This document describes a collision avoidance system using ultrasonic sensors and a microcontroller. The system works by transmitting ultrasonic pulses and measuring the time it takes for the echo to return, allowing it to calculate the distance to any obstacles. If an obstacle gets too close, the system can activate emergency braking. It also monitors vehicle speed and alerts the driver if the speed limit is exceeded. The system aims to help avoid accidents by detecting obstacles and enforcing speed limits.
The batteries used in electric and hybrid vehicles
consists of several cells with voltages between 3.6V battery and
4.2 V in series or parallel combinations of configurations for
obtaining the necessary available voltages in the operation of a
hybrid electric vehicle. How malfunction of a single cell affects
the behavior of the entire battery pack, BMS main function is to
protect individual cells against over-discharge, overload or
overheating. This is done by correct balancing of the cells. In
addition BMS estimates the battery charge status
The established PTC-1 offers a robust and reliable solution to the growing demands of modern junctions and pedestrian facilities. The original PTC-1 offers efficient control for larger junctions, whilst the smaller PTC-1 Lite has been developed to run small junctions and pedestrian crossings. Capable of working in conjunction with old technology 240v aspects and the new 48v LED energy efficient aspects, the PTC-1 family of controllers is truly adaptable and able to deliver in any given situation.
Speed Control of Induction Motor Using PLC and SCADA SystemIJERA Editor
Automation or automatic control is the use of various control systems for operating equipment such as
machinery, processes in factories, boilers and heat-treating ovens, switching in telephone networks, steering and
stabilization of ships, aircraft and other applications with minimal or reduced human intervention. Some
processes have been completely automated. The motor speed is controlled via the driver as an open loop control.
To make a more precise closed loop control of motor speed we will use a tachometer to measure the speed and
feed it back to the PLC, which compares to the desired value and take a control action, then the signal is
transferred to the motor – via driver – to increase / decrease the speed. We will measure the speed of the motor
using an incremental rotary encoder by adjusting parameters (PLC, driver) and also we need to reduce the
overall cost of the system. Our control system will be held using the available Siemens PLC. In addition, we will
monitor motor parameters via SCADA system.
The batteries used in electric and hybrid vehicles
consists of several cells with voltages between 3.6V battery and
4.2 V in series or parallel combinations of configurations for
obtaining the necessary available voltages in the operation of a
hybrid electric vehicle. How malfunction of a single cell affects
the behavior of the entire battery pack, BMS main function is to
protect individual cells against over-discharge, overload or
overheating. This is done by correct balancing of the cells. In
addition BMS estimates the battery charge status
The established PTC-1 offers a robust and reliable solution to the growing demands of modern junctions and pedestrian facilities. The original PTC-1 offers efficient control for larger junctions, whilst the smaller PTC-1 Lite has been developed to run small junctions and pedestrian crossings. Capable of working in conjunction with old technology 240v aspects and the new 48v LED energy efficient aspects, the PTC-1 family of controllers is truly adaptable and able to deliver in any given situation.
Speed Control of Induction Motor Using PLC and SCADA SystemIJERA Editor
Automation or automatic control is the use of various control systems for operating equipment such as
machinery, processes in factories, boilers and heat-treating ovens, switching in telephone networks, steering and
stabilization of ships, aircraft and other applications with minimal or reduced human intervention. Some
processes have been completely automated. The motor speed is controlled via the driver as an open loop control.
To make a more precise closed loop control of motor speed we will use a tachometer to measure the speed and
feed it back to the PLC, which compares to the desired value and take a control action, then the signal is
transferred to the motor – via driver – to increase / decrease the speed. We will measure the speed of the motor
using an incremental rotary encoder by adjusting parameters (PLC, driver) and also we need to reduce the
overall cost of the system. Our control system will be held using the available Siemens PLC. In addition, we will
monitor motor parameters via SCADA system.
Speed checker on highway using 8051 micro controller and IR sensors. Here IR sensor sense the speed of the vehicle and and controller display the speed on Liquid Crystal Display,
with the help of intelligent braking system we can reduce the chances of accident and save human life. this system is based on STM32F3 micro-controller board,LPC-1768 board and Ultra-sonic sensor etc.
