This document provides instructions for configuring a network topology in Packet Tracer using 3 routers and 3 switches. It describes connecting the routers and switches with cables and configuring the IP addresses and default gateways for 6 PCs connected to the routers. It also includes directions for connecting the routers together with fiber cables and configuring RIP routing between the routers to establish communication between all devices on the 3 subnetworks.
A
PROJECT REPORT
On
CISCO CERTIFIED NETWORK ASSOCIATE
A computer network, or simply a network, is a collection of computer and other hardware components interconnected by communication channels that allow sharing of resources and information. Where at least one process in one device is able to send/receive data to/from at least one process residing in a remote device, then the two devices are said to be in a network. Simply, more than one computer interconnected through a communication medium for information interchange is called a computer network.
Inter-VLAN routing is the process of forwarding network traffic from one VLAN to another VLAN using a
router.
VLANs divide broadcast domains in a LAN environment. Whenever hosts in one VLAN need to
communicate with hosts in another VLAN, the traffic must be routed between them. This is known as
inter-VLAN routing. On Catalyst switches it is accomplished by creating Layer 3 interfaces (Switch virtual
interfaces (SVI)).
Basic idea about router. Router configuration. This is our team project. From this slide we can learn what is router configuration and application of router. We also learn the security of router.
Step by Step guide to set up a simple network in Packet TracerSorath Asnani
This document shows the detailed Steps to set up a simple network inside Packet Tracer. You will get familiarity with the software after following the Steps.
CCNA Routing Fundamentals - EIGRP, OSPF and RIPsushmil123
- Basics of Routing
- Static Routing/Dynamic Routing
- Classification of Dynamic Routing
- Administrative Distance and Metric
- Link State Routing and Distance Vector Routing
- Routing Information Protocol (RIP)
- Enhanced Interior Gateway Routing Protocol (EIGRP)
- Open Shortest Path First (OSPF)
A
PROJECT REPORT
On
CISCO CERTIFIED NETWORK ASSOCIATE
A computer network, or simply a network, is a collection of computer and other hardware components interconnected by communication channels that allow sharing of resources and information. Where at least one process in one device is able to send/receive data to/from at least one process residing in a remote device, then the two devices are said to be in a network. Simply, more than one computer interconnected through a communication medium for information interchange is called a computer network.
Inter-VLAN routing is the process of forwarding network traffic from one VLAN to another VLAN using a
router.
VLANs divide broadcast domains in a LAN environment. Whenever hosts in one VLAN need to
communicate with hosts in another VLAN, the traffic must be routed between them. This is known as
inter-VLAN routing. On Catalyst switches it is accomplished by creating Layer 3 interfaces (Switch virtual
interfaces (SVI)).
Basic idea about router. Router configuration. This is our team project. From this slide we can learn what is router configuration and application of router. We also learn the security of router.
Step by Step guide to set up a simple network in Packet TracerSorath Asnani
This document shows the detailed Steps to set up a simple network inside Packet Tracer. You will get familiarity with the software after following the Steps.
CCNA Routing Fundamentals - EIGRP, OSPF and RIPsushmil123
- Basics of Routing
- Static Routing/Dynamic Routing
- Classification of Dynamic Routing
- Administrative Distance and Metric
- Link State Routing and Distance Vector Routing
- Routing Information Protocol (RIP)
- Enhanced Interior Gateway Routing Protocol (EIGRP)
- Open Shortest Path First (OSPF)
Final Year Projects Computer Science (Information security) -2015Syed Ubaid Ali Jafri
Final Year Project Ideas for Computer Science Students, These Projects helps students to enhance their Expertise in the area of Information Security + they would be able to understand the concept of Information Security
Comment j'ai amélioré mon Kanban grâce à Bison futé - KanbanDay FR 2015Cyrille Deruel
Votre Kanban ressemble à un trafic routier ! Les tickets bougent comme des voitures sur les routes.
Je vous propose de faire comme le centre d'information routière (CIR) et d'utiliser les infos provenant de bison futé pour extraire les bonnes pratiques et les bonnes surprises afin de les intégrer dans vos projets.
