This document summarizes a study on scour around spur dikes in sand-gravel mixtures. The study found that maximum scour depth increases with factors like critical velocity ratio, water depth to armour particle ratio, and Froude number, but decreases with armour particle to spur dike length ratio. Scour depth is more influenced by sediment mixture properties, increasing with less uniformity. A non-linear equation is proposed to estimate maximum scour depth within 15% error. Sensitivity analysis found scour depth most depends on Froude number, followed by other parameters like armour particle to spur dike length ratio and water depth ratios.
Experimental Study on the Settling Velocity of
Coastal Mud in Quiescent Water: The Case of
Huangmaohai Estuary, South China Sea by Dong XU in Examines in Marine Biology and Oceanography: Open Access
Experimental study on effect of slot level on local scour around bridge piereSAT Journals
Abstract Many bridges in the world every year for Failure to consider in the design of hydraulic elements are destroyed. During the spring floods of 1987, 17 bridges in New York and New England were damaged or destroyed by scour. In 1985, 73 bridges were destroyed by floods in Pennsylvania, Virginia, and West Virginia. In the present study investigate effect application a slot , height “D” , width” D/4”in a circular pier ,where “D” is diameter of bridge pier and the size of 6 centimeters under 3 different discharges (values 35 , 40 , 45 Liter per second) and 4 different location of slot in a flume ,length 14 meters ,height 60 and width 60 centimeters. The experimental results show when height of slot is below the stream bed as D, scour depth will be reduced about 20.34% to 39.73% in front of the pier and scour volume approximately 46.84% to 75.74% Keywords: Bridge pier, Slot, Scour, scour depth, scour volume
This study presents a laboratory experiments for evaluating the local scour depth
around S-shape solid non- submerged groynes using different number of these groynes
and also different distances between them as two countermeasures to reduce the
scour. The study was conducted in non- curved laboratory flume where uniform
cohesion-less sand of median size (d50) equal to (0.7 mm) was used as the bed
material. The physical hydraulic model of the groynes was made of polystyrene foam
with fixed dimensions to operate under steady subcritical flow and clear water
conditions. The studied parameters in this study were the number of groynes changed
three times (single, double, triple), the distances between them altered also three times
(1L, 1.5 L, 2L) and finally the hydraulic conditions (depth and velocity of the mean
flow) also changed four times for each parameter. A new empirical equation was
derived where its coefficient of determination indicates good agreement between the
predicted results and the observed ones experimentally.
Fundamentals of fluid flow, Darcy's law, Unsaturated Condition, Reynolds Number, Poiseuille’s Flow, Laplace Law, The one-dimensional vertical flow of water
Experimental Study on the Settling Velocity of
Coastal Mud in Quiescent Water: The Case of
Huangmaohai Estuary, South China Sea by Dong XU in Examines in Marine Biology and Oceanography: Open Access
Experimental study on effect of slot level on local scour around bridge piereSAT Journals
Abstract Many bridges in the world every year for Failure to consider in the design of hydraulic elements are destroyed. During the spring floods of 1987, 17 bridges in New York and New England were damaged or destroyed by scour. In 1985, 73 bridges were destroyed by floods in Pennsylvania, Virginia, and West Virginia. In the present study investigate effect application a slot , height “D” , width” D/4”in a circular pier ,where “D” is diameter of bridge pier and the size of 6 centimeters under 3 different discharges (values 35 , 40 , 45 Liter per second) and 4 different location of slot in a flume ,length 14 meters ,height 60 and width 60 centimeters. The experimental results show when height of slot is below the stream bed as D, scour depth will be reduced about 20.34% to 39.73% in front of the pier and scour volume approximately 46.84% to 75.74% Keywords: Bridge pier, Slot, Scour, scour depth, scour volume
This study presents a laboratory experiments for evaluating the local scour depth
around S-shape solid non- submerged groynes using different number of these groynes
and also different distances between them as two countermeasures to reduce the
scour. The study was conducted in non- curved laboratory flume where uniform
cohesion-less sand of median size (d50) equal to (0.7 mm) was used as the bed
material. The physical hydraulic model of the groynes was made of polystyrene foam
with fixed dimensions to operate under steady subcritical flow and clear water
conditions. The studied parameters in this study were the number of groynes changed
three times (single, double, triple), the distances between them altered also three times
(1L, 1.5 L, 2L) and finally the hydraulic conditions (depth and velocity of the mean
flow) also changed four times for each parameter. A new empirical equation was
derived where its coefficient of determination indicates good agreement between the
predicted results and the observed ones experimentally.
Fundamentals of fluid flow, Darcy's law, Unsaturated Condition, Reynolds Number, Poiseuille’s Flow, Laplace Law, The one-dimensional vertical flow of water
Simulation of Sediment Transport in the Canal Using the Hec-Ras (Hydrologic E...inventionjournals
The underground canal of Southwest Kano Irrigation scheme was designed to ensure that water
is conveyed with minimal erosion and sedimentation but over time it has been silted up to the extent that its
conveyance capacity has significantly dropped. This study is based on simulation of sediment transport within
the underground canal in Southwest Kano Irrigation Scheme boundaries using Hydrologic Engineering Centre
– River Analysis System (HEC-RAS) model. Ackers-White sediment transport equation, engraved in the model,
was used to analyse sediment transport characteristics. The conceptual and physical parameters required in the
HEC-RAS model were determined through calibration and direct measurement respectively. The model was
calibrated based on the current operational conditions of the canal followed by simulation using the model to
determine the sediment discharge and deposition rates at different levels of flow in the canal. The Ackers-White
sediment transport equation predicted the sediment sizes which were deposited at specific sections of the canal
at different flow rates. Higher flow rates resulted in minimal deposition. As a sediment management strategy,
these sediment sizes could be screened off at the canal intake, to ensure that sediment passing through would be
transported out to the canal outlet without deposition.
EXPERIMENTAL STUDY OF BRIDGE PIER SHAPE TO MINIMIZE LOCAL SCOURIAEME Publication
The study of local scour around bridge piers is very important for safe design of piers and other hydraulic structures. In this study, shape of pier is the main concern with three different velocities (0.18, 0.25, and 0.3) m/sec and other parameters like flow depth, bed material and etc. are remain same for all experiments. The experiments were conducted using laboratory flume, operated under the clear water condition using sand as a bed material. The test program was done on ten different shapes, Circular, Rectangular, Octagonal, Chamfered, Hexagonal, Elliptical, Sharp, Joukowsky, Oblong, streamline. were used to investigate the effect of the bridge pier's shape on local scour to conclude the optimal shape that gives minimum depth of scour. Comparison of results show that scour at upstream is directly proportional to exposed area of upstream nose of pier.
In Soil, Generally there exists pores which are field with water. These pores are interconnected & hence it
becomes highly complex & intricate network of irregular tubes. Where there is pressure difference, water flows
from high potential to low potential zone. The pores may be large or small, may be irregular in shape. The
quantum of flow depends on the above. The ease with which water can flow through soil is the permeability of
the soil. Geotechnical engineers may come across the problem of soil which may be highly permeable or may
have restricted permeability. Engineers are needed to quantitatively assess the amount of flow likely to occur.
International Journal of Engineering Inventions (IJEI) provides a multidisciplinary passage for researchers, managers, professionals, practitioners and students around the globe to publish high quality, peer-reviewed articles on all theoretical and empirical aspects of Engineering and Science.
The peer-reviewed International Journal of Engineering Inventions (IJEI) is started with a mission to encourage contribution to research in Science and Technology. Encourage and motivate researchers in challenging areas of Sciences and Technology.
