Rev 00. 10 ways for working safety @ heights poster 30 july-2018
•Download as PPTX, PDF•
0 likes•421 views
10 Ways For Working Safely @ Heights 1 Install full edge protection 2 Barricade off danger area below 3 Be trained to work at heights 4 Don’t enter unsafe platforms 5 Check “scaff-tag” are green 6 Harness your tools 7 Hooks on safety harness 8 se podium platforms & not step ladder 9 Use both hands don’t’ carry anything up-down ladders 10 Don’t work alone Engineers, Supervisors & HSE must always “Look Up” at every opportunity
Report
Share
Report
Share
Recommended
NGI-Authorized Gas Testing
- The document discusses gas testing procedures and guidelines for authorized gas testers. It outlines the importance of testing for toxic, explosive, and oxygen levels before and during work to ensure workplace safety.
- Only those who have completed authorized gas tester training can certify gas tests and ensure environments are safe for work in places like confined spaces where gases may accumulate.
- Proper gas detection equipment must be used and calibrated regularly, and comprehensive atmospheric testing is required before entry into any confined space to check for hazards like low oxygen, toxic gases, and explosive gases from various sources.
Working at-height
The document defines work at height as any work performed 1.8 meters or more above ground level, including below ground. Work above 1.8 meters requires a permit and safety checklist. Fall distances increase rapidly with time, emphasizing the need for fall protection like railings, safety harnesses attached to lifelines, and safety nets. Proper planning, equipment, and rescue procedures are required for working at heights.
Lifting Operation Safety ppt.pptx
This document discusses safe lifting practices and requirements. It defines routine and non-routine lifts and lists potential hazards. Key requirements include developing a lifting plan, appointing competent supervisors, inspecting equipment, and defining roles for crane operators, riggers, and signal persons. Specific safe practices are outlined for preparing loads, attaching slings, and storing/maintaining equipment. Personnel must be trained and lifts must not endanger workers or exceed equipment ratings.
Working at heights
The document provides an overview of safety procedures for working at heights. It discusses ladder safety, fall protection equipment like harnesses and lanyards, scaffolding safety, and mobile elevated work platforms. It emphasizes the importance of fall protection, noting that falls are the leading cause of construction fatalities and that workers should be protected from falls of 2 meters or more.
Constrution site
This handbook provides construction site workers with guidance on occupational safety and health. It outlines legal responsibilities and covers topics like keeping work areas tidy, using equipment safely, emergency response, personal protective equipment, and hygiene. The goal is to help prevent accidents by promoting safe work practices and awareness of hazards. Workers are advised to cooperate with safety rules and report any issues to supervisors.
Working at height slides
The document provides information about working at heights training, including:
- The aims are to provide personnel working at heights with practical knowledge and application of safe practices to prevent injury.
- The objectives include identifying fall regulations and risks, demonstrating safety equipment use, and emergency response procedures.
- It discusses examples of working at heights, regulations and responsibilities to control fall risks, and the goals of reducing falls injuries.
BANKSMAN TRAINING.ppt
This document provides guidance for flagmen/banksmen in construction. It outlines that a flagman assists equipment operators by signaling safe movements, controls traffic and people near operating equipment, and acts as the operator's eyes where they cannot see. Key responsibilities of a flagman include inspecting equipment, reporting defects, following safety procedures, restricting access to work areas, keeping escape routes clear, and communicating with operators. The document emphasizes that a flagman must always remain in plain view of operators and stop operations immediately if any danger is observed.
bar bending safety precautions.pdf
Bar bending machines consist of an electric motor, gearbox, and extended shaft to bend rebar. There are different types including portable, electric, hydraulic, and automatic benders. Proper operation of bending machines requires training operators, inspecting the machine, keeping the work area clean, and using safety equipment. Operators should not exceed the machine's capacity, operate without safety guards, or place body parts near moving parts to avoid injury. Following manufacturers' safety instructions and wearing protective equipment can help safely operate bar bending machines.
Recommended
NGI-Authorized Gas Testing
- The document discusses gas testing procedures and guidelines for authorized gas testers. It outlines the importance of testing for toxic, explosive, and oxygen levels before and during work to ensure workplace safety.
- Only those who have completed authorized gas tester training can certify gas tests and ensure environments are safe for work in places like confined spaces where gases may accumulate.
- Proper gas detection equipment must be used and calibrated regularly, and comprehensive atmospheric testing is required before entry into any confined space to check for hazards like low oxygen, toxic gases, and explosive gases from various sources.
Working at-height
The document defines work at height as any work performed 1.8 meters or more above ground level, including below ground. Work above 1.8 meters requires a permit and safety checklist. Fall distances increase rapidly with time, emphasizing the need for fall protection like railings, safety harnesses attached to lifelines, and safety nets. Proper planning, equipment, and rescue procedures are required for working at heights.
Lifting Operation Safety ppt.pptx
This document discusses safe lifting practices and requirements. It defines routine and non-routine lifts and lists potential hazards. Key requirements include developing a lifting plan, appointing competent supervisors, inspecting equipment, and defining roles for crane operators, riggers, and signal persons. Specific safe practices are outlined for preparing loads, attaching slings, and storing/maintaining equipment. Personnel must be trained and lifts must not endanger workers or exceed equipment ratings.
Working at heights
The document provides an overview of safety procedures for working at heights. It discusses ladder safety, fall protection equipment like harnesses and lanyards, scaffolding safety, and mobile elevated work platforms. It emphasizes the importance of fall protection, noting that falls are the leading cause of construction fatalities and that workers should be protected from falls of 2 meters or more.
Constrution site
This handbook provides construction site workers with guidance on occupational safety and health. It outlines legal responsibilities and covers topics like keeping work areas tidy, using equipment safely, emergency response, personal protective equipment, and hygiene. The goal is to help prevent accidents by promoting safe work practices and awareness of hazards. Workers are advised to cooperate with safety rules and report any issues to supervisors.
Working at height slides
The document provides information about working at heights training, including:
- The aims are to provide personnel working at heights with practical knowledge and application of safe practices to prevent injury.
- The objectives include identifying fall regulations and risks, demonstrating safety equipment use, and emergency response procedures.
- It discusses examples of working at heights, regulations and responsibilities to control fall risks, and the goals of reducing falls injuries.
