1.5 layer forming farbics by HENAN BEYNOST TEXTILE TECHNOLOGY CO., LTD.
•
0 likes•85 views
The document describes a 1.5 layer polyester forming fabric from Henan Beynost Textile Technology Co. Ltd. for use in papermaking. The fabric has strong dewatering performance, excellent fiber support and formation, no fabric marking, and is very durable and resistant to wear. It is made of 100% polyester with specific warp and weft diameters and densities, and has strengths of 1000N/cm on the surface and a CFM of 530.
Report
Share
Report
Share
Download to read offline
Recommended
Recyclability of Spray Coated Smooth Nanocellulose films as a potential susta...
Recyclability of Spray Coated Smooth Nanocellulose films as a potential susta...Kirubanandan Shanmugam
Synthetic packaging materials are neither reprocessable, renewable nor biodegradable barrier and also difficult to recycle into useful products. While cellulose-based packaging is widely known as a renewable, reprocessable, recyclable and biodegradable material it has limited air and water vapour barrier properties. Nanocellulose (NC) has the potential to become a renewable alternative to plastic packaging barrier layers but its recyclability has not been reported. This investigation is focused on the production of spray-coated nanocellulose (NC) films and its recyclability via dispersion in water and vacuum filtration to form sheets again. Physical properties such as barrier performance and strength of NC films have been evaluated pre- and post- recycling. The recycled films retained 80% of tensile strength and significant barrier performance although the H2O vapour permeability (WVP) approximately doubled, increasing to 9.83 x 10-11 g.m-1.s-1 Pa-1, providing comparable values with for most synthetic packaging. SEM micrographs reveal no fibre agglomeration at the micro level and no damage to the fibres during recycling. The retained strength and barrier properties and facile reprocessability of the spray coated NC film promises a sustainable and recyclable alternative to conventional packaging, providing a sustainable platform for packaging industries.mechnaics of non-wovens
The document defines non-woven fabrics as sheets or webs of natural or man-made fibers bonded together without weaving or knitting. It discusses the key differences in structure between non-wovens and woven/knitted fabrics. The document also describes various processes for forming non-woven webs and bonding the fibers, and how the fiber orientation distribution impacts mechanical properties depending on the testing direction. Failure mechanisms are dominated by defects from non-uniform fiber distribution or over/under bonding.
Dry laid nonwoven
This document summarizes techniques for dry laid nonwoven fabrics. It discusses fibre selection and preparation, including bale opening and blending. There are two main web formation methods: mechanical (using cards or garnets) and aerodynamic (air-laid). Webs can be layered longitudinally, crosswise, or perpendicularly. Bonds are formed through needle punching, stitch bonding, thermal bonding, chemical bonding (using latex), or hydroentanglement. Needle punching uses barbed needles to mechanically interlock fibers. Thermal bonding melts thermoplastic fibers like polypropylene to fuse the web.
Needle punching nonwovens
This document discusses nonwoven needle punching processes. It defines nonwovens and describes the three stages of nonwoven production: web formation, web bonding, and finishing treatments. It then focuses on the needle punching process, describing how barbed needles repeatedly penetrate a fibrous web to mechanically entangle the fibers. Key aspects of needle design like needle density and stroke frequency are discussed. The principles of needle punching and how it orientates fibers are also summarized. Applications of needle punched nonwovens are then listed.
Laser assisted machining on ceramics
This document summarizes research on laser assisted machining (LAM) of ceramics. It discusses how LAM allows machining of ceramics like zirconia and alumina by softening the material through localized laser heating, enabling ductile mode cutting and reducing forces. The author presents results from experiments on LAM of yttria stabilized zirconia polycrystal using a diamond bur at different laser powers, rotational speeds and feed rates. The results show grinding forces decreased with higher laser power due to enhanced brittle fracture. Surface roughness increased slightly with faster feed rates. LAM improved efficiency of machining hard ceramics for dental applications.
Spun Laid Process, Melt Blown Process, Differences between spun laid Process ...
Spun Laid Process, Melt Blown Process, Differences between spun laid Process ...MD. SAJJADUL KARIM BHUIYAN
The document provides information on the spun laid and melt blown processes for producing nonwoven fabrics from polymers. In the spun laid process, polymers are extruded through spinnerets to form fine filaments, which are then deposited randomly onto a conveyor belt and bonded. The melt blown process extrudes polymers through a die containing many small holes, and high-velocity air streams attenuate the extruded fibers to form very fine fibers that are deposited onto a collector. Key differences between the processes are that the spun laid process produces thicker fibers that are later bonded, while the melt blown process produces very fine fibers through fiber attenuation using hot air streams.Nonwoven (application, testing)
Nonwoven fabrics are produced by bonding or interlacing fibers without weaving or knitting. They have a wide range of applications including hygiene products, packaging, household goods, protective clothing, filters, and geotextiles. There are various standardized test methods to evaluate key nonwoven properties such as tear strength, stiffness, thickness, and resistance to liquids and chemicals. Proper testing ensures nonwovens meet requirements for performance, durability, and safety in their intended end uses.
4 non woven bonding systems
This document discusses different bonding systems used in non-woven fabrics including mechanical (needle punching), chemical (adhesives), thermal (heat bonding), and mechanical/warp knitting (stitch bonding). It provides photos and definitions of non-woven fabrics and describes the manufacturing process which involves forming a web and then bonding fibers together. Key bonding methods covered are needle felting, adhesive bonding, heat bonding, and stitch bonding.
Recommended
Recyclability of Spray Coated Smooth Nanocellulose films as a potential susta...
