1 b. Threaded fasteners and powers screws examples
•Download as PPT, PDF•
0 likes•85 views
Two machine parts are fastened together with a 24mm tap bolt. The document provides examples of calculating stresses in fasteners like bolts from applied loads. One example calculates the stress set up in a bolt from initial tightening without any separating load. Another example calculates the minimum nominal diameter needed for an eye bolt to lift a 60kN load without exceeding 100MPa of tensile stress, assuming coarse threads.
Report
Share
Report
Share
Recommended
8. Cantilever with UDL
Modeling and Analysis Lab
Problem-8 solution: Static analysis of cantilever beam subjected to UDL using ANSYS
5. Truss element
The document provides information about determining nodal displacements and stresses in members of a two bar truss shown in a figure. It gives the modulus of elasticity, member area, nodal displacements, and calculates the theoretical stress in a member based on the given displacements and modulus to compare to the finite element method result.
22564 emd 2.1 cotter joint numerical
The document describes the design of a cotter joint to withstand a maximum tensile load of 6KN. It provides definitions of the variables involved in the joint design. It then outlines 10 steps to size the different parts of the joint based on the material properties and load value, determining values for the diameters, thicknesses, and distances. The final section provides the results of the full design process.
6. Truss element 2
The document describes analyzing a four bar truss to determine its deformation, maximum stress, and reaction forces. The truss is made of elements that each have a modulus of elasticity of 29.5 GPa and cross-sectional area of 1 square meter. The results show a deformation of -22.25 mm, a stress of 4167 N/mm^2, and reactions forces of Fx = 4167 N and Fy = 3126 N. These results are then validated by comparing to results from ANSYS simulations.
Design of Temporary and Permanent Joints
This document discusses different types of temporary and permanent joints used in structures, including bolted joints, knuckle joints, cotter joints, welded joints, and riveted joints. It specifically focuses on eccentrically loaded riveted joints and provides examples of calculating the size of rivets needed based on the load and permissible stresses.
Design of springs and levers
The document discusses problems related to the design of helical springs, leaf springs, and coned disc springs. It provides examples of spring design problems involving the calculation of spring dimensions, loads, stresses, and deflections given various input parameters such as material properties, load ranges, spring indices, and dimensional constraints. The problems cover topics such as determining wire diameter, number of coils, spring rates, thicknesses of leaf springs, and stresses induced in coned disc springs. Solutions to the problems are presented using relevant spring design equations.
Flanged beams analysis - type 2
RCC design, Analysis of flanged beam, T beam, anna university, CE8501, Moment of resistance, neutral axis depth, Civil Engineering, design of beams, limit state method, IS 456, SP 16
22564 emd 1.2 numericals
This document contains 3 engineering design problems involving calculations to determine the necessary dimensions of mechanical components based on given load and stress criteria:
1) Calculate the diameter of a connecting rod given a load of 65kN and maximum tensile stress of 35N/mm^2.
2) Find the minimum punch diameter for a hole in a 20mm thick steel plate under a 380kN force and 300N/mm^2 ultimate shear strength.
3) Determine the suitable diameter of a single eye end on a tractor trolley under a 25kN load based on a maximum bearing pressure of 12N/mm^2.
Recommended
8. Cantilever with UDL
Modeling and Analysis Lab
Problem-8 solution: Static analysis of cantilever beam subjected to UDL using ANSYS
5. Truss element
The document provides information about determining nodal displacements and stresses in members of a two bar truss shown in a figure. It gives the modulus of elasticity, member area, nodal displacements, and calculates the theoretical stress in a member based on the given displacements and modulus to compare to the finite element method result.
22564 emd 2.1 cotter joint numerical
The document describes the design of a cotter joint to withstand a maximum tensile load of 6KN. It provides definitions of the variables involved in the joint design. It then outlines 10 steps to size the different parts of the joint based on the material properties and load value, determining values for the diameters, thicknesses, and distances. The final section provides the results of the full design process.
6. Truss element 2
The document describes analyzing a four bar truss to determine its deformation, maximum stress, and reaction forces. The truss is made of elements that each have a modulus of elasticity of 29.5 GPa and cross-sectional area of 1 square meter. The results show a deformation of -22.25 mm, a stress of 4167 N/mm^2, and reactions forces of Fx = 4167 N and Fy = 3126 N. These results are then validated by comparing to results from ANSYS simulations.
Design of Temporary and Permanent Joints
This document discusses different types of temporary and permanent joints used in structures, including bolted joints, knuckle joints, cotter joints, welded joints, and riveted joints. It specifically focuses on eccentrically loaded riveted joints and provides examples of calculating the size of rivets needed based on the load and permissible stresses.
