Groschopp 05136 specsheet
•
0 likes•19 views
The document provides specifications for an AC 3 Phase 6540 TEFC motor with a voltage of 230V and speed of 1570 rpm. The motor has a rating of 1569.7 rpm and 1.4 lb-in of torque drawing 0.31 amps of current and producing 27 watts of output power equivalent to 0.0357 HP. The motor has a continuous duty cycle with peak efficiency of 34.4% and can produce up to 2.51 lb-in of torque when starting or stalling, drawing 0.59 amps of current. Performance charts show torque and efficiency at varying speeds. The motor is sold and serviced by Electromate.
Report
Share
Report
Share
Download to read offline
Recommended
Groschopp 05137 specsheet
The document provides specifications for an AC 3 Phase 6540 TENV motor with a rating of 1563.8 rpm and 1.2lb-in of torque consuming 0.25 amps of current. The motor produces 23 watts of output power and 0.0304 HP. Under cold conditions, the motor reaches 948.42 rpm with 2.64 lb-in of torque and stalls at 0 rpm with 2.39lb-in of torque. The motor, gearbox, and system efficiencies are listed as 37.8% and it can operate continuously under any load conditions.
Groschopp 05128 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 230V, speed of 1490 rpm, and no gearbox. Key specifications include a rating of 1493.1 rpm and 1.0 lb-in of torque drawing 0.33 amps of current. Performance tests found a breakdown speed of 1015.34 rpm and pullup speed of 0 rpm. The motor has a continuous duty cycle and system efficiency of 28.6%. Startup requires 0.43 amps and produces 1.27 lb-in of torque. A graph shows efficiency decreases with increasing torque from 90% at 0 rpm to 20% at 1600 rpm.
Groschopp 05134 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 230V, speed of 2910 rpm, and no gearbox. Key specifications include a rated speed of 2905.9 rpm, torque of 1.5 lb-in, current of 0.49 amps, output power of 50 watts, and efficiency of 47.2%. Startup conditions include a current of 0.96 amps and torque of 1.37 lb-in. A graph shows efficiency and speed at varying torque levels from 0 to 3200 rpm.
Groschopp 05138 specsheet
This document provides specifications for an AC 3 Phase 6540 TEFC motor with a voltage of 230V, speed of 3110 rpm, and no gearbox. Key specifications include a rating of 3107.9 rpm and 0.1117 HP at 55.7% efficiency. Performance charts show speed, torque, current and efficiency at varying loads from start up to full speed.
Groschopp 05152 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 230V, 50Hz, and speed of 2430rpm. The motor has a rating of 2425.3rpm and 1.5lb-in of torque while drawing 0.47amps and producing 42watts and 0.0560HP of output. Breakdown and pullup tests were also performed. Efficiency is listed for various torque levels. The motor is intended for continuous duty and has a startup current of 0.82amps and stall torque of 1.40lb-in. Contact information is provided for the distributor Electromate.
Groschopp 05156 specsheet
This document provides specifications for an AC 3 Phase 6540 TEFC motor with a voltage of 230V, frequency of 50Hz, and speed of 1250rpm without a gearbox. Key specifications include a rated speed of 1245rpm, startup current of 0.52amps, and maximum torque of 3.3lb-in. The motor has a continuous duty cycle and peak efficiency of 33.4% at nominal operating speeds and torques. Performance curves show efficiency decreases and torque increases at lower speeds.
Groschopp 05159 specsheet
This document provides specifications for an AC 3 Phase 6540 TENV motor with a voltage of 230V, frequency of 50Hz, and speed of 2710rpm without a gearbox. Key specifications include a rating of 2710rpm and 1.5lb-in of torque at 0.34amps and 48watts of output, or 0.0645HP. Breakdown and pullup torque and speed are also listed, along with duty cycle, efficiency curves, and start/stall conditions. The motor is sold and serviced by Electromate.
Groschopp 05122 specsheet
This document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 115V, speed of 1490 rpm, and no gearbox. Key specifications include a rated speed of 1491.8 rpm, torque of 1.0 lb-in, current of 0.49 amps, output power of 17 watts, and output horsepower of 0.0227 HP. The motor has a breakdown speed of 1024.29 rpm, pullup torque of 1.06 lb-in, and continuous duty cycle. Start/stall conditions are a current of 0.71 amps and torque of 1.06 lb-in. A graph shows efficiency levels between 0-1600 rpm.
Recommended
Groschopp 05137 specsheet
The document provides specifications for an AC 3 Phase 6540 TENV motor with a rating of 1563.8 rpm and 1.2lb-in of torque consuming 0.25 amps of current. The motor produces 23 watts of output power and 0.0304 HP. Under cold conditions, the motor reaches 948.42 rpm with 2.64 lb-in of torque and stalls at 0 rpm with 2.39lb-in of torque. The motor, gearbox, and system efficiencies are listed as 37.8% and it can operate continuously under any load conditions.
Groschopp 05128 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 230V, speed of 1490 rpm, and no gearbox. Key specifications include a rating of 1493.1 rpm and 1.0 lb-in of torque drawing 0.33 amps of current. Performance tests found a breakdown speed of 1015.34 rpm and pullup speed of 0 rpm. The motor has a continuous duty cycle and system efficiency of 28.6%. Startup requires 0.43 amps and produces 1.27 lb-in of torque. A graph shows efficiency decreases with increasing torque from 90% at 0 rpm to 20% at 1600 rpm.
Groschopp 05134 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 230V, speed of 2910 rpm, and no gearbox. Key specifications include a rated speed of 2905.9 rpm, torque of 1.5 lb-in, current of 0.49 amps, output power of 50 watts, and efficiency of 47.2%. Startup conditions include a current of 0.96 amps and torque of 1.37 lb-in. A graph shows efficiency and speed at varying torque levels from 0 to 3200 rpm.
Groschopp 05138 specsheet
This document provides specifications for an AC 3 Phase 6540 TEFC motor with a voltage of 230V, speed of 3110 rpm, and no gearbox. Key specifications include a rating of 3107.9 rpm and 0.1117 HP at 55.7% efficiency. Performance charts show speed, torque, current and efficiency at varying loads from start up to full speed.
Groschopp 05152 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 230V, 50Hz, and speed of 2430rpm. The motor has a rating of 2425.3rpm and 1.5lb-in of torque while drawing 0.47amps and producing 42watts and 0.0560HP of output. Breakdown and pullup tests were also performed. Efficiency is listed for various torque levels. The motor is intended for continuous duty and has a startup current of 0.82amps and stall torque of 1.40lb-in. Contact information is provided for the distributor Electromate.
Groschopp 05156 specsheet
This document provides specifications for an AC 3 Phase 6540 TEFC motor with a voltage of 230V, frequency of 50Hz, and speed of 1250rpm without a gearbox. Key specifications include a rated speed of 1245rpm, startup current of 0.52amps, and maximum torque of 3.3lb-in. The motor has a continuous duty cycle and peak efficiency of 33.4% at nominal operating speeds and torques. Performance curves show efficiency decreases and torque increases at lower speeds.
Groschopp 05159 specsheet
This document provides specifications for an AC 3 Phase 6540 TENV motor with a voltage of 230V, frequency of 50Hz, and speed of 2710rpm without a gearbox. Key specifications include a rating of 2710rpm and 1.5lb-in of torque at 0.34amps and 48watts of output, or 0.0645HP. Breakdown and pullup torque and speed are also listed, along with duty cycle, efficiency curves, and start/stall conditions. The motor is sold and serviced by Electromate.
Groschopp 05122 specsheet
This document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 115V, speed of 1490 rpm, and no gearbox. Key specifications include a rated speed of 1491.8 rpm, torque of 1.0 lb-in, current of 0.49 amps, output power of 17 watts, and output horsepower of 0.0227 HP. The motor has a breakdown speed of 1024.29 rpm, pullup torque of 1.06 lb-in, and continuous duty cycle. Start/stall conditions are a current of 0.71 amps and torque of 1.06 lb-in. A graph shows efficiency levels between 0-1600 rpm.
