This document discusses high voltage direct current (HVDC) transmission technology. It provides 3 key points:
1) HVDC transmission allows power transmission between AC networks with different frequencies or those that cannot synchronize, and is not limited by inductive and capacitive parameters like AC transmission.
2) The main components of an HVDC system include thyristor valves, converter transformers, smoothing reactors, harmonic filters, surge arresters, DC transmission circuits, and control and protection systems.
3) The main types of HVDC configurations are back-to-back converters for connecting adjacent AC grids, monopolar long-distance transmission using ground or metallic return paths, and bipolar long-distance transmission using common ground or
HVDC Bridge and Station Configurations
1. General HVDC – HVAC Comparisons
2. Components of a Converter Bridge
3. HVDC scheme configurations
Operation of the HVDC converter
1. General assumptions
2. Rectifier operation with uncontrolled valves and X = 0
3. Rectifier operation with controlled valves and X = 0
4. Rectifier operation with controlled valves and X 0
5. Inverter operation with controlled valves and X 0
6. Commutation and Commutation Failure
7. Reactive Power Requirements
8. Short-circuit capacity requirements for an HVDC terminal.
9. Harmonics and filtering on the AC and DC sides
Introduction, Operation of 12-pulse converter as receiving and sending terminals of HVDC system, Equipment required for HVDC System and their significance, Comparison of AC and DC transmission, Control of HVDC transmission
HVDC Bridge and Station Configurations
1. General HVDC – HVAC Comparisons
2. Components of a Converter Bridge
3. HVDC scheme configurations
Operation of the HVDC converter
1. General assumptions
2. Rectifier operation with uncontrolled valves and X = 0
3. Rectifier operation with controlled valves and X = 0
4. Rectifier operation with controlled valves and X 0
5. Inverter operation with controlled valves and X 0
6. Commutation and Commutation Failure
7. Reactive Power Requirements
8. Short-circuit capacity requirements for an HVDC terminal.
9. Harmonics and filtering on the AC and DC sides
Introduction, Operation of 12-pulse converter as receiving and sending terminals of HVDC system, Equipment required for HVDC System and their significance, Comparison of AC and DC transmission, Control of HVDC transmission
High Voltage Direct Current Transmission SystemNadeem Khilji
The development of HVDC (High Voltage Direct Current) transmission system dates back to the 1930s when mercury arc rectifiers were invented. Since the 1960s, HVDC transmission system is now a mature technology and has played a vital part in both long distance transmission and in the interconnection of systems. Transmitting power at high voltage and in DC form instead of AC is a new technology proven to be economic and simple in operation which is HVDC transmission. HVDC transmission systems, when installed, often form the backbone of an electric power system. They combine high reliability with a long useful life. An HVDC link avoids some of the disadvantages and limitations of AC transmission. HVDC transmission refers to that the AC power generated at a power plant is transformed into DC power before its transmission. At the inverter (receiving side), it is then transformed back into its original AC power and then supplied to each household. Such power transmission method makes it possible to transmit electric power in an economic way.
HVDC (high-voltage direct current) is a highly efficient alternative for transmitting large amounts of electricity over long distances and for special purpose applications.
Basics of HVDC, its components, working & classification of HVDC system, comparison of HVDC & HVAC, advantages and disadvantages of HVDC all are discussed here.
HVDC Transmission system is a combination of AC and DC systems, first, the generated AC voltage is converted into DC at the transmission end, and when it reaches the receiving end DC is inverted to AC for distribution purposes. So, in order to carry out this operation, we need conversion devices for both ends of the transmission line.
HVDC Transmission system helps in reducing power losses and improves the efficiency of the transmission system. Besides, the HVDC system is more economical as compared to HVAC but only for long distances (more than 600km).
HVDC (High Voltage Direct Current) Transmission system is more economical for the transmission of power over long distances as compared to AC transmission.
Learn more about HVDC at https://www.allumiax.com/blog/high-voltage-direct-current-hvdc-transmission
Flexible AC Transmission System (FACTS):
Alternating current transmission systems incorporating power electronic-based and other static controllers to enhance controllability and increase power transfer capability.
FACTS Controller:
What is FACTS? A power electronic-based system and other static equipment that provide control of one or more AC transmission system parameters.
Basic types of FACTS Controllers Based on the connection, generally FACTS controller can be classified as follows: Series controllers
Shunt controllers
Combined series-series controllers
Combined series-shunt controllers
A power system control is required to maintain a continuous balance between power generation and load demand. Load Frequency Controller and Automatic Voltage Regulator play an important role in maintaining constant frequency and voltage in order to ensure the reliability of electric power.
This PPT was crate for my seminar presentation and upload for help and providing information about FAULT ANALYSIS IN HVDC & HVAC TRANSMISSION LINE and basic idea of HVDC System
Extra high voltage long ac transmission linesShivagee Raj
From economical point of view designing of transmission line system is very important in the electricity supply system. Extra High Voltage Transmission Lines are best suited for transmission of bulk power.
High Voltage Direct Current Transmission SystemNadeem Khilji
The development of HVDC (High Voltage Direct Current) transmission system dates back to the 1930s when mercury arc rectifiers were invented. Since the 1960s, HVDC transmission system is now a mature technology and has played a vital part in both long distance transmission and in the interconnection of systems. Transmitting power at high voltage and in DC form instead of AC is a new technology proven to be economic and simple in operation which is HVDC transmission. HVDC transmission systems, when installed, often form the backbone of an electric power system. They combine high reliability with a long useful life. An HVDC link avoids some of the disadvantages and limitations of AC transmission. HVDC transmission refers to that the AC power generated at a power plant is transformed into DC power before its transmission. At the inverter (receiving side), it is then transformed back into its original AC power and then supplied to each household. Such power transmission method makes it possible to transmit electric power in an economic way.
HVDC (high-voltage direct current) is a highly efficient alternative for transmitting large amounts of electricity over long distances and for special purpose applications.
Basics of HVDC, its components, working & classification of HVDC system, comparison of HVDC & HVAC, advantages and disadvantages of HVDC all are discussed here.
HVDC Transmission system is a combination of AC and DC systems, first, the generated AC voltage is converted into DC at the transmission end, and when it reaches the receiving end DC is inverted to AC for distribution purposes. So, in order to carry out this operation, we need conversion devices for both ends of the transmission line.
HVDC Transmission system helps in reducing power losses and improves the efficiency of the transmission system. Besides, the HVDC system is more economical as compared to HVAC but only for long distances (more than 600km).
HVDC (High Voltage Direct Current) Transmission system is more economical for the transmission of power over long distances as compared to AC transmission.
Learn more about HVDC at https://www.allumiax.com/blog/high-voltage-direct-current-hvdc-transmission
Flexible AC Transmission System (FACTS):
Alternating current transmission systems incorporating power electronic-based and other static controllers to enhance controllability and increase power transfer capability.
FACTS Controller:
What is FACTS? A power electronic-based system and other static equipment that provide control of one or more AC transmission system parameters.
Basic types of FACTS Controllers Based on the connection, generally FACTS controller can be classified as follows: Series controllers
Shunt controllers
Combined series-series controllers
Combined series-shunt controllers
A power system control is required to maintain a continuous balance between power generation and load demand. Load Frequency Controller and Automatic Voltage Regulator play an important role in maintaining constant frequency and voltage in order to ensure the reliability of electric power.
This PPT was crate for my seminar presentation and upload for help and providing information about FAULT ANALYSIS IN HVDC & HVAC TRANSMISSION LINE and basic idea of HVDC System
Extra high voltage long ac transmission linesShivagee Raj
From economical point of view designing of transmission line system is very important in the electricity supply system. Extra High Voltage Transmission Lines are best suited for transmission of bulk power.
in this presentation i have completely described the basic constriction and working of Surge Arresters so that you will find it easy to understand and it can be easily delivered to the listeners
High Voltage Direct Current Transmission System ReportNadeem Khilji
The development of HVDC (High Voltage Direct Current) transmission system dates back to the 1930s when mercury arc rectifiers were invented. Since the 1960s, HVDC transmission system is now a mature technology and has played a vital part in both long distance transmission and in the interconnection of systems. Transmitting power at high voltage and in DC form instead of AC is a new technology proven to be economic and simple in operation which is HVDC transmission. HVDC transmission systems, when installed, often form the backbone of an electric power system. They combine high reliability with a long useful life. An HVDC link avoids some of the disadvantages and limitations of AC transmission. HVDC transmission refers to that the AC power generated at a power plant is transformed into DC power before its transmission. At the inverter (receiving side), it is then transformed back into its original AC power and then supplied to each household. Such power transmission method makes it possible to transmit electric power in an economic way.
