resume

1. M V RAVI KIRAN
Senior Engineer – Mechanical Design
Experience: 3 Years
Bangalore | 7382048781 | vrkmeesala93@gmail.com
Summary
Sr. Mechanical Design Engineer with M.Tech from IIT having experience in new product development
of complex mechanical systems for Defense sector. Skilled in Heavy Weldment Structures Design,
Design of mechanisms for Material Handling Equipment, Drive Train Design, GD&T, 1-D Tol. Stack up,
Drafting. Gained knowledge in Missile Launchers, Artillery Gun Systems & Sonar Winch Systems.
Experience
Sr. ENGINEER – Mechanical Design| TATA POWER STRATEGIC
ENGINEERING DIVISION | 23rd
March, 2017 to till date – Bengaluru
 Evaluating Customer Specifications and preparing Requirement
Capture Document (RCD).
 Configuration evaluation, Development of Electro-Mechanical
Systems for Heavy Engineering.
 Performing Engineering Calculations using Machine Design
Concepts. Developing Linkages, Kinematics Design, Speed
Reducer, Lifting Device using Power Screws & performing
Motion Analysis.
 Design & Development of Welded Structures.
 Knowledge of Commonly available metallic raw materials (BS
970, DIN, IS Standards), Heat Treatment & Coatings.
 Communicating with FEA Team & Process Team to ensure the
Design meet Product, Process & Quality Requirements.
 Working Knowledge of Mechanical Component Selection
(Bearings, Roller Screws, Springs etc.),
 Preparing Preliminary Design Report (PDR), Testing
Requirements (ATP), DFMEA for Sub-Assemblies.
 Reviewing Manufacturing Drawings, Bill of Materials.
 Handling engineering change management in PLM.
 Clearing Drawing Clarifications and deviations raised by
manufacturing Vendor.
 Assist System integration for System readiness and QA for
factory acceptance tests (FAT) at prototyping stage, trails.
Skills
 CAD Modelling: Solid Edge, NX
 PLM: Team center
 Engineering Calculations: Mathcad,
Kissoft, Geometric Stackup
Education
M.Tech | 2016 | IIT (ISM), DHANBAD
· CGPA 8.69 / 10
· Major: Mechanical (Machine Design)
· Related coursework: Kinematics &
Dynamics of Machinery, Fracture
Mechanics
B.Tech| 2014 | BAPATLA ENGINEERING
COLLEGE (AUTONOMOUS)
· CGPA 8.32 / 10
· Major: Mechanical
Certifications
 Design of Manufacture and Assembly -
IMTMA, Bengaluru - May 2017
A numerical study on effects of friction-
induced thermal load for rail under
varied wheel slip conditions, In:
SIMULATION: Transactions of The
Society for Modeling and Simulation
International, July, 2018.
Numerical investigation of Ratchetting
Behavior in Rail Steel under Cyclic
Rolling-Sliding contact, In: Procedia
Engineering, Volume 173, 2017.
Publications

2. Project: ADVANCED TOWED ARTILLERY GUN SYSTEM 155mm for Indian Army
 Fabricated Structural Design of Chassis which is a critical load bearing member of Gun
Undercarriage. Worked closely with FEA Team to deliver failure proof design at Firing,
Transportation & Towing Modes of Gun.
 Design of Light Weight Walking Beam structure to improve towing stability in rough
terrain.
 Test Setup for Load Testing of Draw Bar Screw Jack.
 Troubleshooting of Breech Mechanism & resolving Automatic Primer Loading by
introduction of new Mechanism.
 Analyzing Failure modes in Damaged Springs (Spiral Torsion Springs) & providing
Solutions.
 Development of Indigenous Roller Screw & Ball Screw Linear Actuators for various
operations in the Gun system.
 Preparing Test Plan for Actuators Validation in Actuator Test Setup.
Project: DEPLOYMENT MECHANISM FOR PORTABLE DIVER DETECTION SONAR
(DAVIT CRANE) – Indian Navy
 Handled the execution of the project from Design end.
 Revision of Detailed Design Report and Quality Acceptance Plans.
 Conducting Ship Survey for feasibility of installation of PDDS at INS – Jalashwa
(Amphibious Warfare Ship).
 Providing Low Cost Solution for Deployment Mechanism.
 Direct Handling with Manufacturing Vendor to ensure deadlines are met without
compromising on the quality of the solution.
 Gained Knowledge on surface coatings (Galvanizing, Electrolytic plating’s) for Marine
requirements.
 Involved in Cross Functional Team (CFT) meetings for manufacturing readiness.
Project: PINAKA ROCKET LAUNCHER - Indian Army
 Designed & Developed Roller Screw Elevation Actuator for elevation of Cradle Assembly.
 Designed Spiral Bevel Gear Box for Actuator.
 Preparing Acceptance Test Procedures for Actuator.
Project: ELECTROMECHANICAL ACTUATOR TEST SETUP
 Actuator Test setup was designed for Performance testing of Electromechanical Linear
Actuators.
 Design of necessary fixtures for Testing of Electro Mechanical Linear Actuators.
Projects/Achievements