The document provides information on the engines and engine systems of the Boeing 737 NG. It describes the dual CFM56-7 turbofan engines in detail, including the N1 and N2 rotors. It also outlines the electronic engine control (EEC), engine fuel and oil systems, and normal and alternate engine instrument displays. Key details covered include the EEC modes, engine instrumentation, fuel shutoff valves, oil temperature and pressure monitoring, and engine fault indications.

1. B 737 NG Ground School.
•B 737 NG Ground School.
See the aircraft study guide at www.theorycentre.com
The information contained here is for training purposes only. It is of a general nature it is
unamended and does not relate to any individual aircraft. The FCOM must be consulted for
up to date information on any particular aircraft.

2. ENGINES

3. Introduction
The airplane is powered by two CFM56–7 engines. The engine is a
dual–rotor, axial–flow turbofan.
The N1 rotor consists of a fan, a low–pressure compressor and a low–
pressure turbine.
The N2 rotor consists of a high–pressure compressor and a high–
pressure turbine.
The N1 and N2 rotors are mechanically independent.
The N2 rotor drives the engine gearboxes. A bleed–air–powered starter
motor is connected to the N2 rotor via the accessory gearbox.

4. Introduction
737-800 is powered by dual rotor CFM56-7 turbofan
engines:
CFM is a joint company of GE Commercial fan
and Snecma Moteurs of France

5. •N1 rotor comprises of a FAN.
• 3 stage booster section
(low pressure compressor)
• 4 stage low pressure turbine
•The low pressure section
produces 80% of Thrust.
•Produced by Snecma

6. Engine General Data.
Fan Diameter 155 cm.
N1 Red line 104% 5,380 RPM
•N1 rotor comprises of a FAN.
• 3 stage booster section
(low pressure compressor)
• 4 stage low pressure turbine
•The low pressure section
produces 80% of Thrust.
•Produced by Snecma

7. •N2 rotor comprises of a 9 stage high
pressure compressor & a single stage
high pressure turbine.
•Based on the GE 101 engine designed
for the B1B bomber.

8. ENGINE GENERAL DATA
N2 RED Line 105% 15,183 RPM
•N2 rotor comprises of a 9 stage high
pressure compressor & a single stage
high pressure turbine.
•Based on the GE 101 engine designed
for the B1B bomber.

9. •N2 rotor drives the engine
accessory gearbox

10. ENGINE GENERAL DATA.
EGT.
RED line 950º C
Engine start limit 725º C

14. AFT OVERHEAD PANEL
FWD OVERHEAD PANEL
ENGINE PANEL

15. Electronic Engine Control (EEC)
Each engine has a full authority digital EEC. Each EEC has two independent
control channels, with automatic channel transfer if the operating channel fails.
With each engine start the EEC alternates between control channels if on the
previous start N2 exceeded 76% RPM
The EEC uses thrust lever inputs to automatically control forward and reverse
thrust. N1 is used by the EEC to set thrust in two control modes: normal and
alternate.
Manual selection of the control mode can be made with the EEC switches on
engine panel.

16. EEC Normal Mode
In the normal mode, the EEC uses sensed flight conditions and bleed air demand to
calculate N1 thrust ratings.
The EEC compares commanded N1 to actual N1 and adjusts fuel flow through the hydro
mechanical unit (HMU) to achieve the commanded N1.

17. EEC Normal Mode
The maximum rated thrust is available at the forward thrust lever stop.The full rated
takeoff thrust for the installed engine is available at a thrust lever position less than the
forward stop. Fixed or assumed temperature derated takeoff thrust ratings are set at
thrust lever positions less than full rated takeoff.
The EEC limits the maximum thrust according to the airplane model.

18. EEC Alternate Mode
The EEC can operate in either of two alternate modes, soft or hard. If required signals
are not available to operate in the normal mode, the EEC automatically changes to the
soft alternate mode. When this occurs, the ALTN switch illuminates and the ON
indication remains visible. In the soft alternate mode, the EEC uses the last valid flight
conditions to define engine parameters which allows the mode change to occur with no
immediate change in engine thrust. Thrust rating shortfalls or exceedances may occur
as flight conditions change. The soft alternate mode remains until the hard alternate
mode is entered
Engine 1 in SOFT ALTN Engine 2 Normal mode.

