This document provides an overview of satellite remote sensing and GIS applications in agricultural meteorology. It discusses how the World Meteorological Organization's Commission for Agricultural Meteorology has promoted the use of remote sensing and GIS since the 1970s. It describes how GIS allows agricultural planners to integrate spatial data layers like soils, climate, and land use to model natural systems and support decision making. The document gives an example of how Italy uses GIS to create wildfire risk maps by combining satellite imagery with territorial data.
This document provides an overview of remote sensing and geographic information systems (GIS) in agriculture. It discusses the history and processes of remote sensing and GIS. Remote sensing involves collecting data from aircraft or satellites using sensors, while GIS involves capturing, storing, analyzing and displaying spatially referenced data on a map. The document outlines various applications of remote sensing and GIS in agriculture such as crop monitoring and yield estimation. It also presents case studies on using these technologies for agro-advisory services, locust monitoring, and land suitability analysis for crops. In conclusion, remote sensing and GIS are useful tools for solving agricultural problems by identifying issues like pests and diseases and enabling change detection over time.
This document is a summer project training report submitted by Md. Fazlul Wahid to the Amity Institute of Geoinformatics and Remote Sensing to fulfill requirements for an MSc in Geoinformatics & Remote Sensing. The report was conducted under the guidance of Dr. Pebam Rocky at the North Eastern Space Applications Centre and focuses on remote sensing and GIS applications in forest monitoring. It provides an acknowledgments section and index before exploring applications such as forest cover change analysis and loss of forest cover due to shifting cultivation over 5-18 pages.
Use of remote sensing for generation of agricultural statisticsjagannatharao
This document discusses the use of remote sensing for generating agricultural statistics. It provides background on how remote sensing has been used globally and in India to estimate crop acreage, crop yields, and develop crop yield models. Some key applications of remote sensing mentioned are using satellite imagery to estimate wheat and rice acreages in India, developing post-stratified estimators of crop yields using vegetation indices, and relating spectral reflectance data to crop growth parameters to forecast crop production. The document outlines the history and progress of applying remote sensing for agricultural statistics in India over the past few decades.
REMOTE SENSING AND GEOGRAPHIC INFORMATION SYSTEMS AM Publications
Remote sensing technology's increasing accessibility helps us observe research and learn about our globe in ways we could only imagine a generation ago. Guides to profound knowledge of historical, conceptual and practical uses of remote sensing which is increasing GIS technology. This paper will go briefly through remote sensing benefits, history, technology and the GIS and remote sensing integration and their applications. Remote sensing (RS) is used in mapping the predicted and actual species and dominates the ecosystem canopy.
Land Use/Land Cover Mapping Of Allahabad City by Using Remote Sensing & GIS IJMER
The present study was carried out to produce and evaluate the land use/land cover maps by on
screen visual interpretation. The studies of land cover of Allahabad city (study area) consist of 87517.47 ha
out of which 5500.35 ha is build up land (Urban / Rural) Area. In this respect, the Build up land (Urban /
Rural) area scorers 6.28% of the total area. It has also been found that about 17155.001ha (19.60 %) of
area is covered by current fallow land. The double/triple crop land of 30178.44ha (34.84%). The area
covered by gullied / ravines is 1539.20 ha (1.75 %) and that of the kharif crop land is 2828.00 ha (3.23 %).
The area covered by other wasteland is 2551.05ha (2.91%). Table 4.1 shows the area distribution of the
various land use and land cover of Allahabad city.
Slide presentations developed to demonstrate how Information and Communication Technologies (ICTs) be used to address climate change, and why ICTs are a crucial part of the solution – i.e. in promoting efficiency, Green Growth & sustainable development, in dealing with climate change and for climate and environmental action. These slide presentations were delivered in February 2011 in Seongnam, near Seoul in Korea.
These presentations were developed and delivered over 2.5 days on the occasion of a Regional Training of Trainers Workshop for upcoming Academy modules on ICT for Disaster Risk Management and Climate Change Abatement. These modules were developed as part of the Academy of ICT Essentials for Government leaders developed by the United Nations (UN) Asia Pacific Centre for ICT Training (APCICT), based in Songdo City, in the Republic of South Korea.
These presentations were developed in 2011, and are somewhat out of date, but most of the principles still apply. Module 10, which has been published, does not include much of the information outlined in these presentations, which are fairly technical. They were developed to address a significant gap in understanding of the technical basis of using ICTs for climate action and because there is a clear bias in development circles against the importance of dealing with climate change mitigation in developing countries. These presentations are an attempt to redress this lack and are published here with this purpose in mind.
The author, Richard Labelle, is presently working on updating these presentations to further highlight the importance of addressing climate change and the important role that technology including ICTs, play in this effort.
This document provides an overview of using remote sensing and GIS in the petroleum industry. It discusses remote sensing concepts and techniques like platforms, cameras, and scanners used to collect geospatial data. It then discusses GIS and how spatial features are stored and layered with attributes for mapping and analysis. As an example, it focuses on applying these tools to study oil formation, exploration, production, and pollution in the UAE. The document aims to explain how remote sensing and GIS can help operations across the petroleum industry life cycle from exploration to environmental monitoring.
Remote sensing provides information about objects on Earth through reflected or emitted radiation captured from a distance. In India, remote sensing is used extensively for agriculture and resource management. The document outlines the various applications of remote sensing in agriculture, including crop production forecasting, crop damage assessment, soil mapping, and drought monitoring. It also describes India's remote sensing program developed by ISRO to design, build, and launch satellites, and the various centers established for remote sensing education and applications.
This document provides an overview of remote sensing and geographic information systems (GIS) in agriculture. It discusses the history and processes of remote sensing and GIS. Remote sensing involves collecting data from aircraft or satellites using sensors, while GIS involves capturing, storing, analyzing and displaying spatially referenced data on a map. The document outlines various applications of remote sensing and GIS in agriculture such as crop monitoring and yield estimation. It also presents case studies on using these technologies for agro-advisory services, locust monitoring, and land suitability analysis for crops. In conclusion, remote sensing and GIS are useful tools for solving agricultural problems by identifying issues like pests and diseases and enabling change detection over time.
This document is a summer project training report submitted by Md. Fazlul Wahid to the Amity Institute of Geoinformatics and Remote Sensing to fulfill requirements for an MSc in Geoinformatics & Remote Sensing. The report was conducted under the guidance of Dr. Pebam Rocky at the North Eastern Space Applications Centre and focuses on remote sensing and GIS applications in forest monitoring. It provides an acknowledgments section and index before exploring applications such as forest cover change analysis and loss of forest cover due to shifting cultivation over 5-18 pages.
Use of remote sensing for generation of agricultural statisticsjagannatharao
This document discusses the use of remote sensing for generating agricultural statistics. It provides background on how remote sensing has been used globally and in India to estimate crop acreage, crop yields, and develop crop yield models. Some key applications of remote sensing mentioned are using satellite imagery to estimate wheat and rice acreages in India, developing post-stratified estimators of crop yields using vegetation indices, and relating spectral reflectance data to crop growth parameters to forecast crop production. The document outlines the history and progress of applying remote sensing for agricultural statistics in India over the past few decades.
REMOTE SENSING AND GEOGRAPHIC INFORMATION SYSTEMS AM Publications
Remote sensing technology's increasing accessibility helps us observe research and learn about our globe in ways we could only imagine a generation ago. Guides to profound knowledge of historical, conceptual and practical uses of remote sensing which is increasing GIS technology. This paper will go briefly through remote sensing benefits, history, technology and the GIS and remote sensing integration and their applications. Remote sensing (RS) is used in mapping the predicted and actual species and dominates the ecosystem canopy.
Land Use/Land Cover Mapping Of Allahabad City by Using Remote Sensing & GIS IJMER
The present study was carried out to produce and evaluate the land use/land cover maps by on
screen visual interpretation. The studies of land cover of Allahabad city (study area) consist of 87517.47 ha
out of which 5500.35 ha is build up land (Urban / Rural) Area. In this respect, the Build up land (Urban /
Rural) area scorers 6.28% of the total area. It has also been found that about 17155.001ha (19.60 %) of
area is covered by current fallow land. The double/triple crop land of 30178.44ha (34.84%). The area
covered by gullied / ravines is 1539.20 ha (1.75 %) and that of the kharif crop land is 2828.00 ha (3.23 %).
The area covered by other wasteland is 2551.05ha (2.91%). Table 4.1 shows the area distribution of the
various land use and land cover of Allahabad city.
Slide presentations developed to demonstrate how Information and Communication Technologies (ICTs) be used to address climate change, and why ICTs are a crucial part of the solution – i.e. in promoting efficiency, Green Growth & sustainable development, in dealing with climate change and for climate and environmental action. These slide presentations were delivered in February 2011 in Seongnam, near Seoul in Korea.
These presentations were developed and delivered over 2.5 days on the occasion of a Regional Training of Trainers Workshop for upcoming Academy modules on ICT for Disaster Risk Management and Climate Change Abatement. These modules were developed as part of the Academy of ICT Essentials for Government leaders developed by the United Nations (UN) Asia Pacific Centre for ICT Training (APCICT), based in Songdo City, in the Republic of South Korea.
These presentations were developed in 2011, and are somewhat out of date, but most of the principles still apply. Module 10, which has been published, does not include much of the information outlined in these presentations, which are fairly technical. They were developed to address a significant gap in understanding of the technical basis of using ICTs for climate action and because there is a clear bias in development circles against the importance of dealing with climate change mitigation in developing countries. These presentations are an attempt to redress this lack and are published here with this purpose in mind.
The author, Richard Labelle, is presently working on updating these presentations to further highlight the importance of addressing climate change and the important role that technology including ICTs, play in this effort.
This document provides an overview of using remote sensing and GIS in the petroleum industry. It discusses remote sensing concepts and techniques like platforms, cameras, and scanners used to collect geospatial data. It then discusses GIS and how spatial features are stored and layered with attributes for mapping and analysis. As an example, it focuses on applying these tools to study oil formation, exploration, production, and pollution in the UAE. The document aims to explain how remote sensing and GIS can help operations across the petroleum industry life cycle from exploration to environmental monitoring.
Remote sensing provides information about objects on Earth through reflected or emitted radiation captured from a distance. In India, remote sensing is used extensively for agriculture and resource management. The document outlines the various applications of remote sensing in agriculture, including crop production forecasting, crop damage assessment, soil mapping, and drought monitoring. It also describes India's remote sensing program developed by ISRO to design, build, and launch satellites, and the various centers established for remote sensing education and applications.
DOCTORAL SEMINAR on remote sensing in AgricultureAmanDohre
This document summarizes a doctoral seminar on recent advances in applying remote sensing to fruit crop production. It discusses the historical development of remote sensing, key principles and stages in remote sensing systems, different platforms (ground, airborne, spaceborne) and sensors used. Applications of remote sensing in fruit crops include estimating crop areas, identifying diseases/pests, assessing water stress, and recommending fertilizer doses. The document also outlines various remote sensing organizations and provides an example of research on using drones to map mango yields based on tree structure.
Identification Of Ground Water Potential Zones In Tamil Nadu By Remote Sensin...IJERA Editor
A case study was conducted to find out the groundwater potential zones in Salem, Erode and Namakkal districts, Tamil Nadu, India with an aerial extent of 360.60 km2. The thematic maps such as geology, geomorphology, soil hydrological group, land use / land cover and drainage map were prepared for the study area. The Digital Elevation Model (DEM) has been generated from the 10 m interval contour lines (which is derived from SOI, Toposheet 1:25000 scale) and obtained the slope (%) of the study area. The groundwater potential zones were obtained by overlaying all the thematic maps in terms of weighted overlay methods using the spatial analysis tool in Arc GIS 9.3. During weighted overlay analysis, the ranking has been given for each individual parameter of each thematic map and weights were assigned according to the influence such as soil −25%, geomorphology − 25%, land use/land cover −25%, slope − 15%, lineament − 5% and drainage / streams − 5% and find out the potential zones in terms of good, moderate and poor zones with the area of 49.70 km2, 261.61 km2 and 46.04 km2 respectively. The potential zone wise study area was overlaid with village boundary map and the village wise groundwater potential zones with three categories such as good, moderate and poor zones were obtained. This GIS based output result was validated by conducting field survey by randomly selecting wells in different villages using GPS instruments. The coordinates of each well location were obtained by GPS and plotted in the GIS platform and it was clearly shown that the well coordinates were exactly seated with the classified zones.
Delineation of irrigation infrastructural, potential and land useIAEME Publication
This study assessed irrigation infrastructure in Muzaffarnagar district, India using satellite imagery. The main canals are Tikri Branch, Nirpura Branch, and Kurthal Branch, with several minor canals branching off. Satellite imagery was used to measure canal lengths and compare to official data. Most canal lengths matched well, but Gadidbra minor was found to be shorter than officially reported. Irrigation potentials were also estimated and found to match closely with official data, except for Gadidbra minor which had lower potential than expected due to its shorter length. Land use/land cover of the study area was classified, finding agricultural land covers 48.64% of the total area.
ANALYSIS OF LAND USE AND LAND COVER CHANGE OF BANGALORE URBAN USING REMOTE SE...Cynthia King
This study analyzed land use and land cover change in Bangalore, India from 1992 to 2016 using remote sensing and GIS techniques. Landsat images from 1992 to 2016 were classified into four land cover classes: water, vegetation, built-up, and others. The analysis found that water coverage decreased by 72% over this period due to encroachment. Vegetation coverage also decreased by 35% as more land was converted to built-up areas. In contrast, built-up coverage increased exponentially by 152% as the city expanded in an unsustainable manner by developing vegetation and open lands on the periphery.
Pradeep Kumar Bisen has over 3 years of experience in GIS, remote sensing, satellite image processing and agriculture. He has a M.Tech in remote sensing and GIS from the Indian Institute of Remote Sensing and has worked on projects related to network analysis, site suitability, land use/land cover mapping, and drought assessment using satellite data. Currently he works as a GIS and remote sensing analyst at the National Crop Forecast Centre generating indices from optical and microwave satellite data for crop condition assessment and acreage estimation.
The document summarizes India's Earth observation programme. It discusses successful launches of satellites like INSAT-3DR, PSLV-C34 carrying 20 satellites, and PSLV rockets carrying IRNSS satellites. Currently operational missions include Oceansat-2, RISAT-1, Resourcesat-2 for applications like weather, climate, oceanography. Future missions through 2020 include Cartosat-2E, GISAT-1, RISAT-1A, Oceansat-3 for cartography, disaster management and ocean applications. It also discusses data and services provided by MOSDAC for meteorology, oceanography, cyclone tracking, and intense rainfall monitoring. Land based applications through V
ABUBAKAR Remote Sensing Application In Civil Engineering.pptxAbubakarKhan193120
Remote sensing uses sensors to acquire information about objects without physical contact. It works by measuring radiation scattered from the sun. Civil engineering applications of remote sensing include resource exploration, environmental studies, land use mapping, site analysis, hazard monitoring, town planning, urban development, water resource management, and terrain mapping. Remote sensing provides useful data to support infrastructure projects and address various challenges in civil engineering.
Remote sensing involves obtaining information about an area through analysis of physical data collected from a distance by devices without direct contact. It has been used since the 1850s for aerial photography from balloons and developed further for military purposes. Key concepts include data acquisition using various energy sources and sensors, data analysis including interpretation of imagery, and applications in ecology such as monitoring terrestrial, aquatic and animal environments as well as ecological damage. Geographic information systems (GIS) integrate spatial and non-spatial data for managing, analyzing and visualizing information. GIS techniques include data capture, storage, management, retrieval, analysis and display. GIS has many applications including environmental studies and improving understanding of processes and human activities.
