This document provides an overview of a 3-unit fluid mechanics course. It covers topics like fluid properties, fluid statics, pressure measurement, forces on submerged surfaces, buoyancy, and fluid flow. The course synopsis outlines concepts like density, pressure, viscosity, hydrostatic forces, and fluid flow measurements. It also defines key terms such as streamlines, boundary layers, and discharge. The document serves as an introduction to the main principles and concepts covered in the fluid mechanics course.
Harnessing WebAssembly for Real-time Stateless Streaming PipelinesChristina Lin
Traditionally, dealing with real-time data pipelines has involved significant overhead, even for straightforward tasks like data transformation or masking. However, in this talk, we’ll venture into the dynamic realm of WebAssembly (WASM) and discover how it can revolutionize the creation of stateless streaming pipelines within a Kafka (Redpanda) broker. These pipelines are adept at managing low-latency, high-data-volume scenarios.
NUMERICAL SIMULATIONS OF HEAT AND MASS TRANSFER IN CONDENSING HEAT EXCHANGERS...ssuser7dcef0
Power plants release a large amount of water vapor into the
atmosphere through the stack. The flue gas can be a potential
source for obtaining much needed cooling water for a power
plant. If a power plant could recover and reuse a portion of this
moisture, it could reduce its total cooling water intake
requirement. One of the most practical way to recover water
from flue gas is to use a condensing heat exchanger. The power
plant could also recover latent heat due to condensation as well
as sensible heat due to lowering the flue gas exit temperature.
Additionally, harmful acids released from the stack can be
reduced in a condensing heat exchanger by acid condensation. reduced in a condensing heat exchanger by acid condensation.
Condensation of vapors in flue gas is a complicated
phenomenon since heat and mass transfer of water vapor and
various acids simultaneously occur in the presence of noncondensable
gases such as nitrogen and oxygen. Design of a
condenser depends on the knowledge and understanding of the
heat and mass transfer processes. A computer program for
numerical simulations of water (H2O) and sulfuric acid (H2SO4)
condensation in a flue gas condensing heat exchanger was
developed using MATLAB. Governing equations based on
mass and energy balances for the system were derived to
predict variables such as flue gas exit temperature, cooling
water outlet temperature, mole fraction and condensation rates
of water and sulfuric acid vapors. The equations were solved
using an iterative solution technique with calculations of heat
and mass transfer coefficients and physical properties.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Student information management system project report ii.pdf
470_MCE 205.ppt
1. MCE 205
FLUID MECHANICS I
(3 UNITS)
PREPARED BY
BUKOLA O. BOLAJI Ph.D
DEPARTMENT OF MECHANICAL ENGINEERING,
UNIVERSITY OF AGRICULTURE, ABEOKUTA
OGUN STATE, NIGERIA
1
2. FLUID MECHANICS I (3 UNITS)
COURSE SYNOPSIS
• Elements of fluid statics, density, pressure,
surface tension, viscosity, compressibility etc.
hydrostatic forces on submerged surfaces due
to incompressible fluid. Static forces on surface
stability of floating bodies.
• Introduction to fluid dynamics – conservation
laws. Introduction to viscous flows. Fluid
friction, friction factor and its relation to pipe
losses; pipes in parallel and series. Fluid flow
measurements, venturi meter. 2
3. 1.0 INTRODUCTION
Fluid Mechanics is a branch of applied
mechanics concerned mainly with the study
of the behaviour of fluids either at rest or in
motion.
Fluid: A fluid is a material substance, which
cannot sustain shear stress when it is at
rest. In other words, a fluid is a substance,
which deforms continuously under the
action of shearing forces, however small
they may be. 3
4. The major differences between liquids
and gases are:
• Liquids are practically incompressible
whereas gases are compressible
• Liquids occupy definite volumes and
have free surfaces whereas a given
mass of gas expands until it occupies
all portions of any containing vessel.
4
5. PROPERTIES OF FLUIDS
DENSITY
• The density or mass density of the fluid () is
defined as the mass per unit volume. Its unit of
measurement is kg/m3 i.e.