19. The soft alternate mode remains until the hard alternate mode is entered by either
retarding the thrust lever to idle or manually selecting ALTN with the EEC switch on the
aft overhead panel.
Note: Loss of either DEU results in a loss of signal to both EECs. The EEC ALTN lights
illuminate and each EEC reverts to the alternate mode to prevent the engines from
operating on a single source of data.
When the hard alternate mode is entered, the EEC reverts to the alternate mode thrust
schedule. Hard alternate mode thrust is always equal to or greater than normal mode
thrust for the same lever position. i.e. at idle thrust there will be no difference, at settings
close to maximum there will be approximately 10% thrust difference for any given thrust
lever position. If the hard alternate mode is entered by reducing the thrust lever to idle
while in the soft alternate mode, the ALTN switch remains illuminated and the ON
indication remains visible. When ALTN is selected manually, the ON indication is
blanked.
Both engines in HARD ALTN mode.
Putting both engines into alternate avoids thrust lever stager due
to thrust differences between the two modes.

20. EEC

21. Structural Limit Protection
The EEC provides N1 and N2 redline over speed protection in both normal
and alternate modes.
The EGT limit must be observed by the crew because the
EEC does not provide EGT redline exceedance protection.

22. Idle Operation
The EEC automatically selects ground minimum idle, flight minimum idle, and
approach idle. Ground minimum idle is selected for ground operations and flight
minimum idle is selected for most phases of flight.
Approach idle is selected in flight if flaps are in landing configuration or engine
anti–ice is ON for either engine.
At the same airspeed and altitude, N1 and N2% RPM will be higher for approach
idle than for flight minimum idle. This higher% RPM improves engine acceleration
time in the event of a go–around.
Approach idle is maintained until after touchdown, when ground minimum idle is
selected. In flight, if a fault prevents the EEC from receiving flap or anti–ice signals,
approach idle schedule begins below 15,000 feet MSL.

23. The EEC must receive electrical power to supply engine operating data to the flight
deck engine indications.
The electronic engine control (EEC) alternator usually supplies electrical power to the
EEC. The EEC alternator is the primary electrical power source for the EEC.
When the N2 speed is more than 15 % and alternator power quality is in limits, the
EEC gets power from the EEC alternator.
The on side AC transfer bus supplies electrical power to the EECs when the
alternator can not supply power.
When the EEC is not powered N1 and N2 tachometer information is connected
directly to the DEU’s and will be displayed,
oil quantity and engine vibration are also displayed directly from the engine sensors.
During battery start with no power on the airplane, only N1, N2, and oil quantity
are available. The EEC is not powered until the engine accelerates to a speed
greater than 15% N2. At 15% N2, the EEC becomes energized and pointers/digits
for all engine parameters are displayed.

24. •Engine Indications
•Primary and secondary engine indications are provided. Engine indications are
displayed on the upper display unit (DU),
Primary indications can be moved automatically or manually to the lower DU or
manually to the Captain’s or First Officer’s inboard DU.

25. Primary Engine Indications
N1 and EGT are the primary engine indications. The primary engine indications are normally
displayed on the upper DU. If that unit fails, the display automatically moves to the lower DU.
The primary engine indications can also be manually selected to either the Captain’s or First
Officer’s inboard DU, or the lower DU, using the respective display select panel.

26. N1 RPM Readouts
Reference N1 bugs. (digital)
Show the active N1 limit Displayed (white) – normal
operating range.
Displayed (red) –
• operating limit exceeded
• on ground after engine
shutdown, red box
indicates an inflight
exceedance has occurred.

27. N1 Redlines
Displayed (red) – N1% RPM
operating limit
N1 Command Sectors
Displayed (white) – momentary
difference between actual N1
and value commanded by thrust
lever position.

28. Exhaust Gas Temperature (EGT) Redlines Exhaust Gas Temperature (EGT) Amber Bands
Displayed (amber) – lower end of band displays
Displayed (red) – maximum takeoff EGT limit . maximum continuous EGT limit .

29. Exhaust Gas Temperature (EGT) Start Limit Lines
Displayed (red) – until the engine achieves stabilized
idle (approximately 59% N2).

