A Revisit To Forchheimer Equation Applied In Porous Media FlowIJRES Journal
A brief reference to various non-linear forms of relation between hydraulic gradient and velocity of
flow through porous media is presented, followed by the justification of the use of Forchheimer equation. In
order to study the nature of coefficients of this equation, an experimental programme was carried out under
steady state conditions, using a specially designed permeameter. Eight sizes of coarse material and three sizes
of glass spheres are used as media with water as the fluid medium. Equations for linear and non-linear
parameters of Forchheimer equation are proposed in terms of easily measurable media properties. These
equations are presented in the form of graphs as quick reckoners.
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
On Similarity of Differential Capacity and Capillary Pressure FractalKhalid Al-Khidir
On Similarity of Differential Capacity and Capillary Pressure Fractal Dimensions for Characterizing Shajara Reservoirs of the Permo-Carboniferous Shajara Formation, Saudi Arabia
A Revisit To Forchheimer Equation Applied In Porous Media FlowIJRES Journal
A brief reference to various non-linear forms of relation between hydraulic gradient and velocity of
flow through porous media is presented, followed by the justification of the use of Forchheimer equation. In
order to study the nature of coefficients of this equation, an experimental programme was carried out under
steady state conditions, using a specially designed permeameter. Eight sizes of coarse material and three sizes
of glass spheres are used as media with water as the fluid medium. Equations for linear and non-linear
parameters of Forchheimer equation are proposed in terms of easily measurable media properties. These
equations are presented in the form of graphs as quick reckoners.
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
On Similarity of Differential Capacity and Capillary Pressure FractalKhalid Al-Khidir
On Similarity of Differential Capacity and Capillary Pressure Fractal Dimensions for Characterizing Shajara Reservoirs of the Permo-Carboniferous Shajara Formation, Saudi Arabia
The Effect of Geometry Parameters and Flow Characteristics on Erosion and Sed...Dr. Amarjeet Singh
One of the most critical problems in the river
engineering field is scouring, sedimentation and morphology
of a river bed. In this paper, a finite volume method
FORTRAN code is provided and used. The code is able to
model the sedimentation. The flow and sediment were
modeled at the interception of the two channels. It is applied
an experimental model to evaluate the results. Regarding the
numerical model, the effects of geometry parameters such as
proportion of secondary channel to main channel width and
intersection angle and also hydraulic conditionals like
secondary to main channel discharge ratio and inlet flow
Froude number were studied on bed topographical and flow
pattern. The numerical results show that the maximum
height of bed increased to 32 percent as the discharge ratio
reaches to 51 percent, on average. It is observed that the
maximum height of sedimentation decreases by declining in
main channel to secondary channel Froude number ratio. On
the assessment of the channel width, velocity and final bed
height variations have changed by given trend, in all the
ratios. Also, increasing in the intersection angle accompanied
by decreasing in flow velocity variations along the channel.
The pattern of velocity and topographical bed variations are
also constant in any studied angles.
Experimental Study on Two-Phase Flow in Horizontal Rectangular Minichannel wi...IJERA Editor
An experimental study was conducted to investigate two-phase air-water flow characteristics, in horizontal
rectangular minichannel with Y-junction. The width (W), the height (H) and the hydraulic diameter (DH) of the
rectangular cross section for the upstream side of the junction are 4.60 mm, 2.50 mm and 3.24 mm, while those
for the downstream side are 2.36 mm, 2.50 mm and 2.43 mm. The entire test section was machined from
transparent acrylic block, so that the flow structure could be visualized. Liquid single-phase and air-liquid twophase
flow experiments were conducted at room temperature. The flow pattern, the bubble velocity, the bubble
length, and the void fraction were measured with a high-speed video camera. Pressure profile upstream and
downstream from the junction was also measured for the respective flows, and the pressure loss due to the
contraction at the junction was determined from the pressure profiles. Two flow patterns, i.e., slug and annular
flows, were observed in the fully-developed region apart from the junction. In the analysis, the frictional pressure
drop data, the two-phase frictional multiplier data, bubble velocity data, bubble length data and void fraction data
were compared with calculations by some correlations in literatures. In addition, new pressure loss coefficient
correlations for the pressure drop at the junction has been proposed. Results of such experiment and analysis are
described in the present paper.