Designs of input and output driver circuits for 16 bit electronic control uni...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Synopsis for alcohol detection with vehicle controlling (1)Pankaj Singh
The main purpose behind this project is “Drunk driving detection”. Now a days, many accidents are happening because of the alcohol consumption of the driver or the person who is driving the vehicle. Thus Drunk driving is a major reason of accidents in almost all contries all over the world. Alcohol Detector in Car project is designed for the safety of the people seating inside the car. This project should be fitted / installed inside the vehicle.
Analysis of Induction Motor Speed Control Using SCADA Based Drive Operated Sy...IJSRD
This Paper represents the analysis of induction motor speed control using VFD (Variable Frequency Drive) system operated by PLC-SCADA system. The main aim of the paper is to dealt with the concept of speed control of a three-phase induction motor with energy saving. To do so, a VFD (Variable Frequency Drive) is used for controlling the speed of a three-phase induction motor with variable load attached to the motor. It certainly leads to the best performance and high efficiency of the induction motor. Programmable Logic Controller (PLC) and Supervisory Control And Data Acquisition (SCADA) are two new systems to control a Variable Frequency Drive (VFD) whose output is given to a three-phase induction motor and driving a conveyor belt. The conveyor belt has three sensors are inputs which senses a passing object and carries out the necessary instructions programmed in ladder logic programming of the PLC through the computer (PC). The SCADA software installed in the PC in turn enables the human operator to control the entire operation away from the plant and just by using the virtual inputs designated on his computer screen.
Design and development of programmable controller for air sampling machineeSAT Journals
Abstract A programmable Controller is designed and developed for time pedestal controlling of Air Sampling Machine. The major purpose of the designed system is to reduce filter damage of Air Sampling Machine. The main function of the controller is to automatically switching the Air Sampling Machine with predefined On-Off time interval for 24 hours operation. This is a low cost system which is designed using locally available components and user friendly. The controlling operation is maintained by ATMEL AT89C52 microcontroller. A programmable real time clock PCF8583 is used to produce timing control signal for automatic switching of the Air Sampling Machine. Control signals generated by real time clock operate opto-isolator and an electromechanical relay for switching the Air Sampling Machine. EEPROM (M24C64) is used to store necessary data. The instruction firmware for the designed controller has been developed in BASIC platform using BASCOM-8051 software. The designed system is functioning properly and serving the purpose of the design. Keywords: Programmable Controller, AT89C52 microcontroller, RTC, EEPROM, I2C Protocol, BASCOM-8051 IDE
TRAFFIC SIGNAL CONTROL USING IR SENSORSKunal Kabra
The main objective of this project is to design an intelligent auto traffic signal control system.
Traffic congestion is one of the major issues to be considered. Generally Vehicular traffic
Intersects at the junctions of the road and are controlled by the traffic signals .Traffic signals
Need a good coordination and control to ensure the smooth and safe flow of the vehicular traffic.
During the rush hours, the traffic on the roads is at its peak. Also, there is a possibility for the
Emergency vehicles to stuck in the traffic jam. Therefore; there is a need for the dynamic control
of the traffic during rush hours. Hence I propose a smart traffic signal controller .The proposed
System tries to minimize the possibilities of traffic jams, caused by the traffic lights, to some
Extent by clearing the road with higher density of vehicles and also provides the clearance for the Emergency vehicle if any. The system is based on the AVR micro controller and IR sensors
Technology.
Design and Construction of DC Motor Speed Controller Using Android.pptEEESrproject
Rapid progress in microelectronics and microcontrollers in recent years has made it possible to apply modern control technology to control efficient and reliable operation of many applications such as the engine, anti-lock braking system (ABS), cruise, steering, and vehicle traction. Many of these operations including DC motor and therefore there is a need for implementing effective control strategies with digital control of these motors. The speed of DC motor is directly proportional to armature voltage and inversely proportional to field flux and adjustable speed drives can be operated over a wide range by controlling armature or field excitation. Development of various solid state switching devices such as diode, transistor and thyristor along with various analog/digital chips used in firing/controlling circuits, have made dc drives more handy for control in numerous areas of applications. For DC motor speed control, closed-loop PWM technique is widely used and well known . In this technique, the regulation of motor’s speed is realized by changing the voltage of motor which is adjusted by the duty ratio of PWM. In order to improve the performance of motor’s speed regulation and to reduce the steady-state error of the rotational speed of motor, a high- performance microcontroller can be used.In this work, an arduino microcontroller is used for implementation.
