Critical Current Control (C3) and Modeling of a Buck Based LED Driver with Power Factor Correction
•
0 likes•15 views
Buck converter has a good aptitude for LED driver application. Here a new technique introduced to control and model a buck converter in the closed loop condition using Lagrange equation. To improve the final model accuracy, parasitic elements of the converter are taken into account. The main advantage of this method is its novelty and simple implementation. Also, the converter power factor has improved under critical current control (C3) technique. Frequency response and step response of the small signal model are derived and analysed. The theoretical predictions are tested and validated by means of PSIM software. Finally, precise agreement between the proposed model and the simulation results has obtained.
Report
Share
Report
Share
Download to read offline
Recommended
Design and Control of Wind integrated Shunt Active Power Filter to Improve Po...
In this paper wind energy conservation system (WECS) with shunt active power filter (SAPF) is proposed for harmonics elimination, power factor correction, reactive power compensation and grid current balancing. Adaptive neuro fuzzy inference system (ANFIS) based controller is implemented at WECS side to control the boost converter to achieve MPP and at SAPF sides to minimize voltage variations and enhance power quality. Here, synchronous reference frame (SRF) theory based reference current generation technique is employed in SAPF. The proposed scheme is implemented in MATLAB/Simulink. The results confirm that this method has better performance and can maintain total harmonic distortion (THD) level of the system within the IEEE standard 519.
Power quality improvement in utility interactive based ac dc converter using ...
This paper highlights the power quality issues and explains the remedial measures taken by means of hybrid front-end third harmonic current injection rectifiers. Here zig-zag transformer is used as the current injection device so that the advantages pertaining to the zig-zag transformer is effectively utilized. The third harmonic current injection device along with three-level boost converter at the output stage will increase the DC-link voltage. With less boost inductance, generally half of the conventional boost converter inductance is sufficient to implement the proposed converter structure resulting in reduced ripple current and also the device rating is reduced by half of the output voltage. Moreover, the power quality is well improved using third harmonic current modulated front-end structure which is well appropriate for medium/higher power applications. The experimental prototype of hybrid front-end converter is developed in the laboratory to validate the MATLAB simulation results.
A three phase grid tied spv system with adaptive dc link voltage for cpi volt...
This paper deals with a three-phase two-stage grid tied SPV (solar photo-voltaic) system. The first stage is a boost converter, which serves the purpose of MPPT (maximum power point tracking) and feeding the extracted solar energy to the DC link of the PV inverter, whereas the second stage is a two-level VSC (voltage source converter) serving as PV inverter which feeds power from a boost converter into the grid. The proposed system uses an adaptive DC link voltage which is made adaptive by adjusting reference DC link voltage according to CPI (common point of interconnection) voltage. The adaptive DC link voltage control helps in the reduction of switching power losses. A feed forward term for solar contribution is used to improve the dynamic response. The system is tested considering realistic grid voltage variations for under voltage and over voltage. The performance improvement is verified experimentally. The proposed system is advantageous not only in cases of frequent and sustained under voltage (as in the cases of far radial ends of Indian grid) but also in case of normal voltages at CPI. The THD (total harmonics distortion) of grid current has been found well under the limit of an IEEE-519 standard.
An f p q droop control in cascaded-type microgrid
In cascaded-type microgrid, the synchronization and power balance of distributed generators become two new issues that needs to be addressed urgently. To that end, an f-P/Q droop control is proposed in this letter, and its stability is analyzed as well. This proposed droop control is capable to achieve power balance under both resistive-inductive an resistive-capacitive loads autonomously. Compared with the inverse power factor droop control, an obvious advantage consists in extending the scope of application. Finally, the feasibility of the proposed method is verified by simulation results.
Designing of Multilevel DPFC to Improve Power Quality
According to growth of electricity demand and the increased number of non-linear loads in power grids, providing a high quality electrical power should be considered. In this paper, Enhancement of power quality by using fuzzy based multilevel power flow controller (DPFC) is proposed. The DPFC is a new FACTS device, which its structure is similar to unified power flow controller (UPFC). In spite of UPFC, in DPFC the common dc-link between the shunt and series converters is eliminated and three-phase series converter is divided to several single-phase series distributed converters through the line. This eventually enables the DPFC to fully control all power system parameters. It, also, increases the reliability of the device and reduces its cost simultaneously. In recent years multi level inverters are used high power and high voltage applications .Multilevel inverter output voltage produce a staircase output waveform, this waveform look like a sinusoidal waveform leads to reduction in Harmonics. Fuzzy Logic is used for optimal designing of controller parameters. Application of Fuzzy Multilevel DPFC for reduction of Total Harmonic Distortion was presented. The simulation results show the improvement of power quality using DPFC with Fuzzy logic controller.
Single-Stage Switched-Capacitor Module (S3CM) Topology for Cascaded Multileve...
A two-stage switched-capacitor based multilevel inverter possesses a drawback such that switches in the second stage (i.e. H-bridge) endure higher voltage stress. To resolve this problem, this letter proposes a single-stage switched-capacitor module (S3CM) topology for cascaded multilevel inverter which ensures the peak inverse voltage across all switches within the dc source voltage. Nine voltage levels can be generated with only one dc source and two incorporated capacitors. Hence, the number of isolated dc sources are significantly reduced compared to cascaded H-bridge. In addition, voltage boosting gain of two is achieved. A comparative analysis against the recent topology reveals that the proposed S3CM topology achieves switch count reduction. The operation of the proposed topology is validated through circuit analysis followed by experimental results of a single module (9-level) prototype.
Performance enhancement of actively controlled hybrid dc microgrid incorporat...
In this paper, a new energy control scheme is proposed for actively controlled hybrid dc microgrid to reduce the adverse impact of pulsed power loads. The proposed energy control is an adaptive current-voltage control (ACVC) scheme based on the moving average measurement technique and an adaptive proportional compensator. Unlike conventional energy control methods, the proposed ACVC approach has the advantage of controlling both voltage and current of the system while keeping the output current of the power converter at a relatively constant value. For this study, a laboratory scale hybrid dc microgrid is developed to evaluate the performance of the ACVC strategy and to compare its performance with the other conventional energy control methods. Using experimental test results, it is shown that the proposed strategy highly improves the dynamic performance of the hybrid dc microgrid. Although the ACVC technique causes slightly more bus voltage variation, it effectively eliminates the high current and power pulsation of the power converters. The experimental test results for different pulse duty ratios demonstrated a significant improvement achieved by the developed ACVC scheme in enhancing the system efficiency, reducing the ac grid voltage drop and the frequency fluctuations.
Maximum power extraction from wind energy system based on fuzzy logic control
This paper proposes a variable speed control scheme for grid-connected wind energy conversion system (WECS) using permanent magnet synchronous generator (PMSG). The control algorithm tracks the maximum power for wind speeds below rated speed of wind turbines and ensures the power will not go over the rated power for wind speeds over the rated value. The control algorithm employs fuzzy logic controller (FLC) to effectively do this target. The wind turbine is connected to the grid via back-to-back PWM-VSC. Two effective computer simulation packages (PSIM and Simulink) are used to carry out the simulation effectively. The control system has two controllers for generator side and grid side converters. The main function of the generator side controller is to track the maximum power through controlling the rotational speed of the wind turbine using FLC. In the grid side converter, active and reactive power control has been achieved by controlling q-axis and d-axis current components, respectively. The d-axis current is set at zero for unity power factor and the q-axis current is controlled to deliver the power flowing from the dc-link to the electric utility grid.
Recommended
Design and Control of Wind integrated Shunt Active Power Filter to Improve Po...
In this paper wind energy conservation system (WECS) with shunt active power filter (SAPF) is proposed for harmonics elimination, power factor correction, reactive power compensation and grid current balancing. Adaptive neuro fuzzy inference system (ANFIS) based controller is implemented at WECS side to control the boost converter to achieve MPP and at SAPF sides to minimize voltage variations and enhance power quality. Here, synchronous reference frame (SRF) theory based reference current generation technique is employed in SAPF. The proposed scheme is implemented in MATLAB/Simulink. The results confirm that this method has better performance and can maintain total harmonic distortion (THD) level of the system within the IEEE standard 519.
Power quality improvement in utility interactive based ac dc converter using ...
This paper highlights the power quality issues and explains the remedial measures taken by means of hybrid front-end third harmonic current injection rectifiers. Here zig-zag transformer is used as the current injection device so that the advantages pertaining to the zig-zag transformer is effectively utilized. The third harmonic current injection device along with three-level boost converter at the output stage will increase the DC-link voltage. With less boost inductance, generally half of the conventional boost converter inductance is sufficient to implement the proposed converter structure resulting in reduced ripple current and also the device rating is reduced by half of the output voltage. Moreover, the power quality is well improved using third harmonic current modulated front-end structure which is well appropriate for medium/higher power applications. The experimental prototype of hybrid front-end converter is developed in the laboratory to validate the MATLAB simulation results.
A three phase grid tied spv system with adaptive dc link voltage for cpi volt...
This paper deals with a three-phase two-stage grid tied SPV (solar photo-voltaic) system. The first stage is a boost converter, which serves the purpose of MPPT (maximum power point tracking) and feeding the extracted solar energy to the DC link of the PV inverter, whereas the second stage is a two-level VSC (voltage source converter) serving as PV inverter which feeds power from a boost converter into the grid. The proposed system uses an adaptive DC link voltage which is made adaptive by adjusting reference DC link voltage according to CPI (common point of interconnection) voltage. The adaptive DC link voltage control helps in the reduction of switching power losses. A feed forward term for solar contribution is used to improve the dynamic response. The system is tested considering realistic grid voltage variations for under voltage and over voltage. The performance improvement is verified experimentally. The proposed system is advantageous not only in cases of frequent and sustained under voltage (as in the cases of far radial ends of Indian grid) but also in case of normal voltages at CPI. The THD (total harmonics distortion) of grid current has been found well under the limit of an IEEE-519 standard.
An f p q droop control in cascaded-type microgrid
In cascaded-type microgrid, the synchronization and power balance of distributed generators become two new issues that needs to be addressed urgently. To that end, an f-P/Q droop control is proposed in this letter, and its stability is analyzed as well. This proposed droop control is capable to achieve power balance under both resistive-inductive an resistive-capacitive loads autonomously. Compared with the inverse power factor droop control, an obvious advantage consists in extending the scope of application. Finally, the feasibility of the proposed method is verified by simulation results.
Designing of Multilevel DPFC to Improve Power Quality
According to growth of electricity demand and the increased number of non-linear loads in power grids, providing a high quality electrical power should be considered. In this paper, Enhancement of power quality by using fuzzy based multilevel power flow controller (DPFC) is proposed. The DPFC is a new FACTS device, which its structure is similar to unified power flow controller (UPFC). In spite of UPFC, in DPFC the common dc-link between the shunt and series converters is eliminated and three-phase series converter is divided to several single-phase series distributed converters through the line. This eventually enables the DPFC to fully control all power system parameters. It, also, increases the reliability of the device and reduces its cost simultaneously. In recent years multi level inverters are used high power and high voltage applications .Multilevel inverter output voltage produce a staircase output waveform, this waveform look like a sinusoidal waveform leads to reduction in Harmonics. Fuzzy Logic is used for optimal designing of controller parameters. Application of Fuzzy Multilevel DPFC for reduction of Total Harmonic Distortion was presented. The simulation results show the improvement of power quality using DPFC with Fuzzy logic controller.
Single-Stage Switched-Capacitor Module (S3CM) Topology for Cascaded Multileve...
A two-stage switched-capacitor based multilevel inverter possesses a drawback such that switches in the second stage (i.e. H-bridge) endure higher voltage stress. To resolve this problem, this letter proposes a single-stage switched-capacitor module (S3CM) topology for cascaded multilevel inverter which ensures the peak inverse voltage across all switches within the dc source voltage. Nine voltage levels can be generated with only one dc source and two incorporated capacitors. Hence, the number of isolated dc sources are significantly reduced compared to cascaded H-bridge. In addition, voltage boosting gain of two is achieved. A comparative analysis against the recent topology reveals that the proposed S3CM topology achieves switch count reduction. The operation of the proposed topology is validated through circuit analysis followed by experimental results of a single module (9-level) prototype.
Performance enhancement of actively controlled hybrid dc microgrid incorporat...
In this paper, a new energy control scheme is proposed for actively controlled hybrid dc microgrid to reduce the adverse impact of pulsed power loads. The proposed energy control is an adaptive current-voltage control (ACVC) scheme based on the moving average measurement technique and an adaptive proportional compensator. Unlike conventional energy control methods, the proposed ACVC approach has the advantage of controlling both voltage and current of the system while keeping the output current of the power converter at a relatively constant value. For this study, a laboratory scale hybrid dc microgrid is developed to evaluate the performance of the ACVC strategy and to compare its performance with the other conventional energy control methods. Using experimental test results, it is shown that the proposed strategy highly improves the dynamic performance of the hybrid dc microgrid. Although the ACVC technique causes slightly more bus voltage variation, it effectively eliminates the high current and power pulsation of the power converters. The experimental test results for different pulse duty ratios demonstrated a significant improvement achieved by the developed ACVC scheme in enhancing the system efficiency, reducing the ac grid voltage drop and the frequency fluctuations.
Maximum power extraction from wind energy system based on fuzzy logic control
This paper proposes a variable speed control scheme for grid-connected wind energy conversion system (WECS) using permanent magnet synchronous generator (PMSG). The control algorithm tracks the maximum power for wind speeds below rated speed of wind turbines and ensures the power will not go over the rated power for wind speeds over the rated value. The control algorithm employs fuzzy logic controller (FLC) to effectively do this target. The wind turbine is connected to the grid via back-to-back PWM-VSC. Two effective computer simulation packages (PSIM and Simulink) are used to carry out the simulation effectively. The control system has two controllers for generator side and grid side converters. The main function of the generator side controller is to track the maximum power through controlling the rotational speed of the wind turbine using FLC. In the grid side converter, active and reactive power control has been achieved by controlling q-axis and d-axis current components, respectively. The d-axis current is set at zero for unity power factor and the q-axis current is controlled to deliver the power flowing from the dc-link to the electric utility grid.