Groschopp 05124 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor that operates at 115v and 60Hz with a speed of 2990 rpm. The motor has an output of 53 watts, 0.0717 HP, and a torque of 1.5lb-in at its rated speed of 2988.9 rpm. Charts show its torque and efficiency characteristics at different speeds when cold and hot.
Groschopp 05132 specsheet
The document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 230V, frequency of 60Hz, and speed of 3100rpm. Key specifications include a rating of 3100.8rpm at 1.0lb-in of torque drawing 0.38amps, with an output of 38watts and 0.0513HP. Startup current is 0.78amps with 0.75lb-in of torque. Efficiency is provided in a graph showing the relationship between speed, torque, and efficiency for both cold and hot operating conditions. The motor has a 4uF 440V capacitor and is sold and serviced by Electromate.
Groschopp 05157 specsheet
This document provides specifications for an AC 3 Phase 6540 TENV motor with a rating of 1207.1 rpm and 1.5 lb-in of torque consuming 0.23 amps of current. The motor produces 21 watts of output power equivalent to 0.0279 horsepower. Under breakdown and pullup conditions, the motor reaches lower speeds and higher torques. The motor has a continuous duty cycle with peak efficiencies of 36% for the gearbox, motor, and overall system. It produces higher current and torque under start or stall conditions. A graph shows efficiency decreases with increasing torque from a peak of 90% at lower torques.
Groschopp 05126 specsheet
The document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 115V, speed of 3150 rpm, and no gearbox. Key specifications include a rating of 3152.3 rpm and 1.1 lb-in of torque at 0.69 amps and 41 watts of output. The motor has a breakdown speed of 2462.14 rpm and pullup speed of 0 rpm. It has a continuous duty cycle and system efficiency of 52.6%. Start/stall conditions are 1.58 amps and 0.93 lb-in of torque. Performance charts show efficiency and torque curves versus speed in both cold and hot conditions.
Groschopp 05120 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 115V, speed of 1480 rpm, and no gearbox. Key specifications include a rated speed of 1483 rpm, torque of 1.1 lb-in, current of 0.64 amps, output of 20 watts, and efficiency of 30.6%. Performance data is provided showing torque and speed curves for cold and hot operation.
Groschopp 05158 specsheet
This document provides specifications for an AC 3 Phase 6540 TEFC motor with a voltage of 230V, frequency of 50Hz, and speed of 2540rpm without a gearbox. Key specifications include a rated speed of 2535.5rpm, torque of 2.4lb-in, current of 0.49amps, output of 73watts and 0.0977HP. Breakdown and pullup torque and speed are also listed along with duty cycle, efficiency and start/stall conditions. A graph shows efficiency at varying torques and speeds for cold and hot operation. The motor is sold and serviced by Electromate.
The Back Of The Napkin
This document summarizes key aspects of visual thinking and problem solving presented in the book "The Back of the NAPKIN" by Dan Roam. It outlines the visual thinking process, tools for visual representation including charts, maps, timelines and flow charts. It also discusses frameworks for showing such as using simple, quality, vision, delta, and individual representations. The document concludes by providing information about the China Institute for Innovation, a consulting organization that helps companies and organizations improve innovation.
Setting your sites on a New Self
The document provides a guide for setting goals to develop a new self, with 6 steps: 1) Identify 2-3 big life goals, 2) Identify sub-goals for each big goal, 3) Note what inspires you, 4) Identify benefits of learning new skills, 5) Make a promise to yourself, and 6) Post your vision where you can see it daily. The goal is to help the reader anchor their experience and vision through writing exercises.
N'SKIPER
This short document promotes creating presentations using Haiku Deck, a tool for making slideshows. It encourages the reader to get started making their own Haiku Deck presentation and sharing it on SlideShare. In just one sentence, it pitches the idea of using Haiku Deck to easily design slideshows.
Fuehrungskraftentwicklung
Führungskräfte benötigen eine starke innere Haltung um gut Führen zu können. Das Wissen über die Systemgesetze ermöglicht es den Führungskräften klare Ursachen für Konflikte und Unstimmigkeiten zu erkennen. In der Führungskräfteentwicklung geht es darum, dass Wissen über Systemgesetze in die Praxis umzusetzen.
Frt - 111122 - iak verzekeringen - insure the future def-04-11-2011
Presentatie IAK Verzekeringen t.b.v. Flevum RoundTable bijeenkomst 22 november 2011.
A Software guy's ongoing journey of automation in Azure
The document discusses the benefits of meditation for reducing stress and anxiety. Regular meditation practice can help calm the mind and body by lowering heart rate and blood pressure. Making meditation a part of a daily routine, even if just 10-15 minutes per day, can offer significant health benefits over time such as improved focus, better sleep, and a more positive outlook.
Gab Abramowitz_The e-MAST data-model interface
The document discusses the e-MAST data-model interface and the Protocol for the Analysis of the Land Surface (PALS) data portal. PALS aims to bridge the observation and modeling communities by hosting standardized model experiments that include multiple observational data streams for model evaluation and development. It addresses issues like data formatting and access that have hindered interaction between the communities. PALS currently has around 140 users conducting site-based experiments and is working to expand to larger-scale distributed experiments to further evaluation of land surface, hydrological and ecosystem models.
Fex 161122 - emcm 2.0 re-design organisatie van traditioneel naar value str...
EMCM 2.0 RE-DESIGN ORGANISATIE
VAN TRADITIONEEL NAAR VALUE-STREAM STRUCTUUR
Groei en ontwikkelingen binnen EMCM hebben het management eind 2014 doen besluiten om meer focus aan te brengen in de strategie van de organisatie. De doelstelling daarbij was om van EMCM een contract manufacturing organisatie te maken, waarin Operational Excellence en Lean de sleutelwoorden zijn.
Dit heeft geleidt tot een aantal ingrijpende beslissingen met verstrekkende gevolgen voor de totale organisatie. Zo is het schoonmaken van humaan (bot)weefsel buiten de organisatie geplaatst en is EMCM zich (nog) meer gaan richten op LSG+P (Liquid, Suspension, Gels & Powders) als haar core business.
AANPAK
Werkprocessen zijn door middel van Brown Paper Sessies onder de loep genomen en knelpunten volgens de DMAIC-aanpak gedefinieerd (DMAIC = Define, Measure, Analzye, Improve and Control) om vervolgens verbetervoorstellen uit te werken en deze te implementeren. Hierbij bleek al snel dat veel oplossingen ‘afdelingsoverstijgend’ waren en dat daardoor voor het optimale resultaat een herstructurering van de organisatie noodzakelijk was.
RESULTAAT
Tijdens deze bijeenkomst zal Gert Wentzel u meenemen in het gehele veranderingsproces dat EMCM heeft afgelegd, de valkuilen, de emoties en leermomenten, als ook de nog te verwachten obstakels, zullen tijdens de bijeenkomst worden toegelicht. Tijdens deze interactie bijeenkomst krijgt u volop gelegenheid om uw vragen te stellen en/of om uw visie/suggesties te geven.
Kortom het thema en de bijzondere aard van EMCM bevatten alle ingrediënten voor een boeiende, leerzame en inspirerende bijeenkomst binnen een innovatieve omgeving.
Practica 4 determinacion de microestructura
La práctica consistió en analizar dos materiales desconocidos utilizando metalografía. Los materiales fueron lijados, pulidos y examinados con un microscopio metalográfico, determinándose que eran aluminio. El proceso incluyó lijado con papel de grano fino, pulido, ataque químico y análisis de la microestructura para identificar los materiales.
Practica 2 determinación de la resistencia mecánica a la tracción de los mate...