It is about hydraulic conductivity and flow of water under ground .It will tell you about how water flows through hydraulic gradient .it will brief you about test which are performed to determine hydraulic conductivity .and experimental approach of it .
DSD-INT 2019 Fine sediments - transport in suspension, storage and supply - F...Deltares
Presentation by Prof. Dr. Mário J. Franca, IHE Delft & Delft University of Technology, The Netherlands, at the Delft3D - User Days (Day 3a: River morphodynamics), during Delft Software Days - Edition 2019. Wednesday, 13 November 2019, Delft.
Simulation of Sediment Transport in the Canal Using the Hec-Ras (Hydrologic E...inventionjournals
The underground canal of Southwest Kano Irrigation scheme was designed to ensure that water
is conveyed with minimal erosion and sedimentation but over time it has been silted up to the extent that its
conveyance capacity has significantly dropped. This study is based on simulation of sediment transport within
the underground canal in Southwest Kano Irrigation Scheme boundaries using Hydrologic Engineering Centre
– River Analysis System (HEC-RAS) model. Ackers-White sediment transport equation, engraved in the model,
was used to analyse sediment transport characteristics. The conceptual and physical parameters required in the
HEC-RAS model were determined through calibration and direct measurement respectively. The model was
calibrated based on the current operational conditions of the canal followed by simulation using the model to
determine the sediment discharge and deposition rates at different levels of flow in the canal. The Ackers-White
sediment transport equation predicted the sediment sizes which were deposited at specific sections of the canal
at different flow rates. Higher flow rates resulted in minimal deposition. As a sediment management strategy,
these sediment sizes could be screened off at the canal intake, to ensure that sediment passing through would be
transported out to the canal outlet without deposition.
EXPERIMENTAL STUDY OF BRIDGE PIER SHAPE TO MINIMIZE LOCAL SCOURIAEME Publication
The study of local scour around bridge piers is very important for safe design of piers and other hydraulic structures. In this study, shape of pier is the main concern with three different velocities (0.18, 0.25, and 0.3) m/sec and other parameters like flow depth, bed material and etc. are remain same for all experiments. The experiments were conducted using laboratory flume, operated under the clear water condition using sand as a bed material. The test program was done on ten different shapes, Circular, Rectangular, Octagonal, Chamfered, Hexagonal, Elliptical, Sharp, Joukowsky, Oblong, streamline. were used to investigate the effect of the bridge pier's shape on local scour to conclude the optimal shape that gives minimum depth of scour. Comparison of results show that scour at upstream is directly proportional to exposed area of upstream nose of pier.
In Soil, Generally there exists pores which are field with water. These pores are interconnected & hence it
becomes highly complex & intricate network of irregular tubes. Where there is pressure difference, water flows
from high potential to low potential zone. The pores may be large or small, may be irregular in shape. The
quantum of flow depends on the above. The ease with which water can flow through soil is the permeability of
the soil. Geotechnical engineers may come across the problem of soil which may be highly permeable or may
have restricted permeability. Engineers are needed to quantitatively assess the amount of flow likely to occur.
International Journal of Engineering Inventions (IJEI) provides a multidisciplinary passage for researchers, managers, professionals, practitioners and students around the globe to publish high quality, peer-reviewed articles on all theoretical and empirical aspects of Engineering and Science.
The peer-reviewed International Journal of Engineering Inventions (IJEI) is started with a mission to encourage contribution to research in Science and Technology. Encourage and motivate researchers in challenging areas of Sciences and Technology.
It is about hydraulic conductivity and flow of water under ground .It will tell you about how water flows through hydraulic gradient .it will brief you about test which are performed to determine hydraulic conductivity .and experimental approach of it .
DSD-INT 2019 Fine sediments - transport in suspension, storage and supply - F...Deltares
Presentation by Prof. Dr. Mário J. Franca, IHE Delft & Delft University of Technology, The Netherlands, at the Delft3D - User Days (Day 3a: River morphodynamics), during Delft Software Days - Edition 2019. Wednesday, 13 November 2019, Delft.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
ER Publication,
IJETR, IJMCTR,
Journals,
International Journals,
High Impact Journals,
Monthly Journal,
Good quality Journals,
Research,
Research Papers,
Research Article,
Free Journals, Open access Journals,
erpublication.org,
Engineering Journal,
Science Journals,
Effect Of Water On Slope Stability And Investigation Of ΝΝw Drainage Techniqu...IJMER
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
Sediment Source and Transport in River Channels: Implications for River Struc...theijes
Rivers are important resources that play the role of life sustenance in nature by providing environmental, cultural and economic benefits including municipal water use, irrigation, hydropower, navigation, fishing and recreation. Since they are the corridors connecting terrestrial environment to the ocean realm, they always transport and accumulate sediments. Knowledge and understanding of sediment characteristics, channel processes, process of sediment source and transport in river channels is vital in modeling and managing rivers in terms of how they both transport and impact engineering structures erected on rivers. Although, ongoing research is beginning to fill in some of these gaps through the use of laboratory experiments and mathematical models, this has not been matched by sufficient progress in measuring and quantifying the bifurcation process in natural river channels, very often because natural rivers are far harder to study and the technology required still remains unavailable. When the rate of sediment influx is high along river channels, reservoirs in dams are filled up with sediment which might need dredging to remove the sediments. Also turbine blades of power plants are considerably disturbed as a result of sediment particles deposited on the blades; flow in culverts and around bridge piers are exposed to erosion of the bed thereby exposing the foundation. Problems arising from sediment transport and deposition can be mitigated by selecting suitable cross sections for the measurement of sediment flow rate parameters and removal of the sediment which would lead to the reduction of negative impacts on the river structures.
This study aims at investigating possible connections between point load index
(Is50) and the uniaxial compressive strength (UCS) for a Basaltic rock derived from
different regions in Jordan and examining potential relationships between Basalt
physical properties and ultrasonic pulse value (UPV). A series of lab experiments
including point load test, uniaxial compressive strength, Brazilian split test, ultrasonic
pulse velocity, dry density, and porosity were performed on a Basaltic rock cores with
dimension as per the ISRM standard. The obtained results indicated that the
relationship between unconfined compressive strength and point load test of Basalt is
restricted with the result of the previous studies and ranged between 20 to 24 times the
point load index values. Results also revealed that a good relationship may be derived
between Brazilian split test and unconfined compressive strength. Lastly, results
indicate a good relationship between ultrasonic pulse values (UPV) attained with both
porosity and dry density.
analysis of flow resistance in open channel for proper flow predictionINFOGAIN PUBLICATION
In an open channel flow, the Manning’s n depends on the bed material of the channel, the slope of the channel and the rate of discharge in the channel. Experiments are done with two bed materials, the original bed surface of the channel and with grass carper. The roughness coefficient is determined in various cases. The variations in roughness coefficient is tested with respect to flow parameters such as discharge, depth and bed slope. The effect of variations the flow parameters on different bed roughness is also analyzed by taking into account the original flume surface and grass carpet surface.
The International Journal of Engineering and Science (The IJES)theijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
The International Journal of Engineering and Science (The IJES)theijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
Behaviour of Single Pile in Reinforced Slope Subjected to Inclined Load IJERA Editor
Deep foundations, including driven piles, are used to support vertical loads of structures and lateral forces. Typical structures subjected to lateral loads include bridge abutments, transmission tower, sand offshore platforms. Traffic, wind, wave, and seismic forces are common types of lateral loads subjected to pile foundations. The present work is focused on understanding the lateral load capacity of vertical piles located near crest of the slope and subjected to the lateral and inclined loads. The experimental investigation was carried out to study the effect of reinforcing an earth slope on the inclined loading behavior of a single vertical pile located near the slope. Layers of geogrid were used to reinforce a sandy slope of 1V:2H. The parametric studies were performed by varying the length of pile(L), angle of inclination of load (θ), number of geogrid reinforcement (Nr) and crest distance. It was observed that the lateral load capacity of pile depends upon these parameters. The lateral load capacity of pile increases with increase in inclination of load, length of pile(L), number of geogrid reinforcement (Nr) and crest distance.