BANKSMAN TRAINING.ppt
This document provides guidance for flagmen/banksmen in construction. It outlines that a flagman assists equipment operators by signaling safe movements, controls traffic and people near operating equipment, and acts as the operator's eyes where they cannot see. Key responsibilities of a flagman include inspecting equipment, reporting defects, following safety procedures, restricting access to work areas, keeping escape routes clear, and communicating with operators. The document emphasizes that a flagman must always remain in plain view of operators and stop operations immediately if any danger is observed.
bar bending safety precautions.pdf
Bar bending machines consist of an electric motor, gearbox, and extended shaft to bend rebar. There are different types including portable, electric, hydraulic, and automatic benders. Proper operation of bending machines requires training operators, inspecting the machine, keeping the work area clean, and using safety equipment. Operators should not exceed the machine's capacity, operate without safety guards, or place body parts near moving parts to avoid injury. Following manufacturers' safety instructions and wearing protective equipment can help safely operate bar bending machines.
Safety while sandblasting
http://sandblaster-parts.com/?gclid=CNSIx_2P-cQCFQSUfgodjxIAWA | Safety is critical in any field, but especially a key factor of importance for sandblasting jobs. Our presentations will teach you how to protect yourself from harm on the job.
Standard Operating Practices (SOPs) and Standard Maintenance Practices (SMPs)...
1. The document provides operating rules for crane operators, outlining proper procedures for safely lifting and moving loads.
2. Key rules include centering the crane over the load before lifting, operating the crane smoothly, keeping lifting ropes vertical, ensuring the area is clear before lifting, and checking that loads are lifted high enough to clear obstructions.
3. Operators are instructed to test hoist brakes with near capacity loads, secure slings and hooks properly, avoid overloading the crane, and follow shutdown procedures by raising hooks, parking in designated locations, and turning all controls off before leaving the crane.
Forklift Safety Tips: Do's and Don'ts
Forklifts can be dangerous: they account for 25% of injuries at work. Many workplace accidents involve people being hit or run over by forklift trucks (typically when the forklift is reversing)because the driver did not see them. Owing to their size and weight, injuries resulting from forklifts are generally very serious. Accidents involving them are often caused by poor supervision and a lack of training. The following forklift safety tips will help you and those you work with stay safe around forklifts. Thanks to the Health and Safety Authority.
Aerial and scissor lift safety 2
This document provides guidance on aerial lift and scissor lift safety according to OSHA standards. It discusses OSHA regulations covering aerial and scissor lifts, types of lifts, training requirements, inspections, safety procedures, fall protection requirements, and shutdown procedures. Training is required and must cover hazards, fall protection systems, operating and maintaining the specific lift, and other safety topics. Proper inspection and safety procedures, such as following manufacturer guidelines for capacity and fall protection, are critical for safe lift operation.
Hot Works Safety Training
CONTENTS:
I. What is a Hot Work ?
II. Training
III. PPE`s
IV. Hot Work Permit
V. Electric Welding
VI. Fire Prevention
VII. Fire Watch
VIII. Generator Sets
IX. Welding Equipment Checks
X. Oxy Cutting Equipment
XI. Fire Safety Precautions
XII. Compressed Gas Cylinders
XIII. Safe Practices
XIV. Heat Stress
Safety harness - fall protection - Wessam Atif
A brief presentation on how and when to use fall arrest system, how to don full body harness, when to use shock absorber and what to do if someone falls while wearing harness and lanyard to rescue them. Dr. Wessam Atif.
Rescue at heights westfields 2017
The document provides guidance on developing rescue procedures for working at heights. It outlines key considerations for an emergency response plan including training, creating a plan, and rescue procedures. The procedures describe different rescue methods from elevated platforms, ladders, the work area below, or using a basket if other options are not possible. Basket rescues require specific safety equipment and protocols. Post-rescue duties include accident investigation and modifying plans as needed. Rescue training is also important for tower crane operators due to the urgency of such rescues.
Nylon Web Slings Inspection Checklist
Lifting slings made from nylon are the most common and versatile styles of slings. Since they can be used in many lifting applications there are several types of damage that can occur.
Our inspection and check list will not only describe the types of damage but will give tips to prevent damage.
Pre commissioning and Commissioning Safety.pdf
Pre-commissioning activities such as cleaning pipes through methods like chemical cleaning, water flushing, and air blowing are meant to prepare systems for commissioning. Commissioning brings systems to an operational state through tests like leak tests and catalyst loading. Both pre-commissioning and commissioning involve hazards like chemicals, electricity, asphyxiation, and rotating equipment that require controls like permits, isolation, PPE, and trained workers for safety.
Presentation working at height
Working at height remains a major cause of injuries and fatalities. Employers must properly plan work at height, use the right equipment, and provide fall protection training to competent workers. Simple precautions like performing work from ladders safely and avoiding fragile surfaces can reduce risks. Workers should avoid working at unprotected heights whenever possible.
Safe Operations of Cranes, Hoists and Truck Hoists by Reagan Safety
This document outlines safety requirements and procedures for operating cranes, hoists, and truck hoists. It discusses general requirements such as inspections, qualifications for operators, and load ratings. It provides details on inspection types and frequencies. Operational procedures address qualified operators, pre-use checks, lifting loads, and parking equipment. Additional requirements specific to truck hoists include load ratings, inspections, safety tips, and precautions for their safe operation. The overall goal is to maintain a safe workplace by ensuring only qualified individuals operate this lifting equipment according to proper procedures.
21 confined space working risk assessment templates
This risk assessment document evaluates the hazards associated with confined space work. It identifies risks such as exposure to live underground utilities, toxic gases, flooding, and restricted evacuation. Initial risks are rated as high. Control measures are outlined to reduce risks, such as obtaining permits, gas monitoring, ventilation, restricted hot works, lifelines, and rescue drills. Residual risks are rated as low when all controls are followed. Additional measures like supervisor monitoring and calibrated gas detectors are recommended to ensure safety protocols are strictly adhered to for confined space work.
Man and machine interface
Man and Machine Interface
Working around heavy equipment can be extremely dangerous. Too many workers are killed each year when they are run over or struck by these pieces of machinery. It’s important to know the safety precautions to take when working in the vicinity of heavy equipment such as dump trucks, front-end loaders, cranes, Excavator, Bob Cat, Forklift, Concrete Mixture Truck, other heavy trucks/Equipment's, etc.
Lifting & procedure
The document discusses lifting equipment and procedures as outlined in the Factories Act. It defines key terms like competent person, machinery, and lifting tackles. It provides guidelines for planning lifts, conducting the lift, landing loads, and dos and don'ts. It also examines sling angles and their effect on safe working loads. Case studies describe incidents where improper planning and techniques like misaligned loads led to injuries.