Development of a Java-based application for environmental remote sensing data...IJECEIAES
Air pollution is one of the most serious problems the world faces today. It is highly necessary to monitor pollutants in real-time to anticipate and reduce damages caused in several fields of activities. Likewise, it is necessary to provide decision makers with useful and updated environmental data. As a solution to a part of the above-mentioned necessities, we developed a Java-based application software to collect, process and visualize several environmental and pollution data, acquired from the Mediterranean Dialog earth Observatory (MDEO) platform [1]. This application will amass data of Morocco area from EUMETSAT satellites, and will decompress, filter and classify the received datasets. Then we will use the processed data to build an interactive environmental real-time map of Morocco. This should help finding out potential correlations between pollutants and emitting sources.
Weather balloons are high-altitude meteorological balloons particularly used for carrying scientific payloads into the upper atmosphere. These data are obtained by using an instrument called as radiosonde which is attached to the helium filled weather balloon to measure the meteorological data as it ascends up into the atmosphere. For more than 100 years, weather balloons have given valuable information for climate and meteorological research. In this paper, the radiosonde module is designed with negligible risk of failure and cost effectiveness. The instruments to be fixed along with the weather balloon are logging camera, temperature sensor, pressure sensor, humidity sensor, global positioning system (GPS) module and a power source. This module is used to measure and log the basic weather parameters such as pressure, temperature, humidity and this also captures the picture of a particular locality with the help of a microcontroller. This proposed work is useful for observing high altitude weather data which is essential for predicting natural disasters. Further more, it is helpful to analyze the climatological and weather details of a particular region it also plays an important role in estimating agricultural models.
This document provides an overview of a course on Geographical Information Systems (GIS). It discusses the course title, code, semester, and units which include an introduction to GIS and its components. The document then describes technologies used for spatial data like GPS, remote sensing, and GIS. It provides examples of how these technologies work and their applications. Finally, the document summarizes the functions of GIS like data collection, management, analysis, and visualization.
Module 10 - Section 4: ICTs for understanding and monitoring the environment ...Richard Labelle
This document discusses how information and communication technologies (ICTs) can be used for environmental observation and addressing climate change. Satellite-based remote sensing platforms provide global earth observation data on a long-term and repetitive basis. This data is captured, analyzed, stored and shared using ICTs through systems like the Global Earth Observation System of Systems and cloud-based data portals. The combination of earth observation data and geographic information systems allows users to visualize and understand environmental changes and mitigate climate change impacts.
The document discusses photogrammetry and remote sensing. It defines remote sensing as obtaining information about an object without physical contact by sampling electromagnetic radiation. Remote sensing uses sensors on satellites and aircraft to capture radiation reflected or emitted from Earth's surface features. This data provides information on resources, weather, and the environment over large areas quickly. Common sensors mentioned include Landsat, MODIS, ASTER, and radar. Applications of remote sensing data include urban planning, agriculture, natural resource management, and national security.
Remote sensing, GIS and GPS can be used together in agriculture to map field boundaries, monitor crop health, estimate crop yields, assess drought conditions, identify pests and diseases, and enable precision agriculture. GPS provides location data, remote sensing provides aerial/satellite imagery, and GIS integrates the data to create maps and analytics for various agricultural applications like irrigation management, fertilizer recommendations, and variable rate field applications. When combined, these technologies provide valuable tools to farmers for improving crop production and managing resources efficiently.
Application of Remote Sensing GIS in Agriculture.pdfCrystal Sanchez
This document discusses the application of remote sensing and GIS in agriculture. It begins by providing context on the importance of agriculture in India and the need for timely information. It then defines remote sensing as acquiring information without physical contact and GIS as combining location data with qualitative and quantitative information through maps. The document outlines how remote sensing and GIS can be used together to identify suitable land, monitor crop health, assess damage for insurance purposes, and map soil nutrients. It concludes that these technologies allow tasks like yield estimation and damage assessment to be completed faster and more accurately than traditional methods, helping balance inputs and outputs for more sustainable agriculture.
IRJET- Land Use & Land Cover Change Detection using G.I.S. & Remote SensingIRJET Journal
This document discusses land use and land cover change detection in Vadodara, India between 1998 and 2008 using remote sensing and GIS techniques. Specifically, it analyzed Landsat satellite images from those two decades to map and classify land use, including built up area, vegetation, vacant land, and water bodies. The methodology involved image preprocessing like geometric correction and radiometric normalization. Images were then enhanced and classified using both supervised and unsupervised classification. Comparing the classified maps from 1998 and 2008 allowed analyzing changes in land use over that 10-year period and calculating the rate of land consumption. The study aimed to provide information to urban planners for predicting future growth and avoiding problems associated with rapid urbanization.
Soil mapping , remote sensing and use of sensors in precision farmingDr. M. Kumaresan Hort.
Soil mapping involves identifying different soil types, recording their properties and locations on maps. Soil maps show the spatial distribution of soils and are used for land evaluation, planning, and environmental protection. Digital soil mapping uses statistical, data mining and GIS tools to create more detailed and accurate soil maps. Remote sensing uses electromagnetic radiation to image land, oceans, and the atmosphere from ground, air, or space. It provides data that can be used to identify crops, estimate yields, and monitor land and crop conditions. Precision farming uses remote sensing and GNSS data in geographical information systems to help make crop management decisions.
This document discusses geostatistics and its applications in geoinformatics. It begins with introducing key concepts like remote sensing, GIS, GPS and their history. It then discusses spatial sampling designs and geostatistics, which involves incorporating both statistical distribution and spatial correlation of sample data. Common applications of geostatistics and geoinformatics discussed include agriculture management, environmental management, infrastructure management and crisis management using remote sensing. It concludes with discussing different spatial sampling techniques like contiguous unit based spatial sampling and stratified contiguous unit based spatial sampling.
This document contains a laboratory manual for a Digital Image Processing course for final year engineering students. It includes 10 MATLAB programs covering topics like image attribute extraction, negation, transformations, histogram processing, smoothing, sharpening, edge detection, morphological operations, pseudo coloring, and discrete cosine transform/inverse discrete cosine transform computation. It also provides instructions for labs, a quiz on digital image processing concepts, guidelines for conducting viva exams, and evaluating student performance. The overall aim is to help students enhance their understanding of digital image processing concepts through practical sessions.
This document contains information about a laboratory manual for a Digital Image Processing course. It includes the vision, mission, and objectives of the Electronics and Telecommunication department. It describes the contents of the laboratory manual, which contains practical lab sessions to enhance understanding of various aspects related to digital image processing. The document recommends that students thoroughly review the manual to better understand theoretical concepts in books through practical aspects.
DOCTORAL SEMINAR on remote sensing in AgricultureAmanDohre
This document summarizes a doctoral seminar on recent advances in applying remote sensing to fruit crop production. It discusses the historical development of remote sensing, key principles and stages in remote sensing systems, different platforms (ground, airborne, spaceborne) and sensors used. Applications of remote sensing in fruit crops include estimating crop areas, identifying diseases/pests, assessing water stress, and recommending fertilizer doses. The document also outlines various remote sensing organizations and provides an example of research on using drones to map mango yields based on tree structure.
Identification Of Ground Water Potential Zones In Tamil Nadu By Remote Sensin...IJERA Editor
A case study was conducted to find out the groundwater potential zones in Salem, Erode and Namakkal districts, Tamil Nadu, India with an aerial extent of 360.60 km2. The thematic maps such as geology, geomorphology, soil hydrological group, land use / land cover and drainage map were prepared for the study area. The Digital Elevation Model (DEM) has been generated from the 10 m interval contour lines (which is derived from SOI, Toposheet 1:25000 scale) and obtained the slope (%) of the study area. The groundwater potential zones were obtained by overlaying all the thematic maps in terms of weighted overlay methods using the spatial analysis tool in Arc GIS 9.3. During weighted overlay analysis, the ranking has been given for each individual parameter of each thematic map and weights were assigned according to the influence such as soil −25%, geomorphology − 25%, land use/land cover −25%, slope − 15%, lineament − 5% and drainage / streams − 5% and find out the potential zones in terms of good, moderate and poor zones with the area of 49.70 km2, 261.61 km2 and 46.04 km2 respectively. The potential zone wise study area was overlaid with village boundary map and the village wise groundwater potential zones with three categories such as good, moderate and poor zones were obtained. This GIS based output result was validated by conducting field survey by randomly selecting wells in different villages using GPS instruments. The coordinates of each well location were obtained by GPS and plotted in the GIS platform and it was clearly shown that the well coordinates were exactly seated with the classified zones.
Delineation of irrigation infrastructural, potential and land useIAEME Publication
This study assessed irrigation infrastructure in Muzaffarnagar district, India using satellite imagery. The main canals are Tikri Branch, Nirpura Branch, and Kurthal Branch, with several minor canals branching off. Satellite imagery was used to measure canal lengths and compare to official data. Most canal lengths matched well, but Gadidbra minor was found to be shorter than officially reported. Irrigation potentials were also estimated and found to match closely with official data, except for Gadidbra minor which had lower potential than expected due to its shorter length. Land use/land cover of the study area was classified, finding agricultural land covers 48.64% of the total area.
ANALYSIS OF LAND USE AND LAND COVER CHANGE OF BANGALORE URBAN USING REMOTE SE...Cynthia King
This study analyzed land use and land cover change in Bangalore, India from 1992 to 2016 using remote sensing and GIS techniques. Landsat images from 1992 to 2016 were classified into four land cover classes: water, vegetation, built-up, and others. The analysis found that water coverage decreased by 72% over this period due to encroachment. Vegetation coverage also decreased by 35% as more land was converted to built-up areas. In contrast, built-up coverage increased exponentially by 152% as the city expanded in an unsustainable manner by developing vegetation and open lands on the periphery.
Pradeep Kumar Bisen has over 3 years of experience in GIS, remote sensing, satellite image processing and agriculture. He has a M.Tech in remote sensing and GIS from the Indian Institute of Remote Sensing and has worked on projects related to network analysis, site suitability, land use/land cover mapping, and drought assessment using satellite data. Currently he works as a GIS and remote sensing analyst at the National Crop Forecast Centre generating indices from optical and microwave satellite data for crop condition assessment and acreage estimation.
The document summarizes India's Earth observation programme. It discusses successful launches of satellites like INSAT-3DR, PSLV-C34 carrying 20 satellites, and PSLV rockets carrying IRNSS satellites. Currently operational missions include Oceansat-2, RISAT-1, Resourcesat-2 for applications like weather, climate, oceanography. Future missions through 2020 include Cartosat-2E, GISAT-1, RISAT-1A, Oceansat-3 for cartography, disaster management and ocean applications. It also discusses data and services provided by MOSDAC for meteorology, oceanography, cyclone tracking, and intense rainfall monitoring. Land based applications through V
ABUBAKAR Remote Sensing Application In Civil Engineering.pptxAbubakarKhan193120
Remote sensing uses sensors to acquire information about objects without physical contact. It works by measuring radiation scattered from the sun. Civil engineering applications of remote sensing include resource exploration, environmental studies, land use mapping, site analysis, hazard monitoring, town planning, urban development, water resource management, and terrain mapping. Remote sensing provides useful data to support infrastructure projects and address various challenges in civil engineering.
Remote sensing involves obtaining information about an area through analysis of physical data collected from a distance by devices without direct contact. It has been used since the 1850s for aerial photography from balloons and developed further for military purposes. Key concepts include data acquisition using various energy sources and sensors, data analysis including interpretation of imagery, and applications in ecology such as monitoring terrestrial, aquatic and animal environments as well as ecological damage. Geographic information systems (GIS) integrate spatial and non-spatial data for managing, analyzing and visualizing information. GIS techniques include data capture, storage, management, retrieval, analysis and display. GIS has many applications including environmental studies and improving understanding of processes and human activities.
Development of a Java-based application for environmental remote sensing data...IJECEIAES
Air pollution is one of the most serious problems the world faces today. It is highly necessary to monitor pollutants in real-time to anticipate and reduce damages caused in several fields of activities. Likewise, it is necessary to provide decision makers with useful and updated environmental data. As a solution to a part of the above-mentioned necessities, we developed a Java-based application software to collect, process and visualize several environmental and pollution data, acquired from the Mediterranean Dialog earth Observatory (MDEO) platform [1]. This application will amass data of Morocco area from EUMETSAT satellites, and will decompress, filter and classify the received datasets. Then we will use the processed data to build an interactive environmental real-time map of Morocco. This should help finding out potential correlations between pollutants and emitting sources.
Weather balloons are high-altitude meteorological balloons particularly used for carrying scientific payloads into the upper atmosphere. These data are obtained by using an instrument called as radiosonde which is attached to the helium filled weather balloon to measure the meteorological data as it ascends up into the atmosphere. For more than 100 years, weather balloons have given valuable information for climate and meteorological research. In this paper, the radiosonde module is designed with negligible risk of failure and cost effectiveness. The instruments to be fixed along with the weather balloon are logging camera, temperature sensor, pressure sensor, humidity sensor, global positioning system (GPS) module and a power source. This module is used to measure and log the basic weather parameters such as pressure, temperature, humidity and this also captures the picture of a particular locality with the help of a microcontroller. This proposed work is useful for observing high altitude weather data which is essential for predicting natural disasters. Further more, it is helpful to analyze the climatological and weather details of a particular region it also plays an important role in estimating agricultural models.
This document provides an overview of a course on Geographical Information Systems (GIS). It discusses the course title, code, semester, and units which include an introduction to GIS and its components. The document then describes technologies used for spatial data like GPS, remote sensing, and GIS. It provides examples of how these technologies work and their applications. Finally, the document summarizes the functions of GIS like data collection, management, analysis, and visualization.
Module 10 - Section 4: ICTs for understanding and monitoring the environment ...Richard Labelle
This document discusses how information and communication technologies (ICTs) can be used for environmental observation and addressing climate change. Satellite-based remote sensing platforms provide global earth observation data on a long-term and repetitive basis. This data is captured, analyzed, stored and shared using ICTs through systems like the Global Earth Observation System of Systems and cloud-based data portals. The combination of earth observation data and geographic information systems allows users to visualize and understand environmental changes and mitigate climate change impacts.
The document discusses photogrammetry and remote sensing. It defines remote sensing as obtaining information about an object without physical contact by sampling electromagnetic radiation. Remote sensing uses sensors on satellites and aircraft to capture radiation reflected or emitted from Earth's surface features. This data provides information on resources, weather, and the environment over large areas quickly. Common sensors mentioned include Landsat, MODIS, ASTER, and radar. Applications of remote sensing data include urban planning, agriculture, natural resource management, and national security.
Remote sensing, GIS and GPS can be used together in agriculture to map field boundaries, monitor crop health, estimate crop yields, assess drought conditions, identify pests and diseases, and enable precision agriculture. GPS provides location data, remote sensing provides aerial/satellite imagery, and GIS integrates the data to create maps and analytics for various agricultural applications like irrigation management, fertilizer recommendations, and variable rate field applications. When combined, these technologies provide valuable tools to farmers for improving crop production and managing resources efficiently.
Application of Remote Sensing GIS in Agriculture.pdfCrystal Sanchez
This document discusses the application of remote sensing and GIS in agriculture. It begins by providing context on the importance of agriculture in India and the need for timely information. It then defines remote sensing as acquiring information without physical contact and GIS as combining location data with qualitative and quantitative information through maps. The document outlines how remote sensing and GIS can be used together to identify suitable land, monitor crop health, assess damage for insurance purposes, and map soil nutrients. It concludes that these technologies allow tasks like yield estimation and damage assessment to be completed faster and more accurately than traditional methods, helping balance inputs and outputs for more sustainable agriculture.
