remote operating system installation Remote Installation Services (RIS) ships as a part of the Windows® 2000 Server software system. This document outlines the steps necessary to put in, configure, and use RIS. RIS was designed to cut back the prices incurred by pre-installing or physically visiting every consumer pc to put in the software system (OS). By combining RIS with alternative Windows 2000 IntelliMirror™ management technologies features—User knowledge Management, software package Installation and Maintenance, and User Settings Management—companies get pleasure from higher disaster recovery with easier OS and application management. Prerequisites See Appendix A below to confirm that each your server and consumer hardware meet the remote installation hardware necessities. The drive on the server wherever you decide on to put in RIS should be formatted with the NTFS filing system. RIS needs a big quantity of space and can\'t be put in on constant drive or partition on that Windows 2000 Server is put in. make sure that the chosen drive contains enough free space for a minimum of one full Windows 2000 skilled compact disc—a minimum of roughly 800 megabytes (MB)–1 GB (GB). RIS needs many alternative services that conjointly ship as a part of Windows 2000 Server. These services will be put in on individual servers, or all on one server, counting on your network design: Domain Name Service (DNS) Server. Remote installation depends on DNS for locating the directory service and consumer machine accounts. you\'ll use any Windows 2000 Active DirectoryTM service-compliant DNS server, otherwise you will use the DNS server given Windows 2000 Server. Dynamic Host Configuration Protocol (DHCP) Server. RIS needs a DHCP server to be gift and active on the network. The remote boot-enabled consumer computers receive AN information processing address from the DHCP server before contacting RIS. Active Directory. RIS depends on Windows 2000 Active Directory for locating existing consumer machines further as existing RIS servers. RIS should be put in on a Windows 2000- based server that has access to Active Directory. this will be a site controller or a server that\'s a member of a site with access to the Active Directory. To ensure a in installation, you want to install and tack together the extra services delineate higher than so as for RIS to perform. additionally, certify that you just have each the Windows 2000 Server and skilled CDs on the market. Before starting this gradual guide, you wish to create the common infrastructure, that specifies a specific hardware and software package configuration. The common infrastructure is roofed within the Common Infrastructure gradual guide, \"Part 1: putting in a Windows 2000 Server as a site Controller\" http://www.microsoft.com/windows2000/techinfo/planning/server/serversteps.asp. If you\'re not victimization the common infrastructure, you wish to create the suitable changes to the current instruction set. Alth.

1. remote operating system installation
Remote Installation Services (RIS) ships as a part of the Windows® 2000 Server software
system. This document outlines the steps necessary to put in, configure, and use RIS.
RIS was designed to cut back the prices incurred by pre-installing or physically visiting every
consumer pc to put in the software system (OS). By combining RIS with alternative Windows
2000 IntelliMirror™ management technologies features—User knowledge Management,
software package Installation and Maintenance, and User Settings Management—companies get
pleasure from higher disaster recovery with easier OS and application management.
Prerequisites
See Appendix A below to confirm that each your server and consumer hardware meet the
remote installation hardware necessities.
The drive on the server wherever you decide on to put in RIS should be formatted with the
NTFS filing system. RIS needs a big quantity of space and can't be put in on constant drive or
partition on that Windows 2000 Server is put in. make sure that the chosen drive contains enough
free space for a minimum of one full Windows 2000 skilled compact disc—a minimum of
roughly 800 megabytes (MB)–1 GB (GB).
RIS needs many alternative services that conjointly ship as a part of Windows 2000 Server.
These services will be put in on individual servers, or all on one server, counting on your
network design:
Domain Name Service (DNS) Server. Remote installation depends on DNS for locating the
directory service and consumer machine accounts. you'll use any Windows 2000 Active
DirectoryTM service-compliant DNS server, otherwise you will use the DNS server given
Windows 2000 Server.
Dynamic Host Configuration Protocol (DHCP) Server. RIS needs a DHCP server to be gift and
active on the network. The remote boot-enabled consumer computers receive AN information
processing address from the DHCP server before contacting RIS.
Active Directory. RIS depends on Windows 2000 Active Directory for locating existing
consumer machines further as existing RIS servers. RIS should be put in on a Windows 2000-
based server that has access to Active Directory. this will be a site controller or a server that's a
member of a site with access to the Active Directory.
To ensure a in installation, you want to install and tack together the extra services delineate
higher than so as for RIS to perform. additionally, certify that you just have each the Windows
2000 Server and skilled CDs on the market.
Before starting this gradual guide, you wish to create the common infrastructure, that specifies a
specific hardware and software package configuration. The common infrastructure is roofed