Hand and Power Tool Safety by Haylor
This document provides an overview of hand and power tool safety. It discusses the responsibilities of employers to provide safe tools and train employees, as well as employee responsibilities to follow safe practices. Basic safety rules are outlined, such as using the proper tool for the job, wearing PPE, and keeping tools maintained and stored safely. Hazards associated with different types of tools are explained, along with the importance of machine guarding and avoiding moving parts. The document also covers electrical, pneumatic, and powder-actuated tools, outlining precautions for each.
Rebar cutting hazards
This document discusses hazards associated with rebar cutting and bending machines, chop saw machines, and provides precautions for safe operation. Key hazards include injury from machine parts, flying debris, electrical shock, and improper or unsafe machine operation. Safe operation requires proper training, use of machine guards, protective equipment, following maintenance procedures, and not overriding safety devices. Operators should feed material smoothly, avoid contact with cutting wheels, and not make unsupported or awkward cuts.
Lifting & Rigging Safety.pptx
The document provides guidance on safety procedures for lifting operations using cranes and rigging equipment. Some key points include:
- Proper planning of lifting operations, selection of suitable cranes and equipment, maintenance, training of personnel, and supervision are essential for safety.
- Cranes must be set up correctly with outriggers fully extended on level, stable ground before heavy lifts.
- Rigging such as slings and shackles must be inspected and rated for the load, with the load balanced and secured above its center of gravity.
- Personnel must stand clear of lifts and be protected from potential hazards during the operation.
- Guidelines are provided for safe practices regarding crane operation
Job Safety Analysis For Lifting Activity By Crane | JSA | Gaurav Singh Rajput
Job Safety Analysis For Lifting Activity By Crane | Gaurav Singh Rajput | TBRA | JSA | Risk Assessment
Scaffolding safety training.ppt
This document provides information on scaffold safety training. It aims to improve participants' skills in scaffolding safety requirements and transfer technical knowledge about scaffolding safety practices. The objectives are to make participants familiar with international scaffolding standards, scaffold components, hazards of erecting and dismantling scaffolds, and roles and responsibilities of scaffold supervisors. It also discusses common causes of scaffolding disasters and accidents, as well as personal protective equipment requirements.
Visitors SHE Induction Presentation 2016
The document provides an induction for a construction site. It summarizes the following key points in 3 sentences:
The document outlines the legal health and safety requirements for the construction site, including providing training and ensuring workers use proper protective equipment. It also details various hazards on site like working at heights, electricity, and chemicals. The induction covers emergency procedures, incident reporting, and use of personal protective equipment like hard hats and safety shoes.
5 - CLOWNS BELONG IN THE CIRCUS & NOT ON THE JOB.pdf
5 - CLOWNS BELONG IN THE CIRCUS & NOT ON THE JOB
More Related Content
What's hot
Safety while sandblasting
http://sandblaster-parts.com/?gclid=CNSIx_2P-cQCFQSUfgodjxIAWA | Safety is critical in any field, but especially a key factor of importance for sandblasting jobs. Our presentations will teach you how to protect yourself from harm on the job.
Standard Operating Practices (SOPs) and Standard Maintenance Practices (SMPs)...
1. The document provides operating rules for crane operators, outlining proper procedures for safely lifting and moving loads.
2. Key rules include centering the crane over the load before lifting, operating the crane smoothly, keeping lifting ropes vertical, ensuring the area is clear before lifting, and checking that loads are lifted high enough to clear obstructions.
3. Operators are instructed to test hoist brakes with near capacity loads, secure slings and hooks properly, avoid overloading the crane, and follow shutdown procedures by raising hooks, parking in designated locations, and turning all controls off before leaving the crane.
Forklift Safety Tips: Do's and Don'ts
Forklifts can be dangerous: they account for 25% of injuries at work. Many workplace accidents involve people being hit or run over by forklift trucks (typically when the forklift is reversing)because the driver did not see them. Owing to their size and weight, injuries resulting from forklifts are generally very serious. Accidents involving them are often caused by poor supervision and a lack of training. The following forklift safety tips will help you and those you work with stay safe around forklifts. Thanks to the Health and Safety Authority.
Aerial and scissor lift safety 2
This document provides guidance on aerial lift and scissor lift safety according to OSHA standards. It discusses OSHA regulations covering aerial and scissor lifts, types of lifts, training requirements, inspections, safety procedures, fall protection requirements, and shutdown procedures. Training is required and must cover hazards, fall protection systems, operating and maintaining the specific lift, and other safety topics. Proper inspection and safety procedures, such as following manufacturer guidelines for capacity and fall protection, are critical for safe lift operation.
Hot Works Safety Training
CONTENTS:
I. What is a Hot Work ?
II. Training
III. PPE`s
IV. Hot Work Permit
V. Electric Welding
VI. Fire Prevention
VII. Fire Watch
VIII. Generator Sets
IX. Welding Equipment Checks
X. Oxy Cutting Equipment
XI. Fire Safety Precautions
XII. Compressed Gas Cylinders
XIII. Safe Practices
XIV. Heat Stress
Safety harness - fall protection - Wessam Atif
A brief presentation on how and when to use fall arrest system, how to don full body harness, when to use shock absorber and what to do if someone falls while wearing harness and lanyard to rescue them. Dr. Wessam Atif.
Rescue at heights westfields 2017
The document provides guidance on developing rescue procedures for working at heights. It outlines key considerations for an emergency response plan including training, creating a plan, and rescue procedures. The procedures describe different rescue methods from elevated platforms, ladders, the work area below, or using a basket if other options are not possible. Basket rescues require specific safety equipment and protocols. Post-rescue duties include accident investigation and modifying plans as needed. Rescue training is also important for tower crane operators due to the urgency of such rescues.
Nylon Web Slings Inspection Checklist
Lifting slings made from nylon are the most common and versatile styles of slings. Since they can be used in many lifting applications there are several types of damage that can occur.
Our inspection and check list will not only describe the types of damage but will give tips to prevent damage.
Pre commissioning and Commissioning Safety.pdf
Pre-commissioning activities such as cleaning pipes through methods like chemical cleaning, water flushing, and air blowing are meant to prepare systems for commissioning. Commissioning brings systems to an operational state through tests like leak tests and catalyst loading. Both pre-commissioning and commissioning involve hazards like chemicals, electricity, asphyxiation, and rotating equipment that require controls like permits, isolation, PPE, and trained workers for safety.
Presentation working at height
Working at height remains a major cause of injuries and fatalities. Employers must properly plan work at height, use the right equipment, and provide fall protection training to competent workers. Simple precautions like performing work from ladders safely and avoiding fragile surfaces can reduce risks. Workers should avoid working at unprotected heights whenever possible.
