2. History of FinFET
Introduction to FinFET
Short Channel effect
Attributes of the short channel effect
Reasons for evolution of FinFET
FinFET structure
General lay out and modes of operation
Fins
Fabrication of FinFET
Chemical vapour deposition
Electron Beam Lithography
Oxidation
Formation of poly silicon gate
Evaluation of FinFET
Reasons for poor performance
Parasitic capacitance
How to avoid parasitic capacitance
Advantage of FinFET
Disadvantages of FinFET
Latest updates about FinFET
Conclusion
3. ๏จ FINFET is a transistor design first developed
by Chenming Hu and his colleagues at the
University of California at Berkeley, which tries
to overcome the worst types of SCE(Short
Channel Effect).
๏จ Originally, FINFET was developed for use on
Silicon-On-Insulator(SOI).
๏จ SOI FINFET with thick oxide on top of fin are
called โDouble-Gateโ and those with thin oxide
on top as well as on sides are called โTriple-
Gateโ FINFETs
4. ๏จ The term โFINFETโ describes a non-planar,
double gate transistor built on an SOI
substrate, based on the single gate transistor
design.
๏จ The important characteristics of FINFET is that
the conducting channel is wrapped by a thin Si
โfinโ, which forms the body of the device.
๏จ The thickness of the fin determines the effective
channel length of the device.
5. ๏จ It is an effect whereby a MOSFET in which the
channel length is the same order of magnitude
as the depletion layer widths of source & drain
junctions, behaves differently from the other
MOSFETs.
๏จ As the channel length โlโ is reduced to increase
both the operation speed and the number of
components per chip, the so called SCE occurs.
6. 1. Limitation imposed on the electron drift
characteristics in the channel.
2. Modification of threshold voltage (Short
Channel Effect(SCE))
7. ๏จ For the double gate SOI MOSFETs, the gates
control the energy barrier b/w source and
drain effectively.
๏จ Therefore, the Short Channel Effect(SCE) can
be suppressed without increasing the channel
impurity concentration.
10. ๏จ The basic electrical layout and mode of
operation of a FINFET does not differ from a
traditional FET.
๏จ There is one source and one drain contact as
well as a gate to control the current flow.
๏จ In contrast to planar MOSFET, the channel b/w
source and drain is build as 3D bar on top of
the Si substrate and are called fin.
11. CONTINUEDโฆโฆโฆ
The gate electrode is then wrapped around the channel, so
that there can be formed several gate electrodes on each side
which leads to the reduction in the leakage currents and an
enhanced drive current.
12. ๏จ The fin is used to form the raised channel.
๏จ As the channel is very thin the gate has a great
control over carriers within it, but, when the
device is switched on, the shape limits the
current through it to a low level.
๏จ The thickness of the fin (measured in the
direction from source to drain) determines the
effective length of the device.
13. ๏จ The heart of the FINFET is a thin Si fin, which
serves as a body of the MOSFET.
๏จ A heavily doped poly Si film wraps around the
fin and makes the electrical contact to the
vertical faces of the fin.
๏จ A gap is etched through the poly Si film to
separate the source and drain.
The various steps in the fabrication of FINFETs are
discussed as follows.
14. ๏จ SiN and SiO layers are deposited on Si film to
make a hard mask or a cover layer.
๏จ The cover layer will protect the Si fin
throughout the fabrication process.
๏จ Then, a layer of SiO2 is developed by the
process of dry etching.
๏จ The layer of SiO2 is used to relieve the stress.
15. ๏จ The fine Si fin is patterned by EB Lithography
with 100keV acceleration energy.
๏จ The resist pattern is slightly ashed at 5W and
30 sec to reduce the Si fin width.
๏จ Then using top SiO layer as a hard etching
mask, the SiO layer is etched.
๏จ By this process, the silicon fin is patterned.
16. ๏จ A thin layer of sacrificial layer of SiO2 is
grown.
๏จ Then, the sacrificial oxide is stripped
completely to remove etch damage.
๏จ While the cover layer protects the Si fin, the
amorphous Si is completely removed from the
side of the Si fin.
๏จ The amorphous Si is in contact with the Si fin at
its side surfaces becomes the impurity
diffusion source that forms the transistor
source and drain.
17. ๏จ The gate oxidation should thin the Si fin width
slightly.
๏จ By oxidizing the Si surface, gate oxide as thin
as 2.5nm is grown.
๏จ Because the area of Si fin inside the surface is
too small, we use dummy wafers to measure
the oxide thickness.
๏จ Hence the gate oxide is grown.
18. ๏จ The boron doped Si is deposited at 475`C as the
gate material.
๏จ Because the source and drain extension is
already formed and covered by thick SiO layer,
no high temperature steps are required after
the gate deposition.
๏จ The total parasitic resistance due to probing is
about 3000.
20. ๏จ Large bits and holes in the Si fin and the source
drain areas.
๏จ In fabrication, photo resist alone is not a
sufficient task.
21. ๏จ Suppressed Short Channel Effect(SCE)
๏จ Better in driving current
๏จ More compact
๏จ Low cost
22. ๏จ Reduced mobility for electrons
๏จ Higher source and drain resistances
๏จ Poor reliability
23. ๏จ In the New York Times, On may 4 2011, it was
published that INTEL will use FINFET for
about 22nm.
๏จ According to various sources, INTELโs FINFET
shape has an unusual shape of a triangle rather
than rectangle because triangle has a high
structural strength, higher area to volume ratio
thus increasing the switching performance.
24. The following key features are
experimentally verified.
๏จ The self aligned double gate effectively
suppresses Short Channel Effect even in 17nm
gate length.
๏จ Gate is self-aligned, which is raised to reduce
the parasitic capacitance.