Single Phase 21 Level Asymmetric Cascaded Multilevel Inverter With Reduced Nu...
Multilevel inverter technology has emerged as a very important alternative in the field of medium and high power industrial drive applications. The emergence of multilevel inverters has been increasing since three decades. These new types of converters are suitable for high voltage and high power application due to their ability to synthesize waveforms with better harmonic spectrum. Several multilevel converter topologies have been developed; i) diode clamped, ii) flying capacitors, and iii) cascaded or H-bridge. Cascade Multilevel Inverter (CMI) is one of the productive topology from multilevel family. By increasing the number of output voltage levels in multilevel inverter the Total Harmonic Distortion (THD) can be minimized. This project proposes a new topology of 21 level asymmetric cascaded multilevel inverter with 11 unidirectional switches and 3 diodes and 4 DC voltages sources. Several Pulse Width Modulation techniques are available, among them Level shifting SPWM techniques such as PO, POD and Space Vector PWM are used and comparison is shown on the basis of THDs obtained. MATLAB/ SIMULINK software is used for simulation
Matlab-based Simulation & Analysis of Three level SPWM Inverter
The multilevel began with the three level converters. The elementary concept of a multilevel converter to achieve higher power to use a series of power semiconductor switches with several lower voltage dc source to perform the power conversion by synthesizing a staircase voltage waveform. However, the output voltage is smoother with a three level converter, in which the output voltage has three possible values. This results in smaller harmonics, but on the other hand it has more components and is more complex to control. In this paper, different three level inverter topologies and SPWM technique has been applied to formulate the switching pattern for three level inverter that minimize the harmonic distortion at the inverter output. Simulation result has discussed.
Power quality improvement in distribution network using DSTATCOM with battery...
The distribution static compensator (DSTATCOM) provides fast control of active and reactive powers to enable load compensation, harmonics current elimination, voltage flicker mitigation, voltage and frequency regulation. This paper presents power quality improvement technique in the presence of grid disturbances and wind energy penetration using DSTATCOM with battery energy storage system. DSTATCOM control is provided based on synchronous reference frame theory. A modified IEEE 13 bus test feeder with DSTATCOM and wind generator is used for the study. Power quality events during grid disturbances such as feeder tripping and re-closing, voltage sag, swell and load switching have been studied in association with DSTATCOM. The power quality disturbances due to wind generator outage, synchronization and wind speed variations have also been investigated. The study has been carried out using MATLAB/SIMULINK and the simulation results are compared with real time results obtained by the use of real time digital simulator (RTDS) for validating the effectiveness of proposed methodology. The proposed method has been proved to be effective in improvement of power quality with all disturbances stated above.
A PWM Strategy Based on State Transition for Cascaded H-Bridge Inverter under...
Cascaded H-bridge converter has been widely used and researched in industry, since it is suitable for the operation under both normal and fault conditions. This paper proposes a novel PWM strategy based on state transition for cascaded H-Bridge inverter with unbalanced DC sources to achieve high quality line-to-line output voltages and maximize the linear modulation range. In this modulation strategy, the duration time of each switching state will be modified directly through the correction value. Ranges of correction value are derived by analyzing the modulation index limitation. Then, proper correction value is added into duration times to transform the switching states and extend modulation index to the maximum value. Meanwhile, balanced AC currents can be obtained under unbalanced DC sources condition, even under larger unbalanced coefficients. Furthermore, a three-phase power control algorithm (PCA) is introduced to achieve the balanced distribution of three-phase power. Compared with the traditional zero-sequence voltage injection method, the proposed strategy is more convenient and effective theoretically, and it can be applied to the higher-level cascaded H-bridge converter. The advantage and effectiveness of the proposed strategy are verified by simulation and experiment results.
A Simplified Space Vector Pulse-Width Modulation Scheme for Three-Phase Casca...
A simplified space vector pulse-width modulation (SVPWM) for three-phase cascaded H-bridge (CHB) inverters is presented in this paper. Treating each unit as a three-level inverter and adopting serial calculation mode, a CHB inverter is modulated unit by unit using three-level SVPWM. Duty cycles of real sector are obtained by mapping duty cycles of sector 1, in which the calculation of three-level SVPWM is done. The process to implement multilevel SVPWM is simplified to the process to implement three-level SVPWM. By reusing FPGA chip resource which is used for the calculation of three-level SVPWM, the presented SVPWM can be easily adopted to a CHB inverter with different number of units, while the FPGA chip resource utilization is reduced significantly. In addition, the presented SVPWM provides an effective switching frequency higher than the switching frequency of IGBTs. Simulation and experimental results are provided to verify the feasibility of the presented SVPWM.
Single-Stage Power-Factor-Correction Circuit with Flyback Converter to Drive ...
White light emitting diode (LED) with high brightness has attracted a lot of attention from both
industry and academia for its high efficiency, ease to drive, environmental friendliness, and long
lifespan. They become possible applications to replace the incandescent bulbs and fluorescent
lamps in residential, industrial and commercial lighting. The realization of this new lighting
source requires both tight LED voltage regulation and high power factor as well. This paper
proposed a single-stage flyback converter for the LED lighting applications and input power
factor correction. A type-II compensator has been inserted in the voltage loop providing
sufficient bandwidth and stable phase margin. The flyback converter is controlled with voltage
mode pulse width modulation (PWM) and run in discontinuous conduction mode (DCM) so that
the inductor current follows the rectified input voltage, resulting in high power factor. A
prototype topology of closed-loop, single stage flyback converter for LED driver circuit designed
for an 18W LED lighting source is constructed and tested to verify the theoretical predictions.
The measured performance of the LED lighting fixture can achieve a high power factor greater
than 0.998 and a low total harmonic distortion less than 5.0%. Experimental results show the
functionality of the overall system and prove it to be an effective solution for the new lighting
applications.
Combination Analysis and Switching Method of a Cascaded H-Bridge Multilevel I...
This paper analyzes the combination in a cascaded H-bridge multilevel inverter (CHBI) based on transformers with the different turn ratios for increasing the voltage level and proposes the switching method for achieving the output voltage distribution among H-bridge cells (HBCs). The transformers used in this paper are connected to the output of the respective HBCs, and the secondary sides of all the transformers are connected in series for generating the final output voltage. Only one of the transformers, in particular, has a different turn ratio for increasing the output voltage level. In this paper, the possible turn ratio of the special transformer with a different turn ratio is discussed in detail, and a switching method based on the level-shifted switching method for the topology used in this paper is proposed. To verify the effectiveness of the proposed method, a three-phase 21-level CHBI is experimentally tested.
An efficient modified cuk converter with fuzzy based maximum power point trac...
To improve the performance of photovoltaic system a modified cuk converter with Maximum Power Point Tracker (MPPT) that uses a fuzzy logic control algorithm is presented in this research work. In the proposed cuk converter, the conduction losses and switching losses are reduced by means of replacing the passive elements with switched capacitors. These switched capacitors are used to provide smooth transition of voltage and current. So, the conversion efficiency of the converter is improved and the efficiency of the PV system is increased. The PV systems use a MPPT to continuously extract the highest possible power and deliver it to the load. MPPT consists of a dc-dc converter used to find and maintain operation at the maximum power point using a tracking algorithm. The simulated results indicate that a considerable amount of additional power can be extracted from photovoltaic module using a proposed converter with fuzzy logic controller based MPPT
An efficient high step-up interleaved dc dc converter with a common active c...
This paper presents a high-efficiency and high-step up non isolated interleaved dc–dc converter with a common active clamp circuit. In the presented converter, the coupled-inductor boost converters are interleaved. A boost converter is used to clamp the voltage stresses of all the switches in the interleaved converters, caused by the leakage inductances present in the practical coupled inductors, to a low voltage level. The leakage energies of the interleaved converters are collected in a clamp capacitor and recycled to the output by the clamp boost converter. The proposed converter achieves high efficiency because of the recycling of the leakage energies, reduction of the switch voltage stress, mitigation of the output diode’s reverse recovery problem, and interleaving of the converters. Detailed analysis and design of the proposed converter are carried out. A prototype of the proposed converter is developed, and its experimental results are presented for validation.
A New Switched-Capacitor Five-Level Inverter Suitable for Transformerless Gri...
Transformerless grid-connected inverters have been extensively popular in renewable energy-based applications owing to some interesting features like higher efficiency, reasonable cost and acceptable power density. The major concern of such converters is the leakage current problem and also the step-down feature of the output voltage which causes a costly operation for a single stage energy conversion system. A new five-level transformerless inverter topology is presented in this study, which is able to boost the value of the input voltage and can remove the leakage current problem through a common-grounded architecture. Here, providing the five-level of the output voltage with only six power switches is facilitated through the series-parallel switching of a switched-capacitor module. Regarding this switching conversion, the self- voltage balancing of the integrated capacitors over a full cycle of the grid’s frequency can be acquired. Additionally, to inject a tightly controlled current to the local grid, a peak current controller-based technique is employed, which can regulate both the active and reactive power support modes. Theoretical analyses besides some experimental results are also given to corroborate the correct performance of the proposed topology.
Designing of multilevel dpfc to improve power quality
According to growth of electricity demand and the increased number of non-linear loads in power grids, providing a high quality electrical power should be considered. In this paper, Enhancement of power quality by using fuzzy based multilevel power flow controller (DPFC) is proposed. The DPFC is a new FACTS device, which its structure is similar to unified power flow controller (UPFC). In spite of UPFC, in DPFC the common dc-link between the shunt and series converters is eliminated and three-phase series converter is divided to several single-phase series distributed converters through the line. This eventually enables the DPFC to fully control all power system parameters. It, also, increases the reliability of the device and reduces its cost simultaneously. In recent years multi level inverters are used high power and high voltage applications .Multilevel inverter output voltage produce a staircase output waveform, this waveform look like a sinusoidal waveform leads to reduction in Harmonics. Fuzzy Logic is used for optimal designing of controller parameters. Application of Fuzzy Multilevel DPFC for reduction of Total Harmonic Distortion was presented. The simulation results show the improvement of power quality using DPFC with Fuzzy logic controller.
Nine-level Asymmetrical Single Phase Multilevel Inverter Topology with Low sw...
This paper presents a new asymmetrical singlephase multilevel inverter topology capable of producing ninelevel output voltage with reduce device counts. In order to obtain the desired output voltage, dc sources are connected in all the combination of addition and subtraction through different switches. Proposed topology results in reduction of dc source, switch counts, losses, cost and size of the inverter. Comparison between the existing topologies shows that the proposed topology yields less component counts. Proposed topology is modeled and simulated using Matlab-Simulink software in order to verify the performance and feasibility of the circuit. A low frequency switching strategy is also proposed in this work. The results show that the proposed topology is capable to produce a nine-level output voltage with less number of component counts and acceptable harmonic distortion content.
A multi cell 21-level hybrid multilevel inverter synthesizes a reduced number...
A multi-cell hybrid 21-Level multilevel inverter is proposed in this paper. The proposed topology includes two-unit; an H-bridge is cascaded with a modified K-type unit to generate an output voltage waveform with 21 levels based only on two unequal DC suppliers. The proposed topology's advantage lies in the fine and clear output voltage waveforms with high output efficiency. Meanwhile, the high number of output voltage waveform levels generates a low level of distortion and reduces the level of an electromagnetic interface (EMI). Moreover, it reduces the voltage stress on the switching devices and gives it a long lifetime. Also, the reduction in the number of components has a noticeable role in saving size and cost. Regarding the capacitors charging, the proposed topology presents an online method for charging and balancing the capacitor's voltage without any auxiliary circuits. The proposed topology can upgrade to a high number of output steps through the cascading connection. Undoubtedly this cascading will increase the power level to medium and high levels and reduce the harmonics content to a neglectable rate. The proposed system has been tested through the simulation results, and an experimental prototype based on the controller dSPACE (DS-1103) hardware unit used to support the simulation results.
Voltage Sag and Swell Mitigation Using DSTATCOM in Renewable Energy Based Dis...
Renewable distributed generation systems are an alternative solution to provide energy locally near customers. However, the supplying of power without disturbance is the main challenge for utilities, especially for systems that integrate fluctuating renewable sources which can cause voltage sag and swell. In this paper, voltage sag and swell issues are investigated. The first studied scenario is related to the disturbance of the energy source and the second one is due to the installation of a heavy load with a sensitive load at the same supplying bus. A D-STATCOM is connected at the point of common coupling (pCC) to mitigate the voltage sag and sell problems. An energy storage battery has been installed at the DC-side of the compensator that gives the possibility to control the voltage at the PCC and exchange the active and reactive power with the grid. A linear proportional integral (PI) feed-forward controller supervises the compensator. The obtained results show that the D-STATCOM compensator behaves as a good solution to mitigate the voltage sag and swell in distribution grid.
Sensorless bldc motor commutation point detection and phase deviation correct...
Phase-to-neutral voltage or neutral-to-virtual neutral voltage zero-crossing points (ZCPs) detection method is usually used for sensorless BLDC motor commutation control. Unfortunately, neither of them can be realized in lower speed range. In this paper, a simple commutation point detection method is proposed based on detecting inactive phase terminal to dc-link midpoint voltage. It eliminates the requirement of neutral wire or virtual neutral voltage and provides an amplified version of back electromotive force (EMF) at the ZCPs which makes the lower speed range detection possible. As the speed increasing, commutation point error is enlarged due to the low pass filter (LPF) et al. Utilizing the symmetry of the terminal to midpoint voltage the phase error can be corrected. However, due to the nonlinear relationship between the detected voltage difference and phase error, it is difficult to regulate the error fast and robustly. Therefore, a novel phase regulator based on fuzzy neural network (FNN) is proposed in this paper with simple structure and learning ability. The validity of the proposed ZCPs detection method and commutation instant shift correction method are verified through experimental results.