Recyclability of Spray Coated Smooth Nanocellulose films as a potential susta...Kirubanandan Shanmugam
Synthetic packaging materials are neither reprocessable, renewable nor biodegradable barrier and also difficult to recycle into useful products. While cellulose-based packaging is widely known as a renewable, reprocessable, recyclable and biodegradable material it has limited air and water vapour barrier properties. Nanocellulose (NC) has the potential to become a renewable alternative to plastic packaging barrier layers but its recyclability has not been reported. This investigation is focused on the production of spray-coated nanocellulose (NC) films and its recyclability via dispersion in water and vacuum filtration to form sheets again. Physical properties such as barrier performance and strength of NC films have been evaluated pre- and post- recycling. The recycled films retained 80% of tensile strength and significant barrier performance although the H2O vapour permeability (WVP) approximately doubled, increasing to 9.83 x 10-11 g.m-1.s-1 Pa-1, providing comparable values with for most synthetic packaging. SEM micrographs reveal no fibre agglomeration at the micro level and no damage to the fibres during recycling. The retained strength and barrier properties and facile reprocessability of the spray coated NC film promises a sustainable and recyclable alternative to conventional packaging, providing a sustainable platform for packaging industries.mechnaics of non-wovens
The document defines non-woven fabrics as sheets or webs of natural or man-made fibers bonded together without weaving or knitting. It discusses the key differences in structure between non-wovens and woven/knitted fabrics. The document also describes various processes for forming non-woven webs and bonding the fibers, and how the fiber orientation distribution impacts mechanical properties depending on the testing direction. Failure mechanisms are dominated by defects from non-uniform fiber distribution or over/under bonding.
Dry laid nonwoven
This document summarizes techniques for dry laid nonwoven fabrics. It discusses fibre selection and preparation, including bale opening and blending. There are two main web formation methods: mechanical (using cards or garnets) and aerodynamic (air-laid). Webs can be layered longitudinally, crosswise, or perpendicularly. Bonds are formed through needle punching, stitch bonding, thermal bonding, chemical bonding (using latex), or hydroentanglement. Needle punching uses barbed needles to mechanically interlock fibers. Thermal bonding melts thermoplastic fibers like polypropylene to fuse the web.
Needle punching nonwovens
This document discusses nonwoven needle punching processes. It defines nonwovens and describes the three stages of nonwoven production: web formation, web bonding, and finishing treatments. It then focuses on the needle punching process, describing how barbed needles repeatedly penetrate a fibrous web to mechanically entangle the fibers. Key aspects of needle design like needle density and stroke frequency are discussed. The principles of needle punching and how it orientates fibers are also summarized. Applications of needle punched nonwovens are then listed.
Laser assisted machining on ceramics
This document summarizes research on laser assisted machining (LAM) of ceramics. It discusses how LAM allows machining of ceramics like zirconia and alumina by softening the material through localized laser heating, enabling ductile mode cutting and reducing forces. The author presents results from experiments on LAM of yttria stabilized zirconia polycrystal using a diamond bur at different laser powers, rotational speeds and feed rates. The results show grinding forces decreased with higher laser power due to enhanced brittle fracture. Surface roughness increased slightly with faster feed rates. LAM improved efficiency of machining hard ceramics for dental applications.
Spun Laid Process, Melt Blown Process, Differences between spun laid Process ...
Spun Laid Process, Melt Blown Process, Differences between spun laid Process ...MD. SAJJADUL KARIM BHUIYAN
The document provides information on the spun laid and melt blown processes for producing nonwoven fabrics from polymers. In the spun laid process, polymers are extruded through spinnerets to form fine filaments, which are then deposited randomly onto a conveyor belt and bonded. The melt blown process extrudes polymers through a die containing many small holes, and high-velocity air streams attenuate the extruded fibers to form very fine fibers that are deposited onto a collector. Key differences between the processes are that the spun laid process produces thicker fibers that are later bonded, while the melt blown process produces very fine fibers through fiber attenuation using hot air streams.Nonwoven (application, testing)
Nonwoven fabrics are produced by bonding or interlacing fibers without weaving or knitting. They have a wide range of applications including hygiene products, packaging, household goods, protective clothing, filters, and geotextiles. There are various standardized test methods to evaluate key nonwoven properties such as tear strength, stiffness, thickness, and resistance to liquids and chemicals. Proper testing ensures nonwovens meet requirements for performance, durability, and safety in their intended end uses.
4 non woven bonding systems
This document discusses different bonding systems used in non-woven fabrics including mechanical (needle punching), chemical (adhesives), thermal (heat bonding), and mechanical/warp knitting (stitch bonding). It provides photos and definitions of non-woven fabrics and describes the manufacturing process which involves forming a web and then bonding fibers together. Key bonding methods covered are needle felting, adhesive bonding, heat bonding, and stitch bonding.
IRJET- Pile Height and Terry Fabric - A Study
The document studies the effect of pile height on various properties of terry fabrics, finding that increasing pile height significantly increases fabric thickness, GSM, tensile strength, and moisture absorption, while decreasing air permeability and water absorbency time. Three terry fabrics were produced with pile heights of 3.5 mm, 4.2 mm, and 4.6 mm using cotton yarn, and their properties were analyzed and compared. In general, properties correlated positively with increased pile height due to the greater amount of yarn and loop surface area available.
Abhi rana)4. dry laid non woven fabrics
This document discusses dry laid non-woven fabrics. It describes the four phases of non-woven technology: fiber selection, fiber preparation, web formation and layering, and bonding and stabilization of the web. It then provides details on different fiber properties and various web formation methods like carding, garnetting, air laying and centrifugal dynamic random carding. Finally, it covers bonding methods for non-wovens like needle punching, stitch bonding, thermal bonding and hydroentanglement.
Nonwoven web formation rajesh
This document discusses nonwoven web formation. It describes how fibers are opened, individualized, and formed into a continuous web. The key stages of nonwoven production are web formation, bonding the web, and finishing treatments. Common web formation methods include carding, air laying, and wet laying. Carding individualizes fibers and forms them into a parallel web. Cross-lapping and vertical lapping are used to build thickness. Web formation determines the properties of the final nonwoven fabric.
Abhi rana)1. classification of non wovens
This document discusses different types of non-woven fabrics classified according to their production method, raw material technology, end use of raw material, and properties. It describes spun lace, thermal bonded, pulp air-laid, wet, spun bonded, melt-blown, needle punched, and stitch-bonded non-woven fabrication processes. Non-woven fabrics are further categorized as wet bonded, dry bonded, or spun bonded according to their production method. The document also covers classifications by raw material type and end use, as well as properties including flame retardant, water repellent, and water absorbent qualities.
Shrinkage of ttqc ii
1) Shrinkage is a dimensional change in fabrics where they become smaller than their original size, usually due to laundry. It is one of the main disadvantages of fabrics.