Pour que votre Kanban ressemble plus à une autoroute qu'à un chemin communal !
final Year Projects, Final Year Projects in Chennai, Software Projects, Embedded Projects, Microcontrollers Projects, DSP Projects, VLSI Projects, Matlab Projects, Java Projects, .NET Projects, IEEE Projects, IEEE 2009 Projects, IEEE 2009 Projects, Software, IEEE 2009 Projects, Embedded, Software IEEE 2009 Projects, Embedded IEEE 2009 Projects, Final Year Project Titles, Final Year Project Reports, Final Year Project Review, Robotics Projects, Mechanical Projects, Electrical Projects, Power Electronics Projects, Power System Projects, Model Projects, Java Projects, J2EE Projects, Engineering Projects, Student Projects, Engineering College Projects, MCA Projects, BE Projects, BTech Projects, ME Projects, MTech Projects, Wireless Networks Projects, Network Security Projects, Networking Projects, final year projects, ieee projects, student projects, college projects, ieee projects in chennai, java projects, software ieee projects, embedded ieee projects, "ieee2009projects", "final year projects", "ieee projects", "Engineering Projects", "Final Year Projects in Chennai", "Final year Projects at Chennai", Java Projects, ASP.NET Projects, VB.NET Projects, C# Projects, Visual C++ Projects, Matlab Projects, NS2 Projects, C Projects, Microcontroller Projects, ATMEL Projects, PIC Projects, ARM Projects, DSP Projects, VLSI Projects, FPGA Projects, CPLD Projects, Power Electronics Projects, Electrical Projects, Robotics Projects, Solor Projects, MEMS Projects, J2EE Projects, J2ME Projects, AJAX Projects, Structs Projects, EJB Projects, Real Time Projects, Live Projects, Student Projects, Engineering Projects, MCA Projects, MBA Projects, College Projects, BE Projects, BTech Projects, ME Projects, MTech Projects, M.Sc Projects, Final Year Java Projects, Final Year ASP.NET Projects, Final Year VB.NET Projects, Final Year C# Projects, Final Year Visual C++ Projects, Final Year Matlab Projects, Final Year NS2 Projects, Final Year C Projects, Final Year Microcontroller Projects, Final Year ATMEL Projects, Final Year PIC Projects, Final Year ARM Projects, Final Year DSP Projects, Final Year VLSI Projects, Final Year FPGA Projects, Final Year CPLD Projects, Final Year Power Electronics Projects, Final Year Electrical Projects, Final Year Robotics Projects, Final Year Solor Projects, Final Year MEMS Projects, Final Year J2EE Projects, Final Year J2ME Projects, Final Year AJAX Projects, Final Year Structs Projects, Final Year EJB Projects, Final Year Real Time Projects, Final Year Live Projects, Final Year Student Projects, Final Year Engineering Projects, Final Year MCA Projects, Final Year MBA Projects, Final Year College Projects, Final Year BE Projects, Final Year BTech Projects, Final Year ME Projects, Final Year MTech Projects, Final Year M.Sc Projects, IEEE Java Projects, ASP.NET Projects, VB.NET Projects, C# Projects, Visual C++ Projects, Matlab Projects, NS2 Projects, C Projects, Microcontroller Projects, ATMEL Projects, PIC Projects, ARM Projects, DSP Projects, VLSI Projects, FPGA Projects, CPLD Projects, Power Electronics Projects, Electrical Projects, Robotics Projects, Solor Projects, MEMS Projects, J2EE Projects, J2ME Projects, AJAX Projects, Structs Projects, EJB Projects, Real Time Projects, Live Projects, Student Projects, Engineering Projects, MCA Projects, MBA Projects, College Projects, BE Projects, BTech Projects, ME Projects, MTech Projects, M.Sc Projects, IEEE 2009 Java Projects, IEEE 2009 ASP.NET Projects, IEEE 2009 VB.NET Projects, IEEE 2009 C# Projects, IEEE 2009 Visual C++ Projects, IEEE 2009 Matlab Projects, IEEE 2009 NS2 Projects, IEEE 2009 C Projects, IEEE 2009 Microcontroller Projects, IEEE 2009 ATMEL Projects, IEEE 2009 PIC Projects, IEEE 2009 ARM Projects, IEEE 2009 DSP Projects, IEEE 2009 VLSI Projects, IEEE 2009 FPGA Projects, IEEE 2009 CPLD Projects, IEEE 2009 Power Electronics Projects, IEEE 2009 Electrical Projects, IEEE 2009 Robotics Projects, IEEE 2009 Solor Projects, IEEE 2009 MEMS Projects, IEEE 2009 J2EE P
Présentation sur les RSE donnée à la CCI de Rennes le 11 juillet 2013 dans le cadre du cycle de conférence sur les réseaux sociaux.