Voltage sag enhancement of grid connected hybrid pv wind power system using b...
Renewable energy sources; which are abundant in nature and climate friendly are the only preferable choice of the world to provide green energy. The limitation of most renewable energy sources specifically wind and solar PV is its intermittent nature which are depend on wind speed and solar irradiance respectively and this leads to power fluctuations. To compensate and protect sensitive loads from being affected by the power distribution side fluctuations and faults, dynamic voltage restorer (DVR) is commonly used. This research work attempts to withstand and secure the effect of voltage fluctuation of grid connected hybrid PV-wind power system. To do so battery and super magnetic energy storage (SMES) based DVR is used as a compensating device in case of voltage sag condition. The compensation method used is a pre-sag compensation which locks the instantaneous real time three phase voltage magnitude and angle in normal condition at the point of common coupling (PCC) and stores independently so that during a disturbance it used for compensation. Symmetrical and asymmetrical voltage sags scenario are considered and compensation is carried out using Power System Computer Aided Design or Electro Magnetic Transient Design and Control (PSCAD/EMTDC) software.
Solar grid tied inverter, with battery back-up, for efficient solar energy ha...
Solar Grid-Tied Inverter system is an electricity generating system that is connected to the utility grid. This paper discusses the design of a Grid-Tied Inverter (GTI). The first stage is Maximum Power Point Tracking (MPPT) which is implemented using perturb and observe algorithm. Then push pull converter is used to convert DC output from MPPT stage to 330V dc. This DC voltage is then converted into AC voltage using full-wave inverter topology employing unipolar SPWM technique. Then synchronization is achieved between grid and photovoltaic system. Finally, power flow control mechanism controls the power flow from GTI system to the grid and the house load.
A Variable DC Link based Novel Multilevel Inverter Topology for Low Voltage A...
In this paper; a variable dc link based novel multilevel inverter (MLI) topology is proposed. This proposed topology comprises two variable dc links and a modified H-bridge unit. This new single-phase topology offers advantages such as reduction in count of switches; gate drivers and dc sources while simultaneously improving the power quality. The proposed topology has been analyzed for both symmetric and asymmetric modes of operation. A comparative study of the proposed topology with some recent MLI topologies has been presented. The comparative study indicates that the proposed topology requires less number of dc sources; switches and driver circuits as compared to other topologies. The proposed topology has been simulated for 31- level asymmetric configuration in MATLAB/SIMULINK environment to verify the proper operation of proposed topology. Harmonic analysis was also performed for 31-level inverter which showed significant reduction in the total harmonic distortion (THD) for phase voltage and current waveforms. The proposed topology is suitable for low voltage applications such as standalone photovoltaic (PV) systems and hybrid electric vehicles (HEVs).
Thermal Stresses Relief Carrier-Based PWM Strategy for Single Phase Multileve...
Enhancing power cycling capability of power semiconductor devices is highly demanded in order to increase the long term reliability of multilevel inverters. Ageing of power switches and their cooling systems leads to their accelerated damage due to excess power losses and junction temperatures. Therefore, thermal stresses relief (TSR) is the most effective solution for lifetime extension of power semiconductor devices. This paper presents a new thermal stresses relief carrier-based pulse width modulation (TSRPWM) strategy for extending the lifetime of semiconductor switches in single-phase multilevel inverters. The proposed strategy benefits the inherent redundancy among switching states in multilevel inverters to optimally relieve the thermally stressed device. The proposed algorithm maintains the inverter operation without increased stresses on healthy switches and without reduction of the output power ratings. In addition, the proposed algorithm preserves voltage balance of the DC-link capacitors. The proposed strategy is validated on single phase five level T-type inverter system with considering different locations of thermal stresses detection. Experimental prototype of the selected case study is built to verify the results. Moreover, comparisons with the most featured strategies in literature are given in detail.
Novel symmetric modular hybrid multilevel inverter with reduced number of sem...
In this paper, by using a modular hybrid structure, a new topology for symmetric multilevel inverters (MLI) with a small number of semiconductors and low voltage stress across switches is proposed. Despite many other topologies, this topology can inherently produce negative levels and zero levels without using the H-bridge. The voltage stress across a particular switch of the proposed MLI is inversely proportional to the number of the switching of that switch in a voltage period. The proposed structure is based on two types of module, that is, the f-module and the e-module. The e-module uses a capacitive voltage divider to double the number of non-zero levels. The voltages of the capacitors are approximately balanced without complex control methods. The basic structure of the proposed topology is formed by connecting the f-module and the e-module in series with each other, and the cascaded topology is developed by cascading multiple f-modules with an e-module. To investigate the proposed topology and proving its practicability, simulation results with MATLAB/Simulink, investigation of the capacitor voltages, loss calculations and experimental results are presented. A comparative study is also performed to show the merit of the new multilevel inverter over other topologies.
Comparison of Modulation Techniques for Matrix Converter
Matrix Converters can directly convert an ac power supply of fixed voltage into an ac voltage of variable amplitude and frequency. Matrix Converter is a single stage converter. The matrix converters can contribute to the realization of low volume, sinusoidal input current, bidirectional power flow and lack of bulky reactive elements. All the reasons lead to the development of matrix converter. Based on the control techniques used in the matrix converter, the performance varies. So this paper analyses the performance of matrix converter with three different modulation techniques such as PWM, SVPWM and SVM. The basic principle and switching sequence of these modulation techniques are presented in this paper. The output voltage, output current waveforms, voltage transfer ratio and THD spectrum of switching waveforms connected to RL load are analyzed by using Matlab/Simulink software. The simulated results are analyzed and show that the THD is better for SVM technique.
Hybrid topology of asymmetric cascaded multilevel inverter with renewable ene...
This paper presents a binary topology of Multimodule level inverters produce a staircase output voltage from renewable DC voltage sources. The MLI (Multi Level Inverter) Requires many number of semiconductor switches is main drawback of multilevel inverters. The MLI can be classified as two method, one is symmetric and another asymmetric converters. In symmetrical multilevel inverter can apply same voltage level to all cascaded circuit, in asymmetric multilevel inverters can be vary input source voltage at each cascaded H-bridge by using binary algorithm. In this paper, a discrete binary topology for multilevel converters is proposed using cascaded sub-multilevel Cells. This sub-multilevel converter can produce sixty three levels of voltage from five discrete DC source. The Total Harmonic Distortions (THD) is minimized by discrete binary topology. The working operation and performance of the proposed multilevel inverters studies has been verified by simulation of using SIMULINK / MA TLAB results.
More Related Content
What's hot
Single Phase 21 Level Asymmetric Cascaded Multilevel Inverter With Reduced Nu...
Multilevel inverter technology has emerged as a very important alternative in the field of medium and high power industrial drive applications. The emergence of multilevel inverters has been increasing since three decades. These new types of converters are suitable for high voltage and high power application due to their ability to synthesize waveforms with better harmonic spectrum. Several multilevel converter topologies have been developed; i) diode clamped, ii) flying capacitors, and iii) cascaded or H-bridge. Cascade Multilevel Inverter (CMI) is one of the productive topology from multilevel family. By increasing the number of output voltage levels in multilevel inverter the Total Harmonic Distortion (THD) can be minimized. This project proposes a new topology of 21 level asymmetric cascaded multilevel inverter with 11 unidirectional switches and 3 diodes and 4 DC voltages sources. Several Pulse Width Modulation techniques are available, among them Level shifting SPWM techniques such as PO, POD and Space Vector PWM are used and comparison is shown on the basis of THDs obtained. MATLAB/ SIMULINK software is used for simulation
Matlab-based Simulation & Analysis of Three level SPWM Inverter
The multilevel began with the three level converters. The elementary concept of a multilevel converter to achieve higher power to use a series of power semiconductor switches with several lower voltage dc source to perform the power conversion by synthesizing a staircase voltage waveform. However, the output voltage is smoother with a three level converter, in which the output voltage has three possible values. This results in smaller harmonics, but on the other hand it has more components and is more complex to control. In this paper, different three level inverter topologies and SPWM technique has been applied to formulate the switching pattern for three level inverter that minimize the harmonic distortion at the inverter output. Simulation result has discussed.
Power quality improvement in distribution network using DSTATCOM with battery...
The distribution static compensator (DSTATCOM) provides fast control of active and reactive powers to enable load compensation, harmonics current elimination, voltage flicker mitigation, voltage and frequency regulation. This paper presents power quality improvement technique in the presence of grid disturbances and wind energy penetration using DSTATCOM with battery energy storage system. DSTATCOM control is provided based on synchronous reference frame theory. A modified IEEE 13 bus test feeder with DSTATCOM and wind generator is used for the study. Power quality events during grid disturbances such as feeder tripping and re-closing, voltage sag, swell and load switching have been studied in association with DSTATCOM. The power quality disturbances due to wind generator outage, synchronization and wind speed variations have also been investigated. The study has been carried out using MATLAB/SIMULINK and the simulation results are compared with real time results obtained by the use of real time digital simulator (RTDS) for validating the effectiveness of proposed methodology. The proposed method has been proved to be effective in improvement of power quality with all disturbances stated above.
A PWM Strategy Based on State Transition for Cascaded H-Bridge Inverter under...
Cascaded H-bridge converter has been widely used and researched in industry, since it is suitable for the operation under both normal and fault conditions. This paper proposes a novel PWM strategy based on state transition for cascaded H-Bridge inverter with unbalanced DC sources to achieve high quality line-to-line output voltages and maximize the linear modulation range. In this modulation strategy, the duration time of each switching state will be modified directly through the correction value. Ranges of correction value are derived by analyzing the modulation index limitation. Then, proper correction value is added into duration times to transform the switching states and extend modulation index to the maximum value. Meanwhile, balanced AC currents can be obtained under unbalanced DC sources condition, even under larger unbalanced coefficients. Furthermore, a three-phase power control algorithm (PCA) is introduced to achieve the balanced distribution of three-phase power. Compared with the traditional zero-sequence voltage injection method, the proposed strategy is more convenient and effective theoretically, and it can be applied to the higher-level cascaded H-bridge converter. The advantage and effectiveness of the proposed strategy are verified by simulation and experiment results.
A Simplified Space Vector Pulse-Width Modulation Scheme for Three-Phase Casca...
A simplified space vector pulse-width modulation (SVPWM) for three-phase cascaded H-bridge (CHB) inverters is presented in this paper. Treating each unit as a three-level inverter and adopting serial calculation mode, a CHB inverter is modulated unit by unit using three-level SVPWM. Duty cycles of real sector are obtained by mapping duty cycles of sector 1, in which the calculation of three-level SVPWM is done. The process to implement multilevel SVPWM is simplified to the process to implement three-level SVPWM. By reusing FPGA chip resource which is used for the calculation of three-level SVPWM, the presented SVPWM can be easily adopted to a CHB inverter with different number of units, while the FPGA chip resource utilization is reduced significantly. In addition, the presented SVPWM provides an effective switching frequency higher than the switching frequency of IGBTs. Simulation and experimental results are provided to verify the feasibility of the presented SVPWM.
Single-Stage Power-Factor-Correction Circuit with Flyback Converter to Drive ...
White light emitting diode (LED) with high brightness has attracted a lot of attention from both
industry and academia for its high efficiency, ease to drive, environmental friendliness, and long
lifespan. They become possible applications to replace the incandescent bulbs and fluorescent
lamps in residential, industrial and commercial lighting. The realization of this new lighting
source requires both tight LED voltage regulation and high power factor as well. This paper
proposed a single-stage flyback converter for the LED lighting applications and input power
factor correction. A type-II compensator has been inserted in the voltage loop providing
sufficient bandwidth and stable phase margin. The flyback converter is controlled with voltage
mode pulse width modulation (PWM) and run in discontinuous conduction mode (DCM) so that
the inductor current follows the rectified input voltage, resulting in high power factor. A
prototype topology of closed-loop, single stage flyback converter for LED driver circuit designed
for an 18W LED lighting source is constructed and tested to verify the theoretical predictions.
The measured performance of the LED lighting fixture can achieve a high power factor greater
than 0.998 and a low total harmonic distortion less than 5.0%. Experimental results show the
functionality of the overall system and prove it to be an effective solution for the new lighting
applications.
Combination Analysis and Switching Method of a Cascaded H-Bridge Multilevel I...
This paper analyzes the combination in a cascaded H-bridge multilevel inverter (CHBI) based on transformers with the different turn ratios for increasing the voltage level and proposes the switching method for achieving the output voltage distribution among H-bridge cells (HBCs). The transformers used in this paper are connected to the output of the respective HBCs, and the secondary sides of all the transformers are connected in series for generating the final output voltage. Only one of the transformers, in particular, has a different turn ratio for increasing the output voltage level. In this paper, the possible turn ratio of the special transformer with a different turn ratio is discussed in detail, and a switching method based on the level-shifted switching method for the topology used in this paper is proposed. To verify the effectiveness of the proposed method, a three-phase 21-level CHBI is experimentally tested.
An efficient modified cuk converter with fuzzy based maximum power point trac...
To improve the performance of photovoltaic system a modified cuk converter with Maximum Power Point Tracker (MPPT) that uses a fuzzy logic control algorithm is presented in this research work. In the proposed cuk converter, the conduction losses and switching losses are reduced by means of replacing the passive elements with switched capacitors. These switched capacitors are used to provide smooth transition of voltage and current. So, the conversion efficiency of the converter is improved and the efficiency of the PV system is increased. The PV systems use a MPPT to continuously extract the highest possible power and deliver it to the load. MPPT consists of a dc-dc converter used to find and maintain operation at the maximum power point using a tracking algorithm. The simulated results indicate that a considerable amount of additional power can be extracted from photovoltaic module using a proposed converter with fuzzy logic controller based MPPT
An efficient high step-up interleaved dc dc converter with a common active c...