30. SECONDARY ENGINE INDICATIONS
N2, fuel flow, oil pressure, oil temperature, oil quantity, and engine vibration are the secondary
engine indications. The secondary engine indications, except for fuel flow, are manually selected to
either the Captain’s or First Officer’s inboard DU, or the lower DU, using the respective display
select panel and the ENG switch on the engine display control panel. Fuel flow is displayed full time
on the upper display unit below the primary engine indications.
The secondary engine indications are automatically displayed when:
• the displays initially receive electrical power
• in flight when an engine start lever is moved to CUTOFF
• in flight when an engine N2 RPM is below idle
(flight idle is 72% N2)
• a secondary engine parameter is exceeded.
ENG switch; first push displays second push blanks
When the secondary engine indications are automatically displayed, they cannot be cleared until
the condition is no longer present.

31. SECONDARY ENGINE INDICATIONS
Normally displayed on
the lower display unit but
can be selected to the
inboard DU’s by the pilot
The lower DU is normally kept black in flight. If any engine parameter is exceeded the
entire display shows automatically!

32. Normal Display Format
N1, EGT, and N2 are displayed as both digital readouts and round dial/moving
pointer indications. The digital readouts display numerical values while the
moving pointers indicate relative value.

33. Oil pressure, oil temperature, and engine vibration indications are both digital readouts and
vertical indication/moving pointers.
Fuel flow and oil quantity are digital readouts only. All digital readouts are enclosed by
boxes.
The dials and vertical indications display the normal operating range, caution range, and
operating limits.
Normal operating range is displayed on a dial or vertical indication in white.

34. N1, EGT, and N2 have operating limits indicated by redlines. EGT also displays
an amber caution limit. If one of these indications exceeds the red or amber line,
the digital readout, box, pointer, and indicator change colour to red or amber.

35. The oil temperature and oil pressure vertical indications have a caution range and an
operating limit redline.

36. Low Oil Pressure (OIL PRESS) Amber Band
Displayed (amber) – low oil pressure caution range beginning at red line.:
• variable depending on N2% RPM above 65% N2
• amber band not displayed below 65% N2.

37. If the oil temperature or pressure reaches the caution range, the digital readout, digital
readout box, and pointer all change colour to amber.
If one of these indications reach the operating limit, the digital readout, digital readout box,
and pointer all change colour to red.

38. Oil quantity and vibrations do not have any limits. If Vibration is
above normal levels the digital box changes to revers video
showing a white box with black digits .
Similarly if oil quantity is low the indicator changes to revers video.

39. An engine failure alert indication (ENG FAIL) is displayed in amber on the
EGT indicator when the respective engine is operating at a condition below
sustainable idle (50% N2) and the engine start lever is in the IDLE position.
The alert remains until the engine recovers, the engine start lever is moved
to CUTOFF, or the engine fire warning switch is pulled

40. Compact Display
In compact format, the primary and secondary engine indications are combined on the
same display. The N1 and EGT indications are displayed as they are normally.
All other indications change to digital readouts only. N2, oil temperature, and oil pressure
digital readouts turn red or amber if an exceedance occurs.
Primary and secondary engine indications are displayed in compact format on the upper
DU when the secondary engine indications are selected for display (manually or
automatically) and the lower DU is unavailable. Alternatively, the compacted indications
are displayed on the lower DU if the upper DU is unavailable.

41. T12 sensor For Fan Inlet TAT
RAM AIR INLET
For EEC Cooling.

42. Electronic Engine Control (EEC)
Engine Panel
Non Dispatchable Fault
• Light remains illuminated ONLY WHILE
ENGINE IS RUNNING.
•When engine is shut down the fault is
stored in BITE logic and the light will not
illuminate at next start.
•This light comes on for non dispatchable
faults including the EEC is operating with
a single working channel.
Light is INHIBITED IN FLIGHT. From 80 Knots Until 30 sec after landing
Illuminated on the ground, engine running –
Do NOT dispatch due to system fault