Speed checker on highway using 8051 micro controller and IR sensors. Here IR sensor sense the speed of the vehicle and and controller display the speed on Liquid Crystal Display,
with the help of intelligent braking system we can reduce the chances of accident and save human life. this system is based on STM32F3 micro-controller board,LPC-1768 board and Ultra-sonic sensor etc.
Designs of input and output driver circuits for 16 bit electronic control uni...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Synopsis for alcohol detection with vehicle controlling (1)Pankaj Singh
The main purpose behind this project is “Drunk driving detection”. Now a days, many accidents are happening because of the alcohol consumption of the driver or the person who is driving the vehicle. Thus Drunk driving is a major reason of accidents in almost all contries all over the world. Alcohol Detector in Car project is designed for the safety of the people seating inside the car. This project should be fitted / installed inside the vehicle.
Analysis of Induction Motor Speed Control Using SCADA Based Drive Operated Sy...IJSRD
This Paper represents the analysis of induction motor speed control using VFD (Variable Frequency Drive) system operated by PLC-SCADA system. The main aim of the paper is to dealt with the concept of speed control of a three-phase induction motor with energy saving. To do so, a VFD (Variable Frequency Drive) is used for controlling the speed of a three-phase induction motor with variable load attached to the motor. It certainly leads to the best performance and high efficiency of the induction motor. Programmable Logic Controller (PLC) and Supervisory Control And Data Acquisition (SCADA) are two new systems to control a Variable Frequency Drive (VFD) whose output is given to a three-phase induction motor and driving a conveyor belt. The conveyor belt has three sensors are inputs which senses a passing object and carries out the necessary instructions programmed in ladder logic programming of the PLC through the computer (PC). The SCADA software installed in the PC in turn enables the human operator to control the entire operation away from the plant and just by using the virtual inputs designated on his computer screen.
Design and development of programmable controller for air sampling machineeSAT Journals
Abstract A programmable Controller is designed and developed for time pedestal controlling of Air Sampling Machine. The major purpose of the designed system is to reduce filter damage of Air Sampling Machine. The main function of the controller is to automatically switching the Air Sampling Machine with predefined On-Off time interval for 24 hours operation. This is a low cost system which is designed using locally available components and user friendly. The controlling operation is maintained by ATMEL AT89C52 microcontroller. A programmable real time clock PCF8583 is used to produce timing control signal for automatic switching of the Air Sampling Machine. Control signals generated by real time clock operate opto-isolator and an electromechanical relay for switching the Air Sampling Machine. EEPROM (M24C64) is used to store necessary data. The instruction firmware for the designed controller has been developed in BASIC platform using BASCOM-8051 software. The designed system is functioning properly and serving the purpose of the design. Keywords: Programmable Controller, AT89C52 microcontroller, RTC, EEPROM, I2C Protocol, BASCOM-8051 IDE
TRAFFIC SIGNAL CONTROL USING IR SENSORSKunal Kabra
The main objective of this project is to design an intelligent auto traffic signal control system.
Traffic congestion is one of the major issues to be considered. Generally Vehicular traffic
Intersects at the junctions of the road and are controlled by the traffic signals .Traffic signals
Need a good coordination and control to ensure the smooth and safe flow of the vehicular traffic.
During the rush hours, the traffic on the roads is at its peak. Also, there is a possibility for the
Emergency vehicles to stuck in the traffic jam. Therefore; there is a need for the dynamic control
of the traffic during rush hours. Hence I propose a smart traffic signal controller .The proposed
System tries to minimize the possibilities of traffic jams, caused by the traffic lights, to some
Extent by clearing the road with higher density of vehicles and also provides the clearance for the Emergency vehicle if any. The system is based on the AVR micro controller and IR sensors
Technology.