Practica 2 determinación de la resistencia mecánica a la tracción de los mate...Juan Andrés Castro Montoya
Este documento describe un experimento realizado en el laboratorio de ciencias de materiales para determinar la resistencia mecánica a la tracción de diferentes materiales como el aluminio, acero y neopreno. Se utilizaron dos máquinas de ensayo universal para aplicar fuerzas de tracción a las probetas de cada material a diferentes velocidades y medir la resistencia y elongación. Los resultados mostraron que los metales tienen mayor resistencia que el neopreno y que la velocidad afecta la elongación de las probetas de neopreno.Tanda awal kehamilan anak ke 2
Dokumen tersebut memberikan informasi mengenai tanda-tanda awal kehamilan yang dapat dirasakan wanita, seperti terlambat datang bulan, nyeri payudara, mual, dan perubahan selera makan. Tanda-tanda tersebut muncul akibat adanya perubahan hormon selama kehamilan awal. Wanita disarankan melakukan tes kehamilan jika curiga tengah hamil berdasarkan gejala-gejala tersebut.
Helen Cleugh_Near-real-time measurement of carbon dioxide, water and energy f...
This document discusses using flux tower and other observational data to constrain land surface models and determine carbon and water budgets across Australia. It describes how the OzFlux network provides carbon dioxide and water flux measurements from different ecosystems. These flux measurements have been used to test and improve land surface models and reduce uncertainty in estimates of net primary production for Australia. Integrating these observational constraints into the BIOS2 modeling framework has provided insights into Australia's dynamic carbon and water cycles at continental scales.
Richard Thackway_A system for tracking anthropogenic changes in condition of ...
Richard Thackway developed the VAST-2 system for tracking anthropogenic changes in the condition of Australia's plant communities over time. VAST-2 uses a framework of 22 diagnostic attributes across 10 attribute groups and 3 condition components (regenerative capacity, vegetation structure, and species composition) to document changes at sites relative to pre-European reference states. Case studies applying VAST-2 show changes in vegetation condition associated with various land uses and management practices over historical time periods. VAST-2 engages collaborators to synthesize information on vegetation transformations and supports reporting on progress toward vegetation condition targets.
Telling a Picutre Story - The Vicissitudes of Human Life in Symbols
The document tells a picture story through a series of images depicting the life cycle of a family from procreation to old age and death. It shows a man and woman uniting and having children, forming a family. It then shows friendship between men, men quarreling and fighting, a man dying, leaving his widow and children. One child dies, leaving the forlorn mother with her remaining child. Finally, the mother dies leaving one surviving child to carry on the family line into the next generation. The epilogue provides a timeline of discoveries related to microscopy and genetics from the 5th century to the 21st century.
More Related Content
What's hot
Groschopp 05124 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor that operates at 115v and 60Hz with a speed of 2990 rpm. The motor has an output of 53 watts, 0.0717 HP, and a torque of 1.5lb-in at its rated speed of 2988.9 rpm. Charts show its torque and efficiency characteristics at different speeds when cold and hot.
Groschopp 05132 specsheet
The document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 230V, frequency of 60Hz, and speed of 3100rpm. Key specifications include a rating of 3100.8rpm at 1.0lb-in of torque drawing 0.38amps, with an output of 38watts and 0.0513HP. Startup current is 0.78amps with 0.75lb-in of torque. Efficiency is provided in a graph showing the relationship between speed, torque, and efficiency for both cold and hot operating conditions. The motor has a 4uF 440V capacitor and is sold and serviced by Electromate.
Groschopp 05157 specsheet
This document provides specifications for an AC 3 Phase 6540 TENV motor with a rating of 1207.1 rpm and 1.5 lb-in of torque consuming 0.23 amps of current. The motor produces 21 watts of output power equivalent to 0.0279 horsepower. Under breakdown and pullup conditions, the motor reaches lower speeds and higher torques. The motor has a continuous duty cycle with peak efficiencies of 36% for the gearbox, motor, and overall system. It produces higher current and torque under start or stall conditions. A graph shows efficiency decreases with increasing torque from a peak of 90% at lower torques.
Groschopp 05126 specsheet
The document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 115V, speed of 3150 rpm, and no gearbox. Key specifications include a rating of 3152.3 rpm and 1.1 lb-in of torque at 0.69 amps and 41 watts of output. The motor has a breakdown speed of 2462.14 rpm and pullup speed of 0 rpm. It has a continuous duty cycle and system efficiency of 52.6%. Start/stall conditions are 1.58 amps and 0.93 lb-in of torque. Performance charts show efficiency and torque curves versus speed in both cold and hot conditions.
Groschopp 05120 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 115V, speed of 1480 rpm, and no gearbox. Key specifications include a rated speed of 1483 rpm, torque of 1.1 lb-in, current of 0.64 amps, output of 20 watts, and efficiency of 30.6%. Performance data is provided showing torque and speed curves for cold and hot operation.
Groschopp 05158 specsheet
This document provides specifications for an AC 3 Phase 6540 TEFC motor with a voltage of 230V, frequency of 50Hz, and speed of 2540rpm without a gearbox. Key specifications include a rated speed of 2535.5rpm, torque of 2.4lb-in, current of 0.49amps, output of 73watts and 0.0977HP. Breakdown and pullup torque and speed are also listed along with duty cycle, efficiency and start/stall conditions. A graph shows efficiency at varying torques and speeds for cold and hot operation. The motor is sold and serviced by Electromate.
What's hot (6)
Viewers also liked
The Back Of The Napkin
This document summarizes key aspects of visual thinking and problem solving presented in the book "The Back of the NAPKIN" by Dan Roam. It outlines the visual thinking process, tools for visual representation including charts, maps, timelines and flow charts. It also discusses frameworks for showing such as using simple, quality, vision, delta, and individual representations. The document concludes by providing information about the China Institute for Innovation, a consulting organization that helps companies and organizations improve innovation.
Setting your sites on a New Self
The document provides a guide for setting goals to develop a new self, with 6 steps: 1) Identify 2-3 big life goals, 2) Identify sub-goals for each big goal, 3) Note what inspires you, 4) Identify benefits of learning new skills, 5) Make a promise to yourself, and 6) Post your vision where you can see it daily. The goal is to help the reader anchor their experience and vision through writing exercises.
N'SKIPER
This short document promotes creating presentations using Haiku Deck, a tool for making slideshows. It encourages the reader to get started making their own Haiku Deck presentation and sharing it on SlideShare. In just one sentence, it pitches the idea of using Haiku Deck to easily design slideshows.
Fuehrungskraftentwicklung
Führungskräfte benötigen eine starke innere Haltung um gut Führen zu können. Das Wissen über die Systemgesetze ermöglicht es den Führungskräften klare Ursachen für Konflikte und Unstimmigkeiten zu erkennen. In der Führungskräfteentwicklung geht es darum, dass Wissen über Systemgesetze in die Praxis umzusetzen.
Frt - 111122 - iak verzekeringen - insure the future def-04-11-2011
Presentatie IAK Verzekeringen t.b.v. Flevum RoundTable bijeenkomst 22 november 2011.
A Software guy's ongoing journey of automation in Azure
The document discusses the benefits of meditation for reducing stress and anxiety. Regular meditation practice can help calm the mind and body by lowering heart rate and blood pressure. Making meditation a part of a daily routine, even if just 10-15 minutes per day, can offer significant health benefits over time such as improved focus, better sleep, and a more positive outlook.
Gab Abramowitz_The e-MAST data-model interface
The document discusses the e-MAST data-model interface and the Protocol for the Analysis of the Land Surface (PALS) data portal. PALS aims to bridge the observation and modeling communities by hosting standardized model experiments that include multiple observational data streams for model evaluation and development. It addresses issues like data formatting and access that have hindered interaction between the communities. PALS currently has around 140 users conducting site-based experiments and is working to expand to larger-scale distributed experiments to further evaluation of land surface, hydrological and ecosystem models.
Fex 161122 - emcm 2.0 re-design organisatie van traditioneel naar value str...