Alternating current (AC) is the main driving force in the industries and residential areas, but for the long transmission line (more than 650 KM) AC transmission is more expensive than that of direct current (DC). Technically, AC transmission line control is more complicated because of the frequency. DC transmission does not have these limitations, which has led to build long HVDC transmission lines over the last 40 years. HVDC technology made possible to transfer bulk power over long distances.
The presentation gives you the overview of the High Voltage Direct current and Flexible AC transmission systems.
In the presentation, there is the depiction of advantages of Direct current over Alternate current, the current implementation of FACTS around the globe
The Solar System[c] is the gravitationally bound system of the Sun and the objects that orbit it. The largest of such objects are the eight planets, in order from the Sun: four terrestrial planets named Mercury, Venus, Earth and Mars, two gas giants named Jupiter and Saturn, and two ice giants named Uranus and Neptune. The terrestrial planets have a definite surface and are mostly made of rock and metal. The gas giants are mostly made of hydrogen and helium, while the ice giants are mostly made of 'volatile' substances such as water, ammonia, and methane. In some texts, these terrestrial and giant planets are called the inner Solar System and outer Solar System planets respectively.
International Journal of Engineering Research and Development (IJERD)IJERD Editor
journal publishing, how to publish research paper, Call For research paper, international journal, publishing a paper, IJERD, journal of science and technology, how to get a research paper published, publishing a paper, publishing of journal, publishing of research paper, reserach and review articles, IJERD Journal, How to publish your research paper, publish research paper, open access engineering journal, Engineering journal, Mathemetics journal, Physics journal, Chemistry journal, Computer Engineering, Computer Science journal, how to submit your paper, peer reviw journal, indexed journal, reserach and review articles, engineering journal, www.ijerd.com, research journals,
yahoo journals, bing journals, International Journal of Engineering Research and Development, google journals, hard copy of journal
Conventional and emerging converter technologies in hvdc power transmission s...Naveed Shahzad
The efficiency of HVDC system is primarily associated with power electronic converters which are playing the key role in transforming AC to DC and vice versa. There have been several converter topologies known and implemented in HVDC system throughout the world, however the major converter topologies are line commutated-current source converters (CSC) and self-commutated voltage source converters (VSC). This presentation provides an overview and comparison of CSC and VSC converters including their applications, advantages, limitations and new technological advancement related to CSC, and VSC including 2 level VSC and 3 level VSC and newer modular multilevel converter (MMC) topologies.
Control and Analysis of VSC Based High Voltage DC Transmissionijsrd.com
High Voltage Direct Current system based on Voltage Source Converters (VSC-HVDC) is becoming a more effective, solution for long distance power transmission especially for off-shore wind plants and supplying power to remote regions Confronting with an increasing demand of power, there is a need to explore the most efficient and reliable bulk power transmission system. Rapid development in the field of power electronics devices especially Insulated Gate Bipolar Transistors (IGBTs) has led to the High Voltage Direct Current (HVDC) transmission based on Voltage Source Converters (VSCs).Since VSCs do not require commutating voltage from the connected ac grid, they are effective in supplying power to isolated and remote loads. Due to its advantages, it is possible that VSC-HVDC will be one of the most important components of power systems in the future. The VSC based HVDC transmission system mainly consists of two converter stations connected by a DC cable. This paper presents the performance analysis of VCS based HVDC transmission system. In this paper a 75kM long VSC HVDC system is simulated for various faults on the ACSide of the receiving station using MATLAB/SIMULINK. The data has been analyzed and a method is proposed to classify the faults by using back propagation algorithm. The simulated results presented in this paper are in good agreement with the published work.
Smart TV Buyer Insights Survey 2024 by 91mobiles.pdf91mobiles
91mobiles recently conducted a Smart TV Buyer Insights Survey in which we asked over 3,000 respondents about the TV they own, aspects they look at on a new TV, and their TV buying preferences.
GDG Cloud Southlake #33: Boule & Rebala: Effective AppSec in SDLC using Deplo...James Anderson
Effective Application Security in Software Delivery lifecycle using Deployment Firewall and DBOM
The modern software delivery process (or the CI/CD process) includes many tools, distributed teams, open-source code, and cloud platforms. Constant focus on speed to release software to market, along with the traditional slow and manual security checks has caused gaps in continuous security as an important piece in the software supply chain. Today organizations feel more susceptible to external and internal cyber threats due to the vast attack surface in their applications supply chain and the lack of end-to-end governance and risk management.
The software team must secure its software delivery process to avoid vulnerability and security breaches. This needs to be achieved with existing tool chains and without extensive rework of the delivery processes. This talk will present strategies and techniques for providing visibility into the true risk of the existing vulnerabilities, preventing the introduction of security issues in the software, resolving vulnerabilities in production environments quickly, and capturing the deployment bill of materials (DBOM).
Speakers:
Bob Boule
Robert Boule is a technology enthusiast with PASSION for technology and making things work along with a knack for helping others understand how things work. He comes with around 20 years of solution engineering experience in application security, software continuous delivery, and SaaS platforms. He is known for his dynamic presentations in CI/CD and application security integrated in software delivery lifecycle.
Gopinath Rebala
Gopinath Rebala is the CTO of OpsMx, where he has overall responsibility for the machine learning and data processing architectures for Secure Software Delivery. Gopi also has a strong connection with our customers, leading design and architecture for strategic implementations. Gopi is a frequent speaker and well-known leader in continuous delivery and integrating security into software delivery.
Kubernetes & AI - Beauty and the Beast !?! @KCD Istanbul 2024Tobias Schneck
As AI technology is pushing into IT I was wondering myself, as an “infrastructure container kubernetes guy”, how get this fancy AI technology get managed from an infrastructure operational view? Is it possible to apply our lovely cloud native principals as well? What benefit’s both technologies could bring to each other?
Let me take this questions and provide you a short journey through existing deployment models and use cases for AI software. On practical examples, we discuss what cloud/on-premise strategy we may need for applying it to our own infrastructure to get it to work from an enterprise perspective. I want to give an overview about infrastructure requirements and technologies, what could be beneficial or limiting your AI use cases in an enterprise environment. An interactive Demo will give you some insides, what approaches I got already working for real.
Encryption in Microsoft 365 - ExpertsLive Netherlands 2024Albert Hoitingh
In this session I delve into the encryption technology used in Microsoft 365 and Microsoft Purview. Including the concepts of Customer Key and Double Key Encryption.
DevOps and Testing slides at DASA ConnectKari Kakkonen
My and Rik Marselis slides at 30.5.2024 DASA Connect conference. We discuss about what is testing, then what is agile testing and finally what is Testing in DevOps. Finally we had lovely workshop with the participants trying to find out different ways to think about quality and testing in different parts of the DevOps infinity loop.
Elevating Tactical DDD Patterns Through Object CalisthenicsDorra BARTAGUIZ
After immersing yourself in the blue book and its red counterpart, attending DDD-focused conferences, and applying tactical patterns, you're left with a crucial question: How do I ensure my design is effective? Tactical patterns within Domain-Driven Design (DDD) serve as guiding principles for creating clear and manageable domain models. However, achieving success with these patterns requires additional guidance. Interestingly, we've observed that a set of constraints initially designed for training purposes remarkably aligns with effective pattern implementation, offering a more ‘mechanical’ approach. Let's explore together how Object Calisthenics can elevate the design of your tactical DDD patterns, offering concrete help for those venturing into DDD for the first time!