Design of springs and levers
The document discusses problems related to the design of helical springs, leaf springs, and coned disc springs. It provides examples of spring design problems involving the calculation of spring dimensions, loads, stresses, and deflections given various input parameters such as material properties, load ranges, spring indices, and dimensional constraints. The problems cover topics such as determining wire diameter, number of coils, spring rates, thicknesses of leaf springs, and stresses induced in coned disc springs. Solutions to the problems are presented using relevant spring design equations.
Flanged beams analysis - type 2
RCC design, Analysis of flanged beam, T beam, anna university, CE8501, Moment of resistance, neutral axis depth, Civil Engineering, design of beams, limit state method, IS 456, SP 16
22564 emd 1.2 numericals
This document contains 3 engineering design problems involving calculations to determine the necessary dimensions of mechanical components based on given load and stress criteria:
1) Calculate the diameter of a connecting rod given a load of 65kN and maximum tensile stress of 35N/mm^2.
2) Find the minimum punch diameter for a hole in a 20mm thick steel plate under a 380kN force and 300N/mm^2 ultimate shear strength.
3) Determine the suitable diameter of a single eye end on a tractor trolley under a 25kN load based on a maximum bearing pressure of 12N/mm^2.
Fff
The document summarizes the design of parts for a hydraulic cylinder, including:
1) The piston rod is designed to be 20mm in diameter to withstand compressive stresses under a 19,600N load. Buckling analysis confirms the design is safe.
2) The cylinder is designed to be 50mm in outer diameter to withstand internal pressures up to 9.98MPa. Wall thickness is calculated as 3mm to resist hoop and longitudinal stresses.
3) A rubber pipe is designed with a thickness of 4mm to withstand an internal pressure of 9.8MPa over its 500mm length.
Flanged beams analysis - type 3
RCC design, Analysis of flanged beam, T beam, anna university, CE8501, Moment of resistance, neutral axis depth, Civil Engineering, design of beams, limit state method, IS 456, SP 16
Shearing&BearingMEC32
Shear stress is calculated by dividing the shear load by the area it acts upon. It can also be expressed as the total surface parallel load divided by the area.
An example calculates the width of a key preventing a pulley from rotating on a shaft under a given torque, by determining the shear force and dividing by the area of the key.
Bearing stress is calculated by dividing the bearing load by the bearing contact area, which can also be expressed by dividing the load by the product of the width and height of the bearing area.
Shearing (1)
Shear stress is caused by forces acting parallel to the surface of an object. The shear stress τ can be calculated using the equation τ = V/A, where V is the shear load and A is the cross-sectional area resisting the force. Shear stress is illustrated in examples involving determining the width of a key connecting a pulley to a shaft and calculating the minimum diameter of a pin connecting structural members.
Design of fasteners and welded joints
The document contains several examples of calculating weld sizes and bolt sizes for different welded and bolted joints. The examples involve calculating shear stresses in welds due to direct loads and bending moments and determining necessary weld sizes. They also involve calculating bolt sizes for different bolted joints based on allowable shear stresses and safety factors. The final example calculates the necessary bolt size for connecting a steam engine cylinder head based on the steam pressure, cylinder dimensions, bolt material properties, and a preload on the bolts.
H#8
The document contains solutions to multiple problems involving determining stresses and angles of twist in shafts with various cross sectional shapes when subjected to torques. The problems calculate shear stresses at different points in the shafts using equations relating torque, shear stress, area, and moment of inertia. Ratios of shear stresses and angles of twist between different shaft designs are also determined.
3 bending stress-asgn
The document describes analyzing a cantilever beam that is subjected to a 100 kN.m moment at its free end, including calculating reactions, drawing shear force and bending moment diagrams, determining bending stresses at various points, and sketching the bending stress distribution over the beam's depth. The beam's cross section and dimensions are provided, along with the steps to calculate its neutral axis, moment of inertia, and bending stresses at points A, B, C, and D.
22564 emd 2.0 direct and bending
The document provides information to calculate the width and depth of a rectangular beam subjected to a bending load. It is given that the beam carries a 400 N load at a 300 mm distance from its fixed end, and the maximum bending stress is 40 MPa. Using the bending stress formula and setting the section modulus equal to the product of depth and width/2, the width is calculated to be 16.5 mm and depth to be 2 * width = 33 mm.