2. within the Common Infrastructure gradual guide, "Part 1: putting in a Windows 2000 Server as
a site Controller"
http://www.microsoft.com/windows2000/techinfo/planning/server/serversteps.asp. If you're not
victimization the common infrastructure, you wish to create the suitable changes to the current
instruction set.
Although not needed, we tend to conjointly suggest reading and playing the exercises on the
market within the gradual Guide to Understanding the cluster Policy Feature Set. It addresses
however cluster Policy works and might be applied within the context of remote installations.
Prerequisites for consumer Installations
Ensure that the consumer computer's network card has been set because the primary boot
device inside the system BIOS. once the consumer pc boots and is designed with the network
card because the primary boot device, it requests a network service boot from the remote
installation server on the network. Once contacted, the RIS server prompts users to press the F12
key to transfer the consumer Installation wizard. Users ought to be schooled to press F12 given
that prompted, and given that they have a replacement OS installation or access to maintenance
and troubleshooting tools. Once the OS has been put in via RIS, the user will ignore the request
to press F12 throughout future consumer pc reboots. If victimization the RIS boot disk, merely
insert the boot floppy into the drive and begin the consumer pc. the pc boots from the disk, and
also the user is requested to press F12 to initiate the network service boot. once the RIS boot disk
is employed, the user should take away the boot floppy at some extra point pressing F12 and
before the text mode portion of setup completes.
Note: Compaq pc systems offer the flexibility to press the F12 key throughout power abreast of
PC98 or web PC-based systems. during this case, the user is needed to press F12 on the Compaq
Splash screen, so press F12 once more once prompted by the RIS server.
Top of page
Installing the Windows 2000 Remote Installation Services
The following directions assist you install, configure, and use the Windows 2000 Remote
Installation Services.
Solution
remote operating system installation
Remote Installation Services (RIS) ships as a part of the Windows® 2000 Server software
system. This document outlines the steps necessary to put in, configure, and use RIS.
RIS was designed to cut back the prices incurred by pre-installing or physically visiting every
consumer pc to put in the software system (OS). By combining RIS with alternative Windows

3. 2000 IntelliMirror™ management technologies features—User knowledge Management,
software package Installation and Maintenance, and User Settings Management—companies get
pleasure from higher disaster recovery with easier OS and application management.
Prerequisites
See Appendix A below to confirm that each your server and consumer hardware meet the
remote installation hardware necessities.
The drive on the server wherever you decide on to put in RIS should be formatted with the
NTFS filing system. RIS needs a big quantity of space and can't be put in on constant drive or
partition on that Windows 2000 Server is put in. make sure that the chosen drive contains enough
free space for a minimum of one full Windows 2000 skilled compact disc—a minimum of
roughly 800 megabytes (MB)–1 GB (GB).
RIS needs many alternative services that conjointly ship as a part of Windows 2000 Server.
These services will be put in on individual servers, or all on one server, counting on your
network design:
Domain Name Service (DNS) Server. Remote installation depends on DNS for locating the
directory service and consumer machine accounts. you'll use any Windows 2000 Active
DirectoryTM service-compliant DNS server, otherwise you will use the DNS server given
Windows 2000 Server.
Dynamic Host Configuration Protocol (DHCP) Server. RIS needs a DHCP server to be gift and
active on the network. The remote boot-enabled consumer computers receive AN information
processing address from the DHCP server before contacting RIS.
Active Directory. RIS depends on Windows 2000 Active Directory for locating existing
consumer machines further as existing RIS servers. RIS should be put in on a Windows 2000-
based server that has access to Active Directory. this will be a site controller or a server that's a
member of a site with access to the Active Directory.
To ensure a in installation, you want to install and tack together the extra services delineate
higher than so as for RIS to perform. additionally, certify that you just have each the Windows
2000 Server and skilled CDs on the market.
Before starting this gradual guide, you wish to create the common infrastructure, that specifies a
specific hardware and software package configuration. The common infrastructure is roofed
within the Common Infrastructure gradual guide, "Part 1: putting in a Windows 2000 Server as
a site Controller"
http://www.microsoft.com/windows2000/techinfo/planning/server/serversteps.asp. If you're not
victimization the common infrastructure, you wish to create the suitable changes to the current
instruction set.
Although not needed, we tend to conjointly suggest reading and playing the exercises on the

4. market within the gradual Guide to Understanding the cluster Policy Feature Set. It addresses
however cluster Policy works and might be applied within the context of remote installations.
Prerequisites for consumer Installations
Ensure that the consumer computer's network card has been set because the primary boot
device inside the system BIOS. once the consumer pc boots and is designed with the network
card because the primary boot device, it requests a network service boot from the remote
installation server on the network. Once contacted, the RIS server prompts users to press the F12
key to transfer the consumer Installation wizard. Users ought to be schooled to press F12 given
that prompted, and given that they have a replacement OS installation or access to maintenance
and troubleshooting tools. Once the OS has been put in via RIS, the user will ignore the request
to press F12 throughout future consumer pc reboots. If victimization the RIS boot disk, merely
insert the boot floppy into the drive and begin the consumer pc. the pc boots from the disk, and
also the user is requested to press F12 to initiate the network service boot. once the RIS boot disk
is employed, the user should take away the boot floppy at some extra point pressing F12 and
before the text mode portion of setup completes.
Note: Compaq pc systems offer the flexibility to press the F12 key throughout power abreast of
PC98 or web PC-based systems. during this case, the user is needed to press F12 on the Compaq
Splash screen, so press F12 once more once prompted by the RIS server.
Top of page
Installing the Windows 2000 Remote Installation Services
The following directions assist you install, configure, and use the Windows 2000 Remote
Installation Services.