Design and Construction of DC Motor Speed Controller Using Android.pptEEESrproject
Rapid progress in microelectronics and microcontrollers in recent years has made it possible to apply modern control technology to control efficient and reliable operation of many applications such as the engine, anti-lock braking system (ABS), cruise, steering, and vehicle traction. Many of these operations including DC motor and therefore there is a need for implementing effective control strategies with digital control of these motors. The speed of DC motor is directly proportional to armature voltage and inversely proportional to field flux and adjustable speed drives can be operated over a wide range by controlling armature or field excitation. Development of various solid state switching devices such as diode, transistor and thyristor along with various analog/digital chips used in firing/controlling circuits, have made dc drives more handy for control in numerous areas of applications. For DC motor speed control, closed-loop PWM technique is widely used and well known . In this technique, the regulation of motor’s speed is realized by changing the voltage of motor which is adjusted by the duty ratio of PWM. In order to improve the performance of motor’s speed regulation and to reduce the steady-state error of the rotational speed of motor, a high- performance microcontroller can be used.In this work, an arduino microcontroller is used for implementation.
The Design of Multi-Platforms Rail Intelligence Flatness Detection SystemIJRESJOURNAL
ABSTRACT: In this paper,we design a Multi-platforms intelligent system for flatness detection of rail welding headbased on thedevelopment environment of Android software .The system uses a STM32 chip as control core, a handheld smart terminal or personal computer as the carrier. The datas transmitted to intelligent terminal or computer through the bluetooth communication technology are processed rapidly, the data curve is drawed and the flatness characteristic parameters of the measured rail welding head is identified. The system provides a friendly intuitive monitoring and operation interface, has the characteristics of fast, reliable, energy saving, high accuracy, etc.
In this project we are going to make an embedded system which will help to provide protection against theft. This system will send the data to the user who want to track the vehicle showing the using position of vehicle in terms of latitude and longitude. Most of the people know that GPS is more secure but they don’t apply because it is expensive. This design is needed for the real time location of the vehicle. It changes the microcontroller P89V51RD2 interfaces with various hardware peripheries this uncontrolled interfaces serially with GSM modem and GPS receiver.
The peer-reviewed International Journal of Engineering Inventions (IJEI) is started with a mission to encourage contribution to research in Science and Technology. Encourage and motivate researchers in challenging areas of Sciences and Technology.
International Journal of Engineering Research and Development (IJERD)IJERD Editor
journal publishing, how to publish research paper, Call For research paper, international journal, publishing a paper, IJERD, journal of science and technology, how to get a research paper published, publishing a paper, publishing of journal, publishing of research paper, reserach and review articles, IJERD Journal, How to publish your research paper, publish research paper, open access engineering journal, Engineering journal, Mathemetics journal, Physics journal, Chemistry journal, Computer Engineering, Computer Science journal, how to submit your paper, peer reviw journal, indexed journal, reserach and review articles, engineering journal, www.ijerd.com, research journals,
yahoo journals, bing journals, International Journal of Engineering Research and Development, google journals, hard copy of journal
1. 1
ACCIDENT AVOIDANCE WITH DYNAMIC SPEED GOVERNOR
Abstract:
Automotive vehicles are increasingly being
equipped with collision avoidance and
warning systems for predicting the potential
collision with an external object, such as
another vehicle or a pedestrian. Upon
detecting a potential collision, such systems
typically initiate an action to avoid the
collision and/or provide a warning to the
vehicle operator. This system consist of a
distance-measuring system based on
ultrasonic sound utilizing the PIC 16f877A
microcontroller and transmits a burst of
ultrasonic sound waves towards the target
and then receives the corresponding echo.
An ultrasonic sound sensor is used to detect
the arrival of the echo to the system. The
time taken for the ultrasonic burst to travel
the distance from the system to the subject
and back to the system is accurately
measured by the microcontroller. It also
provides a warning signal to the driver if the
distance between vehicle and obstacle
crosses a particular limit. It also monitors
the speed of the vehicle and if the speed limit
is exceeded it is informed to the driver. The
speed limit for different class of vehicles is
set by authorities at different.
.
Introduction:
This report describes a distance-measuring
system based on ultrasonic sound utilizing
the PIC 16f877A microcontroller. With the
help of the distance measured, the micro-
controller will make the vehicle stop
suddenly if the vehicle is about to hit any
obstacle or any other vehicle. With the help
of this technology accidents are avoided.
