ESwitching Final Exam - CCNA Exploration LAN Switching and Wireless (Version 4.0)                                         ...
3Refer to the exhibit. Switch SW2 was tested in a lab environment and then inserted into a production network withoutreloa...
Refer to the exhibit. R1 is configured for traditional inter-VLAN routing. R1 can ping computer 3 but cannot ping computer...
6Which three actions are performed during the boot sequence of a Cisco switch? (Choose three.)    The boot loader uses the...
9Refer to the exhibit. Router RA receives a packet with a source address of 192.168.1.65 and a destination address of192.1...
10Refer to the exhibit. The devices in the network are operational and configured as indicated in the exhibit. However, ho...
11Refer to the exhibit. Which three options correctly describe the router configuration that is shown? (Choose three.)    ...
Refer to the exhibit. The configuration steps that are listed in the exhibit have been entered in switch S1 via the consol...
Refer to the exhibit. Switch SW2 has been newly purchased and added to the network. What configuration should be appliedto...
21Refer to the exhibit. What does "FORWARDING" mean in the command output shown?     The switch is sending and receiving d...
23Which benefit is gained by designing a network with a small network diameter?     lower latency     improved security   ...
Refer to the exhibit. An administrator documented the output of a CAM table from an Ethernet switch as shown. Whataction w...
28Refer to the exhibit. If switch SW1 is configured with the four VLANs as shown in the exhibit, how many physicalinterfac...
The VLAN1 interface has not be enabled with the no shutdown command.30When implementing a router-on-a-stick, what must be ...
32Refer to the exhibit. What would happen if the network administrator moved the network cable of Host A from interfaceFa0...
Refer to the exhibit. What will allow a host that is connected to switch X in VLAN 10 to communicate with a host that isco...
36Refer to the exhibit. A new host needs to be connected to VLAN 20. Which IP address should be assigned to this new host?...
The router supports encryption and authentication.     The router supports both wired and wireless connections.     The ro...
Refer to the exhibit. Router R1 is properly configured for router on a stick inter-VLAN routing, but PC1 is unable to ping...
Refer to the exhibit. What are two reasons for the Fa0/24 port being placed in the blocking state? (Choose two.)     This ...
The switch ports are on different VLANs.     The switch IP address is on the wrong subnet.     The hosts are configured on...
Refer to the exhibit. Users A and B are reporting intermittent connectivity problems. Pre-installation surveys showed stro...
48Which type of frame contains information that is used in the election of the spanning tree root bridge?     BID     LSA ...
Refer to the exhibit. Switches S2 and S3 are properly connected using an ethernet cable. A network administrator hasconfig...
Upcoming SlideShare
Loading in …5
×

3 2

670 views

Published on

0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
670
On SlideShare
0
From Embeds
0
Number of Embeds
4
Actions
Shares
0
Downloads
11
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

3 2

  1. 1. ESwitching Final Exam - CCNA Exploration LAN Switching and Wireless (Version 4.0) By: Owey1Why is it important that the network administrator consider the spanning-tree network diameter when choosing the rootbridge? The network diameter limitation is 9. BPDUs may be discarded because of expiring timers. The cabling distance between the switches is 100 meters. The network diameter must be set to the number of meters of the cable between the root bridge and its farthest connected switch.2Refer to the exhibit. A network administrator configures HyperTerminal with the parameters shown but is unable to connectto a switch via the console port. The administrator is using a tested rollover cable attached to the only COM port on thecomputer, and the connections have been verified. What is the likely problem? The cable is connected to the wrong port. The wrong connection speed is selected. The cable is the wrong type. The flow control setting is not correct. The stop bits should be set to zero.