• = m/V. (1.1)
SPECIFIC VOLUME
• Specific volume is defined as volume per unit
mass. Its unit of measurement is (m3kg– 1)
(1.2)
5
6. SPECIFIC WEIGHT
• The specific weight ‘Y’, of a fluid is its
weight per unit volume. Unit is N/m3.
• Y = mg/V = g (1.3)
RELATIVE DENSITY
• The relative density RD or specific gravity
of a substance is mass of the substance
to the mass of equal volume of water at
specified temperature and pressure.
• (1.4)
6
7. COMPRESSIBILITY OF FLUIDS
• The compressibility of any substance is measure
in terms of bulk modulus of elasticity, K.
BULK MODULUS OF ELASTICITY
• Also known as Modulus of volume expansion is
defined as the ratio of the change in pressure to
the corresponding volumetric strain.
• (1.5)
or
• (1.6)
7
8. VISCOSITY OF FLUIDS
• The viscosity of a fluid is that property which
determines its ability to resist shearing stress or
angular deformation.
• shear stress, , varies with velocity gradient,
du/dy.
• (1.7)
• The Dynamic viscosity, is defined as the shear
force per unit area required to draw one layer
of fluid with unity velocity past another layer
unit distance away from it in the fluid. Unit is
Ns/m2. 8
9. KINEMATIC VISCOSITY
• Kinematic viscosity, is defined as the ratio of dynamic
viscosity to mass density. Unit is m2s – 1
• = / (1.8)
NEWTONIAN AND NON-NEWTONIAN FLUIDS
• Ideal Fluid: For the ideal fluid, the resistance to shearing
deformation is zero, and hence the plotting coincides
with the x-axis.
• Ideal or Elastic Solid: For the ideal or elastic solid, no
deformation will occur under any loading condition, and
the plotting coincides with y-axis.
• Newtonian Fluids: Fluids obeying Newton’s law of
viscosity and for which has a constant value.
• Non-Newtonian Fluids: These are fluids which do not
obey Newton’s law of viscosity. 9
10. SURFACE TENSION
• The surface tension, , is defined as the force in
the liquid normal to a line of unit length drawn
in the surface. Its unit of measurement is N/m.
CAPILLARITY
• Another interesting consequence of surface
tension is the capillary effect, which is the rise
and fall of a liquid in a small-diameter tube
inserted into the liquid.
• The height of liquid rise (h) is obtained as:
• (1.9)
10
11. FLUID PRESSURE
• Pressure is express as the force per unit area.
• P = F/A. (Nm– 2) (1.10)
• Atmospheric Pressure: This is the pressure due to
the atmosphere at the earth surface as measured
by a barometer. Pressure decreases with altitude
• Gauge Pressure: This is the intensity of pressure
measured above or below the atmospheric
pressure.
• Absolute Pressure: This is the summation of
Gauge and atmospheric pressure.
• Vacuum: A perfect vacuum is a completely empty
space, therefore, the pressure is zero. 11
12. 2.0 FLUID STATICS
• Fluid statics or hydrostatics is the study of
force and pressure in a fluid at rest with no
relative motion between fluid layers.
• From the definition of a fluid, there will be no
shearing forces acting and therefore, all forces
exerted between the fluid and a solid
boundary must act at right angles to the
boundary.
• If the boundary is curved, it can be considered
to be composed of a series of chords on which
a force acts perpendicular to the surface
concerned.
12
13. TRANSMISSION OF FLUID PRESSURE
• The principle of transmission of fluid pressure
states that the pressure intensity at any point
in a fluid at rest is transmitted without loss to
all other points in the fluid.
PRESSURE DUE TO FLUID’S WEIGHT
Fluids of Uniform Density
• Total weight of fluid (W) = mg
W = gAh (2.1)
• Pressure (P) = Weight of fluid/Area
P = gh (2.2)
13
14. STRATIFIED FLUIDS
• Stratified fluids are two or more fluids of
different densities, which float on the top
of one another without mixing together.
• P1 = 1gh1 and W1 = 1gh1A.
• P2 = 2gh2 and W2 = 2gh2A.
• Total pressure, PT = 1gh1 + 2gh2
• Total weight, WT = (1gh1 + 2gh2)A
WT = PTA (2.4)
14
15. PRESSURE MEASUREMENT BY MANOMETER
Measurement of Absolute Pressure
• The absolute pressure of a liquid
is measured by a barometer.
