The ADEMCO 5802MN2 is a miniature wireless transmitter that sends signals to an alarm system when its two buttons are pressed simultaneously. It uses two lithium batteries and has a water-resistant design. The transmitter automatically sends status messages to the receiver every 70-90 minutes. It must be programmed into the alarm system with its unique serial number and loop number to be defined as a supervised or unsupervised wireless device.
Manual del dispositivo regulador oculto Z-Wave de Widom que permite variar la intensidad de una lámpara, o la velocidad de un motor (como por ejemplo un ventilador).
P700 Solid State Power Controller (SSPC) is a fully rated 150 Amperes device available for use in today\’s and tomorrow\’s Power Systems. Features reliable trouble free switching together with real short circuit
protection. Load current is sensed and shutdown initiated within microseconds.
Manual del dispositivo regulador oculto Z-Wave de Widom que permite variar la intensidad de una lámpara, o la velocidad de un motor (como por ejemplo un ventilador).
P700 Solid State Power Controller (SSPC) is a fully rated 150 Amperes device available for use in today\’s and tomorrow\’s Power Systems. Features reliable trouble free switching together with real short circuit
protection. Load current is sensed and shutdown initiated within microseconds.
Buy the Edwards Signaling 2452THS-1575-W at JMAC Supply.
https://www.jmac.com/Edwards_Signaling_2452THS_15_75_W_p/edwards-2452ths-15-fslash-75-w.htm?=slideshare
The WiDom Roller Shutter V2 is a small and compact device which can control your roller shutters, blinds, curtains, etc. Thanks to its sophisticated design the modul fits into a junction box
Buy the Edwards Signaling 2452THS-1575-W at JMAC Supply.
https://www.jmac.com/Edwards_Signaling_2452THS_15_75_W_p/edwards-2452ths-15-fslash-75-w.htm?=slideshare
The WiDom Roller Shutter V2 is a small and compact device which can control your roller shutters, blinds, curtains, etc. Thanks to its sophisticated design the modul fits into a junction box
The micromodule Zipato energy meter monitors the power consumption of two different circuits and signals to any compatible Z-Wave controller in real time.
Mini Zipato drive with energy measurement allows the variation in your interior lighting to create a pleasant atmosphere in your home and also help you to reduce your energy consumption. Actually it is able to transmit the instantaneous power consumption (W) and cumulative (KWh) of equipment attached to it.
WiDomSmartTE Dimmer is an "in-wall device" that controls the luminosity level and/or fan speed. A universal device that controls the light intensity of all types of dimmable lights, including LED lamps and energy-saving lamps. The Smart TE Dimmer includes the ON / OFF control option of non-dimmable loads
1. N8331V3 5/04 Rev. A Specifications
ADEMCO 5802MN2 Unit Dimensions:
2.75” (70mm) x 1.75” (45mm) x 0.5” (13mm)
SUPERVISED MINIATURE TRANSMITTER LED: Lights when unit transmits.
INSTALLATION AND SETUP GUIDE Battery: 3V Duracell DL2430, or Newsum, Maxell, Panasonic,
Renata, or Sanyo CR2430
The ADEMCO 5802MN is a wireless transmitter that may In UL installations: 3V Renata CR2430 only
be worn on a belt or around the neck (belt clip and To access the batteries, pry open
necklace supplied). Pressing both buttons on the the case front. In some cases,
transmitter at the same time sends a signal to the control you must first remove a small
receiver. The 5802MN2 is intended for use only with Phillips-head screw from the case
wireless alarm systems that support 5800 Series devices. back before prying open the case
front
The transmitter is supervised, i.e., it automatically sends a
5802MN2-001-V0
Note battery polarity:
message to the control receiver that includes battery REMOVE INSIDE
STACK 2 BATTERIES
NEGATIVE SIDE DOWN
+ POS end must face up (visible
status information every 70-90 minutes. FRONT COVER
when installed).
This transmitter can be programmed as any zone type REFER TO THE INSTALLATION INSTRUCTIONS FOR THE
response (e.g., Emergency Panic, Relay Action, etc.). RECEIVER/CONTROL WITH WHICH THIS DEVICE IS USED FOR
BATTERY REPLACEMENT WARRANTY INFORMATION AND FOR DETAILS REGARDING THE
LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
The 5802MN2 is powered by two long-life Lithium
batteries that may be replaced when a low battery is FCC STATEMENT
FCC ID: CFS8DL5802MN2 CANADA: 1748102611 5 3
eventually indicated by the control unit.
This device complies with Part 15 of the FCC Rules. Operation is
NOTE: Although the 5802MN2 is water-resistant, please subject to the following two conditions:
do not submerge. (1) This device may not cause harmful interference
PROGRAMMING THE SERIAL NUMBER (2) This device must accept any interference received, including
The 5802MN2 has a unique identification code (serial interference that may cause undesired operation.
number) permanently assigned during manufacture. UL US Listings: HOUSEHOLD BURGLARY WARNING SYSTEM
CONTROL UNIT ACCESSORY UL Canadian Listings: HOUSEHOLD
You must “enroll” the transmitter’s serial number and loop BURGLARY WARNING SYSTEM CONTROL UNIT ACCESSORY ALSO
number during system programming. The 5802MN2 may LISTED FOR USE AS A SIGNAL APPLIANCE, MISCELLANEOUS
be defined as Input Type “RF” (supervised RF, do not CERTIFIED FOR CANADA.
take out of range) or “UR” (Unsupervised RF). Its loop
number is “1.” See the control unit’s Installation
Instructions for further details regarding programming.
When installation is complete, verify operation from
desired location(s). ÊN8331V3QŠ
N8331V3 5/04 Rev. A