This paper presents a high-efficiency and high-step up non isolated interleaved dc–dc converter with a common active clamp circuit. In the presented converter, the coupled-inductor boost converters are interleaved. A boost converter is used to clamp the voltage stresses of all the switches in the interleaved converters, caused by the leakage inductances present in the practical coupled inductors, to a low voltage level. The leakage energies of the interleaved converters are collected in a clamp capacitor and recycled to the output by the clamp boost converter. The proposed converter achieves high efficiency because of the recycling of the leakage energies, reduction of the switch voltage stress, mitigation of the output diode’s reverse recovery problem, and interleaving of the converters. Detailed analysis and design of the proposed converter are carried out. A prototype of the proposed converter is developed, and its experimental results are presented for validation.
A New Switched-Capacitor Five-Level Inverter Suitable for Transformerless Gri...
Transformerless grid-connected inverters have been extensively popular in renewable energy-based applications owing to some interesting features like higher efficiency, reasonable cost and acceptable power density. The major concern of such converters is the leakage current problem and also the step-down feature of the output voltage which causes a costly operation for a single stage energy conversion system. A new five-level transformerless inverter topology is presented in this study, which is able to boost the value of the input voltage and can remove the leakage current problem through a common-grounded architecture. Here, providing the five-level of the output voltage with only six power switches is facilitated through the series-parallel switching of a switched-capacitor module. Regarding this switching conversion, the self- voltage balancing of the integrated capacitors over a full cycle of the grid’s frequency can be acquired. Additionally, to inject a tightly controlled current to the local grid, a peak current controller-based technique is employed, which can regulate both the active and reactive power support modes. Theoretical analyses besides some experimental results are also given to corroborate the correct performance of the proposed topology.
Designing of multilevel dpfc to improve power quality
According to growth of electricity demand and the increased number of non-linear loads in power grids, providing a high quality electrical power should be considered. In this paper, Enhancement of power quality by using fuzzy based multilevel power flow controller (DPFC) is proposed. The DPFC is a new FACTS device, which its structure is similar to unified power flow controller (UPFC). In spite of UPFC, in DPFC the common dc-link between the shunt and series converters is eliminated and three-phase series converter is divided to several single-phase series distributed converters through the line. This eventually enables the DPFC to fully control all power system parameters. It, also, increases the reliability of the device and reduces its cost simultaneously. In recent years multi level inverters are used high power and high voltage applications .Multilevel inverter output voltage produce a staircase output waveform, this waveform look like a sinusoidal waveform leads to reduction in Harmonics. Fuzzy Logic is used for optimal designing of controller parameters. Application of Fuzzy Multilevel DPFC for reduction of Total Harmonic Distortion was presented. The simulation results show the improvement of power quality using DPFC with Fuzzy logic controller.
Nine-level Asymmetrical Single Phase Multilevel Inverter Topology with Low sw...
This paper presents a new asymmetrical singlephase multilevel inverter topology capable of producing ninelevel output voltage with reduce device counts. In order to obtain the desired output voltage, dc sources are connected in all the combination of addition and subtraction through different switches. Proposed topology results in reduction of dc source, switch counts, losses, cost and size of the inverter. Comparison between the existing topologies shows that the proposed topology yields less component counts. Proposed topology is modeled and simulated using Matlab-Simulink software in order to verify the performance and feasibility of the circuit. A low frequency switching strategy is also proposed in this work. The results show that the proposed topology is capable to produce a nine-level output voltage with less number of component counts and acceptable harmonic distortion content.
A multi cell 21-level hybrid multilevel inverter synthesizes a reduced number...
A multi-cell hybrid 21-Level multilevel inverter is proposed in this paper. The proposed topology includes two-unit; an H-bridge is cascaded with a modified K-type unit to generate an output voltage waveform with 21 levels based only on two unequal DC suppliers. The proposed topology's advantage lies in the fine and clear output voltage waveforms with high output efficiency. Meanwhile, the high number of output voltage waveform levels generates a low level of distortion and reduces the level of an electromagnetic interface (EMI). Moreover, it reduces the voltage stress on the switching devices and gives it a long lifetime. Also, the reduction in the number of components has a noticeable role in saving size and cost. Regarding the capacitors charging, the proposed topology presents an online method for charging and balancing the capacitor's voltage without any auxiliary circuits. The proposed topology can upgrade to a high number of output steps through the cascading connection. Undoubtedly this cascading will increase the power level to medium and high levels and reduce the harmonics content to a neglectable rate. The proposed system has been tested through the simulation results, and an experimental prototype based on the controller dSPACE (DS-1103) hardware unit used to support the simulation results.
Voltage Sag and Swell Mitigation Using DSTATCOM in Renewable Energy Based Dis...
Renewable distributed generation systems are an alternative solution to provide energy locally near customers. However, the supplying of power without disturbance is the main challenge for utilities, especially for systems that integrate fluctuating renewable sources which can cause voltage sag and swell. In this paper, voltage sag and swell issues are investigated. The first studied scenario is related to the disturbance of the energy source and the second one is due to the installation of a heavy load with a sensitive load at the same supplying bus. A D-STATCOM is connected at the point of common coupling (pCC) to mitigate the voltage sag and sell problems. An energy storage battery has been installed at the DC-side of the compensator that gives the possibility to control the voltage at the PCC and exchange the active and reactive power with the grid. A linear proportional integral (PI) feed-forward controller supervises the compensator. The obtained results show that the D-STATCOM compensator behaves as a good solution to mitigate the voltage sag and swell in distribution grid.
Sensorless bldc motor commutation point detection and phase deviation correct...
Phase-to-neutral voltage or neutral-to-virtual neutral voltage zero-crossing points (ZCPs) detection method is usually used for sensorless BLDC motor commutation control. Unfortunately, neither of them can be realized in lower speed range. In this paper, a simple commutation point detection method is proposed based on detecting inactive phase terminal to dc-link midpoint voltage. It eliminates the requirement of neutral wire or virtual neutral voltage and provides an amplified version of back electromotive force (EMF) at the ZCPs which makes the lower speed range detection possible. As the speed increasing, commutation point error is enlarged due to the low pass filter (LPF) et al. Utilizing the symmetry of the terminal to midpoint voltage the phase error can be corrected. However, due to the nonlinear relationship between the detected voltage difference and phase error, it is difficult to regulate the error fast and robustly. Therefore, a novel phase regulator based on fuzzy neural network (FNN) is proposed in this paper with simple structure and learning ability. The validity of the proposed ZCPs detection method and commutation instant shift correction method are verified through experimental results.
Voltage sag enhancement of grid connected hybrid pv wind power system using b...
Renewable energy sources; which are abundant in nature and climate friendly are the only preferable choice of the world to provide green energy. The limitation of most renewable energy sources specifically wind and solar PV is its intermittent nature which are depend on wind speed and solar irradiance respectively and this leads to power fluctuations. To compensate and protect sensitive loads from being affected by the power distribution side fluctuations and faults, dynamic voltage restorer (DVR) is commonly used. This research work attempts to withstand and secure the effect of voltage fluctuation of grid connected hybrid PV-wind power system. To do so battery and super magnetic energy storage (SMES) based DVR is used as a compensating device in case of voltage sag condition. The compensation method used is a pre-sag compensation which locks the instantaneous real time three phase voltage magnitude and angle in normal condition at the point of common coupling (PCC) and stores independently so that during a disturbance it used for compensation. Symmetrical and asymmetrical voltage sags scenario are considered and compensation is carried out using Power System Computer Aided Design or Electro Magnetic Transient Design and Control (PSCAD/EMTDC) software.
Solar grid tied inverter, with battery back-up, for efficient solar energy ha...
Solar Grid-Tied Inverter system is an electricity generating system that is connected to the utility grid. This paper discusses the design of a Grid-Tied Inverter (GTI). The first stage is Maximum Power Point Tracking (MPPT) which is implemented using perturb and observe algorithm. Then push pull converter is used to convert DC output from MPPT stage to 330V dc. This DC voltage is then converted into AC voltage using full-wave inverter topology employing unipolar SPWM technique. Then synchronization is achieved between grid and photovoltaic system. Finally, power flow control mechanism controls the power flow from GTI system to the grid and the house load.
A Variable DC Link based Novel Multilevel Inverter Topology for Low Voltage A...
In this paper; a variable dc link based novel multilevel inverter (MLI) topology is proposed. This proposed topology comprises two variable dc links and a modified H-bridge unit. This new single-phase topology offers advantages such as reduction in count of switches; gate drivers and dc sources while simultaneously improving the power quality. The proposed topology has been analyzed for both symmetric and asymmetric modes of operation. A comparative study of the proposed topology with some recent MLI topologies has been presented. The comparative study indicates that the proposed topology requires less number of dc sources; switches and driver circuits as compared to other topologies. The proposed topology has been simulated for 31- level asymmetric configuration in MATLAB/SIMULINK environment to verify the proper operation of proposed topology. Harmonic analysis was also performed for 31-level inverter which showed significant reduction in the total harmonic distortion (THD) for phase voltage and current waveforms. The proposed topology is suitable for low voltage applications such as standalone photovoltaic (PV) systems and hybrid electric vehicles (HEVs).
Thermal Stresses Relief Carrier-Based PWM Strategy for Single Phase Multileve...
Enhancing power cycling capability of power semiconductor devices is highly demanded in order to increase the long term reliability of multilevel inverters. Ageing of power switches and their cooling systems leads to their accelerated damage due to excess power losses and junction temperatures. Therefore, thermal stresses relief (TSR) is the most effective solution for lifetime extension of power semiconductor devices. This paper presents a new thermal stresses relief carrier-based pulse width modulation (TSRPWM) strategy for extending the lifetime of semiconductor switches in single-phase multilevel inverters. The proposed strategy benefits the inherent redundancy among switching states in multilevel inverters to optimally relieve the thermally stressed device. The proposed algorithm maintains the inverter operation without increased stresses on healthy switches and without reduction of the output power ratings. In addition, the proposed algorithm preserves voltage balance of the DC-link capacitors. The proposed strategy is validated on single phase five level T-type inverter system with considering different locations of thermal stresses detection. Experimental prototype of the selected case study is built to verify the results. Moreover, comparisons with the most featured strategies in literature are given in detail.
Novel symmetric modular hybrid multilevel inverter with reduced number of sem...
In this paper, by using a modular hybrid structure, a new topology for symmetric multilevel inverters (MLI) with a small number of semiconductors and low voltage stress across switches is proposed. Despite many other topologies, this topology can inherently produce negative levels and zero levels without using the H-bridge. The voltage stress across a particular switch of the proposed MLI is inversely proportional to the number of the switching of that switch in a voltage period. The proposed structure is based on two types of module, that is, the f-module and the e-module. The e-module uses a capacitive voltage divider to double the number of non-zero levels. The voltages of the capacitors are approximately balanced without complex control methods. The basic structure of the proposed topology is formed by connecting the f-module and the e-module in series with each other, and the cascaded topology is developed by cascading multiple f-modules with an e-module. To investigate the proposed topology and proving its practicability, simulation results with MATLAB/Simulink, investigation of the capacitor voltages, loss calculations and experimental results are presented. A comparative study is also performed to show the merit of the new multilevel inverter over other topologies.
What's hot (20)
Single Phase 21 Level Asymmetric Cascaded Multilevel Inverter With Reduced Nu...
Single Phase 21 Level Asymmetric Cascaded Multilevel Inverter With Reduced Nu...
Matlab-based Simulation & Analysis of Three level SPWM Inverter
Matlab-based Simulation & Analysis of Three level SPWM Inverter
Power quality improvement in distribution network using DSTATCOM with battery...
Power quality improvement in distribution network using DSTATCOM with battery...
A PWM Strategy Based on State Transition for Cascaded H-Bridge Inverter under...
A PWM Strategy Based on State Transition for Cascaded H-Bridge Inverter under...
A Simplified Space Vector Pulse-Width Modulation Scheme for Three-Phase Casca...
A Simplified Space Vector Pulse-Width Modulation Scheme for Three-Phase Casca...
Single-Stage Power-Factor-Correction Circuit with Flyback Converter to Drive ...
Single-Stage Power-Factor-Correction Circuit with Flyback Converter to Drive ...
Combination Analysis and Switching Method of a Cascaded H-Bridge Multilevel I...
Combination Analysis and Switching Method of a Cascaded H-Bridge Multilevel I...
An efficient modified cuk converter with fuzzy based maximum power point trac...
An efficient modified cuk converter with fuzzy based maximum power point trac...
An efficient high step-up interleaved dc dc converter with a common active c...
An efficient high step-up interleaved dc dc converter with a common active c...
A New Switched-Capacitor Five-Level Inverter Suitable for Transformerless Gri...
A New Switched-Capacitor Five-Level Inverter Suitable for Transformerless Gri...
Designing of multilevel dpfc to improve power quality
Designing of multilevel dpfc to improve power quality
Nine-level Asymmetrical Single Phase Multilevel Inverter Topology with Low sw...
Nine-level Asymmetrical Single Phase Multilevel Inverter Topology with Low sw...
A multi cell 21-level hybrid multilevel inverter synthesizes a reduced number...
A multi cell 21-level hybrid multilevel inverter synthesizes a reduced number...
Voltage Sag and Swell Mitigation Using DSTATCOM in Renewable Energy Based Dis...
Voltage Sag and Swell Mitigation Using DSTATCOM in Renewable Energy Based Dis...
Sensorless bldc motor commutation point detection and phase deviation correct...
Sensorless bldc motor commutation point detection and phase deviation correct...
Voltage sag enhancement of grid connected hybrid pv wind power system using b...
Voltage sag enhancement of grid connected hybrid pv wind power system using b...
Solar grid tied inverter, with battery back-up, for efficient solar energy ha...
Solar grid tied inverter, with battery back-up, for efficient solar energy ha...
A Variable DC Link based Novel Multilevel Inverter Topology for Low Voltage A...
A Variable DC Link based Novel Multilevel Inverter Topology for Low Voltage A...