P = gh (2.5)
Piezometer Tube
• Piezometer consists of a single vertical
tube, inserted into a pipe or vessel
containing liquid under pressure which
rises in the tube to a height depending on
the pressure. The pressure due to column
of liquid of height h is:
P = gh (2.6) 15
16. • OPEN–END U-TUBE MANOMETER
• Pressure PB = PA + gh1
• Pressure PC = 0 + mgh2
• PA + gh1 = mgh2 (Since PB = PC)
PA = mgh2 – gh1 (2.7)
16
17. CLOSE-END U-TUBE MANOMETER
• PC = PA + A gh1
• PD = PB + Bgh2 + mgh
But PC = PD, hence,
• PA + Agh1 = PB + Bgh2 + mgh
PA – PB = PBgh2 + mgh – Agh1 (2.8)
17
18. INVERTED U-TUBE MANOMETER
• PA = A gh1 + mgh + PC
• PB = Bgh2 + PD
• Since PC = PD
PA – PB = Agh1 + mgh – Bgh2 (2.9)
• If the top of the tube is filled with air
PA – PB = Agh1 – Bgh2 (2.10)
• If fluids in A and B are the same
PA – PB = pg(h1 – h2) + mgh (2.11)
• Combining conditions for Eqs. (2.10) and (2.11):
PA – PB = pg(h1 – h2) (2.12) 18
19. 3.0 FORCES ON SUBMERGED SURFACES
A submerged surface can be defined as a
surface of a body below the liquid surface.
There are two types of surfaces, namely:
• Plane surface
• Curved surface
SUBMERGED HORIZONTAL PLANE SURFACE
P = gh (3.1)
F = ghA (3.2)
19
20. SUBMERGED VERTICAL PLANE SURFACE
• Elemental force,
dF = PdA
dF = g ydA
But ydA is the first moment of area
about the liquid surface, hence
F = gAyG (3.3)
20
21. DETERMINATION OF CENTRE OF PRESSURE (yp)
21
dF = gydA
Taking moment about the liquid surface
dF.y = gy2dA and dF.y = g y2dA
But the y2dA is the second moment of
area I, about the surface level
Fyp = g y2dA = gI (3.4)
y p = I/AyG = Ratio of Second moment of
Area to First moment of Area
22. Using parallel axis theorem,
IX = IG + Ay2
I = IG + Ay2
G (3.5)
IG is the second moment of Area about
the centroid. Substituting for I, we
have
(3.6)
22
23. GEOMETRIC PROPERTIES OF SOME SHAPES
• Rectangle
A = bd
IG = bd3/12
• Triangle
A = ½ bh
IG = bh3/36
• Circle
A = R2 and IG = R4/4
• Semicircle
A = ½ R2
IG = 0.1102R4
23
24. QUESTION
A fuel tank 10 m wide by 5 m deep contains
oil of relative density 0.7. In one vertical side
a circular opening 1.8 m in diameter was
made and closed by a trap door hinged at the
lower end B held by a bolt at the upper end
A. If the fuel level is 1.8 m above the top edge
of the opening, calculate the:
• total force on the door
• force on the bolt
• force on the hinge. 24
25. SUBMERGED INCLINED PLANE SURFACE
dF = PdA
P = gy & y = x.sin
P = gx.sin
dF = gxsin.dA (3.7)
dF = g.sin x.dA
where x.dA = AxG first moment of area.
F = g sin AxG
F = gyGA (3.8)
25
26. DETERMINATION OF CENTRE OF PRESSURE
Taking moment about the fluid surface,
dM = xdF dM = gx2sindA
dM = g.sin x2dA
I = x2dA (second moment of area), hence
M = g.sin I.
Also the total moment M = FxP, therefore,
FxP = g.sin I.
(3.9)
(3.10)
26
27. FORCES ON A SUBMERGED CURVED SURFACE
27
Determine the forces
acting on horizontal (FH)
and vertical (FV) planes.