2) There are several types of shrinkage testing procedures, including relaxation shrinkage, felting shrinkage, compressive shrinkage, and residual shrinkage.
3) Factors that influence shrinkage include yarn swelling, twist factor, stitch length, GSM, elasticity of yarn, stability of fibers and yarns, construction, type of weave or knit, and tension during sewing of garments. Proper control methods like correct construction, eliminating excess tensions, and spreading with softener can help reduce shrink
Mechanics of Composite Materials
This document discusses opportunities and challenges for textile reinforced composites. It describes how textiles can be formed using various processes like weaving, knitting, braiding, and direct forming to create structures with multiple fiber orientations. Textiles are considered to have cost advantages over tape layup methods. However, shaping textiles to create tapered or complex geometries can introduce variations in fiber volume fraction, weave angle, yarn distribution, and mechanical properties across the structure. Careful design is required to minimize these variations.
MSE-4105-Chapter-2-Manufacturing of Composites.pdf
This document discusses various processing techniques and manufacturing processes for fiber-reinforced polymer matrix composites. It describes structural, semi-structural, and non-structural processing techniques based on fiber alignment. Various manufacturing processes are then discussed, including hand lay-up, pultrusion, resin transfer molding, filament winding, compression molding, injection molding, blow molding, and infiltration. Key factors affecting the selection of manufacturing processes are identified as production rate, cost, part requirements, geometry, and material.
wet laid web preparation
The document discusses wet-laid nonwoven fabric manufacturing using a modified papermaking process. Key points include:
- Wet-laid nonwovens are made by dispersing fibers in water and draining the mixture on a wire to form a uniform sheet, which is then bonded and dried.
- The process involves mixing fibers with water to form a suspension, pumping the suspension through a headbox onto a moving wire, draining water through the wire to form a web, and then drying and bonding the web.
- Common raw materials include wood pulp for its low cost and properties, as well as some natural and synthetic fibers that can meet needed properties. Factors like fiber length and compatibility with water must
Http --www raypcb-com-rigid-pcb-capacity
This document provides information on the rigid PCB manufacturing capabilities of Rayming Technology, including layer counts, panel sizes, thickness ranges, design rule minimums, and quality assurance testing specifications for prototype and mass production boards. Contact information is provided at the bottom for sales inquiries.
Abhi rana)5. wet laid nonwovens
This document provides information on wet laid nonwoven technology. It discusses the key steps in the wet laid nonwoven process which includes mixing fibers and water to form a slurry, depositing the slurry onto a wire screen to drain water and form a fiber web, bonding and drying the web. It also describes the specialized papermaking machines used, including the fourdrinier machine. Different raw materials used and applications of wet laid nonwovens are mentioned. Defects in wet laid webs and continuous filament processes like spunlaid and meltblown are also summarized.
Spirality & Shrinkage
This project report summarizes work done on analyzing and minimizing spirality and shrinkage problems in knitted fabrics. It discusses raw materials used, yarn types and counts, subcontractors, and costs. It also provides an overview of the evolution of Bangladesh's knitting industry and its social and economic impacts. Key points are that spirality is caused by yarn twist and machine settings, while shrinkage is due to yarn swelling; both can be reduced through washing, drying, and fabric construction methods. The knitting industry is a major employer and exporter for Bangladesh.
Fabric Quality Parameters Tested in Quality Control Lab - Textile Testing & Q...
Fabric Quality Parameters Tested in Quality Control Lab - Textile Testing & Quality Control
Department:Textile Engineering & Management
BUFT
PRESENTED BY : Mazedin Reza
Pultrusion process
Pultrusion is a continuous process for manufacture of composite materials with constant cross-section.
It is more widely used in industries where there is a continuous demand of the product
Non woven fabrics - Non woven technology
Non-woven fabrics are made from staple fibers or filaments that are bonded together through mechanical, thermal, chemical, or solvent treatments rather than weaving or knitting. The document discusses the history and definitions of non-woven fabrics. It then summarizes the key stages of non-woven manufacturing including web formation through processes like carding, air laying, and wet laying. It also discusses bonding methods like thermal, chemical, and mechanical and provides examples. The applications and characteristics of non-woven fabrics are then outlined.
Effect of finishing on Knit Fabrics
This document discusses the effect of finishing processes on knit fabrics. It describes how finishing improves physical properties like feel, strength and shrinkage. The techniques of finishing depend on factors like the fabric composition and its intended end use. Common finishing treatments aim to impart properties like softness, luster and dimensional stability. The document then examines specific finishing stages like hydroextraction, drying, slitting, stenting and compacting. Graphs show how properties like GSM and shrinkage are affected differently for various fabric types as they progress through finishing. The discussion analyzes the results and references additional sources for information on textile finishing.
Fabric Shrinkage
This document discusses different types of shrinkage that can occur in fabrics, including relaxation shrinkage, felting shrinkage, compressive shrinkage, residual shrinkage, processing shrinkage, drying shrinkage, and elastic shrinkage. It explains the causes of each type of shrinkage and factors that influence the amount of shrinkage, such as fiber type, yarn construction, fabric weight, stitch length, and finishing processes. Methods for controlling and reducing shrinkage are also outlined.
公司及产品信息概述
We can produce various specifications of stainless steel wire mesh according to
customers' requirements, such as wire diameter, mesh size, mesh shape, mesh thickness, etc. The
maximum width is 3200mm. We guarantee the quality and on-time delivery.
Needle punch nonwoven applications
Needle punch is the second-largest market segment in terms of capacity after the spunbond process segment. It is a continuously growing market with new opportunities and growing demands in its core applications like automotive, geotextiles, filtration, and home products.
For more information log on to www.ategroup.com.
Singeing Machine for knits fabrics.pdf
This document introduces the XSM Series Singeing Machine, which is used to singe knitted fabrics. It has a compact design for easy operation and avoids creasing through motor-driven rollers and PLC control. The machine uses an S-shape movement and open width roller to fully expose and uncurl fabrics for effective singeing. It has advantages like improved surface appearance and strength for fabrics as well as reduced dyeing time and costs. The technical specifications provide the machine widths, heating options, gas consumption, speeds, singeing methods, cooling system, and fire safety features.
