1. MAYUR R SAVALE
OBJECTIVE:-
To work as a dynamic professional in an environment that would provide opportunity to utilize
my skills and strength. Where I would like to contribute my educational knowledge for both personal
and professional growth.
EXPERIENCE:-
(1) Abhilasha Tex-Chem pvt. ltd., Tarapur. (Aarti group)
Role: Production Engineer
Duration: From 20 Aug 2013 to till date.
Job profile:
 Production management
 Quality control
 Safety in charge
 Maintenance scheduling, maintain record of maintenance done on equipment in plant
 Work on SOP for all operations in plant
 SCADA system installation
Achievements:
 Make changes to control the HCl fumes emission, firstly caustic solution is circulating to
neutralize the fume. Instead of caustic solution I replace it by water. This benefit us to stop
caustic handling, cost reduced, acidic water produced recycle to the ETP.
 Used recycle water for the pusher centrifuge to minimize fresh water consumption partly
solve the excess effluent generation.
For the quality of product
 Change in process For improve the product quality slow down the recovery which help to
improve quality, crystal size improve, drying time minimize due to less moisture content
and also less pressure build up in scrubber.
Final year engineering project
1) Installed in ETP plant
2) Successfully trial run of 6KL batch complete
3) Results are as desired CaCl2 concentration drop from 19.75 to 7.8%. Now working to
decrease concentration below 1% in influent.
4) Scale up of system to treat 40KL per Day in progress.
Recently working on:
1) Upgradation of above system to reduce CaCl2 to1%
2) Used flash steam from plant condensate to melt PNCB to melt which used in process. Flash
steam replaces boiler steam which minimize on boiler to supply of steam.
3) Project of ETP modification capital investment of about 50lac.

2. EDUCATIONAL DETAILS:-
B.E. Chemical 2012-2013 75.06%
Finolex Academy of Management & Technology, Ratnagiri.Mumbai
FINAL YEAR PROJECT:-
A final year project on “Cooling Water Treatment by Hydrodynamic Cavitation”
Project Synopsis:
 During the chemical treatment of the water Formation of scale, high pH of the water, problem of
corrosion resulted
 Hydrodynamic cavitation is alternative to the chemical treatment. In this technique water is pass at
the certain flow rate through constriction device due to this pressure is reduced at the upstream
velocity increases and air bubbles are form and at downstream pressure recovered bubbles are
collapse
 During these CaCO3 deposit which nonstick in nature ,not adhere to wall of pipes, vessels
 This technique is efficient and effective then chemical treatment to treat the water
Role: Team Member
 Referred about 25-30 papers related to this topics
 Experimental setups used in that papers is 5 HP capacity motor, but we used 0.5 HP pump
 Design calculation done by me by referring fluid mechanics books and papers
 During the run of project face the problem of air leakage through pipe joints, I FOUND solution that
is conventional method of pipe connection
 Solved the problem of gasket by preparing it from waste tire rubber by cutting it into the size of the
flange and placing in between flange
CURRICULAR ACTIVITIES:-
 Behavior based safety training arranged by aarti industries
 Industrial Training One month at Aarti industries, Anisiden Division, Sarigam, Gujarat.
 Aspen workshop at IIT, Mumbai.
 Pursuing process engineering course with xyntech solution, Included process simulation by
CHEMCAD, UNISIM, HYSIS Software, Sizing of line, equipment etc.
PERSONAL DETAILS:-
Date of Birth:-21/01/1992
Nationality:-Indian
Contact:-+918097544621, +919624187421
E-mail:- mayursavale1992@gmail.com
Residence address : B-202, Nilkamal App.,
Bhilad (w),
Ta.- Umbergaon, Dist-Valsad
Guj-396105