This document summarizes a research paper that proposes a high step-up boost converter using a diode-capacitor technique to improve efficiency for renewable energy applications. The converter incorporates additional voltage multiplier cells of diodes and capacitors into a conventional boost converter to increase voltage gain. Simulation results using PSIM show the converter can achieve high voltage gains with low switching losses, current ripples, and voltage stresses on components. This makes it suitable for high-performance, high-voltage renewable energy applications.

1. Proceedings of the International Conference on Emerging Trends in Engineering and Management (ICETEM14)
30-31, December, 2014, Ernakulam, India
289
HIGH STEP-UP CONVERTER WITH DIODE CAPACITOR
TECHNIQUE FOR RENEWABLE ENERGY
APPLICATIONS
ARYA RAMACHANDRAN1
, SREETHUMOL M V2
1
M.tech Student, Department of EEE, Jyothi Engineering College, Cheruthuruthy, Kerala, India
2
Assistant professor, Department of EEE, Jyothi Engineering College, Cheruthuruthy, Kerala, India
ABSTRACT
This paper presents a high step-up boost converter with diode capacitor technique. In this topology an additional
stage of voltage multiplier cells (diodes and capacitors) is incorporated into the conventional boost converter which will
increase the voltage gain and efficiency of the converter. The peculiarity of this new method is that the switching losses,
ripples and the stresses are low. Another important feature of this converter is the lower blocking voltage across the
controlled switches compared to the other existing circuits. By using the metal oxide semiconductor field effect
transistors (MOSFETs) with reduced on-resistance further minimizes the conduction losses. The simulation is done using
PSIM and the simulation results prove that the converter can be applied to high performance, high voltage applications.
Keywords: Boost Converter, High Voltage Gain, Three State Switching Cell, And Voltage Multiplier Cells.
I. INTRODUCTION
The use of fossil fuels contributes high amount of pollution which ultimately results in ozone depletion, global
warming, climatic changes etc. Thus the life on earth is affected. Therefore the renewable resources has to be exploited
which are pollution free and eco friendly. Till now there are many ways to acquire these energy sources. But they have
certain limitations since they are derived from the natural resources. Their performance can be affected by the varying
climatic conditions. Therefore we incorporate the power electronics technology to improve the efficiency of these
systems. The most popular and often used renewable energy sources are solar energy, wind, fuel cells etc. Considering
the overall cost of renewable energy system and its low output, the use of high efficiency power electronics converters is
a must. Therefore it is essential to place a boost converter at the output of the renewable energy systems. Then only this
energy can be properly utilized for high power applications. One such efficient boost converter topology is discussed
here.
The literature shows the advantages and disadvantages of many types of dc-dc step up converters. Theoretically,
the static gain of a boost converter tends to infinite when the duty cycle tends to unity. However this is not possible in
practical, because there will be conduction losses in the semiconductor devices which limit such high gain [1].
A boost converter with switched capacitors is shown in paper [2] for obtaining high voltage gain. Here the
output voltage of the converter is increased by adding capacitors. The high component count is a major drawback in this
topology. The interleaved structure is another effective solution to increase the power level [3]. Thus it can be used for
high power high voltage applications. Interleaving can minimize the current ripple and doubles the switching frequency.
The use of voltage multiplier cells can provide high voltage gain and reduce the voltage stress across the semiconductor
elements. However the high component count increases the conduction losses and snubber circuit is required due to the
reverse recovery currents through the multiplier diodes [4].The converter that is presented in [5] is based on the three
INTERNATIONAL JOURNAL OF ELECTRICAL ENGINEERING &
TECHNOLOGY (IJEET)
ISSN 0976 – 6545(Print)
ISSN 0976 – 6553(Online)
Volume 5, Issue 12, December (2014), pp. 289-294
© IAEME: www.iaeme.com/IJEET.asp
Journal Impact Factor (2014): 6.8310 (Calculated by GISI)
www.jifactor.com
IJEET
© I A E M E