The system transmits a burst of ultrasonic
sound waves towards the target and then
receives the corresponding echo. An
ultrasonic sound sensor is used to detect the
arrival of the echo to the system. The time
taken for the ultrasonic burst to travel the
distance from the system to the subject and
back to the system is accurately measured
by the microcontroller. Different types of
vehicle speed limiters are in current use for
regulating traffic especially across roads
near populated areas such as hospitals, malls
and schools. This project “DYNAMIC
SPEED GOVERNER” is a new method by
which vehicle speed is controlled externally
rather than internally .The speed
measurement and control is accomplished
via two PIC16F877As with a RF transmitter
and receiver.
2. 2
Software Description:
The MPLAB software is from Microchip
and it is an Integrated Development
Environment (IDE). It is basically used for
programming the ICs. In this project the
coding is done in Embedded C language for
that C compiler is required so HITECH C
compiler is used. The PID algorithm first
written in embedded C language for that
initially new project is created in MPLAB
IDE. After that PID code is build and
compiled in MPLAB IDE from that the
generated .cof file is used for debugging
purpose and the .hex file is used to
download it in PIC16F877A IC. It was
largely used for real time debugging of PID
code. The PIC16F877A is programmed
through MPLAB IDE and PICKET3. The
PROTEUS is the virtual simulation software
from ISIS. PROTEUS is generally used to
test the behavior of the selected hardware in
simulation. In PROTEUS the PID code was
initially tested with different logics on
virtual hardware. The magnetic pick up
sensor driver circuit checked in PROTEUS
by observing its output waveform on
oscilloscope. The various inputs given to the
magnetic pickup sensor driver circuit from
function generator were observed on
controller. The actuator driver circuit is also
tested with different Volts and Ampere
ratings in PROTEUS. The PCB123 is the
PCB design software from Sunstone
Circuits. The actuator and magnetic pickup
sensor driver circuit were designed in
PCB123. First the schematics were drawn
and from that the layout work is created.
The both designs were in program through
hole format so the components chosen were
in same format. All the driver circuit’s
components were found in same
specifications in PCB123. The controller
board also designed in PCB123 with same
program through hole format.
Literature review:
The new speed limiting system presented in
this project combines several pioneering
techniques that integrate wireless
technologies in order to implement a reliable
speed control system. This proposed system
can be easily implemented near different
populated areas. The power of the proposed
system lies in its flexibility and capability of
development with little hardware changes
such as changing the speed limits and speed
control methods using the software of the
base station in negligible amount of time.
The proposed system is based on
microcontroller technology for collecting
data related to speed and transmitting it
through a transceiver to a base station that
3. 3
analyzes the transmitted data and takes
appropriate decisions related to speed limit
and control requirements. Speed Governor
regulates the top speed and/or maximum
rpm of a vehicle, whether it is electronically
or mechanical. The governor is emplaced by
the manufacturer to meet laws of the nation
is which the vehicle will be sold, protect the
drivers from operating at unsafe speed, or to
protect the car from being driving beyond its
physical or mechanical threshold.
Speed governor:
The following Figure 1 shows block
diagram of working of electronic speed
governor system. The magnetic pickup
sensor is mounted on engine flywheel. The
engine rpm is measured in capture compare
module of the PIC microcontroller. The
throttle actuator’s lever is directly connected
to the engine fuel pump. The throttle
actuator is controlled from the pulse width
modulation signal so it is directly connected
to the RC2 pin of the PIC microcontroller.
The engine rpm is continuously measured
and compared with the required set point
and when the error signal is generated it is
directly processed in the PID algorithm. The
PIC microcontroller generates the required
pulse width modulation duty cycle from the
PID algorithm based on which diesel engine
gets stabilized at required set point. The
working pulse width modulation period is
calculated from initial trails on the throttle
actuator.
Figure 1: Block diagram of Electronic
Speed Governor System
In this CCP1 (PWM) is used to control the
position of throttle actuator. PWM stands for
the Pulse Width Modulation where the width
of a digital waveform is varied to control the
power delivered to a load. The underlying
principle in the whole process is that the
average power delivered is directly
proportional to the modulation duty cycle as
shown in Figure 2. The pulse width
modulation is required to switching the load
devices through MOSFET based power
stage or from any other components. The
pulse width modulation has ON time and
OFF time and addition of both is period. The
average voltage applied to the load is varied
from the pulse width modulation which
4. 4
directly depends upon the duty cycle. The
time is inversely proportional to the
frequency because of which the required
period given to the load is in the form of
frequency.