Certaines images ont ét
ITNE2003 - AssignmentLearning ObjectivesUpon completion of this.docxsleeperfindley
ITNE2003 - Assignment
Learning Objectives
Upon completion of this assignment, you will be able to:
Subnet an address space given requirements.
Assign appropriate addresses to interfaces and document them in the Addressing Table.
Cable a network according to the Topology Diagram.
Erase the startup configuration and reload a router to the default state.
Configure RIPv2 routing on all routers.
Configure and propagate a static default route.
Verify RIPv2 operation.
Test and verify full connectivity.
Reflect upon and document the network implementation.
Scenario
In this lab activity, you will be given a network diagram that must be implemented in packet tracer. A combination of RIPv2 and static routing will be required so that hosts on networks that are not directly connected will be able to communicate with each other.
Topology Diagram
Task 1: Fill Addressing Table:
Step 1: Examine the network requirements.
The addressing for the network has the following requirements:
The ISP LAN will use the 203.162.108.0/24 network.
The link between the ISP router and the HQ router will use the 172.16.10.0/30 network.
The link between the BRANCH router and the HQ router will use the 172.16.10.4/30 network.
The HQ LAN will use the 192.168.1.128/25 network
The BRANCH LAN will use the 10.10.2.0/23 network.
(
Note:
Remember that the interfaces of network devices are also host IP addresses and are included in the above addressing requirements.)
Step 2: Fill the address table with appropriate IP addresses and subnet masks:
Device
Interface
IP Address
Subnet Mask
Default Gateway
BRANCH
Fa0/0
N/A
S0/0/0
N/A
HQ
Fa0/0
N/A
S0/0/0
N/A
S0/0/1
N/A
ISP
Fa0/0
N/A
S0/0/1
N/A
PC1
NIC
PC2
NIC
PC3
NIC
Task 2: Implement the Network.
Step 1: Cable a network that is similar to the one in the Topology Diagram in Packet Tracer.
You can use any current router in your lab as long as it has the required interfaces shown in the topology.
Note:
If you use 1700, 2500, or 2600 routers, the router outputs and interface descriptions will appear different.
Step 2: Perform basic administrative configuration in the BRANCH, HQ, and ISP routers
Configure the router hostname as the minimum
Task 3: Configure and Activate Serial and Ethernet Addresses.
Step 1: Configure the BRANCH, HQ, and ISP routers.
Configure the interfaces on the BRANCH, HQ, and ISP routers with the IP addresses from the Addressing Table provided under the Topology Diagram.
When you have finished, be sure to save the running configuration to the NVRAM of the router.
Step 2: Configure the Ethernet interfaces of PC1, PC2, and PC3.
Configure the Ethernet interfaces of PC1, PC2, and PC3 with the IP addresses from the Addressing Table provided under the Topology Diagram.
Task 4: Verify Connectivity to Next-Hop Device.
You should
not
have connectivity between end devices yet. However, you can test connectivity between two routers and between an end device and its default gateway.
Step 1: Verify BR.
VLAN, Trunk and 802.1q Router Configuration Objectiv.docxdickonsondorris
VLAN, Trunk and 802.1q Router Configuration
Objectives
Initial Configuration
VLAN Trunking Configuration
802.1q Router/Switch trunking
Topology
You can click the Show Lab Content button to download the lab or you can download the l ab from
[email protected] in Content.
VLAN, Trunk and 802.1q Router Configuration
Step 1: Initial Switch Configuration
Configure hostnames on the switches
Configure enable secret, console and vty (Telnet) passwords as uwstout
Configure VLANs 10, 20 and 30 on StoutSW1 and StoutSW2
Configure the ports the PCs are connected to in the proper vlans
Shutdown the fa0/4 interfaces on each switch
Configure an IEEE 802.1Q trunk between StoutSW1 and StoutSW2 using the fa0/1 interfaces
Configure the IP addresses and subnet masks on PC1a, PC1b and PC2 according to the topology
diagram
Verify your configuration before moving on to Step 2
If you need help remembering the commands for the initial configuration steps, try using ? or refer to the
previous labs.