Transverse relaxation time fractal dimension of nuclear magnetic resonance fo...Khalid Al-Khidir
Transverse relaxation time fractal dimension of nuclear magnetic resonance for characterizing shajara reservoirs of the permo carboniferous shajara formation, saudi arabia
The Effect of Geometry Parameters and Flow Characteristics on Erosion and Sed...Dr. Amarjeet Singh
One of the most critical problems in the river
engineering field is scouring, sedimentation and morphology
of a river bed. In this paper, a finite volume method
FORTRAN code is provided and used. The code is able to
model the sedimentation. The flow and sediment were
modeled at the interception of the two channels. It is applied
an experimental model to evaluate the results. Regarding the
numerical model, the effects of geometry parameters such as
proportion of secondary channel to main channel width and
intersection angle and also hydraulic conditionals like
secondary to main channel discharge ratio and inlet flow
Froude number were studied on bed topographical and flow
pattern. The numerical results show that the maximum
height of bed increased to 32 percent as the discharge ratio
reaches to 51 percent, on average. It is observed that the
maximum height of sedimentation decreases by declining in
main channel to secondary channel Froude number ratio. On
the assessment of the channel width, velocity and final bed
height variations have changed by given trend, in all the
ratios. Also, increasing in the intersection angle accompanied
by decreasing in flow velocity variations along the channel.
The pattern of velocity and topographical bed variations are
also constant in any studied angles.
Experimental Study on Two-Phase Flow in Horizontal Rectangular Minichannel wi...IJERA Editor
An experimental study was conducted to investigate two-phase air-water flow characteristics, in horizontal
rectangular minichannel with Y-junction. The width (W), the height (H) and the hydraulic diameter (DH) of the
rectangular cross section for the upstream side of the junction are 4.60 mm, 2.50 mm and 3.24 mm, while those
for the downstream side are 2.36 mm, 2.50 mm and 2.43 mm. The entire test section was machined from
transparent acrylic block, so that the flow structure could be visualized. Liquid single-phase and air-liquid twophase
flow experiments were conducted at room temperature. The flow pattern, the bubble velocity, the bubble
length, and the void fraction were measured with a high-speed video camera. Pressure profile upstream and
downstream from the junction was also measured for the respective flows, and the pressure loss due to the
contraction at the junction was determined from the pressure profiles. Two flow patterns, i.e., slug and annular
flows, were observed in the fully-developed region apart from the junction. In the analysis, the frictional pressure
drop data, the two-phase frictional multiplier data, bubble velocity data, bubble length data and void fraction data
were compared with calculations by some correlations in literatures. In addition, new pressure loss coefficient
correlations for the pressure drop at the junction has been proposed. Results of such experiment and analysis are
described in the present paper.
Transverse relaxation time fractal dimension of nuclear magnetic resonance fo...Khalid Al-Khidir
Transverse relaxation time fractal dimension of nuclear magnetic resonance for characterizing shajara reservoirs of the permo carboniferous shajara formation, saudi arabia
On the equality of electric power fractal dimension and capillary pressure fr...Khalid Al-Khidir
On the equality of electric power fractal dimension and capillary pressure fractal dimension for characterizing shajara reservoirs of the permo carboniferous shajara formation
Electric potential gradient fractal dimensions for characterizing shajara res...Khalid Al-Khidir
Electric potential gradient fractal dimensions for characterizing shajara reservoirs of the shajara formation of the permo carboniferous unayzah group, saudi arabia
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Flow rate fractal dimension for characterizing shajara reservoirs of the permo carboniferous shajara formation, saudi arabia
1. 1 Volume 2018 , Issue 01
Advances in Petroleum and Chemical Engineering
Alkhidir KEME. Arch Petro Chem Eng: APCE-104.
Research Article doi: 10.9016/APCE-104/1000104.
Flow rate fractal dimension for characterizing Shajara reservoirs of the Permo-
Carboniferous Shajara Formation, Saudi Arabia
Prof. Khalid Elyas Mohamed Elameen Alkhidir*
Department of Petroleum and Natural Gas Engineering, College of Engineering, King Saud University, Saudi Arabia.