IRJET- Land Use & Land Cover Change Detection using G.I.S. & Remote SensingIRJET Journal
This document discusses land use and land cover change detection in Vadodara, India between 1998 and 2008 using remote sensing and GIS techniques. Specifically, it analyzed Landsat satellite images from those two decades to map and classify land use, including built up area, vegetation, vacant land, and water bodies. The methodology involved image preprocessing like geometric correction and radiometric normalization. Images were then enhanced and classified using both supervised and unsupervised classification. Comparing the classified maps from 1998 and 2008 allowed analyzing changes in land use over that 10-year period and calculating the rate of land consumption. The study aimed to provide information to urban planners for predicting future growth and avoiding problems associated with rapid urbanization.
Soil mapping , remote sensing and use of sensors in precision farmingDr. M. Kumaresan Hort.
Soil mapping involves identifying different soil types, recording their properties and locations on maps. Soil maps show the spatial distribution of soils and are used for land evaluation, planning, and environmental protection. Digital soil mapping uses statistical, data mining and GIS tools to create more detailed and accurate soil maps. Remote sensing uses electromagnetic radiation to image land, oceans, and the atmosphere from ground, air, or space. It provides data that can be used to identify crops, estimate yields, and monitor land and crop conditions. Precision farming uses remote sensing and GNSS data in geographical information systems to help make crop management decisions.
This document discusses geostatistics and its applications in geoinformatics. It begins with introducing key concepts like remote sensing, GIS, GPS and their history. It then discusses spatial sampling designs and geostatistics, which involves incorporating both statistical distribution and spatial correlation of sample data. Common applications of geostatistics and geoinformatics discussed include agriculture management, environmental management, infrastructure management and crisis management using remote sensing. It concludes with discussing different spatial sampling techniques like contiguous unit based spatial sampling and stratified contiguous unit based spatial sampling.
This document contains a laboratory manual for a Digital Image Processing course for final year engineering students. It includes 10 MATLAB programs covering topics like image attribute extraction, negation, transformations, histogram processing, smoothing, sharpening, edge detection, morphological operations, pseudo coloring, and discrete cosine transform/inverse discrete cosine transform computation. It also provides instructions for labs, a quiz on digital image processing concepts, guidelines for conducting viva exams, and evaluating student performance. The overall aim is to help students enhance their understanding of digital image processing concepts through practical sessions.
This document contains information about a laboratory manual for a Digital Image Processing course. It includes the vision, mission, and objectives of the Electronics and Telecommunication department. It describes the contents of the laboratory manual, which contains practical lab sessions to enhance understanding of various aspects related to digital image processing. The document recommends that students thoroughly review the manual to better understand theoretical concepts in books through practical aspects.
This document summarizes the challenges of water scarcity and its effects on the future. It discusses that erratic development goals have endangered future generations and highlights threats of water scarcity. The key causes of water scarcity mentioned are overpopulation, pollution, agriculture, and improper government policies. Effects discussed include lack of drinking water, hunger, lack of education, and sanitation issues. The document concludes that sustainable approaches to water resource management are needed to ensure availability for all.
The three main ways to store water discussed in the document are groundwater storage, small reservoir storage, and large reservoir storage behind dams. Each has comparative advantages and limitations. Groundwater storage has low evaporation loss and is available on demand but recharge is slow and contamination can be an issue. Small reservoirs are responsive to rainfall with low unit costs but have high evaporation losses and lack carryover storage. Large reservoirs provide large, reliable yields with flood control and hydropower benefits but require complex operations and management and have high upfront costs and potential environmental and social impacts. An integrated approach combining all three storage methods can achieve substantial gains.
Leaders from 193 countries came together in 2015 to address global challenges and create a sustainable future. They established 17 Sustainable Development Goals to eliminate poverty, hunger, disease and climate change by 2030. The UNDP works to implement the goals in nearly 170 countries by 2030 through initiatives to promote economic growth, education, healthcare, gender equality and more.
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...IJECEIAES
Climate change's impact on the planet forced the United Nations and governments to promote green energies and electric transportation. The deployments of photovoltaic (PV) and electric vehicle (EV) systems gained stronger momentum due to their numerous advantages over fossil fuel types. The advantages go beyond sustainability to reach financial support and stability. The work in this paper introduces the hybrid system between PV and EV to support industrial and commercial plants. This paper covers the theoretical framework of the proposed hybrid system including the required equation to complete the cost analysis when PV and EV are present. In addition, the proposed design diagram which sets the priorities and requirements of the system is presented. The proposed approach allows setup to advance their power stability, especially during power outages. The presented information supports researchers and plant owners to complete the necessary analysis while promoting the deployment of clean energy. The result of a case study that represents a dairy milk farmer supports the theoretical works and highlights its advanced benefits to existing plants. The short return on investment of the proposed approach supports the paper's novelty approach for the sustainable electrical system. In addition, the proposed system allows for an isolated power setup without the need for a transmission line which enhances the safety of the electrical network
A review on techniques and modelling methodologies used for checking electrom...nooriasukmaningtyas
The proper function of the integrated circuit (IC) in an inhibiting electromagnetic environment has always been a serious concern throughout the decades of revolution in the world of electronics, from disjunct devices to today’s integrated circuit technology, where billions of transistors are combined on a single chip. The automotive industry and smart vehicles in particular, are confronting design issues such as being prone to electromagnetic interference (EMI). Electronic control devices calculate incorrect outputs because of EMI and sensors give misleading values which can prove fatal in case of automotives. In this paper, the authors have non exhaustively tried to review research work concerned with the investigation of EMI in ICs and prediction of this EMI using various modelling methodologies and measurement setups.
ACEP Magazine edition 4th launched on 05.06.2024Rahul
This document provides information about the third edition of the magazine "Sthapatya" published by the Association of Civil Engineers (Practicing) Aurangabad. It includes messages from current and past presidents of ACEP, memories and photos from past ACEP events, information on life time achievement awards given by ACEP, and a technical article on concrete maintenance, repairs and strengthening. The document highlights activities of ACEP and provides a technical educational article for members.
Literature Review Basics and Understanding Reference Management.pptxDr Ramhari Poudyal
Three-day training on academic research focuses on analytical tools at United Technical College, supported by the University Grant Commission, Nepal. 24-26 May 2024
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressionsVictor Morales
K8sGPT is a tool that analyzes and diagnoses Kubernetes clusters. This presentation was used to share the requirements and dependencies to deploy K8sGPT in a local environment.
Embedded machine learning-based road conditions and driving behavior monitoringIJECEIAES
Car accident rates have increased in recent years, resulting in losses in human lives, properties, and other financial costs. An embedded machine learning-based system is developed to address this critical issue. The system can monitor road conditions, detect driving patterns, and identify aggressive driving behaviors. The system is based on neural networks trained on a comprehensive dataset of driving events, driving styles, and road conditions. The system effectively detects potential risks and helps mitigate the frequency and impact of accidents. The primary goal is to ensure the safety of drivers and vehicles. Collecting data involved gathering information on three key road events: normal street and normal drive, speed bumps, circular yellow speed bumps, and three aggressive driving actions: sudden start, sudden stop, and sudden entry. The gathered data is processed and analyzed using a machine learning system designed for limited power and memory devices. The developed system resulted in 91.9% accuracy, 93.6% precision, and 92% recall. The achieved inference time on an Arduino Nano 33 BLE Sense with a 32-bit CPU running at 64 MHz is 34 ms and requires 2.6 kB peak RAM and 139.9 kB program flash memory, making it suitable for resource-constrained embedded systems.
A SYSTEMATIC RISK ASSESSMENT APPROACH FOR SECURING THE SMART IRRIGATION SYSTEMSIJNSA Journal
The smart irrigation system represents an innovative approach to optimize water usage in agricultural and landscaping practices. The integration of cutting-edge technologies, including sensors, actuators, and data analysis, empowers this system to provide accurate monitoring and control of irrigation processes by leveraging real-time environmental conditions. The main objective of a smart irrigation system is to optimize water efficiency, minimize expenses, and foster the adoption of sustainable water management methods. This paper conducts a systematic risk assessment by exploring the key components/assets and their functionalities in the smart irrigation system. The crucial role of sensors in gathering data on soil moisture, weather patterns, and plant well-being is emphasized in this system. These sensors enable intelligent decision-making in irrigation scheduling and water distribution, leading to enhanced water efficiency and sustainable water management practices. Actuators enable automated control of irrigation devices, ensuring precise and targeted water delivery to plants. Additionally, the paper addresses the potential threat and vulnerabilities associated with smart irrigation systems. It discusses limitations of the system, such as power constraints and computational capabilities, and calculates the potential security risks. The paper suggests possible risk treatment methods for effective secure system operation. In conclusion, the paper emphasizes the significant benefits of implementing smart irrigation systems, including improved water conservation, increased crop yield, and reduced environmental impact. Additionally, based on the security analysis conducted, the paper recommends the implementation of countermeasures and security approaches to address vulnerabilities and ensure the integrity and reliability of the system. By incorporating these measures, smart irrigation technology can revolutionize water management practices in agriculture, promoting sustainability, resource efficiency, and safeguarding against potential security threats.
RAT: Retrieval Augmented Thoughts Elicit Context-Aware Reasoning in Long-Hori...
wmo-td_1182_en.pdf
1.
2. Satellite Remote Sensing and
GIS Applications in
Agricultural Meteorology
Proceedings of the Training Workshop
7-11 July, 2003, Dehra Dun, India
Editors
M.V.K. Sivakumar
P.S. Roy
K. Harmsen
S.K. Saha
Sponsors
World Meteorological Organization (WMO)
India Meteorological Department (IMD)
Centre for Space Science and Technology Education in Asia and the Pacific
(CSSTEAP)
Indian Institute of Remote Sensing (IIRS)
National Remote Sensing Agency (NRSA) and
Space Application Centre (SAC)
AGM-8
WMO/TD No. 1182
World Meteorological Organisation
7bis, Avenue de la Paix
1211 Geneva 2
Switzerland
2004
3. Published by
World Meteorological Organisation
7bis, Avenue de la Paix
1211 Geneva 2, Switzerland
World Meteorological Organisation
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system,
or transmitted in any form or by any means, electronic, mechanical, photocopying, recording,
or otherwise, without the prior written consent of the copyright owner.
Typesetting and Printing :
M/s Bishen Singh Mahendra Pal Singh
23-A New Connaught Place, P.O. Box 137,
Dehra Dun -248001 (Uttaranchal), INDIA
Ph.: 91-135-2715748 Fax- 91-135-2715107
E.mail: bsmps@vsnl.com
Website: http://www.bishensinghbooks.com
5. CONTENTS
Satellite Remote Sensing and GIS Applications in Agricultural .... 1
Meteorology and WMO Satellite Activities
– M.V.K. Sivakumar and Donald E. Hinsman
Principles of Remote Sensing ......... 23
Shefali Aggarwal
Earth Resource Satellites ......... 39
– Shefali Aggarwal
Meteorological Satellites ......... 67
– C.M. Kishtawal
Digital Image Processing ......... 81
– Minakshi Kumar
Fundamentals of Geographical Information System ......... 103
– P.L.N. Raju
Fundamentals of GPS ......... 121
– P.L.N. Raju
Spatial Data Analysis ......... 151
– P.L.N. Raju
Retrieval of Agrometeorological Parameters using Satellite ......... 175
Remote Sensing data
– S. K. Saha
Retrieval of Agrometeorological Parameters from Satellites ......... 195
– C.M. Kishtawal
Remote Sensing and GIS Application in Agro-ecological ......... 213
zoning
– N.R. Patel
Crop Growth Modeling and its Applications in ......... 235
Agricultural Meteorology
– V. Radha Krishna Murthy
6. Crop Growth and Productivity Monitoring and Simulation ......... 263
using Remote Sensing and GIS
– V.K. Dadhwal
Droughts & Floods Assessment and Monitoring using ......... 291
Remote Sensing and GIS
– A.T. Jeyaseelan
Water and Wind induced Soil Erosion Assessment and ......... 315
Monitoring using Remote Sensing and GIS
– S.K. Saha
Satellite-based Weather Forecasting ......... 331
– S.R. Kalsi
Satellite-based Agro-advisory Service ......... 347
– H. P. Das
Forest Fire and Degradation Assessment using Satellite Remote ........ 361
Sensing and Geographic Information System
– P.S. Roy
Desert Locust Monitoring System–Remote Sensing and GIS ......... 401
based approach
– D. Dutta, S. Bhatawdekar, B. Chandrasekharan, J.R. Sharma,
S. Adiga, Duncan Wood and Adrian McCardle
Workshop Evaluation ......... 425
– M.V.K. Sivakumar
7. SATELLITE REMOTE SENSING AND GIS
APPLICATIONS IN AGRICULTURAL METEO-
ROLOGY AND WMO SATELLITE ACTIVITIES
M.V.K. Sivakumar and Donald E. Hinsman
Agricultural Meteorology Division and Satellite Activities Office
World Meteorological Organization (WMO), 7bis Avenue de la Paix,
1211 Geneva 2, Switzerland
Abstract : Agricultural planning and use of agricultural technologies need
applications of agricultural meteorology. Satellite remote sensing technology is
increasingly gaining recognition as an important source of agrometeorological data
as it can complement well the traditional methods agrometeorological data
collection. Agrometeorologists all over the world are now able to take advantage
of a wealth of observational data, product and services flowing from specially
equipped and highly sophisticated environmental observation satellites. In addition,
Geographic Information Systems (GIS) technology is becoming an essential tool
for combining various map and satellite information sources in models that simulate
the interactions of complex natural systems. The Commission for Agricultural
Meteorology of WMO has been active in the area of remote sensing and GIS
applications in agrometeorology. The paper provides a brief overview of the satellite
remote sensing and GIS Applications in agricultural meteorology along with a
description of the WMO Satellite Activities Programme. The promotion of new
specialised software should make the applications of the various devices easier,
bearing in mind the possible combination of several types of inputs such as data
coming from standard networks, radar and satellites, meteorological and
climatological models, digital cartography and crop models based on the scientific
acquisition of the last twenty years.
INTRODUCTION
Agricultural planning and use of agricultural technologies need application
of agricultural meteorology. Agricultural weather and climate data systems are
necessary to expedite generation of products, analyses and forecasts that affect
Satellite Remote Sensing and GIS Applications in Agricultural Meteorology
pp. 1-21
8. 2 Satellite Remote Sensing and GIS Applications in Agricultural Meteorology
agricultural cropping and management decisions, irrigation scheduling,
commodity trading and markets, fire weather management and other
preparedness for calamities, and ecosystem conservation and management.
Agrometeorological station networks are designed to observe the data of
meteorological and biological phenomena together with supplementary data
as disasters and crop damages occur. The method of observation can be
categorized into two major classes, manually observed and automatic weather
stations (AWS). A third source for agrometeorological data that is gaining
recognition for its complementary nature to the traditional methods is satellite
remote sensing technology.
Remotely sensed data and AWS systems provide in many ways an
enhanced and very feasible alternative to manual observation with a very short
time delay between data collection and transmission. In certain countries where
only few stations are in operation as in Northern Turkmenistan (Seitnazarov,
1999), remotely sensed data can improve information on crop conditions for
an early warning system. Due to the availability of new tools, such as
Geographic Information Systems (GIS), management of an incredible quantity
of data such as traditional digital maps, database, models etc., is now possible.