These components are
combined into a
resultant force (R)
FH = g x Area of EA x depth to centroid of EA
FH = gAyG (3.11)
Vertical component FV is equal to the weight of
fluid which would occupy ECABD
FV = Gv (3.12)
28. 4.0 BUOYANCY AND STABILITY OF
FLOATING BODIES
BUOYANCY
• The Upthrust (upward vertical force due to
the fluid) or buoyancy of an immersed body is
equal to the weight of liquid displaced
• The centre of gravity of the displaced liquid is
called the centre of buoyancy.
• Volume of fluid displaced is:
(4.1)
28
29. STABILITY OF A SUBMERGED BODY
• For stable equilibrium the centre of gravity of
the body must lie directly below the centre of
buoyancy of the displaced liquid.
• If the two points coincide, the submerged
body is in neutral equilibrium for all positions.
STABILITY OF FLOATING BODIES
29
30. The point M is called the metacentre
• Equilibrium is stable if M lies above G
• Equilibrium is unstable if M lies below G
• If M coincides with G, the body is in neutral
equilibrium.
• Metacentre: The metacentre is the point at
which the line of action of upthrust (or
buoyant force) for the displaced position
intercept the original Vertical axis through the
centre of gravity of the body.
• Metacentric Height: The distance of
metacentre from the centre of gravity of the
body is called metacentric height.
30
31. DETERMINATION OF POSITION OF
METACENTRE
• Consider an elemental
horizontal area dA
h = x.tan
dW = gh.dA = gx tan.dA
Taking moment about axis OO
dM = x.dW = g.x2tan.dA
Total moment, M = dM = gtan x2dA
Where x2dA = I = second moment of area
Therefore, M = gtan.I (4.2) 31
32. • The Buoyance Moment
Buoyance Moment, MB = R.BB’
Buoyant force R = gV
but BB’ = BM.sin, therefore,
MB = gV.BMsin (4.3)
Equating Eqs. 4.2 and 4.3, we have
gtan.I = gV.BMsin
(for very small angle) (4.4)
The distance BM = Metacentric Radius
But GM = BM – BG = (I/V) – BG (4.5)
• GM = Metacentric Height 32
33. QUESTION 4.1
A stone weighs 400 N in air, and when immersed in
water it weighs 222 N. Compute the volume of the
stone and its relative density.
• Hints (i) V= R/g (ii) RD = W/R
QUESTION 4.2
A pontoon is 6m long, 3m wide 3m deep, and the
total weight is 260 kN. Find the position of the
metacentre for rolling in sea water. How high may
the centre of gravity be raised so that the pontoon
is in neutral equilibrium? (Take density of sea
water to be 1025 kgm– 3) 33
34. 5.0 FLUID FLOW AND EQUATION
• Boundary Layer: The layer of fluid in the
immediate neighbourhood of an actual flow
boundary that has had its velocity relative to
the boundary affected by viscous shear is
called the boundary layer.
• Adiabatic Flow: Adiabatic flow is that flow
of a fluid in which no heat is transferred to
or from the fluid. Reversible adiabatic
(frictionless adiabatic) flow is called
isentropic flow. 34
35. • Streamline: A streamline is a continuous
line drawn through the fluid so that it has
the direction of the velocity vector at every
point.
35
• Stream Tube: A stream tube is the tube
made by all the streamlines passing
through a small, closed curve
36. 36
• Volumetric Flow rate or Discharge (Q): It is
defined as the volume of fluid passing a given
cross-section in unit time (m3s– 1).
• Mass Flow Rate (m): It is defined as the mass of
fluid passing a given cross-section in unit time
(kgs– 1).
• Mean Velocity: At any cross-section area, it is the
ratio of volumetric flow rate to the cross-
sectional area.
• The Law of Conservation of Mass: The law of
conservation of mass states that the mass within
a system remains constant with time
disregarding relativity effects, dm/dt = 0.
37. Control Volume: A control volume refers to a region
in space and is useful in the analysis of situations
where flow occurs into and out of the space.
• The boundary of a control volume is its control
surface.
• The content of the control volume is called the
system
Continuity Equation: State that the time rate of
increase of mass within a control volume is just
equal to the net rate of mass inflow to the control
volume.