  2. 2. 3Refer to the exhibit. Switch SW2 was tested in a lab environment and then inserted into a production network withoutreloading its configuration. After the trunk link between SW1 and SW2 was brought up, all users lost connectivity to thenetwork. What could be the source of the problem? All the VLANs were pruned from the trunk port between SW1 and SW2. SW1 and SW2 cannot be both set as VTP servers in the same VTP domain. VTP configuration revision number of SW2 was higher than the configuration revision number of SW1. The additional VLANs from SW2 created more VLANs than the VLAN database of SW1 could contain.4
  3. 3. Refer to the exhibit. R1 is configured for traditional inter-VLAN routing. R1 can ping computer 3 but cannot ping computer 1.What is a possible cause for this failure? S1 port Fa0/11 is in the wrong VLAN. R1 does not have an active routing protocol. The IP address of computer 1 is in the wrong logical network. Router interface Fa0/0 has the wrong trunk encapsulation type configured.5Refer to the exhibit. The hosts connected to switch SW1 are not able to communicate with the hosts in the same VLANsconnected to switch SW2. What should be done to fix the problem? Configure VLANs with different VLAN IDs on switch SW2. Reconfigure the trunk port on switch SW2 with static trunk configuration. Introduce a Layer 3 device or a switch with Layer 3 capability in the topology. Apply IP addresses that are in the same subnet to the interfaces used to connect SW1 and SW2.
  4. 4. 6Which three actions are performed during the boot sequence of a Cisco switch? (Choose three.) The boot loader uses the self-contained switch operating system to boot the switch. The boot loader retrieves diagnostics routines via TFTP. The boot loader performs POST. The boot loader is loaded from RAM. The boot loader initializes the flash file system that is used to boot the system. The boot loader loads the default operating system if the flash-based operating system is corrupt or missing.7An administrator is viewing the running configuration for a switch on the network. The enable password is displayed in plaintext but the enable secret password has been encrypted. What level of access can be gained using the enable password? no access to privileged mode full access to privileged mode full access to privileged mode on Telnet connections full access to privileged mode if the enable password and the enable secret password are the same8Refer to the exhibit. A network administrator has segmented the network into two VLANs. The connected hosts can onlyaccess resources in their own VLAN. What is the most scalable and cost effective solution to allow inter-VLANcommunication in this network? Replace S1 with a router that has one FastEthernet interface for each PC. Add a second switch and divide the PCs so that each VLAN is connected to its own switch. Configure a router with two subinterfaces on one of its FastEthernet ports and connect it to S1 using a trunk link. Connect a router to a port on S1 and assign the IP address of VLAN1 to the connecting router interface.
  5. 5. 9Refer to the exhibit. Router RA receives a packet with a source address of 192.168.1.65 and a destination address of192.168.1.85. What will the router do with this packet? The router will ignore the packet. The router will forward the packet out interface FastEthernet 0/1.2 and interface FastEthernet 0/1.3. The router will forward the packet out interface FastEthernet 0/1.1. The router will forward the packet out interface FastEthernet 0/1.2. The router will forward the packet out interface FastEthernet 0/1.3.
  6. 6. 10Refer to the exhibit. The devices in the network are operational and configured as indicated in the exhibit. However, hostsA and D cannot ping each other. What is the most likely cause of this problem? The link between the switches is up but not trunked. The Fa0/11 interface of Switch1 is not configured as a trunk. Hosts A and D are configured with IP addresses from different subnets. VLAN 20 and VLAN 30 are not allowed on the trunk between the switches.