Safe Operations of Cranes, Hoists and Truck Hoists by Reagan Safety
This document outlines safety requirements and procedures for operating cranes, hoists, and truck hoists. It discusses general requirements such as inspections, qualifications for operators, and load ratings. It provides details on inspection types and frequencies. Operational procedures address qualified operators, pre-use checks, lifting loads, and parking equipment. Additional requirements specific to truck hoists include load ratings, inspections, safety tips, and precautions for their safe operation. The overall goal is to maintain a safe workplace by ensuring only qualified individuals operate this lifting equipment according to proper procedures.
21 confined space working risk assessment templates
This risk assessment document evaluates the hazards associated with confined space work. It identifies risks such as exposure to live underground utilities, toxic gases, flooding, and restricted evacuation. Initial risks are rated as high. Control measures are outlined to reduce risks, such as obtaining permits, gas monitoring, ventilation, restricted hot works, lifelines, and rescue drills. Residual risks are rated as low when all controls are followed. Additional measures like supervisor monitoring and calibrated gas detectors are recommended to ensure safety protocols are strictly adhered to for confined space work.
Man and machine interface
Man and Machine Interface
Working around heavy equipment can be extremely dangerous. Too many workers are killed each year when they are run over or struck by these pieces of machinery. It’s important to know the safety precautions to take when working in the vicinity of heavy equipment such as dump trucks, front-end loaders, cranes, Excavator, Bob Cat, Forklift, Concrete Mixture Truck, other heavy trucks/Equipment's, etc.
Lifting & procedure
The document discusses lifting equipment and procedures as outlined in the Factories Act. It defines key terms like competent person, machinery, and lifting tackles. It provides guidelines for planning lifts, conducting the lift, landing loads, and dos and don'ts. It also examines sling angles and their effect on safe working loads. Case studies describe incidents where improper planning and techniques like misaligned loads led to injuries.
Hand and Power Tool Safety by Haylor
This document provides an overview of hand and power tool safety. It discusses the responsibilities of employers to provide safe tools and train employees, as well as employee responsibilities to follow safe practices. Basic safety rules are outlined, such as using the proper tool for the job, wearing PPE, and keeping tools maintained and stored safely. Hazards associated with different types of tools are explained, along with the importance of machine guarding and avoiding moving parts. The document also covers electrical, pneumatic, and powder-actuated tools, outlining precautions for each.
Rebar cutting hazards
This document discusses hazards associated with rebar cutting and bending machines, chop saw machines, and provides precautions for safe operation. Key hazards include injury from machine parts, flying debris, electrical shock, and improper or unsafe machine operation. Safe operation requires proper training, use of machine guards, protective equipment, following maintenance procedures, and not overriding safety devices. Operators should feed material smoothly, avoid contact with cutting wheels, and not make unsupported or awkward cuts.
Lifting & Rigging Safety.pptx
The document provides guidance on safety procedures for lifting operations using cranes and rigging equipment. Some key points include:
- Proper planning of lifting operations, selection of suitable cranes and equipment, maintenance, training of personnel, and supervision are essential for safety.
- Cranes must be set up correctly with outriggers fully extended on level, stable ground before heavy lifts.
- Rigging such as slings and shackles must be inspected and rated for the load, with the load balanced and secured above its center of gravity.
- Personnel must stand clear of lifts and be protected from potential hazards during the operation.
- Guidelines are provided for safe practices regarding crane operation
Job Safety Analysis For Lifting Activity By Crane | JSA | Gaurav Singh Rajput
Job Safety Analysis For Lifting Activity By Crane | Gaurav Singh Rajput | TBRA | JSA | Risk Assessment
Scaffolding safety training.ppt
This document provides information on scaffold safety training. It aims to improve participants' skills in scaffolding safety requirements and transfer technical knowledge about scaffolding safety practices. The objectives are to make participants familiar with international scaffolding standards, scaffold components, hazards of erecting and dismantling scaffolds, and roles and responsibilities of scaffold supervisors. It also discusses common causes of scaffolding disasters and accidents, as well as personal protective equipment requirements.
Visitors SHE Induction Presentation 2016
The document provides an induction for a construction site. It summarizes the following key points in 3 sentences:
The document outlines the legal health and safety requirements for the construction site, including providing training and ensuring workers use proper protective equipment. It also details various hazards on site like working at heights, electricity, and chemicals. The induction covers emergency procedures, incident reporting, and use of personal protective equipment like hard hats and safety shoes.
What's hot (20)
Standard Operating Practices (SOPs) and Standard Maintenance Practices (SMPs)...
Standard Operating Practices (SOPs) and Standard Maintenance Practices (SMPs)...
Safe Operations of Cranes, Hoists and Truck Hoists by Reagan Safety
Safe Operations of Cranes, Hoists and Truck Hoists by Reagan Safety
21 confined space working risk assessment templates
21 confined space working risk assessment templates
Job Safety Analysis For Lifting Activity By Crane | JSA | Gaurav Singh Rajput
Job Safety Analysis For Lifting Activity By Crane | JSA | Gaurav Singh Rajput
More from Dwarika Bhushan Sharma
5 - CLOWNS BELONG IN THE CIRCUS & NOT ON THE JOB.pdf
5 - CLOWNS BELONG IN THE CIRCUS & NOT ON THE JOB
3-STOP FALLS, CLEAN UP, PICK UP, WIPE UP.pdf
3-STOP FALLS, CLEAN UP, PICK UP, WIPE UP3-STOP FALLS, CLEAN UP, PICK UP, WIPE UP-STOP FALLS, CLEAN UP, PICK UP, WIPE UP
2-THERE'S A SAFE WAY TO DO EVERY JOB, OF YOU DON'T KNOW ASK.pdf
2-THERE'S A SAFE WAY TO DO EVERY JOB, OF YOU DON'T KNOW ASK 2-THERE'S A SAFE WAY TO DO EVERY JOB, OF YOU DON'T KNOW ASK
1-HAZARDOUS CHEMICALS.pdf
This document provides the name of a company but no other details. It contains only the words "Company Name" with no other context or information provided. In just two words, the document states the name of a company without any other descriptive text.