H.w. #7
The document contains solutions to multiple problems involving determining shear stress, torque, and angle of twist in shaft and rod systems. Key details include formulas for calculating shear stress given torque and geometry, determining required diameters to not exceed allowable stress, and calculating angle of twist between sections using torque, length, shear modulus, and polar second moment of area. Examples analyze hollow and solid shafts made of materials like steel, brass, and aluminum under different torque conditions.
dESCRIPCION DEL PENDULO
This document describes an experiment to analyze the kinematic parameters of a simple pendulum. Materials used include a wood base, PVC tubing, a mass, string, and other components to construct the pendulum. The period of oscillation was measured and used to calculate angular frequency via two different methods, yielding similar results. Equations of motion were then used to determine displacement, velocity, and acceleration as functions of time, populating a table of kinematic parameters over one period. A graph shows the pendulum's motion matches that of simple harmonic motion.
Flanged beams design for t beam
RCC design, design of flanged beam, T beam, anna university, CE8501, Moment of resistance, neutral axis depth, Civil Engineering, design of beams, limit state method, IS 456, SP 16
Problemas esfuerzos en vigas
Se presenta la solución de varios problemas sobre el análisis de esfuerzos en vigas, normales por flexión y cortante, aplicando los conceptos básicos de la mecánica de materiales
The Knuckle Joint Assembly
The document details the design of a knuckle joint to transmit 150kN of force while meeting various design stress limits. Mathematical calculations are shown to determine the optimal diameters and thicknesses for the rod, pin, eye, and fork components to prevent failure under tensile, compressive, shear, and crushing stresses. The final dimensions selected are: rod diameter of 48.86mm, pin diameter of 43.7mm, outer eye diameter of 97.72mm, eye thickness of 61.075mm, and fork thickness of 36.64mm. Diagrams of the knuckle joint assembly and its components are provided.
Shear force bending moment diagrams
The document provides step-by-step instructions for drawing the shear force and bending moment diagrams of a cantilever beam subjected to various loads. It first finds the reactions at the support, then draws the shear force diagram showing the shear force values change from -45 kN to -75 kN over the length of the beam. It then draws the bending moment diagram, indicating the bending moment values change from -33.75 kN.m to -168.75 kN.m at the end of the beam due to the applied loads and moments. Key points on both diagrams are indicated.
0804 ch 8 day 4
This document provides instruction on graphing polar equations. It begins by reviewing polar coordinate planes and then demonstrates how to graph the equation r = 3sinθ by hand. Values for θ and the corresponding r are calculated and plotted. The graph is then drawn on polar graph paper. The document then shows how to graph the same equation using a calculator in both radian and degree mode. Several other example polar equations are presented with the appropriate window settings. Tomorrow's lesson will cover specific families of polar equations.
Mit2 092 f09_lec13
All of material inside is un-licence, kindly use it for educational only but please do not to commercialize it.
Based on 'ilman nafi'an, hopefully this file beneficially for you.
Thank you.
Solid mechanics 1 BDA 10903
The document provides solutions to multiple mechanics of materials problems involving stress, strain, modulus of elasticity, yield strength, tensile strength, and ductility calculations for various materials like bronze, brass, and aluminum alloys. It includes determining maximum loads and deformations based on stress-strain curves, computing engineering and true stress-strain values, and using stress-strain data to find the true stress required for a given true plastic strain. Diagrams of stress-strain curves are generated from the data provided in the problems.
Tem
TEM Transmission lines' properties, the construction techniques, types, uses in the circuits, mathematical representation, limitations and their solutions are described
Doubly reinforced beam design
doubly reinforced beam ,ast ,ast problems ,area of steel ,is456 ,sp16 ,beam ,mu ,mulim ,steel area ,anna university ,civil engineering
Bars subjected to multiple loads
The document discusses deformation of axially loaded bars. It defines key terms like stress, strain, Hooke's law, stiffness, compliance, and axial rigidity. It also describes how to calculate deformation of bars with multiple loads or non-uniform properties by dividing the bar into segments and using the principle of superposition. Several example problems are given to illustrate calculating deformation of bars under different loading conditions.
7 breakeven analysis
Breakeven analysis examines the relationship between costs, revenue, output levels, and profit. It is used for short-term planning and decision making. The breakeven point is where a company makes neither a profit nor loss. It can be calculated using the contribution per unit and fixed costs. Margin of safety measures the difference between budgeted sales and breakeven sales. Breakeven analysis can determine the level of sales needed to break even or make a target profit.
6 fixed assets, current assets, depreciation methods
This document provides an overview of basic financial accounting concepts. It defines key accounting terms like accounts, accounting, assets, liabilities, equity, revenue, and expenses. It describes the double-entry system of accounting and the accounting cycle of recording transactions in journals, posting to ledgers, preparing a trial balance, and developing financial statements. It also outlines accounting concepts, conventions, the different bases of accounting, and the types and roles of various accounts.
