staticforce analysis

1. Unit 1: Static Force Analysis
1
1
• Static force analysis
– Introduction
– Static equilibrium
– Equilibrium of two and three force members
– Members with two forces and torque
– Free body diagrams
– principle of virtual work
• Static force analysis of
– four bar mechanism
– slider-crank mechanism with and without friction.

2. STATIC EQUILIBRIUM
2
• A body is in static equilibrium if it remains in its state of rest
or motion.
• If the body is at rest, it tends to remain at rest and if in
motion, it tends to keep the motion.
• In static equilibrium,
– the vector sum of all the forces acting on the body is zero and
– the vector sum of all the moments about any arbitrary point is zero.
• Mathematically,
• In a planer system, forces can be described by two-
dimensional vectors and therefore,
2

3. EQUILIBRIUM OF TWO AND THREE-FORCE
MEMBERS
3
• A member under the action of two forces will be
in equilibrium if
– the forces are of the same magnitude,
– the forces act along the same line, and
– the forces are in opposite directions.
• Figure shows such a member.
• A member under the action of three forces will
be in equilibrium if
– the resultant of the forces is zero, and
– the lines of action of the forces intersect at a point
(known as
point of concurrency).
3

4. EQUILIBRIUM OF TWO AND THREE-FORCE MEMBERS
(Contd….)
•Figure (a) shows a member acted upon by three forces F1, F2
and F3 and is in equilibrium as the lines of action of forces
intersect at one point O and the resultant is zero.
•This is verified by adding the forces vectorially [Fig.(b)].
•As the head of the last vector F3 meets the tail of the first vector
F1, the resultant is zero.
•Figure (d) shows a case where the magnitudes and directions of
the forces are the same as before, but the lines of action of the
forces do not intersect at one point.
•Thus, the member is not in equilibrium.
4

5. • Consider a member in equilibrium in which force F1 is completely
known, F2 known in direction only and F3 completely unknown.
• The point of applications of F1 , F2 and F3 are A, B and C
respectively.
• To solve such a problem, first find the point of concurrency O from
the two forces with known directions, i.e. from F1, and F2.
• Joining O with C gives the line of action of the third force F3.
• To know the magnitudes of the forces F2 and F3, take a vector of
proper magnitude and direction to represent the force F1.
• From its two ends, draw lines parallel to lines of action of the
forces F2 and F3 forming a force triangle [Fig.].
• Mark arrowheads on F2 and F3 so that F1 , F2 and F3 are in the
same order.
5

6. MEMBER WITH TWO FORCES AND A TORQUE
6
• A member under the action of two forces and an applied
torque will be in equilibrium if
– the forces are equal in magnitude, parallel in direction and opposite in sense
and
– the forces form a couple which is equal and opposite to the applied torque.
• Figure shows a member acted upon by two equal forces F1,
and F2
and an applied torque T for equilibrium,
where T, F1 and F2 are the magnitudes of T, F1 and F2
respectively.
• T is clockwise whereas the couple formed by F1, and F2 is
counter- clockwise.

7. FORCE CONVENTION
7
• The force exerted by member i on member j is
represented by Fij
7

8. FREE BODY DIAGRAMS
8
• A free body diagram is a sketch or diagram of a part isolated
from the mechanism in order to determine the nature of forces
acting on it.
• Figure (a) shows a four-link mechanism.
• The free-body diagrams of its members 2, 3 and 4 are shown
in Figs. (b), (c) and (d) respectively.
• Various forces acting on each member are also shown.
• As the mechanism is in static equilibrium, each of its members
must be in equilibrium individually.

9. • Member 4 is acted upon by three forces F, F34 and F14.
• Member 3 is acted upon by two forces F23 and F43
• Member 2 is acted upon by two forces F32 and F12 and a torque
T.
• Initially, the direction and the sense of some of the forces may
not be known.
• Link 3 is a two-force member and for its equilibrium F23 and F43
must act along BC.
• Thus, F34 being equal and opposite to F43 also acts along BC.
9
9

10. • Assume that the force F on member 4 is known completely.
• To know the other two forces acting on this member completely,
the direction of one more force must be known.
• For member 4 to be in equilibrium, F14 passes through the
intersection of F and F34 .
• By drawing a force triangle (F is completely known), magnitudes
of F14 and F34 can be known [Fig.(e)].
Now F34 = F43 = F23 = F32
• Member 2 will be in equilibrium if F12 is equal, parallel and
opposite to F32 and
10

11. A four-link mechanism with the following dimensions is acted upon by a force
80N at angle 1500 on link DC [Fig.(a)): AD = 50 mm, AB = 40 mm, BC = 100 mm, DC =
75 mm, DE = 35 mm. Determine the input torque T on the link AB for the static
equilibrium of the mechanism for the given configuration.
11
As the mechanism is in static equilibrium, each
of its members must also be in equilibrium
individually.
Member 4 is acted upon by three forces F F34
and F14. Member 3 is acted upon by two forces
F23 and F43 Member 2 is acted upon by two
forces F32 and F12 and a torque T.
Initially, the direction and the sense of some of
the forces are not known.
Force F on member 4 is known completely. To
know the other two forces acting on this
member completely, the direction of one more
force must be known. To know that, link 3 will
have to be considered first which is a two-force
member.

12. 6/19/201
5
• As link 3 is a two-force member [Fig.(b)], for its equilibrium, F23
and F43 must act along BC (at this stage, the sense of direction
of forces F23 and F43 is not known). Thus, the line of action of
F34 is also along BC.
• As force F34 acts through point C on link 4, draw a line parallel
to BC through C by taking a free body of link 4 to represent the
same. Now, as link 4 is three force member, the third force F14
passes through the intersection of F and F34 [Fig (c)].
• By drawing a force triangle (F is completely known),
magnitudes of F14 and F34 are known [Fig(d)].
From force triangle, F34 = 47.8 N
12

13. • Now, F34 = -F43
=F23 = -F32
13
• Member 2 will be in equilibrium [Fig. (e)] if F12 is equal, parallel
and opposite to F32 and
T=-F32 x h = 47.8 x 39.3 = -1878.54 N.mm The input torque has
to be equal and opposite to this couple i.e. T= 1878.5 N/mm
(clockwise)
h=Perpendicular distance between two equal and opposite
forces.

14. Figure shows a slider crank mechanism in which the resultant gas pressure 8x104 N/m2 acts
on the piston of cross sectional area 0.1m2 The system is kept in equilibrium as a result of
the couple applied to the crank 2, through the shaft at O2. Determine forces acting on all the
links (including the pins) and the couple on 2. OA=100mm, AB=450mm.
14

15. Force triangle for the forces acting on(4)is drawn to some suitable scale.
Magnitude and direction of P known and lines of action of F34 & F14
known.
Measure the lengths of vectors and multiply by the scale factor to get the
magnitudes of F14 & F34.
Directions are also fixed.
Since link 3 is acted upon by only two forces, F43 and F23
are collinear, equal in magnitude and opposite in
direction i.e., F43 = -F23 =8.8xl03 N
Also,F23 = - F32 (equal in magnitude and opposite in
direction).
15
15

16. Link 2 is acted upon by 2 forces and a torque, for equilibrium
the two forces must be equal, parallel and opposite and their
sense must be opposite to T2.
There fore,
F32 = -F12 =8.8xl03 N
F32 & F12 form a counter clock wise couple of magnitude, F23
* h = F12 *h
=(8.8xl03)x0.125 = 1100 Nm.
To keep 2 in equilibrium, T: should act clockwise and
magnitude is 1100 Nm.
Note: h is measured perpendicular to F32 &F12
16