  7. 7. 11Refer to the exhibit. Which three options correctly describe the router configuration that is shown? (Choose three.) An IEEE standard trunking protocol is in use. Interface Fa0/1 has been configured with subinterfaces. The shutdown command has been applied to interface Fa0/1. Interface Fa0/1.3 is mapped to the default management VLAN. The configuration is appropriate for a router-on-a-stick network design. An IP address should be applied to interface Fa0/1 for routing to occur.12A network administrator needs to save the configuration file currently in RAM to NVRAM before rebooting the switch.Which command should the administrator issue? Switch1# copy startup-config flash:filename Switch1# copy running-config startup-config Switch1# copy startup-config running-config Switch1# copy flash:config.txt running-config13
  8. 8. Refer to the exhibit. The configuration steps that are listed in the exhibit have been entered in switch S1 via the console.Subsequent attempts to telnet to the switch are not successful. What is causing the problem? The switch must be configured with SSH version 1. The transport input command must specify Telnet access. The RSA keys must be returned to zero before SSH will permit Telnet access. The ip domain-name command must also be entered in line configuration mode for the vty lines.14Which parameter is associated with wireless authentication? shared key SSID ad hoc channel15A wireless LAN access point will convert traffic between which two frame encapsulation types? 802.1 and 802.11 802.3 and 802.11 802.3 and 802.16 802.5 and 802.1616
  9. 9. Refer to the exhibit. Switch SW2 has been newly purchased and added to the network. What configuration should be appliedto SW2 so that it participates in the same VTP domain as switch SW1, receives VLAN information from SW1, andsynchronizes VLAN information? Disable VTP pruning on SW2. Configure SW2 in VTP transparent mode. Configure SW2 with the VTP domain password. Configure SW2 as a VTP server with a higher revision number.17What is the correct order in which the STP components are chosen? designated ports, nondesignated ports, root bridge, root ports nondesignated ports, designated ports, root ports, root bridge root bridge, root ports, designated ports, nondesignated ports root ports, root bridge, nondesignated ports, designated ports18What are three features of router-on-a-stick, inter-VLAN routing? (Choose three.) requires the use of VTP requires the use of subinterfaces reduces the number of broadcast domains affects performance when many VLANs are used requires an access link between the router and at least one switch is more cost effective than other approaches to inter-VLAN routing dictates that at least two switch ports be used between the router and the switch19While configuring a new switch, a network administrator configures the switch as an HTTP server. What benefits does thisconfiguration provide? This allows the switch to host web pages for the network. This allows remote VPN connections to the switch over the Internet. This is required if a web server or web farm is attached to the switch. This allows web-based configuration tools to be used with the switch.20What will be the effect of the command S1# copy system:running-config tftp://172.16.2.155/tokyo-config? The IOS will be copied to the TFTP server. The configuration file named tokyo-config will overwrite the startup configuration file on S1. The running configuration file on S1 will be saved via TFTP to a file named tokyo-config. The contents of NVRAM on S1 will become the startup configuration file on the tokyo switch.
  10. 10. 21Refer to the exhibit. What does "FORWARDING" mean in the command output shown? The switch is sending and receiving data frames. The switch is receiving BPDUs, but not sending data frames. The switch is participating in an election process by forwarding the BPDUs it receives. The switch is receiving BPDUs and populating the MAC address table, but not sending data.22Refer to the exhibit. What does STATIC indicate in the output that is shown? This entry will be removed and refreshed every 300 seconds to keep it in the table. The switch learned this MAC address from the source address in a frame received on Fa0/15. The switch will only allow a device with a MAC address of 0000.c123.5432 to connect to port Fa0/15. When processing a frame, the switch does not have to perform a lookup to determine the final destination port. The switch is configured to forward traffic destined for MAC address 0000.c123.5432 will be forwarded to Fa0/15.
  11. 11. 23Which benefit is gained by designing a network with a small network diameter? lower latency improved security increased redundancy higher interface bandwidth24Refer to the exhibit. Which Spanning Tree Protocol version is in effect? Per VLAN Spanning Tree (PVST) Per VLAN Spanning Tree + (PVST+) Common Spanning Tree (CST) Rapid Spanning Tree Protocol (RSTP) Multiple Spanning Tree Protocol (MSTP)25
  12. 12. Refer to the exhibit. An administrator documented the output of a CAM table from an Ethernet switch as shown. Whataction will the switch take when it receives the frame shown at the bottom of the exhibit? discard the frame forward the frame out port 2 forward the frame out port 3 forward the frame out all ports forward the frame out all ports except port 3 add station 00-00-3D-1F-11-05 to port 2 in the forwarding table26Refer to the exhibit. The switches in the exhibit have VTP pruning enabled. Which VLAN(s) will be allowed on the trunk toSW2 by SW4? VLAN 20 only VLAN 10 and VLAN 30 VLAN 10, VLAN 20, and VLAN 30 VLAN 1, VLAN 20 and VLANs 1002 through 100527What are two benefits of the IEEE 802.11n standard over the IEEE 802.11G? (Choose two.) requires less equipment provides improved range permits increased data rates has a single-input and a single-output needs no hardware upgrade for compatibility
  13. 13. 28Refer to the exhibit. If switch SW1 is configured with the four VLANs as shown in the exhibit, how many physicalinterfaces are needed on router R1 to configure inter-VLAN routing using subinterfaces? zero one two four29Refer to the exhibit. After entering the commands in the exhibit, the administrator receives a "password required, but noneset" message when attempting to connect to S1. What is the problem? The enable secret password was not set. S1 does not have login configured on the vty lines. S1 does not have a password configured for the vty lines. The crypto key is not properly configured to generate passwords.
  14. 14. The VLAN1 interface has not be enabled with the no shutdown command.30When implementing a router-on-a-stick, what must be configured on the router to ensure connectivity between differentVLANs? subinterfaces routing protocol switched virtual circuits dynamic trunking protocol31Refer to the exhibit. Hosts A and B attempt to transmit a frame at the same time and a collision occurs. When will host D beable to transmit? immediately after sending its jam signal after host A and host B have completed transmission after the jam signal clears and its backoff delay expires
  15. 15. 32Refer to the exhibit. What would happen if the network administrator moved the network cable of Host A from interfaceFa0/1 to Fa0/3 on switch SW1? Host A remains a member of VLAN 10, because the router is routing traffic between VLANs. Host A is no longer a member of VLAN 10, because port Fa0/3 has been manually assigned to VLAN 30. Host A remains a member of VLAN 10, because the switch provides dynamic VLAN assignment for the port. Host A maintains connectivity to all members of VLAN 10, because it is connected to the same physical network. Host A is no longer a member of VLAN 10, but because port Fa0/3 was unused, it is now a member of VLAN 1.33
  16. 16. Refer to the exhibit. What will allow a host that is connected to switch X in VLAN 10 to communicate with a host that isconnected to switch Y in VLAN 10? QoS routing trunking VPN VoIP subinterfaces34Refer to the exhibit. Computer A sends a broadcast message. Which devices will see the broadcast? computer B computer B and Router1 computer C and Router1 computer B, computer D, computer E and Router1 computer B, computer C, computer D, computer E and Router1 computer A, computer B, computer C, computer D, computer E and Router135Which value determines if a switch becomes the central point of reference in the spanning tree topology? lowest bridge ID highest revision number lowest numeric IP address highest numeric MAC address
  17. 17. 36Refer to the exhibit. A new host needs to be connected to VLAN 20. Which IP address should be assigned to this new host? 172.16.10.68 /27 172.16.10.99 /28 172.16.10.110 /27 172.16.30.96 /27 172.16.30.120 /28 172.16.30.146 /2737Refer to the graphic. In the Wireless menu option of a Linksys integrated router, what does the Network Mode optionMixed mean?