43. Engine Fuel System
Fuel is delivered under pressure from fuel pumps located in the fuel tanks. The fuel flows through
a fuel spar shutoff valve located at the engine mounting wing stations. The fuel passes through the
first stage engine fuel pump where pressure is increased. It then passes through two fuel/oil heat
exchangers where IDG oil and main engine oil heat the fuel. A fuel filter then removes
contaminants.
Fuel automatically bypasses the filter if the filter becomes contaminated. Before the fuel bypass
occurs, the fuel FILTER BYPASS alert illuminates on the fuel control panel. The second stage
engine fuel pump adds more pressure before the fuel reaches the hydro mechanical unit (HMU).
To meet thrust requirements, the EEC meters fuel through the HMU.
The spar fuel shutoff valve and engine fuel shutoff valve allow fuel flow to the engine when both
valves are open. The valves are open when the engine fire warning switch is in and the start lever
is in IDLE. Both valves close when either the start lever is in CUTOFF or the engine fire warning
switch is out. SPAR VALVE CLOSED and ENG VALVE CLOSED lights located on the overhead
panel indicate valve position.
Fuel flow is measured after passing through the engine fuel shutoff valve and is displayed on the
display unit. Fuel flow information is also provided to the FMS.

44. Fuel control levers. No1 cutoff No2 idle.
Fire switches must be down to open spar and engine fuel
shutoff valves.

46. Engine Oil System
Oil from the individual engine tank is circulated under pressure, through the engine
to lubricate the engine bearings and accessory gearbox. The oil quantity indicator,
oil temperature indicator, oil pressure indicator and LOW OIL PRESSURE alert are
all located on the display unit.
The oil system is pressurized by the engine driven oil pump. Oil from the pump,
goes to the engine bearings and gearbox. Sensors for the oil temperature indicator,
oil pressure indicator and LOW OIL PRESSURE alert are located downstream of
the oil pump prior to engine lubrication.
Oil is returned to the oil tank by engine driven scavenge pumps. From the
scavenge pumps oil passes through a scavenge filter. If the filter becomes
saturated with contaminants, oil automatically bypasses the filter. Prior to the oil
bypassing the scavenge filter, the OIL FILTER BYPASS alert illuminates on the
upper display unit.
Prior to returning to the oil tank, the oil passes through the main engine oil cooler
where it is cooled by engine fuel to maintain proper oil temperature.

47. After 10 seconds
LOW OIL PRESSURE Alert Illuminated (amber) –
• steady – oil pressure at or below red line
• blinking – with a condition of low oil pressure. Alert is displayed and solid amber boxes
are displayed in unannunciated positions for that engine.
All three boxes blink for ten seconds, then alert remains on steady and solid amber boxes
are removed
Note: Blinking is inhibited:
• during takeoff from 80 knots to 400 feet RA, or 30 seconds after reaching 80 knots,
whichever occurs first
• during landing below 200 feet RA until 30 seconds after touchdown
• during periods when blinking is inhibited, alerts illuminate steady.

48. OIL FILTER BYPASS Alert Illuminated (amber) –
• steady – indicates an impending bypass of scavenge oil filter
• blinking – with an impending bypass. Alert is displayed and solid amber boxes are
displayed in unannunciated positions for that engine. All three boxes blink for ten
seconds, then alert remains on steady and solid amber boxes are removed
Note: Blinking is inhibited:
• during takeoff from 80 knots to 400 feet RA,
or 30 seconds after reaching 80 knots,
whichever occurs first
• during landing below 200 feet RA until 30
seconds after touchdown
• during periods when blinking is inhibited,
alerts illuminate steady.

50. Engine Start System
Starter operation requires pressurized air and electrical power. Air from the bleed air
system powers the starter motor. The APU, an external ground cart, or the other operating
engine provides the bleed air source. The minimum duct pressure required for a cross
bleed start is 30 PSI.
In the GRD position, the engine start switch uses battery power to close the engine bleed
air valve and open the start valve to allow pressure to rotate the starter. When the start
valve opens, an amber START VALVE OPEN alert is provided on the upper display unit.
The starter rotates the N2 compressor through the accessory drive gear system. When the
engine accelerates to the recommended value (25% N2 or max motoring), moving the
engine start lever to the IDLE position opens the fuel valves on the wing spar and engine,
and causes the EEC to supply fuel and ignition to the combustor where the fuel ignites.
Initial fuel flow indications lag actual fuel flow by approximately two seconds, therefore,
during engine start, an EGT rise may occur before fuel flow indication.
At starter cutout speed (approximately 56% N2), the EEC removes power from the start
switch holding solenoid. The engine start switch returns to OFF, the engine bleed air valve
returns to the selected position, and the start valve closes.

51. •STARTING PROCEDURE.
The Captain calls the start
sequence Normally Number 2 first
on the 737. The F/O selects Ground

53. GRD commands the starter
control valve to open and
arms the ignition.
The starter turns the gearbox.
The gearbox turns the HP
compressor N2.