Behaviour of Single Pile in Reinforced Slope Subjected to Inclined LoadIJERA Editor
Deep foundations, including driven piles, are used to support vertical loads of structures and lateral forces. Typical structures subjected to lateral loads include bridge abutments, transmission tower, sand offshore platforms. Traffic, wind, wave, and seismic forces are common types of lateral loads subjected to pile foundations. The present work is focused on understanding the lateral load capacity of vertical piles located near crest of the slope and subjected to the lateral and inclined loads. The experimental investigation was carried out to study the effect of reinforcing an earth slope on the inclined loading behavior of a single vertical pile located near the slope. Layers of geogrid were used to reinforce a sandy slope of 1V:2H. The parametric studies were performed by varying the length of pile(L), angle of inclination of load (θ), number of geogrid reinforcement (Nr) and crest distance. It was observed that the lateral load capacity of pile depends upon these parameters. The lateral load capacity of pile increases with increase in inclination of load, length of pile(L), number of geogrid reinforcement (Nr) and crest distance
This comprehensive program covers essential aspects of performance marketing, growth strategies, and tactics, such as search engine optimization (SEO), pay-per-click (PPC) advertising, content marketing, social media marketing, and more
Exploring Career Paths in Cybersecurity for Technical CommunicatorsBen Woelk, CISSP, CPTC
Brief overview of career options in cybersecurity for technical communicators. Includes discussion of my career path, certification options, NICE and NIST resources.
New Explore Careers and College Majors 2024.pdfDr. Mary Askew
Explore Careers and College Majors is a new online, interactive, self-guided career, major and college planning system.
The career system works on all devices!
For more Information, go to https://bit.ly/3SW5w8W
Resumes, Cover Letters, and Applying OnlineBruce Bennett
This webinar showcases resume styles and the elements that go into building your resume. Every job application requires unique skills, and this session will show you how to improve your resume to match the jobs to which you are applying. Additionally, we will discuss cover letters and learn about ideas to include. Every job application requires unique skills so learn ways to give you the best chance of success when applying for a new position. Learn how to take advantage of all the features when uploading a job application to a company’s applicant tracking system.
1. water
Article
Scour around Spur Dike in Sand–Gravel Mixture Bed
Manish Pandey 1 , Wei Haur Lam 2,*, Yonggang Cui 2, Mohammad Amir Khan 3,
Umesh Kumar Singh 3 and Z. Ahmad 3
1 Department of Soil and Water Conservation, National Chung Hsing University, Taichung City 402, Taiwan
2 State Key Laboratory of Hydraulic Engineering Simulation and Safety, Tianjin University,
Tianjin 300350, China
3 Department of Civil Engineering, Indian Institute of Technology Roorkee, Roorkee 247667, India
* Correspondence: wlam@tju.edu.cn or joshuawhlam@hotmail.com
Received: 21 June 2019; Accepted: 5 July 2019; Published: 10 July 2019
Abstract: Scour is the main cause of failure for spur dike. The accurate prediction of scour around
spur dike is essential to design a spur dike. The present study focuses on the maximum scour depth
in equilibrium condition and parameters, which influence it in a sand–gravel mixture bed. Outcomes
of the present experimental study showed that the non-dimensional maximum equilibrium scour
depth increases with critical velocity ratio (U/Uca), water depth-armour particle ratio (h/da), Froude
number for sediment mixture (Frsm), water depth-spur dike length ratio (h/l), and decreases with
increase in armour particle-spur dike length ratio (da/l). The maximum scour depth is proportional
to dimensionless parameters of U/Uca, h/da, Frsm, h/l, but the scour depth is inverse proportional to
da/l. Scour around spur dike in a sand–gravel mixture is mainly influenced by the property of the
sediment mixture. The scour increases with decrease in non-uniformity of the sediment mixture.
A non-linear empirical equation is proposed to estimate the maximum scour depth at an upstream
nose of rectangular spur dike with a maximum error of 15%. The sensitivity analysis indicates that
the maximum non-dimensional equilibrium scour depth depends on Frsm, followed by the secondary
sensible parameters da/l, h/l, and h/da.
Keywords: spur dike; maximum equilibrium scour depth; sand–gravel mixture; clear-water scour
1. Introduction
Spur dike is a manmade hydraulic structure, which is also known as groin and spur. A
spur dike protects the stream banks by reducing the flow velocity against the fluvial hydraulic
processes. The construction cost of spur dikes in an alluvial stream is as cheap as an easily adaptable
hydraulic structure. Spur dikes are fixed in vertical/perpendicular, declined or inclined positions
to the longitudinal direction of the stream. The designing criteria of vertical spur dikes are more
economic and convenient compared to the angled spur dikes [1]. The present study only focuses on
the rectangular vertical spur dikes, which are fixed perpendicular to the flow. Spur dikes are identified
as an effective hydraulic structure to reduce the flow velocity for river bank protection [1–3]. After
fixing a spur dike, the flow processes in the stream are different to disturb the flow characteristics. This
process around the spur dike is complex with a local scour phenomenon around the spur dikes. The
scour study around the spur dikes is important for river engineering to provide practical guidelines [4].
Local scour is a well-defined term in river engineering and is described as the removal of sediment
particles from the alluvial streams. It is recognized as the main reason for the failure of hydraulic
structures [5–8]. Figure 1 shows an actual picture of the failure of a vertical spur dike in the river Gaula
near Haldwani, Uttrakhand in India.
Water 2019, 11, 1417; doi:10.3390/w11071417 www.mdpi.com/journal/water
2. Water 2019, 11, 1417 2 of 14
Water 2019, 11, x FOR PEER REVIEW 2 of 14
Figure 1. Failure of spur dike at the river Gaula near Haldwani, Uttrakhand in India.
Maximum scour depth around spur dikes in uniform sediment beds are studied extensively
compared to the sediment mixtures [9–14]. However, rivers in upper reaches or in hilly streams are
mainly composed of different sediment mixtures or non-uniform sediments. Uniform sediment is
defined as when the value of the geometric standard deviation 𝜎 = 𝑑 𝑑⁄ is greater than 1.4
[14], where d84 and d16 are particle sizes at 84% and 16% finer, respectively. In non-uniform sediment
mixtures, finer particles are being removed first, followed by the coarser particles trying to act as a
protective layer near the bridge elements due to the complex sediment transport processes [5]. This
protective layer of coarser particles is known as armour layer. The median diameter (da) of the armour
layer is usually larger than the parent median diameter (d) of the streambed [15]. After the formation
of an armour layer around a spur dike, further removal of sediment particles under the same
hydraulic condition is very difficult. Kothyari et al. [6] stated that the armour layers of concern to
calculate the scour depths around the bridge elements, are those where the bridge element is fixed in
a streambed of relatively fine sediment covered by a coarser sediment layer (armour layer),
developed due to the sorting of non-uniform sediments. The scour phenomenon at equilibrium scour
stage is analysed by the approach flow parameters, the characteristics of armour particles along with
parent bed material [16]. Most of the previous studies are limited to uniform sediment and therefore,
in this research, the effect of non-uniformity of sediment on maximum scour depth was studied by
performing 32 experiments.