The advantages are manifold and highly important, especially for the fast cross-
sector interactions and the production of synthetic and lucid information for
decision-makers. Remote sensing provides the most important informative
contribution to GIS, which furnishes basic informative layers in optimal time
and space resolutions.
In this paper, a brief overview of the satellite remote sensing and GIS
applications in agricultural meteorology is presented along with a description
of the WMO Satellite Activities Programme. Details of the various applications
alluded to briefly in this paper, can be found in the informative papers
prepared by various experts who will be presenting them in the course of this
workshop.
The Commission for Agricultural Meteorology (CAgM) of WMO, Remote
Sensing and GIS
Agricultural meteorology had always been an important component of the
National Meteorological Services since their inception. A formal Commission
for Agricultural Meteorology (CAgM) which was appointed in 1913 by the
International Meteorological Organization (IMO), became the foundation of
the CAgM under WMO in 1951.
9. M.V.K. Sivakumar and Donald E. Hinsman 3
The WMO Agricultural Meteorology Programme is coordinated by
CAgM. The Commission is responsible for matters relating to applications of
meteorology to agricultural cropping systems, forestry, and agricultural land
use and livestock management, taking into account meteorological and
agricultural developments both in the scientific and practical fields and the
development of agricultural meteorological services of Members by transfer of
knowledge and methodology and by providing advice.
CAgM recognized the potential of remote sensing applications in
agricultural meteorology early in the 70s and at its sixth session in Washington
in 1974 the Commission agreed that its programme should include studies
on the application of remote sensing techniques to agrometeorological problems
and decided to appoint a rapporteur to study the existing state of the
knowledge of remote sensing techniques and to review its application to
agrometeorological research and services. At its seventh session in Sofia, Bulgaria
in 1979, the Commission reviewed the report submitted by Dr A.D.
Kleschenko (USSR) and Dr J.C. Harlan Jr (USA) and noted that there was a
promising future for the use in agrometeorology of data from spacecraft and
aircraft and that rapid progress in this field required exchange of information
on achievements in methodology and data collection and interpretation. The
Commission at that time noted that there was a demand in almost all countries
for a capability to use satellite imagery in practical problems of agrometeorology.
The Commission continued to pay much attention to both remote sensing
and GIS applications in agrometeorology in all its subsequent sessions up to
the 13th
session held in Ljubljana, Slovenia in 2002. Several useful publications
including Technical Notes and CAgM Reports were published covering the
use of remote sensing for obtaining agrometeorological information
(Kleschenko, 1983), operational remote sensing systems in agriculture
(Kanemasu and Filcroft, 1992), satellite applications to agrometeorology and
technological developments for the period 1985-89 (Seguin, 1992), statements
of guidance regarding how well satellite capabilities meet WMO user
requirements in agrometeorology (WMO, 1998, 2000) etc. At the session in
Slovenia in 2002, the Commission convened an Expert Team on Techniques
(including Technologies such as GIS and Remote Sensing) for Agroclimatic
Characterization and Sustainable Land Management.
The Commission also recognized that training of technical personnel to
acquire, process and interpret the satellite imagery was a major task. It was
felt that acquisition of satellite data was usually much easier than the
interpretation of data for specific applications that were critical for the
10. 4 Satellite Remote Sensing and GIS Applications in Agricultural Meteorology
assessment and management of natural resources. In this regard, the
Commission pointed out that long-term planning and training of technical
personnel was a key ingredient in ensuring full success in the use of current
and future remote sensing technologies that could increase and sustain
agricultural production, especially in the developing countries. In this
connection, WMO already organized a Training Seminar on GIS and
Agroecological Zoning in Kuala Lumpur, Malaysia in May 2000 in which six
participants from Malaysia and 12 from other Asian and the South-West Pacific
countries participated. The programme for the seminar dealt with
meteorological and geographical databases, statistical analyses, spatialization,
agro-ecological classification, overlapping of agroecological zoning with
boundary layers, data extraction, monitoring system organization and bulletins.
The training workshop currently being organized in Dehradun is in
response to the recommendations of the Commission session in Slovenia in
2002 and it should help the participants from the Asian countries in learning
new skills and updating their current skills in satellite remote sensing and
GIS applications in agricultural meteorology.
GIS APPLICATIONS IN AGROMETEOROLOGY
A GIS generally refers to a description of the characteristics and tools used
in the organization and management of geographical data. The term GIS is
currently applied to computerised storage, processing and retrieval systems
that have hardware and software specially designed to cope with geographically
referenced spatial data and corresponding informative attribute. Spatial data
are commonly in the form of layers that may depict topography or
environmental elements. Nowadays, GIS technology is becoming an essential
tool for combining various map and satellite information sources in models
that simulate the interactions of complex natural systems. A GIS can be used
to produce images, not just maps, but drawings, animations, and other
cartographic products.
The increasing world population, coupled with the growing pressure on
the land resources, necessitates the application of technologies such as GIS to
help maintain a sustainable water and food supply according to the
environmental potential. The “sustainable rural development” concept envisages
an integrated management of landscape, where the exploitation of natural
resources, including climate, plays a central role. In this context,
agrometeorology can help reduce inputs, while in the framework of global
11. M.V.K. Sivakumar and Donald E. Hinsman 5
change, it helps quantify the contribution of ecosystems and agriculture to
carbon budget (Maracchi, 1991). Agroclimatological analysis can improve the
knowledge of existing problems allowing land planning and optimization of
resource management. One of the most important agroclimatological
applications is the climatic risk evaluation corresponding to the possibility that
certain meteorological events could happen, damaging crops or infrastructure.
At the national and local level, possible GIS applications are endless. For
example, agricultural planners might use geographical data to decide on the
best zones for a cash crop, combining data on soils, topography, and rainfall
to determine the size and location of biologically suitable areas. The final
output could include overlays with land ownership, transport, infrastructure,
labour availability, and distance to market centres.
The ultimate use of GIS lies in its modelling capability, using real world
data to represent natural behaviour and to simulate the effect of specific
processes. Modelling is a powerful tool for analyzing trends and identifying
factors that affect them, or for displaying the possible consequences of human
activities that affect the resource availability.
In agrometeorology, to describe a specific situation, we use all the
information available on the territory: water availability, soil types, forest and
grasslands, climatic data, geology, population, land-use, administrative
boundaries and infrastructure (highways, railroads, electricity or
communication systems). Within a GIS, each informative layer provides to
the operator the possibility to consider its influence to the final result. However
more than the overlap of the different themes, the relationship of the numerous
layers is reproduced with simple formulas or with complex models. The final
information is extracted using graphical representation or precise descriptive
indexes.
In addition to classical applications of agrometeorology, such as crop yield
forecasting, uses such as those of the environmental and human security are
becoming more and more important. For instance, effective forest fire
prevention needs a series of very detailed information on an enormous scale.
The analysis of data, such as the vegetation coverage with different levels of
inflammability, the presence of urban agglomeration, the presence of roads
and many other aspects, allows the mapping of the areas where risk is greater.
The use of other informative layers, such as the position of the control points
and resource availability (staff, cars, helicopters, aeroplanes, fire fighting
12. 6 Satellite Remote Sensing and GIS Applications in Agricultural Meteorology
equipment, etc.), can help the decision-makers in the management of the
ecosystems. Monitoring the resources and the meteorological conditions
therefore allows, the consideration of the dynamics of the system, with more
adherence to reality. For instance, Figure 1 shows the informative layers used
for the evaluation of fire risk in Tuscany (Italy). The final map is the result of
the integration of satellite data with territorial data, through the use of
implemented GIS technologies (Romanelli et al., 1998).
Figure 1. Informative layers for the evaluation of fire risk index (Maracchi et al., 2000).
Land use Distance road Starting point
Quota Slope Aspect
Fire risk
13. M.V.K. Sivakumar and Donald E. Hinsman 7
These maps of fire risk, constitute a valid tool for foresters and for
organisation of the public services. At the same time, this new informative
layer may be used as the base for other evaluations and simulations. Using
meteorological data and satellite real-time information, it is possible to diversify
the single situations, advising the competent authorities when the situation
moves to hazard risks. Modelling the ground wind profile and taking into
account the meteorological conditions, it is possible to advise the operators
of the change in the conditions that can directly influence the fire, allowing
the modification of the intervention strategies.
An example of preliminary information system to country scale is given
by the SISP (Integrated information system for monitoring cropping season
by meteorological and satellite data), developed to allow the monitoring of
the cropping season and to provide an early warning system with useful
information about evolution of crop conditions (Di Chiara and Maracchi,
1994). The SISP uses:
z Statistical analysis procedures on historical series of rainfall data to produce
agroclimatic classification;
z A crop (millet) simulation model to estimate millet sowing date and to
evaluate the effect of the rainfall distribution on crop growth and yield;
z NOAA-NDVI image analysis procedures in order to monitor vegetation
condition;
z Analysis procedures of Meteosat images of estimated rainfall for early
prediction of sowing date and risk areas.
The results of SISP application shown for Niger (Fig. 2) are charts and
maps, which give indications to the expert of the millet conditions during
the season in Niger, with the possibility to estimate the moment of the harvest
and final production. SISP is based on the simulation of the millet growth
and it gives an index of annual productivity by administrative units. These
values, multiplied to a yield statistical factor, allow estimation of absolute
production.
By means of such systems based on modelling and remote sensing, it is
possible to extract indices relative to the main characteristics of the agricultural
season and conditions of natural systems. This system is less expensive, easily
transferable and requires minor informative layers, adapting it to the specific
requirements of the users.
14. 8 Satellite Remote Sensing and GIS Applications in Agricultural Meteorology
Figure 2. Examples of outputs of SISP (Maracchi et al., 2000).
SATELLITE REMOTE SENSING
Remote sensing provides spatial coverage by measurement of reflected and
emitted electromagnetic radiation, across a wide range of wavebands, from the
earth’s surface and surrounding atmosphere. The improvement in technical
tools of meteorological observation, during the last twenty years, has created
a favourable substratum for research and monitoring in many applications of
sciences of great economic relevance, such as agriculture and forestry. Each
waveband provides different information about the atmosphere and land
surface: surface temperature, clouds, solar radiation, processes of photosynthesis
and evaporation, which can affect the reflected and emitted radiation, detected
by satellites. The challenge for research therefore is to develop new systems
extracting this information from remotely sensed data, giving to the final users,
near-real-time information.
Over the last two decades, the development of space technology has led
to a substantial increase in satellite earth observation systems. Simultaneously,
the Information and Communication Technology (ICT) revolution has rendered
increasingly effective the processing of data for specific uses and their
instantaneous distribution on the World Wide Web (WWW).
The meteorological community and associated environmental disciplines
such as climatology including global change, hydrology and oceanography all
over the world are now able to take advantage of a wealth of observational
data, products and services flowing from specially equipped and highly
sophisticated environmental observation satellites. An environmental
Niamey, cropping season 1993
Characterizationof land productivity at Niger
CeSIAIndexformiller
Elaboratedon10years (1981-90) and120stations
Rainfall Cultural Coeff. Water balance
Longitude
15. M.V.K. Sivakumar and Donald E. Hinsman 9
observation satellite is an artificial Earth satellite providing data on the Earth
system and a Meteorological satellite is a type of environmental satellite
providing meteorological observations. Several factors make environmental
satellite data unique compared with data from other sources, and it is worthy
to note a few of the most important:
z Because of its high vantage point and broad field of view, an environmental
satellite can provide a regular supply of data from those areas of the globe
yielding very few conventional observations;
z The atmosphere is broadly scanned from satellite altitude and enables large-
scale environmental features to be seen in a single view;
z The ability of certain satellites to view a major portion of the atmosphere
continually from space makes them particularly well suited for the
monitoring and warning of short-lived meteorological phenomena; and
z The advanced communication systems developed as an integral part of
the satellite technology permit the rapid transmission of data from the
satellite, or their relay from automatic stations on earth and in the
atmosphere, to operational users.
These factors are incorporated in the design of meteorological satellites to
provide data, products and services through three major functions:
z Remote sensing of spectral radiation which can be converted into
meteorological measurements such as cloud cover, cloud motion vectors,
surface temperature, vertical profiles of atmospheric temperature, humidity
and atmospheric constituents such as ozone, snow and ice cover, ozone
and various radiation measurements;
z Collection of data from in situ sensors on remote fixed or mobile platforms
located on the earth’s surface or in the atmosphere; and
z Direct broadcast to provide cloud-cover images and other meteorological
information to users through a user-operated direct readout station.
The first views of earth from space were not obtained from satellites but
from converted military rockets in the early 1950s. It was not until 1 April
1960 that the first operational meteorological satellite, TIROS-I, was launched
16. 10 Satellite Remote Sensing and GIS Applications in Agricultural Meteorology
by the USA and began to transmit basic, but very useful, cloud imagery. This
satellite was such an effective proof of concept that by 1966 the USA had
launched a long line of operational polar satellites and its first geostationary
meteorological satellite. In 1969 the USSR launched the first of a series of
polar satellites. In 1977 geostationary meteorological satellites were also
launched and operated by Japan and by the European Space Agency (ESA).
Thus, within 18 years of the first practical demonstration by TIROS-I, a fully
operational meteorological satellite system (Fig. 3) was in place, giving routine
data coverage of most of the planet. This rapid evolution of a very expensive
new system was unprecedented and indicates the enormous value of these
satellites to meteorology and society. Some four decades after the first earth
images, new systems are still being designed and implemented, illustrating
the continued and dynamic interest in this unique source of environmental
data.
Figure 3: Nominal configuration of the space-based sub-system of the Global Observing
System in 1978.
17. M.V.K. Sivakumar and Donald E. Hinsman 11
By the year 2000, WMO Members contributing to the space-based sub-
system of the Global Observing System had grown. There were two major
constellations in the space-based Global Observing System (GOS) (Fig. 4).
One constellation was the various geostationary satellites, which operated in
an equatorial belt and provided a continuous view of the weather from roughly
70°N to 70°S. The second constellation in the current space-based GOS
comprised the polar-orbiting satellites operated by the Russian Federation,
the USA and the People’s Republic of China. The METEOR-3 series has been
operated by the Russian Federation since 1991.
Figure 4: Nominal configuration of the space-based sub-system of the Global Observing
System in 2000.
The ability of geostationary satellites to provide a continuous view of
weather systems make them invaluable in following the motion, development,
and decay of such phenomena. Even such short-term events such as severe
thunderstorms, with a life-time of only a few hours, can be successfully
recognized in their early stages and appropriate warnings of the time and area
18. 12 Satellite Remote Sensing and GIS Applications in Agricultural Meteorology
of their maximum impact can be expeditiously provided to the general public.
For this reason, its warning capability has been the primary justification for
the geostationary spacecraft. Since 71 per cent of the Earth’s surface is water
and even the land areas have many regions which are sparsely inhabited, the
polar-orbiting satellite system provides the data needed to compensate the
deficiencies in conventional observing networks. Flying in a near-polar orbit,
the spacecraft is able to acquire data from all parts of the globe in the course
of a series of successive revolutions. For these reasons the polar-orbiting satellites
are principally used to obtain: (a) daily global cloud cover; and (b) accurate
quantitative measurements of surface temperature and of the vertical variation
of temperature and water vapour in the atmosphere. There is a distinct
advantage in receiving global data acquired by a single set of observing sensors.
Together, the polar-orbiting and geostationary satellites constitute a truly global
meteorological satellite network.