54. When The engines is at Maximum motoring the captain moves the
FUEL CONTROL lever to IDLE

55. The B737 Engine has 2 fuel valves.
ENGINE FUEL SHUTOFF VALVE
SPAR VALVE

56. When the captain moves the Fuel Control
Lever to Idle Both fuel valves OPEN.
The ignition is turned on and fuel flows
into the combustion chamber.

57. Abnormal Start Protection (Ground Starts Only)
During ground starts, the EEC monitors engine parameters to detect impending hot starts,
engine stalls, EGT start limit exceedances, and wet starts. These protection features do not
function during inflight starts.
If an impending hot start is detected by a rapid rise in EGT or EGT approaching the start
limit, or a compressor stall occurs, the white box surrounding the EGT digital readout
flashes white. The flashing white box resets when the start lever is moved to CUTOFF or
the engine reaches idle N2. Current versions of EEC software (7.B.Q and later)
automatically turn off the ignition and shuts off fuel to the engine for an impending hot start
or stall.
If the EGT exceeds the starting limit, the EGT display, both box and dial, turn red. The EEC
automatically turns off the ignition and shuts off fuel to the engine. The alert terminates and
the display returns to white when EGT drops below the start limit. Following shutdown of
both engines, the EGT box turns red to remind the crew of the exceedance.
A wet start occurs if the EGT does not rise after the start lever is moved to IDLE. If a wet
start is detected, the EEC turns off the ignition and shuts off fuel to the engine 15 seconds
after the start lever is moved to IDLE.

58. Engine Ignition System
Each engine has two igniter plugs. The EEC arms the igniter plug(s) selected by
the ignition select switch. The left igniter plug receives power from the associated
AC transfer bus. The right igniter plug receives power from the AC standby bus.
Auto-Relight
An auto-relight capability is provided for flameout protection. Whenever the EEC
detects an engine flameout, both igniters are activated. A flameout is detected
when an uncommanded rapid decrease in N2 occurs, or N2 is below idle RPM.

59. Ignition RIGHT IGNITER
AC STANDBY BUS
EEC
High Energy Ignition unit (HEIU)
TRANSFER BUS
LEFT IGNITER

60. Ignition
Ground start uses only the selected igniter. Right is normally used for the first start of each day
to check the standby system ignition.

61. Ignition

62. Ignition

63. Ignition
Selecting FLT start uses both igniters regardless of the switch position.

64. Inflight Starting
Two methods of starting an engine inflight are available, windmill and crossbleed.
None of the ground start protection features are functional during inflight start.
Note: At low N2 values, the oil scavenge pump may not provide enough pressure to
return oil to the tank, causing a low oil quantity indication. Normal oil quantity should be
indicated after start.
If crossbleed starting is required, the X–BLD indication (XB for the compact engine
display) is displayed above the N2 dial. This indication is based on airplane altitude,
airspeed and N2 RPM.

66. START VALVE OPEN Alert
Illuminated (amber) –
• steady – respective engine start valve open and air is supplied to starter
• blinking – uncommanded opening of start valve. Alert is displayed and solid
amber boxes are displayed in unannunciated positions for that engine. All three
boxes blink for ten seconds, then alert remains on steady and solid amber boxes
are removed
Note: Blinking is inhibited:
• during takeoff from 80 knots to 400
feet RA, or 30 seconds after reaching
80 knots, whichever occurs first
• during landing below 200 feet RA
until 30 seconds after touchdown
• during periods when blinking is
inhibited, alerts illuminate steady.

67. Thrust Reverser
Each engine is equipped with a hydraulically operated thrust reverser, consisting of left
and right translating sleeves. Aft movement of the reverser sleeves causes blocker
doors to deflect fan discharge air forward, through fixed cascade vanes, producing
reverse thrust. The thrust reverser is for ground operations only and is used after
touchdown to slow the airplane, reducing stopping distance and brake wear.

68. Hydraulic pressure for the operation of engine No. 1 and engine No. 2 thrust reversers
comes from hydraulic systems A and B, respectively. If hydraulic system A and/or B fails,
alternate operation for the affected thrust reverser is available through the standby
hydraulic system. When the standby system is used, the affected thrust reverser deploys
and retracts at a slower rate and some thrust asymmetry can be anticipated.
Thrust reverse Normal Stow position.