State of ICS and IoT Cyber Threat Landscape Report 2024 previewPrayukth K V
The IoT and OT threat landscape report has been prepared by the Threat Research Team at Sectrio using data from Sectrio, cyber threat intelligence farming facilities spread across over 85 cities around the world. In addition, Sectrio also runs AI-based advanced threat and payload engagement facilities that serve as sinks to attract and engage sophisticated threat actors, and newer malware including new variants and latent threats that are at an earlier stage of development.
The latest edition of the OT/ICS and IoT security Threat Landscape Report 2024 also covers:
State of global ICS asset and network exposure
Sectoral targets and attacks as well as the cost of ransom
Global APT activity, AI usage, actor and tactic profiles, and implications
Rise in volumes of AI-powered cyberattacks
Major cyber events in 2024
Malware and malicious payload trends
Cyberattack types and targets
Vulnerability exploit attempts on CVEs
Attacks on counties – USA
Expansion of bot farms – how, where, and why
In-depth analysis of the cyber threat landscape across North America, South America, Europe, APAC, and the Middle East
Why are attacks on smart factories rising?
Cyber risk predictions
Axis of attacks – Europe
Systemic attacks in the Middle East
Download the full report from here:
https://sectrio.com/resources/ot-threat-landscape-reports/sectrio-releases-ot-ics-and-iot-security-threat-landscape-report-2024/
LF Energy Webinar: Electrical Grid Modelling and Simulation Through PowSyBl -...DanBrown980551
Do you want to learn how to model and simulate an electrical network from scratch in under an hour?
Then welcome to this PowSyBl workshop, hosted by Rte, the French Transmission System Operator (TSO)!
During the webinar, you will discover the PowSyBl ecosystem as well as handle and study an electrical network through an interactive Python notebook.
PowSyBl is an open source project hosted by LF Energy, which offers a comprehensive set of features for electrical grid modelling and simulation. Among other advanced features, PowSyBl provides:
- A fully editable and extendable library for grid component modelling;
- Visualization tools to display your network;
- Grid simulation tools, such as power flows, security analyses (with or without remedial actions) and sensitivity analyses;
The framework is mostly written in Java, with a Python binding so that Python developers can access PowSyBl functionalities as well.
What you will learn during the webinar:
- For beginners: discover PowSyBl's functionalities through a quick general presentation and the notebook, without needing any expert coding skills;
- For advanced developers: master the skills to efficiently apply PowSyBl functionalities to your real-world scenarios.
Builder.ai Founder Sachin Dev Duggal's Strategic Approach to Create an Innova...Ramesh Iyer
In today's fast-changing business world, Companies that adapt and embrace new ideas often need help to keep up with the competition. However, fostering a culture of innovation takes much work. It takes vision, leadership and willingness to take risks in the right proportion. Sachin Dev Duggal, co-founder of Builder.ai, has perfected the art of this balance, creating a company culture where creativity and growth are nurtured at each stage.
3. Contents
Chapter Theme Page
1 Why High Voltage Direct Current? 4
2 Main Types of HVDC Schemes 6
3 Converter Theory 8
4 Principle Arrangement
of an HVDC Transmission Project 11
5 Main Components 14
5.1 Thyristor Valves 14
5.2 Converter Transformer 18
5.3 Smoothing Reactor 20
5.4 Harmonic Filters 22
5.4.1 AC Harmonic Filter 22
5.4.2 DC Harmonic Filter 25
5.4.3 Active Harmonic Filter 26
5.5 Surge Arrester 28
5.6 DC Transmission Circuit 31
5.6.1 DC Transmission Line 31
5.6.2 DC Cable 32
5.6.3 High Speed DC Switches 34
5.6.4 Earth Electrode 36
5.7 Control Protection 38
6 System Studies, Digital Models,
Design Specifications 45
7 Project Management 46
3
4. 1 Why High Voltage
Direct Current?
1.1 Highlights from the High Voltage Direct In 1941, the first contract for a commercial HVDC
C
urrent (HVDC) History system was signed in Germany: 60 MW were to be
supplied to the city of Berlin via an underground
The transmission and distribution of electrical energy cable of 115 km length. The system with ±200 kV
started with direct current. In 1882, a 50-km-long and 150 A was ready for energizing in 1945. It was
2-kV DC transmission line was built between Miesbach never put into operation.
and Munich in Germany. At that time, conversion
between reasonable consumer voltages and higher Since then, several large HVDC systems have been
DC transmission voltages could only be realized by realized with mercury arc valves.
means of rotating DC machines. The replacement of mercury arc valves by thyristor
valves was the next major development. The first
In an AC system, voltage conversion is simple. thyristor valves were put into operation in the late
An AC transformer allows high power levels and nineteen-seventies.
high insulation levels within one unit, and has The outdoor valves for Cahora Bassa were designed
low losses. It is a relatively simple device, which with oil-immersed thyristors with parallel/series
requires little maintenance. Further, a three-phase connection of thyristors and an electromagnetic
synchronous generator is superior to a DC generator firing system.
in every respect. For these reasons, AC technology Further development went via air-insulated air-
was introduced at a very early stage in the develop- cooled valves to the air- insulated water-cooled
ment of electrical power systems. It was soon design, which is still state of the art in HVDC valve
accepted as the only feasible technology for genera- design.
tion, transmission and distribution of electrical The development of thyristors with higher current
energy. and voltage ratings has eliminated the need for
parallel connection and reduced the number of
However, high-voltage AC transmission links have series-connected thyristors per valve. The develop-
disadvantages, which may compel a change to ment of light-triggered thyristors has further reduced
DC technology: the overall number of components and thus contrib-
■■ Inductive and capacitive elements of overhead lines uted to increased reliability.
and cables put limits to the transmission capacity Innovations in almost every other area of HVDC have
and the transmission distance of AC transmission been constantly adding to the reliability of this tech-
links. nology with economic benefits for users throughout
■■ This limitation is of particular significance for the world.
cables. Depending on the required transmission
capacity, the system frequency and the loss evalua- Self-Commutated Voltage Sourced Converters
tion, the achievable transmission distance for Voltage sourced converters require semiconductor
an AC cable will be in the range of 40 to 100 km. devices with turn-off capability. The development
It will mainly be limited by the charging current. of Insulated Gate Bipolar Transistors (IGBT) with high
■■ Direct connection between two AC systems with voltage ratings have accelerated the development
different frequencies is not possible. of voltage sourced converters for HVDC applications
■■ Direct connection between two AC systems with in the lower power range.
the same frequency or a new connection within a The main characteristics of the voltage sourced
meshed grid may be impossible because of system converters are a compact design, four-quadrant
instability, too high short-circuit levels or undesir- operation capability and high losses.
able power flow scenarios. Siemens is offering voltage sourced converters for
HVDC applications with ratings up to 250 MW under
Engineers were therefore engaged over generations the trade name HVDCplus Power Link Universal
in the development of a technology for DC transmis- Systems.
sions as a supplement to the AC transmissions. This paper focuses upon HVDC transmission systems
with high ratings, i.e. with line-commutated current
Line-Commutated Current Sourced Converters sourced converters.
The invention of mercury arc rectifiers in the nine-
teen-thirties made the design of line-commutated HVDC = high voltage direct current
current sourced converters possible. DC = direct current
AC = alternating current
4 IGBT = insulated gate bipolar transistor
5. 1.2 Technical Merits of HVDC 1.4 Environmental Issues
The advantages of a DC link over an AC link are: An HVDC transmission system is basically environment-
■■ A DC link allows power transmission between friendly because improved energy transmission possi-
AC networks with different frequencies or networks, bilities contribute to a more efficient utilization of
which can not be synchronized, for other reasons. existing power plants.
■■ Inductive and capacitive parameters do not limit The land coverage and the associated right-of-way
the transmission capacity or the maximum length cost for an HVDC overhead transmission line is not
of a DC overhead line or cable. The conductor cross as high as that of an AC line. This reduces the visual
section is fully utilized because there is no skin effect. impact and saves land compensation for new projects.
It is also possible to increase the power transmission
For a long cable connection, e.g. beyond 40 km, capacity for existing rights of way. A comparison
HVDC will in most cases offer the only technical between a DC and an AC overhead line is shown
solution because of the high charging current of in Fig. 1-2.
an AC cable. This is of particular interest for trans-
mission across open sea or into large cities where
a DC cable may provide the only possible solution.