EMCM 2.0 RE-DESIGN ORGANISATIE
VAN TRADITIONEEL NAAR VALUE-STREAM STRUCTUUR
Groei en ontwikkelingen binnen EMCM hebben het management eind 2014 doen besluiten om meer focus aan te brengen in de strategie van de organisatie. De doelstelling daarbij was om van EMCM een contract manufacturing organisatie te maken, waarin Operational Excellence en Lean de sleutelwoorden zijn.
Dit heeft geleidt tot een aantal ingrijpende beslissingen met verstrekkende gevolgen voor de totale organisatie. Zo is het schoonmaken van humaan (bot)weefsel buiten de organisatie geplaatst en is EMCM zich (nog) meer gaan richten op LSG+P (Liquid, Suspension, Gels & Powders) als haar core business.
AANPAK
Werkprocessen zijn door middel van Brown Paper Sessies onder de loep genomen en knelpunten volgens de DMAIC-aanpak gedefinieerd (DMAIC = Define, Measure, Analzye, Improve and Control) om vervolgens verbetervoorstellen uit te werken en deze te implementeren. Hierbij bleek al snel dat veel oplossingen ‘afdelingsoverstijgend’ waren en dat daardoor voor het optimale resultaat een herstructurering van de organisatie noodzakelijk was.
RESULTAAT
Tijdens deze bijeenkomst zal Gert Wentzel u meenemen in het gehele veranderingsproces dat EMCM heeft afgelegd, de valkuilen, de emoties en leermomenten, als ook de nog te verwachten obstakels, zullen tijdens de bijeenkomst worden toegelicht. Tijdens deze interactie bijeenkomst krijgt u volop gelegenheid om uw vragen te stellen en/of om uw visie/suggesties te geven.
Kortom het thema en de bijzondere aard van EMCM bevatten alle ingrediënten voor een boeiende, leerzame en inspirerende bijeenkomst binnen een innovatieve omgeving.
Practica 4 determinacion de microestructura
La práctica consistió en analizar dos materiales desconocidos utilizando metalografía. Los materiales fueron lijados, pulidos y examinados con un microscopio metalográfico, determinándose que eran aluminio. El proceso incluyó lijado con papel de grano fino, pulido, ataque químico y análisis de la microestructura para identificar los materiales.
Practica 2 determinación de la resistencia mecánica a la tracción de los mate...
Practica 2 determinación de la resistencia mecánica a la tracción de los mate...Juan Andrés Castro Montoya
Este documento describe un experimento realizado en el laboratorio de ciencias de materiales para determinar la resistencia mecánica a la tracción de diferentes materiales como el aluminio, acero y neopreno. Se utilizaron dos máquinas de ensayo universal para aplicar fuerzas de tracción a las probetas de cada material a diferentes velocidades y medir la resistencia y elongación. Los resultados mostraron que los metales tienen mayor resistencia que el neopreno y que la velocidad afecta la elongación de las probetas de neopreno.Tanda awal kehamilan anak ke 2
Dokumen tersebut memberikan informasi mengenai tanda-tanda awal kehamilan yang dapat dirasakan wanita, seperti terlambat datang bulan, nyeri payudara, mual, dan perubahan selera makan. Tanda-tanda tersebut muncul akibat adanya perubahan hormon selama kehamilan awal. Wanita disarankan melakukan tes kehamilan jika curiga tengah hamil berdasarkan gejala-gejala tersebut.
Helen Cleugh_Near-real-time measurement of carbon dioxide, water and energy f...
This document discusses using flux tower and other observational data to constrain land surface models and determine carbon and water budgets across Australia. It describes how the OzFlux network provides carbon dioxide and water flux measurements from different ecosystems. These flux measurements have been used to test and improve land surface models and reduce uncertainty in estimates of net primary production for Australia. Integrating these observational constraints into the BIOS2 modeling framework has provided insights into Australia's dynamic carbon and water cycles at continental scales.
Richard Thackway_A system for tracking anthropogenic changes in condition of ...
Richard Thackway developed the VAST-2 system for tracking anthropogenic changes in the condition of Australia's plant communities over time. VAST-2 uses a framework of 22 diagnostic attributes across 10 attribute groups and 3 condition components (regenerative capacity, vegetation structure, and species composition) to document changes at sites relative to pre-European reference states. Case studies applying VAST-2 show changes in vegetation condition associated with various land uses and management practices over historical time periods. VAST-2 engages collaborators to synthesize information on vegetation transformations and supports reporting on progress toward vegetation condition targets.
Telling a Picutre Story - The Vicissitudes of Human Life in Symbols
The document tells a picture story through a series of images depicting the life cycle of a family from procreation to old age and death. It shows a man and woman uniting and having children, forming a family. It then shows friendship between men, men quarreling and fighting, a man dying, leaving his widow and children. One child dies, leaving the forlorn mother with her remaining child. Finally, the mother dies leaving one surviving child to carry on the family line into the next generation. The epilogue provides a timeline of discoveries related to microscopy and genetics from the 5th century to the 21st century.
ACEF: Australian Coastal Ecosystems Facility
The presentation provides an overview of services offered by ACEF. The presentation was part of the Workshop on Approaches to Terrestrial Ecosystem Data Management : from collection to synthesis and beyond which was held on 9th of March 2016 in University of Queensland.
Analisis berita
Udar Pristono kembali ditetapkan sebagai tersangka korupsi pengadaan bus gandeng Transjakarta senilai Rp150 miliar. Sebelumnya ia sudah menjadi tersangka kasus mark up pengadaan bus dan peremajaan bus tahun 2013 senilai Rp1,5 triliun. Korupsi di Indonesia sudah memperhatinkan dan dapat memengaruhi pandangan masyarakat menjadi apatis terhadap pemimpin serta berubahnya perasaan menjadi marah atau ke
ASDECO Project
MONITORING AND DECISION SUPPORT SYSTEMS FOR IMPACT MINIMIZATION OF DESALINATION PLANT OUTFALL IN MARINE ECOSYSTEMS
Workflow Management Software with IBM Lotus Notes, Business Process Managemen...
Workflow Management Software with IBM Lotus Notes, Business Process Managemen...GBS PAVONE Groupware GmbH
Workflow Management Software, Business Process Management Software, Integrated Project and Business Process ManagementViewers also liked (20)
Frt - 111122 - iak verzekeringen - insure the future def-04-11-2011
Frt - 111122 - iak verzekeringen - insure the future def-04-11-2011
A Software guy's ongoing journey of automation in Azure
A Software guy's ongoing journey of automation in Azure
Fex 161122 - emcm 2.0 re-design organisatie van traditioneel naar value str...
Fex 161122 - emcm 2.0 re-design organisatie van traditioneel naar value str...
Practica 2 determinación de la resistencia mecánica a la tracción de los mate...
Practica 2 determinación de la resistencia mecánica a la tracción de los mate...
Presentatie Marten Kroese 8 juni case inkoopproces vincent van gogh voor gees...
Presentatie Marten Kroese 8 juni case inkoopproces vincent van gogh voor gees...
Helen Cleugh_Near-real-time measurement of carbon dioxide, water and energy f...
Helen Cleugh_Near-real-time measurement of carbon dioxide, water and energy f...
Richard Thackway_A system for tracking anthropogenic changes in condition of ...
Richard Thackway_A system for tracking anthropogenic changes in condition of ...
Telling a Picutre Story - The Vicissitudes of Human Life in Symbols
Telling a Picutre Story - The Vicissitudes of Human Life in Symbols
Workflow Management Software with IBM Lotus Notes, Business Process Managemen...
Workflow Management Software with IBM Lotus Notes, Business Process Managemen...
Similar to Groschopp 05136 specsheet
Groschopp 05137 specsheet
The document provides specifications for an AC 3 Phase 6540 TENV motor with a rating of 1563.8 rpm and 1.2lb-in of torque consuming 0.25 amps of current. The motor produces 23 watts of output power and 0.0304 HP. Under cold conditions, the motor reaches 948.42 rpm with 2.64 lb-in of torque and stalls at 0 rpm with 2.39lb-in of torque. The motor, gearbox, and system efficiencies are listed as 37.8% and it can operate continuously under start/stall conditions of 0.52 amps and 2.39 lb-in of torque.