PRE-START BRIEFING Form # HSEQ - PSB Rev 2 -.docx
Project Information:
Project Name:
Location: Supervisor :
Company name : Date:
Task Description:
Before work starts, the following must be in place
Induction Supervision Test Certificates Communication in same language Method Statement Risk Assessment Permit To Work Area Lighting
SELECT HAZARDS SELECT CONTROLS
( Tick to identify the controls in place)
Fall from height Training Access Ladder Access Handrail Edge Protection Secure Ladder Adequate Work Platform Guards for Openings Safety Harness Life Lines
Others( Specify)
Manual Handling Training Check Weight Mechanical Aids Access Route Team Lifting Wrong method Right Method
Power tools Training Color code inspection tag Check Cable Wheel guards Safe plug & sockets Cable Protection Proper Scaffold Cable Overhead Rotatory part guards
Scaffold Scaffold Tag Edge Protection Check Overhead works Access Ladder Adequate Work Platform Weather condition Out riggers Ladder 3 feet above platform Safety Harness
SELECT HAZARDS SELECT CONTROLS
( Tick to identify the controls in place)
Risk Assessment
Lifting Plan Tag Lines Lifting points / hooks Banks man Load stability Check Lifting gear Examination /Inspection Sharp edges protected
Lifting operations Weather/ Wind Speed Ground conditions Exclusion zone Communication Loading/ unloading vehicles Spreader Beams Check Ground conditions Check outriggers Others
Fire Fire Extinguisher Fire Hose Fire Exit Assembly point others
Slip/Trip Clean before you go Barricade the waste Waste Management Clean Access Housekeeping Clean liquid spillage Access signs Maintain access/ Egress
PPE
Safety Harness
Safety Helmet Coveralls Hi vis Jacket Safety Shoe Face Shield Ear Protection
Dust mask Respiratory Equipment Life line/ harness anchorage Hand Gloves Goggles/ Glass
Pre start Briefing done by: Signature:
Reviewed By HSE Manager/ In charge: Signature:
FIRE PREVENTION REQUIREMENTS Form # HSEQ - Rev 2.docx
Code of Practice
C.O.P # 01
Fire Prevention Requirements
(Management of Combustible Materials & Electrical Inspections)
Rev. 01, Mar 23
SUB CONTRACTORS HSE CHECKLIST Form # HSEQ - SPSC Rev 2 -.docx
This document is a sub-contractor pre-start HSE checklist that must be filled out daily before starting any activity. It collects project information, task details including description, location, workers and duration. It also checks that various HSE prerequisites are in place such as safety inductions, risk assessments, PPE availability, inspection of tools and equipment, and that unsafe conditions have been rectified. The sub-contractor must acknowledge that all precautions and control measures have been taken and the workers have been deemed competent to perform the task safely.
STORE INSPECTION Form # HSEQ - Form 2 Rev 2.docx
Project Information
Project Name: Store No.
Location: Contact Person:
Company Name: Arabtec Construction LLC. Date:
Sr. Description Yes No N/A Comments
1. Is access to stores are restricted to authorized personnel only?
2. Are there clear spaces around racks and stacks of stored materials and are adequate gangways provided between them?
3. Are stacks and storage kept clear of light fittings and hot surfaces?
4. Are all stocks of flammable liquids kept in purpose-built flammable storage liquid stores?
5. Are storage areas generally cleaned and tidy?
6. Are flammable liquids kept away from all possible sources of ignition?
7. Emergency exit signs are available in right locations
8. Smoke detectors/fire alarm are visible and accessible.
9. Fire extinguishers are available are serviced regularly
10. Are free standing shelves and cupboards secured for stability?
11. Are heavy items stored at a suitable height?
12. Are chemical containers used for storage suitable and clearly labelled?
13. Is there adequate light in the storage area?
14. Are all small loose items secured in appropriate storage?
15. Are warning notices, prohibiting smoking and naked lights prominently displayed?
16. Others if any:
Remarks:
Inspected by: Signature:
Reviewed by Project Manager/HSE Manager Signature:
WITNESS STATEMENT FORM.docx
This document records a statement for a project located at an unspecified location. The statement is provided and written by an individual who acknowledges that the information is true to the best of their recollection. The individual provides their name, signature, position and date at the end of the statement.
PROJECT LEADER INCIDENT BRIEFING Form # HSEQ - PLIB Rev 2 -.docx
1. Project Information:
Project Name: Click here to enter text.
Report No.: Click here to enter text.
Project Location: Click here to enter text.
Property No.: Click here to enter text.
☐ Fatality ☐ Major Injury ☐ Minor Injury ☐ Property Damage ☐ Environmental ☐ Other
2. Describe the Incident in detail:
Answer who, what, why, where, when & how in this section: (Attach additional pages if required)
3. Incident Root Causes:
Describe direct, indirect & root cause: (Attach additional pages if required)
4. Key Corrections Taken Immediately after the Incident:
Attach additional pages if more space is required:
5. Key Corrective Actions to Prevent Recurrence:
Describe the corrective actions with timeframe: (Attach additional pages if required)
Corporate Office Remarks:
HSE FORMS (COVER PAGE)2 Form # HSEQ - Rev 2.docx
This document pertains to health, safety, environment, and quality forms from an HSEQ department. The HSEQ department handles forms related to health, safety, environment, and quality assurance. No other details are provided about the specific forms or purpose of the HSEQ department.
LIFT SHAFT ENTRY PERMIT Form # HSEQ - LSEP Rev 2 -.docx
1. Project Information: (To be filled by initiator/originator)
Project Name: Permit No.:
Project Location:
Requesting Contractor/Company
2. Permit Issuance Details: (To be filled by initiator/originator)
THIS PERMIT IS ONLY FOR ONE SHIFT AND NOT EXTENDABLE
Description of Task:
Detail of Surroundings:
Permit Validity:
Time (from): __________Hrs.
Time (To): __________Hrs.
Date:
3. Control Measures: (To be filled by initiator/originator and verified by Evaluator)
Checks Yes-No-NA Checks Yes-No-NA
Method statement & Risk assessment developed, approved & communicated? ☐ ☐ ☐
Availability of rescue procedure and equipment? ☐ ☐ ☐
Operatives are trained and competent? ☐ ☐ ☐
Workplace appropriately illuminated ☐ ☐ ☐
Any high risk activity associated that requires PTW (i.e. hot work, CSE)? ☐ ☐ ☐
Forced ventilation provided? ☐ ☐ ☐
Are all necessary Permit approved and displayed at work location? ☐ ☐ ☐
Means of communication available? (Mobile, radio etc.) ☐ ☐ ☐
Safe access / Working Platform provided? ☐ ☐ ☐
Mandatory/specific good condition PPEs are available ☐ ☐ ☐
Availability of barricades/protection to prevent unauthorized or accidental entry? ☐ ☐ ☐
Life Line provided? ☐ ☐ ☐
Warning signs posted? ☐ ☐ ☐
Fall Protection equipment (e.g. full body harness) available? ☐ ☐ ☐
Availability of Fall protection arrangement? ☐ ☐ ☐
Other(s): ☐ ☐ ☐
Adequate Lighting provided? ☐ ☐ ☐
☐ ☐ ☐
4. Acknowledgement by Initiator and Evaluator:
☐ Acknowledge that all above precautions have been taken. These have also been fully explained to the operatives, and I consider them competent to do it safely.