■■ A digital control system provides accurate and
fast control of the active power flow.
■■ Fast modulation of DC transmission power can be
used to damp power oscillations in an AC grid and
thus improve the system stability.
1.3 Economic Considerations
For a given transmission task, feasibility studies
are carried out before the final decision on imple-
mentation of an HVAC or HVDC system can be taken.
Fig.1-1 shows a typical cost comparison curve AC-tower DC-tower
between AC and DC transmission considering:
■■ AC vs. DC station terminal costs
■■ AC vs. DC line costs
■■ AC vs. DC capitalised value of losses
Fig. 1-2: Typical transmission line structures
The DC curve is not as steep as the AC curve because for approx. 1000 MW
of considerably lower line costs per kilometre. For
long AC lines the cost of intermediate reactive power There are, however, some environmental issues
compensation has to be taken into account. which must be considered for the converter stations.
The break-even distance is in the range of 500 to The most important ones are:
■■ Audible noise
800 km depending on a number of other factors, like
■■ Visual impact
country-specific cost elements, interest rates for project
■■ Electromagnetic compatibility
financing, loss evaluation, cost of right of way etc.
■■ Use of ground or sea return path
in monopolar operation
Costs
In general, it can be said that an HVDC system is
Total AC Cost
highly compatible with any environment and can
Total DC Cost be integrated into it without the need to compromise
on any environmentally important issues of today.
DC Losses
AC Losses
DC Line
AC Line
DC Terminals
AC Terminals
Break-Even Transmission
Distance Distance
Fig. 1-1: Total cost/distance
5
6. 2 Main Types of HVDC Schemes
2.1 DC Circuit
The main types of HVDC converters are distinguished
by their DC circuit arrange-ments. The following
equivalent circuit is a simplified representation of
the DC circuit of an HVDC pole.
Ud
Ud1 Ud2
Fig. 2-3: Back-to-back converter Station Vienna Southeast
Fig. 2-1: Equivalent DC circuit
2.3 Monopolar Long-Distance Transmissions
The current, and thus the power flow, is controlled For very long distances and in particular for very
by means of the difference between the controlled long sea cable transmissions, a return path with
voltages. The current direction is fixed and the power ground/sea electrodes will be the most feasible
direction is controlled by means of the voltage polarity. solution.
The converter is described in the next section.
2.2 Back-to-Back Converters
The expression Back-to-back indicates that the recti- HVDC
AC System 2
AC System 1
fier and inverter are located in the same station. Cable/OHL
Back-to-back converters are mainly used for power
transmission between adjacent AC grids which can
not be synchronized. They can also be used within Electrodes
a meshed grid in order to achieve a defined power flow.
HVDC
Fig. 2-4: Monopole with ground return path
AC System 1
AC System 2
In many cases, existing infrastructure or environmental
constraints prevent the use of electrodes. In such cases,
a metallic return path is used in spite of increased
cost and losses.
HVDC
AC System 1
AC System 2
Fig. 2-2: Back-to-back converter
Cable/OHL
HVDC = high voltage direct current
LVDC
DC = direct current
AC = alternating current
Ud = DC voltage 12-pulse
I d = DC current
OHL = overhead line
LVDC = low voltage direct current
Fig. 2-5: Monopole with metallic return path
6
7. 2.4 Bipolar Long-Distance Transmissions
A bipole is a combination of two poles in such a way
HVDC
that a common low voltage return path, if available,
Cable/OHL
will only carry a small unbalance current during normal
AC System 1
AC System 2
Electrodes
operation.
This configuration is used if the required transmission
capacity exceeds that of a single pole. It is also used
HVDC
if requirement to higher energy availability or lower Cable/OHL
load rejection power makes it necessary to split the
capacity on two poles.
During maintenance or outages of one pole, it is still Fig. 2-8: in monopolar metallic return
possible to transmit part of the power. More than 50 % operation (converter pole outage)
of the transmission capacity can be utilized, limited
by the actual overload capacity of the remaining pole. 2.4.2 Bipole with Dedicated Metallic Return Path
The advantages of a bipolar solution over a solution for Monopolar Operation
with two monopoles are reduced cost due to one If there are restrictions even to temporary use of
common or no return path and lower losses. The main electrodes, or if the transmission distance is relatively
disadvantage is that unavailability of the return path short, a dedicated LVDC metallic return conductor
with adjacent components will affect both poles. can be considered as an alternative to a ground
return path with electrodes.
2.4.1 Bipole with Ground Return Path
This is a commonly used configuration for a bipolar
transmission system. The solution provides a high HVDC
degree of flexibility with respect to operation with Cable/OHL
AC System 1
AC System 2
reduced capacity during contingencies or maintenance.
LVDC
Cable/OHL
HVDC
HVDC Cable/OHL
Cable/OHL
AC System 1
AC System 2
Electrodes
Fig. 2-9: in bipolar balanced operation (normal)
HVDC 2.4.3 Bipole without Dedicated Return Path
Cable/OHL for Monopolar Operation
A scheme without electrodes or a dedicated metallic
return path for monopolar operation will give the
Fig. 2-6: in bipolar balanced operation (normal)
lowest initial cost.
Upon a single-pole fault, the current of the sound
pole will be taken over by the ground return path HVDC
and the faulty pole will be isolated. Cable/OHL
AC System 1
AC System 2
HVDC HVDC
Cable/OHL Cable/OHL
AC System 1
AC System 2
Electrodes
Fig. 2-10: in bipolar balanced operation (normal)
HVDC
Cable/OHL Monopolar operation is possible by means of bypass
switches during a converter pole outage, but not
during an HVDC conductor outage.
Fig. 2-7: in monopolar ground return
A short bipolar outage will follow a converter pole
operation (converter pole or OHL outage) outage before the bypass operation can be established.
Following a pole outage caused by the converter,
the current can be commutated from the ground
return path into a metallic return path provided
by the HVDC conductor of the faulty pole.
7
8. 3 Converter Theory
3.1 Bridge Circuit Function The angle between the time at which the valve voltage
Current flows through the valves when the voltage becomes positive and the firing time (start of commu-
between the anode and cathode is positive. For the tation) is referred to as the firing delay. Fig. 3-2 shows
valve to commutate the current, there must be a that for a firing delay of 90°, the average voltage equals
positive potential (voltage), and the thyristor must zero. i.e. the positive and negative areas of the curve –
have firing pulses. In the reverse direction, i.e. when voltage against time – cancel each other out. No active
the potential between anode and cathode is negative, power flows through the converter. When the firing
a firing pulse has no effect. The flow of current in delay is greater than 90°, the negative voltage/time
a valve ends when the voltage between anode and areas dominate, and the polarity of the average direct
cathode becomes negative. The instant when current voltage changes. Due to physical reasons, the direction
begins to flow through a valve, or to commutate of the current does not change. (The thyristor valves
from one valve to another, can be delayed by post- conduct current only in one direction.) When the direc-
poning the firing. This method permits the average tion of energy flow is reversed, the delivery changes
value of the outgoing voltage of the rectifier to be to the supply side. The rectifier becomes an inverter
changed. The firing pulses are generated by synchro- which delivers energy to the AC network.
nizing the network using an elec-tronic control device.
These pulses can be displaced from their ”natural The average value of the direct voltage as a function
firing“ point, which is the point where the two phase of the firing delay is given by:
voltages intersect. The method of firing-pulse dis- Udiα = 1.35 * UL * cos α
placement is called phase control. UL = secondary side line voltage
α = firing angle
γ = extinction angle
DC current in each valve and phase
1 3 5 1
L1 L2 L3
60° 0°
0° 120° U d Udi
6 2 4 6 2 ω t
ld = 0°
0°
i1
i2
i3
i4 ω t
= 60°
60°
i5
i6
ω t = 90°
iL 90 °
1 = 90°
iL
2
iL
3
150° ω t = 150°
ld = 30°
1 3 5
L1
L2 Ud 180°
ω t = 180°
L3 = 0°
4 6 2
Fig. 3-1: Six-pulse converter bridge Fig. 3-2: DC voltage of bridge converter as a function of α
8
9. 3.2 12-Pulse Group and Converter Transformer 3.3 Reactive Power as a Function of Load
HVDC converters are usually built as 12-pulse circuits. The curve of reactive power demand of an
This is a serial connection of two fully controlled HVDC station with changing active power P
6-pulse converter bridges and requires two 3-phase can be calculated from equation:
systems which are spaced apart from each other by
30 electrical degrees. The phase difference effected Q = P * tan [ arc cos ( cos α - dx)]
to cancel out the 6-pulse harmonics on the AC and
DC side. In Fig. 3-5, the reactive power demand of a converter
is presented under three different control methods.