2. Proceedings of the International Conference on Emerging Trends in Engineering and Management (ICETEM14)
30-31, December, 2014, Ernakulam, India
290
state switching cell along with the voltage multiplier cells. This converter can provide high voltage gain in high power
applications, the input current ripple is low, and the input inductor is designed for twice the switching frequency and the
voltage stress across the switches are low. But the main drawbacks are, a snubber circuit is necessary for each switch and
an additional winding per cell is required for the autotransformer.
Within this context this paper describes a boost converter for high voltage step-up applications with two cells
using diode capacitor technique. The duty ratio is taken greater than 0.5, duty ratio less than 0.5 can lead to poor
performance of the transformer.
II. CIRCUIT DESCRIPTION
The topology that uses the three state switching cell and voltage multiplier cells are shown in Fig. 1.
Fig.1: Boost converter using two voltage multiplier cells (mc=2)
The assumptions that are made in this topology are1) the input voltage is less than the output voltage, 2) the
behaviour of the semiconductors and magnetic components are ideal, 3) the switching frequency is constant, 4) the
autotransformer turns ratio is one, 5) the drive signal to the switches are 1800
apart and 6) the converter under steady
state operation is considered. From the Fig.1 we can see that the circuit is formed by a voltage source Vi, input inductor
L, autotransformer Tr, two controlled switches S1 and S2, the multiplier cells consists of the capacitors and diodes which
are respectively C1, C2, C3, C4, D1, D2, D3, and D4, the rectifier diodes are D5 and D6, the output capacitor C0 and the
load resistor R0. The efficiency can be increased by the use of the three state switching cells. The claimed advantages are:
the input current is continuous with low ripple; the input inductor is designed for twice the switching frequency, the
voltage stress across the switches is low, reduced weight and size of the components. Hence the use of 3SSC leads to the
use of switches with reduced current rating, which is desirable in high-power high-current applications.
An autotransformer is used to achieve high voltage conversion ratio, either in step-up or step-down applications.
The gain can be increased by adjusting the turns ratio of the transformer without affecting the voltage stress across the
main switches. But the main disadvantages are the losses caused due to increased size and weight associated with the
transformer. The use of voltage multiplier cells is not new and has already been reported in literature. For example, in [6]
employs multiplier capacitors to achieve high voltage gain. The multiplier cells are formed by the diodes and capacitors.
The charging of capacitors at regular intervals of time period associated with the turn on of the diodes is the reason for
voltage step up. The number of multiplier cells used in the converter is based on the application. The input inductor is
also designed for twice the switching frequency, implying reduction of weight and size. The voltage stress across the
switches is less than half of the output voltage. A metal oxide semiconductor field effect transistor (MOSFETs) with
reduced on-resistance is used to further minimize the conduction losses. However, the converter cannot operate
adequately when duty cycle is lower than 0.5 due to magnetic induction issues.
The study carried out in this scheme only considers the operation of the converter with duty cycle, D > 0.5. This
is a significant improvement as compared to the other topologies presented in the literature survey. The operation
of the converter with duty cycle lower than 0.5 leads to poor performance of the transformer. Thus it is not possible to
step up the output voltage to the desired value. The conduction losses are less compared to other existing boost
topologies. The specifications of the parameters are as follows:

3. Proceedings of the International Conference on Emerging Trends in Engineering and Management (ICETEM14)
30-31, December, 2014, Ernakulam, India
291
Table 1: Converter specifications
III. DESIGN
The gain Gv, of the converter is given by:
Gv =
௏బ
௏೔
=
௠௖ାଵ
ଵି஽
(1)
where, V0 is the output voltage, Vi is the input voltage, mc is the multiplier cell and D is the duty cycle.
The input inductor is designed based on the equation:
‫ܮ‬ =
ܸ଴
16݂௦(݉ܿ + 1)∆‫ܫ‬௅
(2)
where, L is the inductor, fS is the switching frequency, mc is the multiplier cell and ∆IL is the ripple current
The output current is given by:
‫݋ܫ‬ =
‫ܫ‬௜(1 − ‫)ܦ‬
(݉ܿ + 1)
(3)
where, Ii is the input current, D is the duty cycle, mc is the multiplier cell.
The expression for output capacitor is:
‫݋ܥ‬ =
‫ܫ‬ை (1 − ‫)ܦ‬
2∆ܸ௖݂௦
(4)
where, ∆ܸ௖ is the voltage ripple.
IV. ANALYSIS AND RESULTS
Fig2: PSIM model of a boost converter with diode–capacitor technique
Parameter Specifications
Input battery voltage 48 V
Output voltage 400 V
Power 1000 W
Frequency 25 kHz

4. Proceedings of the International Conference on Emerging Trends in Engineering and Management (ICETEM14)
30-31, December, 2014, Ernakulam, India
292
Fig3: Output and input voltage waveforms
Fig 4: Input inductor current waveform
Fig 5: Voltage across diode D1
Fig 6: Voltage across diode D3

5. Proceedings of the International Conference on Emerging Trends in Engineering and Management (ICETEM14)
30-31, December, 2014, Ernakulam, India
293
Fig 7: Voltage across diode D5
Fig 8: Voltage across capacitor C4
Fig 9: Voltage across capacitor C2
V. CONCLUSION
The important characteristic of the new generalized non isolated boost converter with high voltage gain is the
reduced blocking voltage across the controlled switches. The main advantages of this topology are:
Reduced size, weight and volume of the magnetic components
The current stress through the switches is low
Conduction losses are less compared to other boost topologies.

6. Proceedings of the International Conference on Emerging Trends in Engineering and Management (ICETEM14)
30-31, December, 2014, Ernakulam, India
294
REFERENCES
[1] R. A. da Camara, C. M. T. Cruz, and R. P. Torrico-Bascope (2009).Boost based on three-state switching cell
for UPS applications. in Proc. Brazilian Power Electron. Conf, 313–318.
[2] O.Abutbul, A. Gherlitz, Y. Berkovich, and A. Ioinovici (2003).Boost converter with high voltage gain using
a switched capacitor circuit. in Proc. Int. Symp. Circuits Syst, III-296–III-299.
[3] Y. Jang and M. M. Jovanovic (2007).Interleaved boost converter with intrinsic voltage-doubler characteristic
for universal-line PFC front end. IEEE Trans. Power Electron.vol.22,no.4,1394–1401.
[4] M. Prudente, L. L. Pfitscher, G. Emmendoerfer, E. F. Romaneli, and R.Gules (2008). Voltage multiplier cells
applied to non-isolated converters. IEEE Trans. Power Electron, vol. 23, no. 2, 871–887.
[5] G. V. Torrico-Bascope, R. P. TorricoBascope, D. S. Oliveira, Jr.,S. V. Araüjo, F. L. M. Antunes, and C.
G. C. Branco (2006).A high step-up converter based on three-state switching cell. IEEE Int. Symp.Ind.
Electron, 998–1003.
[6] J.-Y. Lee and S.-N. Hwang(2008). Non-isolated high-gain boost converter using voltage-stacking cell.
Electron. Lett., vol. 44, no. 10, 644–645.
[7] C. G. C. Branco, C. M. T. Cruz, R. P. Torrico-Bascope, and F. L. M. Antunes (2008). A non-isolated single-
phase UPS topology with 110-V/220-V input-output voltage ratings. IEEE Trans. Ind. Electronvol. 55, no. 8,
2974–2983
[8] Elmokhtar. A. Elhamruni and Dr. A. K. Bhardwaj, “Analysis and Design Resonant Converter as Constant
Current Source For Capacitor Charging” International Journal of Electrical Engineering & Technology
(IJEET), Volume 5, Issue 7, 2014, pp. 25 - 31, ISSN Print : 0976-6545, ISSN Online: 0976-6553.