Several investigators stated that the condition of incipient motion develops in the riverbed when
shear velocity is greater than the critical shear velocity of riverbed materials [17,18]. After incipient
condition, the additional shear stresses start the scour process around the spur dikes, piers, and
abutments [17,18]. Melville [19] indicated that the scour around bridge abutment occurs when the
approach shear velocity is nearly half of the critical shear velocity. Kothyari and Ranga Raju [6], and
Melville [19] stated that spur dikes have an analogous scour process of abutments. It has been
specified by Kothyari and Ranga Raju [6] that any reference ended to vertical wall abutment hereafter
also holds good references for vertical spur dike. Melville [19] identified that the scour hole around
abutment forms a primary vortex that sinks into the scour hole and prime agent for continuous scour
progress. The scour process ends in a sand–gravel mixture by developing a stable layer armour layer.
Once a scour hole reaches an equilibrium condition, the armour layer does not allow further change
in the scour hole. Generally, an armour layer has uniform sediment properties with less geometric
standard deviation than coarser sediments [15]. An armour layer depends on the quantity and
strength of coarser particles in a sediment mixture. Sui et al. [16] stated that the stability and strength
of the scour hole depend on the properties of coarser particles in a sediment mixture.
Previous investigators stated that the gravel particles are steadier inside the scour hole due to its
larger mass. Larger mass particles require more energy to remove from the scour hole [6,16]. At the
same time, some sand particles are covered by the gravel particles and, gradually, this process results
Figure 1. Failure of spur dike at the river Gaula near Haldwani, Uttrakhand in India.
Maximum scour depth around spur dikes in uniform sediment beds are studied extensively
compared to the sediment mixtures [9–14]. However, rivers in upper reaches or in hilly streams are
mainly composed of different sediment mixtures or non-uniform sediments. Uniform sediment is
defined as when the value of the geometric standard deviation σ = d84/d16 is greater than 1.4 [14],
where d84 and d16 are particle sizes at 84% and 16% finer, respectively. In non-uniform sediment
mixtures, finer particles are being removed first, followed by the coarser particles trying to act as
a protective layer near the bridge elements due to the complex sediment transport processes [5].
This protective layer of coarser particles is known as armour layer. The median diameter (da) of the
armour layer is usually larger than the parent median diameter (d) of the streambed [15]. After the
formation of an armour layer around a spur dike, further removal of sediment particles under the
same hydraulic condition is very difficult. Kothyari et al. [6] stated that the armour layers of concern to
calculate the scour depths around the bridge elements, are those where the bridge element is fixed in a
streambed of relatively fine sediment covered by a coarser sediment layer (armour layer), developed
due to the sorting of non-uniform sediments. The scour phenomenon at equilibrium scour stage is
analysed by the approach flow parameters, the characteristics of armour particles along with parent
bed material [16]. Most of the previous studies are limited to uniform sediment and therefore, in this
research, the effect of non-uniformity of sediment on maximum scour depth was studied by performing
32 experiments.
Several investigators stated that the condition of incipient motion develops in the riverbed when
shear velocity is greater than the critical shear velocity of riverbed materials [17,18]. After incipient
condition, the additional shear stresses start the scour process around the spur dikes, piers, and
abutments [17,18]. Melville [19] indicated that the scour around bridge abutment occurs when the
approach shear velocity is nearly half of the critical shear velocity. Kothyari and Ranga Raju [6], and
Melville [19] stated that spur dikes have an analogous scour process of abutments. It has been specified
by Kothyari and Ranga Raju [6] that any reference ended to vertical wall abutment hereafter also holds
good references for vertical spur dike. Melville [19] identified that the scour hole around abutment
forms a primary vortex that sinks into the scour hole and prime agent for continuous scour progress.
The scour process ends in a sand–gravel mixture by developing a stable layer armour layer. Once a
scour hole reaches an equilibrium condition, the armour layer does not allow further change in the
scour hole. Generally, an armour layer has uniform sediment properties with less geometric standard
deviation than coarser sediments [15]. An armour layer depends on the quantity and strength of
coarser particles in a sediment mixture. Sui et al. [16] stated that the stability and strength of the scour
hole depend on the properties of coarser particles in a sediment mixture.
3. Water 2019, 11, 1417 3 of 14
Previous investigators stated that the gravel particles are steadier inside the scour hole due to its
larger mass. Larger mass particles require more energy to remove from the scour hole [6,16]. At the
same time, some sand particles are covered by the gravel particles and, gradually, this process results
in the development of clusters of gravel particles. For a limited spread, this cluster illustrates similar
characteristics. It has been stated by Kothyari et al. [5] that the development of an armour layer might
be observed as a continuous process of collapses and the creation of clusters.
The parameters influencing the maximum equilibrium scour depth around a rectangular spur dike
consist of the geometry of spur dikes, the sediment properties, and the flow parameters. Maximum
equilibrium scour depth (dsa) around a rectangular spur dike in a sediment mixture can be written as,
dsa = f(ds, da, d, σ, Ucs, Uca, Frd, Frsm, ρ, U, h, l) (1)
In Equation (1), dsa is the maximum scour depth at equilibrium condition; ds, da, d, σ, Uca, Ucs are
sediment parameters; ρ, U, h are flow parameters, and l is the spur dike geometry parameters. Where
ds is a median diameter of sand, da is a median diameter of armour or gravel particles, d is an effective
median diameter of sediment mixture, σ is a standard deviation of sediment mixture, Ucs and Uca are
critical velocities of sand and armour particles, respectively. Frd = U/{(S−1)gd}0.5 is densimetric particle
Froude number and Frsm = σ−1/3Frd is densimetric Froude number of the sediment mixture [15]. U
is time-averaged approach velocity, S is relative density, ρ is the density of water, g is gravitational
acceleration, l is transverse length of spur dike.
2. Experimental Setup and Procedure
In the current study, 32 experiments were completed in a hydraulics laboratory, in the civil
engineering department, at I.I.T. Roorkee, India, by using a rectangular flume of 24.0 m length and
1.0 m width, and a sediment depth of up to 0.25 m, as shown in Figure 2a. A working-section of the
flume, 4.0 m × 1.0 m × 0.25 m, which begins at a distance of 12.0 m from the flume entrance. All tests
were completed under clear water scour condition. Four different rectangular spur dikes were used in
this study, which were made of 5 mm thick cast iron plates. All experiments were completed under
different flow conditions and sediment properties at different time average velocities (U), approach flow
depths (h), transverse length of spur dike (l), and median diameter of parent streambed particles (d).
Working-section of flume was fully filled with two different sediment mixtures, (i) 50% sand
(ds = 0.27 mm and σ = 1.22) and 50% gravel (da = 2.7 mm and σ = 1.21), and (ii) 50% sand (ds = 0.27 mm
and σ = 1.22) and 50% gravel (da = 3.1 mm and σ = 1.18). These sediment mixtures were filled up to
the longitudinal level of the flume bed. A 2-D profiler was used to level the working section. Four
different rectangular spur dikes having transverse lengths (l) of 6.0 cm, 9.0 cm, 11.5 cm, and 14.0 cm
were used for the experiments. The water supply into the flume was regulated by a valve, which
was provided in the inlet pipe. An ultrasonic flow meter was provided at the flume entrance pipe to
measure the flow rate. Approach flow depth was adjusted using the tailgate, which was located at the
downstream end of the flume. A wave regulator was facilitated at flume entrance to produce a uniform
or near-uniform flow condition in the experimental flume. The maximum equilibrium scour depth
was measured with a Vernier point gauge. The scour depth was measured at upstream nose of the spur
dike and the upstream wall-junction of the spur dike with different time intervals. Figure 2b shows the
variation of temporal scour depth (dst) at upstream spur dike’s nose and spur dike’s wall-junction. All
experiments were completed for 20 h. However, experimentally, we saw that the equilibrium scour
stage was reached within 10–14 h, as can be seen Figure 2b. After the equilibrium time of scour, the
scour depth at upstream nose and wall-junction of the spur dike was the same at every 30 min interval.
At the equilibrium scour condition, the maximum scour depth always occurred at the upstream nose
of the spur dike. In the present study, the maximum equilibrium scour depth (dsa) at the nose of spur
dike was only considered for analysis. Before the start of each experiment, the test-section of flume
was perfectly levelled with respect to the flume bed and covered with a thin Perspex sheet. Once
4. Water 2019, 11, 1417 4 of 14
pre-set flow conditions were achieved, the Perspex sheet was separated very sensibly to avoid the
undesirable scour around the pier. Table 1 illustrates the maximum scour depth along with flow and
sediment properties.
Water 2019, 11, x FOR PEER REVIEW 4 of 14
In this experimental study, the time-averaged velocity was taken in place of approach shear
velocity (u*) to study the maximum equilibrium scour depth. The critical shear velocity of flume bed
particles and armour layer particles was calculated by Shield’s curve. The corresponding values of
critical velocities (Uca) were calculated using Lauchlan and Melville [20] in Equation (2).
𝑈 𝑐𝑎
𝑢∗𝑐𝑎
= 5.75𝑙𝑜𝑔
ℎ
𝑘 𝑠
6 (2)
where ks is the height of roughness.
(a)
(b)
Figure 2. Experiments. (a) Photometric view. (b) Scour depth variations with time at upstream nose
and wall-junction of the spur dike.
Figure 2. Experiments. (a) Photometric view. (b) Scour depth variations with time at upstream nose
and wall-junction of the spur dike.
5. Water 2019, 11, 1417 5 of 14
Table 1. Scour depth data at equilibrium condition.
Exp. Run h (m) l (m) U (m/s) ds (m) da (m) Frsm U/Uca da (m)
R1 0.112 0.140 0.41 0.00027 0.0027 1.77 0.90 0.149
R2 0.105 0.140 0.35 0.00027 0.0027 1.51 0.77 0.111
R3 0.1 0.140 0.31 0.00027 0.0027 1.23 0.68 0.095
R4 0.09 0.140 0.28 0.00027 0.0027 1.21 0.61 0.072
R5 0.112 0.115 0.41 0.00027 0.0027 1.77 0.90 0.128
R6 0.105 0.115 0.35 0.00027 0.0027 1.51 0.77 0.091
R7 0.1 0.115 0.31 0.00027 0.0027 1.34 0.68 0.076
R8 0.09 0.115 0.28 0.00027 0.0027 1.21 0.61 0.057
R9 0.112 0.090 0.41 0.00027 0.0027 1.77 0.90 0.104
R10 0.105 0.090 0.35 0.00027 0.0027 1.51 0.77 0.078
R11 0.1 0.090 0.31 0.00027 0.0027 1.34 0.68 0.063
R12 0.09 0.090 0.28 0.00027 0.0027 1.21 0.61 0.051
R13 0.112 0.060 0.41 0.00027 0.0027 1.77 0.90 0.074
R14 0.105 0.060 0.35 0.00027 0.0027 1.51 0.77 0.058
R15 0.1 0.060 0.31 0.00027 0.0027 1.34 0.68 0.045
R16 0.09 0.060 0.28 0.00027 0.0027 1.21 0.61 0.038
R17 0.112 0.140 0.41 0.00027 0.0031 1.62 0.84 0.127
R18 0.105 0.140 0.35 0.00027 0.0031 1.38 0.71 0.096
R19 0.1 0.140 0.31 0.00027 0.0031 1.22 0.63 0.074
R20 0.09 0.140 0.28 0.00027 0.0031 1.10 0.57 0.057
R21 0.112 0.115 0.41 0.00027 0.0031 1.62 0.84 0.107
R22 0.105 0.115 0.35 0.00027 0.0031 1.38 0.71 0.078
R23 0.1 0.115 0.31 0.00027 0.0031 1.22 0.63 0.059
R24 0.09 0.115 0.28 0.00027 0.0031 1.10 0.57 0.047
R25 0.112 0.090 0.41 0.00027 0.0031 1.62 0.84 0.086
R26 0.105 0.090 0.35 0.00027 0.0031 1.38 0.71 0.068
R27 0.11 0.090 0.31 0.00027 0.0031 1.22 0.63 0.054
R28 0.13 0.090 0.28 0.00027 0.0031 1.10 0.57 0.041
R29 0.12 0.060 0.41 0.00027 0.0031 1.62 0.84 0.058
R30 0.11 0.060 0.35 0.00027 0.0031 1.38 0.71 0.043
R31 0.13 0.060 0.31 0.00027 0.0031 1.22 0.63 0.037
R32 0.12 0.060 0.28 0.00027 0.0031 1.10 0.57 0.032
In this experimental study, the time-averaged velocity was taken in place of approach shear
velocity (u*) to study the maximum equilibrium scour depth. The critical shear velocity of flume bed
particles and armour layer particles was calculated by Shield’s curve. The corresponding values of
critical velocities (Uca) were calculated using Lauchlan and Melville [20] in Equation (2).
Uca
u∗ca
= 5.75log
h
ks
+ 6 (2)
where ks is the height of roughness.
3. Results and Discussion
3.1. Maximum Scour Depth and Location
The scour progress ends in a sand–gravel mixture when a stable armour layer forms around the
spur dike. This condition is also known as equilibrium scour condition. Maximum scour depth at
this condition is well-known as maximum equilibrium scour depth or maximum scour depth (dsa).
The equilibrium condition of scour strongly depends on the approach flow parameters, characteristics
of the armour bed, and the dimension of the spur dike. The estimation of dsa around the spur dike is
an important function for the safe and efficient design of the spur dikes.
Maximum depth of scour (dsa) at equilibrium condition is a key factor for a non-dimensional
analysis. Experimentally, it was observed that dsa always occurs at the upstream nose of the spur
6. Water 2019, 11, 1417 6 of 14
dike. Distribution of high bed shear stresses in armour beds around the bridge elements is responsible
for the maximum scour depth [16]. It was observed that the scour depth at spur dike nose in
equilibrium stage was comparatively more as compared to the spur dike wall-junction, as shown
in Figures 2b and 3. Figure 3 illustrates the position of maximum depth of scour and scour depth
variation in equilibrium condition.Water 2019, 11, x FOR PEER REVIEW 6 of 14
Figure 3. Geometry of scour hole at equilibrium condition for R10.
3.2. Influence of Different Parameters on Maximum Scour
The stability of the armour layer around the spur dike is influenced by properties of armour
particles, the sediment mixture, and approach flow properties. The maximum equilibrium scour
depth (dsa) variations with time-averaged velocity (U) for different transverse lengths (l) of spur dike
along with different sediment sizes are shown in Figure 4a. It can be seen that larger armour particles
show less variation in scour depth with time-averaged velocity, while smaller armour particle beds
with a larger transverse length of spur dike show higher scour depth variation. The maximum depth
of scour (dsa) increases with the increase in time-averaged velocity for any sizes of armour particle, as
referred in Figure 4a. Scour depth variation increases with an increase in U/Uca. For a particular range
of U/Uca, dsa increases with increase in l, as shown in Figure 4b.
Figure 5a–d shows the variations of dsa/l vs. h/l, dsa/l vs. da/l, dsa/l vs. Frsm, and dsa/l vs. h/da. The
organised variation between non-dimensional scour depth and flow shallowness ratio (h/l) clearly
states that the variation of maximum scour depth in non-dimensional form increases with a decrease
in l. For a particular spur dike, dsa/l increases with increase in the flow shallowness ratio, as can be
seen in Figure 5a. The results indicate that the rate of maximum scour depth variation in the sand–
gravel mixture is found to be at a maximum for the longest spur dike, as shown in Figure 5a.
Figure 5b illustrates the variation of da/l with respect to the non-dimensional scour depth (dsa/l).
It is clearly visible from Figure 5b, the magnitude of dsa/l increases with a decrease in da/l. For a
particular spur dike, the maximum scour depth variation increases with decrease in armour particle
size (Figure 5b). For the constant value of armour particle, the maximum scour depth variation
decreases with a decrease in transverse length of spur dike. This implies that the variation of
maximum non-dimensional scour depth increases with a decrease in armour particle and an increase
in the transverse length of spur dike.
Figure 3. Geometry of scour hole at equilibrium condition for R10.
3.2. Influence of Different Parameters on Maximum Scour
The stability of the armour layer around the spur dike is influenced by properties of armour
particles, the sediment mixture, and approach flow properties. The maximum equilibrium scour depth
(dsa) variations with time-averaged velocity (U) for different transverse lengths (l) of spur dike along
with different sediment sizes are shown in Figure 4a. It can be seen that larger armour particles show
less variation in scour depth with time-averaged velocity, while smaller armour particle beds with a
larger transverse length of spur dike show higher scour depth variation. The maximum depth of scour
(dsa) increases with the increase in time-averaged velocity for any sizes of armour particle, as referred
in Figure 4a. Scour depth variation increases with an increase in U/Uca. For a particular range of U/Uca,
dsa increases with increase in l, as shown in Figure 4b.
Figure 5a–d shows the variations of dsa/l vs. h/l, dsa/l vs. da/l, dsa/l vs. Frsm, and dsa/l vs. h/da.
The organised variation between non-dimensional scour depth and flow shallowness ratio (h/l) clearly
states that the variation of maximum scour depth in non-dimensional form increases with a decrease
in l. For a particular spur dike, dsa/l increases with increase in the flow shallowness ratio, as can be seen
in Figure 5a. The results indicate that the rate of maximum scour depth variation in the sand–gravel
mixture is found to be at a maximum for the longest spur dike, as shown in Figure 5a.
7. Water 2019, 11, 1417 7 of 14
Water 2019, 11, x FOR PEER REVIEW 7 of 14
Figure 4. Maximum scour depth of spur dike (a) Depth with time-averaged velocity, and (b)
Depth with transverse lengthsThe present study deals with the sand–gravel mixture and found that
the variation of scour depth in different sediment mixtures is influenced by the non-uniformity of
sediment. Hence, the authors analysed the influence of sediment mixture on maximum scour depth
(dsa) in terms of sediment mixture Froude number (Frsm = σ−1/3Frd). Figure 5c illustrates the effect of Frsm
on maximum scour depth. It was observed that the non-uniformity factor of sediment plays a
significant role in scour processes for non-uniform sediment’s case. For a constant dimension of spur
dike, the maximum scour depth in non-dimensional form increases with Frsm (Figure 5c). It means
that the maximum scour depth increases with a decrease in non-uniformity of sediment. It was also
observed that the development of armour layer in the scoured region results in the exposure of
coarser gravel size due to washing out of the finer gravel particles.
0
0.1
0.2
0.2 0.3 0.4 0.5
dsa(m)
U (m/s)
0
0.05
0.1
0.15
0.2
0 0.05 0.1 0.15
dsa(m)
l (m)
U/Uca=0.80-0.90
U/Uca=0.70-0.80
U/Uca=0.60-0.70
U/Uca=0.50-0.60
Figure 4. Maximum scour depth of spur dike (a) Depth with time-averaged velocity, and (b) Depth
with transverse lengths.
Figure 5b illustrates the variation of da/l with respect to the non-dimensional scour depth (dsa/l).
It is clearly visible from Figure 5b, the magnitude of dsa/l increases with a decrease in da/l. For a
particular spur dike, the maximum scour depth variation increases with decrease in armour particle
size (Figure 5b). For the constant value of armour particle, the maximum scour depth variation
decreases with a decrease in transverse length of spur dike. This implies that the variation of maximum
non-dimensional scour depth increases with a decrease in armour particle and an increase in the
transverse length of spur dike.
The present study deals with the sand–gravel mixture and found that the variation of scour depth
in different sediment mixtures is influenced by the non-uniformity of sediment. Hence, the authors
analysed the influence of sediment mixture on maximum scour depth (dsa) in terms of sediment mixture
Froude number (Frsm = σ−1/3Frd). Figure 5c illustrates the effect of Frsm on maximum scour depth.
It was observed that the non-uniformity factor of sediment plays a significant role in scour processes
8. Water 2019, 11, 1417 8 of 14
for non-uniform sediment’s case. For a constant dimension of spur dike, the maximum scour depth
in non-dimensional form increases with Frsm (Figure 5c). It means that the maximum scour depth
increases with a decrease in non-uniformity of sediment. It was also observed that the development of
armour layer in the scoured region results in the exposure of coarser gravel size due to washing out of
the finer gravel particles.
Water 2019, 11, x FOR PEER REVIEW 8 of 14
Figure 5d shows the variation in the gradient of the trend lines dsa/l vs. h/da with different
dimensions of spur dike. The pattern of trend lines indicates that the dsa/l increases with the increase
in h/da, as can be seen in Figure 5d. The influence of h/da was more visible for a particular spur dike’s
case. The rate of maximum scour depth variation increases with the length of spur dike.
0
0.5
1
1.5
0.5 1 1.5 2
dsa/l
h/l
l=14.0 cm
l=11.5 cm
l=9.0 cm
l=6.0 cm
(a)
0
0.5
1
1.5
0 0.01 0.02 0.03 0.04 0.05
dsa/l
da/l
Figure 5. Cont.
9. Water 2019, 11, 1417 9 of 14
Water 2019, 11, x FOR PEER REVIEW 9 of 14
Figure 5. Influence of parameters on maximum non-dimensional scour depth. (a) dsa/l vs. h/l. (b)
dsa/l vs. da/l. (c) dsa/l vs. Frsm. (d) dsa/l vs. h/da.
3.3. Maximum Scour Depth
The maximum scour depth around a rectangular spur dike was briefly explained in the above
sections. Equation (1) shows the dependent parameters of a maximum equilibrium scour depth
relationship. In a sediment mixture, parent bed material and armour particles are the most important
parameters [16]. By using Buckingham’s pi theorem, Equation (1) may be written in a non-
dimensional form in Equation (3) as:
𝑑 𝑠𝑎
𝑙
= 𝑓 𝐅 𝐫𝑠𝑚,
𝑑 𝑎
𝑙
,
ℎ
𝑙
,
ℎ
𝑑 𝑎
(3)
The influence of different parameters on maximum equilibrium scour depth is discussed in the
previous section. An empirical Equation (4) was derived to compute the maximum equilibrium scour
depth using these influencing parameters. This equation was derived by using a nonlinear regression
method. Equation (4) calculates the maximum equilibrium scour depth around a rectangular spur
0
0.5
1
1.5
1.0 1.5 2.0
dsa/l
Frsm
l=14.0 cm
l=11.5 cm
l=9.0 cm
l=6.0 cm
0
0.5
1
1.5
25 30 35 40 45
dsal
h/da
l=14.0 cm
l=11.5 cm
l=9.0 cm
l=6.0 cm
Figure 5. Influence of parameters on maximum non-dimensional scour depth. (a) dsa/l vs. h/l. (b) dsa/l
vs. da/l. (c) dsa/l vs. Frsm. (d) dsa/l vs. h/da.
Figure 5d shows the variation in the gradient of the trend lines dsa/l vs. h/da with different
dimensions of spur dike. The pattern of trend lines indicates that the dsa/l increases with the increase in
h/da, as can be seen in Figure 5d. The influence of h/da was more visible for a particular spur dike’s case.
The rate of maximum scour depth variation increases with the length of spur dike.
3.3. Maximum Scour Depth
The maximum scour depth around a rectangular spur dike was briefly explained in the above
sections. Equation (1) shows the dependent parameters of a maximum equilibrium scour depth
relationship. In a sediment mixture, parent bed material and armour particles are the most important
parameters [16]. By using Buckingham’s pi theorem, Equation (1) may be written in a non-dimensional
form in Equation (3) as:
dsa
l
= f Frsm,
da
l
,
h
l
,
h
da
(3)
10. Water 2019, 11, 1417 10 of 14
The influence of different parameters on maximum equilibrium scour depth is discussed in the
previous section. An empirical Equation (4) was derived to compute the maximum equilibrium scour
depth using these influencing parameters. This equation was derived by using a nonlinear regression
method. Equation (4) calculates the maximum equilibrium scour depth around a rectangular spur
dike at its upstream nose. Equation (4) was also verified with 30% verification datasets, as shown in
Figure 6a,b. Figure 6c illustrates the variation between percentage error and total experimental data
frequency. All datasets were found inside the ±15% error, as can be seen in Figure 6c.
dsa
l
= 0.07(Frsm)1.5 da
l
−0.2
h
l
0.35
h
da
0.33
(4)
Water 2019, 11, x FOR PEER REVIEW 10 of 14
dike at its upstream nose. Equation (4) was also verified with 30% verification datasets, as shown in
Figure 6a,b. Figure 6c illustrates the variation between percentage error and total experimental data
frequency. All datasets were found inside the ±15% error, as can be seen in Figure 6c.
𝑑 𝑠𝑎
𝑙
= 0.07 𝐅 𝐫𝑠𝑚
1.5
𝑑 𝑎
𝑙
0.2
ℎ
𝑙
0.35
ℎ
𝑑 𝑎
0.33
(4)
0
0.5
1
1.5
0 0.5 1 1.5
dsa/l(Computeddata)
dsa/l (Experimental data)
(a)
0
0.5
1
1.5
0 0.5 1 1.5
dsa/l(Computeddata)
dsa/l (Experimental data)
Figure 6. Cont.
11. Water 2019, 11, 1417 11 of 14
Water 2019, 11, x FOR PEER REVIEW 11 of 14
Figure 6. Experimental vs. computed maximum non-dimensional scour depths. (a) 70% training
datasets. (b) 30% validation datasets. (c) Comparison between percentage data frequency and
percentage error.
3.4. Sensitivity Analysis
A sensitivity analysis was done to classify the most critical parameter, which affects the
maximum equilibrium scour depth. The sensitivity analysis was done by taking the average value of
all dependent and independent parameters. An assumption was taken during the sensitivity analysis,
i.e., each input variable is an error independent variable. The average values of input parameters Frsm,
da/l, h/l, and h/da for the datasets used in this analysis are 1.4, 0.032, 1.11, and 35.25, respectively.
If a percentage error ΔŶ in the output is known as the difference between values of output
computed for inputs χ and χ + Δχ, then the percentage error might be estimated as the absolute
sensitivity (α = ΔŶ/Δχ). Here, the output is χ = dsa/l and input χ = Frsm, da/l, h/l, and h/da. The error also
can be expressed in a relative form = ΔŶ/Ŷ. The error ΔŶ in output is fundamentally the deviation
sensitivity with Δχ being the error. The relative sensitivity can be expressed = (χ.ΔŶ)/( Ŷ.Δχ) [21].
The sensitivity analysis is completed by changing each input parameter by ±10%. The outcomes
of sensitivity analysis are shown in Tables 2 and 3, which show that Frsm is the most sensitive
parameter followed by da/l, h/l, and h/da. For 10% increase in χ, the relative sensitivity of Frsm is nearly
8.5, 2.7, and 2.8 times of da/l, h/l, and h/da, respectively. However, for a 10% decrease in χ, the relative
sensitivity of Frsm is nearly 1.7, 70.4, and 30.2 times of da/l, h/l, and h/da, respectively. Hence, it must be
said that the accuracy of Equation (4) significantly depends on Frsm, followed by da/l, h/l, and h/da.
Table 2. Results of sensitivity analysis with 10% increment in Δχ.
χ Δ χ ΔŶ α
Frsm 0.14 0.147 1.060 0.199 1.991
da/l 0.003 0.017 5.432 0.023 0.235
h/l 0.111 0.055 0.496 0.074 0.745
h/da 3.53 0.053 0.015 0.072 0.722
Table 3. Results of sensitivity analysis with 10% reduction in Δχ.
χ Δ χ ΔŶ α
Frsm 0.14 −0.083 −0.599 −0.113 −1.126
da/l 0.003 0.048 15.124 0.065 0.654
h/l 0.111 0.001 0.011 0.002 0.016
0
20
40
60
80
100
0 5 10 15
Datafrequency(%)
% Error
Figure 6. Experimental vs. computed maximum non-dimensional scour depths. (a) 70% training
datasets. (b) 30% validation datasets. (c) Comparison between percentage data frequency and
percentage error.
3.4. Sensitivity Analysis
A sensitivity analysis was done to classify the most critical parameter, which affects the maximum
equilibrium scour depth. The sensitivity analysis was done by taking the average value of all dependent
and independent parameters. An assumption was taken during the sensitivity analysis, i.e., each input
variable is an error independent variable. The average values of input parameters Frsm, da/l, h/l, and
h/da for the datasets used in this analysis are 1.4, 0.032, 1.11, and 35.25, respectively.
If a percentage error ∆ ˆY in the output is known as the difference between values of output
computed for inputs χ and χ + ∆χ, then the percentage error might be estimated as the absolute
sensitivity (α = ∆ ˆY/∆χ). Here, the output is χ = dsa/l and input χ = Frsm, da/l, h/l, and h/da. The error also
can be expressed in a relative form β = ∆ ˆY/ ˆY. The error ∆ ˆY in output is fundamentally the deviation
sensitivity with ∆χ being the error. The relative sensitivity can be expressed ω = (χ.∆ ˆY)/( ˆY.∆χ) [21].
The sensitivity analysis is completed by changing each input parameter by ±10%. The outcomes
of sensitivity analysis are shown in Tables 2 and 3, which show that Frsm is the most sensitive parameter
followed by da/l, h/l, and h/da. For 10% increase in χ, the relative sensitivity of Frsm is nearly 8.5, 2.7, and
2.8 times of da/l, h/l, and h/da, respectively. However, for a 10% decrease in χ, the relative sensitivity of
Frsm is nearly 1.7, 70.4, and 30.2 times of da/l, h/l, and h/da, respectively. Hence, it must be said that the
accuracy of Equation (4) significantly depends on Frsm, followed by da/l, h/l, and h/da.
Table 2. Results of sensitivity analysis with 10% increment in ∆χ.
χ ∆χ ∆ ˆY α β ω
Frsm 0.14 0.147 1.060 0.199 1.991
da/l 0.003 0.017 5.432 0.023 0.235
h/l 0.111 0.055 0.496 0.074 0.745
h/da 3.53 0.053 0.015 0.072 0.722
12. Water 2019, 11, 1417 12 of 14
Table 3. Results of sensitivity analysis with 10% reduction in ∆χ.
χ ∆χ ∆ ˆY α β ω
Frsm 0.14 −0.083 −0.599 −0.113 −1.126
da/l 0.003 0.048 15.124 0.065 0.654
h/l 0.111 0.001 0.011 0.002 0.016
h/da 3.53 0.003 0.001 0.004 0.035
A performance index (discrepancy ratio) was also computed using the present experimental
datasets. For a predictable estimation of the difference between calculated and experimental values of
dsa/l, the discrepancy ratio is defined in Equation (5) as:
Discrepancy Ratio (DR) = log
dsa_calculated
dsa_experimental
(5)
For DR = 0, the computed values of dsa/l are identical to the experimental values of dsa/l.
For negative/positive values of discrepancy ratio, the calculated values of dsa/l is smaller/greater than
the experimental values. Accuracy is described as the frequency of cases for which the discrepancy
ratio is within a suitable range for the total number of data, as can be seen in Figure 7. Data frequency
within DR = ±0.01 is 23 out of total 32 datasets. Discrepancy ratio analysis shows good agreements
between calculated and experimental values of maximum scour depth, as can be seen in Figure 7.
Water 2019, 11, x FOR PEER REVIEW 12 of 14
h/da 3.53 0.003 0.001 0.004 0.035
A performance index (discrepancy ratio) was also computed using the present experimental
datasets. For a predictable estimation of the difference between calculated and experimental values
of dsa/l, the discrepancy ratio is defined in Equation (5) as:
Discrepancy Ratio (DR) = 𝑙𝑜𝑔 _
_
(5)
For DR = 0, the computed values of dsa/l are identical to the experimental values of dsa/l. For
negative/positive values of discrepancy ratio, the calculated values of dsa/l is smaller/greater than the
experimental values. Accuracy is described as the frequency of cases for which the discrepancy ratio
is within a suitable range for the total number of data, as can be seen in Figure 7. Data frequency
within DR = ±0.01 is 23 out of total 32 datasets. Discrepancy ratio analysis shows good agreements
between calculated and experimental values of maximum scour depth, as can be seen in Figure 7.
Figure 7. Variation of present data frequency with discrepancy ratio.
4. Conclusions
The maximum equilibrium scour depth around a rectangular spur dike was studied
experimentally in a sand–gravel mixture bed. The influence of several parameters of flow parameters,
length of spur dike, and sediment properties on maximum equilibrium scour depth was discussed.
The comparison of time-dependent scour depths at upstream nose and wall-junction of the spur dike
was also shown and the temporal scour depth vitiation was found, which was lesser at wall-junction
compared to scour depth at the nose of spur dike. Experimentally, it was found that the maximum
scour depth at equilibrium scour condition always occurred at the upstream nose of the spur dike.
Detailed conclusions are:
1. The influence of different parameters on maximum equilibrium scour depth was discussed in
detail. The dimensionless variation of maximum equilibrium scour depth increases with
increase in U/Uca, h/da, Frsm, h/l, and decreases with increase in da/l. The scour processes in
sediment mixture are mainly influenced by the property of sediment mixture and maximum
scour depth increases with increase in densimetric sediment mixture Froude number. Therefore,
scour processes in sediment mixture increases with decrease in non-uniformity of sediment;
2. For predicting the maximum equilibrium scour depth at upstream nose of the rectangular spur
dike, the non-linear relationship in non-dimensional form was derived. This equation showed
0
5
10
15
20
-0.05 -0.04 -0.03 -0.02 -0.01 0 0.01 0.02 0.03 0.04 0.05
Datafrequency
Discrepancy ratio
Figure 7. Variation of present data frequency with discrepancy ratio.
4. Conclusions
The maximum equilibrium scour depth around a rectangular spur dike was studied experimentally
in a sand–gravel mixture bed. The influence of several parameters of flow parameters, length of spur
dike, and sediment properties on maximum equilibrium scour depth was discussed. The comparison
of time-dependent scour depths at upstream nose and wall-junction of the spur dike was also shown
and the temporal scour depth vitiation was found, which was lesser at wall-junction compared to
scour depth at the nose of spur dike. Experimentally, it was found that the maximum scour depth
at equilibrium scour condition always occurred at the upstream nose of the spur dike. Detailed
conclusions are:
1. The influence of different parameters on maximum equilibrium scour depth was discussed in
detail. The dimensionless variation of maximum equilibrium scour depth increases with increase
in U/Uca, h/da, Frsm, h/l, and decreases with increase in da/l. The scour processes in sediment mixture
13. Water 2019, 11, 1417 13 of 14
are mainly influenced by the property of sediment mixture and maximum scour depth increases
with increase in densimetric sediment mixture Froude number. Therefore, scour processes in
sediment mixture increases with decrease in non-uniformity of sediment;
2. For predicting the maximum equilibrium scour depth at upstream nose of the rectangular spur
dike, the non-linear relationship in non-dimensional form was derived. This equation showed
good agreements between computed and experimental values of scour depths, as shown in
Figure 6a–c and Tables 2 and 3;
3. A sensitivity analysis was completed to compute the most sensible parameter for maximum
equilibrium scour depth. Sensitivity analysis indicated that the maximum non-dimensional scour
depth heavily depended on densimetric sediment mixture Froude number. Secondary sensible
parameters were da/l, h/l, and h/da in Tables 2 and 3.
Author Contributions: M.P. and U.K.S. conducted experiments; M.P., M.A. and U.K.S. analysed data, applied
methodology and validated this experimental study; W.H.L., Y.C. and Z.A. revised and edited; funding acquisition
by W.H.L.
Funding: This research was funded by the Natural Science Foundation of Tianjin City: 18JCYBJC21900 and Science
Fund for Creative Research Groups of the National Natural Science Foundation of China (Grant no. 51621092).
The APC was funded by the Natural Science Foundation of Tianjin City: 18JCYBJC21900.
Acknowledgments: The authors kindly acknowledge the staff of the hydraulics laboratory, I.I.T. Roorkee, and
School of Civil Engineering, Tianjin University.
Conflicts of Interest: The authors declare no conflict of interest.
List of Notations
d Median diameter of sediment mixture
da Median diameter of armour or gravel particle
ds Median diameter of sand
d16 Particle size at 16% finer
d84 Particle size at 84% finer
dsa Maximum equilibrium scour depth
dst Scour depth at time t
Frd Densimetric Froude number
Frsm Froude number of sediment mixture
g Acceleration due to gravitational
h Flow depth
ks Roughness height
l Transverse length of spur dike
U Time-average velocity
Uca Critical velocity of armour particle
Ucs Critical velocity of sand particle
u*c Critical shear velocity
ρ Density of water
σ
Geometric standard deviation of particle size
distribution
α Absolute sensitivity
β Relative error
ω Relative sensitivity
References
1. Zhang, H.; Nakagawa, H.; Mizutani, H. Bed morphology and grain size characteristics around a spur dyke.
Int. J. Sediment Res. 2012, 27, 141–157. [CrossRef]
2. Zhang, L.; Wang, H.; Zhang, X.; Wang, B.; Chen, J. The 3-D morphology evolution of spur dike scour under
clear-water scour conditions. Water 2018, 10, 1583. [CrossRef]