If the terminal DC voltage Ud and the firing angle
3 1 2 α (or the extinction angle γ of an inverter) are held
constant, curve (1) will be obtained. If, however,
Uv is held constant (Udi = const regulation), a linear
curve such as (2) is obtained. The power of a con-
4
verter can also be changed when the (nominal)
current is held constant by varying the DC voltage.
Curve (3) shows the reactive power demand for this
control method. It is important to note that the entire
1 Valve Branch area between curves (1) and (3) is available for reactive
2 Double Valve
3 Valve Tower power control. Each point within this area can be set
4 6-pulse Bridge by the selection of firing angles α and β (or γ).
Fig. 3-3: Arrangement of the valve branches in a 12-pulse bridge
= 60°
Q/PN
Udi 1.2
3
1.0
ω t 0.8
0.6
Secondary Voltage
of the Transformer 0.4 2
0.2 1
Basic AC Current
P/PN
0.5 1.0
1 Ud = const; = const ( = const)
2 Ud = const; Uv = const
3 Id = const
Fig. 3-4:Current displacement with angle control Fig. 3-5:Reactive power demand of an HVDC converter
HVDC DC Circuit d x = relative inductive voltage drop
UdN = PdN Rec/IdN U v = valve voltage
UdN = nominal DC voltage 12-pulse U d = DC voltage 12-pulse
IdN = nominal DC current α = firing angle
PdNRec = nominal DC active power β = 180°-α
at the rectifier γ = extinction angle
9
10. 3.4 Reactive Power Control
The possibility of electronic reactive power control
420 kV 50 Hz 420 kV 50 Hz as demonstrated in the preceding section is used
only to a very limited degree in HVDC technology.
This is due to economic reasons. Both control reac-
tive power and commutation reactive power are
increased by the reduction of the DC voltage and
the corresponding increase of current. However,
load losses increase with the square of the current.
For this reason, application is limited to the light
loads where the necessary filter circuits produce
a considerable overcompensation for the reactive
power required by the converter.
Q = 103 Mvar Q = 103 Mvar
Fig. 3-6 depicts the reactive power control of the
Dürnrohr HVDC link. In this system, a compensation
to ± 60 Mvar was specified. Compliance with the
Q = 103 Mvar Q = 103 Mvar
Q limit is achieved by load-dependent switching of
a capacitor bank and one of the two high-pass filters.
Q = 103 Mvar Q = 103 Mvar
Electronic reactive power is used only in the light
load range. Normally, there is a difference between
the connect and disconnect points of the reactive
power elements. This provides a ”switching hysteresis”
Fig. 3-6: Reactive-power compensation and control which prevents too many switching operations or
of an HVDC back-to-back link even a ”pumping”.
Q (Mvar)
100
80
Over load
Reduced minimum load
Normal minimum load
Normal load
60
40
20
100 200 300 400 500 600 700 P (MW)
0.2 0.4 0.6 0.8 1.0 1.2 P
PN
–20
–40
–60
Electronic Capacitor
reactive bank
power
regulation High–pass filter 2
–80
High–pass filter 1
–100
Reactive-Power Balance
UAC in p.u. (AC bus voltage)
– cap. reactive-power reactive-power reactive-power reactive-power
+ ind converter AC filters reactors capacitors
QNetwork = + QConv – QFK*UAC2 + QL*UAC2 – QC*UAC2
10
11. 4 Principle Arrangement of
an HVDC Transmission Project
The Principle Arrangement of an HVDC Transmission
Project is reflected on the Moyle Interconnector
project. The HVDC stations between Northern Ireland
and Scotland are operating with the following
highlights:
■■ Direct light triggered thyristor valves for the
complete HVDC system, with 1872 thyristors
in total, with 20 % better reliability and all valve
components free from oil.
■■ Triple tuned AC filter in both stations.
■■ Unmanned stations, fully automatic remote
operation and automatic load schedule operation.
■■ Hybrid optical ohmic shunt for DC current
measuring unit.
■■ Low noise station design for:
– AC filter capacitor and reactors
– Converter transformer
– Converter valve water cooling system
– DC hall with smoothing reactor
■■ Station design for DC see/land cable with
integrated return conductor and fibre optic
cable for control and communication.
Date of contract 09/99
Delivery period 27 months
System Data
Transmission capacity 2 x 250 MW
System voltages 250 kV DC
275 kV AC
Rated current 1000 A
Transmission distance 63.5 km
Moyle Interconnector
Ballycronan
More Auchencrosh Coylton
Overhead Line
Converter Station Converter Station AC Substation
Undersea Cables
Existing 275-kV Existing 275-kV
Transmission System Transmission System
Alternating Current Direct Current Alternating Current
Northern Ireland Scotland
11
12. 250 DC Power Cable. HVDC Station Auchencrosh L L
63.5 km to HVDC Station HA
DC
Ballycronan More
Northern Ireland L
VA
Smoothing Reactor L
RO G
AC-Filter
DC
Pole 1, 250 MW
kV NT IN
AC-Filter O ILD
C U
Thyristor
Valves 2 50 B
C-Shunt
Thyristor
Valves
AC-Filter 1
S
AN
Pole 2, 250 MW
TR
AC-Filter
2
ER
Smoothing Reactor 16
3
RT
AC-Filter
14
N VE
CO
AC Bus
SH
6
14
12
13. L L
HA
E 14
LV
4
EA
AR
ER
M
OR
SF
NK
11
BA
R
TO
CI
PA
CA
NT
9
8 10
HU
15
27
SWI 5 kV AC
5 15 TCH
YAR 5 6
D 7 5 6 5 6
10
8 9
9
10 10 275 kV
8 9 12 13 OHL
14
1 Quadruple Thyristor Valve 9 Disconnector
2 Converter Transformer 10 Current Transformer
3 Air Core Smoothing Reactor 11 Voltage Transformer
4 Control Room and Control Cubicle 12 Combined Current-Voltage Transformer
5 AC Filter Capacitor 13 Capacitive Voltage Transformer
6 AC Filter Reactor 14 Surge Arrester
7 AC Filter Resistor 15 Earthing Switch
8 Circuit Breaker 16 AC PLC Filter
13
14. 5 Main Components
5.1 Thyristor Valves 5.1.1 Introduction
The thyristor valves make the conversion from AC
Components into DC and thus are the central component of any
Siemens is a leading supplier of HVDC systems all HVDC converter station. The thyristor valves are of
over the world. Our components are exceeding the indoor type and air-insulated. Siemens has more
the usual quality standards and are system-tailored than 30 years experience in the development and
to the needs of the grid. manufacturing of thyristor valves and has maintained
the technical leadership by introducing new innovative
concepts such as the corrosion-free water cooling and
the self-protecting direct-light-triggered thyristor.
This directly reflects in the high reliability of these
valves.
valve valve valve
valve valve valve
valve valve valve
valve valve valve
12-pulse group
Multiple valve unit –
quadruple valve Valve
branch
Fig. 5.1-2: General arrangement of a 500 kV MVU (valve tower)
Fig. 5.1-1: Principle circuit diagram of a 12-pulse group
consisting of three quadruple valves
14
15. 5.1.2 Valve Design
The modular concept of the Siemens thyristor
valves permits different mechanical setups to best
suit each application: single, double, quadruple
valves or complete six-pulse bridges – either
free – standing or suspended from the building
structure.
For seismic requirement reasons which exist in
some regions of the world, the standard Siemens
valves for long distance transmission are suspended
from the ceiling of the valve hall. The suspension
insulators are designed to carry the weight and
additional loads originating for example from an
unbalanced weight distribution due to insulator
failure, an earthquake or during maintenance.