Non woven Fabrics
This document provides an overview of non-woven fabrics. It defines non-woven fabrics as sheet or web structures bonded together by entangling fibers or filaments mechanically, thermally, chemically or through solvent treatment. The document discusses the history of non-woven fabrics and mentions some early precursors. It also outlines different types of non-woven fabrics based on materials used and manufacturing processes. Common applications of non-woven fabrics in various industries are also summarized.
Techtex
Kalpesh Synthetics Pvt. Ltd is an Indian manufacturer of technical and industrial textiles established in 1987. It produces a variety of woven fabrics from high tenacity yarns like polyester, aramid, nylon, polypropylene, and cotton blends. The company has a production capacity of 15,000 linear meters per day across looms from Sulzer, Vamatex, and Dornier. Key products include woven geotextiles, industrial filter fabrics, industrial canvases, and liner fabrics for tire industries. Testing, research and development, and sample development facilities are also available.
IRJET- Study of Reed on High Speed Weaving Machines
This document discusses reeds used in high-speed weaving machines and how to increase the life of reeds. It begins by explaining what a reed is and how it is constructed. It then discusses the problem of groove formation in reeds, where the dent wires are cut, which decreases reed life. Groove formation commonly occurs within 500 hours and is caused by high tension and abrasion on selvedge ends from the contraction between the reed and woven cloth. Several factors can influence groove formation, including fabric construction, yarn type, loom settings, sizing recipe, and reed construction. The document provides solutions to prevent groove formation, such as selecting the proper reed specifications, temple,
More Related Content
What's hot
IRJET- Pile Height and Terry Fabric - A Study
The document studies the effect of pile height on various properties of terry fabrics, finding that increasing pile height significantly increases fabric thickness, GSM, tensile strength, and moisture absorption, while decreasing air permeability and water absorbency time. Three terry fabrics were produced with pile heights of 3.5 mm, 4.2 mm, and 4.6 mm using cotton yarn, and their properties were analyzed and compared. In general, properties correlated positively with increased pile height due to the greater amount of yarn and loop surface area available.
Abhi rana)4. dry laid non woven fabrics
This document discusses dry laid non-woven fabrics. It describes the four phases of non-woven technology: fiber selection, fiber preparation, web formation and layering, and bonding and stabilization of the web. It then provides details on different fiber properties and various web formation methods like carding, garnetting, air laying and centrifugal dynamic random carding. Finally, it covers bonding methods for non-wovens like needle punching, stitch bonding, thermal bonding and hydroentanglement.
Nonwoven web formation rajesh
This document discusses nonwoven web formation. It describes how fibers are opened, individualized, and formed into a continuous web. The key stages of nonwoven production are web formation, bonding the web, and finishing treatments. Common web formation methods include carding, air laying, and wet laying. Carding individualizes fibers and forms them into a parallel web. Cross-lapping and vertical lapping are used to build thickness. Web formation determines the properties of the final nonwoven fabric.
Abhi rana)1. classification of non wovens
This document discusses different types of non-woven fabrics classified according to their production method, raw material technology, end use of raw material, and properties. It describes spun lace, thermal bonded, pulp air-laid, wet, spun bonded, melt-blown, needle punched, and stitch-bonded non-woven fabrication processes. Non-woven fabrics are further categorized as wet bonded, dry bonded, or spun bonded according to their production method. The document also covers classifications by raw material type and end use, as well as properties including flame retardant, water repellent, and water absorbent qualities.
Shrinkage of ttqc ii
1) Shrinkage is a dimensional change in fabrics where they become smaller than their original size, usually due to laundry. It is one of the main disadvantages of fabrics.
2) There are several types of shrinkage testing procedures, including relaxation shrinkage, felting shrinkage, compressive shrinkage, and residual shrinkage.
3) Factors that influence shrinkage include yarn swelling, twist factor, stitch length, GSM, elasticity of yarn, stability of fibers and yarns, construction, type of weave or knit, and tension during sewing of garments. Proper control methods like correct construction, eliminating excess tensions, and spreading with softener can help reduce shrink
Mechanics of Composite Materials
This document discusses opportunities and challenges for textile reinforced composites. It describes how textiles can be formed using various processes like weaving, knitting, braiding, and direct forming to create structures with multiple fiber orientations. Textiles are considered to have cost advantages over tape layup methods. However, shaping textiles to create tapered or complex geometries can introduce variations in fiber volume fraction, weave angle, yarn distribution, and mechanical properties across the structure. Careful design is required to minimize these variations.
MSE-4105-Chapter-2-Manufacturing of Composites.pdf
This document discusses various processing techniques and manufacturing processes for fiber-reinforced polymer matrix composites. It describes structural, semi-structural, and non-structural processing techniques based on fiber alignment. Various manufacturing processes are then discussed, including hand lay-up, pultrusion, resin transfer molding, filament winding, compression molding, injection molding, blow molding, and infiltration. Key factors affecting the selection of manufacturing processes are identified as production rate, cost, part requirements, geometry, and material.
wet laid web preparation
The document discusses wet-laid nonwoven fabric manufacturing using a modified papermaking process. Key points include:
- Wet-laid nonwovens are made by dispersing fibers in water and draining the mixture on a wire to form a uniform sheet, which is then bonded and dried.
- The process involves mixing fibers with water to form a suspension, pumping the suspension through a headbox onto a moving wire, draining water through the wire to form a web, and then drying and bonding the web.
- Common raw materials include wood pulp for its low cost and properties, as well as some natural and synthetic fibers that can meet needed properties. Factors like fiber length and compatibility with water must
Http --www raypcb-com-rigid-pcb-capacity
This document provides information on the rigid PCB manufacturing capabilities of Rayming Technology, including layer counts, panel sizes, thickness ranges, design rule minimums, and quality assurance testing specifications for prototype and mass production boards. Contact information is provided at the bottom for sales inquiries.
Abhi rana)5. wet laid nonwovens
This document provides information on wet laid nonwoven technology. It discusses the key steps in the wet laid nonwoven process which includes mixing fibers and water to form a slurry, depositing the slurry onto a wire screen to drain water and form a fiber web, bonding and drying the web. It also describes the specialized papermaking machines used, including the fourdrinier machine. Different raw materials used and applications of wet laid nonwovens are mentioned. Defects in wet laid webs and continuous filament processes like spunlaid and meltblown are also summarized.