Groschopp 05138 specsheet
This document provides specifications for an AC 3 Phase 6540 TEFC motor with a voltage of 230V, speed of 3110 rpm, and no gearbox. Key specifications include a rating of 3107.9 rpm at 2.3 lb-in of torque drawing 0.50 amps of current. Breakdown and pullup tests were also performed. Efficiency is listed as 55.7% for the motor and system. Start/stall conditions draw 1.40 amps at 3.97 lb-in of torque. A graph shows efficiency and speed curves versus torque. The motor is sold and serviced by Electromate.
Groschopp 05159 specsheet
This document provides specifications for an AC 3 Phase 6540 TENV motor with a voltage of 230V, frequency of 50Hz, and speed of 2710rpm without a gearbox. Key specifications include a rating of 2710rpm and 1.5lb-in of torque at 0.34amps and 48watts of output, or 0.0645HP. Breakdown and pullup torque and speed are also listed, along with duty cycle, efficiency ratings, start/stall conditions, and a graph of torque vs speed and efficiency when cold and hot. The motor is sold and serviced by Electromate.
Groschopp 05158 specsheet
This document provides specifications for an AC 3 Phase 6540 TEFC motor with a voltage of 230V, frequency of 50Hz, and speed of 2540rpm without a gearbox. Key specifications include a rated speed of 2535.5rpm, torque of 2.4lb-in, current of 0.49amps, output of 73watts and 0.0977HP. Breakdown and pullup torque and speed are also listed along with duty cycle, efficiency curves, and start/stall conditions. The motor is sold and serviced by Electromate.
Groschopp 05154 specsheet
This document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 230V, 50Hz, and speed of 2580 rpm. Key specifications include a rating of 2582.3 rpm and 1.0 lb-in of torque at 0.33 amps of current and 32 watts of output power. Charts show torque and efficiency curves for the motor when cold and hot.
Groschopp 05154 specsheet
This document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 230V, 50Hz, and speed of 2580 rpm. Key specifications include a rating of 2582.3 rpm and 1.0 lb-in of torque at 0.33 amps and 32 watts of output. Breakdown and pullup tests were also performed. The motor has a continuous duty cycle and system efficiency of 47.6%. Start/stall conditions are 0.66 amps and 0.83 lb-in of torque. A graph shows efficiency versus torque from 0-2700 rpm. Notes indicate a 4uF 440V capacitor. The motor is sold and serviced by Electromate.
Groschopp 05157 specsheet
This document provides specifications for an AC 3 Phase 6540 TENV motor with a rating of 1207.1 rpm and 1.5 lb-in of torque consuming 0.23 amps of current. The motor produces 21 watts of output power equivalent to 0.0279 horsepower. Under breakdown and pullup conditions, the motor reaches lower speeds and higher torques. The motor has a continuous duty cycle with peak efficiencies of 36% for the gearbox, motor, and overall system. Startup requires 0.40 amps of current producing 2.55 lb-in of torque. A graph shows efficiency decreases with speed above 750 rpm.
Groschopp 05134 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 230V, speed of 2910 rpm, and no gearbox. Key specifications include a rated speed of 2905.9 rpm, torque of 1.5 lb-in, current of 0.49 amps, output power of 50 watts, and efficiency of 47.2%. Startup conditions include a current of 0.96 amps and torque of 1.37 lb-in. A graph shows efficiency and speed at varying torque levels from 0 to 3200 rpm.
Groschopp 05130 specsheet
This document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 230V, speed of 1500 rpm, output of 15 watts, and efficiency of 31.4%. The motor draws 0.25 amps of current at full speed of 1495.5 rpm and generates 0.8 lb-in of torque. Charts show the motor's speed and torque characteristics when cold and hot, with torque ranging from 0 to 1.4 lb-in over 0 to 1800 rpm.
Groschopp 05130 specsheet
This document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 230V, speed of 1500 rpm, output of 15 watts, and efficiency of 31.4%. The motor draws 0.25 amps of current at full speed of 1495.5 rpm and generates 0.8 lb-in of torque. Charts show its torque and efficiency characteristics at different speeds both when cold and hot.
Groschopp 05128 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 230V, speed of 1490 rpm, and output of 18 watts. Key specifications include a rating of 1493.1 rpm and 1.0 lb-in of torque at 0.33 amps of current. The motor has a breakdown speed of 1015.34 rpm and pullup torque of 1.27lb-in. It has a continuous duty cycle and system efficiency of 28.6%. Start/stall conditions are 0.43 amps and 1.27 lb-in of torque. A graph shows efficiency versus torque from 0 to 1600 rpm. It is sold and serviced by Electromate.
Groschopp 05306 specsheet
This document provides specifications for an AC 1 Ph 8040 TEFC motor with a voltage of 115V, speed of 2910 rpm, and no gearbox. Key specifications include a rated speed of 2907.9 rpm, torque of 3.1 lb-in, current of 1.88 amps, output power of 107 watts, and efficiency of 50.9%. Startup conditions include a current of 3.18 amps and torque of 3.04 lb-in. A graph shows efficiency and speed curves versus torque.
Groschopp 05306 specsheet
This document provides specifications for an AC 1 Ph 8040 TEFC motor with a voltage of 115V, speed of 2910 rpm, and no gearbox. Key specifications include a rated speed of 2907.9 rpm, torque of 3.1 lb-in, current of 1.88 amps, output power of 107 watts, and efficiency of 50.9%. Startup conditions include a current of 3.18 amps and torque of 3.04 lb-in. A graph shows efficiency and speed curves versus torque.
Groschopp 05318 specsheet
This document provides specifications for an AC 1 Ph 8060 TEFC motor with a voltage of 230V, speed of 3000 rpm, and no gearbox. Key specifications include a rated speed of 3000.6 rpm, torque of 4.5lb-in, current of 1.30 amps, output of 161 watts, and efficiency of 57.1%. A graph shows efficiency and speed versus torque from 0 to 3600 rpm.
Groschopp 05318 specsheet
This document provides specifications for an AC 1 Ph 8060 TEFC motor with a voltage of 230V, speed of 3000 rpm, and no gearbox. Key specifications include a rated speed of 3000.6 rpm, torque of 4.5lb-in, current of 1.30 amps, output of 161 watts, and efficiency of 57.1%. A graph shows efficiency and speed versus torque from 0 to 3600 rpm.
Groschopp 05126 specsheet
The document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 115V, speed of 3150 rpm, and no gearbox. Key specs include a rating of 3152.3 rpm and 1.1 lb-in of torque at 0.69 amps and 41 watts of output. The motor has a breakdown speed of 2462.14 rpm and pullup speed of 0 rpm. It has a continuous duty cycle and system efficiency of 52.6%. Start/stall conditions are 1.58 amps and 0.93 lb-in of torque. Performance charts show efficiency versus torque and speed.
Groschopp 05156 specsheet
This document provides specifications for an AC 3 Phase 6540 TEFC motor with a voltage of 230V, frequency of 50Hz, and speed of 1250rpm without a gearbox. Key specifications include a rated speed of 1245rpm, startup current of 0.52amps, and maximum torque of 3.3lb-in. Performance charts show efficiency peaks at 33.4% and torque decreases with increasing speed. The motor is sold and serviced by Electromate.
Groschopp 05124 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor that operates at 115v 60Hz with a maximum speed of 2990 rpm. The motor has an output of 53 watts, 0.0717 HP, and torque of 1.5lb-in at its rated speed of 2988.9 rpm. Charts show torque and efficiency curves for the motor under cold and hot operating conditions.
Groschopp 05314 specsheet
This document provides specifications for an AC single-phase 8060 TEFC motor with a voltage of 115V, speed of 3000 rpm, and no gearbox. The motor has a rated speed of 3001.9 rpm, torque of 4.7 lb-in, current of 2.64 amps, output of 168 watts, and efficiency of 56.8%. Startup conditions include a current of 4.88 amps and torque of 4.45 lb-in. A graph shows efficiency and speed curves versus torque in both cold and hot conditions.
Groschopp 05314 specsheet
This document provides specifications for an AC single-phase 8060 TEFC motor with a voltage of 115V, speed of 3000 rpm, and no gearbox. The motor has a rated speed of 3001.9 rpm, torque of 4.7 lb-in, current of 2.64 amps, output of 168 watts, and efficiency of 56.8%. Startup conditions include a current of 4.88 amps and torque of 4.45 lb-in. A graph shows efficiency and speed curves versus torque in both cold and hot conditions.
Similar to Groschopp 05136 specsheet (20)
More from Electromate
Automated screw thread quality checking using SMAC LAR55 actuator new produc...
The document discusses an automated screw thread quality checking solution using SMAC LAR55 actuators. It allows 100% inspection of screw threads to check for issues like oversizing, cross-threading, depth, and pitch. This can help automakers meet higher quality standards by eliminating defective parts and providing immediate feedback. The LAR55's precision Z-theta motion makes it suitable for automatically checking screw threads.
An overview of the various kinematic models in both parallel and serial robot...
This document provides an overview of kinematic models for parallel and serial robotic mechanisms and their suitability for precision applications. It introduces Ilian Bonev, a professor at École de technologie supérieure who is an expert in parallel robots and precision robotics. It then describes some parallel robots that have been developed at the Control and Robotics Laboratory including ones for medical, manufacturing, and research applications. The document concludes with sections on robot calibration methods and the differences between serial and parallel mechanisms.
Galil motion control robotic symposium presentation-linear motion from non-li...
The document discusses non-linear robotic motion control solutions. It describes how Galil Motion Control provides controllers for various types of non-linear robots like SCARA and delta robots. It covers topics like selecting the robot topology, designing each joint, motor selection, forward and inverse kinematics equations, vibration reduction techniques, and examples of implementing motion control for SCARA robots.
Advanced motion controls robotics symposium presentation-open standard tools ...
This document discusses the development of control software for a linear delta robot used in 3D printing. It describes using PLCopen function blocks and XML files to create reusable software components for robot kinematics and handling G-code from slicing programs. Function block diagrams are created to process G-code, set coordinate systems, and represent the overall project logic. The solution involves creating user-defined function blocks to handle the robot's inverse kinematics and translate G-code commands into motions.
Maxon motor ag robotic symposium presentation-impedance control overview and ...
The document discusses impedance control, an approach to robot control that models mechanical systems as electrical circuits using impedance. It defines electrical and mechanical impedance analogously and describes how components like resistors, inductors, and capacitors correspond to dampers, masses, and springs physically. The document outlines applications of impedance control and emphasizes the importance of selecting low-inertia motors, high-efficiency gears, and fast, accurate sensors and controllers. Overall, the document argues that impedance control requires creative engineering of mechanical designs and electrical components.
Kollmorgen robotic symposium presentation-motor design impacts on the optimiz...
The document discusses how motor design impacts the optimization of robotic systems. It explains that frameless motors can enable smaller, lighter and faster robots through their direct drive capabilities and high torque density. The document also covers various motor topologies and important concepts like torque constant, motor size constant, and how they relate to continuous torque capacity, efficiency and losses. Application examples discussed include collaborative robots, surgical robots, and mobile robots.
Harmonic drive llc robotics symposium presentation-designing from the inside ...
The document discusses defining robot performance requirements and how customized solutions from Harmonic Drive can help meet those requirements. It provides an overview of Harmonic Drive's product line and gear technologies, then discusses how mechanical modifications and performance customizations can be made to their gear components and systems to optimize robots for specific design requirements and applications. Customizations like increased accuracy, stiffness, torque properties and materials can be made, with varying levels of difficulty and cost implications discussed.
Thomson Linear Dual Shaft Rail 2DA Modular Specs
This document provides specifications and dimensional drawings for Thomson Industries' Dual Shaft Rail linear guides with modular carriages. It includes part numbers, dimensions, load ratings and descriptions of the components. Linear guides use dual linear race shaft rails and modular carriages with open type Super Smart Ball Bushings. They are used in continuously supported applications requiring rigidity and are adaptable to any drive system.
Thomson Linear 2DA QuickSlide System with Brake
This document provides specifications for Thomson Industries' 2DA QuickSlide system with brake, including:
- It offers manual locking with infinite positioning, no carriage surface deflection when locked, and immediate availability in common sizes.
- The locking mechanism does not increase load on the bearing and allows zero axial movement during locking.
- It provides a fully supported dual shaft assembly for maximum rigidity and unlimited travel.
Thomson Linear RoundRail 2CA Web Universal Carriage Specs
This document contains specifications for Thomson Industries' Twin Shaft Web Linear Guide system. It includes dimensions, part numbers, load ratings and descriptions of the components. The linear guides use a double shaft and welded web design for improved torque strength and deflection characteristics. They are designed to move medium loads with low friction and are commonly used when bridging gaps.
Thomson Linear RoundRail 1VC Double End Supported Specs
The document provides specifications for various FluoroNyliner linear guide components including:
- Pillow blocks, twin pillow blocks, shaft end support blocks, and mounting table tops for different size linear guides ranging from 0.375 to 1.5 inches in diameter.
- It lists the part numbers, dimensions, materials, weights, and other specifications for each component.
- It also includes an illustration of a double end supported linear guide system with pillow blocks, shafts, end supports, and a size B mounting table top.
Thomson Linear RoundRail 2CA Web Flanged Carriage Specs
This document provides specifications for Thomson Industries' Twin Shaft Web Linear Guide system. It includes dimensions, load capacity information, and part numbers for various components of the 2CA linear guide, which features a flanged carriage design and double linear race shaft for improved torque and deflection characteristics. Configuration and installation details are also listed.
Thomson Linear RoundRail Twin Shaft Web 2CA
The document provides specifications for Thomson RoundRail linear guides and components. It includes dimensions, features, and part numbering for twin shaft web linear guides in both vertical and horizontal configurations ranging from 0.5 to 1 inch in diameter. Load capacity charts are provided for different guide sizes and configurations that can support loads between 165 to 3000 pounds depending on the model. Maximum guide lengths are listed as 72 inches and engineering calculations for shaft deflection are also noted.
Thomson Linear RoundRail 1VC Double Unsupported Specs
The document contains specifications for various FluoroNyliner linear guide parts, including dimensions, part numbers, materials, load ratings, and performance notes. It lists 14 different linear guide parts with nominal diameters ranging from 0.375 to 1.5 inches. For each part, it provides dimensions for components like bearing blocks, carriages, and table tops. It also includes general information on specifying linear guides and product notes on materials and lubrication.
Thomson Linear WhisperTrak Actuators
The Thomson WhisperTrak electric linear actuator offers a compact, quiet, and durable solution for applications requiring linear motion. It is particularly well-suited for personal mobility, medical, and rehabilitation equipment due to its small size and silent operation. The actuator provides reliable, maintenance-free movement and has an IP67 rating, making it protected against water and dust. Its flexibility and high performance in a small package make it suitable for a wide range of industries.
Thomson T-Series Profile Rail
The document provides information on the T-Series Ball Profile Rail from Thomson, including:
- It is lightweight, highly flexible, and forgiving, making it suitable for applications with poor misalignment.
- It has a low cost of installation as it can be mounted directly to non-machined bases without special tools.
- It offers industry standard dimensions and dimensions interchangeable with other rail brands, allowing for easy replacement.
Thomson Linear RoundRail Accessories Collapsable Bellows Specs
This document provides specifications for various bellows that can be used to protect slides and shafts. It lists different part numbers for bellows with a range of nominal shaft diameters from 1/4 to 1 1/2 inches. The bellows are made of polyester cover and PVC stiffeners. Dimensions such as length, width, and height are provided for each part number. Some bellows are single shaft while others are dual shaft or for horizontal vs vertical systems. Each bellows comes with attachment pieces like Velcro or mounting brackets.
Thomson Linear Roundrail Dual Shaft Rail 2DA Specs
The document provides specifications for Danaher Motion's dual shaft rail linear guides with integrated carriages. It includes dimensions, load ratings, dynamic capacities, and part numbering for the 2DA series linear guides available in nominal diameters of 0.5, 0.75, and 1.0 inches. Both full and short length carriage options are detailed along with components, material specifications, and the supplier contact information.
Thomson Linear RoundRail Continuous Support 1PC Specs
This document provides specifications for various linear guide assemblies with table tops from Thomson Industries. It includes dimensions, part numbers, load ratings and limit data for single rail linear guides with sizes ranging from M12 to M40 diameter in configurations with 4 pillow blocks, 2 twin pillow blocks or no pillow blocks and size E or F table tops. Mounting details and specifications are provided for the various components including rails, pillow blocks and table tops.
Thomson Linear RoundRail Continuous Support 1PB Specs
The document contains specifications for various continuously supported linear guide assemblies and their components. It lists part numbers, dimensions, load ratings, and other technical specifications for linear guides, support rails, pillow blocks, and bearings. Materials include aluminum alloys and bearings include ball bushings. Linear guides are specified by part number plus length and provide continuous support for applications requiring rigidity.
More from Electromate (20)
Automated screw thread quality checking using SMAC LAR55 actuator new produc...
Automated screw thread quality checking using SMAC LAR55 actuator new produc...
An overview of the various kinematic models in both parallel and serial robot...
An overview of the various kinematic models in both parallel and serial robot...
Galil motion control robotic symposium presentation-linear motion from non-li...
Galil motion control robotic symposium presentation-linear motion from non-li...
Advanced motion controls robotics symposium presentation-open standard tools ...
Advanced motion controls robotics symposium presentation-open standard tools ...
Maxon motor ag robotic symposium presentation-impedance control overview and ...
Maxon motor ag robotic symposium presentation-impedance control overview and ...
Kollmorgen robotic symposium presentation-motor design impacts on the optimiz...
Kollmorgen robotic symposium presentation-motor design impacts on the optimiz...
Harmonic drive llc robotics symposium presentation-designing from the inside ...
Harmonic drive llc robotics symposium presentation-designing from the inside ...
Thomson Linear RoundRail 2CA Web Universal Carriage Specs
Thomson Linear RoundRail 2CA Web Universal Carriage Specs
Thomson Linear RoundRail 1VC Double End Supported Specs
Thomson Linear RoundRail 1VC Double End Supported Specs
Thomson Linear RoundRail 2CA Web Flanged Carriage Specs
Thomson Linear RoundRail 2CA Web Flanged Carriage Specs
Thomson Linear RoundRail 1VC Double Unsupported Specs
Thomson Linear RoundRail 1VC Double Unsupported Specs
Thomson Linear RoundRail Accessories Collapsable Bellows Specs
Thomson Linear RoundRail Accessories Collapsable Bellows Specs
Thomson Linear Roundrail Dual Shaft Rail 2DA Specs
Thomson Linear Roundrail Dual Shaft Rail 2DA Specs
Thomson Linear RoundRail Continuous Support 1PC Specs
Thomson Linear RoundRail Continuous Support 1PC Specs
Thomson Linear RoundRail Continuous Support 1PB Specs
Thomson Linear RoundRail Continuous Support 1PB Specs
Recently uploaded
Uni Systems Copilot event_05062024_C.Vlachos.pdf
Unlocking Productivity: Leveraging the Potential of Copilot in Microsoft 365, a presentation by Christoforos Vlachos, Senior Solutions Manager – Modern Workplace, Uni Systems
Introducing Milvus Lite: Easy-to-Install, Easy-to-Use vector database for you...
Join us to introduce Milvus Lite, a vector database that can run on notebooks and laptops, share the same API with Milvus, and integrate with every popular GenAI framework. This webinar is perfect for developers seeking easy-to-use, well-integrated vector databases for their GenAI apps.
Climate Impact of Software Testing at Nordic Testing Days
My slides at Nordic Testing Days 6.6.2024
Climate impact / sustainability of software testing discussed on the talk. ICT and testing must carry their part of global responsibility to help with the climat warming. We can minimize the carbon footprint but we can also have a carbon handprint, a positive impact on the climate. Quality characteristics can be added with sustainability, and then measured continuously. Test environments can be used less, and in smaller scale and on demand. Test techniques can be used in optimizing or minimizing number of tests. Test automation can be used to speed up testing.
Cosa hanno in comune un mattoncino Lego e la backdoor XZ?
ABSTRACT: A prima vista, un mattoncino Lego e la backdoor XZ potrebbero avere in comune il fatto di essere entrambi blocchi di costruzione, o dipendenze di progetti creativi e software. La realtà è che un mattoncino Lego e il caso della backdoor XZ hanno molto di più di tutto ciò in comune.
Partecipate alla presentazione per immergervi in una storia di interoperabilità, standard e formati aperti, per poi discutere del ruolo importante che i contributori hanno in una comunità open source sostenibile.
BIO: Sostenitrice del software libero e dei formati standard e aperti. È stata un membro attivo dei progetti Fedora e openSUSE e ha co-fondato l'Associazione LibreItalia dove è stata coinvolta in diversi eventi, migrazioni e formazione relativi a LibreOffice. In precedenza ha lavorato a migrazioni e corsi di formazione su LibreOffice per diverse amministrazioni pubbliche e privati. Da gennaio 2020 lavora in SUSE come Software Release Engineer per Uyuni e SUSE Manager e quando non segue la sua passione per i computer e per Geeko coltiva la sua curiosità per l'astronomia (da cui deriva il suo nickname deneb_alpha).
Securing your Kubernetes cluster_ a step-by-step guide to success !
Today, after several years of existence, an extremely active community and an ultra-dynamic ecosystem, Kubernetes has established itself as the de facto standard in container orchestration. Thanks to a wide range of managed services, it has never been so easy to set up a ready-to-use Kubernetes cluster.
However, this ease of use means that the subject of security in Kubernetes is often left for later, or even neglected. This exposes companies to significant risks.
In this talk, I'll show you step-by-step how to secure your Kubernetes cluster for greater peace of mind and reliability.
“I’m still / I’m still / Chaining from the Block”
“An Outlook of the Ongoing and Future Relationship between Blockchain Technologies and Process-aware Information Systems.” Invited talk at the joint workshop on Blockchain for Information Systems (BC4IS) and Blockchain for Trusted Data Sharing (B4TDS), co-located with with the 36th International Conference on Advanced Information Systems Engineering (CAiSE), 3 June 2024, Limassol, Cyprus.
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...Edge AI and Vision Alliance
For the full video of this presentation, please visit: https://www.edge-ai-vision.com/2024/06/building-and-scaling-ai-applications-with-the-nx-ai-manager-a-presentation-from-network-optix/
Robin van Emden, Senior Director of Data Science at Network Optix, presents the “Building and Scaling AI Applications with the Nx AI Manager,” tutorial at the May 2024 Embedded Vision Summit.
In this presentation, van Emden covers the basics of scaling edge AI solutions using the Nx tool kit. He emphasizes the process of developing AI models and deploying them globally. He also showcases the conversion of AI models and the creation of effective edge AI pipelines, with a focus on pre-processing, model conversion, selecting the appropriate inference engine for the target hardware and post-processing.
van Emden shows how Nx can simplify the developer’s life and facilitate a rapid transition from concept to production-ready applications.He provides valuable insights into developing scalable and efficient edge AI solutions, with a strong focus on practical implementation.Large Language Model (LLM) and it’s Geospatial Applications
Large Language Model (LLM) and it’s Geospatial Applications.
Generative AI Deep Dive: Advancing from Proof of Concept to Production
Join Maher Hanafi, VP of Engineering at Betterworks, in this new session where he'll share a practical framework to transform Gen AI prototypes into impactful products! He'll delve into the complexities of data collection and management, model selection and optimization, and ensuring security, scalability, and responsible use.