Connections between modules (piping of cooling
circuit, fibre optic ducts, buswork, and suspension
insulator fixtures) are flexible in order to allow
stress-free deflections of the modules inside an
MVU (multiple valve unit) structure. Figure 5.1-2
shows a typical quadruple valve tower for a 500 kV DC
system. Each valve is made up of three modules.
Four arresters, each related to one valve, are
located on one side of the valve tower. Ease of
access for maintenance purposes, if required,
is another benefit of the Siemens valve design.
By varying the number of thyristors per module
and the number of modules per valve, the same
design can be used for all transmission voltages
that may be required.
15
16. 5.1.3 Thyristor Development system faults without any limitations. In case of elec-
Thyristors are used as switches and thus the valve trically triggered thyristors (ETT), this is only possible
becomes controllable. The thyristors are made of if enough firing energy is stored long enough on the
highly pure mono-crystalline silicon. The high speed thyristor electronics.
of innovation in power electronics technology is
directly reflected in the development of the thyristor. Direct light-triggered thyristors with integrated over-
voltage protection (LTT) is now a proven technology
and the Siemens standard. It was implemented success-
Thyristor Current Thyristor Blocking
(IdN) Voltage (UDRM) fully for the first time in 1997 (Celilo Converter Station
LTT 8 of the Pacific Intertie). It shows excellent performance
and no thyristor failures or malfunction of the gating
kA kV
system have been recorded. BPA has emphasized its
Thyristor Blocking confidence in this technology in 2001 by awarding
6 Voltage 6 Siemens the contract to replace all mercury arc valves
with direct-light-triggered thyristor valves. Further-
more, this valve technology is used for the Moyle
4 4 Interconnector (2 x 250 MW), which went into
service in 2001 and is on contract for the 3000-MW,
Thyristor Current for
Long-Distance Transmission ± 500-kV Guizhou-Guangdong system.
2 2
Monitoring of the thyristor performance is achieved
by a simple voltage divider circuit made from standard
off-the-shelf resistors and capacitors; monitoring
signals are transmitted to ground potential through
1970 1980 1990 2000 2003
a dedicated set of fibre optic cables as for the ETT.
However, all electronic circuits needed for the evalu-
Fig. 5.1-3: Thyristor development ation of performance are now located at ground
potential in a protected environment, further simpli-
The high performance thyristors installed in HVDC fying the system. The extent of monitoring is the
plants today are characterized by silicon wafer same as for the ETT.
diameters of up to 5’’ (125 mm), blocking voltages
up to 8 kV and current carrying capacities up to It can be expected that this technology will become
4 kA DC. Thus no parallel thyristors need to be the industry standard in HVDC thyristor valves of the
installed in today’s HVDC systems for handling 21st century, paving the way towards maintenance-
the DC current. The required DC system voltages free thyristor valves.
are achieved by a series connection of a sufficient
number of thyristors.
Light Pipe
5.1.4 LTT (Light-Triggered Thyristor)
It has long been known that thyristors can be turned Cu Si
on by injecting photons into the gate instead of elec-
trons. The use of this new technology reduces the
number of components in the thyristor valve by up to Cu Mo
80 %. This simplification results in increased reliability
and availability of the transmission system. With LTT
technology, the gating light pulse is transmitted via Fig. 5.1-4: The optical gate pulse is transmitted directly
a fibre optic cable through the thyristor housing to the thyristor wafer
directly to the thyristor wafer and thus no elaborate
electronic circuits and auxiliary power supplies are
needed at high potential. The required gate power
is just 40 mW. The forward overvoltage protection is
integrated in the wafer. Further benefits of the direct
light triggering are the unlimited black start capability
and the operation during system undervoltage or
Cu = Copper
Si = Silicon
Mo = Molybdenum
LTT = Light-triggered thyristors
ETT = Electrically triggered thyristors
Fig. 5.1-5: Valve module with direct-light-triggered thyristor
16
17. 5.1.6 Flame Resistance
A lot of effort has been invested by Siemens
to minimize the fire risk:
■■ All oil has been eliminated from the valve and
its components. Snubber capacitors and grading
capacitors use SF6 as a replacement for
impregnating oil.
■■ Only flame-retardant and self-extinguishing
plastic materials are used.
■■ A wide separation between the modular units
ensures that any local overheating will not affect
neighbouring components.
■■ Careful design of the electrical connections avoids
Fig. 5.1-6: Silicon wafer and housing loose contacts.
of a direct-light-triggered thyristor
The past has shown that Siemens HVDC installations
5.1.5 Valve Cooling
have never been exposed to a hazardous valve fire.
Siemens has used the parallel water cooling principle
The tests performed on actual components and
for more than 25 years. No corrosion problems have
samples in the actual configuration as used in the
ever been encountered.
valve indicate that the improved design is indeed
flame-retardant and the risk of a major fire following
The thyristors are stacked in the module with a heat
a fault is extremely low or even non-existent.
sink on either side. The water connection to the heat
sinks can be designed in parallel or series as shown in
figure 5.1-7. The parallel cooling circuit provides all
thyristors with the same cooling water temperature.
This allows a better utilization of the thyristor capa-
bility. Siemens makes use of this principle, which offers
the additional advantage that electrolytic currents
through the heat sinks – the cause for electrolytic
corrosion – can be avoided by placing grading
e
lectrodes at strategic locations in the water circuit.
iemens water cooling also does not require any
S
de‑oxygenizing equipment.
d
b a c
a c
b
Fig. 5.1-7: Piping of module cooling circuit –
parallel flow (top); series flow (bottom)
a) thyristor; b) heat sink; c) connection piping; d) manifold
Fig. 5.1-8: Converter valves Sylmar HVDC station,
Los Angeles, USA
17
18. 5.2 Converter Transformer
Siemens supplies transformers which meet all
requirements concerning power, voltage, mode
of operation, low noise level, connection tech-
niques, type of cooling, transport and installation.
They also comply with special national design
requirements.
All over the world, power transformers from
Nuremberg enjoy a great reputation. What the
Nuremberg plant manufactures reflects today’s
state of the art and testifies to the highest levels
of quality and reliability. Our quality management
system is certified to DIN 9001, the world’s most
stringent standard. Our accredited test laboratories
likewise meet the latest specifications.
Project: Tian Guang
HVDC bipolar
long-distance transmission Fig. 5.2-1: Converter transformer for the Tian Guang
PN = 2 x 900 MW HVDC project during type test
Ud = ± 500 kV
Transformers: SN = 354/177/177 MVA
1-ph/3-w unit
UAC = 220 kV
5.2.1 Functions of the HVDC Converter
Transformer
The converter transformers transform the voltage
of the AC busbar to the required entry voltage of
the converter.
The 12-pulse converter requires two 3-phase systems
which are spaced apart from each other by 30 or
150 electrical degrees. This is achieved by installing
a transformer on each network side in the vector
groups Yy0 and Yd5.
At the same time, they ensure the voltage insulation
necessary in order to make it possible to connect
converter bridges in series on the DC side, as is
necessary for HVDC technology. The transformer
main insulation, therefore, is stressed by both the
AC voltage and the direct voltage potential between
valve-side winding and ground. The converter trans-
formers are equipped with on-load tap-changers
in order to provide the correct valve voltage.
Transformer Rating
STrafo Rec (6-pulse) = √2 * IdN * Usec Rec
IdN nominal DC current
Usec Rec Transformer-voltage
valve side (Rectifier)
STrafo Inv (6-pulse) = √2 * IdN * Usec Inv
Usec Inv Transformer voltage
valve side (inverter) Converter transformer for the
Three Gorges HVDC project 284 MVA, 1-ph/2-w unit
18
19. 5.2.2 Transformer Design Variations 5.2.3 HVDC Makes Special Demands on
There are several aspects which play a role in Transformers
selecting the transformer design: HVDC transformers are subject to operating conditions
that set them apart from conventional system or
Transportation Weight and Dimensions power transformers. These conditions include:
In systems of high power, weight can be an important ■■ Combined voltage stresses
consideration, in particular where transportation is ■■ High harmonics content of the operating current
difficult. The relative transportation weights of the ■■ DC premagnetization of the core
4 major design types are approximately as follows:
The valve windings which are connected to the rectifier
and the converter circuit are subject to the combined
Single-phase – two-winding transformer 1 load stress of DC and AC voltage. Added to this stress
are transient voltages from outside caused by lightning
Single-phase – three-winding transformer .6
1 strikes or switching operations.