Figure 2: Pulse width modulation with
different duty cycle.
Design of Controller:
The improved electronic speed governor
system includes digital controller, drive
circuit, electromagnetic throttle actuator and
the engine speed sensor. The system to be
controlled (plant) is the diesel engine. The
electronic speed governor is a closed loop
system in which feedback is taken from
engine rpm. The controller output is in the
form of pulse width modulation duty cycle.
When the rpm error is generated the
required pulse width modulation duty cycle
is calculated from PID algorithm. The
capture compare module in PIC16F877A is
used to calculate engine rpm. The PID
update time is kept in proportion with the
throttle actuator response time. The key step
of the electronic governor design is to
choose the suitable actuator coupled suitably
with fuel pump rack. The requirements to
actuator of diesel engine governor system
are fast response, high accuracy and
reliability. Under diesel engine operating
principle, the engine speed regulation is
achieved by regulating the movement of the
pump rack. With electronic speed controller,
the movement of pump rack is mainly
affected by the diesel engine speed change.
Microcontroller PIC 16F877A:
The microcontroller is a set of digital logic
circuits integrated on a single silicon „chip‟
whose connections and behavior can be
specified and later alter when required, by
the program in its memory. 16F877A have
enough I/O lines for current need. It is
capable of initiating all intersystem
communications. The master controller
controls each functions of the system with a
supporting device. Also responsible for
reception of commands from the host and
taking necessary actions . PIC16F877A is an
8-bit, fully static, EPROM/EPROM/ROM-
based CMOS microcontroller. It employs
5. 5
RISC architecture with only 35 word/single
cycle instructions. All these instructions are
single cycle (1ms) expect for program
branches which takes two cycles. The
PIC16f877A products are supported by a
full featured macro assembler, a software
simulator, „C‟ compiler etc.
Features:
Two pins High-performance RISC
CPU.
All single cycle instructions except
for program branches which are 2
cycle.
Operating speed: DC - 20 MHz
clock input DC - 200 ns instruction
cycle.
Up to 8K x 14 words of Flash
Program Memory.
Up to 256 x 8 bytes of EEPROM
data memory.
Pin out compatible to the
PIC16C73/74/76/77.
Interrupt capability -up to 14
internal/external.
Eight level deep hardware stack
Direct, indirect, and relative
addressing modes.
Power-on Reset (POR)
Power-up Timer (PWRT) and
Oscillator Start-up Timer (OST)
Watchdog Timer (WDT) with its
own on-chip RC Oscillator for
reliable operation.
Programmable code-protection.
Power saving SLEEP mode
Selectable oscillator options.
Low-power, high-speed CMOS
EPROM/EEPROM technology.
Fully static design.
Only single 5V source needed for
programming capability.
In-Circuit Debugging via two pins
Processor read/write access to
program memory.
Wide operating voltage range: 2.5V
to 5.5V.
High Sink/Source Current: 25 mA.
Commercial and Industrial
temperature ranges
RF encoder:
HT12E The 2^12 encoders are a series of
CMOS LSIs for remote control system
applications. They are capable of encoding
information which consists of N address bits
and 12_N data bits. Each address/ data input
can be set to one of the two logic states. The
programmed addresses/data are transmitted
together with the header bits via an RF or an
6. 6
infrared transmission medium upon receipt
of a trigger signal. The capability to select a
TE trigger on the HT12E or a DATA trigger
on the HT12A further enhances the
application flexibility of the 2^12 series of
encoders. The HT12A additionally provides
a 38 kHz carrier for infrared systems.
RF transmitter:
The RF Transmitter is ideal for remote
control applications where low cost and
longer range is required. The transmitter
operates from a 1.5 to 12v supply, making it
ideal for battery-powered applications. The
transmitter employs a SAW stabilized
oscillator, ensuring accurate frequency
control for best range performance. Output
power and harmonic emissions are easy to
control. The manufacturing friendly SMT
style package and low cost make the RF
module make it suitable for high volume
applications.
