishing suppliers information database
5 Improving QC procedures
6 Improving evaluation system
7 Developing the comprehensive project management system
8 Designing operational information database for all activities
9 Improving employeesâ motivation system
10 Quality policy review
11 Upgrading the existing suppliers
12 Ranking quality experts
13 Needs assessment and providing calibration system for inspection equipment
14 providing jobs standards
15 Codifying and executing training programs for the existing procedures
16 Strategy reconsideration
17 Standardization (localization) production technology
18 Establishing participatory management system
9. M. Cheshmberah and S. M. M. Nabavi / Uncertain Supply Chain Management 2 (2014) 123
Table 9 Table 10
Criteria for prioritizing the solutions High priority improvements
No. Title No. Title
A The managerâs priority 1 Improving outsourcing process
B Feasibility of project at the present time
2
Revising suppliersâ identifying, evaluating
and choosing system
C
Feasibility based on authorities and capabilities of
project team
3
Improving contracting format and process
D Coordination with Six Sigma project 4 improving suppliers information database
E Possibility of developing methods in other modules 5 Improving QC procedures
F Profitability
6
Revising data flow and designing operational
information database
G Effectiveness 7 Upgrading the existing suppliers
Each criteria is scored between 0 and 5 8 Developing the comprehensive project
management system
7. Control Phase
In this phase, improvement project team makes sure that the problem has been solved (removal or
neutralization of the main roots), solutions have been executed and the new proposed procedures have
been completely established. In other words, control phase is the monitoring and maintaining phase.
The followings measures were taken in this phase:
Step 1: Supervise execution of the solutions and making feedbacks,
Step 2: Document the whole procedure of defining and implementing of the improvement project,
Step 3: Document the experiences and the findings,
Step 4: Document conducted solution as standard procedures,
Step 5: Re-caluclate the Sigma level (sigma level of the contracting sub-process 0.7; supply sub-
process 1.9; delivery sub-process 1.4),
Step 6: Investigat and discussion for defining the next improvement project and targeted Sigma level.
8. Conclusion
In conclusion, the improvement project brought the firm, the employer, the executer, and the
executive team valuable lessons, including:
ï· At the beginning and before initiating the project, there were many doubts on whether it is a
correct approach to conduct the project using Six Sigma and DMAIC methodology, or by
using simpler methods like the seven-step problem solving traditional approach, desired
results would be achieved in a better, easier and faster way.
ï· Deeper investigations made it clear to the team that DMAIC methodology is a structured
problem solving methodology with a meaningful and coherent classification, leading to the
achievement to desired results and effective problem solving. On the other hand, using Six-
Sigma tools and techniques, should be highly selective and proportional to the conditions of
the problem.
ï· Commitment of senior managers to definition and implementation of an improvement project,
taking the position of employer and delegation of authority to a competent and influential
person as the project manager, are of necessities and prerequisites to meet the objectives of an
improvement project.
10. 124
ï· It is necessary to make sure of the correct definition of any improvement project before
execution.
ï· However, the logic of DMAIC methodology demands that project team reconsider definition
phase upon any ambiguity in definition, even in measurement or analysis phases.
ï· Before applying different methods of problem solving, it is needed to apply various methods
of problem finding to determine improvement opportunities correctly. Techniques such as
SPC, periodical/annual evaluation, organizational troubleshooting such as BSC, EFQM are
some proper techniques of problem finding.
ï· The project team definitely needs to take advantage of opinions and experiences of at least a
well-experienced master black belt level consultant.
ï· To have better results in improvement projects, we can proceed to develop a motivation
system (regulations) at the organizational level.
This project only considered the CTQ of delivery delay. First, it is possible to set goals for higher
Sigma level for this CTQ, other improvement projects can be defined. Second, other important issues
like quality, necessity of reducing non-conforming lots and reducing the prices can be taken into
consideration to continue the outsourcing process improvement and to define the future improvement
projects.
References
Basu, R., & Wright, N. (2003). Quality Beyond Six Sigma. Butterworth-Heinemann.
Cheshmberah, M., Makui, A., Seyedhosseini, S., & Najmi, A. (2011). A new fuzzy MCDA
framework for make-or-buy decisions: A case study of aerospace industry. Management Science
Letters, 1(3), 323-330.
Ho, Y. C., Chang, O. C., & Wang, W. B. (2008). An empirical study of key success factors for Six
Sigma Green Belt projects at an Asian MRO company. Journal of Air Transport
Management, 14(5), 263-269.
Jennings, D. (1997). Strategic guidelines for outsourcing decisions. Strategic Change, 6(2), 85-96.
Karadbhuje, S. W., Deshpande, S. B., & Gorde, M. S. (2012). Six sigma qualities in business.
International Journal of Engineering and Innovative Technology, 1(4), 285-290.
Kremic, T., Tukel, O. I., & Rom, W. O. (2006). Outsourcing decision support: a survey of benefits,
risks, and decision factors. Supply Chain Management: an international journal, 11(6), 467-482.
Kumar, U. D., Nowicki, D., RamĂrez-MĂĄrquez, J. E., & Verma, D. (2008). On the optimal selection
of process alternatives in a Six Sigma implementation. International Journal of Production
Economics, 111(2), 456-467.
Kwak, Y. H., & Anbari, F. T. (2006). Benefits, obstacles, and future of six sigma
approach. Technovation, 26(5), 708-715.
Pyzdek, T. (2003). The six sigma project planner. A Step by Step Guide to Leading a Six Sigma
Project Through DMAIC.
Schroeder, R. G., Linderman, K., Liedtke, C., & Choo, A. S. (2008). Six Sigma: definition and
underlying theory. Journal of operations Management, 26(4), 536-554.