Thermal Stresses Relief Carrier-Based PWM Strategy for Single Phase Multileve...
Thermal Stresses Relief Carrier-Based PWM Strategy for Single Phase Multileve...
Novel symmetric modular hybrid multilevel inverter with reduced number of sem...
Novel symmetric modular hybrid multilevel inverter with reduced number of sem...
Similar to Critical Current Control (C3) and Modeling of a Buck Based LED Driver with Power Factor Correction
Comparison of Modulation Techniques for Matrix Converter
Matrix Converters can directly convert an ac power supply of fixed voltage into an ac voltage of variable amplitude and frequency. Matrix Converter is a single stage converter. The matrix converters can contribute to the realization of low volume, sinusoidal input current, bidirectional power flow and lack of bulky reactive elements. All the reasons lead to the development of matrix converter. Based on the control techniques used in the matrix converter, the performance varies. So this paper analyses the performance of matrix converter with three different modulation techniques such as PWM, SVPWM and SVM. The basic principle and switching sequence of these modulation techniques are presented in this paper. The output voltage, output current waveforms, voltage transfer ratio and THD spectrum of switching waveforms connected to RL load are analyzed by using Matlab/Simulink software. The simulated results are analyzed and show that the THD is better for SVM technique.
Hybrid topology of asymmetric cascaded multilevel inverter with renewable ene...
This paper presents a binary topology of Multimodule level inverters produce a staircase output voltage from renewable DC voltage sources. The MLI (Multi Level Inverter) Requires many number of semiconductor switches is main drawback of multilevel inverters. The MLI can be classified as two method, one is symmetric and another asymmetric converters. In symmetrical multilevel inverter can apply same voltage level to all cascaded circuit, in asymmetric multilevel inverters can be vary input source voltage at each cascaded H-bridge by using binary algorithm. In this paper, a discrete binary topology for multilevel converters is proposed using cascaded sub-multilevel Cells. This sub-multilevel converter can produce sixty three levels of voltage from five discrete DC source. The Total Harmonic Distortions (THD) is minimized by discrete binary topology. The working operation and performance of the proposed multilevel inverters studies has been verified by simulation of using SIMULINK / MA TLAB results.
High frequency ac-link pv inverter
In this paper, a high-frequency ac-link photovoltaic (PV) inverter is proposed. The proposed inverter overcomes most of the problems associated with currently available PV inverters. In this inverter, a single-stage power-conversion unit fulfills all the system requirements, i.e., inverting dc voltage to proper ac, stepping up or down the input voltage, maximum power point tracking, generating low-harmonic ac at the output, and input/output isolation. This inverter is, in fact, a partial resonant ac-link converter in which the link is formed by a parallel inductor/capacitor (LC) pair having alternating current and voltage. Among the significant merits of the proposed inverter are the zero-voltage turn-on and soft turn-off of the switches which result in negligible switching losses and minimum voltage stress on the switches. Hence, the frequency of the link can be as high as permitted by the switches and the processor. The high frequency of operation makes the proposed inverter very compact. The other significant advantage of the proposed inverter is that no bulky electrolytic capacitor exists at the link. Electrolytic capacitors are cited as the most unreliable component in PV inverters, and they are responsible for most of the inverters’ failures, particularly at high temperature. Therefore, substituting dc electrolytic capacitors with ac LC pairs will significantly increase the reliability of PV inverters. A 30-kW prototype was fabricated and tested. The principle of operation and detailed design procedure of the proposed inverter along with the simulation and experimental results are included in this paper. To evaluate the long-term performance of the proposed inverter, three of these inverters were installed at three different commercial facilities in Texas, USA, to support the PV systems. These inverters have been working for several months now.
Artificial Neural Network based Dynamic Voltage Restorer for Improvement of P...
Dynamic Voltage Restorer (DVR) is a custom power device used as an effective solution in protecting sensitive loads from voltage disturbances in power distribution systems. The efficiency of the control technique, that conducts the switching of the inverters, determines the DVR efficiency. Proportional-Integral-Derivative (PID) control is the general technique to do that. The power quality restoration capabilities of this controller are limited, and it produces significant amount of harmonics – all of which stems from this linear technique’s application for controlling non-linear DVR. As a solution, this paper proposes an Artificial Neural Network (ANN) based controller for enhancing restoration and harmonics suppression capabilities of DVR. A detailed comparison of Neural Network controller with PID driven controller and Fuzzy logic driven controller is also illustrated, where the proposed controller demonstrated superior performance with a mere 13.5% Total Harmonic Distortion.
Mppt with single dc–dc converter and inverter for grid connected hybrid wind-...
A new topology of a hybrid distributed generator based on photovoltaic and wind-driven permanent magnet synchronous generator is proposed. In this generator, the sources are connected together to the grid with the help of only a single boost converter followed by an inverter. Thus, compared to earlier schemes, the proposed scheme has fewer power converters. A model of the proposed scheme in the d − q-axis reference frame is developed. Two low-cost controllers are also proposed for the new hybrid scheme to separately trigger the dc–dc converter and the inverter for tracking the maximum power from both sources. The integrated operations of both proposed controllers for different conditions are demonstrated through simulation and experimentation. The steady-state performance of the system and the transient response of the controllers are also presented to demonstrate the successful operation of the new hybrid system. Comparisons of experimental and simulation results are given to validate the simulation model.
Front end buck rectifier with reduced filter size and single-loop control
This paper presents a transformerless solution for front-end rectification, which is particularly suitable for traction applications, requiring high voltages to be stepped down to appropriate dc voltage. The proposed topology is based on pulse widthmodulation buck rectifier (current source inverter topology) and is capable of rectification and stepping down of single-phase ac supply, in a single stage. A new control scheme is proposed to achieve constant dc output voltage and sinusoidal source current, irrespective of large ripples in the dc inductor current. The proposed scheme is configured in single-loop voltage control mode. The relevant small-signal model is derived from the large-signal model using multi order decomposition. An elaborate procedure of dc filter design is discussed, for circuit operation with minimum energy storage. All analytical results are validated by numerical simulation for sinusoidal and distorted source voltage. Experimental verification is achieved through a 1.2-kW grid-connected laboratory prototype.
Model predictive control of pv sources in a smart dc distribution system maxi...
In a dc distribution system, where multiple power sources supply a common bus, current sharing is an important issue. When renewable energy resources are considered, such as photovoltaic (PV), dc/dc converters are needed to decouple the source voltage, which can vary due to operating conditions and maximum power point tracking (MPPT), from the dc bus voltage. Since different sources may have different power delivery capacities that may vary with time, coordination of the interface to the bus is of paramount importance to ensure reliable system operation. Further, since these sources are most likely distributed throughout\ the system, distributed controls are needed to ensure a robust and fault tolerant control system. This paper presents a model predictive control-based MPPT and model predictive control-based droop current regulator to interface PV in smart dc distribution systems. Back-to-back dc/dc converters control both the input current from the PV module and the droop characteristic of the output current injected into the distribution bus. The predictive controller speeds up both of the control loops, since it predicts and corrects error before the switching signal is applied to the respective converter.
Reduced Sensor Based PV Array Fed Direct Torque Control Induction Motor Drive...
This paper aims at the design, control and implementation of a solar photovoltaic (PV) array fed speed sensorless direct torque control (DTC) of an induction motor drive (IMD) for water pumping in standalone as well as battery connected hybrid mode. This stator flux estimated by proposed flux observer, is used for speed estimation. A DC link current sensor is used to reconstruct the motor phase currents by modified active voltage vector. One voltage sensor for DC link voltage sensing and only one current sensor for DC link current sensing, are used in this system for standalone operation of the system. All other required quantities are estimated through these two sensed signals. The IMD is energized by a photovoltaic (PV) array, which is operated at maximum power point (MPP). A perturb and observe control algorithm with additional flow rate controller, is proposed for MPP, which tracks MPP throughout the operating range and provides the facility to control flow rate. The suitability of the system is judged through simulated results in MATLAB/Simulink as well as test results obtained on a prototype developed in the laboratory.
Single phase active power filtering method using diode-rectifier-fed motor drive
This paper presents a single-phase high power factor motor drive system with active power filter function. Since most of electrical equipment connected to the grid must comply with regulations regarding grid current harmonics, motor drive systems are generally equipped with Power Factor Corrector (PFC) which is comprised of power switches and reactive components, e.g., inductor and capacitor. The reactive components are bulky and increase the system cost especially in low-cost applications such as electrical home appliances. In this paper, a new motor drive algorithm which is capable of both driving a permanent magnet motor and filtering the harmonic currents produced by other non-linear loads belong to the system is proposed. Since the input current of the drive system is directly controlled by manipulating not the motor current reference but the output voltage reference of the inverter, it is possible to achieve exact and immediate control of the grid current. The effectiveness of the proposed algorithms is validated by experiments with a permanent magnet motor drive system.
A Unity Power Factor Converter with Isolation for Electric Vehicle Battery Ch...
This paper deals with a unity power factor (UPF) Cuk converter EV (Electric Vehicle) battery charger having a high frequency transformer isolation instead of only a single phase front end converter used in vehicle's conventional battery chargers. The operation of the proposed converter is defined in various modes of the converter components i.e. DCM (Discontinuous Conduction Mode) or CCM (Continuous Conduction Mode) along with the optimum design equations. In this way, this isolated PFC converter makes the input current sinusoidal in shape and improves input power factor to unity. Simulation results for the proposed converter are shown for charging a lead acid EV battery in constant current constant voltage (CC-CV) mode. The rated full load and varying input supply conditions have been considered to show the improved power quality indices as compared to conventional battery chargers. These indices follow the international IEC 61000-3-2 standard to give harmonic free input parameters for the proposed circuit.
Power quality enhancement in residential smart grids through power factor cor...
The proliferation of non-linear loads and the increasing penetration of Distributed Energy Resources (DER) in Medium-Voltage (MV) and Low-Voltage (LV) distribution grids, make it more difficult to maintain the power quality levels in residential electrical grids, especially in the case of weak grids. Most household appliances contain a conventional Power Factor Corrector (PFC) rectifier, which maximizes the load Power Factor (PF) but does not contribute to the regulation of the voltage Total Harmonic Distortion (THDV ) in residential electrical grids. This manuscript proposes a modification for PFC controllers by adapting the operation mode depending on the measured THDV . As a result, the PFCs operate either in a low current Total Harmonic Distortion (THDI ) mode or in the conventional resistor emulator mode and contribute to the regulation of the THDV and the PF at the distribution feeders. To prove the concept, the modification is applied to a current sensorless Non-Linear Controller (NLC) applied to a single-phase Boost rectifier. Experimental results show its performance in a PFC front-end stage operating in Continuous Conduction Mode (CCM) connected to the grid with different THDV .
Designing of multilevel dpfc to improve power quality
According to growth of electricity demand and the increased number of non-linear loads in power grids, providing a high quality electrical power should be considered. In this paper, Enhancement of power quality by using fuzzy based multilevel power flow controller (DPFC) is proposed. The DPFC is a new FACTS device, which its structure is similar to unified power flow controller (UPFC). In spite of UPFC, in DPFC the common dc-link between the shunt and series converters is eliminated and three-phase series converter is divided to several single-phase series distributed converters through the line. This eventually enables the DPFC to fully control all power system parameters. It, also, increases the reliability of the device and reduces its cost simultaneously. In recent years multi level inverters are used high power and high voltage applications .Multilevel inverter output voltage produce a staircase output waveform, this waveform look like a sinusoidal waveform leads to reduction in Harmonics. Fuzzy Logic is used for optimal designing of controller parameters. Application of Fuzzy Multilevel DPFC for reduction of Total Harmonic Distortion was presented. The simulation results show the improvement of power quality using DPFC with Fuzzy logic controller.
Permanent Magnet Synchronous Generator-Based Standalone Wind Energy Supply Sy...
In this paper, a novel algorithm, based on dc link voltage, is proposed for effective energy management of a standalone permanent magnet synchronous generator (PMSG)-based variable speed wind energy conversion system consisting of battery, fuel cell, and dump load (i.e., electrolyzer). Moreover, by maintaining the dc link voltage at its reference value, the output ac voltage of the inverter can be kept constant irrespective of variations in the wind speed and load. An effective control technique for the inverter, based on the pulse width modulation (PWM) scheme, has been developed to make the line voltages at the point of common coupling (PCC) balanced when the load is unbalanced. Similarly, a proper control of battery current through dc–dc converter has been carried out to reduce the electrical torque pulsation of the PMSG under an unbalanced load scenario. Based on extensive simulation results using MATLAB/SIMULINK, it has been established that the performance of the controllers both in transient as well as in steady state is quite satisfactory and it can also maintain maximum power point tracking.
Artificial Neural Network based Dynamic Voltage Restorer for Improvement of P...
Dynamic Voltage Restorer (DVR) is a custom power device used as an effective solution in protecting sensitive loads from voltage disturbances in power distribution systems. The efficiency of the control technique, that conducts the switching of the inverters, determines the DVR efficiency.Proportional-Integral-Derivative (PID) control is the general technique to do that. The power quality restoration capabilities of this controller are limited, and it produces significant amount of harmonics – all of which stems from this linear technique’s application for controlling non-linear DVR. As a solution, this paper proposes an Artificial Neural Network (ANN) based controller for enhancing restoration and harmonics suppression capabilities of DVR. A detailed comparison of Neural Network controller with PID driven controller and Fuzzy logic driven controller is also illustrated, where the proposed controller demonstrated superior performance with a mere 13.5% Total Harmonic Distortion.