Three-phase – two-winding transformer 2.2 The high harmonics content of the operating current
results from the virtually quadratic current blocks of the
Three-phase – three-winding transformer 3.6 power converter. The odd-numbered harmonics with
the ordinal numbers of 5, 7, 11, 13, 17 … cause addi-
tional losses in the windings and other structural parts.
The transport dimension and the weight of the
converter transformer depends on the limitations
for street, railway and shipping, especially in the
case of bridges, subways and tunnels.
19
20. 5.2.4 Main Components of the thyristor valve towers. This frequently leads
of the Converter Transformer to very high connection heights and the need to
mount the oil expansion tank at a significant height.
Core In close cooperation with the equipment design
HVDC transformers are normally single-phase department, the engineering specialists at the
transformers, whereby the valve windings for Nuremberg Transformer Plant have always been
the star and delta connection are configured able to find a design suited to every customer
either for one core with at least two main limbs requirement.
or separately for two cores with at least one main
limb, depending on the rated power and the Bushings
system voltage. Appropriately sized return limbs Compared to porcelain, composite bushings provide
ensure good decoupling for a combined arrange- better protection against dust and debris. A 15%
ment of windings. higher DC voltage testing level compared to the
windings underscores the particular safety aspect
The quality of the core sheets, the lamination of of these components.
the sheets, and the nominal induction must all
conform to special requirements covering losses, Special Tests for HVDC Transformers
noise level, over-excitation, etc. Special attention Special tests for verifying operating functionality
must be paid to the DC premagnetization of the are required for HVDC transformers. The applicable
core due to small asymmetries during operation international standards are subject to constant
and stray DC currents from the AC voltage network. further development. Separate tests with DC voltage,
The effects of DC premagnetization must be compen- switching and lightning impulse voltages cover the
sated by appropriate design and manufacturing range of different voltage loads. The 2-MV DC volt-
efforts (e.g. additional core cooling ducts, avoidance age generator in the Nuremberg Transformer Plant
of flux pinching in the core sheet). is well-suited for all required DC voltage and reverse
poling tests. The most important criterion is partial
Windings discharge. A maximum of 10 discharges over 2000 pC
The large number of parameters concerning during the last 10 minutes of the test is permitted.
transport limitations, rated power, transformer
ratio, short-circuit voltage, and guaranteed losses 5.3 Smoothing Reactor
require significant flexibility in the design of
windings. 5.3.1 Functions of the Smoothing Reactor
■■ Prevention of intermittent current
In concentric winding arrangements, star or delta ■■ Limitation of the DC fault currents
valve windings lying directly on the core have ■■ Prevention of resonance in the DC circuit
proven optimal in many cases. The line winding, ■■ Reducing harmonic currents including
normally with a tapped winding, is then mounted limitation of telephone interference
radial outside this core configuration.
Prevention of intermittent current
The valve windings with high insulation levels and The intermittent current due to the current ripple
a large portion of current harmonics make particular can cause high over-volt-ages in the transformer and
demands on the design and the quality of the wind- the smoothing reactor. The smoothing reactor is used
ing manufacturing. Together with its pressboard to prevent the current interruption at minimum load.
barriers, each limb set, including a valve, an over
voltage and a tapped winding, forms a compact Limitation of the DC fault current
unit, which is able to cope with the demand made The smoothing reactor can reduce the fault current
by voltage stress, loss dissipation, and short-circuit and its rate of rise for commutation failures and
withstand capability. DC line faults.
This is of primary importance if a long DC cable is
Tank used for the transmission. For an overhead line trans-
The unconventional tank design in HVDC transformers mission, the current stress in valves is lower than the
result from the following requirements: stress which will occur during valve short circuit.
■■ The valve-side bushing should extend
into the valve hall Prevention of resonance in the DC circuit
■■ The cooling system is mounted on the opposite The smoothing reactor is selected to avoid resonance
side to facilitate rapid transformer exchange in the DC circuit at low order harmonic frequencies like
100 or 150 Hz. This is important to avoid the amplifi-
For HVDC transformers with delta and star valve cation effect for harmonics originally from the AC
winding in one tank, the valve bushing must be system, like negative sequence and transformer
arranged so that their ends conform to the geometry saturation.
20
21. Reducing harmonic currents including limitation The wall bushing in composite design is the
of telephone interference state-of-the-art technology which provides
Limitation of interference coming from the DC over- superior insulation performance.
head line is an essential function of the DC filter
circuits. However, the smoothing reactor also plays
an important role to reduce harmonic currents acting
as a series impedance.
5.3.2 Sizing of the smoothing Reactor
While the current and voltage rating of the smooth-
ing reactor can be specified based on the data of the
DC circuit, the inductance is the determining factor
in sizing the reactor.Taking all design aspects above
into account, the size of smoothing reactors is often
selected in the range of 100 to 300 mH for long-
distance DC links and 30 to 80 mH for back-to-back
stations.
5.3.3 Arrangement of the Smoothing Reactor
In an HVDC long-distance transmission system, it
seems quite logical that the smoothing reactor will
be connected in series with the DC line of the station
pole. This is the normal arrangement. However in
Fig. 5.3-1: Oil-insulated smoothing reactor –
back-to-back schemes, the smoothing reactor can
Three Gorges project
also be connected to the low-voltage terminal. ■ Inductance: 270 mH
■ Rated voltage: 500 kV DC
5.3.4 Reactor Design Alternatives ■ Rated current: 3000 A DC
There are basically two types of reactor design:
■■ Air-insulated dry-type reactors
■■ Oil-insulated reactors in a tank
The reactor type should be selected taking the
following aspects into consideration:
■■ Inductance
■■ Costs
■■ Maintenance and location of spare units
■■ Seismic requirements
An advantage of the dry-type reactor is that main-
taining spare units (to the extent necessary) is not
very expensive because they usually consist of several
partial coils. However for very large inductances it
is possible to have more than one unit and it could
be a problem if much space is not available.
In high seismic regions, setting them on post-insulators
or on an insulating platform is a possible problem.
Oil-insulated smoothing reactors are then the preferred
solution.
The oil-insulated reactor is economical for very
high power (Id2 * Ldr). It is the best option for
regions with high seismic requirements.
One bushing of the oil-insulated smoothing reactor
penetrates usually into the valve hall, while the Fig. 5.3-2: Air-insulated smoothing reactor –
other bushing is normally in a vertical position. Tian Guang project
For the air-insulated dry-type smoothing reactor, ■ Inductance: 150 mH
a wall bushing is needed to connect with the valves. ■ Rated voltage: 500 kV DC
■ Rated current: 1800 A DC
21
22. 5.4 Harmonic Filters
The filter arrangements on the AC side of an
HVDC converter station have two main duties:
■■ to absorb harmonic currents generated
by the HVDC converter and thus to reduce
the impact of the harmonics on the connected
AC systems, like AC voltage distortion and
telephone interference
■■ to supply reactive power for compensating
the demand of the converterstation
Each filter branch can have one to three tuning
frequencies. Figure 5.4.1-1 shows different
harmonic filter types with their impedance
frequency characteristics.
5.4.1 AC Harmonic Filter
5.4.1.1 Design Criteria for AC Filters
Reactive Power Requirements
Fig. 5.4.1-2: AC filters and capacitor banks of Gezhouba/Shanghai
The reactive power consumption of an HVDC converter
depends on the active power, the transformer reactance
Single-tuned
and the control angle. It increases with increasing
active power. A common requirement to a converter
Harmonic Order station is full compensation or overcompensation
1000
Filter Impedance
at rated load. In addition, a reactive band for the
800
load and voltage range and the permitted voltage
600
400
step during bank switching must be determined.
200 These factors will determine the size and number
0 of filter and shunt capacitor banks.
