1. Bts commissioning (alcatel lucent)Presentation Transcript
1. Switch OFF the BTS cabinet and disconnect Abis connectors fromDDF before
offline start
2. Disconnect the Abis connectorfrom The DDF
3. Switch ON the BTS cabinet breakers and connect the Laptop with BTS
4. User Name “COMMTE” Password“COMMTE”
5. Communication Port setting
6. OR
7. After connecting this windowwill be appear
8. Go toConfiguration-> BTS-SW Download-> to download BTS software
9. After BTS- SW downloadthis window will appear
10. Go to offlineFiles and select First File of Master File.
11. Go to offlineFiles and select First File of DDL file.
12. Click ok to startdownloading SW
13. BTS software starts to download.
14. All these Files aredownloaded
15. Go toConfiguration BTScommissioning
16. Click startcommissioning
17. Edit Qmux Address
18. Edit sector Mapping
19. Check AllTwin TRE’s.
20. Click EndCommissioning Click << arrow to move selected modules to available
modules
21. All modules Shifted to update modules.
22. Click No to end
23. Reconnect theAbis connector at DDF by verifyingthe TX/RX cables properly
24. Give Hard Reset to BTS cabinet as theOML has established to put the site on
Downloading.
25. OFF Line Commissioning Completed Successfully.
26. BTS ON-Line commissioning Procedure using B10 Go toconfiguration>>
Hardware setting>>BeginHW modification
27. Go to configuration> BTS commissioning Go to start commissioning> Edit
Q1Address, Edit SectorMapping and Twin TRA setting as in offline.
28. Go toconfiguration> Hardware setting>“EndModification” to end
onlinecommissioning
29. Online commissioning steps Connect the Abis connector at DDF by verifying
Tx/Rx cable properly. OML will be established after primary Abis has connected to
DDF. Give hard reset to BTS after OML has established. Put site on Downloading
from OMC. O&M will be established as downloading completes. Connect Laptop
to BTS MMI port. Go to configuration>Hardware setting>Begin Hardware
modification.
30. Online commissioning steps Go to configuration>BTS commissioning>start
commissioning. Edit Qmux Address Edit sector mapping Check all Twin TRA
setting. Click end commissioning and shift all modules from selected modules to
available modules. Go to configuration>Hardware setting>End Hardware
modification. Click “yes” when an automatically hardware modification window
appears. Hw Audit will be run and all Hardware will be shown after sometime.
31. ON Line Commissioning Completed Successfully.

2. 32. Software components combiner Fan UnitHardwareShown insoftware window
Tre’s clock Alarm card
33. Alarmswindow
34. Transceivers Shown in window
35. Transceivers Types Four type of Transceivers in Alcatel Equipment
TRAGE>Gsm Single TRE TRADE>Dcs single TRE TGT09>Gsm Twin TRE
TGT18>DCS Twin TRE TAGHE>High power TRE
36. VSWRShown in window
37. Sectors ShownIn window
38. Station units
39. BSC SBLs(security block levels)BTS OM & Sectors.Sec RSLs can be unlock
from local Terminal.
40. Troubleshooting If a TRE or combiner is in “Not Operational” or “FOS” state
then disable it then initialize it by using “init” command. If TRE or combiner can not
operational by doing above command then remove it by using the following method.
Go to configuration>>Hardware setting>>Begin HW modification. Go to
Configuration>>Hardware setting>>Remove. Remove the Hardware from BTS.
Window will be appear of Hardware removal, select the module to remove. Go to
Configuration>>Hardware setting>>End Modification. Click ”yes” when
configuration changes window appears.
41. HardwareRemoval Method Step:1
42. HardwareRemoval Step:2
43. HardwareRemoval Step:3
44. Troubleshooting cont.. When a module goes in “FOS” state then it must be
disable by using ”disable” command before initializing it by using “init” command
otherwise it will not goes to operational state. When a module is in “Not
Operational” state with color white then it means it has not got it’s RSL number still.