Before moving to Step 2 verify your trunk and VLAN configuration, PC IP addresses and that the switchports
for the PCs are in the correct vlans. Use “show” commands and ipconfig to verify the initial configuration.
VLAN, Trunk and 802.1q Router Configuration
Step 2: Configure 802.1 trunk between Menomonie and StoutSW1
Data from one vlan cannot cross into another vlan without the help of a router to route the data. Currently
the PCs cannot successfully send to each other because they are on different VLANs. In this step you will
configure a trunk between the Menomonie router and the StoutSW1 switch. (This type of configuration is
referred to as “Router-on-a-Stick”) so the router can be used to route traffic between the VLANs. The
physical interface on the router that is connected to StoutSW1 is fastethernet0/1 so you will configure the
trunked sub-interfaces on the fastethernet0/1 interface. Then configure fastethernet0/8 on StoutSW1 to trunk.
Configure the Router:
Configure the hostname on the router to Menomonie:
In global configuration mode type, hostname Menomonie
Configure the first sub-interface on Menomonie to route vlan 10
In global configuration mode type, interface fastethernet0/1.10
In interface configuration mode for fa0/1.10 type, encapsulation dot1q 10
Configure the second sub-interface on Menomonie to route vlan 20
In global configuration mode type, interface fastethernet0/1.20
In interface configuration mode for fa0/1.20 type, encapsulation dot1q 20
Configure the third sub-interface on Menomonie to route vlan 30
In global configuration mode type, interface fastethernet0/1.30
In interface configuration mode for fa0/1.30 type, encapsulation dot1q 30
Now that the virtual trunked interfaces have been configured you can assign an IP address to the
interfaces. The addresses for each inter ...
CPU224XP Ethernet borad
CPU224XP Digital 14input 10output/CPU226XP Digital 24input 16output
Analog 2 channel input/1 channel output
DC24V 1A
2 channel PPI port(support Modbus)
Comes with a perpetual calendar, which can be maintained for 2 years after power failure
PPI communication interface supports 187.5K, supports Modbus protocol
Up to 7 modules can be connected
Automatic saving of power-down data
Software supports all instructions in Siemens v4.0 Step 7
LAN Design Project Packet Tracer CSCI 356 - 50 poi.docxsmile790243
LAN Design Project
Packet Tracer
CSCI 356 - 50 points
Scenario:
You have been tasked with designing your new corporate network since they found out you
have studied IP addressing, Cisco networking, and routing. Below is a screen shot of the
topology for your network:
You are responsible for the following tasks:
Design and Implement IPv4 addressing plan
Includes putting addresses on all PCs, switches, and routers
Design and Implement basic configurations for Switch 1 and Switch 2
Hostnames, Management IP address for VLAN 1, enable secret password, line console
password and Message of the Day Warning banner. Put proper default gateway address
on Switch 1 and Switch 2.
Design and Implement basic configurations on all 3 routers:
Hostnames, IP addresses on proper interfaces, enable secret password, line console
password and Message of the Day Warning banner.
Design and Implement SSH on switches
Create proper addressing on VLAN 1, usernames & passwords on Switch 1 and Switch 2
Design and Implement SSH on all 3 routers.
Create usernames & passwords on Corporate Router, ISP router and Branch office
router
Design and Implement static routing on all 3 routers so that all networks are reachable.
Create proper static routes on routers to reach all other networks.
Details on Addressing:
You have been given the following major IP address: _________________________________
NOTE: You will each have your own different major IP address that you need to subnet. In
other words, everyone will have a slightly different problem!
You need to subnet that into 4 separate networks.
Network 1 subnet - Corporate LAN
Network 2 subnet - Connection between Corp Router G0/0 to ISP G0/0
Network 3 subnet - Connection between ISP Router G0/1 to Branch office Router G0/1
Network 4 subnet - Branch Office LAN
Put proper addressing on Corporate Router interfaces G0/0 and G0/1
Put proper addressing on ISP router G0/0 and G0/1
Put proper addressing on Branch Office Router G0/0 and G0/1
Turn on all interfaces on all 3 routers by issuing the no shutdown command for each interface
Put VLAN 1 ip address on Switch 1 - Should be address in Network 1 Corporate LAN subnet
Put VLAN 1 ip address on Switch 2 - should be address in Network 4 Branch office LAN
subnet.