0 10 20 30 40 50
Harmonic Performance Requirements
HVDC converter stations generate characteristic
Double-tuned
and non-characteristic harmonic currents. For a
Harmonic Order twelve-pulse converter, the characteristic harmonics
1000
are of the order n = (12 * k) ± 1 (k = 1,2,3 ...). These
Filter Impedance
800 are the harmonic components that are generated
600 even during ideal conditions, i.e. ideal smoothing
400 of the direct current, symmetrical AC voltages, trans-
200 former impedance and firing angles. The characteristic
0 harmonic components are the ones with the highest
0 10 20 30 40 50 current level, but other components may also be
of importance. The third harmonic, which is mainly
caused by the negative sequence component of the
Triple-tuned
AC system, will in many cases require filtering.
Harmonic Order
800 An equivalent circuit for determination of harmonic
Filter Impedance
600
performance is given in figure 5.4.1-3. The most
commonly used criteria for harmonic performance
400
are related to the harmonic voltage on the converter
200 station busbar. The purpose of the filter circuit is to
0 provide sufficiently low impedances for the relevant
0 10 20 30 40 50
harmonic components in order to reduce the harmonic
voltages to an acceptable level.
Fig. 5.4.1-1: Different harmonic filter types
22
23. There are basically two methods to include the
network impedance in the filter calculations:
■■ to calculate impedance vectors for all relevant
harmonics and grid conditions,
Ih ZF Uh ZN ■■ to assume locus area for the impedance vectors.
The modelling of a complete AC network with all its
components is very complex and time-consuming.
For this reason, the locus method is very often used.
Harmonic Filter Network It is based on a limited number of measurements
Current Impedance Impedance or calculations. Different locus areas for different
Source
harmonics or bands are often determined to give
a more precise base for the harmonic performance
Fig. 5.4.1-3: Equivalent circuit for calculation
calculation.
of harmonic voltages and currents in the AC system
A typical locus area is shown in fig. 5.4.1-4. It is
The acceptance criteria for the harmonic distortion assumed that the impedance vector will be some-
depend on local conditions and regulations. A com- where inside the perimeter of the coloured area.
monly used criterion for all harmonic components
up to the 49th order is as follows: The impedance vector of the filter is transformed
into the Y plane for each harmonic frequency.
With both the network and the filter impedances
D n Individual harmonic voltage
plotted in the admittance plane, the shortest vector
distortion of order n in percent
between the filter admittance point and the network
of the fundamental AC busbar
admittance boundary gives the lowest possible
voltage (typical limit 1%)
admittance value for the parallel combination of
the network and the filter. This value is used to
Drms Total geometric sum of
determine the highest possible harmonic voltage.
individual voltage distortion
Dn (typical limit 2 %)
The BTS Telephone Interference Factor (TIF) and the
CCITT Telephone Harmonic Form Factor (THFF) are
determined with weighted factors in order to evaluate
the voltage distortion level on the AC busbar with
respect to the expected interference level in nearby
analogue telephone systems. The IT product is a
criterion for harmonic current injected into AC over- Ymin = 1/Rmax Ymax = 1/Rmin
head lines. The criteria based on telephone inter-
ference are in many cases irrelevant, because modern
digital telephone systems are insensitive to harmonic
interference. Yf
Network Impedance Yres
The distortion level on the AC busbar depends on
the grid impedance as well as the filter impedance.
An open circuit model of the grid for all harmonics
is not on the safe side. Parallel resonance between
the filter impedance and the grid impedance may
create unacceptable amplification of harmonic com- Fig. 5.4.1-4 Circle of network admittance
ponents for which the filters are not tuned. For this and the resonance conditions
reason, an adequate impedance model of the grid
for all relevant harmonics is required in order to
optimize the filter design.
I h = Harmonic source current
Z f = Filter impedance
Z N = Network impedance
U h = Harmonic voltage
23
24. Fig. 5.4.2-1 DC filter of Guangzhou/China
The selective resonance method represents a reason- Requirements to Ratings
able compromise. It takes into consideration the fact
that the highest voltage distortion (highest harmonic Steady-State Calculation
voltage) occurs with a parallel resonance between The voltage and current stresses of AC filters consist of
filter and AC network. It is unrealistic however, to the fundamental frequency and harmonic components.
assume that such a parallel resonance takes place Their magnitudes depend on the AC system voltage,
at all frequencies. Normally it is sufficient to consider harmonic currents, operating conditions and AC system
in the calculation of total distortion and TIF value impedances. The rating calculations are carried out
only two maximum individual distortions from the in the whole range of operation to determine the
resonance calculation. The AC network is assumed highest steady-state current and voltage stresses
to be open for the remaining harmonic currents. for each individual filter component.
The filter calculations must reflect detuning caused Transient Calculation
by AC network frequency deviations and component The objective of the transient rating calculation
parameter deviations. Production tolerances, tempe- is to determine the highest transient stresses for
rature drift and failure of capacitor elements are the each component of the designed filter arrangement.
main contributors to parameter deviations. The results of the transient calculation should
contain the voltage and current stresses for each
component, energy duty for filter resistors and
arresters, and the insulation levels for each filter
component.
24
25. To calculate the highest stresses of both lightning 5.4.2.2 Design Criteria for DC Filter Circuits
and switching surge type, different circuit The interference voltage induced on the telephone
configurations and fault cases should be studied: line can be characterized by the following equation:
■■ Single-Phase Ground Fault
The fault is applied on the converter AC bus
next to the AC filter. It is assumed that the
filter capacitor is charged to a voltage level Ieq = (Hµ * Cµ * Iµ(x))2
corresponding to the switching impulse
protective level of the AC bus arrester. Vin(x) = Z * Ieq
■■ Switching Surge
For the calculation of switching surge stresses,
a standard wave of 250/2500 µs with a crest value
where
equal to the switching impulse protective level
of the AC bus arrester is applied at the AC converter
bus.
Vin(x) = Interference voltage on the
■■ Filter Energization
telephone line at point x
The AC filter is assumed to be energized at the
(in mV/km)
moment for the maximum AC bus peak voltage.
This case is decisive for the inrush currents
H µ = Weighting factors which reflect
of AC filters.
the frequency dependence of
■■ Fault Recovery after Three-Phase
the coupling between telephone
Ground Fault
and HVDC lines
Various fault-clearing parameters should be
investigated to determine the maximum energy
C µ = “C message“ – weighting factors
stresses for AC f ilter arresters and resistors.
The worst-case stresses are achieved if the
Iµ(x) = Resulting harmonic current
HVDC converters are blocked after fault initiation,
of the ordinal number µ in
while the AC filters remain connected to the
the HVDC line at point x as the
AC bus after fault clearing and recovery of the
vector sum of the currents
AC system voltage. In this case, a temporary
caused by the two HVDC stations
overvoltage with high contents of non-characteristic
harmonics will occur at the AC bus due to the
Ieq = Psophometric weighted equivalent
effects of load rejection, transformer saturation
disturbing current
and resonance between filter and AC network at
low frequency.
Z = Mutual coupling impedance
between the telephone and
5.4.2 DC Harmonic Filter
HVDC lines
5.4.2.1 DC Filter Circuits
Harmonic voltages which occur on the DC side of
a converter station cause AC currents which are The equivalent disturbing current combines
superimposed on the direct current in the trans- all harmonic currents with the aid of weighting
mission line. These alternating currents of higher factors to a single interference current. With
frequencies can create interference in neighbouring respect to telephone interference, it is the
telephone systems despite limitation by smoothing equivalent to the sum of all harmonic currents.
reactors. It also encompasses the factors which determine
the coupling between the HVDC and telephone
DC filter circuits, which are connected in parallel lines:
to the station poles, are an effective tool for com- ■■ Operating mode of the HVDC system
bating these problems. The configuration of the (bipolar or monopolar with metallic or
DC filters very strongly resembles the filters on ground return)
the AC side of the HVDC station. There are several ■■ Specific ground resistance at point x
types of filter design. Single and multiple-tuned
filters with or without the high-pass feature are The intensity of interference currents is strongly
common. One or several types of DC filter can dependent on the operating condition of the
be utilized in a converter station. HVDC. In monopolar operation, telephone
interference is significantly stronger than in
bipolar operation.
25