Satellite data provide better coverage in time and in area extent than any
alternative. Most polar satellite instruments observe the entire planet once or
twice in a 24-hour period. Each geostationary satellite’s instruments cover
about ¼ of the planet almost continuously and there are now six geostationary
satellites providing a combined coverage of almost 75%. Satellites cover the
world’s oceans (about 70% of the planet), its deserts, forests, polar regions,
and other sparsely inhabited places. Surface winds over the oceans from satellites
are comparable to ship observations; ocean heights can be determined to a
few centimetres; and temperatures in any part of the atmosphere anywhere
in the world are suitable for computer models. It is important to make
maximum use of this information to monitor our environment. Access to these
satellite data and products is only the beginning. In addition, the ability to
interpret, combine, and make maximum use of this information must be an
integral element of national management in developed and developing
countries.
The thrust of the current generation of environmental satellites is aimed
primarily at characterizing the kinematics and dynamics of the atmospheric
circulation. The existing network of environmental satellites, forming part of
the GOS of the World Weather Watch produces real-time weather information
on a regular basis. This is acquired several times a day through direct broadcast
from the meteorological satellites by more than 1,300 stations located in 125
countries.
19. M.V.K. Sivakumar and Donald E. Hinsman 13
The ground segment of the space-based component of the GOS should
provide for the reception of signals and DCP data from operational satellites
and/or the processing, formatting and display of meaningful environmental
observation information, with a view to further distributing it in a convenient
form to local users, or over the GTS, as required. This capability is normally
accomplished through receiving and processing stations of varying complexity,
sophistication and cost.
In addition to their current satellite programmes in polar and geostationary
orbits, satellite operators in the USA (NOAA) and Europe (EUMETSAT) have
agreed to launch a series of joint polar-orbiting satellites (METOP) in 2005.
These satellites will complement the existing global array of geostationary
satellites that form part of the Global Observing System of the World
Meteorological Organization. This Initial Joint Polar System (IJPS) represents
a major cooperation programme between the USA and Europe in the field of
space activities. Europe has invested 2 billion Euros in a low earth orbit satellite
system, which will be available operationally from 2006 to 2020.
The data provided by these satellites will enable development of
operational services in improved temperature and moisture sounding for
numerical weather prediction (NWP), tropospheric/stratospheric interactions,
imagery of clouds and land/ocean surfaces, air-sea interactions, ozone and other
trace gases mapping and monitoring, and direct broadcast support to
nowcasting. Advanced weather prediction models are needed to assimilate
satellite information at the highest possible spatial and spectral resolutions.
It imposes new requirements on the precision and spectral resolution of
soundings in order to improve the quality of weather forecasts. Satellite
information is already used by fishery-fleets on an operational basis. Wind
and the resulting surface stress is the major force for oceanic motions. Ocean
circulation forecasts require the knowledge of an accurate wind field. Wind
measurements from space play an increasing role in monitoring of climate
change and variability. The chemical composition of the troposphere is
changing on all spatial scales. Increases in trace gases with long atmospheric
residence times can affect the climate and chemical equilibrium of the Earth/
Atmosphere system. Among these trace gases are methane, nitrogen dioxide,
and ozone. The chemical and dynamic state of the stratosphere influence the
troposphere by exchange processes through the tropopause. Continuous
monitoring of ozone and of (the main) trace gases in the troposphere and the
stratosphere is an essential input to the understanding of the related
atmospheric chemistry processes.
20. 14 Satellite Remote Sensing and GIS Applications in Agricultural Meteorology
WMO SPACE PROGRAMME
The World Meteorological Organization, a specialized agency of the United
Nations, has a membership of 187 states and territories (as of June 2003).
Amongst the many programmes and activities of the organization, there are
three areas which are particularly pertinent to the satellite activities:
z To facilitate world-wide cooperation in the establishment of networks for
making meteorological, as well as hydrological and other geophysical
observations and centres to provide meteorological services;
z To promote the establishment and maintenance of systems for the rapid
exchange of meteorological and related information;
z To promote the standardization of meteorological observations and ensure
the uniform publication of observations and statistics.
The Fourteenth WMO Congress, held in May 2003, initiated a new Major
Programme, the WMO Space Programme, as a cross-cutting programme to
increase the effectiveness and contributions from satellite systems to WMO
Programmes. Congress recognized the critical importance for data, products
and services provided by the World Weather Watch’s (WWW) expanded space-
based component of the Global Observing System (GOS) to WMO
Programmes and supported Programmes. During the past four years, the use
by WMO Members of satellite data, products and services has experienced
tremendous growth to the benefit of almost all WMO Programmes and
supported Programmes. The decision by the fifty-third Executive Council to
expand the space-based component of the Global Observing System to include
appropriate R&D environmental satellite missions was a landmark decision
in the history of WWW. Congress agreed that the Commission for Basic
Systems (CBS) should continue the lead role in full consultation with the other
technical commissions for the new WMO Space Programme. Congress also
decided to establish WMO Consultative Meetings on High-level Policy on
Satellite Matters. The Consultative Meetings will provide advice and guidance
on policy-related matters and maintain a high level overview of the WMO
Space Programme. The expected benefits from the new WMO Space
Programme include an increasing contribution to the development of the
WWW’s GOS, as well as to the other WMO-supported programmes and
associated observing systems through the provision of continuously improved
data, products and services, from both operational and R&D satellites, and
21. M.V.K. Sivakumar and Donald E. Hinsman 15
to facilitate and promote their wider availability and meaningful utilization
around the globe.
The main thrust of the WMO Space Programme Long-term Strategy is:
“To make an increasing contribution to the development of the WWW’s
GOS, as well as to the other WMO-supported Programmes and associated
observing systems (such as AREP’s GAW, GCOS, WCRP, HWR’s WHYCOS
and JCOMM’s implementation of GOS) through the provision of continuously
improved data, products and services, from both operational and R&D
satellites, and to facilitate and promote their wider availability and meaningful
utilization around the globe”.
The main elements of the WMO Space Programme Long-term Strategy
are as follows:
(a) Increased involvement of space agencies contributing, or with the
potential to contribute to, the space-based component of the GOS;
(b) Promotion of a wider awareness of the availability and utilization of
data, products - and their importance at levels 1, 2, 3 or 4 - and
services, including those from R&D satellites;
(c) Considerably more attention to be paid to the crucial problems
connected with the assimilation of R&D and new operational data
streams in nowcasting, numerical weather prediction systems,
reanalysis projects, monitoring climate change, chemical composition
of the atmosphere, as well as the dominance of satellite data in some
cases;
(d) Closer and more effective cooperation with relevant international
bodies;
(e) Additional and continuing emphasis on education and training;
(f) Facilitation of the transition from research to operational systems;
(g) Improved integration of the space component of the various observing
systems throughout WMO Programmes and WMO-supported
Programmes;
22. 16 Satellite Remote Sensing and GIS Applications in Agricultural Meteorology
(h) Increased cooperation amongst WMO Members to develop common
basic tools for utilization of research, development and operational
remote sensing systems.
Coordination Group for Meteorological Satellites (CGMS)
In 1972 a group of satellite operators formed the Co-ordination of
Geostationary Meteorological Satellites (CGMS) that would be expanded in
the early 1990s to include polar-orbiting satellites and changed its name -
but not its abbreviation - to the Co-ordination Group for Meteorological
Satellites. The Co-ordination Group for Meteorological Satellites (CGMS)
provides a forum for the exchange of technical information on geostationary
and polar orbiting meteorological satellite systems, such as reporting on current
meteorological satellite status and future plans, telecommunication matters,
operations, inter-calibration of sensors, processing algorithms, products and
their validation, data transmission formats and future data transmission
standards.
Since 1972, the CGMS has provided a forum in which the satellite
operators have studied jointly with the WMO technical operational aspects
of the global network, so as to ensure maximum efficiency and usefulness
through proper coordination in the design of the satellites and in the
procedures for data acquisition and dissemination.
Membership of CGMS
The table of members shows the lead agency in each case. Delegates are often
supported by other agencies, for example, ESA (with EUMETSAT), NASDA
(with Japan) and NASA (with NOAA).
The current Membership of CGMS is:
EUMETSAT joined 1987
currently CGMS Secretariat
India Meteorological Department joined 1979
Japan Meteorological Agency founder member, 1972
China Meteorological Administration joined 1989
NOAA/NESDIS founder member, 1972
Hydromet Service of the Russian Federation joined 1973
23. M.V.K. Sivakumar and Donald E. Hinsman 17
WMO joined 1973
IOC of UNESCO joined 2000
NASA joined 2002
ESA joined 2002
NASDA joined 2002
Rosaviakosmos joined 2002
WMO, in its endeavours to promote the development of a global
meteorological observing system, participated in the activities of CGMS from
its first meeting. There are several areas where joint consultations between the
satellite operators and WMO are needed. The provision of data to
meteorological centres in different parts of the globe is achieved by means of
the Global Telecommunication System (GTS) in near-real-time. This
automatically involves assistance by WMO in developing appropriate code
forms and provision of a certain amount of administrative communications
between the satellite operators.
WMO’s role within CGMS would be to state the observational and system
requirements for WMO and supported programmes as they relate to the
expanded space-based components of the GOS, GAW, GCOS and WHYCOS.
CGMS satellite operators would make their voluntary commitments to meet
the stated observational and system requirements. WMO would, through its
Members, strive to provide CGMS satellite operators with operational and pre-
operational evaluations of the benefit and impacts of their satellite systems.
WMO would also act as a catalyst to foster direct user interactions with the
CGMS satellite operators through available means such as conferences,
symposia and workshops.
The active involvement of WMO has allowed the development and
implementation of the operational ASDAR system as a continuing part of the
Global Observing System. Furthermore, the implementation of the IDCS
system was promoted by WMO and acted jointly with the satellite operators
as the admitting authority in the registration procedure for IDCPs.
The expanded space-based component of the world weather watch’s global
observing system
Several initiatives since 2000 with regard to WMO satellite activities have
culminated in an expansion of the space-based component of the Global
24. 18 Satellite Remote Sensing and GIS Applications in Agricultural Meteorology
Observing System to include appropriate Research and Development (R&D)
satellite missions. The recently established WMO Consultative Meetings on
High-Level Policy on Satellite Matters have acted as a catalyst in each of these
interwoven and important areas. First was the establishment of a new series
of technical documents on the operational use of R&D satellite data. Second
was a recognition of the importance of R&D satellite data in meeting WMO
observational data requirements and the subsequent development of a set of
Guidelines for requirements for observational data from operational and R&D
satellite missions. Third have been the responses by the R&D space agencies
in making commitments in support of the system design for the space-based
component of the Global Observing System. And lastly has been WMO’s
recognition that it should have a more appropriate programme structure - a
WMO Space Programme - to capitalize on the full potential of satellite data,
products and services from both the operational and R&D satellites.
WMO Members’ responses to the request for input for the report on the
utility of R&D satellite data and products covered the full spectrum of WMO
Regions as well as a good cross-section of developed and developing countries.
Countries from both the Northern and Southern Hemispheres, tropical, mid-
and high-latitude as well as those with coastlines and those landlocked had
responded. Most disciplines and application areas including NWP, hydrology,
climate, oceanography, agrometeorology, environmental monitoring and
detection and monitoring of natural disasters were included.
A number of WMO Programmes and associated application areas
supported by data and products from the R&D satellites. While not complete,
the list included specific applications within the disciplines of agrometeorology,
weather forecasting, hydrology, climate and oceanography including:
monitoring of ecology, sea-ice, snow cover, urban heat island, crop yield,
vegetation, flood, volcanic ash and other natural disasters; tropical cyclone
forecasting; fire areas; oceanic chlorophyll content; NWP; sea height; and CO2
exchange between the atmosphere and ocean.
WMO agreed that there was an increasing convergence between research
and operational requirements for the space-based component of the Global
Observing System and that WMO should seek to establish a continuum of
requirements for observational data from R&D satellite missions to operational
missions. WMO endorsed the Guidelines for requirements for observational data
from operational and R&D satellite missions to provide operational users a
measure of confidence in the availability of operational and R&D observational
data, and data providers with an indication of its utility.
25. M.V.K. Sivakumar and Donald E. Hinsman 19
The inclusion of R&D satellite systems into the space-based component
of GOS would more than double the need for external coordination
mechanisms. Firstly, there will be unique coordination needs between WMO
and R&D space agencies. Secondly, there will be coordination needs between
operational and R&D space agencies in such areas as frequency coordination,
orbit coordination including equator crossing-times, standardization of data
formats, standardization of user stations. Figure 5 shows the present space-
based sub-system of the Global Observing System with the new R&D
constellation including NASA’s Aqua, Terra, NPP, TRMM, QuikSCAT and
GPM missions, ESA’s ENVISAT, ERS-1 and ERS-2 missions, NASDA’s
ADEOS II and GCOM series, Rosaviakosmos’s research instruments on board
ROSHYDROMET’s operational METEOR 3M Nl satellite, as well as on its
future Ocean series and CNES’s JASON-1 and SPOT-5.
Figure 5: Space-based sub-system of the Global Observing System in 2003.
To better satisfy the needs of all WMO and supported programmes for
satellite data, products and services from both operational and R&D satellites
and in consideration of the increasing role of both types of satellites, WMO
felt it appropriate to propose an expansion of the present mechanisms for
26. 20 Satellite Remote Sensing and GIS Applications in Agricultural Meteorology
coordination within the WMO structure and cooperation between WMO and
the operators of operational meteorological satellites and R&D satellites. In
doing so, WMO felt that an effective means to improve cooperation with both
operational meteorological and R&D satellite operators would be through an
expanded CGMS that would include those R&D space agencies contributing
to the space-based component of the GOS.
WMO agreed that the WMO satellite activities had grown and that it
was now appropriate to establish a WMO Space Programme as a matter of
priority. The scope, goals and objectives of the new programme should respond
to the tremendous growth in the utilization of environmental satellite data,
products and services within the expanded space-based component of the GOS
that now include appropriate Research and Development environmental
satellite missions. The Consultative Meetings on High-Level Policy on Satellite
Matters should be institutionalized in order to more formally establish the
dialogue and participation of environmental satellite agencies in WMO matters.
In considering the important contributions made by environmental satellite
systems to WMO and its supported programmes as well as the large
expenditures by the space agencies, WMO felt it appropriate that the overall
responsibility for the new WMO Space Programme should be assigned to CBS
and a new institutionalized Consultative Meetings on High-Level Policy on
Satellite Matters.
CONCLUSIONS
Recent developments in remote sensing and GIS hold much promise to
enhance integrated management of all available information and the extraction
of desired information to promote sustainable agriculture and development.
Active promotion of the use of remote sensing and GIS in the National
Meteorological and Hydrological Services (NMHSs), could enhance improved
agrometeorological applications. To this end it is important to reinforce training
in these new fields. The promotion of new specialised software should make
the applications of the various devices easier, bearing in mind the possible
combination of several types of inputs such as data coming from standard
networks, radar and satellites, meteorological and climatological models, digital
cartography and crop models based on the scientific acquisition of the last
twenty years. International cooperation is crucial to promote the much needed
applications in the developing countries and the WMO Space Programme
actively promotes such cooperation throughout all WMO Programmes and
provides guidance to these and other multi-sponsored programmes on the
potential of remote sensing techniques in meteorology, hydrology and related
27. M.V.K. Sivakumar and Donald E. Hinsman 21
disciplines, as well as in their applications. The new WMO Space Programme
will further enhance both external and internal coordination necessary to
maximize the exploitation of the space-based component of the GOS to provide
valuable satellite data, products and services to WMO Members towards
meeting observational data requirements for WMO programmes more so than
ever before in the history of the World Weather Watch.