More Related Content
What's hot
Fff
The document summarizes the design of parts for a hydraulic cylinder, including:
1) The piston rod is designed to be 20mm in diameter to withstand compressive stresses under a 19,600N load. Buckling analysis confirms the design is safe.
2) The cylinder is designed to be 50mm in outer diameter to withstand internal pressures up to 9.98MPa. Wall thickness is calculated as 3mm to resist hoop and longitudinal stresses.
3) A rubber pipe is designed with a thickness of 4mm to withstand an internal pressure of 9.8MPa over its 500mm length.
Flanged beams analysis - type 3
RCC design, Analysis of flanged beam, T beam, anna university, CE8501, Moment of resistance, neutral axis depth, Civil Engineering, design of beams, limit state method, IS 456, SP 16
Shearing&BearingMEC32
Shear stress is calculated by dividing the shear load by the area it acts upon. It can also be expressed as the total surface parallel load divided by the area.
An example calculates the width of a key preventing a pulley from rotating on a shaft under a given torque, by determining the shear force and dividing by the area of the key.
Bearing stress is calculated by dividing the bearing load by the bearing contact area, which can also be expressed by dividing the load by the product of the width and height of the bearing area.
Shearing (1)
Shear stress is caused by forces acting parallel to the surface of an object. The shear stress τ can be calculated using the equation τ = V/A, where V is the shear load and A is the cross-sectional area resisting the force. Shear stress is illustrated in examples involving determining the width of a key connecting a pulley to a shaft and calculating the minimum diameter of a pin connecting structural members.
Design of fasteners and welded joints
The document contains several examples of calculating weld sizes and bolt sizes for different welded and bolted joints. The examples involve calculating shear stresses in welds due to direct loads and bending moments and determining necessary weld sizes. They also involve calculating bolt sizes for different bolted joints based on allowable shear stresses and safety factors. The final example calculates the necessary bolt size for connecting a steam engine cylinder head based on the steam pressure, cylinder dimensions, bolt material properties, and a preload on the bolts.
H#8
The document contains solutions to multiple problems involving determining stresses and angles of twist in shafts with various cross sectional shapes when subjected to torques. The problems calculate shear stresses at different points in the shafts using equations relating torque, shear stress, area, and moment of inertia. Ratios of shear stresses and angles of twist between different shaft designs are also determined.
3 bending stress-asgn
The document describes analyzing a cantilever beam that is subjected to a 100 kN.m moment at its free end, including calculating reactions, drawing shear force and bending moment diagrams, determining bending stresses at various points, and sketching the bending stress distribution over the beam's depth. The beam's cross section and dimensions are provided, along with the steps to calculate its neutral axis, moment of inertia, and bending stresses at points A, B, C, and D.
22564 emd 2.0 direct and bending
The document provides information to calculate the width and depth of a rectangular beam subjected to a bending load. It is given that the beam carries a 400 N load at a 300 mm distance from its fixed end, and the maximum bending stress is 40 MPa. Using the bending stress formula and setting the section modulus equal to the product of depth and width/2, the width is calculated to be 16.5 mm and depth to be 2 * width = 33 mm.
H.w. #7
The document contains solutions to multiple problems involving determining shear stress, torque, and angle of twist in shaft and rod systems. Key details include formulas for calculating shear stress given torque and geometry, determining required diameters to not exceed allowable stress, and calculating angle of twist between sections using torque, length, shear modulus, and polar second moment of area. Examples analyze hollow and solid shafts made of materials like steel, brass, and aluminum under different torque conditions.
dESCRIPCION DEL PENDULO
This document describes an experiment to analyze the kinematic parameters of a simple pendulum. Materials used include a wood base, PVC tubing, a mass, string, and other components to construct the pendulum. The period of oscillation was measured and used to calculate angular frequency via two different methods, yielding similar results. Equations of motion were then used to determine displacement, velocity, and acceleration as functions of time, populating a table of kinematic parameters over one period. A graph shows the pendulum's motion matches that of simple harmonic motion.
Flanged beams design for t beam
RCC design, design of flanged beam, T beam, anna university, CE8501, Moment of resistance, neutral axis depth, Civil Engineering, design of beams, limit state method, IS 456, SP 16
Problemas esfuerzos en vigas
Se presenta la solución de varios problemas sobre el análisis de esfuerzos en vigas, normales por flexión y cortante, aplicando los conceptos básicos de la mecánica de materiales
The Knuckle Joint Assembly
The document details the design of a knuckle joint to transmit 150kN of force while meeting various design stress limits. Mathematical calculations are shown to determine the optimal diameters and thicknesses for the rod, pin, eye, and fork components to prevent failure under tensile, compressive, shear, and crushing stresses. The final dimensions selected are: rod diameter of 48.86mm, pin diameter of 43.7mm, outer eye diameter of 97.72mm, eye thickness of 61.075mm, and fork thickness of 36.64mm. Diagrams of the knuckle joint assembly and its components are provided.