An advanced multilevel converter topology with Reduced switching elements
Smart grid applications, renewable energy utilization and electric vehicles (EVs) are attracting researchers due to their importance nowadays as well as in the future. An efficient power electronic converter is a main and common topic for research in this area. In this paper, a prototype of the electrical part of a power-train for EVs using an advanced multilevel converter topology is introduced, discussed and analysed. A comparison between the advanced converter, two-level and conventional multilevel converter topology is discussed as well. A switch function model is derived and discussed for the proposed converter. A mathematical model for the converter supplied by a fuel-cell (FC) and boost-converter (BC) is implemented with Matlab/Simulink. The simulation results are analysed to evaluate the converter. The evaluation is based on the harmonic analysis and power loss calculations. The converters are tested at different switching frequencies to show the effect of this variable on the converter loss. The results indicate that the proposed converter is 1.32% more efficient compared to conventional five-level DCC. Moreover, the lowest harmonic content, for all of the studied converters, is the proposed one
A New Design Method of an LCL Filter Applied in Active DC-Traction Substations
This paper concentrates on the LCL filter with damping resistance intended to connect the shunt active power filter of an active DC-traction substation to the point of common coupling with the transmission grid. In order to find design conditions and conceive a design algorithm, attention is directed to the transfer functions related to currents and the associated frequency response. The mathematical foundation of the design method is based on the meeting the requirements related to the significant attenuation of the high-frequency switching current, concurrently with the unalterated flow of the current that needs to be compensated by active filtering. It is pointed out that there are practical limitations and a compromise must be made between the two requirements. To quantify the extent to which the harmonics to be compensated are influenced by imposing the magnitude response at both highest harmonic frequency to be compensated and switching frequency, a performance indicator is defined. As an additional design criterion, the damping power losses are taken into consideration. The validity and effectiveness of the proposed method are proved by simulation results and experimental tests on a laboratory test bench of small scale reproducing the specific conditions of a DC-traction substation with six-pulse diode rectifier.
Power Quality Analysis and Enhancement of Grid Connected Solar Energy System
In recent years, renewable energy resources are utilized to meet the growing energy demand. The integration of renewable energy resources with the grid incorporates power electronic converters for conversion of energy. These power electronic converters introduce power quality issues such as a harmonics, voltage regulation etc. Hence, to improve the power quality issues, this work proposes a new control strategy for a grid interconnected solar system. In this proposed work, a maximum power point tracking (MPPT) scheme has been used to obtain maximum power from the solar system and DC/DC converter is implemented to maintain a constant DC voltage. An active filtering method is utilized to improve the power quality of the grid connected solar system. The proposed system is validated through dynamic simulation using MATLAB/Simulink Power system toolbox and results are delivered to validate the effectiveness of the work.
Irradiance-adaptive PV Module Integrated Converter for High Efficiency and Po...
The strive for efficient and cost-effective photovoltaic systems motivated the power electronic design developed here. The work resulted in a DC-DC converter for module integration and distributed maximum power point tracking (MPPT) with a novel adaptive control scheme. The latter is essential for the combined features of high energy efficiency and high power quality over a wide range of operating conditions. The switching frequency is optimally modulated as a function of solar irradiance for power conversion efficiency maximization. With the rise of irradiance, the frequency is reduced to reach the conversion efficiency target. A search algorithm is developed to determine the optimal switching frequency step. Reducing the switching frequency may, however, compromise MPPT efficiency. Furthermore, it leads to increased ripple content. Therefore, to achieve a uniform high power quality at all conditions, interleaved converter cells are adaptively activated. The overall cost is kept low by selecting components that allow for implementing the functions at low cost. Simulation results show the high value of the module integrated converter for DC standalone and microgrid applications. A 400 W prototype was implemented at 0.14 Euro/W. Testing showed efficiencies above 95% taking into account all losses from power conversion, MPPT, and measurement and control circuitry.
Comprehensive Study of Single-Phase AC-DC Power Factor Corrected Converters w...
Solid-state switch mode AC-DC converters having high-frequency transformer isolation are developed in buck, boost, and buck-boost configurations with improved power quality in terms of reduced total harmonic distortion (THD) of input current, power-factor correction (PFC) at AC mains and precisely regulated and isolated DC output voltage feeding to loads from few Watts to several kW. This paper presents a comprehensive study on state of art of power factor corrected single-phase AC-DC converters configurations, control strategies, selection of components and design considerations, performance evaluation, power quality considerations, selection criteria and potential applications, latest trends, and future developments. Simulation results as well as comparative performance are presented and discussed for most of the proposed topologies.
Similar to Critical Current Control (C3) and Modeling of a Buck Based LED Driver with Power Factor Correction (20)
Comparison of Modulation Techniques for Matrix Converter
Comparison of Modulation Techniques for Matrix Converter
Hybrid topology of asymmetric cascaded multilevel inverter with renewable ene...
Hybrid topology of asymmetric cascaded multilevel inverter with renewable ene...
Artificial Neural Network based Dynamic Voltage Restorer for Improvement of P...
Artificial Neural Network based Dynamic Voltage Restorer for Improvement of P...
Mppt with single dc–dc converter and inverter for grid connected hybrid wind-...
Mppt with single dc–dc converter and inverter for grid connected hybrid wind-...
Front end buck rectifier with reduced filter size and single-loop control
Front end buck rectifier with reduced filter size and single-loop control
Model predictive control of pv sources in a smart dc distribution system maxi...
Model predictive control of pv sources in a smart dc distribution system maxi...
Reduced Sensor Based PV Array Fed Direct Torque Control Induction Motor Drive...
Reduced Sensor Based PV Array Fed Direct Torque Control Induction Motor Drive...
Single phase active power filtering method using diode-rectifier-fed motor drive
Single phase active power filtering method using diode-rectifier-fed motor drive
A Unity Power Factor Converter with Isolation for Electric Vehicle Battery Ch...
A Unity Power Factor Converter with Isolation for Electric Vehicle Battery Ch...
Dynamic behavior of DFIG wind turbine under grid fault conditions (1)
Dynamic behavior of DFIG wind turbine under grid fault conditions (1)
Power quality enhancement in residential smart grids through power factor cor...
Power quality enhancement in residential smart grids through power factor cor...
Designing of multilevel dpfc to improve power quality
Designing of multilevel dpfc to improve power quality
Permanent Magnet Synchronous Generator-Based Standalone Wind Energy Supply Sy...
Permanent Magnet Synchronous Generator-Based Standalone Wind Energy Supply Sy...
Artificial Neural Network based Dynamic Voltage Restorer for Improvement of P...
Artificial Neural Network based Dynamic Voltage Restorer for Improvement of P...
An advanced multilevel converter topology with Reduced switching elements
An advanced multilevel converter topology with Reduced switching elements
A New Design Method of an LCL Filter Applied in Active DC-Traction Substations
A New Design Method of an LCL Filter Applied in Active DC-Traction Substations
Power Quality Analysis and Enhancement of Grid Connected Solar Energy System
Power Quality Analysis and Enhancement of Grid Connected Solar Energy System
Irradiance-adaptive PV Module Integrated Converter for High Efficiency and Po...
Irradiance-adaptive PV Module Integrated Converter for High Efficiency and Po...
Comprehensive Study of Single-Phase AC-DC Power Factor Corrected Converters w...
Comprehensive Study of Single-Phase AC-DC Power Factor Corrected Converters w...
More from Asoka Technologies
Solar pv charging station for electric vehicles
Of late, electric vehicles (EVs) have attracted much attention owing to their use of clean energy. Large progress in lithium-ion battery has propelled the development of EVs.However, the challenge is that growing number of EVs leads to huge demand in electric power, which will aggravate the power grid load. This leads to an exploration for alternative and clean sources of energy to charge EVs. This project implements solar energy system to erect a charging station for EV application. The charging station employs multi-port charging by providing a constant voltage DC bus. The charging controllers are operated based on the concept of power balance, and constant current/constant voltage charging. Performance of the charging system is validated with simulation and experimental results.
Generation of Higher Number of Voltage Levels by Stacking Inverters of Lower ...
This paper proposes a new method of generating higher number of levels in the voltage waveform by stacking multilevel converters with lower voltage space vector structures. An important feature of this stacked structure is the use of low voltage devices while attaining higher number of levels. This will find extensive applications in electric vehicles since direct battery drive is possible. The voltages of all the capacitors in the structure can be controlled within a switching cycle using the switching state redundancies (pole voltage redundancies). This helps in reducing the capacitor size. Also, the capacitor voltages can be balanced irrespective of modulation index and load power factor. To verify the concept experimentally, a 9-level inverter is developed by stacking two 5-level inverters and an induction motor is run using V/f control scheme. Both steady state and transient results are presented.
A New Family of Step-up Hybrid Switched- Capacitor Integrated Multilevel Inve...
In the low voltage based renewable systems like PV and Fuel cell applications, the step-up of the output voltage to drive the loads is essential. For this, the integration of switched-capacitor (SC) units with the dc-ac converters will have the potential advantages like improved efficiency, optimal switching devices, small size of passive elements (L and C) as compared with traditional two-stage conversion system (dc/dc converter and dc/ac converter). This paper focuses on a new family of step-up multilevel inverter topologies with switched capacitor integration with dual input voltage sources. With the flexibility of 2 dc sources and switching capacitor circuits, four different topologies have been suggested in this paper with features of high voltage gain, reduced component count, reduced voltage stress and self-voltage balancing of the capacitor while achieving a higher number of levels. A detailed analysis of proposed multilevel inverters has been analyzed with the symmetrical and asymmetrical mode of operations and the associated gain, the number of levels, and other performance indices are presented. An in-depth study of all the topologies has been accomplished in this paper with several comparative studies in terms of components count, voltage gain and cost. The effectiveness and practicability of the suggested topology with 13 level output voltage has been explained by the experimental results obtained from a scale down prototype.
A generalized multilevel inverter topology with reduction of total standing v...
This paper presents a new multilevel inverter topology with reduced active switches and total standing voltage. The proposed topology can generate a high number of voltage levels in the symmetric configuration. This topology intuitively generates positive and negative cycles without an additional H-bridge unit, which considerably reduces the total standing voltage of the inverter. A cascaded structure is developed from the proposed topology to create higher voltage levels. To show the novelty of the proposed topology, a thorough comparison between the available and the proposed topologies in terms of the number of switches, standing voltages, and dc-sources is presented. Furthermore, the power loss analysis is carried out for various load values. The feasibility of the proposed nine-level inverter is verified with simulation and experimental results.
Power Quality Improvement in Solar Fed Cascaded Multilevel Inverter with Outp...
The presence of harmonics in solar Photo Voltaic (PV) energy conversion system results in deterioration of power quality. To address such issue, this paper aims to investigate the elimination of harmonics in a solar fed cascaded fifteen level inverter with aid of Proportional Integral (PI), Artificial Neural Network (ANN) and Fuzzy Logic (FL) based controllers. Unlike other techniques, the proposed FLC based approach helps in obtaining reduced harmonic distortions that intend to an enhancement in power quality. In addition to the power quality improvement, this paper also proposed to provide output voltage regulation in terms of maintaining voltage and frequency at the inverter output end in compatible with the grid connection requirements. The simulations are performed in the MATLAB / Simulink environment for solar fed cascaded 15 level inverter incorporating PI, ANN and FL based controllers. To exhibit the proposed technique, a 3 kWp photovoltaic plant coupled to multilevel inverter is designed and hardware is demonstrated. All the three techniques are experimentally investigated with the measurement of power quality metrics along with establishing output voltage regulation.
Residential Community Load Management based on Optimal Design of Standalone H...
Microgrids being an important entity in the distribution system, and to get their full advantages
by incorporating maximum distributed generation, standalone hybrid renewable energy systems (HRESs), being environmentally-safe and economically-efficient, are considered as the promising solution to electrify remote areas where the grid power is not available. In this work, a techno-economic investigation with an optimal design of HRES is presented to fulfill the domestic electricity need for a residential area of the Sherani district in the Province of Baluchistan, Pakistan. Nine case studies based on PV/wind/diesel/battery are analyzed based on net present cost (NPC), cost of energy (COE), and emission to decide the feasible solution. HOMER tool is utilized to accomplish modeling and simulation for economic analysis and optimal sizing. Simulation results demonstrated that HRES with PV-wind-battery is the most viable option for the specified area, and the optimal sizing of components are also obtained with $ 28,620 NPC and 0.311 $/kWh COE which shows 81.65% reduction in cost and 100% preserving in toxic emission while fulfilling 100% energy demand with 67.3% of excess energy. Furthermore, MATLAB/Simulink modeling for the optimally designed system is built for technical analysis while its effectiveness is proved by keeping dc and ac buses voltage constant, safe operating range of battery state of charge (SOC) with active power balance between HRES components, as well as efficient ac voltage quality, regardless of generation disturbances and load fluctuations. The output signal has total harmonic distortion (THD) of 0.30% as compared to 5.44% with the conventional control scheme. The novelty lies in the sequential application of both HOMER and MATLAB simulations of the proposed HRES model and validation of the proposition for the studied area; by using and implementing model predictive control (MPC) of a reconfigurable inverter.
Reliability evaluation of MPPT based interleaved boost converter for PV system
The demand for power supply and depletion of the conventional energy sources are increasing drastically. So to overcome this problem, the best alternative power generation for conventional fossil fuel is Photovoltaic solar cell based system because of its advantage of pollution free and its availability in abundance with free of cost. In the MPPT based PV system the converters are the most sensitive part. Therefore to provide uninterrupted power supply without compromising the quality of power, reliability evaluation of interleaved boost converter becomes necessary. MATLAB/Simulink is used for the simulation studies and to determine the power losses of various components of the converter which is used in calculating the failure rates and reliability of the interleaved boost converter. Reliability studies of IBC have not been studied much. However there exists few literature in which reliability expression has been developed using Markov technique which is a more complex method as compare to Reliability Block Diagram (RBD). Therefore this paper proposes reliability modeling and reliability evaluation of Interleaved boost converter in MPPT based photo-voltaic system by using simple RBD method.
Power Quality Improvement of Grid-Connected Photovoltaic Systems Using Trans-...