Q = v1A1 = v2A2 37
38. ENERGY EQUATION FOR AN IDEAL FLUID FLOW
Consider an elemental stream tube in motion
• F = Pressure x Area= PA
• divide through by g, and dv2 = 2vdv:
• This equation is called Euler equation of motion
38
ds
dv
dt
ds
dt
dv
ds
dv
v
dt
dv
since
dt
dv
dAds
gdAds
dA
dP
P
PdA
cos
dt
dv
ds
gds
dP
cos
39. BERNOULLI’S EQUATION
Bermnoulli’s theorem states that the total energy of
all points along a steady continuous stream line of
an ideal incompressible fluid flow is constant
although its division between the three forms of
energy may vary
• integration of the Euler equation gives:
therefore,
The 1st term z = the potential head of the liquid.
The 2nd term P/g = the pressure head
The 3rd term v2/2g = the velocity head. 39
40. TOTAL HEAD
Total head = potential head + Pressure head + Velocity
head
• Potential Head (z): is the potential energy per
unit weight of fluid with respect to an arbitrary
datum of the fluid. z is in JN– 1 or m
• Pressure Head (P/g): Pressure head is the
pressure energy per unit weight of fluid. It
represents the work done in pushing a body of
fluid by fluid pressure. P/g is in JN– 1 or m.
• Velocity Head (v2/2g): Velocity head is the kinetic
energy per unit weight of fluid in JN– 1 or m.
40
41. ENERGY LOSSES AND GAINS IN A PIPELINE
• Energy could be supplied by introducing a pump
• Energy could be lost by doing work against friction
Expanded Bernoulli’s Equation:
• h = loss per unit weight;
• w = work done per unit weight;
• q = energy supplied per unit weight
THE POWER OF A STREAM OF FLUID
• Weight per unit time = gQ (Ns– 1)
• Power = Energy per unit time
• Power = (weight/unit time) x (energy/unit weight)
• Power = gQH 41
42. QUESTION 5.1
A siphon has a uniform circular bore of 75 mm
diameter and consists of a bent pipe with its crest 1.8
m above water level discharging into the atmosphere
at a level 3.6 m below water level. Find the velocity of
flow, the discharge and the absolute pressure at crest
level if the atmospheric pressure is equivalent to 10 m
of water. Neglect losses due to friction.
QUESTION 5.2
A pipe carrying water tapers from 160 mm diameter at
A to 80 mm diameter at B. Point A is 3 m above B. The
pressure in the pipe is 100 kN/ at A and 20 kN/m2 at B,
both measured above atmosphere. The flow is 4
m3/min and is in direction A to B. Find the loss of
energy, expressed as a head of water, between points
A and B.
42
43. 6.0 FLOW MEASURING DEVICES
PITOT TUBE
H + v2/2g = H +h
v2/2g = h or
PITOT-STATIC TUBE
Pitot tubes may be used in the following area:
• they can be used to measure the velocity of liquid in
an open channel or in a pipe.
• they can be used to measure gas velocity if the
velocity is sufficiently low so that the density may be
considered constant.
• they can also be used to determine the velocities of
aircraft and ships. 43
44. VENTURI METER
A1v1 = A2v2 or v2 = (A1/A2)v1
• z1 = z2 (Horizontal)
Let Pressure difference
hence
and
44
45. • ORIFICE METER
• In an orifice meter, a pressure differential is
created along the flow by providing a sudden
constriction in the pipeline.
• The principles of operation is the same with
that of Venturi meter, except that it has lower
coefficient of discharge due the sudden
contraction. 45
46. REFERENCES
• Bolaji, B.O. 2008. Introduction to Fluid Mechanics. Ed.,
Adeksor Nig. Ent. ISBN: 978-33146-9-6, Nigeria.
• Douglas, J.F., Gasiorek and Swaffield, 1985. Fluid
Mechanics. Addison Wesley Longman Ltd., England.
• Fox, R.W. and McDonald, A.T. 1999. Introduction to
Fluid Mechanics. John Wiley and Sons, New York.
• Kreith, F. and Berger, S.A. 1999. Mechanical
Engineering Handbook. Boca Raton: CRC Press, LLC.
• Trefethen, L. 1972. Surface Tension in Fluid Mechanics:
In Illustrated Experiments in Fluid Mechanics. The MIT
Press, Cambridge, MA.
• Yaws, C.L. 1994. Handbook of Viscosity. Gulf, Houston.
46