*
Corresponding author: Prof. Khalid Elyas Mohamed Elameen Alkhidir, Department of Petroleum and Natural Gas Engineering,
College of Engineering, King Saud University, Saudi Arabia. Tel: +966114679118; Email: kalkhidir@ksu.edu.sa
Citation: Alkhidir KEME (2018) Flow rate fractal dimension for characterizing Shajara reservoirs of the Permo-Carboniferous
Shajara Formation, Saudi Arabia. Arch Petro Chem Eng: APCE-104. doi: 10.9016/APCE-104/1000104.
Received Date: 17 September, 2018; Accepted Date: 24 September, 2018; Published Date: 30 September, 2018
Abstract
Flow rate fractal dimension was employed to describe in details the internal pore geometrical features of real outcrop sandstone
samples of the Shajara reservoirs of the Shajara Formation, Saudi Arabia. The flow rate was derived from relationship among pore
radius, differential pressure, fluid viscosity, and capillary length. The pore radius was obtained from capillary pressure measured
by mercury injection. However, the capillary length was calculated from correlation between surface tension, contact angle, fluid
density, gravitational acceleration, and pore radius. The flow rate fractal dimension was achieved from the slope = 3-Df of the ratio
of logarithm flow rate at specific saturation to maximum flow rate versus logarithm wetting phase saturation. Through combing
field observations and acquired results of fractal dimension, the Shajara reservoirs of the Shajara Formation were divided here
into three units. These stratigraphic units from bottom to top are: lower Shajara flow Rate Fractal Dimension Unit, Middle Shajara
Flow Rate Fractal Dimension Unit, and Upper Shajara flow Rate Fractal Dimension unit. The three reservoir units were also
confirmed by capillary pressure fractal dimension As conclusive evidence the flow rate fractal dimension was found to increase
with increasing permeability and pore connectivity.
Introduction
The wetting phase saturation can be described as function of
capillary pressure and fractal dimension was demonstrated by
[1]. The Purcell model was found to be the best fit to the
experimental data of the wetting phase relative permeability for
the cases as long as the measured capillary pressure curve had
the same residual saturation as the relative permeability curve
was described by [2]. A theoretical model to correlate capillary
pressure and resistivity index based on the fractal scaling theory
was reported by [3]. The fractal dimension resulting from
longer transverse NMR relaxation times and lower capillary
pressure reflects the volume dimension of larger pores was
described by [4]. The fractal dimension derived from the short
NMR relaxation times is similar to the fractal dimension of the
internal surface was described by [4]. The fractal dimensions
can be used to represent the complexity degree and
heterogeneity of pore structure, and the coexistence of
dissolution pores and large intergranular pores of Donghetang
sandstones contributes to a heterogeneous pore throat
distribution and a high value of fractal dimension was reported
by [5]. The relationship among capillary pressure (PC), nuclear
magnetic transverse relaxation time (T2) and resistivity index
(I) was studied by [6]. An increase of bubble pressure fractal
dimension and pressure head fractal dimension and decreasing
pore size distribution index and fitting parameters m*n due to
possibility of having interconnected channels was confirmed by
[7]. An increase of fractal dimension with increasing
arithmetic, geometric relaxation time of induced polarization,
permeability and grain size was investigated by [8,9,10]. An
increase of seismo electric and resistivity fractal dimensions
with increasing permeability and grain size was described by
[11,12].
Materials and Methods
Sandstone samples were collected from the surface type section
of the Permo-Carboniferous Shajara Formation, latitude 26 52
17.4, longitude 43 36 18. (Figure1). Porosity was measured on
collected samples using mercury intrusion Porosimetry and
2. 2 Volume 2018 , Issue 01
Citation: Alkhidir KEME (2018) Flow rate fractal dimension for characterizing Shajara reservoirs of the Permo-Carboniferous
Shajara Formation, Saudi Arabia. Arch Petro Chem Eng: APCE-104. doi: 10.9016/APCE-104/1000104.
permeability was derived from capillary pressure data. The
purpose of this paper is to obtain flow rate fractal dimension
and to confirm it by capillary pressure fractal dimension. The
fractal dimension of the first procedure is determined from the
positive slope of the plot of logarithm of the ratio of flow rate
to maximum flow rate versus log wetting phase saturation
(logSw). Whereas the fractal dimension of the second
procedure is determined from the negative slope of the plot of
logarithm of log capillary pressure (log (Pc) versus logarithm
of wetting phase saturation (log Sw).