Voltage-source inverter has been used widely in traditional photovoltaic systems which have limitations. To overcome, Z-source inverter has been introduced. In spite of all the features introduced in Z-source inverter, its configuration has been improved over the years, like trans-Z-source inverter which has added advantages compared to traditional inverters, namely buck–boost feature, lesser passive elements, and higher voltage boost gain. In this paper, photovoltaic arrays are connected to the grid via the trans-Z-source inverter with the aim of improving its power quality. Moreover, the shoot through duty ratio is kept constant in the switching control method to add features like lower voltage stress (higher reliability), lower total harmonic distortion (lower maintenance cost), and higher voltage boost ratio. To evaluate the precision of the proposed system, the photovoltaic system is simulated on a standard grid and under partial shading condition which brings about voltage sag, and hence, a dynamic voltage restorer is used to mitigate voltage sag. Simulation results are presented to verify the validation of the proposed photovoltaic system in terms of voltage and current THD reducing 78.2% and 19.7%, respectively.
Power optimisation scheme of induction motor using FLC for electric vehicle
In electric vehicles (EVs) and hybrid EVs, energy efficiency is essential where the energy storage is limited. Adding to its high stability and low cost, the induction motor efficiency improves with loss minimisation. Also, it can consume more power than the actual need to perform its working when it is operating in less than full load condition. This study proposes a control strategy based on the fuzzy logic control (FLC) for EV applications. FLC controller can improve the starting current amplitude and saves more power. Through the MATLAB/SIMULINK software package, the performance of this control was verified through simulation. As compared with the conventional proportional integral derivative controller, the simulation schemes show good, high-performance results in time-domain response and rapid rejection of system-affected disturbance. Therefore, the core losses of the induction motor are greatly reduced, and in this way improves the efficiency of the driving system. Finally, the suggested control system is validated by the experimental results obtained in the authors’ laboratory, which are in good agreement with the simulation results.
Power Flow Control of Interconnected AC-DC Microgrids in Grid-Connected Hybri...
This paper introduces a new approach for power flow control of interconnected AC-DC microgrids in grid-connected hybrid microgrids based on implementing a modified unified interphase power controller (UIPC). A typical grid-connected hybrid microgrid including one AC microgrid and one DC microgrid is considered as studied system. Instead of using the parallel-connected power converters, these microgrids are interconnected using a modified UIPC. As the first contribution of this paper, the conventional structure of UIPC, which uses three power converters in each phase, is modified so that a reduced number of power converters is implemented for power exchange control between AC-DC microgrids. The modified structure includes one power converter in each phase, named as line power converter (LPC), and a power converter which regulates the DC bus voltage, named as bus power converter (BPC) here. The AC microgrid is connected to the main grid through the LPCs which their DC buses are linked and can operate in capacitance mode (CM) or inductance mode (IM). A fuzzy logic controller is used in the control structure of the LPCs. The fuzzy inference system is optimized based on H∞ filtering method to reduce the errors in membership functions design. Through the BPC, the DC voltage of LPCs is supplied by the DC microgrid. However, since the DC microgrid voltage is provided here by a PV system, the DC link voltage of the LPCs is fluctuating. Thus, as the second contribution, to stabilize the DC link fluctuations, a new nonlinear disturbance observer based robust multiple-surface sliding mode control (NDO-MS-SMC) strategy is presented for DC side control of the BPC. The simulation results confirm the effectiveness of the proposed power flow control strategy of the improved UIPC for hybrid microgrids.
Power flow control of hybrid micro grids using modified uipc
Neuro Fuzzy Inference System (ANFIS) controlled modified Unified Inter-Phase Power Controller (UIPC). For study, a classic hybrid micro-grid connected to grid comprising of a AC micro-grid and a DC micro-grid is taken into account. These micro-grids are interconnected employing a modified UIPC, rather than using the power converters connected in parallel. As the first input of this paper is the standard structure of UIPC, which used three power converters in every phase. It was then modified such as number of power converters is used less and implemented for the control of the exchange of power between AC-DC microgrids. In every phase there is one power electronic converter in the improved structure. It is called as Line Power Converter (LPC). Also there is Bus Power Converter (BPC) to regulate the voltage of the DC bus. The Line Power Converters links the AC micro-grid to the main grid. The DC buses are also linked with them. It can be operated in Inductance Mode (IM) as well as Capacitance Mode (CM). The control structure of LPCs has an Adaptive Fuzzy Logic Controller in it. For hybrid micro-grids, the capability of the suggested power flow control strategy is confirmed by the MATLAB simulation results.
Multifunctional grid tied pv system using modified klms control
This paper deals with the modified kernel least mean square (KLMS) control strategy in double-stage, solar photovoltaic (PV) grid tied system to enhance the power quality at common coupling point (CCP). This proposed control algorithm has less oscillations, fast convergence, fast dynamic response and good steady state performance. A control strategy is used to extract the fundamental active current component of load and generates reference grid current for a DC-AC converter. The proposed modified KLMS control mitigates multiple power quality concerns such as harmonics reduction, unity power factor and load balancing. The dynamic performance of proposed system is confirmed into the MATLAB\Simulink environment. Test results on hardware implementation are presented at varying solar irradiation levels and load unbalancing. Test results are found satisfactory and total harmonic distortion (THD) of the grid currents are observed well within the IEEE-519 standard.
Modelling and voltage control of the solar wind hybrid micro-grid with optimi...
Electricity generation from the wind and solar photovoltaic (PV) systems are highly dependent upon weather conditions. Their intermittent nature leads to fluctuations in their output. Therefore, the need for rapid compensation for energy transmission and distribution systems is increasingly important. Static Synchronous Compensator (STATCOM) can be adopted for reactive power compensation and for decreasing the voltage fluctuation caused by the system and renewable energy sources. This study presents modelling of a Solar PV-Wind Hybrid Micro-grid and the increase of the stable operating limit of the system in case of the incorporation of STATCOM is examined. The major contribution of this paper is the optimization of gain parameters of four PI controllers in STATCOM control circuit based on genetic algorithms (GA) and Bacteria Foraging Algorithm (BFA) and therefore obtaining better responses and voltage stability in terms of nonlinear nature of solar-wind hybrid micro-grid. The Simulink models of the system architecture include a wind turbine model, a solar PV power system model and a STATCOM. It is certified that the voltage fluctuation at the end of the bus bar is reduced by 8% using conventional PI controller, by 10% for GA-based PI controller, and by 15% for BFA based PI controller under variable load. The results obtained by GA and BFA-based optimization of PI controllers are compared with that of the conventional controller and better results attained.
Intelligent Power Sharing of DC Isolated Microgrid Based on Fuzzy Sliding Mod...
Linear droop control can realize power sharing among generators in DC microgrid without relying on critical communication links. However, the droop relationship between output power and voltage magnitude of renewable power generate system is nonlinear with uncertainties and disturbances from renewable sources and loads in practical DC microgrid. A novel droop scheme is proposed for an isolated DC microgrid to solve the nonlinear problem. The control strategy is proposed by using the Takagi-Sugeno (T-S) fuzzy model and sliding mode algorithm. The nonlinear droop characteristics can be represented by T-S model through taking advantage of locally measured output variables. The sliding mode droop controller is designed for compensating the uncertainties and disturbances to derive accurate power sharing based on T-S fuzzy model. The proposed scheme is proved to be effective under variable operating conditions through PSIM/Matlab simulation.
Implementation of solar pv battery and diesel generator based electric vehic...
In this paper, a solar PV (Photovoltaic) array, a battery energy storage (BES), a diesel generator (DG) set and grid based EV charging station (CS) is utilized to provide the incessant charging in islanded, grid connected and DG set connected modes. The charging station is primarily designed to use the solar photovoltaic PV array and a BES to charge the electric vehicle (EV) battery. However, in case of exhausted storage battery and unavailable solar PV array generation, the charging station intelligently takes power from the grid or DG (Diesel Generator) set. However, the power from DG set is drawn in a manner that, it always operates at 80-85% loading to achieve maximum fuel efficiency under all loading conditions. Moreover, in coordination with the storage battery, the charging station regulates the generator voltage and frequency without a mechanical speed governor. It also ensures that the power drawn from the grid or the DG set is at unity power factor (UPF) even at nonlinear loading. Moreover, the PCC (Point of Common Coupling) voltage is synchronized to the grid/ generator voltage to obtain the ceaseless charging. The charging station also performs the vehicle to grid active/reactive power transfer, vehicle to home and vehicle to vehicle power transfer for increasing the operational efficiency of the charging station. The operation of the charging station is experimentally validated using the prototype developed in the laboratory.
High step up quasi-z source dc-dc converter
In this paper, a high step-up Quasi-Z Source (QZS) DC-DC converter is proposed. This converter uses a hybrid switched-capacitors switched-inductor method in order to achieve high voltage gains. The proposed converter have resolved the voltage gain limitation of the basic QZS DC-DC converter while keeping its main advantages such as continuous input current and low voltage stress on capacitors. Compared to the basic converter, the duty cycle is not limited, and the voltage stress on the diodes and switch isn’t increased. In addition to these features, the proposed converter has a flexible structure, and extra stages could be added to it in order to achieve even higher voltage gains without increasing the voltage stress on devices or limiting the duty cycle. The operation principle of the converter and related relationships and waveforms are presented in the paper. Also, a comprehensive comparison between the proposed and other QZS based DC-DC converters is provided which confirms the superiority of the proposed converter. Simulations are done in PSCAD/EMTDC in order to investigate the MPPT capability of the converter. In addition, the valid performance and practicality of the converter are studied through the results obtained from the laboratory built prototype.
Fuel cell integrated unified power quality conditioner for voltage and curren...
Electrical and electronic devices when exposed to one or more power quality problems are prone to failure. This paper aims to enhance the quality of power in three-phase four-wire distribution grid using Fuel Cell Integrated Unified Power Quality Conditioner (FCI-UPQC). The proposed FCI-UPQC has four-leg converter on the shunt side and three-leg converter on the series side. A combination of a synchronous reference frame (SRF) and Instantaneous Reactive Power (IRP) theories are utilized to generate reference signals of the FCI-UPQC. Also, this paper proposes Adaptive Neuro-Fuzzy Inference System controller to maintain DC link voltage in the FCI-UPQC. The Adaptive Neuro-Fuzzy Inference System controller is designed like a sugeno fuzzy architecture and trained offline using data from the Proportional Integral (PI) controller. The obtained results proved that the proposed FCI-UPQC compensated power quality problems such as voltage sag, swell, harmonics, neutral current, source current imbalance in three-phase four-wire distribution grid. The presence of fuel cell in this work makes more effectiveness of the proposed system by providing real power support during supply interruption on the grid side.
Distributed incremental adaptive filter controlled grid interactive residenti...
In this paper, a distributed incremental adaptive filter (DIAF) controlled utility interfaced photovoltaic (PV) - battery microgrid system is presented with power quality features. From protection aspects, grid tied solar inverters are required to shut down at loss of the utility. However, the multi-purpose PV-battery system is developed to provide energy to the critical loads, even at loss of distribution network. The bidirectional controlled converter with a battery also mitigates the intermittency of a PV array under rapid variations in the weather. The extracted maximum power is supplied to the voltage source converter (VSC), which is transferred to the nonlinear loads and the utility. The distributed incremental adaptive filter is used to control the VSC with contribution of PV power and the battery. In addition, the DIAF control provides harmonics mitigation, load balancing and power factor improvement functionalities in order to deal with system connected with nonlinear loads. A PV power feed-forward (PVFF) term is incorporated in the current control for injection of active power to the utility as well as to improve the dynamic operation of residential PV-battery microgrid. The battery energy storage (BES) reduces the fuel bills and it is also utilized to provide smoothing attributes to the microgrid. The effectiveness of PV-battery microgrid is validated experimentally developed in the laboratory.
Development of wind and solar based ac microgrid with power quality improveme...
This work proposes a microgrid (μ-grid) integrating wind and solar photovoltaic (PV) resources, along with the battery energy storage (BES) to the three phase grid feeding the nonlinear load. The μ-grid disconcerted by probabilistic nonlinear time dependent parameters and their effects are compensated by cohesive controllers used for utility grid side voltage source converter (GVSC) and machine side VSC (MVSC). The switching controls and the reconfigurability of the μ-grid are addressed on imperative aspects of improving power quality (PQ), power reliability, nonlinear load compensation and economic utilization of resources. The nonlinear load compensation and PQ enhancement are achieved by executing modified version of the adaptive filtering technique including “momentum” based least mean square (MLMS) control technique, utilized for providing the switching control signals to the GVSC. It utilizes two preceding gradient weights for obtaining updated weight thereby improving the convergence rate and overcoming the limitation of conventional control of the same family. The MVSC acquires its switching signals from conventional vector control scheme and the encoderless estimation of speed and rotor position of the synchronous generator (SG) driven by wind turbine through back electromotive force control technique. The external environmental disturbances are overcome by utilizing perturb and observe (P&O) maximum power point (MPP) for wind optimal power extraction and adaptive P&O with variable perturbation step size for solar MPP estimation. Test results are obtained from the laboratory prototype under steady state and dynamic conditions including altering wind speed, intermittent solar insolation and variable load conditions. The PQ issues are addressed and investigated successfully.
Application of Artificial Neural Networks for Shunt APF Control
Artificial Neural Network (ANN) is becoming an attractive estimation and regression technique in many control applications due to its parallel computing nature and high learning capability. There has been a lot of effort in employing the ANN in shunt active power filter (APF) control applications. Adaptive Linear Neuron (ADALINE) and feed-forward Multilayer Neural Network (MNN) are the most commonly used ANN techniques to extract fundamental and/or harmonic components present in the non-linear currents. This paper aims to provide an in-depth understanding on realizing ADALINE and feed-forward MNN based control algorithms for shunt APF. A step-by-step procedure to implement these ANN based techniques, in Matlab/ Simulink environment, is provided. Furthermore, a detailed analysis on the performance, limitation and advantages of both methods is presented in the paper. The study is supported by conducting both simulation and experimental validations.
More from Asoka Technologies (20)
Generation of Higher Number of Voltage Levels by Stacking Inverters of Lower ...