Spirality & Shrinkage
This project report summarizes work done on analyzing and minimizing spirality and shrinkage problems in knitted fabrics. It discusses raw materials used, yarn types and counts, subcontractors, and costs. It also provides an overview of the evolution of Bangladesh's knitting industry and its social and economic impacts. Key points are that spirality is caused by yarn twist and machine settings, while shrinkage is due to yarn swelling; both can be reduced through washing, drying, and fabric construction methods. The knitting industry is a major employer and exporter for Bangladesh.
Fabric Quality Parameters Tested in Quality Control Lab - Textile Testing & Q...
Fabric Quality Parameters Tested in Quality Control Lab - Textile Testing & Quality Control
Department:Textile Engineering & Management
BUFT
PRESENTED BY : Mazedin Reza
Pultrusion process
Pultrusion is a continuous process for manufacture of composite materials with constant cross-section.
It is more widely used in industries where there is a continuous demand of the product
Non woven fabrics - Non woven technology
Non-woven fabrics are made from staple fibers or filaments that are bonded together through mechanical, thermal, chemical, or solvent treatments rather than weaving or knitting. The document discusses the history and definitions of non-woven fabrics. It then summarizes the key stages of non-woven manufacturing including web formation through processes like carding, air laying, and wet laying. It also discusses bonding methods like thermal, chemical, and mechanical and provides examples. The applications and characteristics of non-woven fabrics are then outlined.
Effect of finishing on Knit Fabrics
This document discusses the effect of finishing processes on knit fabrics. It describes how finishing improves physical properties like feel, strength and shrinkage. The techniques of finishing depend on factors like the fabric composition and its intended end use. Common finishing treatments aim to impart properties like softness, luster and dimensional stability. The document then examines specific finishing stages like hydroextraction, drying, slitting, stenting and compacting. Graphs show how properties like GSM and shrinkage are affected differently for various fabric types as they progress through finishing. The discussion analyzes the results and references additional sources for information on textile finishing.
Fabric Shrinkage
This document discusses different types of shrinkage that can occur in fabrics, including relaxation shrinkage, felting shrinkage, compressive shrinkage, residual shrinkage, processing shrinkage, drying shrinkage, and elastic shrinkage. It explains the causes of each type of shrinkage and factors that influence the amount of shrinkage, such as fiber type, yarn construction, fabric weight, stitch length, and finishing processes. Methods for controlling and reducing shrinkage are also outlined.
What's hot (16)
MSE-4105-Chapter-2-Manufacturing of Composites.pdf
MSE-4105-Chapter-2-Manufacturing of Composites.pdf
Fabric Quality Parameters Tested in Quality Control Lab - Textile Testing & Q...
Fabric Quality Parameters Tested in Quality Control Lab - Textile Testing & Q...
Similar to 1.5 layer forming farbics by HENAN BEYNOST TEXTILE TECHNOLOGY CO., LTD.
公司及产品信息概述
We can produce various specifications of stainless steel wire mesh according to
customers' requirements, such as wire diameter, mesh size, mesh shape, mesh thickness, etc. The
maximum width is 3200mm. We guarantee the quality and on-time delivery.
Needle punch nonwoven applications
Needle punch is the second-largest market segment in terms of capacity after the spunbond process segment. It is a continuously growing market with new opportunities and growing demands in its core applications like automotive, geotextiles, filtration, and home products.
For more information log on to www.ategroup.com.
Singeing Machine for knits fabrics.pdf
This document introduces the XSM Series Singeing Machine, which is used to singe knitted fabrics. It has a compact design for easy operation and avoids creasing through motor-driven rollers and PLC control. The machine uses an S-shape movement and open width roller to fully expose and uncurl fabrics for effective singeing. It has advantages like improved surface appearance and strength for fabrics as well as reduced dyeing time and costs. The technical specifications provide the machine widths, heating options, gas consumption, speeds, singeing methods, cooling system, and fire safety features.
Non woven Fabrics
This document provides an overview of non-woven fabrics. It defines non-woven fabrics as sheet or web structures bonded together by entangling fibers or filaments mechanically, thermally, chemically or through solvent treatment. The document discusses the history of non-woven fabrics and mentions some early precursors. It also outlines different types of non-woven fabrics based on materials used and manufacturing processes. Common applications of non-woven fabrics in various industries are also summarized.
Techtex
Kalpesh Synthetics Pvt. Ltd is an Indian manufacturer of technical and industrial textiles established in 1987. It produces a variety of woven fabrics from high tenacity yarns like polyester, aramid, nylon, polypropylene, and cotton blends. The company has a production capacity of 15,000 linear meters per day across looms from Sulzer, Vamatex, and Dornier. Key products include woven geotextiles, industrial filter fabrics, industrial canvases, and liner fabrics for tire industries. Testing, research and development, and sample development facilities are also available.
IRJET- Study of Reed on High Speed Weaving Machines
This document discusses reeds used in high-speed weaving machines and how to increase the life of reeds. It begins by explaining what a reed is and how it is constructed. It then discusses the problem of groove formation in reeds, where the dent wires are cut, which decreases reed life. Groove formation commonly occurs within 500 hours and is caused by high tension and abrasion on selvedge ends from the contraction between the reed and woven cloth. Several factors can influence groove formation, including fabric construction, yarn type, loom settings, sizing recipe, and reed construction. The document provides solutions to prevent groove formation, such as selecting the proper reed specifications, temple,
Nonwoven fabric
Here i discussed about Nonwoven fabric. Also discussed about it's characteristics, classification, manufacturing process, application etc.
Jigger dyeing machine
This document provides information about jigger dyeing machines. It discusses that jigger dyeing machines apply tension to woven fabrics as they pass through a dye bath. The document outlines the main parts of jigger dyeing machines, including guide rollers, take up rollers, let off rollers, and dye baths. It also discusses technical details like fabric tension and speed. The document summarizes advantages of modern jigger dyeing machines like improved tension and speed control. It notes that jiggers are suitable for dyeing woven fabrics up to boiling temperatures without creasing.