69. When reverse thrust is selected, an electro–mechanical lock releases, the isolation
valve opens and the thrust reverser control valve moves to the deploy position,
allowing hydraulic pressure to unlock and deploy the reverser system.
An interlock mechanism restricts movement of the reverse thrust lever until the
reverser sleeves have approached the deployed position.
Thrust Reverse Deployed.

70. When either reverser sleeve moves from the stowed position, the amber REV
indication, located on the upper display unit, illuminates. As the thrust reverser
reaches the deployed position, the REV indication illuminates green and the reverse
thrust lever can be raised to detent No. 2. This position provides adequate reverse
thrust for normal operations.
When necessary, the reverse thrust lever can be pulled beyond detent No. 2,
providing maximum reverse thrust.

71. The thrust reverser can be deployed when either radio altimeter senses less
than 10 feet altitude, or when the air/ground sensor is in the ground mode.
Movement of the reverse thrust levers is mechanically restricted until the
forward thrust levers are in the idle position.

72. Downward motion of the reverse thrust lever past detent No. 1 (reverse idle thrust)
initiates the command to stow the reverser. When the lever reaches the full down
position, the control valve moves to the stow position allowing hydraulic pressure
to stow and lock the reverser sleeves. After the thrust reverser is stowed, the
isolation valve closes and the electro–mechanical lock engages.
Thrust reverse Stow or Auto Re-Stow command.

73. When the reverser sleeves are in the stow position, an electro–mechanical lock and
a hydraulically operated locking actuator inhibit motion to each reverser sleeve until
reverser extension is selected.
Additionally, an auto–restow circuit compares the actual reverser sleeve position
and the commanded reverser position. In the event of incomplete stowage or
uncommanded movement of the reverser sleeves toward the deployed position, the
auto–restow circuit opens the isolation valve and commands the control valve to the
stow position directing hydraulic pressure to stow the reverser sleeves. Once the
auto–restow circuit is activated, the isolation valve remains open and the control
valve is held in the stowed position until the thrust reverser is commanded to deploy
or until corrective maintenance action is taken.

74. The REVERSER light, located on the aft overhead panel, illuminates when the thrust
reverser is commanded to stow and extinguishes 10 seconds later when the
isolation valve closes. Any time the REVERSER light illuminates for more than
approximately 12 seconds, a malfunction has occurred and the MASTER CAUTION
and ENG system annunciator lights illuminate.
Engine Panel

75. REVERSER Lights
Illuminated (amber) – one or more of following has occurred:
• isolation valve or thrust reverser control valve is not in commanded Position
• one or more thrust reverser sleeves are not in commanded state
• auto–restow circuit has been activated
• a failure has been detected in synchronization shaft lock circuitry.
Engine Panel

76. ENGINE LIMITATIONS AND RESTRICTIONS.
Engine Limit Display Markings
Maximum and minimum limits are red. Caution limits are amber.
Engine Ignition
Engine ignition must be on for:
• takeoff
• landing
• operation in heavy rain
• anti-ice operation.
Starter duty cycle:
• Do not exceed 2 minutes during each start attempt
• A minimum of 10 seconds is needed between start attempts
(Oil is thrown out of the gears by centrifugal force during start. The 10
seconds allows for re-oiling of the gears.)

77. ENGINE LIMITATIONS AND RESTRICTIONS.
Do the ABORTED ENGINE START checklist for one or more of the following abort start
conditions:
• the N1 or N2 does not increase or increases very slowly after the EGT increases
• there is no oil pressure indication by the time that the engine is stable at idle
• the EGT does not increase by 10 seconds after the engine start lever is moved to IDLE
• the EGT quickly nears or exceeds the start limit
Do not re–engage the ENGINE START switch until engine RPM is below 20% N2.
Engine starter and or gearbox damage may be caused if RPM is above 20% when
the starter is engaged.
Engine High oil temperature.
If the oil temperature is in the red band do the engine failure or shutdown checklist.
If temperature is in the amber band for more than 45 minutes do the engine failure or
shutdown checklist.

78. What protection is supplied with EEC’s in soft or hard alternate mode ?

79. What protection is supplied with EEC’s in soft or hard alternate mode ?
•Structural Limit Protection
The EEC provides N1 and N2 redline overspeed protection in both normal
and alternate modes.
The EGT limit must be observed by the crew because the EEC does not
provide EGT redline exceedance protection.