Shear force bending moment diagrams
The document provides step-by-step instructions for drawing the shear force and bending moment diagrams of a cantilever beam subjected to various loads. It first finds the reactions at the support, then draws the shear force diagram showing the shear force values change from -45 kN to -75 kN over the length of the beam. It then draws the bending moment diagram, indicating the bending moment values change from -33.75 kN.m to -168.75 kN.m at the end of the beam due to the applied loads and moments. Key points on both diagrams are indicated.
0804 ch 8 day 4
This document provides instruction on graphing polar equations. It begins by reviewing polar coordinate planes and then demonstrates how to graph the equation r = 3sinθ by hand. Values for θ and the corresponding r are calculated and plotted. The graph is then drawn on polar graph paper. The document then shows how to graph the same equation using a calculator in both radian and degree mode. Several other example polar equations are presented with the appropriate window settings. Tomorrow's lesson will cover specific families of polar equations.
Mit2 092 f09_lec13
All of material inside is un-licence, kindly use it for educational only but please do not to commercialize it.
Based on 'ilman nafi'an, hopefully this file beneficially for you.
Thank you.
Solid mechanics 1 BDA 10903
The document provides solutions to multiple mechanics of materials problems involving stress, strain, modulus of elasticity, yield strength, tensile strength, and ductility calculations for various materials like bronze, brass, and aluminum alloys. It includes determining maximum loads and deformations based on stress-strain curves, computing engineering and true stress-strain values, and using stress-strain data to find the true stress required for a given true plastic strain. Diagrams of stress-strain curves are generated from the data provided in the problems.
Tem
TEM Transmission lines' properties, the construction techniques, types, uses in the circuits, mathematical representation, limitations and their solutions are described
Doubly reinforced beam design
doubly reinforced beam ,ast ,ast problems ,area of steel ,is456 ,sp16 ,beam ,mu ,mulim ,steel area ,anna university ,civil engineering
Bars subjected to multiple loads
The document discusses deformation of axially loaded bars. It defines key terms like stress, strain, Hooke's law, stiffness, compliance, and axial rigidity. It also describes how to calculate deformation of bars with multiple loads or non-uniform properties by dividing the bar into segments and using the principle of superposition. Several example problems are given to illustrate calculating deformation of bars under different loading conditions.
What's hot (20)
More from Dr.R. SELVAM
7 breakeven analysis
Breakeven analysis examines the relationship between costs, revenue, output levels, and profit. It is used for short-term planning and decision making. The breakeven point is where a company makes neither a profit nor loss. It can be calculated using the contribution per unit and fixed costs. Margin of safety measures the difference between budgeted sales and breakeven sales. Breakeven analysis can determine the level of sales needed to break even or make a target profit.
6 fixed assets, current assets, depreciation methods
This document provides an overview of basic financial accounting concepts. It defines key accounting terms like accounts, accounting, assets, liabilities, equity, revenue, and expenses. It describes the double-entry system of accounting and the accounting cycle of recording transactions in journals, posting to ledgers, preparing a trial balance, and developing financial statements. It also outlines accounting concepts, conventions, the different bases of accounting, and the types and roles of various accounts.
5 preparation and interpretation of balance sheets
The document discusses three key financial statements: the balance sheet, income statement, and statement of cash flows. The balance sheet provides a snapshot of a company's assets, liabilities, and equity at a point in time. The income statement measures revenue, expenses, and profits over a period of time. The statement of cash flows provides insight into a company's cash flow from operating, investing, and financing activities during a period. Examples of each statement are also included.
4 acounting principle
This document discusses key accounting principles and concepts. It defines generally accepted accounting principles (GAAP) as principles that have substantial authoritative support and general acceptability. It classifies accounting principles into concepts and conventions. Some key concepts discussed include going concern, consistency, and accrual assumptions as well as the accounting entity, money measurement, matching, and revenue recognition principles. The document also explains conventions like materiality, conservatism, and the dual aspect principle.
3 capital structure
The document discusses capital structure and the factors considered when determining a firm's optimal capital structure. It defines capital structure as the mix of long-term financing sources like debt, preference shares, and equity. Management should choose a capital structure that minimizes the firm's cost of capital while maximizing shareholder value. Different approaches for determining the optimal capital structure are described, including the net income, net operating income, Modigliani-Miller, and traditional intermediate approaches.