VICTOR Company Presentation
Changzhou Victor Envirotech Co. Ltd. is a filtration textile manufacturer established in 1997 with over 150 employees including 35 technicians. The company has advanced equipment for needle felting, weaving, heat setting, and laser cutting. They produce various filter cloth types from filament, spun fiber, monofilament, and multifilament and can customize products. Jason Qi is the sales manager providing contact information to discuss filtration needs.
Filtration (1)
This document discusses filtration theory, including definitions of filtration, objectives of filtration, types of filtration collections and fibers used. It describes filtration efficiencies of different collector types and how yarn characteristics and weaves influence efficiency. The document outlines manufacturing methods, classifications of filtration, design considerations and testing of filters. It concludes that the optimal filter fabric depends on the specific use and conditions.
Sewing threads1
The document discusses sewing threads and their manufacturing process. It defines sewing threads and their various uses in garments, upholstery, and other fabrics. It then describes the different types of fibers used - including cotton, polyester, rayon, nylon and metallics - and their characteristics. Next, it discusses factors that influence the cost of sewing threads. It concludes by outlining the functions of various machines used in the sewing thread manufacturing process and different types of winding systems.
Recent development in needle punching nonwoven manufacturing
This document provides details on the production and testing of nonwoven fabrics made from reclaimed fibers using needle punching. It describes the methodology used, including refiberizing textile waste into fibers, forming a web through carding or air laying, needle punching the web to bond the fibers, and optionally calendering the fabric. It discusses how machine parameters like needle density and punching speed influence fabric properties. The properties tested include thickness, strength, bonding strength between layers, and air permeability. The goal is to compare nonwovens made from reclaimed fibers to ordinary nonwovens and evaluate their potential use in filtration applications.
Nonwoven technologies: A critical analysys by Vignesh Dhanabalan
This document provides an overview of nonwoven technologies. It discusses the various raw materials and web forming techniques used, including drylaid, wetlaid, spunlaid, and meltblown. It also describes key bonding techniques like needlepunching, hydroentanglement, stitchbonding, and chemical/adhesive bonding. The document aims to elaborate on the manufacturing process of nonwovens and emphasize fiber usage, web laying technologies, converting webs to fabrics, and key applications in various end markets.
Spinning machinery
This document provides an overview of the layout and machinery used in a spinning plant. It describes the key processes including blow room, carding, draw frame, combing, speed frame, ring frame, winding, and conditioning. It lists common machinery manufacturers and provides links to related textile technology Facebook pages and the author's blog.
DEVELOPMENT OF SUSTAINABLE ECO FRIENDLY SANITARY NAPKINS USING NATURAL FIBRES...
The document discusses the development of sustainable and eco-friendly sanitary napkins using natural fibers like banana fiber, cotton, and linen. It describes the extraction processes for these fibers, including mechanical stripping of banana fiber and chemical scouring/purifying of cotton. The properties of each fiber are compared, with banana fiber having good strength but low elasticity. The fibers will be used to make napkins with banana fiber and linen for absorption layers and cotton for the top sheet.
KARL MAYER SIM.PLY - High-performance Spreading and Impregnation Line for Con...
KARL MAYER SIM.PLY - High-performance Spreading and Impregnation Line for Con...A.T.E. Private Limited
Introducing SIM.PLY, a technology from our principal (KARL MAYER) that offers a comprehensive and high-quality solution for manufacturing Continuous Fibre Reinforced Thermoplastic (CFRT) tapes. CFRT tapes have numerous applications such as automotive, construction, consumer products, etc. Connect with us to know more. Take a look at the presentation for more detailed information about the product.Application of 3D fabric in technical textile
1) Spacer fabrics are three dimensional knitted fabrics consisting of two separate knitted structures joined by spacer yarns.
2) They have properties like breathability, cushioning, insulation and good bending performance.
3) Spacer fabrics have applications in automotive, home textiles, sports/clothing, and medicine due to their physical properties and ability to regulate air, heat, and moisture transfer.
2.0 UNIclean Machine in Blow room line.pdf
1. The document discusses the UNIclean machine in the blow room process for cleaning cotton fibers.
2. It describes the working principle of the UNIclean machine, which uses double hooks to pass the material over a cleaning grid five times to remove dirt and debris.
3. The objectives of the UNIclean machine are to remove particles, dust, and trash from the fibers to individualize and straighten them for subsequent spinning.
Picanol News October 2010
The document provides information about Picanol, a weaving machine manufacturer. It discusses Picanol's latest developments including airjet weaving without a filling catch cord ("Cordless") and their new TERRYplus 800 machine for terry weaving. It also highlights two Picanol customers, Berto Industria Tessile in Italy and Wagdy Moamen Weaving Mill in Egypt, and their positive experiences with Picanol machines.
Spinning technology
This document discusses the working principles and technical specifications of several machines used in cotton processing:
1. The BDT opens compressed cotton bales by penetrating them with opening rollers fitted with toothed discs, plucking tufts of fiber and converting them to smaller sizes for further processing.
2. The CL-C3 uses a series of rotating beaters to open cotton tufts to the smallest size and clean them by removing trash and dust using grid bars.
3. The SP-FP screens cotton fibers using 3 CCD cameras and detects contaminants, then uses compressed air nozzles and suction to remove the contaminated fibers from the processing line.
Similar to 1.5 layer forming farbics by HENAN BEYNOST TEXTILE TECHNOLOGY CO., LTD. (20)
IRJET- Study of Reed on High Speed Weaving Machines
IRJET- Study of Reed on High Speed Weaving Machines
Recent development in needle punching nonwoven manufacturing
Recent development in needle punching nonwoven manufacturing
Nonwoven technologies: A critical analysys by Vignesh Dhanabalan
Nonwoven technologies: A critical analysys by Vignesh Dhanabalan
DEVELOPMENT OF SUSTAINABLE ECO FRIENDLY SANITARY NAPKINS USING NATURAL FIBRES...
DEVELOPMENT OF SUSTAINABLE ECO FRIENDLY SANITARY NAPKINS USING NATURAL FIBRES...
KARL MAYER SIM.PLY - High-performance Spreading and Impregnation Line for Con...
KARL MAYER SIM.PLY - High-performance Spreading and Impregnation Line for Con...
