This presentation provides an explanation of Active & Passive Circuit Element: Independent & dependent voltage & current sources, R, L, C, and Their mathematical modes, Voltage current power relations, Series and Parallel circuits, Kirchhoff's Laws. It also provides an information about
Classification of elements with numerical examples.
Presentation about chapter 1 of electrical circuit analysis. standard prefixes. basic terminology power,current,voltage,resistance.How power is absorbed by the circuit and its calculation with passive sign convention.
Inverter is a device which convert a DC input supply voltage into symmetric AC voltage of desired magnitude and frequency at the output side. It is also know as DC-AC converter.
Ideal and practical inverter have sinusoidal and no-sinusoidal waveforms at output respectively.
If the input dc is a voltage source, the inverter is called a Voltage Source Inverter (VSI). One can similarly think of a Current Source Inverter (CSI), where the input to the circuit is a current source. The VSI circuit has direct control over ‘output (ac) voltage’ whereas the CSI directly controls ‘output (ac) current.
Inverter is a device which convert a DC input supply voltage into symmetric AC voltage of desired magnitude and frequency at the output side. It is also know as DC-AC converter.
Ideal and practical inverter have sinusoidal and no-sinusoidal waveforms at output respectively.
If the input dc is a voltage source, the inverter is called a Voltage Source Inverter (VSI). One can similarly think of a Current Source Inverter (CSI), where the input to the circuit is a current source. The VSI circuit has direct control over ‘output (ac) voltage’ whereas the CSI directly controls ‘output (ac) current.
This presentation provides an explanation of Active & Passive Circuit Element: Independent & dependent voltage & current sources, R, L, C, and Their mathematical modes, Voltage current power relations, Series and Parallel circuits, Kirchhoff's Laws. It also provides an information about
Classification of elements with numerical examples.
Presentation about chapter 1 of electrical circuit analysis. standard prefixes. basic terminology power,current,voltage,resistance.How power is absorbed by the circuit and its calculation with passive sign convention.
Inverter is a device which convert a DC input supply voltage into symmetric AC voltage of desired magnitude and frequency at the output side. It is also know as DC-AC converter.
Ideal and practical inverter have sinusoidal and no-sinusoidal waveforms at output respectively.
If the input dc is a voltage source, the inverter is called a Voltage Source Inverter (VSI). One can similarly think of a Current Source Inverter (CSI), where the input to the circuit is a current source. The VSI circuit has direct control over ‘output (ac) voltage’ whereas the CSI directly controls ‘output (ac) current.
Inverter is a device which convert a DC input supply voltage into symmetric AC voltage of desired magnitude and frequency at the output side. It is also know as DC-AC converter.
Ideal and practical inverter have sinusoidal and no-sinusoidal waveforms at output respectively.
If the input dc is a voltage source, the inverter is called a Voltage Source Inverter (VSI). One can similarly think of a Current Source Inverter (CSI), where the input to the circuit is a current source. The VSI circuit has direct control over ‘output (ac) voltage’ whereas the CSI directly controls ‘output (ac) current.
Introduction to operational Amplifier. For A2 level physics (CIE). Discusses characteristics of op amp, inverting and non inverting amplifier, and voltage follower, and transfer characetristics, virtual earth , etc
Synthesis of unsymmetrical phasors from their symmetrical componentsAbhishek Choksi
Power systems are large and complex three phase system
In normal operating conditions , electrical power system operate in balanced condition.
But sometimes certain situation occurs like fault or short circuit which make the system to be unstable.
Single phase equivalent system method of analysis cannot be applied to such system.
Lecture Outline
Introduction to subject
Application Areas
Power Electronic Devices
Power Converters
What is power electronics?
1) Definition
Power Electronics: is the electronics applied to conversion and control of electric power.
Prerequisites
Power electronics incorporates concepts from the fields of
Analog circuits
Electronic devices
Control systems
Power systems
Magnetics
Electric machines
Numerical simulation
Scope
It is not possible to build practical computers, cell phones, personal data devices, cars, airplanes, industrial processes, and other everyday products without power electronics.
Alternative energy systems such as wind generators, solar power, fuel cells, and others require power electronics to function.
Technology advances such as electric and hybrid vehicles, laptop computers, microwave ovens, flat-panel displays, LED lighting, and hundreds of other innovations were not possible until advances in power electronics enabled their implementation.
Although no one can predict the future, it is certain that power electronics will be at the heart of fundamental energy innovations.