1 sources of finance
This document discusses various sources of finance for businesses. It identifies external and internal sources of finance. External sources include issuing shares, debentures, accepting public deposits, and taking loans from financial institutions and banks. Internal sources include retained profits that are reinvested in the business. Long term sources are used for fixed capital needs and include equity, debt, and retained profits. Short term sources like loans and deposits are used for working capital needs.
2 term loan
The document discusses various types of term loans and lease financing. It defines term loans as debt that is scheduled to be repaid in more than one year but generally less than ten years. Term loans typically involve regular payments of both interest and principal. The document also discusses the costs and benefits of term loans versus lease financing. It provides examples of different types of leases and factors to consider when deciding whether to lease or purchase equipment.
4 b. capital budgeting and cost analysis performance evaluation
A manager using discounted cash flow methods for capital budgeting can face conflicts if accounting rate of return is used for performance evaluation. Specifically, a project with an accounting rate of return below the desired minimum threshold will be rejected, even if it has a positive net present value using discounted cash flow methods. This goal incongruence can be reduced by evaluating managers' performance on a project-by-project basis instead of using accounting rate of return.
4 a. capital budgeting and cost analysis
1) Capital budgeting is a six-stage process that focuses on projects spanning multiple years. It involves identifying potential projects, acquiring information, selecting projects, financing them, and implementing/controlling them.
2) There are two main discounted cash flow methods for evaluating projects: net present value (NPV) and internal rate of return (IRR). NPV totals the present value of future cash flows and IRR is the discount rate that makes NPV equal to zero.
3) Other methods like payback period and accrual accounting rate of return (AARR) are also used but have limitations like not incorporating time value of money. NPV and IRR are preferable but can give different results,
3 capital budgeting
Capital budgeting is the process of analyzing projects and determining which to include in the capital budget. It involves evaluating long-term investment projects involving large capital outlays. There are various evaluation criteria used for capital budgeting including net present value (NPV), internal rate of return (IRR), payback period, discounted payback period, and profitability index. Generally, NPV is considered the best method but companies often consider multiple criteria as each provides different relevant information for decision making.
2 working capital
This document discusses working capital management. It defines working capital as the capital required to finance short-term assets such as inventory, debtors, and cash. Working capital is also known as revolving or circulating capital. It then discusses different types of working capital including gross, net, permanent, temporary, regular, reserve, and seasonal working capital. The significance and calculation of gross and net working capital is also explained.
1 current assement management
This document provides an overview of current asset management. It discusses key aspects like working capital management, current asset investment policies, cash management, marketable securities, accounts receivable management, and inventory management. The goal of current asset management is to optimize investment in current assets to balance risk and return while maintaining sufficient liquidity to meet short-term obligations.
2 b. project termination
This document discusses various ways that projects can be terminated, including extinction due to success or failure, addition through institutionalization or integration into an existing organization, and starvation through decreased funding. It also identifies common causes of project failure such as lack of support, improper staffing, and poor planning. The termination process involves a decision on whether to continue the project based on costs and expected outcomes, followed by a closeout process. Key duties for a termination manager are outlined, such as completing work, finalizing documentation and reports, redistributing resources, and closing financial records. A final report detailing project performance, administration, structure, teams and management techniques is recommended.
2 a. project auditing
A project audit evaluates the progress and performance of a project compared to its planned objectives. It examines all aspects of a project including its management, methodology, budgets, and completion status. The audit report assesses the current status, future projections, critical tasks, risks, and lessons learned. It follows a life cycle of initiation, baseline definition, data collection, analysis, reporting, and termination. The auditor maintains independence and objectivity to truthfully evaluate the project's strengths and weaknesses.
1 b, evaluation of project
This document discusses evaluation of projects. It defines evaluation as judging the worth, value or quality of a project to make necessary decisions. Key aspects of evaluation include relevance, effectiveness, efficiency, sustainability and impact. Formative evaluation is intended to improve performance during design/implementation, while summative evaluation determines outcomes at the end. Types of evaluation include participatory, process-based, outcome-based, self-evaluation and goal-based. Evaluation provides strategic, operational and learning information. Principles, stages, criteria, types, methods and views of evaluation are also outlined.
1 a, monitoring and evaluation of PM
This document discusses monitoring and evaluation of projects. It defines a project as having a rationale, goal, objectives, action plan, beneficiaries, time frame, budget, and outputs. It states that monitoring involves systematically recording observations, gathering information, analyzing data, documenting findings, reflecting on progress, and taking action or re-planning if needed. The goal of monitoring is to ensure inputs, activities, and outputs proceed according to plan and that the right things are being delivered to the right people at the right time through the correct processes.