RF receiver:
The RF Receiver we are using is ideal for
short-range remote control applications
where cost is a primary concern. The
receiver module requires no external RF
components except for the antenna. It
generates virtually no emissions. The super
regenerative design exhibits exceptional
sensitivity at a very low cost. A SAW filter
can be added to the antenna input to improve
selectivity for applications that require
robust performance. The friendly SIP style
package and low-cost make it suitable for
high volume applications
RF decoder:
HT12D The 2^12 decoders are a series of
CMOS LSIs for remote control system
applications. They are paired with Holtek_s
212 series of encoders (refer to the
encoder/decoder cross reference table). For
proper operation, a pair of encoder/decoder
with the same number of addresses and data
format should be chosen. The decoders
receive serial addresses and data from a
programmed 212 series of encoders that are
transmitted by a carrier using an RF or an IR
transmission medium. They compare the
serial input data three times continuously
with their local addresses. If no error or
unmatched codes are found, the input data
codes are decoded and then transferred to
the output pins. The VT pin also goes high
to indicate a valid transmission. The 2^12
series of decoders are capable of decoding
information that consist of N bits of address
and 12_N bits of data. Of this series, the
HT12D is arranged to provide 8 address bits
and 4 data bits, and HT12F is used to decode
7. 7
12 bits of address information .The below
figure shows the RF system.
Ultrasonic sensors:
Fig . Ultrasonic sensor
Ultrasonic sensors are commonly used for a
wide variety of noncontact presence,
proximity, or distance measuring
applications. These devices typically
transmit ultrasonic sound toward a target,
which reflects the sound back to the sensor.
The system then measures the time for the
echo to return to the sensor and computes
the distance to the target using the speed of
sound in the medium .The wide varieties of
sensors currently on the market differ from
one another in their mounting
configurations, environmental sealing, and
electronic features. Acoustically, they
operate at different frequencies and have
different radiation patterns. It is usually not
difficult to select a sensor that best meets the
environmental and mechanical requirements
for a particular application, or to evaluate
the electronic features available with
different models. The principle of working
of an ultrasonic sensor is easy. The sensor
transmits ultrasonic sound waves and waits
for reflected sound waves. After receiving
reflected sound wave or usually named
echo, sensor detects the distance in different
ways. Triggered the sensor and then wait for
echo pulse. Measuring echo pulse width is
important for us because 30 μs means us 1
cm.
Ultrasonic ranging system:
The development of applications using
ultrasonic sensors requires good
understanding of its operating principles and
Fig.RF section
8. 8
its interaction with the environment. They
rely on the principle of time of flight or
propagation of sound waves in air. The
system either measures the echo reflection
of the sound from the object (in case where
the transmitter and the receiver is on the
same device) or the time of flight of the
sound wave from the transmitter to the
receiver (in case either the transmitter or the
receiver is mounted on the object).
Basically, the range finding sensors can be
classified into two categories:
I. Time of flight sensors.
II. Phase-shift detection sensors.
The first method is the most common
technique employed, and it consists in
measuring the time of flight of a pulse of
emitted energy (light or acoustic) travelling
to a reflecting object, than echoing back to a
receiver. The formula used to compute the
distance d is straight forward:
2d = v* t
Where v is the signal speed of propagation
(300 m/sec for sound) and t is the time
elapsed between emission and reception.
The method uses commonly ultrasonic
acoustic pulses. The use of light pulses
places severe requirements on associated
control and measurement circuitry: for
example to obtain 1mm resolutions the
timing accuracy must be around 3
picoseconds, a capability expensive and
difficult to realize.
Ultrasonic transmitter:
The transmitter consists of an electronics
circuitry and an electromechanical
transducer. The electronic circuitry
generates the required frequency electrical
signal and the electromechanical transducer
converts that electrical signal into the
physical form and activates the open
medium surface. This oscillating physical
surface creates the ultrasonic waves. The
oscillating surface creates a pressure
variation and ultimately a pressure wave
with a frequency equal to that of the surface
oscillation.
Ultrasonic receiver:
The receiver also has the same configuration
except that it has a receiver electronic
circuitry and a transducer, which converts
the ultrasonic sound waves into an electrical
9. 9
signal. The sound waves travel into the
medium and are reflected by an object in the
path of the waves. This reflected wave is
then sensed by the receiver, which actually
calculates the time of flight of the signal to
find the distance.