Applications: Electric VehicleTesla Model S
Functions of the power electronics:
1. Convert the DC battery voltage to the variable AC required to drive the AC motor
240 V battery
Variable-frequency, variable-voltage AC drives the motor
AC motor propels the rear axle
Up to 330 kW (acceleration)
Up to 60 kW regenerative braking
2. Control charging of the battery
Interface to 240 V 60 Hz 1φ 100 A circuit in garage.
Control AC current waveform to be sinusoidal, unity power factor.
Control charging of battery to maximize life.
Applications: Hybrid VehiclesPrius
Power Electronics Module:
Convert the DC battery voltage to the variable AC required to drive the AC motor.
Includes dc-dc boost converter and dc-3φ ac inverter
Control system can operate in all-electric mode or in hybrid gas+electric mode
Partial-power electronics
Novel Single Phase Full Bridge Inverter Formed by Floating CapacitorsIAES-IJPEDS
In this paper, a new single-phase bridge inverter is described which can
generate a more steps of voltage levels with reduced number of switches,
gate driver circuits and diodes as compare to normal multilevel inverter.
Another feature of this inverter is its ability to prodeuce the voltages from a
single dc-link power supply which enables back-to-back operation of
converter. The proposed method with more number of levels can improve
power quality, lower switching losses and produce high quality voltage
waveforms. Moreover at all load power factors the proposed method can be
operated.The research of the model is done by means of computer simulation
with the software MATLAB/SIMULINK. This topology has very low
common mode voltage variation and dv/dt stress. Also this inverter is help
full for reactive power compensation.
Introduction to operational Amplifier. For A2 level physics (CIE). Discusses characteristics of op amp, inverting and non inverting amplifier, and voltage follower, and transfer characetristics, virtual earth , etc
Synthesis of unsymmetrical phasors from their symmetrical componentsAbhishek Choksi
Power systems are large and complex three phase system
In normal operating conditions , electrical power system operate in balanced condition.
But sometimes certain situation occurs like fault or short circuit which make the system to be unstable.
Single phase equivalent system method of analysis cannot be applied to such system.
Lecture Outline
Introduction to subject
Application Areas
Power Electronic Devices
Power Converters
What is power electronics?
1) Definition
Power Electronics: is the electronics applied to conversion and control of electric power.
Prerequisites
Power electronics incorporates concepts from the fields of
Analog circuits
Electronic devices
Control systems
Power systems
Magnetics
Electric machines
Numerical simulation
Scope
It is not possible to build practical computers, cell phones, personal data devices, cars, airplanes, industrial processes, and other everyday products without power electronics.
Alternative energy systems such as wind generators, solar power, fuel cells, and others require power electronics to function.
Technology advances such as electric and hybrid vehicles, laptop computers, microwave ovens, flat-panel displays, LED lighting, and hundreds of other innovations were not possible until advances in power electronics enabled their implementation.
Although no one can predict the future, it is certain that power electronics will be at the heart of fundamental energy innovations.
Applications: Electric VehicleTesla Model S
Functions of the power electronics:
1. Convert the DC battery voltage to the variable AC required to drive the AC motor
240 V battery
Variable-frequency, variable-voltage AC drives the motor
AC motor propels the rear axle
Up to 330 kW (acceleration)
Up to 60 kW regenerative braking
2. Control charging of the battery
Interface to 240 V 60 Hz 1φ 100 A circuit in garage.
Control AC current waveform to be sinusoidal, unity power factor.
Control charging of battery to maximize life.
Applications: Hybrid VehiclesPrius
Power Electronics Module:
Convert the DC battery voltage to the variable AC required to drive the AC motor.
Includes dc-dc boost converter and dc-3φ ac inverter
Control system can operate in all-electric mode or in hybrid gas+electric mode
Partial-power electronics
Novel Single Phase Full Bridge Inverter Formed by Floating CapacitorsIAES-IJPEDS
In this paper, a new single-phase bridge inverter is described which can
generate a more steps of voltage levels with reduced number of switches,
gate driver circuits and diodes as compare to normal multilevel inverter.
Another feature of this inverter is its ability to prodeuce the voltages from a
single dc-link power supply which enables back-to-back operation of
converter. The proposed method with more number of levels can improve
power quality, lower switching losses and produce high quality voltage
waveforms. Moreover at all load power factors the proposed method can be
operated.The research of the model is done by means of computer simulation
with the software MATLAB/SIMULINK. This topology has very low
common mode voltage variation and dv/dt stress. Also this inverter is help
full for reactive power compensation.