3 industrial hydraulic circuits shapping, milling, drilling
The document describes several hydraulic circuits used in industrial machinery. It summarizes the hydraulic circuits for a milling machine, shaper machine, surface grinder, hydraulic press, hydraulic power steering, dump trucks, and excavators. For each, it outlines the key components of the circuit such as pumps, valves, cylinders, and how fluid flow is directed to enable the motion of machine parts like tables, rams, and booms.
2 maintenance of hydraulic systems
This document discusses best practices for maintaining hydraulic systems. It emphasizes that contamination control is the number one priority, and outlines various causes of contamination and failures in hydraulic systems. The document recommends developing an effective preventative maintenance and predictive maintenance program for hydraulic systems, with a focus on failure mode identification and mitigation. It also stresses the importance of education in hydraulic fundamentals, maintenance, and troubleshooting. Measurement of hydraulic system reliability is advised.
1 hydraulic troubleshooting
The document provides guidance on troubleshooting hydraulic systems. It discusses developing a systematic process including following safety procedures, obtaining documentation, isolating issues, and making predictive checks. Common problems involve pumps, valves, actuators, and overheating. Pump issues include noise, pressure/flow problems. Valves and actuators may cause low/erratic pressure or slow movement. Overheating can indicate contamination, relief settings, or internal leaks. Electrical issues can similarly impact hydraulics. Accumulators and proportional valves require specialized documentation. The key tools are the senses - sight, sound, touch, and smell.
3 c. industrial pneumatic circuit logic
This document discusses various pneumatic logic circuits that can be created using spool valves. It describes logic AND, OR, NOT, memory/latch circuits and how they function. Diagrams are provided to illustrate 3/2 valves that can be used for normally open, normally closed, selection, and diversion applications. Circuits for OR, AND, NOT logic functions and single pulse creation are also depicted.
More from Dr.R. SELVAM (20)
6 fixed assets, current assets, depreciation methods
6 fixed assets, current assets, depreciation methods
5 preparation and interpretation of balance sheets
5 preparation and interpretation of balance sheets
4 b. capital budgeting and cost analysis performance evaluation
4 b. capital budgeting and cost analysis performance evaluation
3 industrial hydraulic circuits shapping, milling, drilling
3 industrial hydraulic circuits shapping, milling, drilling
Recently uploaded
How to Fix the Import Error in the Odoo 17
An import error occurs when a program fails to import a module or library, disrupting its execution. In languages like Python, this issue arises when the specified module cannot be found or accessed, hindering the program's functionality. Resolving import errors is crucial for maintaining smooth software operation and uninterrupted development processes.
A Survey of Techniques for Maximizing LLM Performance.pptx
A Survey of Techniques for Maximizing LLM Performance
Introduction to AI for Nonprofits with Tapp Network
Dive into the world of AI! Experts Jon Hill and Tareq Monaur will guide you through AI's role in enhancing nonprofit websites and basic marketing strategies, making it easy to understand and apply.
RPMS TEMPLATE FOR SCHOOL YEAR 2023-2024 FOR TEACHER 1 TO TEACHER 3
RPMS Template 2023-2024 by: Irene S. Rueco
Digital Artifact 1 - 10VCD Environments Unit
Digital Artifact 1 - 10VCD Environments Unit - NGV Pavilion Concept Design
How to Build a Module in Odoo 17 Using the Scaffold Method
Odoo provides an option for creating a module by using a single line command. By using this command the user can make a whole structure of a module. It is very easy for a beginner to make a module. There is no need to make each file manually. This slide will show how to create a module using the scaffold method.
Thesis Statement for students diagnonsed withADHD.ppt
Presentation required for the master in Education.
Pollock and Snow "DEIA in the Scholarly Landscape, Session One: Setting Expec...
Pollock and Snow "DEIA in the Scholarly Landscape, Session One: Setting Expec...National Information Standards Organization (NISO)
This presentation was provided by Steph Pollock of The American Psychological Association’s Journals Program, and Damita Snow, of The American Society of Civil Engineers (ASCE), for the initial session of NISO's 2024 Training Series "DEIA in the Scholarly Landscape." Session One: 'Setting Expectations: a DEIA Primer,' was held June 6, 2024.Chapter 4 - Islamic Financial Institutions in Malaysia.pptx
Chapter 4 - Islamic Financial Institutions in Malaysia.pptxMohd Adib Abd Muin, Senior Lecturer at Universiti Utara Malaysia
This slide is special for master students (MIBS & MIFB) in UUM. Also useful for readers who are interested in the topic of contemporary Islamic banking.