REFERENCES
Di Chiara, C. and G. Maracchi. 1994. Guide au S.I.S.P. ver. 1.0. Technical Manual No. 14,
CeSIA, Firenze, Italy.
Kleschenko, A.D. 1983. Use of remote sensing for obtaining agrometeorological information.
CAgM Report No. 12, Part I. Geneva, Switzerland: World Meteorological Organization.
Kanemasu, E.T. and I.D. Filcroft. 1992. Operational remote sensing systems in agriculture.
CAgM Report No. 50, Part I. Geneva, Switzerland: World Meteorological Organization.
Maracchi, G. 1991. Agrometeorologia : stato attuale e prospettive future. Proc. Congress
Agrometeorologia e Telerilevamento. Agronica, Palermo, Italy, pp. 1-5.
Maracchi, G., V. Pérarnaud and A.D. Kleschenko. 2000. Applications of geographical
information systems and remote sensing in agrometeorology. Agric. For. Meteorol.
103:119-136.
Romanelli, S., L. Bottai and F. Maselli. 1998. Studio preliminare per la stima del rischio
d’incendio boschivo a scala regionale per mezzo dei dati satellitari e ausilari. Tuscany
Region - Laboratory for Meteorology and Environmental Modelling (LaMMA), Firenze,
Italy.
Seguin, B. 1992. Satellite applications to agrometeorology: technological developments for
the period 1985-1989. CAgM Report No. 50, Part II. Geneva, Switzerland: World
Meteorological Organization.
Seitnazarov, 1999. Technology and methods of collection, distribution and analyzing of
agrometeorological data in Dashhovuz velajat, Turkmenistan. In: Contributions from
members on Operational Applications in the International Workshop on
Agrometeorology in the 21st
Century: Needs and Perspectives, Accra, Ghana. CAgM
Report No. 77, Geneva, Switzerland: World Meteorological Organization.
WMO. 1998. Preliminary statement of guidance regarding how well satellite capabilities
meet WMO user requirements in several application areas, SAT-21, WMO/TD No.
913, Geneva, Switzerland: World Meteorological Organization.
WMO. 2000. Statement of guidance regarding how well satellite capabilities meet wmo
user requirements in several application areas. SAT-22, WMO/TD No. 992, Geneva,
Switzerland: World Meteorological Organization.
28. PRINCIPLES OF REMOTE SENSING
Shefali Aggarwal
Photogrammetry and Remote Sensing Division
Indian Institute of Remote Sensing, Dehra Dun
Abstract : Remote sensing is a technique to observe the earth surface or the
atmosphere from out of space using satellites (space borne) or from the air using
aircrafts (airborne). Remote sensing uses a part or several parts of the
electromagnetic spectrum. It records the electromagnetic energy reflected or emitted
by the earth’s surface. The amount of radiation from an object (called radiance) is
influenced by both the properties of the object and the radiation hitting the object
(irradiance). The human eyes register the solar light reflected by these objects and
our brains interpret the colours, the grey tones and intensity variations. In remote
sensing various kinds of tools and devices are used to make electromagnetic radiation
outside this range from 400 to 700 nm visible to the human eye, especially the
near infrared, middle-infrared, thermal-infrared and microwaves.
Remote sensing imagery has many applications in mapping land-use and cover,
agriculture, soils mapping, forestry, city planning, archaeological investigations,
military observation, and geomorphological surveying, land cover changes,
deforestation, vegetation dynamics, water quality dynamics, urban growth, etc. This
paper starts with a brief historic overview of remote sensing and then explains the
various stages and the basic principles of remotely sensed data collection mechanism.
INTRODUCTION
Remote sensing (RS), also called earth observation, refers to obtaining
information about objects or areas at the Earth’s surface without being
in direct contact with the object or area. Humans accomplish this task with
aid of eyes or by the sense of smell or hearing; so, remote sensing is day-to-
day business for people. Reading the newspaper, watching cars driving in front
of you are all remote sensing activities. Most sensing devices record information
about an object by measuring an object’s transmission of electromagnetic energy
from reflecting and radiating surfaces.
Satellite Remote Sensing and GIS Applications in Agricultural Meteorology
pp. 23-38
29. 24 Principles of Remote Sensing
Remote sensing techniques allow taking images of the earth surface in
various wavelength region of the electromagnetic spectrum (EMS). One of the
major characteristics of a remotely sensed image is the wavelength region it
represents in the EMS. Some of the images represent reflected solar radiation
in the visible and the near infrared regions of the electromagnetic spectrum,
others are the measurements of the energy emitted by the earth surface itself
i.e. in the thermal infrared wavelength region. The energy measured in the
microwave region is the measure of relative return from the earth’s surface,
where the energy is transmitted from the vehicle itself. This is known as active
remote sensing, since the energy source is provided by the remote sensing
platform. Whereas the systems where the remote sensing measurements
depend upon the external energy source, such as sun are referred to as passive
remote sensing systems.
PRINCIPLES OF REMOTE SENSING
Detection and discrimination of objects or surface features means detecting
and recording of radiant energy reflected or emitted by objects or surface
material (Fig. 1). Different objects return different amount of energy in different
bands of the electromagnetic spectrum, incident upon it. This depends on
the property of material (structural, chemical, and physical), surface roughness,
angle of incidence, intensity, and wavelength of radiant energy.
The Remote Sensing is basically a multi-disciplinary science which includes
a combination of various disciplines such as optics, spectroscopy, photography,
computer, electronics and telecommunication, satellite launching etc. All these
technologies are integrated to act as one complete system in itself, known as
Remote Sensing System. There are a number of stages in a Remote Sensing
process, and each of them is important for successful operation.
Stages in Remote Sensing
• Emission of electromagnetic radiation, or EMR (sun/self- emission)
• Transmission of energy from the source to the surface of the earth, as well
as absorption and scattering
• Interaction of EMR with the earth’s surface: reflection and emission
• Transmission of energy from the surface to the remote sensor
• Sensor data output
30. Shefali Aggarwal 25
• Data transmission, processing and analysis
What we see
At temperature above absolute zero, all objects radiate electromagnetic
energy by virtue of their atomic and molecular oscillations. The total amount
of emitted radiation increases with the body’s absolute temperature and peaks
at progressively shorter wavelengths. The sun, being a major source of energy,
radiation and illumination, allows capturing reflected light with conventional
(and some not-so-conventional) cameras and films.
The basic strategy for sensing electromagnetic radiation is clear. Everything
in nature has its own unique distribution of reflected, emitted and absorbed
radiation. These spectral characteristics, if ingeniously exploited, can be used
to distinguish one thing from another or to obtain information about shape,
size and other physical and chemical properties.
Modern Remote Sensing Technology versus Conventional Aerial Photography
The use of different and extended portions of the electromagnetic
spectrum, development in sensor technology, different platforms for remote
sensing (spacecraft, in addition to aircraft), emphasize on the use of spectral
information as compared to spatial information, advancement in image
processing and enhancement techniques, and automated image analysis in
addition to manual interpretation are points for comparison of conventional
aerial photography with modern remote sensing system.
Figure 1: Remote Sensing process
Built-up Area
Sun
Distribute for Analysis
Pre-Process and Archive
Satellite
Reflected
Solar Radiation
F o r e s t Grass
Water
Bare Soil Paved
Road
Atmosphere
Down Link
31. 26 Principles of Remote Sensing
During early half of twentieth century, aerial photos were used in military
surveys and topographical mapping. Main advantage of aerial photos has been
the high spatial resolution with fine details and therefore they are still used
for mapping at large scale such as in route surveys, town planning,
construction project surveying, cadastral mapping etc. Modern remote sensing
system provide satellite images suitable for medium scale mapping used in
natural resources surveys and monitoring such as forestry, geology, watershed
management etc. However the future generation satellites are going to provide
much high-resolution images for more versatile applications.
HISTORIC OVERVIEW
In 1859 Gaspard Tournachon took an oblique photograph of a small village
near Paris from a balloon. With this picture the era of earth observation and
remote sensing had started. His example was soon followed by other people
all over the world. During the Civil War in the United States aerial
photography from balloons played an important role to reveal the defence
positions in Virginia (Colwell, 1983). Likewise other scientific and technical
developments this Civil War time in the United States speeded up the
development of photography, lenses and applied airborne use of this
technology. Table 1 shows a few important dates in the development of remote
sensing.
The next period of fast development took place in Europe and not in the
United States. It was during World War I that aero planes were used on a
large scale for photoreconnaissance. Aircraft proved to be more reliable and
more stable platforms for earth observation than balloons. In the period
between World War I and World War II a start was made with the civilian
use of aerial photos. Application fields of airborne photos included at that
time geology, forestry, agriculture and cartography. These developments lead
to much improved cameras, films and interpretation equipment. The most
important developments of aerial photography and photo interpretation took
place during World War II. During this time span the development of other
imaging systems such as near-infrared photography; thermal sensing and radar
took place. Near-infrared photography and thermal-infrared proved very
valuable to separate real vegetation from camouflage. The first successful
airborne imaging radar was not used for civilian purposes but proved valuable
for nighttime bombing. As such the system was called by the military ‘plan
position indicator’ and was developed in Great Britain in 1941.
32. Shefali Aggarwal 27
After the wars in the 1950s remote sensing systems continued to evolve
from the systems developed for the war effort. Colour infrared (CIR)
photography was found to be of great use for the plant sciences. In 1956
Colwell conducted experiments on the use of CIR for the classification and
recognition of vegetation types and the detection of diseased and damaged or
stressed vegetation. It was also in the 1950s that significant progress in radar
technology was achieved.
Table1: Milestones in the History of Remote Sensing
1800 Discovery of Infrared by Sir W. Herschel
1839 Beginning of Practice of Photography
1847 Infrared Spectrum Shown by J.B.L. Foucault
1859 Photography from Balloons
1873 Theory of Electromagnetic Spectrum by J.C. Maxwell
1909 Photography from Airplanes
1916 World War I: Aerial Reconnaissance
1935 Development of Radar in Germany
1940 WW II: Applications of Non-Visible Part of EMS
1950 Military Research and Development
1959 First Space Photograph of the Earth (Explorer-6)
1960 First TIROS Meteorological Satellite Launched
1970 Skylab Remote Sensing Observations from Space
1972 Launch Landsat-1 (ERTS-1) : MSS Sensor
1972 Rapid Advances in Digital Image Processing
1982 Launch of Landsat -4 : New Generation of Landsat Sensors: TM
1986 French Commercial Earth Observation Satellite SPOT
1986 Development Hyperspectral Sensors
1990 Development High Resolution Space borne Systems
First Commercial Developments in Remote Sensing
1998 Towards Cheap One-Goal Satellite Missions
1999 Launch EOS : NASA Earth Observing Mission
1999 Launch of IKONOS, very high spatial resolution sensor system
33. 28 Principles of Remote Sensing
ELECTROMAGNETIC RADIATION AND THE ELECTROMAGNETIC
SPECTRUM
EMR is a dynamic form of energy that propagates as wave motion at a velocity
of c = 3 x 1010
cm/sec. The parameters that characterize a wave motion are
wavelength (λ), frequency (ν) and velocity (c) (Fig. 2). The relationship
between the above is
c = νλ.
Figure 2: Electromagnetic wave. It has two components, Electric field E and Magnetic
field M, both perpendicular to the direction of propagation
Electromagnetic energy radiates in accordance with the basic wave theory.
This theory describes the EM energy as travelling in a harmonic sinusoidal
fashion at the velocity of light. Although many characteristics of EM energy
are easily described by wave theory, another theory known as particle theory
offers insight into how electromagnetic energy interacts with matter. It suggests
that EMR is composed of many discrete units called photons/quanta. The
energy of photon is
Q = hc / λ = h ν
Where
Q is the energy of quantum,
h = Planck’s constant
34. Shefali Aggarwal 29
This region is beyond the violet portion of the visible
wavelength, and hence its name. Some earth’s surface
material primarily rocks and minerals emit visible UV
radiation. However UV radiation is largely scattered
by earth’s atmosphere and hence not used in field of
remote sensing.
This is the light, which our eyes can detect. This is
the only portion of the spectrum that can be
associated with the concept of color. Blue Green and
Red are the three primary colors of the visible
spectrum.They are defined as such because no single
primary color can be created from the other two, but
all other colors can be formed by combining the
three in various proportions. The color of an object
is defined by the color of the light it reflects.
Wavelengths longer than the red portion of the
visible spectrum are designated as the infrared
spectrum. British Astronomer William Herschel
discovered this in 1800. The infrared region can be
divided into two categories based on their radiation
properties.
Reflected IR (.7 µm - 3.0 µm) is used for remote
sensing. Thermal IR (3 µm - 35 µm) is the radiation
emitted from earth’s surface in the form of heat and
used for remote sensing.
This is the longest wavelength used in remote sensing.
The shortest wavelengths in this range have
properties similar to thermal infrared region. The
main advantage of this spectrum is its ability to
penetrate through clouds.
This is the longest portion of the spectrum mostly
used for commercial broadcast and meteorology.
Table 2: Principal Divisions of the Electromagnetic Spectrum
Wavelength Description
Gamma rays Gamma rays
X-rays X-rays
Ultraviolet (UV) region
0.30 µm - 0.38 µm
(1µm = 10-6
m)
Visible Spectrum
0.4 µm - 0.7 µm
Violet 0.4 µm -0.446 µm
Blue 0.446 µm -0.5 µm
Green 0.5 µm - 0.578 µm
Yellow 0.578 µm - 0.592 µm
Orange 0.592 µm - 0.62 µm
Red 0.62 µm -0.7 µm
Infrared (IR) Spectrum
0.7 µm – 100 µm
Microwave Region
1 mm - 1 m
Radio Waves
(>1 m)
35. 30 Principles of Remote Sensing
Types of Remote Sensing
Remote sensing can be either passive or active. ACTIVE systems have their
own source of energy (such as RADAR) whereas the PASSIVE systems depend
upon external source of illumination (such as SUN) or self-emission for remote
sensing.
INTERACTION OF EMR WITH THE EARTH’S SURFACE
Radiation from the sun, when incident upon the earth’s surface, is either
reflected by the surface, transmitted into the surface or absorbed and emitted
by the surface (Fig. 3). The EMR, on interaction, experiences a number of
changes in magnitude, direction, wavelength, polarization and phase. These
changes are detected by the remote sensor and enable the interpreter to obtain
useful information about the object of interest. The remotely sensed data
contain both spatial information (size, shape and orientation) and spectral
information (tone, colour and spectral signature).
Figure 3: Interaction of Energy with the earth’s surface. ( source: Liliesand & Kiefer, 1993)
From the viewpoint of interaction mechanisms, with the object-visible and
infrared wavelengths from 0.3 µm to 16 µm can be divided into three regions.
The spectral band from 0.3 µm to 3 µm is known as the reflective region. In
this band, the radiation sensed by the sensor is that due to the sun, reflected
ER (λ) = Reflected energy
EI (λ) = ER(λ) + EA (λ) + ET (λ)
EI (λ) = Incident energy
EA(λ) = Absorbed energy ET(λ) = Transmitted energy
36. Shefali Aggarwal 31
Figure 4. Different types of scattering surfaces (a) Perfect specular reflector (b) Near perfect
specular reflector (c) Lambertain (d) Quasi-Lambertian (e) Complex.
by the earth’s surface. The band corresponding to the atmospheric window
between 8 µm and 14 µm is known as the thermal infrared band. The energy
available in this band for remote sensing is due to thermal emission from the
earth’s surface. Both reflection and self-emission are important in the
intermediate band from 3 µm to 5.5 µm.