The flow rate fractal dimension can be scaled as
𝐒𝐰 = [
𝐐 𝟎.𝟐𝟓
𝐐𝐦𝐚𝐱 𝟎.𝟐𝟓
]
𝟑−𝐃𝐟
= [
𝐐
𝟏
𝟒
𝐐𝐦𝐚𝐱
𝟏
𝟒
]
𝟑−𝐃𝐟
𝟏
Where Sw the water saturation, Q the flow rate in cubic meter
/ second; Qmax the maximum flow rate in cubic meter / second,
Df the fractal dimension.
Equation 1 can be proofed from
𝐐 =
[𝛑 ∗ 𝐫 𝟒
∗ 𝚫𝐩]
[𝟖 ∗ 𝛍 ∗ 𝐋]
𝟐
Where Q the flow rate in cubic meter / second, r the pore throat
radius in meter, Δp the differential pressure in pascal, μ the
fluid viscosity in pascal* second; L the capillary length in
meter.
Equation 2 after rearrange will become
𝐫 𝟒
=
[𝟖 ∗ 𝐐 ∗ 𝛍 ∗ 𝐋]
[𝛑 ∗ 𝚫𝐩]
𝟑
The maximum flow rate can be scaled as
𝐫𝐦𝐚𝐱 𝟒
=
[𝟖 ∗ 𝐐𝐦𝐚𝐱 ∗ 𝛍 ∗ 𝐋]
[𝛑 ∗ 𝚫𝐩]
𝟒
Divide equation 3 by equation 4
𝐫 𝟒
𝐫𝐦𝐚𝐱 𝟒
=
[𝟖 ∗ 𝐐 ∗ 𝛍 ∗ 𝐋]
[𝛑 ∗ 𝚫𝐩]
[𝟖 ∗ 𝐐𝐦𝐚𝐱 ∗ 𝛍 ∗ 𝐋]
[𝛑 ∗ 𝚫𝐩]
𝟓
Equation 5 after simplification will become
𝐫 𝟒
𝐫𝐦𝐚𝐱 𝟒
= [
𝐐
𝐐𝐦𝐚𝐱
] 𝟔
Take the fourth root of equation 6
√[
𝐫 𝟒
𝐫𝐦𝐚𝐱 𝟒
]
𝟒
= √[
𝐐
𝐐𝐦𝐚𝐱
]
𝟒
𝟕
Equation 7 after simplification will become
[
𝐫
𝐫𝐦𝐚𝐱
] = [
𝐐 𝟎.𝟐𝟓
𝐐𝐦𝐚𝐱 𝟎.𝟐𝟓
] 𝟖
Take the logarithm of equation 8
𝐋𝐨𝐠 [
𝐫
𝐫𝐦𝐚𝐱
] = 𝐋𝐨𝐠 [
𝐐 𝟎.𝟐𝟓
𝐐𝐦𝐚𝐱 𝟎.𝟐𝟓
] 𝟗
𝐁𝐮𝐭 ; 𝐋𝐨𝐠 [
𝐫
𝐫𝐦𝐚𝐱
] = 𝐋𝐨𝐠
𝐒𝐰
[𝟑 − 𝐃𝐟]
𝟏𝟎
Where Sw the water saturation, Df the fractal dimension
Insert equation 10 into equation 9
𝐋𝐨𝐠
𝐒𝐰
[𝟑 − 𝐃𝐟]
= 𝐋𝐨𝐠 [
𝐐 𝟎.𝟐𝟓
𝐐𝐦𝐚𝐱 𝟎.𝟐𝟓
] 𝟏𝟏
If we remove the logarithm from equation 11
𝐒𝐰 = [
𝐐 𝟎.𝟐𝟓
𝐐𝐦𝐚𝐱 𝟎.𝟐𝟓
]
𝟑−𝐃𝐟
= [
𝐐
𝟏
𝟒
𝐐𝐦𝐚𝐱
𝟏
𝟒
]
𝟑−𝐃𝐟
𝟏𝟐
Equation 12 the proof of equation 1 which relates the water
saturation Sw, The flow rate Q, the maximum flow rate Qmax,
the fractal dimension Df.