Initiator/Originator Name: Designation:
Signature: Time:
☐ Acknowledge that I have checked above control measures and consider the work area safe to carry out the activity
Evaluator (HSE Team): Designation:
Signature: Time
Comments (if any):
5. Authorization (PM/CM):
Name: Designation:
Signature: Time:
6. Completion/Cancelation of Permit:
☐ Acknowledge that the area have been restored to a safe and orderly condition.
Initiator Signature: Time:
☐ Acknowledge that I have checked the area and been restored to a safe and orderly condition.
Evaluator Signature: Time:
LIVE ELECTRICAL WORK PERMIT Form # HSEQ - LEP Rev 2.docx
1. Project Information: (To be filled by initiator/originator)
Project Name: Permit No.:
Project Location:
Requesting Contractor/Company
2. Permit Issuance Details: (To be filled by initiator/originator)
THIS PERMIT IS ONLY FOR ONE SHIFT AND NOT EXTENDABLE
Description of Task:
Location / Area :
Panel No : Voltage:
Permit Validity:
Time (from): _______Hrs.
Time (To): __________Hrs.
Date:
3. Prerequisites: (To be filled by initiator/originator and verified by Evaluator)
No: Checks Yes-No-NA Checks Yes-No-NA
ENERGIZATION (“Power On”) ISOLATION (“Power Off”)
1. Safety tool box briefing done. ☐ ☐ ☐
Method statement/Risk assessment in place. ☐ ☐ ☐
2. Authorized personnel / operators available. ☐ ☐ ☐
Authorized personnel / operators available. ☐ ☐ ☐
3. Method statement/Risk assessment in place. ☐ ☐ ☐
Adjacent live areas protected. ☐ ☐ ☐
4. Safety Barriers in place and safety signage Displayed. ☐ ☐ ☐
PPE available, high voltage rubber gloves, Safety goggles and floor mat. ☐ ☐ ☐
5. Working area is well lighted. ☐ ☐ ☐
Isolation/Lock-out in place. ☐ ☐ ☐
6. Electrical instruments are available for any Purpose. ☐ ☐ ☐
Electrical circuits “proved” by calibrated Instrument and found out to be no power. ☐ ☐ ☐
7. Correct PPE available, high voltage rubber Gloves, safety goggles and floor mat. ☐ ☐ ☐
Unauthorized workers are cleared from the Area. ☐ ☐ ☐
8. Approved WIR for installation, testing and Termination are attached to the permit. ☐ ☐ ☐
Standby operatives in the event of contact With live circuits. ☐ ☐ ☐
9. Emergency light (Flashlight) available. ☐ ☐ ☐
Emergency light (Flashlight) available. ☐ ☐ ☐
10. Is live work absolutely necessary? ☐ ☐ ☐
Emergency response plan available ☐ ☐ ☐
11. Unauthorized workers are cleared from the area.
☐ ☐ ☐
Other ( Specify): ☒ ☐ ☐
12. Power cable route from panel board to plant & equipment has been checked ☐ ☐ ☐
13 Emergency response plan available ☐ ☐ ☐
14 Other ( Specify): ☐ ☐ ☐
4. Acknowledgement by Initiator and Evaluator:
☐ Acknowledge that all above precautions have been taken. These have also been fully explained to the operatives, and I consider them competent to do it safely.
Initiator/Originator Name: Designation:
Signature: Date /Time:
☐ Acknowledge that I have checked above control measures and consider the work area safe to carry out the activity
Evaluator (HSE Team): Designation:
Signature: Date /Time
Comments (if any):
5. Authorization (PM/CM):
Name: Designation:
Signature: Date /Time:
6. Completion/Cancelation of Permit:
☐ Acknowledge that the area have been restored to a safe and orderly condition.
Initiator Signature: Time:
☐ Acknowledge that I have checked the area and been restored to a safe and orderly condition.
Evaluator Signature: Time:
MOBILE PLANT REGISTER Form # HSEQ - MPR Rev 3.docx
Project Information
Project Name:
Date: Location:
Sr. Equipment type / Name Registration No & Exp Date Company Name
Operator Name / Mb. No Operator Third party competency certificate expiry date Operator License expiry date Equipment & Plant 3rd Party Inspection Certificate expiry date SWL / Capacity Signalman /Rigger name & TPC Exp Comment
1
2
3
4
5
6
7
8
9
10.
Remarks:
Inspected By: Signature:
Reviewed By HSE Manager / In charge: Signature:
LABOR ACCOMMODATION CHECKLIST Form # HSEQ - LAC Rev 2.docx
This 5-page document is a checklist for inspecting labour accommodation on a weekly basis. It contains over 100 questions across various categories including access/egress, housekeeping, septic tanks, food preparation, living quarters, firefighting, emergency procedures, first aid, record keeping, environment, and civil defence requirements. Inspectors are to verify that accommodation meets standards for safety, sanitation, emergency preparedness and regulatory compliance by completing the checklist and noting any needed corrective actions or due dates.
INCIDENT INVESTIGATION REPORT Form # HSEQ - IIR Rev 9 -.docx
INCIDENT INVESTIGATION REPORT
(To be submitted to the HSEQ Corporate Office within 7 days of incident.)
1. Project Information:
Project Name: Click here to enter text.
Report No.: Click here to enter text.
Project Location: Click here to enter text.
Property No.: Click here to enter text.
☐ Fatality ☐ Major Incident ☐ Minor Incident
2. Describe the Incident in detail:
Answer who, what, why, where, when & how in this section: (Attach additional pages if required)
Click here to enter text.
☐ Photos Attached
3. Incident Root Causes:
Describe direct, indirect & root cause: (Attach additional pages if required)
Click here to enter text.
4. Key Corrective Actions to Prevent Recurrence:
Describe the corrective actions with timeframe: (Attach additional pages if required)
Click here to enter text.
5. Key Corrections Taken Immediately after the Incident:
Attach additional pages if more space is required:
Click here to enter text.
6. Witnesses:
I declare that I witnessed the incident and the information provided above is true, correct and complete.