Recently uploaded
Let's Integrate MuleSoft RPA, COMPOSER, APM with AWS IDP along with Slack
Discover the seamless integration of RPA (Robotic Process Automation), COMPOSER, and APM with AWS IDP enhanced with Slack notifications. Explore how these technologies converge to streamline workflows, optimize performance, and ensure secure access, all while leveraging the power of AWS IDP and real-time communication via Slack notifications.
Climate Impact of Software Testing at Nordic Testing Days
My slides at Nordic Testing Days 6.6.2024
Climate impact / sustainability of software testing discussed on the talk. ICT and testing must carry their part of global responsibility to help with the climat warming. We can minimize the carbon footprint but we can also have a carbon handprint, a positive impact on the climate. Quality characteristics can be added with sustainability, and then measured continuously. Test environments can be used less, and in smaller scale and on demand. Test techniques can be used in optimizing or minimizing number of tests. Test automation can be used to speed up testing.
Cosa hanno in comune un mattoncino Lego e la backdoor XZ?
ABSTRACT: A prima vista, un mattoncino Lego e la backdoor XZ potrebbero avere in comune il fatto di essere entrambi blocchi di costruzione, o dipendenze di progetti creativi e software. La realtà è che un mattoncino Lego e il caso della backdoor XZ hanno molto di più di tutto ciò in comune.
Partecipate alla presentazione per immergervi in una storia di interoperabilità, standard e formati aperti, per poi discutere del ruolo importante che i contributori hanno in una comunità open source sostenibile.
BIO: Sostenitrice del software libero e dei formati standard e aperti. È stata un membro attivo dei progetti Fedora e openSUSE e ha co-fondato l'Associazione LibreItalia dove è stata coinvolta in diversi eventi, migrazioni e formazione relativi a LibreOffice. In precedenza ha lavorato a migrazioni e corsi di formazione su LibreOffice per diverse amministrazioni pubbliche e privati. Da gennaio 2020 lavora in SUSE come Software Release Engineer per Uyuni e SUSE Manager e quando non segue la sua passione per i computer e per Geeko coltiva la sua curiosità per l'astronomia (da cui deriva il suo nickname deneb_alpha).
Building RAG with self-deployed Milvus vector database and Snowpark Container...
This talk will give hands-on advice on building RAG applications with an open-source Milvus database deployed as a docker container. We will also introduce the integration of Milvus with Snowpark Container Services.
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...
The choice of an operating system plays a pivotal role in shaping our computing experience. For decades, Microsoft's Windows has dominated the market, offering a familiar and widely adopted platform for personal and professional use. However, as technological advancements continue to push the boundaries of innovation, alternative operating systems have emerged, challenging the status quo and offering users a fresh perspective on computing.
One such alternative that has garnered significant attention and acclaim is Nitrux Linux 3.5.0, a sleek, powerful, and user-friendly Linux distribution that promises to redefine the way we interact with our devices. With its focus on performance, security, and customization, Nitrux Linux presents a compelling case for those seeking to break free from the constraints of proprietary software and embrace the freedom and flexibility of open-source computing.
Goodbye Windows 11: Make Way for Nitrux Linux 3.5.0!
As the digital landscape continually evolves, operating systems play a critical role in shaping user experiences and productivity. The launch of Nitrux Linux 3.5.0 marks a significant milestone, offering a robust alternative to traditional systems such as Windows 11. This article delves into the essence of Nitrux Linux 3.5.0, exploring its unique features, advantages, and how it stands as a compelling choice for both casual users and tech enthusiasts.
Generative AI Deep Dive: Advancing from Proof of Concept to Production
Join Maher Hanafi, VP of Engineering at Betterworks, in this new session where he'll share a practical framework to transform Gen AI prototypes into impactful products! He'll delve into the complexities of data collection and management, model selection and optimization, and ensuring security, scalability, and responsible use.
20240607 QFM018 Elixir Reading List May 2024
Everything I found interesting about the Elixir programming ecosystem in May 2024
Full-RAG: A modern architecture for hyper-personalization
Mike Del Balso, CEO & Co-Founder at Tecton, presents "Full RAG," a novel approach to AI recommendation systems, aiming to push beyond the limitations of traditional models through a deep integration of contextual insights and real-time data, leveraging the Retrieval-Augmented Generation architecture. This talk will outline Full RAG's potential to significantly enhance personalization, address engineering challenges such as data management and model training, and introduce data enrichment with reranking as a key solution. Attendees will gain crucial insights into the importance of hyperpersonalization in AI, the capabilities of Full RAG for advanced personalization, and strategies for managing complex data integrations for deploying cutting-edge AI solutions.
Introducing Milvus Lite: Easy-to-Install, Easy-to-Use vector database for you...
Join us to introduce Milvus Lite, a vector database that can run on notebooks and laptops, share the same API with Milvus, and integrate with every popular GenAI framework. This webinar is perfect for developers seeking easy-to-use, well-integrated vector databases for their GenAI apps.
How to Get CNIC Information System with Paksim Ga.pptx
Pakdata Cf is a groundbreaking system designed to streamline and facilitate access to CNIC information. This innovative platform leverages advanced technology to provide users with efficient and secure access to their CNIC details.
Alt. GDG Cloud Southlake #33: Boule & Rebala: Effective AppSec in SDLC using ...
Effective Application Security in Software Delivery lifecycle using Deployment Firewall and DBOM
The modern software delivery process (or the CI/CD process) includes many tools, distributed teams, open-source code, and cloud platforms. Constant focus on speed to release software to market, along with the traditional slow and manual security checks has caused gaps in continuous security as an important piece in the software supply chain. Today organizations feel more susceptible to external and internal cyber threats due to the vast attack surface in their applications supply chain and the lack of end-to-end governance and risk management.
The software team must secure its software delivery process to avoid vulnerability and security breaches. This needs to be achieved with existing tool chains and without extensive rework of the delivery processes. This talk will present strategies and techniques for providing visibility into the true risk of the existing vulnerabilities, preventing the introduction of security issues in the software, resolving vulnerabilities in production environments quickly, and capturing the deployment bill of materials (DBOM).
Speakers:
Bob Boule
Robert Boule is a technology enthusiast with PASSION for technology and making things work along with a knack for helping others understand how things work. He comes with around 20 years of solution engineering experience in application security, software continuous delivery, and SaaS platforms. He is known for his dynamic presentations in CI/CD and application security integrated in software delivery lifecycle.