80. The amber REVERSER light will illuminate under what conditions?

81. The Amber REVERSER light will illuminate under what conditions?
Isolation valve or thrust reverser control valve not in commanded position
Thrust reverser sleeve position sensors are in disagreement
Auto-re-stow circuit has been activated
A failure has been detected in synchronisation shaft lock circuitry

82. What is required before thrust reversers can be deployed?

83. What is required before thrust reversers can be deployed?
Forward thrust levers idle, (Mechanical lock)
AND either RA<10 feet OR ground mode

84. •ENGINES
For how long can an engine be operated with the oil
temperature indication coloured amber?

85. •ENGINES
For how long can an engine be operated with the oil
temperature indication coloured amber?

86. The maximum continuous EGT is indicated by:

87. The maximum continuous EGT is indicated by:

88. During Takeoff, How is the low oil pressure alert displayed?

89. During Takeoff, How is the low oil pressure alert displayed?
ALL BOXES FLASH
FOR 10 SECONDS
FLASHING IS INHIBITED
DURING TAKEOFF.
Note: Blinking is inhibited:
• during takeoff from 80 knots to 400 feet RA, or 30 seconds after
reaching 80 knots, whichever occurs first
• during landing below 200 feet RA until 30 seconds after touchdown
• during periods when blinking is inhibited, alerts illuminate steady.

90. The engine oil pressure amber band displays when?

91. The engine oil pressure amber band displays when?
Amber band is only displayed above 65%
N2 and is variable depending on N2 RPM.

92. The engine fuel system is heated by what?

93. The engine fuel system is heated by what?
The IDG fuel cooled oil cooler.
The main engine fuel cooled oil cooler.

94. The engine starter cut out should occur at:

95. The engine starter cut out should occur at:
At starter cutout speed (approximately 56% N2), the EEC removes
power from the start switch holding solenoid. The engine start switch
returns to OFF, the engine bleed air valve returns to the selected
position, and the start valve closes.

96. The engine EEC is operating in the soft alternate mode, this is
indicated by what?

97. EEC Alternate Mode
The EEC can operate in either of two alternate modes, soft or hard. If required signals
are not available to operate in the normal mode, the EEC automatically changes to the
soft alternate mode. When this occurs, the ALTN switch illuminates and the ON
indication remains visible. In the soft alternate mode, the EEC uses the last valid flight
conditions to define engine parameters which allows the mode change to occur with no
immediate change in engine thrust. Thrust rating shortfalls or exceedances may occur
as flight conditions change. The soft alternate mode remains until the hard alternate
mode is entered
Engine 1 in SOFT ALTN Engine 2 Normal mode.

98. The EEC automatically selects approach idle in flight when?

99. Idle Operation
The EEC automatically selects ground minimum idle, flight minimum idle, and
approach idle. Ground minimum idle is selected for ground operations and flight
minimum idle is selected for most phases of flight.
Approach idle is selected in flight if flaps are in landing configuration or engine
anti–ice is ON for either engine.
At the same airspeed and altitude, N1 and N2% RPM will be higher for approach
idle than for flight minimum idle. This higher% RPM improves engine acceleration
time in the event of a go–around.
Approach idle is maintained until after touchdown, when ground minimum idle is
selected. In flight, if a fault prevents the EEC from receiving flap or anti–ice signals,
approach idle schedule begins below 15,000 feet MSL.

100. For a cross bleed start the minimum duct pressure required is?

101. For a cross bleed start the minimum duct pressure required is?
Supplementary Procedure.
•Supplementary
Procedure 7.5

102. What is the maximum RPM for starter motor engagement?

103. What is the maximum RPM for starter motor engagement?

104. What is the maximum starter motor duty cycle?

105. What is the maximum starter motor duty cycle?

106. The right igniter is powered from which Bus ?

107. The right igniter is powered from which Bus ?
Engine Ignition System
Each engine has two igniter plugs. The EEC arms the igniter plug(s) selected by
the ignition select switch. The left igniter plug receives power from the associated
AC transfer bus.
The right igniter plug receives power from the AC standby bus.

108. The END of ENGINES.
•The END of AUTO FLIGHT Part 1
Now take the test at www.theorycentre.com
For more information info@theorycentre.com