In the microwave region of the spectrum, the sensor is radar, which is an
active sensor, as it provides its own source of EMR. The EMR produced by
the radar is transmitted to the earth’s surface and the EMR reflected (back
scattered) from the surface is recorded and analyzed. The microwave region
can also be monitored with passive sensors, called microwave radiometers, which
record the radiation emitted by the terrain in the microwave region.
Reflection
Of all the interactions in the reflective region, surface reflections are the
most useful and revealing in remote sensing applications. Reflection occurs
when a ray of light is redirected as it strikes a non-transparent surface. The
reflection intensity depends on the surface refractive index, absorption
coefficient and the angles of incidence and reflection (Fig. 4).
Transmission
Transmission of radiation occurs when radiation passes through a
substance without significant attenuation. For a given thickness, or depth of
a substance, the ability of a medium to transmit energy is measured as
transmittance (τ).
37. 32 Principles of Remote Sensing
Transmitted radiation
τ =———————————
Incident radiation
Spectral Signature
Spectral reflectance, [ρ(λ)], is the ratio of reflected energy to incident
energy as a function of wavelength. Various materials of the earth’s surface have
different spectral reflectance characteristics. Spectral reflectance is responsible
for the color or tone in a photographic image of an object. Trees appear green
because they reflect more of the green wavelength. The values of the spectral
reflectance of objects averaged over different, well-defined wavelength intervals
comprise the spectral signature of the objects or features by which they can
be distinguished. To obtain the necessary ground truth for the interpretation
of multispectral imagery, the spectral characteristics of various natural objects
have been extensively measured and recorded.
The spectral reflectance is dependent on wavelength, it has different values
at different wavelengths for a given terrain feature. The reflectance
characteristics of the earth’s surface features are expressed by spectral reflectance,
which is given by:
ρ(λ) = [ER
(λ) / EI
(λ)] x 100
Where,
ρ(λ) = Spectral reflectance (reflectivity) at a particular wavelength.
ER
(λ) = Energy of wavelength reflected from object
EI
(λ) = Energy of wavelength incident upon the object
The plot between ρ(λ) and λ is called a spectral reflectance curve. This
varies with the variation in the chemical composition and physical conditions
of the feature, which results in a range of values. The spectral response patterns
are averaged to get a generalized form, which is called generalized spectral
response pattern for the object concerned. Spectral signature is a term used
for unique spectral response pattern, which is characteristic of a terrain feature.
Figure 5 shows a typical reflectance curves for three basic types of earth surface
features, healthy vegetation, dry bare soil (grey-brown and loamy) and clear
lake water.
38. Shefali Aggarwal 33
Reflectance Characteristics of Earth’s Cover types
The spectral characteristics of the three main earth surface features are
discussed below :
Vegetation: The spectral characteristics of vegetation vary with wavelength.
Plant pigment in leaves called chlorophyll strongly absorbs radiation in the
red and blue wavelengths but reflects green wavelength. The internal structure
of healthy leaves acts as diffuse reflector of near infrared wavelengths.
Measuring and monitoring the near infrared reflectance is one way that
scientists determine how healthy particular vegetation may be.
Water: Majority of the radiation incident upon water is not reflected but is
either absorbed or transmitted. Longer visible wavelengths and near infrared
radiation is absorbed more by water than by the visible wavelengths. Thus
water looks blue or blue green due to stronger reflectance at these shorter
wavelengths and darker if viewed at red or near infrared wavelengths. The
factors that affect the variability in reflectance of a water body are depth of
water, materials within water and surface roughness of water.
Soil: The majority of radiation incident on a soil surface is either reflected or
absorbed and little is transmitted. The characteristics of soil that determine
Figure 5. Typical Spectral Reflectance curves for vegetation, soil and water
Vegetation
Dry soil
(5% water)
Wet soil
(20% water)
Clear lake water
Turbid river water
0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4
Wavelength (micrometers)
SPOT XS Multispectral Bands
Landsat TM Bands
5 7
1 2 3
1 2 3 4
60
40
20
0
Middle Infrared
Reflected Infrared
Reflectance
(%)
39. 34 Principles of Remote Sensing
its reflectance properties are its moisture content, organic matter content,
texture, structure and iron oxide content. The soil curve shows less peak and
valley variations. The presence of moisture in soil decreases its reflectance.
By measuring the energy that is reflected by targets on earth’s surface over
a variety of different wavelengths, we can build up a spectral signature for
that object. And by comparing the response pattern of different features we
may be able to distinguish between them, which we may not be able to do if
we only compare them at one wavelength. For example, Water and Vegetation
reflect somewhat similarly in the visible wavelength but not in the infrared.
INTERACTIONS WITH THE ATMOSPHERE
The sun is the source of radiation, and electromagnetic radiation (EMR)
from the sun that is reflected by the earth and detected by the satellite or
aircraft-borne sensor must pass through the atmosphere twice, once on its
journey from the sun to the earth and second after being reflected by the
surface of the earth back to the sensor. Interactions of the direct solar radiation
and reflected radiation from the target with the atmospheric constituents
interfere with the process of remote sensing and are called as “Atmospheric
Effects”.
The interaction of EMR with the atmosphere is important to remote
sensing for two main reasons. First, information carried by EMR reflected/
emitted by the earth’s surface is modified while traversing through the
atmosphere. Second, the interaction of EMR with the atmosphere can be used
to obtain useful information about the atmosphere itself.
The atmospheric constituents scatter and absorb the radiation modulating
the radiation reflected from the target by attenuating it, changing its spatial
distribution and introducing into field of view radiation from sunlight
scattered in the atmosphere and some of the energy reflected from nearby
ground area. Both scattering and absorption vary in their effect from one part
of the spectrum to the other.
The solar energy is subjected to modification by several physical processes
as it passes the atmosphere, viz.
1) Scattering; 2) Absorption, and 3) Refraction
40. Shefali Aggarwal 35
Atmospheric Scattering
Scattering is the redirection of EMR by particles suspended in the
atmosphere or by large molecules of atmospheric gases. Scattering not only
reduces the image contrast but also changes the spectral signature of ground
objects as seen by the sensor. The amount of scattering depends upon the
size of the particles, their abundance, the wavelength of radiation, depth of
the atmosphere through which the energy is traveling and the concentration
of the particles. The concentration of particulate matter varies both in time
and over season. Thus the effects of scattering will be uneven spatially and
will vary from time to time.
Theoretically scattering can be divided into three categories depending
upon the wavelength of radiation being scattered and the size of the particles
causing the scattering. The three different types of scattering from particles
of different sizes are summarized below:
Scattering Wavelength Approximate Kinds
process dependence of particles
particle size
Selective
z Rayleigh λ -4 < 1 µm Air molecules
z Mie λo to λ-4 0.1 to 10 µm Smoke, haze
z Non-selective λo > 10 µm Dust, fog, clouds
Rayleigh Scattering
Rayleigh scattering predominates where electromagnetic radiation interacts
with particles that are smaller than the wavelength of the incoming light. The
effect of the Rayleigh scattering is inversely proportional to the fourth power
of the wavelength. Shorter wavelengths are scattered more than longer
wavelengths. In the absence of these particles and scattering the sky would
appear black. In the context of remote sensing, the Rayleigh scattering is the
most important type of scattering. It causes a distortion of spectral
characteristics of the reflected light when compared to measurements taken
on the ground.
41. 36 Principles of Remote Sensing
Mie Scattering
Mie scattering occurs when the wavelength of the incoming radiation is
similar in size to the atmospheric particles. These are caused by aerosols: a
mixture of gases, water vapor and dust. It is generally restricted to the lower
atmosphere where the larger particles are abundant and dominates under
overcast cloud conditions. It influences the entire spectral region from ultra
violet to near infrared regions.
Non-selective Scattering
This type of scattering occurs when the particle size is much larger than
the wavelength of the incoming radiation. Particles responsible for this effect
are water droplets and larger dust particles. The scattering is independent of
the wavelength, all the wavelength are scattered equally. The most common
example of non-selective scattering is the appearance of clouds as white. As
cloud consist of water droplet particles and the wavelengths are scattered in
equal amount, the cloud appears as white.
Occurrence of this scattering mechanism gives a clue to the existence of
large particulate matter in the atmosphere above the scene of interest which
itself is a useful data. Using minus blue filters can eliminate the effects of the
Rayleigh component of scattering. However, the effect of heavy haze i.e. when
all the wavelengths are scattered uniformly, cannot be eliminated using haze
filters. The effects of haze are less pronounced in the thermal infrared region.
Microwave radiation is completely immune to haze and can even penetrate
clouds.
Atmospheric Absorption
The gas molecules present in the atmosphere strongly absorb the EMR
passing through the atmosphere in certain spectral bands. Mainly three gases
are responsible for most of absorption of solar radiation, viz. ozone, carbon
dioxide and water vapour. Ozone absorbs the high energy, short wavelength
portions of the ultraviolet spectrum (λ < 0.24 µm) thereby preventing the
transmission of this radiation to the lower atmosphere. Carbon dioxide is
important in remote sensing as it effectively absorbs the radiation in mid and
far infrared regions of the spectrum. It strongly absorbs in the region from
about 13-17.5 µm, whereas two most important regions of water vapour
absorption are in bands 5.5 - 7.0 µm and above 27 µm. Absorption relatively
42. Shefali Aggarwal 37
reduces the amount of light that reaches our eye making the scene look
relatively duller.
Atmospheric Windows
The general atmospheric transmittance across the whole spectrum of
wavelengths is shown in Figure 6. The atmosphere selectively transmits energy
of certain wavelengths. The spectral bands for which the atmosphere is
relatively transparent are known as atmospheric windows. Atmospheric
windows are present in the visible part (.4 µm - .76 µm) and the infrared
regions of the EM spectrum. In the visible part transmission is mainly effected
by ozone absorption and by molecular scattering. The atmosphere is transparent
again beyond about λ= 1mm, the region used for microwave remote sensing.
Figure 6 : Atmospheric windows
Refraction
The phenomenon of refraction, that is bending of light at the contact
between two media, also occurs in the atmosphere as the light passes through
the atmospheric layers of varied clarity, humidity and temperature. These
variations influence the density of atmospheric layers, which in turn, causes
the bending of light rays as they pass from one layer to another. The most
common phenomena are the mirage like apparitions sometimes visible in the
distance on hot summer days.
CONCLUSIONS
Remote sensing technology has developed from balloon photography to
aerial photography to multi-spectral satellite imaging. Radiation interaction
characteristics of earth and atmosphere in different regions of electromagnetic
blocking effect of atmosphere
atmospheric
transmittance
1.0
0.0
microwaves
0.3 0.6 1.0 5.0 10 50 100 200 m 1mm 1cm 1m 10m
Wavelength
UV
VIS
IIIR
VIIR
TIR
IIR
VIIR
43. 38 Principles of Remote Sensing
spectrum are very useful for identifying and characterizing earth and
atmospheric features.
REFERENCES
Campbell, J.B. 1996. Introduction to Remote Sensing. Taylor & Francis, London.
Colwell, R.N. (Ed.) 1983. Manual of Remote Sensing. Second Edition. Vol I: Theory,
Instruments andTechniques. American Society of Photogrammetry and Remote Sensing
ASPRS, Falls Church.
Curran, P.J. 1985. Principles of Remote Sensing. Longman Group Limited, London.
Elachi, C. 1987. Introduction to the Physics and Techniques of Remote Sensing. Wiley Series
in Remote Sensing, New York.
http://www.ccrs.nrcan.gc.ca/ccrs/learn/tutorials/fundam/chapter1/chapter1_1_e.html
Joseph, G. 1996. Imaging Sensors. Remote Sensing Reviews, 13: 257-342.
Lillesand, T.M. and Kiefer, R.1993. Remote Sensing and Image Interpretation. Third Edition
John Villey, New York.
Manual of Remote Sensing. IIIrd
Edition. American Society of Photogrammtery and Remote
Sensing.
Sabins, F.F. 1997. Remote Sensing and Principles and Image Interpretation. WH Freeman,
New York.
44. EARTH RESOURCE SATELLITES
Shefali Aggarwal
Photogrammetry and Remote Sensing Division
Indian Institute of Remote Sensing, Dehra Dun
Abstract : Since the first balloon flight, the possibilities to view the earth’s surface
from above had opened up new vistas of opportunities for mankind. The view from
above has inspired a number of technological developments that offer a wide-range
of techniques to observe the phenomena on the earth’s surface, under oceans, and
underneath the surface of the earth. While the first imagery used for remote sensing
came from balloons and later from airplanes, today the satellites or spacecraft are
widely used for data collection. The uniqueness of satellite remote sensing lies in
its ability to provide a synoptic view of the earth’s surface and to detect features at
electromagnetic wavelengths, which are not visible to the human eye. Data from
satellite images can show larger areas than aerial survey data and, as a satellite
regularly passes over the same area capturing new data each time, changes in the
land use /land cover can be periodically monitored.
In order to use remotely sensed data, the user has to understand the characteristics
of the system being used. The most important system characteristic the user has to
understand is resolution. Resolution is measured in four ways, spatial, spectral,
radiometric and temporal. The article describes the characteristics of satellite orbits
and sensor systems, data capturing mechanisms and then highlights some of the
commercially available satellites and future missions to be undertaken.
INTRODUCTION
Remote sensing is defined as the science which deals with obtaining
information about objects on earth surface by analysis of data, received
from a remote platform. Since the launch of the first remote sensing weather
satellite (TIROS-1) in 1960 and the first Earth resources satellite in 1972
(Landsat-1), various platforms with a variety of remote sensing sensors have
been launched to study the Earth land cover, the oceans, the atmosphere or
to monitor the weather.
Satellite Remote Sensing and GIS Applications in Agricultural Meteorology
pp. 39-65
45. 40 Earth Resource Satellites
In the present context, information flows from an object to a receiver
(sensor) in the form of radiation transmitted through the atmosphere. The
interaction between the radiation and the object of interest conveys information
required on the nature of the object. In order for a sensor to collect and record
energy reflected or emitted from a target or surface, it must reside on a stable
platform away from the target or surface being observed. Important properties
of sensor system are the number of spectral bands, the spectral position of
these bands, the spatial resolution or pixel size and the orbit of the satellite.
Two satellite orbits are important for remote sensing observation of the
Earth: the geo-stationary orbit and the polar orbit. The geo-stationary orbit
is such a position for a satellite that it keeps pace with the rotation of the
Earth. These platforms are covering the same place and give continuous near
hemispheric coverage over the same area day and night. These satellites are
put in equatorial plane orbiting from west to east. Its coverage is limited to
70oN to 70oS latitudes and one satellite can view one-third globe (Figure 1).
As a result it is continuously located above the same geographical position.
These are mainly used for communication and meteorological applications.
Weather satellites such as Meteosat, MSG and GOES are normally positioned
in this orbit. It enables the sensor aboard the satellite to take every 30 minutes
a picture of the weather conditions over the same locations. This geo-stationary
orbit is located at an altitude of 36,000 km above the equator.
The following are the major geo-stationary satellites:
Satellite program Current Satellite Country Operational Agency
Launch Agency
METEOSAT METEOSAT-7 International EUMETSAT ESA
INDOEX METEOSAT-5 International EUMETSAT ESA
GOMS GOMS-1 Russia
(ELEKTRO)
INSAT INSAT Series India
Feng-Yun* Feng-Yun-2B China
GMS GMS-5 Japan
GOES (WEST) GOES-10 U.S.A. NOAA NASA
GOES (EAST) GOES-8 U.S.A. NOAA NASA
* Failed mission
46. Shefali Aggarwal 41
The second important remote sensing orbit is the polar orbit. Satellites
in a polar orbit, cycle the Earth from North Pole to South Pole. The polar
orbits have an inclination of approximately 99 degrees with the equator to
maintain a sun synchronous overpass i.e. the satellite passes over all places on
earth having the same latitude twice in each orbit at the same local sun-time.