Gopinath Rebala
Gopinath Rebala is the CTO of OpsMx, where he has overall responsibility for the machine learning and data processing architectures for Secure Software Delivery. Gopi also has a strong connection with our customers, leading design and architecture for strategic implementations. Gopi is a frequent speaker and well-known leader in continuous delivery and integrating security into software delivery.
Removing Uninteresting Bytes in Software Fuzzing
Imagine a world where software fuzzing, the process of mutating bytes in test seeds to uncover hidden and erroneous program behaviors, becomes faster and more effective. A lot depends on the initial seeds, which can significantly dictate the trajectory of a fuzzing campaign, particularly in terms of how long it takes to uncover interesting behaviour in your code. We introduce DIAR, a technique designed to speedup fuzzing campaigns by pinpointing and eliminating those uninteresting bytes in the seeds. Picture this: instead of wasting valuable resources on meaningless mutations in large, bloated seeds, DIAR removes the unnecessary bytes, streamlining the entire process.
In this work, we equipped AFL, a popular fuzzer, with DIAR and examined two critical Linux libraries -- Libxml's xmllint, a tool for parsing xml documents, and Binutil's readelf, an essential debugging and security analysis command-line tool used to display detailed information about ELF (Executable and Linkable Format). Our preliminary results show that AFL+DIAR does not only discover new paths more quickly but also achieves higher coverage overall. This work thus showcases how starting with lean and optimized seeds can lead to faster, more comprehensive fuzzing campaigns -- and DIAR helps you find such seeds.
- These are slides of the talk given at IEEE International Conference on Software Testing Verification and Validation Workshop, ICSTW 2022.
GraphSummit Singapore | Graphing Success: Revolutionising Organisational Stru...
Sudheer Mechineni, Head of Application Frameworks, Standard Chartered Bank
Discover how Standard Chartered Bank harnessed the power of Neo4j to transform complex data access challenges into a dynamic, scalable graph database solution. This keynote will cover their journey from initial adoption to deploying a fully automated, enterprise-grade causal cluster, highlighting key strategies for modelling organisational changes and ensuring robust disaster recovery. Learn how these innovations have not only enhanced Standard Chartered Bank’s data infrastructure but also positioned them as pioneers in the banking sector’s adoption of graph technology.
Video Streaming: Then, Now, and in the Future
In his public lecture, Christian Timmerer provides insights into the fascinating history of video streaming, starting from its humble beginnings before YouTube to the groundbreaking technologies that now dominate platforms like Netflix and ORF ON. Timmerer also presents provocative contributions of his own that have significantly influenced the industry. He concludes by looking at future challenges and invites the audience to join in a discussion.
みなさんこんにちはこれ何文字まで入るの？40文字以下不可とか本当に意味わからないけどこれ限界文字数書いてないからマジでやばい文字数いけるんじゃないの？えこ...
ここ3000字までしか入らないけどタイトルの方がたくさん文字入ると思います。
Recently uploaded (20)
Let's Integrate MuleSoft RPA, COMPOSER, APM with AWS IDP along with Slack
Let's Integrate MuleSoft RPA, COMPOSER, APM with AWS IDP along with Slack
Climate Impact of Software Testing at Nordic Testing Days
Climate Impact of Software Testing at Nordic Testing Days
Cosa hanno in comune un mattoncino Lego e la backdoor XZ?
Cosa hanno in comune un mattoncino Lego e la backdoor XZ?
Building RAG with self-deployed Milvus vector database and Snowpark Container...
Building RAG with self-deployed Milvus vector database and Snowpark Container...
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...
Goodbye Windows 11: Make Way for Nitrux Linux 3.5.0!
Goodbye Windows 11: Make Way for Nitrux Linux 3.5.0!
Generative AI Deep Dive: Advancing from Proof of Concept to Production
Generative AI Deep Dive: Advancing from Proof of Concept to Production
Full-RAG: A modern architecture for hyper-personalization
Full-RAG: A modern architecture for hyper-personalization
Introducing Milvus Lite: Easy-to-Install, Easy-to-Use vector database for you...
Introducing Milvus Lite: Easy-to-Install, Easy-to-Use vector database for you...
How to Get CNIC Information System with Paksim Ga.pptx
How to Get CNIC Information System with Paksim Ga.pptx
Alt. GDG Cloud Southlake #33: Boule & Rebala: Effective AppSec in SDLC using ...
Alt. GDG Cloud Southlake #33: Boule & Rebala: Effective AppSec in SDLC using ...
GraphSummit Singapore | Graphing Success: Revolutionising Organisational Stru...
GraphSummit Singapore | Graphing Success: Revolutionising Organisational Stru...
みなさんこんにちはこれ何文字まで入るの？40文字以下不可とか本当に意味わからないけどこれ限界文字数書いてないからマジでやばい文字数いけるんじゃないの？えこ...
みなさんこんにちはこれ何文字まで入るの？40文字以下不可とか本当に意味わからないけどこれ限界文字数書いてないからマジでやばい文字数いけるんじゃないの？えこ...
1.5 layer forming farbics by HENAN BEYNOST TEXTILE TECHNOLOGY CO., LTD.
- 1. HENAN BEYNOST TEXTILE TECHNOLOGY CO. LTD Address: Henan Pilot Free Trade Zone (Zhengdong), China Tel: 0086 18837189119 Email: vincent@benost.com. Web: www.benost.com Technical Data Sheet Forming Fabrics: The 10 shed 1.5 layer forming fabric has stronger dewatering performance and secondary Fiber Recycling and Straw Pulping Application for papermaking long paper machine or long wire paper machine with a weight of between 50-220g to reduce paper machine wear. Benefits： 1. Stronger dewatering performance, long life. 2. Excellent formation and excellent fiber support. 3. No fabric marking and easy to clean. 4. Very good stable and wear resistance. Technical Properties: Product Name : 1.5 layer polyester Forming fabrics Material : 100% Polyester WarpDiameter : 0.18 mm Weft Diameter : 0.45, 0.2 mm Warp Density : 24 Weft Density : 30 Strength (N/cm) Surface : 1000N/cm CFM : 530