Generation of Higher Number of Voltage Levels by Stacking Inverters of Lower ...
A New Family of Step-up Hybrid Switched- Capacitor Integrated Multilevel Inve...
A New Family of Step-up Hybrid Switched- Capacitor Integrated Multilevel Inve...
A generalized multilevel inverter topology with reduction of total standing v...
A generalized multilevel inverter topology with reduction of total standing v...
Power Quality Improvement in Solar Fed Cascaded Multilevel Inverter with Outp...
Power Quality Improvement in Solar Fed Cascaded Multilevel Inverter with Outp...
Residential Community Load Management based on Optimal Design of Standalone H...
Residential Community Load Management based on Optimal Design of Standalone H...
Reliability evaluation of MPPT based interleaved boost converter for PV system
Reliability evaluation of MPPT based interleaved boost converter for PV system
Power Quality Improvement of Grid-Connected Photovoltaic Systems Using Trans-...
Power Quality Improvement of Grid-Connected Photovoltaic Systems Using Trans-...
Power optimisation scheme of induction motor using FLC for electric vehicle
Power optimisation scheme of induction motor using FLC for electric vehicle
Power Flow Control of Interconnected AC-DC Microgrids in Grid-Connected Hybri...
Power Flow Control of Interconnected AC-DC Microgrids in Grid-Connected Hybri...
Power flow control of hybrid micro grids using modified uipc
Power flow control of hybrid micro grids using modified uipc
Multifunctional grid tied pv system using modified klms control
Multifunctional grid tied pv system using modified klms control
Modelling and voltage control of the solar wind hybrid micro-grid with optimi...
Modelling and voltage control of the solar wind hybrid micro-grid with optimi...
Intelligent Power Sharing of DC Isolated Microgrid Based on Fuzzy Sliding Mod...
Intelligent Power Sharing of DC Isolated Microgrid Based on Fuzzy Sliding Mod...
Implementation of solar pv battery and diesel generator based electric vehic...
Implementation of solar pv battery and diesel generator based electric vehic...
Fuel cell integrated unified power quality conditioner for voltage and curren...
Fuel cell integrated unified power quality conditioner for voltage and curren...
Distributed incremental adaptive filter controlled grid interactive residenti...
Distributed incremental adaptive filter controlled grid interactive residenti...
Development of wind and solar based ac microgrid with power quality improveme...
Development of wind and solar based ac microgrid with power quality improveme...
Application of Artificial Neural Networks for Shunt APF Control
Application of Artificial Neural Networks for Shunt APF Control
Recently uploaded
Nuclear Power Economics and Structuring 2024
Title: Nuclear Power Economics and Structuring - 2024 Edition
Produced by: World Nuclear Association Published: April 2024
Report No. 2024/001
© 2024 World Nuclear Association.
Registered in England and Wales, company number 01215741
This report reflects the views
of industry experts but does not
necessarily represent those
of World Nuclear Association’s
individual member organizations.
Recycled Concrete Aggregate in Construction Part III
Using recycled concrete aggregates (RCA) for pavements is crucial to achieving sustainability. Implementing RCA for new pavement can minimize carbon footprint, conserve natural resources, reduce harmful emissions, and lower life cycle costs. Compared to natural aggregate (NA), RCA pavement has fewer comprehensive studies and sustainability assessments.
Final project report on grocery store management system..pdf
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
6th International Conference on Machine Learning & Applications (CMLA 2024)
6th International Conference on Machine Learning & Applications (CMLA 2024) will provide an excellent international forum for sharing knowledge and results in theory, methodology and applications of on Machine Learning & Applications.
Gen AI Study Jams _ For the GDSC Leads in India.pdf
Gen AI Study Jams _ For the GDSC Leads in India.pdf
NUMERICAL SIMULATIONS OF HEAT AND MASS TRANSFER IN CONDENSING HEAT EXCHANGERS...
Power plants release a large amount of water vapor into the
atmosphere through the stack. The flue gas can be a potential
source for obtaining much needed cooling water for a power
plant. If a power plant could recover and reuse a portion of this
moisture, it could reduce its total cooling water intake
requirement. One of the most practical way to recover water
from flue gas is to use a condensing heat exchanger. The power
plant could also recover latent heat due to condensation as well
as sensible heat due to lowering the flue gas exit temperature.
Additionally, harmful acids released from the stack can be
reduced in a condensing heat exchanger by acid condensation. reduced in a condensing heat exchanger by acid condensation.
Condensation of vapors in flue gas is a complicated
phenomenon since heat and mass transfer of water vapor and
various acids simultaneously occur in the presence of noncondensable
gases such as nitrogen and oxygen. Design of a
condenser depends on the knowledge and understanding of the
heat and mass transfer processes. A computer program for
numerical simulations of water (H2O) and sulfuric acid (H2SO4)
condensation in a flue gas condensing heat exchanger was
developed using MATLAB. Governing equations based on
mass and energy balances for the system were derived to
predict variables such as flue gas exit temperature, cooling
water outlet temperature, mole fraction and condensation rates
of water and sulfuric acid vapors. The equations were solved
using an iterative solution technique with calculations of heat
and mass transfer coefficients and physical properties.
一比一原版(UofT毕业证)多伦多大学毕业证成绩单如何办理
UofT毕业证原版定制【微信：176555708】【多伦多大学毕业证成绩单-学位证】【微信：176555708】（留信学历认证永久存档查询）采用学校原版纸张、特殊工艺完全按照原版一比一制作（包括：隐形水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠，文字图案浮雕，激光镭射，紫外荧光，温感，复印防伪）行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备，十五年致力于帮助留学生解决难题，业务范围有加拿大、英国、澳洲、韩国、美国、新加坡，新西兰等学历材料，包您满意。
◆◆◆◆◆ — — — — — — — — 【留学教育】留学归国服务中心 — — — — — -◆◆◆◆◆
【主营项目】
一.毕业证【微信：176555708】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【微信：176555708】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分→ 【关于价格问题（保证一手价格）
我们所定的价格是非常合理的，而且我们现在做得单子大多数都是代理和回头客户介绍的所以一般现在有新的单子 我给客户的都是第一手的代理价格，因为我想坦诚对待大家 不想跟大家在价格方面浪费时间
对于老客户或者被老客户介绍过来的朋友，我们都会适当给一些优惠。
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
选择实体注册公司办理，更放心，更安全！我们的承诺：可来公司面谈，可签订合同，会陪同客户一起到教育部认证窗口递交认证材料，客户在教育部官方认证查询网站查询到认证通过结果后付款，不成功不收费！
学历顾问：微信：176555708
HYDROPOWER - Hydroelectric power generation
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Immunizing Image Classifiers Against Localized Adversary Attacks
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Cosmetic shop management system project report.pdf
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Building Electrical System Design & Installation
Guide for Building Electrical System Design & Installation
在线办理(ANU毕业证书)澳洲国立大学毕业证录取通知书一模一样
学校原件一模一样【微信：741003700 】《(ANU毕业证书)澳洲国立大学毕业证》【微信：741003700 】学位证，留信认证（真实可查，永久存档）原件一模一样纸张工艺/offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原。
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
【主营项目】
一.毕业证【q微741003700】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【q/微741003700】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
RAT: Retrieval Augmented Thoughts Elicit Context-Aware Reasoning in Long-Hori...
RAT: Retrieval Augmented Thoughts Elicit Context-Aware Reasoning in Long-Horizon Generation
一比一原版(IIT毕业证)伊利诺伊理工大学毕业证成绩单专业办理
IIT毕业证原版定制【微信：176555708】【伊利诺伊理工大学毕业证成绩单-学位证】【微信：176555708】（留信学历认证永久存档查询）采用学校原版纸张、特殊工艺完全按照原版一比一制作（包括：隐形水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠，文字图案浮雕，激光镭射，紫外荧光，温感，复印防伪）行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备，十五年致力于帮助留学生解决难题，业务范围有加拿大、英国、澳洲、韩国、美国、新加坡，新西兰等学历材料，包您满意。
◆◆◆◆◆ — — — — — — — — 【留学教育】留学归国服务中心 — — — — — -◆◆◆◆◆
【主营项目】
一.毕业证【微信：176555708】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【微信：176555708】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分→ 【关于价格问题（保证一手价格）
我们所定的价格是非常合理的，而且我们现在做得单子大多数都是代理和回头客户介绍的所以一般现在有新的单子 我给客户的都是第一手的代理价格，因为我想坦诚对待大家 不想跟大家在价格方面浪费时间
对于老客户或者被老客户介绍过来的朋友，我们都会适当给一些优惠。
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
选择实体注册公司办理，更放心，更安全！我们的承诺：可来公司面谈，可签订合同，会陪同客户一起到教育部认证窗口递交认证材料，客户在教育部官方认证查询网站查询到认证通过结果后付款，不成功不收费！
学历顾问：微信：176555708
Heap Sort (SS).ppt FOR ENGINEERING GRADUATES, BCA, MCA, MTECH, BSC STUDENTS
HEAP SORT ILLUSTRATED WITH HEAPIFY, BUILD HEAP FOR DYNAMIC ARRAYS.
Heap sort is a comparison-based sorting technique based on Binary Heap data structure. It is similar to the selection sort where we first find the minimum element and place the minimum element at the beginning. Repeat the same process for the remaining elements.
Recently uploaded (20)
Recycled Concrete Aggregate in Construction Part III
Recycled Concrete Aggregate in Construction Part III
Final project report on grocery store management system..pdf
Final project report on grocery store management system..pdf
6th International Conference on Machine Learning & Applications (CMLA 2024)
6th International Conference on Machine Learning & Applications (CMLA 2024)
Gen AI Study Jams _ For the GDSC Leads in India.pdf
Gen AI Study Jams _ For the GDSC Leads in India.pdf
NUMERICAL SIMULATIONS OF HEAT AND MASS TRANSFER IN CONDENSING HEAT EXCHANGERS...
NUMERICAL SIMULATIONS OF HEAT AND MASS TRANSFER IN CONDENSING HEAT EXCHANGERS...
Fundamentals of Electric Drives and its applications.pptx
Fundamentals of Electric Drives and its applications.pptx
Immunizing Image Classifiers Against Localized Adversary Attacks
Immunizing Image Classifiers Against Localized Adversary Attacks
Cosmetic shop management system project report.pdf
Cosmetic shop management system project report.pdf
RAT: Retrieval Augmented Thoughts Elicit Context-Aware Reasoning in Long-Hori...
RAT: Retrieval Augmented Thoughts Elicit Context-Aware Reasoning in Long-Hori...
Heap Sort (SS).ppt FOR ENGINEERING GRADUATES, BCA, MCA, MTECH, BSC STUDENTS
Heap Sort (SS).ppt FOR ENGINEERING GRADUATES, BCA, MCA, MTECH, BSC STUDENTS
Planning Of Procurement o different goods and services
Planning Of Procurement o different goods and services
Critical Current Control (C3) and Modeling of a Buck Based LED Driver with Power Factor Correction
- 1. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 Critical Current Control (C3) and Modeling of a Buck Based LED Driver with Power Factor Correction ABSTRACT Buck converter has a good aptitude for LED driver application. Here a new technique introduced to control and model a buck converter in the closed loop condition using Lagrange equation. To improve the final model accuracy, parasitic elements of the converter are taken into account. The main advantage of this method is its novelty and simple implementation. Also, the converter power factor has improved under critical current control (C3) technique. Frequency response and step response of the small signal model are derived and analysed. The theoretical predictions are tested and validated by means of PSIM software. Finally, precise agreement between the proposed model and the simulation results has obtained. INDEX TERMS: 1. Power factor correction 2. LED driver 3. Buck converter 4. Small signal model. SOFTWARE: MATLAB/SIMULINK
- 2. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 CIRCUIT DIAGRAM Fig. 1. Converter overall circuitry by C3 method in the PFC mode SIMULATION RESULTS
- 3. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 Fig. 2. Converter source current and voltage along with each other Fig. 3. Reference current, input voltage and current after the bridge
- 4. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 Fig.4. Harmonic contents of the converter input current Fig.5. Output voltage at the start-up moment
- 5. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 Fig.6. Output capacitor current Fig.7. Load change effect on the converter input current CONCLUSION This paper analyses a buck based LED driver with improved power factor. Power factor correction is done using critical current control (C3) or borderline conduction mode (BCM). Also, the Lagrange differential equations are employed here as an efficient tool for switching converter modeling in the closed loop condition. The proposed modeling technique gives the designer better intuition about the circuit under study rather than traditional state space averaging (SSA) method. SSA is a tedious and fully mathematical tool for switching converters modeling. In addition, parasitic elements of the converter have taken into account so it helps to select the
- 6. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 circuit parts value correctly before manufacturing process. Dynamic behaviour of the converter is analysed in both frequency and time domain such as transfer functions and step response. A PI compensator is employed in the closed feedback loop to stabilize and modulate the reference current amplitude corresponding to the demanded power. Since this method relying on the averaging method, then the final model is reliable from 0 Hz up to half of switching frequency according to the Nyquist theorem. Finally, the simulation results confirm the proposed model exactness and indicate the rapidity of system step response under compelling conditions. REFERENCES [1] Jardini J.A. et al., Power Flow Control in the Converters Interconnecting AC-DC Meshed Systems, Przegląd Elektrotechniczny, 01(2015), 46-49. [2] Gajowik T., Rafał K., Bobrowska M., Bi-directional DC-DC converter in three-phase Dual Active Bridge Topology, Przegląd Elektrotechniczny, 05(2014), 14-20. [3] Kazmierczuk M.K., Pulse Width Modulated DC-DC Power Converters, Wiley, Ohio, 2008. [4] Ben-Yaakov S., Average simulation of PWM converters by direct implementation of behavioural relationships, IEEE Conf. , APEC, 1993, San diego, CA., 510-516. [5] Shepherd W., Zhang L., Power Converter Circuits, Marcel & Dekker Inc., New York, 2004.