The capillary can be scaled as
𝐋𝐨𝐠 𝐒𝐰 = [𝐃𝐟 − 𝟑] ∗ 𝐏𝐜 + 𝐜𝐨𝐧𝐬𝐭𝐚𝐧𝐭 𝟏𝟑
Where Sw the water saturation, Pc the capillary pressure, and
Df the fractal dimension
Result and discussion
Based on field observation the Shajara Reservoirs of the
Permo-Carboniferous Shajara Formation were divided here
into three units as described in Figure1.These units from
bottom to top are: Lower Shajara Reservoir, Middle Shajara
reservoir, and Upper Shajara Reservoir. Their acquired results
of the number of moles fractal dimension and capillary pressure
fractal dimension are displayed in Table 1. Based on the
attained results it was found that the flow rate fractal dimension
is equal to the capillary pressure fractal dimension. The
maximum value of the fractal dimension was found to be
2.7872 assigned to sample SJ13 from the Upper Shajara
Reservoir as verified in Table 1. Whereas the minimum value
of the fractal dimension 2.4379 was reported from sample SJ3
from the Lower Shajara reservoir as displayed in Table1. The
flow rate fractal dimension and capillary pressure fractal
dimension were observed to increase with increasing
permeability as proofed in Table1 owing to the possibility of
having interconnected channels.
The Lower Shajara reservoir was denoted by six sandstone
samples (Figure 1), four of which label as SJ1, SJ2, SJ3 and
SJ4 were selected for capillary pressure measurement as
confirmed in Table1. Their positive slopes of the first
procedure log of the ratio of flow rate to maximum flow rate
3. 3 Volume 2018 , Issue 01
Citation: Alkhidir KEME (2018) Flow rate fractal dimension for characterizing Shajara reservoirs of the Permo-Carboniferous
Shajara Formation, Saudi Arabia. Arch Petro Chem Eng: APCE-104. doi: 10.9016/APCE-104/1000104.
versus log wetting phase saturation (Sw) and negative slopes of
the second procedure log capillary pressure (Pc) versus log
wetting phase saturation (Sw) are delineated in Figure 2, Figure
3, Figure 4, and Figure 5. Their flow rate fractal dimension and
capillary pressure fractal dimension values are shown in Table
1. As we proceed from sample SJ2 to SJ3 a pronounced
reduction in permeability due to compaction was reported from
1955 md to 56 md which reflects decrease in flow rate fractal
dimension from 2.7748 to 2.4379 as specified in table 1. Again,
an increase in grain size and permeability was verified from
sample SJ4 whose flow rate fractal dimension and capillary
pressure fractal dimension was found to be 2.6843 as described
in (Table 1).
Figure 1: Surface type section of the Shajara reservoirs of the Permo-Carboniferous Shajara Formation at latitude 26 52 17.4,
longitude 43 36 18.
Figure 2: Log (Q0.25
/Qmax
0.25
) & log pc versus log Sw for
sample Sj1.
Figure 3: Log (Q0.25
/Qmax
0.25
) & log pc versus log Sw for
sample Sj2.
4. 4 Volume 2018 , Issue 01
Citation: Alkhidir KEME (2018) Flow rate fractal dimension for characterizing Shajara reservoirs of the Permo-Carboniferous
Shajara Formation, Saudi Arabia. Arch Petro Chem Eng: APCE-104. doi: 10.9016/APCE-104/1000104.
Figure 4: Log (Q0.25
/Qmax
0.25
) & log pc versus log Sw for
sample Sj3
Figure 5: Log (Q0.25
/Qmax
0.25
) & log pc versus log Sw for
sample Sj4.