A Strategic Approach: GenAI in Education
Artificial Intelligence (AI) technologies such as Generative AI, Image Generators and Large Language Models have had a dramatic impact on teaching, learning and assessment over the past 18 months. The most immediate threat AI posed was to Academic Integrity with Higher Education Institutes (HEIs) focusing their efforts on combating the use of GenAI in assessment. Guidelines were developed for staff and students, policies put in place too. Innovative educators have forged paths in the use of Generative AI for teaching, learning and assessments leading to pockets of transformation springing up across HEIs, often with little or no top-down guidance, support or direction.
This Gasta posits a strategic approach to integrating AI into HEIs to prepare staff, students and the curriculum for an evolving world and workplace. We will highlight the advantages of working with these technologies beyond the realm of teaching, learning and assessment by considering prompt engineering skills, industry impact, curriculum changes, and the need for staff upskilling. In contrast, not engaging strategically with Generative AI poses risks, including falling behind peers, missed opportunities and failing to ensure our graduates remain employable. The rapid evolution of AI technologies necessitates a proactive and strategic approach if we are to remain relevant.
Top five deadliest dog breeds in America
Thinking of getting a dog? Be aware that breeds like Pit Bulls, Rottweilers, and German Shepherds can be loyal and dangerous. Proper training and socialization are crucial to preventing aggressive behaviors. Ensure safety by understanding their needs and always supervising interactions. Stay safe, and enjoy your furry friends!
Advantages and Disadvantages of CMS from an SEO Perspective
Advantages and Disadvantages of CMS from an SEO Perspective
DRUGS AND ITS classification slide share
Any substance (other than food) that is used to prevent, diagnose, treat, or relieve symptoms of a
disease or abnormal condition
Your Skill Boost Masterclass: Strategies for Effective Upskilling
Your Skill Boost Masterclass: Strategies for Effective UpskillingExcellence Foundation for South Sudan
Strategies for Effective Upskilling is a presentation by Chinwendu Peace in a Your Skill Boost Masterclass organisation by the Excellence Foundation for South Sudan on 08th and 09th June 2024 from 1 PM to 3 PM on each day.Recently uploaded (20)
A Survey of Techniques for Maximizing LLM Performance.pptx
A Survey of Techniques for Maximizing LLM Performance.pptx
Introduction to AI for Nonprofits with Tapp Network
Introduction to AI for Nonprofits with Tapp Network
RPMS TEMPLATE FOR SCHOOL YEAR 2023-2024 FOR TEACHER 1 TO TEACHER 3
RPMS TEMPLATE FOR SCHOOL YEAR 2023-2024 FOR TEACHER 1 TO TEACHER 3
How to Build a Module in Odoo 17 Using the Scaffold Method
How to Build a Module in Odoo 17 Using the Scaffold Method
Film vocab for eal 3 students: Australia the movie
Film vocab for eal 3 students: Australia the movie
Thesis Statement for students diagnonsed withADHD.ppt
Thesis Statement for students diagnonsed withADHD.ppt
Pollock and Snow "DEIA in the Scholarly Landscape, Session One: Setting Expec...
Pollock and Snow "DEIA in the Scholarly Landscape, Session One: Setting Expec...
Chapter 4 - Islamic Financial Institutions in Malaysia.pptx
Chapter 4 - Islamic Financial Institutions in Malaysia.pptx
Advantages and Disadvantages of CMS from an SEO Perspective
Advantages and Disadvantages of CMS from an SEO Perspective
Your Skill Boost Masterclass: Strategies for Effective Upskilling
Your Skill Boost Masterclass: Strategies for Effective Upskilling
Group Presentation 2 Economics.Ariana Buscigliopptx
Group Presentation 2 Economics.Ariana Buscigliopptx
1 b. Threaded fasteners and powers screws examples
- 2. Example 1
- 3. Example 2
- 4. Example 2
- 5. Example 3
- 6. Example 2 Two machine parts are fastened together tightly by means of a 24 mm tap bolt. If the load tending to separate these parts is neglected, find the stress that is set up in the bolt by the initial tightening.
- 7. Example 5: An eye bolt is to be used for lifting a load of 60 kN. Find the nominal diameter of the bolt, if the tensile stress is not to exceed 100 MPa. Assume coarse threads. Solution. Given : P = 60 kN = 60 × 103 N ; s= 100 MPa = 100 N/mm2 An eye bolt for lifting a load is shown in Fig. Let d = Nominal diameter of the bolt, and dc = Core diameter of the bolt. We know that load on the bolt (P),