Alcatel Lucnet bts offline commissioning

1. Presented by ENG: Ahmed Mohammed Nabieh
Supervised by ENG : Amr Abd Elkreem
Alcatel Lucent BTS
Offline & Commissioning

2. Introduction

3. The BTS commissioning & SW files are stored on the station unit module
(SUMA)
The Station unit module is the core of the BTS ,it is responsible for
• The O&M Functions such as Alarms reporting ,BTS Configuration,
internal Power Supply control & clock generation and distribution
• Transmission functions by connecting the BTS to the BSC through the
ABIS cable.
The ABIS can carry up to 32 time slots
• 0 to 30 are assigned to the TRES for normal traffic(voice and Data
services)
• 31 : is assigned to the OMU in the SUMA card for signaling (Control
information) between BSC & BTS such as Alarm reporting ,BTS
Master file Download, configuration files etc..

4. LED Color Status Description
OML Yellow On BTS is supervised and connected to the BSC
Blinking BTS & BSC link is being established
Off Link disconnected.
ABIS Yellow On Abis 1 is connected and can serve TCH/Signaling
Blinking There are Alarms on the ABIS
Off Not configured or not used.
O&M Yellow On SUMA master file & configuration are present in the
EPROM
Blinking In a transient state, SUMA is loading the BTS MSF &
Configuration file from the BSC
Off Not used.
FAUL
T
RED On Fatal alarm on BTS Module (ANC,TRE etc ..)
Blinking Non-fatal alarm. Such as Faulty Fan unit
Off No alarm.
SUMA card led status indication

5. Offline

6. • Switch the BTS off by pushing down its DC C/BS

7. • Unscrew the ABIS Cable

8. • Open BTS SW and Type
User Name : commte
Password : bts2site

9. • Go to Configuration Click On BTS Software Download

10. • Press the folder icon to start choosing the BTS Files

11. • Select Master File from the BTS SW folder

12. • Select 0CPF File from the BTS SW folder

13. • Wait for the BTS to download all the files ,During the SW
Download the Suma LED Status will be :
OML ,ABIS & O&M Flashing
last file to be downloaded is the OCPF 002 file after that the O&M
will be solid

14. Commissioning

15. • From Configuration choose BTS Commissioning

16. • Click on Start Commissioning

17. • Notice that the status of the commissioning changed from not
running to running

18. • Edit Q1 address by clicking its start button

19. • Edit Remote Inventory by clicking its start button and press
YES : if the update is already done in the Remote Inventory
panels
NO : if the update is not done in the Remote Inventory panels

20. • Edit Sector Mapping by clicking its start button
Assign sector-ID to each combiner and then press ok

21. • Edit Twin-Settings by clicking its start button
Choose the mode of each Twin-TRE , usually in our network
we leave at the default which is Dual TRE

22. • Hardware check by clicking its start button
the Suma card will start to check the HW available inside
the BTS through the RI-Cable

23. • INIT _ALL_SECT by clicking its start button
the SUMA card will power on all the combiners and TRES to
check their operation

24. Choose End commissioning ,Stop commissioning window will appear
choose ok after moving all the modules in the selected module window
Wait for the BTS to restart itself SW and then connect the Abis cable.

25. • Finally restart the BTS HW
the SUMA led status should be as following :
Abis & OML are solid
O&M Flashing as the BTS loading its data and RSLs from the BSC

26. • The loading process will take 15 to 20 Minutes ,after that the
O&M Led will be solid and the SUMA will initialize the
BTS sectors (Combiners & TRES)

27. • The BTS Terminal program will start to load the BTS Data
Take snapshots and check with OMC

28. Thank You