This ensures similar illumination conditions when acquiring images over a
particular area over a series of days (Figure 2). Image acquisition mostly takes
place in the morning when the sun position is optimal between 9.30 and
11.00 hr local time. The altitude of the polar orbits varies from approximately
650 to 900 km although spy-satellites are in a much lower orbit.
Figure 2. Near Polar Orbits (source CCRS website)
Figure 1. Geo-stationary Orbit (source CCRS website)
As the satellite orbits the Earth from pole to pole, its east-west position
would not change if the Earth did not rotate. However, as seen from the
Earth, it seems that the satellite is shifting westward because the Earth is
rotating (from west to east) beneath it. This apparent movement allows the
Satellite
Ground Track
Equator
Earth’s Rotation
Satellite Direction
47. 42 Earth Resource Satellites
satellite swath to cover a new area with each pass (Figure 3). The satellite’s
orbit and the rotation of the Earth work together to allow complete coverage
of the Earth’s surface, after it has completed one complete cycle of orbits (Figure
4). Through these satellites the entire globe is covered on regular basis and
gives repetitive coverage on periodic basis. All the remote sensing earth resource
satellites may be grouped in this category. Few of these satellites are LANDSAT
series, SPOT series, IRS series, NOAA, SEASAT, TIROS, HCMM, SKYLAB,
SPACE SHUTTLE etc.
Figure 3. Area Coverage on each Consecutive pass (source: CCRS website)
Figure 4. Complete Coverage of Earth Surface by Sun Synchronous Satellites
48. Shefali Aggarwal 43
REMOTE SENSING SENSORS
Sensor is a device that gathers energy (EMR or other), converts it into a
signal and presents it in a form suitable for obtaining information about the
target under investigation. These may be active or passive depending on the
source of energy.
Sensors used for remote sensing can be broadly classified as those operating
in Optical-Infrared (OIR) region and those operating in the microwave region.
OIR and microwave sensors can further be subdivided into passive and active.
Active sensors use their own source of energy. Earth surface is illuminated
through energy emitted by its own source, a part of it is reflected by the surface
in the direction of the sensor, which is received to gather the information.
Passive sensors receive solar electromagnetic energy reflected from the surface
or energy emitted by the surface itself. These sensors do not have their own
source of energy and can not be used at nighttime, except thermal sensors.
Again, sensors (active or passive) could either be imaging, like camera or sensor,
which acquire images of the area and non-imaging types like non-scanning
radiometer or atmospheric sounders.
Resolution
Resolution is defined as the ability of the system to render the information
at the smallest discretely separable quantity in terms of distance (spatial),
wavelength band of EMR (spectral), time (temporal) and/or radiation quantity
(radiometric).
Spatial Resolution
Spatial resolution is the projection of a detector element or a slit onto the
ground. In other words, scanner’s spatial resolution is the ground segment
sensed at any instant. It is also called ground resolution element (GRE).
The spatial resolution at which data are acquired has two effects – the
ability to identify various features and quantify their extent. The former one
relates to the classification accuracy and the later to the ability to accurately
make mensuration. Images where only large features are visible are said to have
coarse or low resolution. In fine resolution images, small objects can be detected.
49. 44 Earth Resource Satellites
Spectral Resolution
Spectral emissivity curves characterize the reflectance and/or emittance of
a feature or target over a variety of wavelengths. Different classes of features
and details in an image can be distinguished by comparing their responses
over distinct wavelength ranges. Broad classes such as water and vegetation
can be separated using broad wavelength ranges (VIS, NIR), whereas specific
classes like rock types would require a comparison of fine wavelength ranges
to separate them. Hence spectral resolution describes the ability of the sensor
to define fine wavelength intervals i.e. sampling the spatially segmented image
in different spectral intervals, thereby allowing the spectral irradiance of the
image to be determined.
Radiometric Resolution
This is a measure of the sensor to differentiate the smallest change in the
spectral reflectance/emittance between various targets. The radiometric
resolution depends on the saturation radiance and the number of quantisation
levels. Thus, a sensor whose saturation is set at 100% reflectance with an 8
bit resolution will have a poor radiometric sensitivity compared to a sensor
whose saturation radiance is set at 20% reflectance and 7 bit digitization.
Temporal Resolution
Obtaining spatial and spectral data at certain time intervals. Temporal
resolution is also called as the repetivity of the satellite; it is the capability of
the satellite to image the exact same area at the same viewing angle at different
periods of time. The temporal resolution of a sensor depends on a variety of
factors, including the satellite/sensor capabilities, the swath overlap and
latitude.
Multispectral Scanning Principle
Cameras and their use for aerial photography are the simplest and oldest
of sensors used for remote sensing of the Earth’s surface. Cameras are framing
systems (Figure 5a), which acquire a near-instantaneous “snapshot” of an area
of the Earth’s surface. Camera systems are passive optical sensors that use a
lens (or system of lenses collectively referred to as the optics) to form an image
at the focal plane, the “aerial image plane” at which an image is sharply
defined.
50. Shefali Aggarwal 45
Many electronic (as opposed to photographic) remote sensors acquire data
using scanning systems, which employ a sensor with a narrow field of view
that sweeps over the terrain to build up and produce a two-dimensional image
of the surface. Scanning systems can be used on both aircraft and satellite
platforms and have essentially the same operating principles. A scanning system
used to collect data over a variety of different wavelength ranges is called a
multispectral scanner (MSS), and is the most commonly used scanning system.
There are two main modes or methods of scanning employed to acquire
multispectral image data - across-track scanning, and along-track scanning.
Across-track scanners scan the Earth in a series of lines (Figure 5b). The
lines are oriented perpendicular to the direction of motion of the sensor
platform (i.e. across the swath). Each line is scanned from one side of the sensor
to the other, using a rotating mirror. As the platform moves forward over the
Earth, successive scans build up a two-dimensional image of the Earth’s surface.
So, the Earth is scanned point by point and line after line. These systems are
referred to as whiskbroom scanners. The incoming reflected or emitted radiation
is separated into several spectral components that are detected independently.
A bank of internal detectors, each sensitive to a specific range of wavelengths,
detects and measures the energy for each spectral band and then, as an
electrical signal, they are converted to digital data and recorded for subsequent
computer processing.
Figure 5. Principle of imaging sensor systems; (a) framing system, (b) whiskbroom scanner,
(c) pushbroom scanner. (source :http://cgi.girs.wageningen-ur.nl/igi-new)
51. 46 Earth Resource Satellites
Along-track scanners also use the forward motion of the platform to record
successive scan lines and build up a two-dimensional image, perpendicular to
the flight direction (Figure 5c). However, instead of a scanning mirror, they
use a linear array of detectors (so-called charge-coupled devices, CCDs) located
at the focal plane of the image formed by lens systems, which are “pushed”
along in the flight track direction (i.e. along track). These systems are also
referred to as push broom scanners, as the motion of the detector array is
analogous to a broom being pushed along a floor. A separate linear array is
required to measure each spectral band or channel. For each scan line, the
energy detected by each detector of each linear array is sampled electronically
and digitally recorded.
Regardless of whether the scanning system used is either of these two types,
it has several advantages over photographic systems. The spectral range of
photographic systems is restricted to the visible and near-infrared regions while
MSS systems can extend this range into the thermal infrared. They are also
capable of much higher spectral resolution than photographic systems. Multi-
band or multispectral photographic systems use separate lens systems to
acquire each spectral band. This may cause problems in ensuring that the
different bands are comparable both spatially and radiometrically and with
registration of the multiple images. MSS systems acquire all spectral bands
simultaneously through the same optical system to alleviate these problems.
Photographic systems record the energy detected by means of a photochemical
process which is difficult to measure and to make consistent. Because MSS
data are recorded electronically, it is easier to determine the specific amount
of energy measured, and they can record over a greater range of values in a
digital format. Photographic systems require a continuous supply of film and
processing on the ground after the photos have been taken. The digital
recording in MSS systems facilitates transmission of data to receiving stations
on the ground and immediate processing of data in a computer environment.
Thermal Scanner
Many multispectral (MSS) systems sense radiation in the thermal infrared
as well as the visible and reflected infrared portions of the spectrum. However,
remote sensing of energy emitted from the Earth’s surface in the thermal
infrared (3 µm to 15 µm) is different from the sensing of reflected energy.
Thermal sensors use photo detectors sensitive to the direct contact of photons
on their surface, to detect emitted thermal radiation. The detectors are cooled
to temperatures close to absolute zero in order to limit their own thermal
52. Shefali Aggarwal 47
emissions. Thermal sensors essentially measure the surface temperature and
thermal properties of targets.
Thermal Imagers are typically across-track scanners that detect emitted
radiation in only the thermal portion of the spectrum. Thermal sensors employ
one or more internal temperature references for comparison with the detected
radiation, so they can be related to absolute radiant temperature. The data
are generally recorded on film and/or magnetic tape and the temperature
resolution of current sensors can reach 0.1 °C. For analysis, an image of relative
radiant temperatures is depicted in grey levels, with warmer temperatures
shown in light tones, and cooler temperatures in dark tones.
Table 1. Thermal Sensors
HCMM TM
Operational period 1978-1980 1982 to present
Orbital altitude 620 mm 705 km
Image coverage 700 by 700 km 185 by 170 km
Acquisition time, day 1:30 p.m. 10:30 a.m.
Acquisition time, night 2:30 a.m. 9:30 p.m.
Visible and reflected IR detectors
Number of bands 1 6
Spectral range 0.5 0 - 1.1 µm 0.4 - 2.35 µm
Ground resolution cell 500 by 500 m 30 by 30 m
Thermal IR detector
Spectral range 10.5 - 12.5 µm 10.5 - 12.5 µm
Ground resolution cell 600 by 600 m 120 by 120m
60 m by 60 m in Landsat 7
Microwave Sensing (RADAR)
Microwave data can be obtained by both active and passive systems. Passive
system monitor natural radiation at a particular frequency or range of
frequency. Data may be presented numerically as line trace data or as imagery.
Active systems (like SLAR and SAR) transmit their own energy and monitor
the returned signal.
53. 48 Earth Resource Satellites
Characteristics of such radar imagery both in SAR and SLAR and their
resolution depends on various parameters like frequency of the signal, look
direction, slant range, dielectric constant of the objects, phase, antenna length
etc. Spatial resolution in range and azimuth direction varies in different
manners.
RADAR (SAR) imageries have been obtained from satellite SEASAT, ERS
and space shuttle missions SIR-A, SIR-B and SIR-C using synthatic aperture
radar, which have all weather capability. Such data products are useful for
studies in cloud-covered region of the earth and in oceanography.
Table 2. Microwave Sensors
Seasat SIR-C/X- ESA RADARSAT ENVISAT JERS-1
SAR SAR SAR SAR ASAR
Frequency 1.275 GHz 5.3 GHz 5.3 5.33 GHz 5.33 GHz 1.275
1.275 GHz GHz GHz
Wave L band X band 3 cm C band C band L Band
length 23 cm C band 6 cm C band (23 cm)
L band 23 cm
Swath 100 km, 15 to 90 km 100 km 45-510 5 km – 75 km
Width centered Depend on km 100 km
20o
off orientation Varies Varies
nadir is antenna
Ground 25 x 25 m 10 to 200 m 30 m 100x100 m 30 m
Resolution to 9x9 m Varies
Varies
LAND OBSERVATION SATELLITES
Today more than ten earth observation satellites provide imagery that can
be used in various applications (Table-3). The list also includes some failed
as well as future missions. Agencies responsible for the distribution and trading
of data internationally are also listed.
Landsat Series of Satellites
NASA, with the co-operation of the U.S. Department of Interior, began
a conceptual study of the feasibility of a series of Earth Resources Technology
Satellites (ERTS). ERTS-1 was launched in July 23, 1972, and it operated
54. Shefali Aggarwal 49
until January 6, 1978. It represented the first unmanned satellite specifically
designed to acquire data about earth resources on a systematic, repetitive,
medium resolution, multispectral basis. It was primarily designed as an
experimental system to test the feasibility of collecting earth resources data
from unmanned satellites. About 300 individual ERTS-1 experiments were
conducted in 43 US states and 36 nations. Just prior to the launch of ERTS-
B on January 22nd 1975, NASA officially renamed the ERTS programme as
the “LANDSAT” programme. All subsequent satellites in the series carried
the Landsat designation. So far six Landsat satellites have been launched
successfully, while Landsat-6 suffered launch failure. Table-4 highlights the
characteristics of the Landsat series satellites. There have been four different
types of sensors included in various combinations on these missions. These
are Return Beam Vidicon camera (RBV) systems, Multispectral Scanner (MSS)
systems, Thematic Mapper (TM) and Enhanced Thematic Mapper (ETM).
After more than two decades of success, the Landsat program realised its
first unsuccessful mission with the launch failure of Landsat-6 on October 5,
1993. The sensor included on-board was the Enhanced Thematic Mapper
(ETM). To provide continuity with Landsat -4 and -5 the ETM incorporated
the same seven spectral bands and the same spatial resolutions as the TM.
The ETM’s major improvement over the TM was addition of an eighth
panchromatic band operating in 0.50 to 0.90-µm range and spatial resolution
of 15m. Landsat-7 includes two sensors: the Enhanced Thematic Mapper plus
(ETM+) and the High Resolution Multispectral Stereo Imager (HRMSI).
Spot Series of Satellite
French Government in joint programme with Sweden and Belgium
undertook the development of Systeme Pour l’Observation de la Terre (SPOT)
program. Conceived and designed by the French Center National d’Etudes
Spatiales (CNES), SPOT has developed into a large-scale international
programme with ground receiving stations and data distribution outlets located
in more than 30 countries. It is also the first system to have pointable optics.
This enables side-to-side off-nadir viewing capabilities, and it affords full scene
stereoscopic imaging from two different satellite tracks permitting coverage
of the same area. SPOT-1 was retired from full-time services on December
31, 1990. The SPOT-2 satellite was launched on January 21, 1990, and
SPOT-3 was launched on September 25, 1993. SPOT-4 was launched on
26 March, 1998. Characteristics of SPOT Satellites are presented in Table 5.
55. 50 Earth Resource Satellites
Table
3.
Operational
Earth
Observation
Satellites
EUROPE
MIDDLE
NORTH
AMERICA
ASIA
EAST
France
ESA
Israel
USA
Canada
India
Japan
SPOT1-1986
LANDSAT5
10m
-85,
30m
SPOT2-90
ERS1-92/00
LANDSAT6-
10m
Radar
93
SPOT3-93/96
ERS2-95
EARLYBIRD
IKONOS1-
RADARSAT-
IRS1C-95
Radar
-98
99,
1m
95
6m
SPOT4-98
ENVISAT-
LANDSAT7-
IKONOS2
IRS1D-97
10m
2001Radar
99,
15m
-99,
1m
6m
EROS
A/
QUICKBIRD-
ORBVIEW-
1-00
2m
01,
0.6m
01,
1m
SPOT5-02
EROS
B/
ORBVIEW
RADARSAT
IRS-P6-03,
ALOS-
3m+
HRS10
1-02,
1m
-02,
1m
-03
6MMSS
03,
2.5m
Distribution
SPOT
Miscellaneous
Imagesat
SI-EOSAT,
Earthwatch,
RADARSAT
NRSA-
JSI
IMAGING
Orbimage,
USGS
EOSAT