Reload BTS data by going to “configuration>Reload Bts data” or using a method of
“Begin Hardware then End Hardware” as discussed earlier. It will take some time to
become operational. When a module is in “MSD” or “MSA” state then it will not get
any command because its maintenance has seized for a while. When TRE RSL has
locked then then its RSL will not be stable, so unlock the TRE from OMC.
45. Troubleshooting cont.. Sometime there is some faulty hardware in Bts that’s why
other sectors or TRE’s can effect and can not work properly. Due to these faulty
hardware other sectors or TRE’s can be down so simply remove this hardware. By this
method other hardware become in operational state. Some time “SUMA” can not
work properly that’s why whole Bts effects so change the slot of “SUMA” and give
hard reset to Bts. If modules in a shelf can not powers up then check it’s power cable
at the back ports of Bts or check it “RI” cable. Also check the power switch for the
concern shelf. If a “EACB” card is Not operational or “FIT” state then initialize it
from software. If it again goes in “FIT” state then Alarm card is faulty.
46. Troubleshooting cont.. Some time Primary Abis is stable by showing LED on
Suma card but OML can not become stable, It means that Abis LED is fake. So check
the Tx/Rx cable from both Bts end and microwave end and make sure that it is
correctly connected. Also check Tx/Rx patching on DDF by using LED. Make sure
that LED blinks on every pair on DDF. Also check the BNC and Abis connectors.
Abis cable which is connected from Suma card to Bts board can be faulty so also
verify it. If a TRE or combiner can not operational than change its slot then verify
it. Vswr issues can be resolved by checking connectors from Bts end and feeder

3. end. The last option for Alcatel equipment to become operational is the “Hard reset
of Bts”.
47. External Alarms of MBO2
48. ALCATEL GLOSSARY AAN Antenna Network BBCB BTS Control BusBSII
Base Station ControllerBSS Base Station SubsystemBTS Base Station
TransceiverBTSW BTS-Terminal for Windows CCCF Cabinet Cooling FanCDM
Configuration Data MessageCLEI Common Language EquipmentCLLK Clock
LinkCPF Configuration Parameter FileCRC Cyclic Redundancy CheckCU Carrier
Unit
49. ALCATEL GLOSSARY DDC Direct CurrentDMA Deferred Maintenance Alarm
EEQU Equipped FFIA Format Identifier for Application part of RIFIM Format
Identifier ManufacturingFIT Faulty In TrafficFLT FaultyFOS Faulty Out of
ServiceICS Item Change StatusIT In Traffic LLDA Local Defence ActionLRA Local
Recovery Action MMI Maintenance InformationMSA MSD AutoMSD Maintenance
Seized
50. ALCATEL GLOSSARY NNEQ Not EquippedNOP Not Operational OO&M
Operation and MaintenanceOMU Operation and Maintenance UnitOMUA OMU A
RITOMUB OMU B RITOP OperationalOPR Operator PPADD Physical
AddressPMA Prompt Maintenance
51. ALCATEL GLOSSARY RRA Radio AccessRF Radio FrequencyRFH Radio
Frequency Hopping ( also known as : Synthesizer Hopping )RI Remote InventoryRIT
Replaceable ItemRX Receiver or receive .....RTC Remote Tunable Combiner SSBL
Security Block LevelSCFE Station Unit Control Function Entity RITSOS System Out
of ServiceSUM Station Unit ModuleSUMP SUM PCM RITSW Software
52. ALCATEL GLOSSARY SSBL Security Block LevelSCFE Station Unit Control
Function Entity RITSOS System Out of ServiceSUM Station Unit ModuleSUMP
SUM PCM RITSW Software TTLV Tag, Length, ValueTRE Transceiver Module
(combined Transmitter / Receiver functionality for base band and RF signals)TS
TimeslotTX Transmitter or transmit . VVPMA Very Prompt Maintenance
AlarmVSWR Voltage Standing Wave Ratio
53. ALCATEL GLOSSARY WWBC Wide Band CombinerWTC Wait Traffic Clear
XXBCB External BCBXCLK External ClockXIOB External Input Output Board