  18. 18. The router supports encryption and authentication. The router supports both wired and wireless connections. The router supports 802.11b, 802.11g, and 802.11n devices. The router supports connectivity through infrared and radio frequencies.38Refer to the exhibit. What will be the result of the commands that are shown in the exhibit? Only clients on VLAN 2 will be able to use DHCP for addressing. DHCP server responses will only be permitted on interface Fa0/2. Only 100 clients are permitted to request DHCP addresses on VLAN 2. Client requests for DHCP addresses will be filtered out if the requests are not received on interface Fa0/2.39Which method establishes an administrative connection for configuring the Linksys WRT300N wireless access point? Associate with the access point and then open a HyperTerminal session with the access point. Physically connect to the access point and then reboot the computer to launch the configuration software. From a computer in the same IP subnet as the access point, enter the default IP address of the access point in a web browser. Modify the TCP/IP properties of the computer connected to the access point so that it exists on the same network, and then reboot your computer to establish a connection.40Which statement is true about open authentication when it is enabled on an access point? requires no authentication uses a 64-bit encryption algorithm requires the use of an authentication server requires a mutually agreed upon password41
  19. 19. Refer to the exhibit. Router R1 is properly configured for router on a stick inter-VLAN routing, but PC1 is unable to pingPC2. What needs to be done to resolve the problem? Rename VLAN1. Connect one more port of S1 to R1. Configure the Fa0/1 port of S1 as a trunk port. Move the Fa0/0 interface of R1 to another VLAN.42
  20. 20. Refer to the exhibit. What are two reasons for the Fa0/24 port being placed in the blocking state? (Choose two.) This switch is not the root bridge. The Fa0/24 port is administratively down. STP has detected links that create a loop. There is a change in the VTP configuration. The Fa0/24 port is overloaded with too much traffic for its configured bandwidth.43How does Spanning Tree Protocol aid network architecture? allows for redundant links by eliminating loops provides greater scalability by eliminating collisions reduces switch processor load by reducing broadcast traffic on trunk links reduces administrative overhead by sharing VLAN databases between switches across the network44Refer to the exhibit. What three statements describe why Host1 and Host2 are unable to communicate? (Choose three.)
  21. 21. The switch ports are on different VLANs. The switch IP address is on the wrong subnet. The hosts are configured on different logical networks. A router is required to forward traffic between Host1 and Host2. The VLAN port assignments must be contiguous for each VLAN. The host default gateway addresses must be on the same logical network.45Which device or devices should have the Spanning Tree Protocol enabled to prevent host traffic from creating a broadcaststorm? Core_S1 Access_S2 and Access_S3 Core_S1, Access_S2, and Access_S3 Core_S1, Access_S2, Access_S3, and R146
  22. 22. Refer to the exhibit. Users A and B are reporting intermittent connectivity problems. Pre-installation surveys showed strongsignal strength from the AP locations to the client locations. Outside electrical interference has been eliminated. What willfix the problem? Relocate the APs closer to each other. Increase the distance between the clients. Change the channel on AP-B to 6 or 11. Place AP-A and AP-B on the same wireless channel.47Refer to the exhibit. Hosts PC_A and PC_B send traffic simultaneously, and the frames from the transmitting stationscollide. What is the last device to receive the collision? hub HB1 switch SW1 router R1 switch SW2 router R2 switch SW4
  23. 23. 48Which type of frame contains information that is used in the election of the spanning tree root bridge? BID LSA LSU BPDU49Refer to the exhibit. All hosts are in listen mode. Host 1 and Host 4 both transmit data at the same time. How do the hostsrespond on the network? (Choose two.) After the end of the jam signal, a backoff algorithm is invoked. Hosts 1 and 4 are operating full duplex so no collision will exist. The hub will block the port connected to Host 4 to prevent a collision. Hosts 1 and 4 are assigned shorter backoff values to provide them priority to access the media. If a host has data to transmit after the backoff period of that host, the host checks to determine if the line is idle before transmitting.50
  24. 24. Refer to the exhibit. Switches S2 and S3 are properly connected using an ethernet cable. A network administrator hasconfigured both switches with VTP, but S3 is unable to propagate VLANs to S2. What could be the reason for this? The VTP configuration revision is different on both switches. The VTP domains are different on both switches. VTP pruning is disabled. VTP v2 is disabled.51Which parameter is used to uniquely identify one wireless network from another? SSID OFDM WEP DSSS52In which mode is a VTP switch operating if it does not allow for the creation of local VLANs but it does accept VLANupdates from other switches in the same domain? client root server transparent

×