20240605 QFM017 Machine Intelligence Reading List May 2024
Everything I found interesting about machines behaving intelligently during May 2024
Pushing the limits of ePRTC: 100ns holdover for 100 days
At WSTS 2024, Alon Stern explored the topic of parametric holdover and explained how recent research findings can be implemented in real-world PNT networks to achieve 100 nanoseconds of accuracy for up to 100 days.
Full-RAG: A modern architecture for hyper-personalization
Mike Del Balso, CEO & Co-Founder at Tecton, presents "Full RAG," a novel approach to AI recommendation systems, aiming to push beyond the limitations of traditional models through a deep integration of contextual insights and real-time data, leveraging the Retrieval-Augmented Generation architecture. This talk will outline Full RAG's potential to significantly enhance personalization, address engineering challenges such as data management and model training, and introduce data enrichment with reranking as a key solution. Attendees will gain crucial insights into the importance of hyperpersonalization in AI, the capabilities of Full RAG for advanced personalization, and strategies for managing complex data integrations for deploying cutting-edge AI solutions.
Unlock the Future of Search with MongoDB Atlas_ Vector Search Unleashed.pdf
Discover how MongoDB Atlas and vector search technology can revolutionize your application's search capabilities. This comprehensive presentation covers:
* What is Vector Search?
* Importance and benefits of vector search
* Practical use cases across various industries
* Step-by-step implementation guide
* Live demos with code snippets
* Enhancing LLM capabilities with vector search
* Best practices and optimization strategies
Perfect for developers, AI enthusiasts, and tech leaders. Learn how to leverage MongoDB Atlas to deliver highly relevant, context-aware search results, transforming your data retrieval process. Stay ahead in tech innovation and maximize the potential of your applications.
#MongoDB #VectorSearch #AI #SemanticSearch #TechInnovation #DataScience #LLM #MachineLearning #SearchTechnology
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...
The choice of an operating system plays a pivotal role in shaping our computing experience. For decades, Microsoft's Windows has dominated the market, offering a familiar and widely adopted platform for personal and professional use. However, as technological advancements continue to push the boundaries of innovation, alternative operating systems have emerged, challenging the status quo and offering users a fresh perspective on computing.
One such alternative that has garnered significant attention and acclaim is Nitrux Linux 3.5.0, a sleek, powerful, and user-friendly Linux distribution that promises to redefine the way we interact with our devices. With its focus on performance, security, and customization, Nitrux Linux presents a compelling case for those seeking to break free from the constraints of proprietary software and embrace the freedom and flexibility of open-source computing.
Alt. GDG Cloud Southlake #33: Boule & Rebala: Effective AppSec in SDLC using ...
Effective Application Security in Software Delivery lifecycle using Deployment Firewall and DBOM
The modern software delivery process (or the CI/CD process) includes many tools, distributed teams, open-source code, and cloud platforms. Constant focus on speed to release software to market, along with the traditional slow and manual security checks has caused gaps in continuous security as an important piece in the software supply chain. Today organizations feel more susceptible to external and internal cyber threats due to the vast attack surface in their applications supply chain and the lack of end-to-end governance and risk management.
The software team must secure its software delivery process to avoid vulnerability and security breaches. This needs to be achieved with existing tool chains and without extensive rework of the delivery processes. This talk will present strategies and techniques for providing visibility into the true risk of the existing vulnerabilities, preventing the introduction of security issues in the software, resolving vulnerabilities in production environments quickly, and capturing the deployment bill of materials (DBOM).
Speakers:
Bob Boule
Robert Boule is a technology enthusiast with PASSION for technology and making things work along with a knack for helping others understand how things work. He comes with around 20 years of solution engineering experience in application security, software continuous delivery, and SaaS platforms. He is known for his dynamic presentations in CI/CD and application security integrated in software delivery lifecycle.
Gopinath Rebala
Gopinath Rebala is the CTO of OpsMx, where he has overall responsibility for the machine learning and data processing architectures for Secure Software Delivery. Gopi also has a strong connection with our customers, leading design and architecture for strategic implementations. Gopi is a frequent speaker and well-known leader in continuous delivery and integrating security into software delivery.
GraphSummit Singapore | Neo4j Product Vision & Roadmap - Q2 2024
Maruthi Prithivirajan, Head of ASEAN & IN Solution Architecture, Neo4j
Get an inside look at the latest Neo4j innovations that enable relationship-driven intelligence at scale. Learn more about the newest cloud integrations and product enhancements that make Neo4j an essential choice for developers building apps with interconnected data and generative AI.
Building RAG with self-deployed Milvus vector database and Snowpark Container...
This talk will give hands-on advice on building RAG applications with an open-source Milvus database deployed as a docker container. We will also introduce the integration of Milvus with Snowpark Container Services.
Recently uploaded (20)
Introducing Milvus Lite: Easy-to-Install, Easy-to-Use vector database for you...
Introducing Milvus Lite: Easy-to-Install, Easy-to-Use vector database for you...
Climate Impact of Software Testing at Nordic Testing Days
Climate Impact of Software Testing at Nordic Testing Days
Cosa hanno in comune un mattoncino Lego e la backdoor XZ?
Cosa hanno in comune un mattoncino Lego e la backdoor XZ?
Securing your Kubernetes cluster_ a step-by-step guide to success !
Securing your Kubernetes cluster_ a step-by-step guide to success !
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...
Large Language Model (LLM) and it’s Geospatial Applications
Large Language Model (LLM) and it’s Geospatial Applications
Generative AI Deep Dive: Advancing from Proof of Concept to Production
Generative AI Deep Dive: Advancing from Proof of Concept to Production
20240605 QFM017 Machine Intelligence Reading List May 2024
20240605 QFM017 Machine Intelligence Reading List May 2024
Pushing the limits of ePRTC: 100ns holdover for 100 days
Pushing the limits of ePRTC: 100ns holdover for 100 days
Full-RAG: A modern architecture for hyper-personalization
Full-RAG: A modern architecture for hyper-personalization
Unlock the Future of Search with MongoDB Atlas_ Vector Search Unleashed.pdf
Unlock the Future of Search with MongoDB Atlas_ Vector Search Unleashed.pdf
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...
Alt. GDG Cloud Southlake #33: Boule & Rebala: Effective AppSec in SDLC using ...
Alt. GDG Cloud Southlake #33: Boule & Rebala: Effective AppSec in SDLC using ...
GraphSummit Singapore | Neo4j Product Vision & Roadmap - Q2 2024
GraphSummit Singapore | Neo4j Product Vision & Roadmap - Q2 2024
Building RAG with self-deployed Milvus vector database and Snowpark Container...
Building RAG with self-deployed Milvus vector database and Snowpark Container...
Groschopp 05136 specsheet
- 1. Prepared by: Groschopp.com 02/24/14 Motor: Voltage: Speed: Gearbox: AC 3 Ph 6540 TEFC 230 v 60 Hz 1570 rpm 4 Poles None Product ID: 5136 SPECIFICATIONS Rating: Speed: Torque: Current: Output: Output: 1569.7 rpm 1.4lb-in 0.31 amps 27 watts 0.0357 HP Breakdown (Cold): Speed: Torque: 990.62 rpm 2.95 lb-in Pullup (Cold): Speed: Torque: 0.0 rpm 2.51lb-in Duty Cycle: On: Off: Continuous Efficiency: Gearbox: Motor: System: 34.4 % 34.4 % Start/Stall Conditions: Current: Torque: 0.59 amps 2.51 lb-in Torque (lb-in) Speed RPM Efficiency 200 0 0.0 0.3 400 0.6 600 0.9 800 1.2 1000 1.5 1200 1.8 1400 2.1 1600 2.4 1800 2.7 90.0 80.0 70.0 60.0 50.0 40.0 30.0 20.0 10.0 Speed, Efficiency Vs. Torque Cold Hot Notes: Sold & Serviced By: ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com