In contrast, the Middle Shajara reservoir which is separated
from the Lower Shajara reservoir by an unconformity surface
as shown in Figure 1. It was designated by four samples (Figure
1), three of which named as SJ7, SJ8, and SJ9 as illustrated in
Table1 were selected for capillary measurements as described
in Table 1. Their positive slopes of the first procedure and
negative slopes of the second procedure are shown in Figure 6,
Figure 7 and Figure 8 and Table 1. Additionally, their flow rate
fractal dimensions and capillary pressure fractal dimensions
show similarities as delineated in Table 1. Their fractal
dimensions are higher than those of samples SJ3 and SJ4 from
the Lower Shajara Reservoir due to an increase in their
permeability as explained in (Table 1).
Figure 6: Log (Q0.25
/Qmax
0.25
) & log pc versus log Sw for
sample Sj7.
Figure 7: Log (Q0.25
/Qmax
0.25
) & log pc versus log Sw for
sample Sj8.
Figure 8: Log (Q0.25
/Qmax
0.25
) & log pc versus log Sw for
sample Sj9.
On the other hand, the Upper Shajara reservoir was separated
from the Middle Shajara reservoir by yellow green mudstone
as revealed in Figure 1. It is defined by three samples so called
SJ11, SJ12, SJ13 as explained in Table 1. Their positive slopes
of the first procedure and negative slopes of the second
procedure are displayed in Figure 9, Figure 10 and Figure 11
and Table 1. Moreover, their flow rate fractal dimension and
capillary pressure fractal dimension are also higher than those
of sample SJ3 and SJ4 from the Lower Shajara Reservoir due
to an increase in their permeability as clarified in (Table 1).
Figure 9: Log (Q0.25
/Qmax
0.25
) & log pc versus log Sw for
sample Sj11.
5. 5 Volume 2018 , Issue 01
Citation: Alkhidir KEME (2018) Flow rate fractal dimension for characterizing Shajara reservoirs of the Permo-Carboniferous
Shajara Formation, Saudi Arabia. Arch Petro Chem Eng: APCE-104. doi: 10.9016/APCE-104/1000104.
Figure 10: Log (Q0.25
/Qmax
0.25
) & log pc versus log Sw for
sample Sj12.
Figure 11: Log (Q0.25
/Qmax
0.25
) & log pc versus log Sw for
sample Sj13.
Overall a plot of number of flow rate dimension versus
capillary pressure fractal dimension as shown in Figure 12
reveals three permeable zones of varying Petrophysical
properties. Such variation in fractal dimension can account for
heterogeneity which is a key parameter in reservoir quality
assessment. This reservoir heterogeneity was also confirmed by
plotting positive slope of the first procedure versus negative
slope of the second procedure as described in (Figure 13).
Figure 12: Flow rate fractal dimension versus capillary
pressure fractal dimension.
Figure 13: Slope of the first procedure versus slope of the
second procedure.
Conclusion
• The sandstones of the Shajara Reservoirs of the
Shajara formation permo-Carboniferous were divided
here into three units based on flow rate fractal
dimension.
• The Units from base to top are: Lower Shajara flow
rate Fractal dimension Unit, Middle Shajara flow rate
Fractal Dimension Unit, and Upper Shajara flow rate
Fractal Dimension Unit.
• These units were also proved by capillary pressure
fractal dimension.
• The fractal dimension was found to increase with
increasing grain size and permeability.
Acknowledgement
The author would to thank King Saud University, College of
Engineering, Department of Petroleum and Natural Gas
Engineering, Department of Chemical Engineering, Research
Centre at College of Engineering, and King Abdullah Institute
for Research and Consulting Studies for their Supports.
References
1. Toledo GT, Navy RA, Davis HT, Scriven LE (1994)
Capillary pressure, water relative permeability, electrical
conductivity and capillary dispersion coefficient of fractal
porous media at low wetting phase saturation. SPE
advanced technology Series 2: 136-141.
2. Li K, Horne RN (2002) Experimental verification of
methods to calculate relative permeability using capillary
pressure data. SPE 76757, Proceedings of the 2002 SPE
Western Region Meeting/AAPG Pacific Section Joint
Meeting held in Anchorage, Alaska.
3. Li K, Willams W (2007) Determination of capillary
Pressure function from resistivity data. Transp. Porous
Media 67: 1-15.
4. Zhang Z, Weller A (2014) Fractal Dimension of Pore-
Space Geometry of Eocene sandstone formation.
Geophysics 79: D377-D387.