No. Name Designation Signature Date
1. Click here to enter text.
Click here to enter text.
Click here to enter text.
2. Click here to enter text.
Click here to enter text.
Click here to enter text.
7. Incident Information:
Initial Incident Report No.: Click here to enter text.
Date Reported: Click here to enter text.
Date of Incident: Click here to enter text.
Time of Incident: Click here to enter text.
Type of Incident: ☐ Near Miss
☐ Major Environmental Incident
☐ Serious Dangerous Occurrence
☐ Equipment / Property Damage
☐ Medical Treatment Case (MTC)
☐ Restricted Work Case (RWC)
☐ Lost Workday Case (LWC)
☐ Serious Occupational Illness/Disease
☐ Class 1 Injuries
☐ Permanent Partial Disability (PPD)
☐ Permanent Total Disability (PTD)
☐ Fatality (F)
Recordkeeping: ☐ Reportable ☐ Recordable
Incident Location on Site: Click here to enter text.
Applicable Reports: ☐ Police
☐ Medical
☐ Other (Specify)
Click here to enter text.
Attached: ☐ Yes ☐ No
☐ Yes ☐ No
☐ Yes ☐ No
8. Injured Person’s Personal Details:
In case of an incident with more than one injured person, complete the information for each person using separate forms.
Name: Click here to enter text.
Occupation: Click here to enter text.
Company: Click here to enter text.
MB / Oracle No.: Click here to enter text.
Nationality: Click here to enter text.
Date of Birth: Click here to enter text.
Passport Number: Click here to enter text.
Length of Service: Click here to enter text.
Gender: ☐ Male ☐ Female
Labour Card No.: Click here to enter text.
9. Incident Causes Details: To be supported with factual evidence
Immediate Cause
(Unsafe Acts) ☐ Failure to secure
☐ Failure to warn
☐ Removing / Defeating Safety Devices
☐
HSE INDUCTION Form # HSEQ - HSEI Rev 2 -.doc
HSE INDUCTION
(Workers)
Name: _________________________________ Trade: ____________________________
M.B. No./Company Name : ________________
Date of Joining: __________________________
SL. N SUBJECT ON INDUCTION PREVIOUS SAFETY EXPOSURE FURTHER SAFETY TRAINING NEED ANALYSIS
1. Introduction Safety Requirements
2. Working Safety is of Primary Importance
3. General Safety Rules
4. Basic Safety Requirements
5. House Keeping
6. Health, Hygiene & Welfare Facilities
7. Fire Extinguisher / Fire Fighting
8. Emergency Procedure
9. Safety Violations & Penalty
10. Safety Award
11. Manual Handling
Induction Given By: Name: ___________________________
Designation: ___________________________
HSE WARNING LETTER-DISCIPLINARY NOTICE Form # HSEQ - HSEWL Rev 6.doc
1st Warning 0 Ref. No. ______________
2nd Warning 0
3rd Warning 0
4th Warning 0 Date: ________________
Employee’s Name : ______________________________________ M.B No. : __________
Occupation : _____________________________________________________________________
Location / Project Site: _____________________________________________________________________
You have committed the following HSE violation/s:
………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………….….
The employee is hereby warned that if the violation is repeated further disciplinary action can be
taken as per the company Code of Conduct.
ORIGINATOR APPROVED BY (MANAGER IN CHARGE / ARABTEC HSEQ & ORG. RISK Manager)
Name: _______________________________ Name: _____________________________
Designation: _______________________________ Designation: _____________________________
Signature:
_______________________________ Signature:
_____________________________
Employee Acknowledgement:
I the undersigned have received this Safety warning letter / disciplinary notice and I admit that I have understood the contents.
0 Received on: ………………………….. (Date) Signature: ………………………………..…..
OFFICE PORTA CABIN INSPECTION Form # HSEQ - OPC Rev 2.docx
Project Information
Project Name: Porta Cabin No:
Location: Contact Person:
Company Name: Date :
Sr. Description Yes No N/A Comments
1. Emergency exit signs are available in right locations
2. Fire alarms and fire extinguishers are visible and accessible.
3. Fire doors (e.g. in stairways) are kept closed unless equipped with automatic closing device
4. Fire extinguishers are serviced regularly
5. Corridors and stairways are kept free of obstruction
6. Fire escape/ evacuation plan available and posted
7. First aid box available
8. Floor surfaces are kept dry and free of slip hazards
9. Electrical cords and plugs are in good condition with proper Grounding
10. Kitchen equipment checked
11. Fire blanket available in the pantry
12. Heat detector available in the pantry
13. Toilets floor clean and dry
14. Are staff trained to use Fire Extinguishers
15. Hand wash/ soap solution available in the toilet
16. Civil Defense or Authority approval
17. Others if any:
Remarks:
Inspected By: Signature:
Reviewed By HSE Manager / In charge : Signature:
More from Dwarika Bhushan Sharma (20)
5 - CLOWNS BELONG IN THE CIRCUS & NOT ON THE JOB.pdf
5 - CLOWNS BELONG IN THE CIRCUS & NOT ON THE JOB.pdf
2-THERE'S A SAFE WAY TO DO EVERY JOB, OF YOU DON'T KNOW ASK.pdf
2-THERE'S A SAFE WAY TO DO EVERY JOB, OF YOU DON'T KNOW ASK.pdf
FIRE PREVENTION REQUIREMENTS Form # HSEQ - Rev 2.docx
FIRE PREVENTION REQUIREMENTS Form # HSEQ - Rev 2.docx
SUB CONTRACTORS HSE CHECKLIST Form # HSEQ - SPSC Rev 2 -.docx
SUB CONTRACTORS HSE CHECKLIST Form # HSEQ - SPSC Rev 2 -.docx
PROJECT LEADER INCIDENT BRIEFING Form # HSEQ - PLIB Rev 2 -.docx
PROJECT LEADER INCIDENT BRIEFING Form # HSEQ - PLIB Rev 2 -.docx
LIFT SHAFT ENTRY PERMIT Form # HSEQ - LSEP Rev 2 -.docx
LIFT SHAFT ENTRY PERMIT Form # HSEQ - LSEP Rev 2 -.docx
LIVE ELECTRICAL WORK PERMIT Form # HSEQ - LEP Rev 2.docx
LIVE ELECTRICAL WORK PERMIT Form # HSEQ - LEP Rev 2.docx
MOBILE PLANT REGISTER Form # HSEQ - MPR Rev 3.docx
MOBILE PLANT REGISTER Form # HSEQ - MPR Rev 3.docx
LABOR ACCOMMODATION CHECKLIST Form # HSEQ - LAC Rev 2.docx
LABOR ACCOMMODATION CHECKLIST Form # HSEQ - LAC Rev 2.docx
INCIDENT INVESTIGATION REPORT Form # HSEQ - IIR Rev 9 -.docx
INCIDENT INVESTIGATION REPORT Form # HSEQ - IIR Rev 9 -.docx
HSE WARNING LETTER-DISCIPLINARY NOTICE Form # HSEQ - HSEWL Rev 6.doc
HSE WARNING LETTER-DISCIPLINARY NOTICE Form # HSEQ - HSEWL Rev 6.doc
OFFICE PORTA CABIN INSPECTION Form # HSEQ - OPC Rev 2.docx
OFFICE PORTA CABIN INSPECTION Form # HSEQ - OPC Rev 2.docx
Recently uploaded
一比一原版(mizzou毕业证书)美国密苏里大学毕业证如何办理
原版一模一样【微信：741003700 】【(mizzou毕业证书)美国密苏里大学毕业证成绩单】【微信：741003700 】学位证，留信认证（真实可查，永久存档）原件一模一样纸张工艺/offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原。
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
【主营项目】
一.毕业证【q微741003700】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【q/微741003700】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
办理(mizzou毕业证书)美国密苏里大学毕业证【微信：741003700 】外观非常简单，由纸质材料制成，上面印有校徽、校名、毕业生姓名、专业等信息。
办理(mizzou毕业证书)美国密苏里大学毕业证【微信：741003700 】格式相对统一，各专业都有相应的模板。通常包括以下部分：
校徽：象征着学校的荣誉和传承。
校名:学校英文全称
授予学位：本部分将注明获得的具体学位名称。
毕业生姓名：这是最重要的信息之一，标志着该证书是由特定人员获得的。
颁发日期：这是毕业正式生效的时间，也代表着毕业生学业的结束。
其他信息：根据不同的专业和学位，可能会有一些特定的信息或章节。
办理(mizzou毕业证书)美国密苏里大学毕业证【微信：741003700 】价值很高，需要妥善保管。一般来说，应放置在安全、干燥、防潮的地方，避免长时间暴露在阳光下。如需使用，最好使用复印件而不是原件，以免丢失。
综上所述，办理(mizzou毕业证书)美国密苏里大学毕业证【微信：741003700 】是证明身份和学历的高价值文件。外观简单庄重，格式统一，包括重要的个人信息和发布日期。对持有人来说，妥善保管是非常重要的。
Personal Growth Unleashed: Key Strategies from Tim Han’s LMA Course
This presentation delves into the core principles of personality development as taught by Tim Han. Understand the importance of self-awareness, goal setting, and maintaining a positive attitude. Gain valuable tips on improving communication skills and developing emotional intelligence. Tim Han’s practical advice and holistic approach will help you embark on a transformative journey towards becoming your best self.
Assignment 1 (Introductions to Microsoft Power point 2019) kiran.pptx
its for fresers to microsoft joiner
7 Habits of Highly Effective People.pptx
Covey says most people look for quick fixes. They see a big success and want to know how he did it, believing (and hoping) they can do the same following a quick bullet list.
But real change, the author says, comes not from the outside in, but from the inside out. And the most fundamental way of changing yourself is through a paradigm shift.
That paradigm shift is a new way of looking at the world. The 7 Habits of Highly Effective People presents an approach to effectiveness based on character and principles.
The first three habits indeed deal with yourself because it all starts with you. The first three habits move you from dependence from the world to the independence of making your own world.
Habits 4, 5 and 6 are about people and relationships. The will move you from independence to interdependence. Such, cooperating to achieve more than you could have by yourself.
The last habit, habit number 7, focuses on continuous growth and improvement.
Aggression - Applied Social Psychology - Psychology SuperNotes
A proprietary approach developed by bringing together the best of learning theories from Psychology, design principles from the world of visualization, and pedagogical methods from over a decade of training experience, that enables you to: Learn better, faster!
ProSocial Behaviour - Applied Social Psychology - Psychology SuperNotes
A proprietary approach developed by bringing together the best of learning theories from Psychology, design principles from the world of visualization, and pedagogical methods from over a decade of training experience, that enables you to: Learn better, faster!
Understanding of Self - Applied Social Psychology - Psychology SuperNotes
A proprietary approach developed by bringing together the best of learning theories from Psychology, design principles from the world of visualization, and pedagogical methods from over a decade of training experience, that enables you to: Learn better, faster!
Stealth attraction for mens gets her with your words
My article gives a set of techniques used by men to subtly and effectively attract women without overtly displaying their intentions. It involves using non-verbal cues, body language, and subtle psychological tactics to create intrigue and build attraction. The goal is to appear confident, mysterious, and charismatic while maintaining an air of mystery that piques the interest of the person you are trying to attract. This approach emphasizes subtlety and finesse in communication and interaction to create a powerful and lasting impression.
Recently uploaded (9)
Personal Growth Unleashed: Key Strategies from Tim Han’s LMA Course
Personal Growth Unleashed: Key Strategies from Tim Han’s LMA Course
Assignment 1 (Introductions to Microsoft Power point 2019) kiran.pptx
Assignment 1 (Introductions to Microsoft Power point 2019) kiran.pptx
Aggression - Applied Social Psychology - Psychology SuperNotes
Aggression - Applied Social Psychology - Psychology SuperNotes
ProSocial Behaviour - Applied Social Psychology - Psychology SuperNotes
ProSocial Behaviour - Applied Social Psychology - Psychology SuperNotes
1-CIE-IGCSE-Additional-Mathematics-Topical-Past-Paper-Functions.pdf
1-CIE-IGCSE-Additional-Mathematics-Topical-Past-Paper-Functions.pdf
Understanding of Self - Applied Social Psychology - Psychology SuperNotes
Understanding of Self - Applied Social Psychology - Psychology SuperNotes
Stealth attraction for mens gets her with your words
Stealth attraction for mens gets her with your words
Rev 00. 10 ways for working safety @ heights poster 30 july-2018
- 1. 10 Ways For Working Safely @ Heights 1 2 3 4 5 6 7 8 9 10 Install full edge protection Barricade off danger area below Be trained to work at heights Don’t enter unsafe platforms Check “scaff–tag” are green Hooks on safety harness Use podium platforms & not step ladder Use both hands don’t’ carry any thing up-down ladders Don’t work alone Harness your tools Engineer, Supervisor & HSE must always “Look Up” at every opportunity