Transmitter and receiver pair:
It consists of a transmitter and receiver pair
on the device. There are two different
transducers for transmitter and receiver. The
transmitter transmits and the receiver waits
for the reflected signals.
LCD display:
The LCD module is a parallel interface
sixteen pin module. The first three pins of
LCD module are used for contrast adjusting.
Here the first pin is connected to ground,
second to the voltage supply and third to the
variable resistor. The pins, seven to fourteen
are data lines (D0 to D7). In this particular
circuit the data lines D4 to D7 are used
because the LCD driver available is 4 line
data bus. 15th pin is connected to the 5 volt
supply. Pin 4, 5, 6 are control pins, R/W, RS
and enable respectively. 16th pin is
connected to the ground through a transistor.
The voltage from pic16f877a turn on the
transistor and it in turn turns on the LCD
backlight. LCD display used to display the
speed of vehicles from speed Governor and
distance measured by Ultrasonic ranging
system.
Working:
Fig. working of accident avoidance system
The above figure shows working of accident
avoidance system .The dynamic speed
governor consist of mainly two parts the
transmitter and receiver. The system is
mainly based on micro controller technology
for collecting data related to speed and
transmits the data to the micro controller
10. 10
using RF communication. The micro
controller analyses the transmitted data and
takes appropriate decisions related to speed
limit and control requirements. The dynamic
speed governor will be needed in populated
areas such as hospitals, malls and schools
for regulating traffic. The RF transmitter of
the system is mounted on the signal board
and the micro controller of the transmitter
part always sense the speed limit of the area
for that the speed limit will be stored in the
micro controller. The speed limit of the
vehicle will be transmitted using RF
transmitter to the approaching vehicles .An
RF receiver is kept inside the vehicle and the
receiver accepts the incoming signals and
then feeds the limit of speed as an input to a
comparator. An RPM meter is used to
transform the mechanical rotational
movement of the vehicle into an electrical
signal and using this method the speed of the
approaching vehicle can be detected. This
calculated speed from the RPM meter is
given to the next input pin of the
comparator. At the comparator both speed
given to the both input pin is compared and
if the speed of the vehicle is greater than the
speed limit the controller will reduce the
speed of the vehicle to the limit by using
PWM characteristic of the micro controller.
Advantages:
Increased road safety.
Reduced strain on engines, thereby
increasing the life of engines.
Reduce fuel consumption.
Reduced pollution & thus improved
environment.
Reduced maintenance cost for the vehicle
owner(s).
Conclusion:
. The speed limiting system presented in this
project combines several pioneering
techniques that integrate wireless
technologies in order to implement a reliable
speed control system. This can be easily
implemented near different populated areas.
The power of the proposed system lies in its
flexibility and capability of development
with little hardware changes such as
changing the speed limits and speed control
methods using the software of the base
station in negligible amount of time. The
proposed system is based on microcontroller
technology for collecting data related to
speed and transmitting it through a
transceiver to a base station that analyzes the
transmitted data and takes appropriate
decisions related to speed limit and control
requirements. This experience has
encouraged us to learn more about
upcoming trends and technologies and
11. 11
thereby adding our bumble knowledge and
experience about the vast ocean of
electronics
References:
[1] Zutao Zhang, Jiashu Zhang, “A Novel
Vehicle Safety Model: Vehicle speed
Controller under Driver Fatigue”, “IJCSNS
International Journal of Computer Science
and Network Security”, VOL.9 No.1,
January 2009
[2] M. Bertozzi,A.Brogg M. Cellario, A.
Fascioli, P.Lombardi, and M.Porta,
“Artifical vision in road vehicles,”
Proceedings of the IEEE, vol.
90,no. 7, pp. 1258–1271, 2002.
[3] S. Tsugawa and Sadayuki, “Vision-based
vehicle on japan: Machine vision systems
and driving control systems,” IEEE Trans.
on Ind. El.???, vol.
41, no. 4, pp. 398–405, 1994.
[4] Vehicle-highway automation activities in
the United States. U.S. Dept of
Transportation, 1997