Put proper addressing, subnet mask and default gateway on PCs and Server in Corporate LAN.
They should use addresses in Network 1 subnet.
Put proper addressing, subnet mask and default gateway on PCs in Branch Office LAN. They
should use addresses from Network 4 subnet.
Configure static routing on all 3 routers.
Corporate router will need a route to Branch office LAN and connection between ISP and
Branch router.
ISP router will need a route to Corporate LAN and Branch office LAN
Branch router will need a route to Corporate LAN and connection between ISP and Corp router.
TESTING & VALIDATI ...
How to Create Map Views in the Odoo 17 ERPCeline George
The map views are useful for providing a geographical representation of data. They allow users to visualize and analyze the data in a more intuitive manner.
Palestine last event orientationfvgnh .pptxRaedMohamed3
An EFL lesson about the current events in Palestine. It is intended to be for intermediate students who wish to increase their listening skills through a short lesson in power point.
The Indian economy is classified into different sectors to simplify the analysis and understanding of economic activities. For Class 10, it's essential to grasp the sectors of the Indian economy, understand their characteristics, and recognize their importance. This guide will provide detailed notes on the Sectors of the Indian Economy Class 10, using specific long-tail keywords to enhance comprehension.
For more information, visit-www.vavaclasses.com
Students, digital devices and success - Andreas Schleicher - 27 May 2024..pptxEduSkills OECD
Andreas Schleicher presents at the OECD webinar ‘Digital devices in schools: detrimental distraction or secret to success?’ on 27 May 2024. The presentation was based on findings from PISA 2022 results and the webinar helped launch the PISA in Focus ‘Managing screen time: How to protect and equip students against distraction’ https://www.oecd-ilibrary.org/education/managing-screen-time_7c225af4-en and the OECD Education Policy Perspective ‘Students, digital devices and success’ can be found here - https://oe.cd/il/5yV
The Art Pastor's Guide to Sabbath | Steve ThomasonSteve Thomason
What is the purpose of the Sabbath Law in the Torah. It is interesting to compare how the context of the law shifts from Exodus to Deuteronomy. Who gets to rest, and why?
Read| The latest issue of The Challenger is here! We are thrilled to announce that our school paper has qualified for the NATIONAL SCHOOLS PRESS CONFERENCE (NSPC) 2024. Thank you for your unwavering support and trust. Dive into the stories that made us stand out!
How to Split Bills in the Odoo 17 POS ModuleCeline George
Bills have a main role in point of sale procedure. It will help to track sales, handling payments and giving receipts to customers. Bill splitting also has an important role in POS. For example, If some friends come together for dinner and if they want to divide the bill then it is possible by POS bill splitting. This slide will show how to split bills in odoo 17 POS.
Ethnobotany and Ethnopharmacology:
Ethnobotany in herbal drug evaluation,
Impact of Ethnobotany in traditional medicine,
New development in herbals,
Bio-prospecting tools for drug discovery,
Role of Ethnopharmacology in drug evaluation,
Reverse Pharmacology.
Model Attribute Check Company Auto PropertyCeline George
In Odoo, the multi-company feature allows you to manage multiple companies within a single Odoo database instance. Each company can have its own configurations while still sharing common resources such as products, customers, and suppliers.
The French Revolution, which began in 1789, was a period of radical social and political upheaval in France. It marked the decline of absolute monarchies, the rise of secular and democratic republics, and the eventual rise of Napoleon Bonaparte. This revolutionary period is crucial in understanding the transition from feudalism to modernity in Europe.
For more information, visit-www.vavaclasses.com
We all have good and bad thoughts from time to time and situation to situation. We are bombarded daily with spiraling thoughts(both negative and positive) creating all-consuming feel , making us difficult to manage with associated suffering. Good thoughts are like our Mob Signal (Positive thought) amidst noise(negative thought) in the atmosphere. Negative thoughts like noise outweigh positive thoughts. These thoughts often create unwanted confusion, trouble, stress and frustration in our mind as well as chaos in our physical world. Negative thoughts are also known as “distorted thinking”.