Electrical current, voltage, resistance, capacitance, and inductance are a few of the basic elements of electronics and radio. Apart from current, voltage, resistance, capacitance, and inductance, there are many other interesting elements to electronic technology. ... Use Electronics Notes to learn electronics online.
This paper proposes the use of Embedded EZ-source
inverter system (EZSI) as a single stage power conversion
concept for adjustable speed drives (ASD) in photovoltaic
applications. Open loop and closed loop control strategy of
EZSI system are proposed. EZSI produces the same voltage
gain as Z-source inverter (ZSI) but due to the DC sources
embedded within the X- shaped impedance network, it has
the added advantage of inherent source filtering capability
and also reduced capacitor sizing. This is attained without
any extra passive filters. By controlling the shoot-through
duty ratio and modulation index, EZSI system can produce
any desired AC output voltage even greater than DC rail
voltage and it also provides ride-through capability under
voltage sag. These advantages are more significant for
adjustable speed drive (ASD) applications in order to regulate
the speed. The operational analysis, control strategy and
simulation results exemplify that an EZSI is the most
promising technique for renewable energy applications in
order to reduce the overall system complexity and thereby
improving the inverter efficiency.
Wind power stations, many located in remote areas; so they are characterized by weak grids and are often submitted to power system disturbance like faults. In this paper, the behaviour of a wind energy conversion system that uses the control of the rotor side converter (RSC) by three different methods under faulty conditions is presented. The behaviour of these systems during a grid failure is an important issue. DFIG is analysed and simulated under differing faulty conditions in the environment of MATLAB/SIMULINK. Simulation results show that the proposed method has proper operation during fault conditions.
Solar photovoltaic cells materials, current ,voltage ,characteristics are explained in this ppt how they work their active region their saturation region their cut-off region
A New Configuration of a High Output Voltage 2.45 GHz Rectifier for Wireless ...TELKOMNIKA JOURNAL
This work deals with the design, simulation, fabrication and experimentation of a novel 2.45 GHz rectifier for wireless power transmission applications. We have designed a voltage multiplier topology rectifier including 5 Schottky diodes known by their low threshold. This rectifier could perform a wireless power supply for many cases where the use of batteries or wires is impossible due to many limitations. The circuit was analyzed and optimized with the Harmonic Balance method provided by the Advanced Design System (ADS). Good performances are observed through the simulated results and confirmed by the fabrication tests in terms of RF-DC conversion efficiency, DC output voltage level and matching input impedance.
Design and analysis of high gain diode predistortionijwmn
This paper presents the design and analysis of a high gain, broadband Schottky and PIN diode based RF
pre-distortion linearizer for TWTA. The circuit is using ABCD matrix approach. The simulation is
performed using Agilent ADS software. We have proposed a new linearizer circuit which can achieve a
high gain compared to existing linearizer designs.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
2. DIODE EQUIVALENT CIRCUIT
An equivalent circuit is a combination of elements properly chosen to
best represent the actual terminal characteristics of a device, system, or
such in a particular operating p region.
In other words, once the equivalent circuit is defined, the device symbol
can be removed from a schematic and the equivalent circuit inserted in
its place without severely affecting the actual behavior of the system. The
result is often a network that can be solved using traditional circuit
analysis techniques.
3.
4. DIODE APPLICATIONS: LOAD-LINE ANALYSIS:
The applied load will normally have an important impact on the point or region
of operation of a device. If the analysis is performed in a graphical manner, a
line can be drawn on the characteristics of the device that represents the
applied load. The intersection of the load line with the characteristics will
determine the point of operation of the system. Such an analysis is, for obvious
reasons, called load-line analysis
5. If we set VD =0 V in Eq. (2.1) and solve for ID, we have the magnitude of ID on The vertical axis.
Therefore, with VD =0 V, Eq. (2.1) becomes:
6.
7.
8. EXAMPLE(2.1):
For the series diode configuration of Fig. 2.3a employing the diode characteristics of
Fig. 2.3b determine: (a) VDQ and IDQ. (b) VR.
9.
10.
11.
12. SERIES DIODE CONFIGURATIONS WITH DC INPUTS
In general, a diode is in the on state if the current established by the applied sources is such that
its direction matches that of the arrow in the diode symbol, and VD≥ 0.7V for silicon and VD ≥
0.3V for germanium.
13.
14.
15. The diode is in the “off” state, resulting in the equivalent circuit of Fig. 2.6. Due to the open
circuit, the diode current is 0 A and the voltage across the resistor R is the following: