This document describes a graduate project report on using cashew nut shells as an agricultural waste adsorbent for the removal of phenol from wastewater. The aim is to investigate the capability of cashew nut shells to remove phenol and study the effects of parameters like initial phenol concentration, adsorbent dosage, contact time and temperature on adsorption. The project involves preparing and characterizing the adsorbent, optimizing operating conditions, and conducting kinetic and equilibrium studies to analyze adsorption data using isotherm models. The results show that cashew nut shells activated with sulfuric acid can effectively remove 57.18% of phenol from wastewater, close to the predicted removal of 61.006
IRJET- Preparation of Activated Carbon from PolystyreneIRJET Journal
This document summarizes research on preparing activated carbon from polystyrene waste. The researchers used polystyrene waste to create activated carbon via pyrolysis followed by thermal activation. They tested the activated carbon produced for characteristics like moisture content, ash content, density, solubility in water and acid, pH, decolorizing power, phenol number, and iron content. Batch experiments showed the polystyrene-derived activated carbon effectively removed pollutants like chloride from water, with around 80-85% removal achieved within 5 hours. The activated carbon produced adsorption properties similar to commercially available activated carbon. The study thus provides an effective way to utilize polystyrene waste through conversion to useful activated carbon.
SOLVENT EXTRACTION AND ADSORPTION TECHNIQUE FOR THE TREATMENT OF PESTICIDE EF...civej
Solvent extraction and adsorption techniques are effective methods for the removal of pesticides like DDT
and Dicofol from the waste water. Study was conducted using 3 different solvents- Ethylene dichloride
(EDC), Monochlorobenzene (MCB) and Hexane to optimise parameters like effluent to solvent ratio,
agitation speed, agitation time and settling time to attain maximum removal of pesticides by solvent
extraction process. MCB was found to be the best solvent when compared to other two solvents using the
optimised parameters. The activated carbon (8 x30) is an effective adsorbent for the removal of DDT and
Dicofol. The material have good adsorptive capacity and follows Freundlich model. The optimum
adsorbent dose was observed as 2 gm/100ml and optimum contact time needed to reach the equilibrium
was observed as 3 hr. Column study was conducted with the synthetic effluent after solvent extraction.
Combination of solvent extraction process and adsorption technique was very effective for the removal of
Dicofol and DDT with an efficiency of 99 % and 97 % respectively.
Photocatalytic Degradation of Ciprofloxacin using TiO2 in a Slurry Photocatal...ijtsrd
A slurry photocatalytic reactor assessed for the degradation of ciprofloxacin CFX . The effect of operating parameters like initial ciprofloxacin concentration, catalyst dosage and pH on ciprofloxacin degradation was analysed in this study. Batch study was conducted and it showed 90 degradation of the CFX. It was observed the optimum concentration of CFX was 1500 µg l, catalyst dosage was 1 g l at the pH of 9 for the duration of 3 hours. The photocatalytic degradation of CFX followed the pseudo first order kinetics. Karthika. V | Vedavalli. S | Afreen Begum. M "Photocatalytic Degradation of Ciprofloxacin using TiO2 in a Slurry Photocatalytic Reactor: Optimization" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-4 | Issue-4 , June 2020, URL: https://www.ijtsrd.com/papers/ijtsrd31224.pdf Paper Url :https://www.ijtsrd.com/engineering/environment-engineering/31224/photocatalytic-degradation-of-ciprofloxacin-using-tio2-in-a-slurry-photocatalytic-reactor-optimization/karthika-v
This document summarizes a study on the removal of Safranin dye from aqueous solution using sodium phosphate (NaP) zeolite synthesized from coal fly ash. The study investigated the thermodynamic and kinetic properties of Safranin dye adsorption onto the synthesized zeolite. Characterization techniques including XRF, SEM, XRD and FTIR were used to analyze the zeolite. Batch adsorption experiments showed maximum dye removal of 97.14% at an equilibrium pH of 9.0, adsorbent dose of 5 g/L, and contact time of 180 minutes. Adsorption data fitted well to Langmuir and Freundlich isotherm models. Kinetic data showed best fit
The document summarizes the synthesis and characterization of zeolite from coal fly ash and its application in removing inorganic and organic pollutants from wastewater. Key points:
- Zeolite was synthesized from coal fly ash via an alkali fusion process followed by hydrothermal treatment. The synthesized zeolite was characterized using various techniques.
- Batch adsorption studies were conducted to investigate the ability of synthesized zeolite to remove heavy metals like copper, cadmium, lead and dye (safranin) from wastewater. Parameters like contact time, dose, pH and concentration were optimized.
- Adsorption isotherm models like Langmuir, Freundlich, Tem
An Evaluation of Commercial Textile Tannins Based on Their Inert COD Content ...Tolga Tezgel
This study evaluated two common tannin formulations used in the textile dyeing process - Tannin 1 and Tannin 2 - to determine their inert chemical oxygen demand (COD) levels and toxicity. Both tannins had high levels of initially inert soluble COD, accounting for 59% and 41% of total COD respectively. Acute toxicity tests on bacteria Vibrio fischeri found that both tannins were toxic, with Tannin 2 showing considerably higher toxicity. The results indicate that effluents containing these tannins require specific pretreatment to reduce their recalcitrance and toxicity before mixing and conventional biological treatment.
International Journal of Engineering (IJE) Volume (2) Issue (4)CSCJournals
This document summarizes an experimental study on treating distillery effluent using an aerobic reactor with sewage sludge as a seed culture. Microorganisms in the sewage sludge were isolated and identified. The reactor was operated at different initial substrate concentrations and samples analyzed over time for COD, TSS, TDS and pH. The first-order and diffusional models best described the kinetic data, showing decreasing rate constants with increasing initial concentration. The Singh model provided a poor fit. Maximum COD removals of 78-88% were achieved.
FA-DSDME for the analysis of 18 pesticides in human blood, JCA 2015Dr. Rupender K. Singh
This document describes a new sample preparation technique called fast agitated directly suspended droplet microextraction (FA-DSDME) for the extraction and pre-concentration of 18 organophosphorus pesticides from human blood samples prior to analysis by liquid chromatography-tandem mass spectrometry (LC-MS/MS). The key advantages of this technique over other microextraction methods are that it uses automated agitation to deliberately split and recombine the organic extraction droplets, avoiding the need for dispersive solvents or centrifugation. Recoveries of 86-109% were obtained with detection limits ranging from 0.0009 to 0.122 μg/L. The method showed good precision, enrichment factors from 30 to 132, and was not
IRJET- Preparation of Activated Carbon from PolystyreneIRJET Journal
This document summarizes research on preparing activated carbon from polystyrene waste. The researchers used polystyrene waste to create activated carbon via pyrolysis followed by thermal activation. They tested the activated carbon produced for characteristics like moisture content, ash content, density, solubility in water and acid, pH, decolorizing power, phenol number, and iron content. Batch experiments showed the polystyrene-derived activated carbon effectively removed pollutants like chloride from water, with around 80-85% removal achieved within 5 hours. The activated carbon produced adsorption properties similar to commercially available activated carbon. The study thus provides an effective way to utilize polystyrene waste through conversion to useful activated carbon.
SOLVENT EXTRACTION AND ADSORPTION TECHNIQUE FOR THE TREATMENT OF PESTICIDE EF...civej
Solvent extraction and adsorption techniques are effective methods for the removal of pesticides like DDT
and Dicofol from the waste water. Study was conducted using 3 different solvents- Ethylene dichloride
(EDC), Monochlorobenzene (MCB) and Hexane to optimise parameters like effluent to solvent ratio,
agitation speed, agitation time and settling time to attain maximum removal of pesticides by solvent
extraction process. MCB was found to be the best solvent when compared to other two solvents using the
optimised parameters. The activated carbon (8 x30) is an effective adsorbent for the removal of DDT and
Dicofol. The material have good adsorptive capacity and follows Freundlich model. The optimum
adsorbent dose was observed as 2 gm/100ml and optimum contact time needed to reach the equilibrium
was observed as 3 hr. Column study was conducted with the synthetic effluent after solvent extraction.
Combination of solvent extraction process and adsorption technique was very effective for the removal of
Dicofol and DDT with an efficiency of 99 % and 97 % respectively.
Photocatalytic Degradation of Ciprofloxacin using TiO2 in a Slurry Photocatal...ijtsrd
A slurry photocatalytic reactor assessed for the degradation of ciprofloxacin CFX . The effect of operating parameters like initial ciprofloxacin concentration, catalyst dosage and pH on ciprofloxacin degradation was analysed in this study. Batch study was conducted and it showed 90 degradation of the CFX. It was observed the optimum concentration of CFX was 1500 µg l, catalyst dosage was 1 g l at the pH of 9 for the duration of 3 hours. The photocatalytic degradation of CFX followed the pseudo first order kinetics. Karthika. V | Vedavalli. S | Afreen Begum. M "Photocatalytic Degradation of Ciprofloxacin using TiO2 in a Slurry Photocatalytic Reactor: Optimization" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-4 | Issue-4 , June 2020, URL: https://www.ijtsrd.com/papers/ijtsrd31224.pdf Paper Url :https://www.ijtsrd.com/engineering/environment-engineering/31224/photocatalytic-degradation-of-ciprofloxacin-using-tio2-in-a-slurry-photocatalytic-reactor-optimization/karthika-v
This document summarizes a study on the removal of Safranin dye from aqueous solution using sodium phosphate (NaP) zeolite synthesized from coal fly ash. The study investigated the thermodynamic and kinetic properties of Safranin dye adsorption onto the synthesized zeolite. Characterization techniques including XRF, SEM, XRD and FTIR were used to analyze the zeolite. Batch adsorption experiments showed maximum dye removal of 97.14% at an equilibrium pH of 9.0, adsorbent dose of 5 g/L, and contact time of 180 minutes. Adsorption data fitted well to Langmuir and Freundlich isotherm models. Kinetic data showed best fit
The document summarizes the synthesis and characterization of zeolite from coal fly ash and its application in removing inorganic and organic pollutants from wastewater. Key points:
- Zeolite was synthesized from coal fly ash via an alkali fusion process followed by hydrothermal treatment. The synthesized zeolite was characterized using various techniques.
- Batch adsorption studies were conducted to investigate the ability of synthesized zeolite to remove heavy metals like copper, cadmium, lead and dye (safranin) from wastewater. Parameters like contact time, dose, pH and concentration were optimized.
- Adsorption isotherm models like Langmuir, Freundlich, Tem
An Evaluation of Commercial Textile Tannins Based on Their Inert COD Content ...Tolga Tezgel
This study evaluated two common tannin formulations used in the textile dyeing process - Tannin 1 and Tannin 2 - to determine their inert chemical oxygen demand (COD) levels and toxicity. Both tannins had high levels of initially inert soluble COD, accounting for 59% and 41% of total COD respectively. Acute toxicity tests on bacteria Vibrio fischeri found that both tannins were toxic, with Tannin 2 showing considerably higher toxicity. The results indicate that effluents containing these tannins require specific pretreatment to reduce their recalcitrance and toxicity before mixing and conventional biological treatment.
International Journal of Engineering (IJE) Volume (2) Issue (4)CSCJournals
This document summarizes an experimental study on treating distillery effluent using an aerobic reactor with sewage sludge as a seed culture. Microorganisms in the sewage sludge were isolated and identified. The reactor was operated at different initial substrate concentrations and samples analyzed over time for COD, TSS, TDS and pH. The first-order and diffusional models best described the kinetic data, showing decreasing rate constants with increasing initial concentration. The Singh model provided a poor fit. Maximum COD removals of 78-88% were achieved.
FA-DSDME for the analysis of 18 pesticides in human blood, JCA 2015Dr. Rupender K. Singh
This document describes a new sample preparation technique called fast agitated directly suspended droplet microextraction (FA-DSDME) for the extraction and pre-concentration of 18 organophosphorus pesticides from human blood samples prior to analysis by liquid chromatography-tandem mass spectrometry (LC-MS/MS). The key advantages of this technique over other microextraction methods are that it uses automated agitation to deliberately split and recombine the organic extraction droplets, avoiding the need for dispersive solvents or centrifugation. Recoveries of 86-109% were obtained with detection limits ranging from 0.0009 to 0.122 μg/L. The method showed good precision, enrichment factors from 30 to 132, and was not
This document summarizes a study that investigated the removal of nitrate from groundwater using activated carbon prepared from rice husk and sludge from a paper industry wastewater treatment plant. The key findings are:
- Activated carbon from rice husk achieved a maximum nitrate removal of 93.5 mg/g at pH 4 and 4 hours of contact time. Activated carbon from paper industry sludge achieved 79.5 mg/g removal under the same conditions.
- Adsorption was best fitted by the Langmuir isotherm model and followed pseudo-second order kinetics.
- Increasing the ratio of ZnCl2 used for activation improved adsorption capacity, with a 1:
Treatment of Effluent from Granite Cutting Plant by Using Natural Adsorbents ...IJERD Editor
Granite cutting plant is one such industry that releases polluting and turbid effluent. The residue from all these processes is discharged with water as an effluent. The effluent mainly contains many solids that harm the environment. Hence it requires treatment techniques before disposal. Several conventional methods are available for removal of contaminants like coagulation, adsorption, polyelectrolyte methods and biological methods. Most of them are cost prohibitive. The reduction of solids concentration in the effluent before disposal by using the techniques, coagulation followed by adsorption using natural adsorbents, like rice husk carbon and saw dust carbon, in contrast to the usage of activated carbon as it is costly. From a local Granite cutting plant near Anantapur, the effluent is collected and its physico-chemical characteristics are estimated and found to be pH(7.5), TS(4240mg/l), TSS(21560mg/l), TDS(12373mg/l).Effluent obtained is subjected to coagulation by potash alum followed by adsorption using saw dust carbon and rice husk carbon.
Adsorption of Methylene blue and Malachite Green in Aqueous Solution using Ja...IJEAB
The adsorption of mixture of two basic dyes methylene blue and malachite green in aqueous solution onto jack fruit leaf ash in a batch system with respect to initial dye concentrations, pH, contact time, shaker speed and adsorbent doses was investigated.. The pseudo-first-order and pseudo-second- order kinetics model were used to describe the kinetic data. The rate constants at different pH values (3-9.1) were evaluated. The experimental data fitted well with the pseudo-second-order kinetic model. Equilibrium isotherms were analyzed by Langmuir, Freundlich and Temkin isotherm models. Maximum adsorption capacity was 20.41mg/g was achieved by Langmuir isotherm model. Error analysis was done to find the best model that described the experimental data well and it was the Langmuir model. The result indicated that jack fruit leaf ash could be fruitfully employed as low cost adsorbent for the removal of mixture of two basic dyes MB and MG from the wastewater.
Fertilizer plant waste carbon slurry has been investigated after some processing as an adsorbent for the removal of dyes and phenols using columns. The results show that the carbonaceous adsorbent prepared from carbon slurry being porous and having appreciable surface area (380 m2/g) can remove dyes both cationic (meldola blue, methylene blue, chrysoidine G, crystal violet) as well as anionic (ethyl orange, metanil yellow, acid blue 113), and phenols (phenol, 2-chlorophenol, 4-chlorophenol and 2,4-dichlorophenol) fruitfully from water. The column type continuous flow operations were used to obtain the breakthrough curves. The breakthrough capacity, exhaustion capacity and degree of column utilization were evaluated from the plots. The results shows that the degree of column utilization for dyes lies in the range 60 to 76% while for phenols was in the range 53-58%. The exhaustion capacities were quite high as compared to the breakthrough capacities and were found to be 217, 211, 104, 126, 233, 248, 267 mg/g for meldola blue, crystal violet, chrysoidine G, methylene blue, ethyl orange, metanil yellow, acid blue 113, respectively and 25.6, 72.2, 82.2 and 197.3 mg/g for phenol, 2-chlorophenol, 4-chlorophenol and 2,4-dichlorophenol, respectively
Removal of fluoride from drinking water by adsorption onto Activated Alumina ...IJERA Editor
This document summarizes a study on removing fluoride from drinking water using adsorption onto activated alumina and activated carbon. It describes how the rate of fluoride removal was examined under different experimental parameters such as contact time, fluoride concentration, adsorbent dosage, and pH. The maximum fluoride removal was achieved using activated carbon at a dosage of 2g/L, contact time of 40 minutes, and pH of 7. Optimal fluoride removal from more concentrated solutions required higher dosages. Activated alumina also effectively removed fluoride when tested under various conditions.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
This document presents a study that used sonication (ultrasound) to remediate soil contaminated with 2-methylpropane-2-thiol. A central composite design and response surface methodology were used to model and optimize the effects of sonication power, time, and water content on removal efficiency. The model showed that power and time had the greatest effects on removal efficiency. Under optimal conditions of high power and long sonication time with a lower water content, a maximum removal efficiency of 82.83% was achieved.
Air pollution mitigation of poison gas co with crude chlorophyll of papaya (c...Alexander Decker
1. The document discusses a study on using crude chlorophyll extract from papaya (Carica papaya L.) leaves to mitigate air pollution from carbon monoxide (CO) gas.
2. The study found that the papaya leaf chlorophyll extract solution had the ability to absorb CO gas, and that a solution with a 1:4 ratio of papaya leaf acetone extract to distilled water was optimal for CO gas absorption.
3. No color changes were observed in the test solutions, indicating the absorption process was physical in nature. The optimal time for the papaya leaf chlorophyll extract solution to absorb 1000ppm of CO pollutants was found to be 10 minutes.
Optimum Conditions for the Removal of Cadmium from Aqueous Solution with Bamb...theijes
The performance of two varieties of Bamboo activated carbon (CABC washed and CABC unwashed), produced by chemical activation with ZnCl2, was evaluated through batch adsorption studies for the removal of Cadmium from aqueous solution. The effects of adsorbent dose, initial concentration of cadmium, agitation time, adsorbate p and, particle size were used as variables to obtain the optimum conditions for the removal of cadmium. Results obtained revealed that as the adsorbent dose increased, the amount adsorbed per unit mass decreased indicating that more active sites were utilized at smaller adsorbent dose. Also, the effects of initial cadmium concentration showed that percentage removal rate increased with increase in cadmium concentration due to availability of more metal ions at higher concentrations. Thus, all the carbons achieved at least 82.62% removal at initial Cadmium concentration of 50mg/l. The optimum pH was 5 and 7 for CABC unwashed and CABC washed respectively while the optimum particle size was 50μm for all the carbon tested. Furthermore, CABC unwashed performed better as an adsorbent because it achieved 71.48% removal of Cadmium in 60 minutes, while CABC washed achieved 69.46% removal in 120mins.
Chemical Examination Of Sandbox (Hura Crepitans) Seed: Proximate, Elemental A...IOSRJAC
A study in terms of proximate, elemental and fatty acid contents of (Hura crepitans) seed was investigated using standard analytical techniques. The results of proximate composition in % were as follows: moisture 12.82 ± 0.01, crude protein 24.76 ±0.04, crude fibre 10.15 ± 0.03, fat 10.68 ± 0.01, ash 3.16 ± 0.02 and carbohydrate 34.75 ± 0.05. The elemental composition of the seed showed Na, K, Ca and Mg in mg/100g to be 6.00 ± 0.01, 123.00 ± 0.02, 10.40 ± 0.03, 112.00 ± 0.01 respectively while other elements determined in mg/kg were Fe and Zn with 7.10 ±0.04 and 2.60± 0.01. The (%) free fatty acid compositions of the seed oil were as follows: lauric (1.310 ±0.015), palmitic (0.389 ±0.012), palmitoleic (1.211 ±0.013), stearic (2.436 ± 0.004), oleic (6.138 ±0.003), linoleic (8.625 ±0.001) and linolenic (2.469 ± 0.102). The results revealed linoleic and oleic acids to be the most common in terms of abundance while palmitic acid was the least. The seed of Hura crepitans could be described as a good food because it contained significant amount of essential nutrients required by man.
This document discusses using soil washing with nonionic surfactants to remove phenanthrene (PHE) contamination from soil, and then using activated carbon to selectively adsorb the surfactants from the washed solution for recovery and reuse. Four nonionic surfactants - Tween 40, Tween 80, Brij 30 and Brij 35 - were tested for their ability to solubilize PHE and for their adsorption to soil. Brij 30 showed the highest solubilization of PHE and lowest adsorption to soil, making it most effective for soil washing. Activated carbon was then able to selectively adsorb 85-89% of the surfactants from the washed solutions, allowing recovery. However
The document discusses using low-cost walnut shells to remove two common pesticides, carbofuran and chloropyriphos, from aqueous solutions. Walnut shells were treated chemically and thermally to increase their surface area and porosity for effective adsorption. Batch and column adsorption methods were used to study the adsorption of pesticides under different conditions. Adsorption parameters like pH, contact time, concentration, and kinetics were analyzed. The treated walnut shells showed high adsorption capacity of 97-99% within 30 minutes. The adsorption process was found to be dependent on pH. The document also characterized the adsorbent material using SEM, FT-IR, and surface area analysis
IRJET- Improvement of Sludge Reduction Efficiency of Ozonation by Microbubble...IRJET Journal
This document discusses improving the efficiency of sludge reduction through ozonation using microbubble aeration technology and catalysis. It finds that adding hydrogen peroxide (H2O2) as a catalyst and using microbubbles generated by a linear mixer pipe can significantly increase the biodegradability and reduce the mass of sludge. Key results include an oil content reduction from 77.48% to 51.7% after ozonation. Mixed liquor suspended solids (MLSS) and mixed liquor volatile suspended solids (MLVSS) were also reduced, while COD and NH4+ levels increased. The linear mixer pipe was found to be more effective for microbubble generation and sludge treatment than a jet
The document summarizes research on using activated carbon prepared from olive stone waste to sorb copper, zinc, and nickel ions from aqueous solutions. Olive stone activated carbon (OSAC) was prepared under different physical activation conditions and characterized. OSAC-3, activated at 900°C for 3.5 hours, had the highest surface area and was selected for further study. Batch experiments were conducted to determine optimum sorption conditions and kinetics. The maximum sorption capacities were 25.38 mg/g for Cu2+, 16.95 mg/g for Zn2+, and 14.65 mg/g for Ni2+. Sorption was best described by pseudo-second order kinetics and was spontaneous and endothermic/exothermic
This document summarizes a study that investigated the effectiveness of using activated carbon produced from snail shells for treating wastewater from beverage industries. Snail shells were pyrolyzed and activated with phosphoric acid. Characterization of the activated samples showed they had higher surface area, porosity, and pH than the non-activated sample. Treatment of beverage wastewater with the activated carbon significantly reduced parameters like BOD, COD, turbidity and phosphate over treatment times of 10-40 minutes. The study concluded that activated carbon from snail shells is effective for wastewater treatment from beverage industries.
Oily wastewater treatment using polyamide thin film composite membraneMedhat Elzahar
This document summarizes a study that used polyamide thin film composite reverse osmosis membrane filtration to treat edible oil wastewater emulsions. The membrane was characterized and its performance was tested for treating wastewater with oil concentrations between 3000-6000 mg/L. Experimental results showed that adding an activated carbon pre-treatment unit prior to the reverse osmosis membrane increased chemical oxygen demand removal from 94% to 99% and permeate flux from 34 L/m2hr to 75 L/m2hr. The reverse osmosis membrane filtration coupled with activated carbon was found to be an effective hybrid technique for removing over 99% of contaminants from high concentration edible oil wastewater.
1) The document examines the effect of two activated sludge preservation methods - pre-aeration and cold storage - on the sludge's adsorption capacity.
2) Batch experiments were conducted using fresh activated sludge as well as sludge that had been pre-aerated for 4 hours, pre-aerated for 24 hours, or cold-stored for 6 hours. Glucose was used as the adsorbate in the experiments.
3) The results showed that pre-aeration increased the sludge's adsorption capacity, while cold storage resulted in a lower adsorption capacity compared to fresh sludge. There was no significant difference between 4-hour and 24-hour pre-aeration.
Modified magnetite nanoparticles with cetyltrimethylammonium bromide as super...Iranian Chemical Society
This paper reports application of cetyltrimethylammonium bromide (CTAB) coated magnetite nanoparticles (Fe3O4 NPs) as a novel adsorbent for removal of two types of disperse dyes, including disperse red 167, and disperse blue 183, from wastewater of textile companies. The effect of parameters including type of surfactant, pH of solution, surfactant concentration, and amount of salt, was investigated and optimized. The obtained results showed that the ratio of initial dye concentration to CTAB amounts has critical effect on removal processes so that removal efficiencies higher than 95% can be achieved even at high concentration of dyes as high as 500 mg l-1 when the ratio is optimum. Removal of dyes is very fast, and equilibrium is reached at times less than 10 min even for high concentration of the dyes. Very high adsorbent capacity (as high as 2000 mg g-1) was yielded for maximum tested concentration of the dyes (500 mg g-1). The obtained result was confirmed by thermogravimetric analysis data. This study showed that CTAB coated Fe3O4 NPs is a very efficient adsorbent for removal of dyes from wastewater of textile companies and has high capacity under optimum conditions.
Defluoridization Using a Natural Adsorbent, Strychnos PotatorumIJERA Editor
The study assessed the suitability of low-cost natural adsorbent to effectively remediate fluoride contaminated water. The removal of fluoride from aqueous solution by using Strychnos Potatorum was studied in batch technique. Influence of pH, adsorbent dose, contact time, co ions, speed and initial concentration on the adsorption were investigated. The maximum removal of fluoride ion was obtained at pH 7. The removal of fluoride was expressed with Langmuir and Freundlich isotherm. It was found that the sufficient time for adsorption equilibrium of fluoride ion was 1 hour. The removal of fluoride ions was maximum for the adsorbent dosage of SP is 50mg/50ml. The fluoride adsorption was maximum at 60minutes. The adsorption of F- ion was maximum in the shaking speed of 120 rpm. The presence of interfering ions such as nitrate and carbonate showed positive effect while sulphate and chloride showed little negative effect and phosphate showed high negative effect for the adsorbent. The optimum initial fluoride concentration for SP adsorbent was 1mg/50ml.
This document summarizes a study that investigated the removal of nitrate from groundwater using activated carbon prepared from rice husk and sludge from a paper industry wastewater treatment plant. The key findings are:
- Activated carbon from rice husk achieved a maximum nitrate removal of 93.5 mg/g at pH 4 and 4 hours of contact time. Activated carbon from paper industry sludge achieved 79.5 mg/g removal under the same conditions.
- Adsorption was best fitted by the Langmuir isotherm model and followed pseudo-second order kinetics.
- Increasing the ratio of ZnCl2 used for activation improved adsorption capacity, with a 1:
Treatment of Effluent from Granite Cutting Plant by Using Natural Adsorbents ...IJERD Editor
Granite cutting plant is one such industry that releases polluting and turbid effluent. The residue from all these processes is discharged with water as an effluent. The effluent mainly contains many solids that harm the environment. Hence it requires treatment techniques before disposal. Several conventional methods are available for removal of contaminants like coagulation, adsorption, polyelectrolyte methods and biological methods. Most of them are cost prohibitive. The reduction of solids concentration in the effluent before disposal by using the techniques, coagulation followed by adsorption using natural adsorbents, like rice husk carbon and saw dust carbon, in contrast to the usage of activated carbon as it is costly. From a local Granite cutting plant near Anantapur, the effluent is collected and its physico-chemical characteristics are estimated and found to be pH(7.5), TS(4240mg/l), TSS(21560mg/l), TDS(12373mg/l).Effluent obtained is subjected to coagulation by potash alum followed by adsorption using saw dust carbon and rice husk carbon.
Adsorption of Methylene blue and Malachite Green in Aqueous Solution using Ja...IJEAB
The adsorption of mixture of two basic dyes methylene blue and malachite green in aqueous solution onto jack fruit leaf ash in a batch system with respect to initial dye concentrations, pH, contact time, shaker speed and adsorbent doses was investigated.. The pseudo-first-order and pseudo-second- order kinetics model were used to describe the kinetic data. The rate constants at different pH values (3-9.1) were evaluated. The experimental data fitted well with the pseudo-second-order kinetic model. Equilibrium isotherms were analyzed by Langmuir, Freundlich and Temkin isotherm models. Maximum adsorption capacity was 20.41mg/g was achieved by Langmuir isotherm model. Error analysis was done to find the best model that described the experimental data well and it was the Langmuir model. The result indicated that jack fruit leaf ash could be fruitfully employed as low cost adsorbent for the removal of mixture of two basic dyes MB and MG from the wastewater.
Fertilizer plant waste carbon slurry has been investigated after some processing as an adsorbent for the removal of dyes and phenols using columns. The results show that the carbonaceous adsorbent prepared from carbon slurry being porous and having appreciable surface area (380 m2/g) can remove dyes both cationic (meldola blue, methylene blue, chrysoidine G, crystal violet) as well as anionic (ethyl orange, metanil yellow, acid blue 113), and phenols (phenol, 2-chlorophenol, 4-chlorophenol and 2,4-dichlorophenol) fruitfully from water. The column type continuous flow operations were used to obtain the breakthrough curves. The breakthrough capacity, exhaustion capacity and degree of column utilization were evaluated from the plots. The results shows that the degree of column utilization for dyes lies in the range 60 to 76% while for phenols was in the range 53-58%. The exhaustion capacities were quite high as compared to the breakthrough capacities and were found to be 217, 211, 104, 126, 233, 248, 267 mg/g for meldola blue, crystal violet, chrysoidine G, methylene blue, ethyl orange, metanil yellow, acid blue 113, respectively and 25.6, 72.2, 82.2 and 197.3 mg/g for phenol, 2-chlorophenol, 4-chlorophenol and 2,4-dichlorophenol, respectively
Removal of fluoride from drinking water by adsorption onto Activated Alumina ...IJERA Editor
This document summarizes a study on removing fluoride from drinking water using adsorption onto activated alumina and activated carbon. It describes how the rate of fluoride removal was examined under different experimental parameters such as contact time, fluoride concentration, adsorbent dosage, and pH. The maximum fluoride removal was achieved using activated carbon at a dosage of 2g/L, contact time of 40 minutes, and pH of 7. Optimal fluoride removal from more concentrated solutions required higher dosages. Activated alumina also effectively removed fluoride when tested under various conditions.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
This document presents a study that used sonication (ultrasound) to remediate soil contaminated with 2-methylpropane-2-thiol. A central composite design and response surface methodology were used to model and optimize the effects of sonication power, time, and water content on removal efficiency. The model showed that power and time had the greatest effects on removal efficiency. Under optimal conditions of high power and long sonication time with a lower water content, a maximum removal efficiency of 82.83% was achieved.
Air pollution mitigation of poison gas co with crude chlorophyll of papaya (c...Alexander Decker
1. The document discusses a study on using crude chlorophyll extract from papaya (Carica papaya L.) leaves to mitigate air pollution from carbon monoxide (CO) gas.
2. The study found that the papaya leaf chlorophyll extract solution had the ability to absorb CO gas, and that a solution with a 1:4 ratio of papaya leaf acetone extract to distilled water was optimal for CO gas absorption.
3. No color changes were observed in the test solutions, indicating the absorption process was physical in nature. The optimal time for the papaya leaf chlorophyll extract solution to absorb 1000ppm of CO pollutants was found to be 10 minutes.
Optimum Conditions for the Removal of Cadmium from Aqueous Solution with Bamb...theijes
The performance of two varieties of Bamboo activated carbon (CABC washed and CABC unwashed), produced by chemical activation with ZnCl2, was evaluated through batch adsorption studies for the removal of Cadmium from aqueous solution. The effects of adsorbent dose, initial concentration of cadmium, agitation time, adsorbate p and, particle size were used as variables to obtain the optimum conditions for the removal of cadmium. Results obtained revealed that as the adsorbent dose increased, the amount adsorbed per unit mass decreased indicating that more active sites were utilized at smaller adsorbent dose. Also, the effects of initial cadmium concentration showed that percentage removal rate increased with increase in cadmium concentration due to availability of more metal ions at higher concentrations. Thus, all the carbons achieved at least 82.62% removal at initial Cadmium concentration of 50mg/l. The optimum pH was 5 and 7 for CABC unwashed and CABC washed respectively while the optimum particle size was 50μm for all the carbon tested. Furthermore, CABC unwashed performed better as an adsorbent because it achieved 71.48% removal of Cadmium in 60 minutes, while CABC washed achieved 69.46% removal in 120mins.
Chemical Examination Of Sandbox (Hura Crepitans) Seed: Proximate, Elemental A...IOSRJAC
A study in terms of proximate, elemental and fatty acid contents of (Hura crepitans) seed was investigated using standard analytical techniques. The results of proximate composition in % were as follows: moisture 12.82 ± 0.01, crude protein 24.76 ±0.04, crude fibre 10.15 ± 0.03, fat 10.68 ± 0.01, ash 3.16 ± 0.02 and carbohydrate 34.75 ± 0.05. The elemental composition of the seed showed Na, K, Ca and Mg in mg/100g to be 6.00 ± 0.01, 123.00 ± 0.02, 10.40 ± 0.03, 112.00 ± 0.01 respectively while other elements determined in mg/kg were Fe and Zn with 7.10 ±0.04 and 2.60± 0.01. The (%) free fatty acid compositions of the seed oil were as follows: lauric (1.310 ±0.015), palmitic (0.389 ±0.012), palmitoleic (1.211 ±0.013), stearic (2.436 ± 0.004), oleic (6.138 ±0.003), linoleic (8.625 ±0.001) and linolenic (2.469 ± 0.102). The results revealed linoleic and oleic acids to be the most common in terms of abundance while palmitic acid was the least. The seed of Hura crepitans could be described as a good food because it contained significant amount of essential nutrients required by man.
This document discusses using soil washing with nonionic surfactants to remove phenanthrene (PHE) contamination from soil, and then using activated carbon to selectively adsorb the surfactants from the washed solution for recovery and reuse. Four nonionic surfactants - Tween 40, Tween 80, Brij 30 and Brij 35 - were tested for their ability to solubilize PHE and for their adsorption to soil. Brij 30 showed the highest solubilization of PHE and lowest adsorption to soil, making it most effective for soil washing. Activated carbon was then able to selectively adsorb 85-89% of the surfactants from the washed solutions, allowing recovery. However
The document discusses using low-cost walnut shells to remove two common pesticides, carbofuran and chloropyriphos, from aqueous solutions. Walnut shells were treated chemically and thermally to increase their surface area and porosity for effective adsorption. Batch and column adsorption methods were used to study the adsorption of pesticides under different conditions. Adsorption parameters like pH, contact time, concentration, and kinetics were analyzed. The treated walnut shells showed high adsorption capacity of 97-99% within 30 minutes. The adsorption process was found to be dependent on pH. The document also characterized the adsorbent material using SEM, FT-IR, and surface area analysis
IRJET- Improvement of Sludge Reduction Efficiency of Ozonation by Microbubble...IRJET Journal
This document discusses improving the efficiency of sludge reduction through ozonation using microbubble aeration technology and catalysis. It finds that adding hydrogen peroxide (H2O2) as a catalyst and using microbubbles generated by a linear mixer pipe can significantly increase the biodegradability and reduce the mass of sludge. Key results include an oil content reduction from 77.48% to 51.7% after ozonation. Mixed liquor suspended solids (MLSS) and mixed liquor volatile suspended solids (MLVSS) were also reduced, while COD and NH4+ levels increased. The linear mixer pipe was found to be more effective for microbubble generation and sludge treatment than a jet
The document summarizes research on using activated carbon prepared from olive stone waste to sorb copper, zinc, and nickel ions from aqueous solutions. Olive stone activated carbon (OSAC) was prepared under different physical activation conditions and characterized. OSAC-3, activated at 900°C for 3.5 hours, had the highest surface area and was selected for further study. Batch experiments were conducted to determine optimum sorption conditions and kinetics. The maximum sorption capacities were 25.38 mg/g for Cu2+, 16.95 mg/g for Zn2+, and 14.65 mg/g for Ni2+. Sorption was best described by pseudo-second order kinetics and was spontaneous and endothermic/exothermic
This document summarizes a study that investigated the effectiveness of using activated carbon produced from snail shells for treating wastewater from beverage industries. Snail shells were pyrolyzed and activated with phosphoric acid. Characterization of the activated samples showed they had higher surface area, porosity, and pH than the non-activated sample. Treatment of beverage wastewater with the activated carbon significantly reduced parameters like BOD, COD, turbidity and phosphate over treatment times of 10-40 minutes. The study concluded that activated carbon from snail shells is effective for wastewater treatment from beverage industries.
Oily wastewater treatment using polyamide thin film composite membraneMedhat Elzahar
This document summarizes a study that used polyamide thin film composite reverse osmosis membrane filtration to treat edible oil wastewater emulsions. The membrane was characterized and its performance was tested for treating wastewater with oil concentrations between 3000-6000 mg/L. Experimental results showed that adding an activated carbon pre-treatment unit prior to the reverse osmosis membrane increased chemical oxygen demand removal from 94% to 99% and permeate flux from 34 L/m2hr to 75 L/m2hr. The reverse osmosis membrane filtration coupled with activated carbon was found to be an effective hybrid technique for removing over 99% of contaminants from high concentration edible oil wastewater.
1) The document examines the effect of two activated sludge preservation methods - pre-aeration and cold storage - on the sludge's adsorption capacity.
2) Batch experiments were conducted using fresh activated sludge as well as sludge that had been pre-aerated for 4 hours, pre-aerated for 24 hours, or cold-stored for 6 hours. Glucose was used as the adsorbate in the experiments.
3) The results showed that pre-aeration increased the sludge's adsorption capacity, while cold storage resulted in a lower adsorption capacity compared to fresh sludge. There was no significant difference between 4-hour and 24-hour pre-aeration.
Modified magnetite nanoparticles with cetyltrimethylammonium bromide as super...Iranian Chemical Society
This paper reports application of cetyltrimethylammonium bromide (CTAB) coated magnetite nanoparticles (Fe3O4 NPs) as a novel adsorbent for removal of two types of disperse dyes, including disperse red 167, and disperse blue 183, from wastewater of textile companies. The effect of parameters including type of surfactant, pH of solution, surfactant concentration, and amount of salt, was investigated and optimized. The obtained results showed that the ratio of initial dye concentration to CTAB amounts has critical effect on removal processes so that removal efficiencies higher than 95% can be achieved even at high concentration of dyes as high as 500 mg l-1 when the ratio is optimum. Removal of dyes is very fast, and equilibrium is reached at times less than 10 min even for high concentration of the dyes. Very high adsorbent capacity (as high as 2000 mg g-1) was yielded for maximum tested concentration of the dyes (500 mg g-1). The obtained result was confirmed by thermogravimetric analysis data. This study showed that CTAB coated Fe3O4 NPs is a very efficient adsorbent for removal of dyes from wastewater of textile companies and has high capacity under optimum conditions.
Defluoridization Using a Natural Adsorbent, Strychnos PotatorumIJERA Editor
The study assessed the suitability of low-cost natural adsorbent to effectively remediate fluoride contaminated water. The removal of fluoride from aqueous solution by using Strychnos Potatorum was studied in batch technique. Influence of pH, adsorbent dose, contact time, co ions, speed and initial concentration on the adsorption were investigated. The maximum removal of fluoride ion was obtained at pH 7. The removal of fluoride was expressed with Langmuir and Freundlich isotherm. It was found that the sufficient time for adsorption equilibrium of fluoride ion was 1 hour. The removal of fluoride ions was maximum for the adsorbent dosage of SP is 50mg/50ml. The fluoride adsorption was maximum at 60minutes. The adsorption of F- ion was maximum in the shaking speed of 120 rpm. The presence of interfering ions such as nitrate and carbonate showed positive effect while sulphate and chloride showed little negative effect and phosphate showed high negative effect for the adsorbent. The optimum initial fluoride concentration for SP adsorbent was 1mg/50ml.
Mass Transfer, Kinetic, Equilibrium, and Thermodynamic Study on Removal of Di...Ratnakaram Venkata Nadh
Three distinct agricultural waste materials, viz., casuarina fruit powder (CFP), sorghum stem powder
(SSP), and banana stem powder (BSP) were used as low-cost adsorbents for the removal of toxic lead(II)
from aqueous solutions. Acid treated adsorbents were characterized by scanning electron microscopy (SEM),
energy-dispersive X-ray spectroscopy (EDX), and Fourier transform infrared spectroscopy (FTIR). The
effects of parameters like adsorbent dose, pH, temperature, initial metal ion concentration, and time of
adsorption on the removal of Pb(II) were analyzed for each adsorbent individually and the efficiency order
was BSP > SSP > CFP. Based on the extent of compatibility to Freundlich/Langmuir/Dubinin–Radushkevich/
Temkin adsorption isotherms and different models (pseudo-first and second order, Boyd, Weber’s, and
Elovich), chemisorption primarily involved in the case of BSP and SSP, whereas simultaneous occurrence of
chemisorption and physisorption was proposed in the case of CFP correlating with the thermodynamic study
results conducted at different temperatures. Based on the observations, it was proposed that three kinetic
stages involve in the adsorption process, viz., diffusion of sorbate to sorbent, intra particle diffusion, and then
establishment of equilibrium. These adsorbents have a promising role towards the removal of Pb(II) from
industrial wastewater to contribute environmental protection
Degradation of phenol using sequential batch reactoreSAT Journals
Abstract The paper presents the experimental study on the use of Sequential Batch Reactor (SBR) for the degradation of phenol in the synthetic wastewater. SBR was used as a biological treatment for the reduction of COD, which is based on suspended growth system. The garden soil with cow dung was used as the seeding material in SBR, the micro-organisms that are present help in degradation of phenol as well as reducing the COD concentration. The parameters varied in the study were initial concentration of phenol in the synthetic wastewater, aeration rate and hydraulic retention time. The degradation study shows that the maximum phenol removal efficiency is 97% for 200 ppm of initial phenol concentration under 40 ml/min of aeration rate. The COD removal efficiency of 92.3% is achieved for 250 ppm of concentration of phenol. The variation in the aeration rate was found to be very effective in increasing the efficiency of SBR. For 600 ml/min of aeration, the removal efficiency of phenol and COD are respectively, 98% and 75%. But for the aeration rate of 200 ml/min the removal efficiency of COD is as high as 81.25%. Hence, with the increase in the aeration rate, there is an increase in the degradation rate of phenol and decrease in COD reduction. This study demonstrates the utilization of SBR in degrading high concentration of phenol. Keywords: Sequential Batch Reactor (SBR), Phenol, COD, Biological Treatment …
This lab report details an experiment to study the efficient removal of turbidity, color, aluminum, and total suspended solids from river water by varying coagulant dosage, pH, settling time, and stirring speed of a flocculator. An optimum dosage of 0.1mL of polyaluminum chloride was selected with an optimum pH of 7.12, settling time of 1.5 hours, and stirring speed of 250 RPM. The experiment used a Lovibond flocculator and HACH spectrophotometer and colorimeter to test the water quality parameters. Experimental results for pH and coagulant dosage did not fully agree with literature values. Results for stirring speed and settling time agreed with theories from the literature review. Errors
Evaluation of the adsorption kinetics and equilibrium for theAlexander Decker
The document evaluates the adsorption kinetics and equilibrium potential of eggshell and eggshell membrane for removing phenol from wastewater. Eggshell and its membrane were tested as natural adsorbents for phenol. Batch experiments were conducted to examine the effect of operating conditions on phenol removal. The kinetics data fitted well to the second-order model. The Langmuir isotherm model also fit the equilibrium data well without pH control. Fourier transform infrared spectroscopy confirmed the presence of functional groups like hydroxyl and carbonyl that contribute to phenol adsorption. The results indicate that eggshell could be effectively used as a low-cost, natural adsorbent for residual phenol removal from effluents.
Methylene Blue (MB) is thiazine dyes that widely use to color product in many industry such as textile, printing, leather, cosmetic and paper. Xanthogenated-Modified Chitosan Microbeads (XMCM) is use to observe the new alternative adsorbent in removing MB from water body through adsorption process. The interactions between MB and functional group in XMCM were confirmed by Fourier Transform Infrared (FT-IR). Several parameters that influence adsorption ability such as the effect of adsorbent dosage of XMCM and the effect of initial pH of MB aqueous solution were studied. This study were done at optimum condition which is at pH 4 of initial pH of MB solution, 0.01 g of initial XMCM dosage, 6 hours stirring time and temperature of (30 ± 2 ). The adsorption data fit well Langmuir model more than Freundlich model. Based on Langmuir model, the maximum monolayer adsorption capacity of MB was 21.62 mg g-1 which indicated that XMCM can be a new alternative adsorbent for removing MB.
Adsorption of dye from aqueous solutions by orange peel with Chitosan nanocom...Open Access Research Paper
This research focused on the development of adsorbents based on cheap, abundant, and locally available agricultural wastes in Tamil Nadu to adsorb dye from an aqueous solution. The goal of this study was to explore if chitosan-modified orange peel could be utilized as an adsorbent to remove colours from wastewater and if it could be employed as a traditional wastewater treatment approach in the textile sector. Using agricultural peel in decolouration technology has a lot of potential in terms of efficiency, cost-effectiveness, and environmental friendliness. Super nanocomposite is made from orange peel waste combined with chitosan nanoparticles. The purpose of this batch adsorption experiment was to determine the effects of adsorbent dosages, pH, and temperature on dye adsorption from wastewater. The experiment showed that the maximum amount of dye adsorbed was 53.3mg/g at pH 6.9 with a Temperature (of 600 C) and the adsorbent dose amount of adsorbent was 1.0g/L. The Langmuir adsorption isotherm model was used to investigate the equilibrium adsorption behaviour. The usage of orange peel with Nanocomposite as an adsorbent for the adsorption of methylene blue dye from solutions was demonstrated in this work. The functional groups and chemical compounds found in orange peels, chitosan, chitosan orange peel, chitosan nanoparticle, and chitosan nanoparticle with orange peel waste were identified using FTIR, TGA, and SEM techniques. Different types of Langmuir I, Langmuir II, Langmuir III, Langmuir IV, and the Freundlich model as adsorption isotherm models were investigated.
ER Publication,
IJETR, IJMCTR,
Journals,
International Journals,
High Impact Journals,
Monthly Journal,
Good quality Journals,
Research,
Research Papers,
Research Article,
Free Journals, Open access Journals,
erpublication.org,
Engineering Journal,
Science Journals,
This document summarizes research on the sorption of perfluorinated compounds (PFCs) to treated activated carbons. The purpose was to evaluate how pretreatment of activated carbons with HCl, NaOH, and hydrogen peroxide affected the absorption rates of PFOA and PFHxS. Testing showed that NaOH increased sorption for some carbons as expected, but not all. Hydrogen peroxide greatly improved sorption for coconut-based carbon. Further study is recommended to better understand effects of pretreatments and carbon properties on sorption behavior.
IRJET- Design of Leachate Bioreactor for Dilkap CollegeIRJET Journal
This document describes a study conducted to design a leachate bioreactor for Dilkap College in Maharashtra, India. Specifically:
- Researchers created a model tank containing layered gravel, soil, food waste from the college canteen, and additional soil to treat leachate generated from the waste.
- The leachate collected from the model would be used in an anaerobic bioreactor to convert it into methane gas, which could then be used as an energy source.
- The document reviews several other studies on leachate treatment methods, such as using solar photocatalysis and membrane bioreactor technologies to reduce leachate pollution and convert it into usable fuels.
Potential of corn husk leaves for the co removal of phenol and cyanide from w...eSAT Journals
Abstract Application of biosorbents has gained a great importance in the present scenario of waste water purification. The present work concentrates on the potential of biosorbent, Corn husk leaves, for the co-removal of phenol and cyanide from coke waste water by simultaneous adsorption and biodegradation (SAB). The microbe used in the present study is the bacteria of Serratia Sp. The entire SAB process was carried out at 30 0C and for 60 h. Theoptimum process parameters i.e. pH, initial concentration of both phenol and cyanide, adsorbent dose of corn husk leaves were analysed and their impact on the entire process were also studied. At the range of initial concentration of phenol between 100-1000 mg/L and cyanide between 10-100 mg/L, the optimum pH was obtained between 6.5-7 and an optimum adsorbent dose of 6 g/L. Multicomponent adsorption isotherms applied were Non-modified Langmuir, Modified Langmuir, Extended Langmuir and Extended Freundlich. Out of the four isotherms applied non-modified Langmuir isotherm proved to be the best fit for phenol and modified Langmuir isotherm was found to be best fit for cyanide. Phenol showed a removal percentage of 75 % by SAB process and cyanide showed a removal percentage of 83 %. The data was also non-linearly modelled for kinetic studies. Kinetic studies revealed that for both phenol and cyanide simultaneous adsorption and biodegradation took place by physisorption as well as by chemisorption. Surface diffusion is dominating for the simultaneous adsorption and biodegradation of phenol whereas in case of cyanide intraparticle diffusion is the dominating factor. Keywords: biosorbents, corn husk leaves, simultaneous adsorption and biodegradation, optimum.
This document discusses the optimization of polysulfone-based ultrafiltration membranes prepared through phase inversion. It examines how various preparation parameters, such as the concentration of the polysulfone dope solution, the solvent used, temperature, and pressure, affect the properties of the resulting membranes, including water flux and pore size. The key findings are that increasing the concentration of the dope solution or the temperature used decreases water flux by reducing pore size and porosity, while increasing pressure leads to higher water flux linearly according to Fick's law. Bubble point tests also indicate that higher dope solution concentrations produce membranes with smaller pore sizes. Overall, the study shows how preparation parameters can be optimized to control membrane properties for various separation applications.
1. The document examines the adsorptive removal of Acid Blue 45 dye from aqueous solutions using preformed flocs of ferric sulfate, manganese chloride, and manganese sulfate as adsorbents.
2. Batch experiments were conducted to analyze the effects of contact time, pH, adsorbent dosage, and to develop adsorption isotherm models. The maximum dye removal was 90%, 85%, and 65% for ferric sulfate, manganese sulfate, and manganese chloride flocs, respectively.
3. Equilibrium data fitted well to the Langmuir isotherm model, indicating monolayer adsorption on homogeneous sites. This suggests preformed floc ad
Applications of Algal Technology for a Martian Colony *Fixed*EricStephens26
This document discusses potential applications of algal technology for sustainability on a Martian colony. It describes how algae could be used to produce oxygen through photosynthesis using carbon dioxide, water and nutrients. The algae could also be used in anaerobic digestion to produce methane and hydrogen from carbohydrates. The authors conducted experiments growing algae on anaerobic digester effluent, measuring oxygen production at different carbon dioxide concentrations and flow rates. They also measured nutrient removal by the algae and methane and hydrogen production. The results showed this method could supplement a Martian colony by producing oxygen and fuels, but challenges include adjusting the carbon dioxide concentration in the atmosphere.
Applications of Algal Technology on a Martian ColonyEricStephens26
This document discusses potential applications of algal technology for sustainability on a Martian colony. It describes how algae could be used to produce oxygen through photosynthesis using carbon dioxide, water and nutrients. The algae could also be used in anaerobic digestion to produce methane and hydrogen from carbohydrates. The authors conducted experiments growing algae on anaerobic digester effluent, measuring oxygen production at different carbon dioxide concentrations and flow rates. They also measured nutrient removal by the algae and methane and hydrogen production. The results showed this method could supplement a Martian colony by producing oxygen and fuel, though challenges remain in adjusting the carbon dioxide concentration in the atmosphere.
This document discusses a research project on the thermodynamics of adsorption of 4-chlorophenol onto activated carbon. It includes an introduction that describes activated carbon, its manufacturing process, uses, phenolic derivatives like 4-chlorophenol, adsorption processes, isotherms, and thermodynamics. The project aims to study the effect of parameters like adsorbent dose, contact time, concentration and temperature on 4-chlorophenol adsorption. Adsorption equilibrium and thermodynamics parameters are determined using the Langmuir isotherm model at different temperatures. The positive value of ΔH0 indicates the adsorption is endothermic in nature.
This document summarizes a study that evaluated pesticide residue levels of imidacloprid and abamectin on tomato, cucumber, and pepper plants after spraying. Researchers sprayed the pesticides at concentrations commonly used by farmers in Palestine and measured residue levels on plant parts and in soil over 10 days using HPLC. Residue levels of both pesticides were higher than levels found in previous studies and exceeded maximum residue limits for the first 5 days. Abamectin residues were higher than imidacloprid residues, and both pesticides showed higher soil residues compared to plant residues. The degradation rates of the pesticides in soil followed first-order kinetics with high correlation.
1. REMOVAL OF PHENOL FROM
WASTEWATER USING
AGRICULTURAL WASTE
(CASHEWNUT SHELLS)
A GraduateProject Report submitted to ManipalUniversity in partialfulfilment
of the requirement for the award of the degree of
BACHELOR OF TECHNOLOGY
in
Chemical Engineering
Submitted by
Varsha Sudheer (110903248)
Kartik Kulkarni (110903014)
Under the guidance of
C.R.Girish
Assistant Professor – Senior Scale
Department of Chemical Engg.
MIT, Manipal
DEPARTMENT OF CHEMICAL ENGINEERING
MANIPAL INSTITUTE OF TECHNOLOGY
(A Constituent College of Manipal University)
MANIPAL – 576104, KARNATAKA, INDIA
May/July 2015
2. DEPARTMENT OF CHEMICAL ENGINEERING
MANIPAL INSTITUTE OF TECHNOLOGY
(A Constituent College of Manipal University)
MANIPAL – 576 104 (KARNATAKA), INDIA
Manipal
< 19.05.2015>
CERTIFICATE
This is to certify that the project titled REMOVAL OF PHENOL FROM
WASTEWATER USING AGRICULTURAL WASTE (CASHEWNUT SHELLS) is a
record of the bonafide work done by KARTIK KULKARNI & VARSHA SUDHEER
(110903014, 110903248 resp.) submitted in partial fulfilment of the requirements for the
award of the Degree of Bachelor of Technology (BTech.) in CHEMICAL
ENGINEERING of Manipal Institute of Technology Manipal, Karnataka, (A Constituent
College of Manipal University), during the academic year 2015-2016.
Mr C.R.Girish
Assistant Professor – Senior Scale
Prof. Dr. Harish Kumar
HOD, Chemical
M.I.T, MANIPAL
3. ACKNOWLEDGMENTS
It is said that what you have said is past and what you have done is history but
what you write lasts till the end. Hence I would like to take this opportunity to
thank some of the important people who made my project a fruitful experience
and express my sincere gratitude to all those who have been associated with my
project.
I express my special thanks to Mr C.R Girish (Project Supervisor) for providing
me with endless support and encouragement in all my endeavours at every
moment during my project. Without his excellent guidance, practical insights and
valuable materials this project wouldn’t have been possible or successful.
I also want to thank Mr Vinod Thomas (Director of MIT) and Dr Harish Kumar
(HOD of Chemical Department) for allowing us to conduct our project in MIT,
Manipal.
I would like to extend my gratitude to Mr Janardhan, Mr Adiga and Mr Sadanand
(Lab assistants) for their constant guidance and support. A special mention for
the HOD of Mechanical department for allowing us to conduct our experiments
in the mechanical laboratory.
4. ABSTRACT
Adsorption is the adhesion of molecules to a solid surface. This operation exploits the ability
of certain solids preferentially to concentrate specific substances from solution onto their
surfaces. Our project revolves around the use of agricultural waste for the removal of phenol
from wastewater using adsorption. Due to ease of availability and access, cashew nut shells in
particular was chosen as our adsorbent. Phenol is the priority pollutant since it is toxic and
harmful to organisms even at low concentrations. Surface and ground water are contaminated
by phenolics as a result of the continuous release of these compounds from petrochemical, coal
conversion and phenol producing industries. Therefore, the wastewaters containing phenolic
compounds must be treated before their discharging into the water streams. The aim of the
present work is to investigate the capability of industrial waste cashew nut shells to be used to
as an adsorbent for removal of phenol from wastewater and to study the effects of initial phenol
concentration, adsorbent dosage, contact time and experimental temperature on the adsorption
process and eventually to find the optimum condition.
The analysis was carried out in various tests being, preparation of the adsorbent from the raw
oily cashewnut shells to a dried powdered form, characterization of the sample in order to
understand the various properties of the adsorbent material, optimization of conditions – to
recognize the best conditions for maximum adsorption and to increase yield and efficiency and
lastly, kinetic and equilibrium studies at optimised conditions to obtain equilibrium data with
the help of various isotherms such as Langmuir, Freundlich and Temkin. The various kinetic
models studied included first order, second order and intra-particle diffusion.
Before conducting the experiments, the parameters were optimised to obtain highest yield and
efficiency. The experiments were then conducted at these optimised conditions and it was
found that the experimental percentage phenol removal from wastewater of 57.18% was close
to that of the predicted value of 61.006%. From the kinetic studies, it was established that first
order kinetic model had the highest regression value being close to one. After a detailed study
of the three isotherms, the adsorption data was found to fit Langmuir, Freundlich and Temkin
isotherms, although Langmuir and Freundlich had the closest fit.
From this project it was concluded that the regression values of Langmuir and Freundlich
isotherms being the highest and the closest, offered to be the best fit for the resulting adsorption
data. First order kinetic model having the highest regression value close to one, also resulted
in being the best fit of the three kinetic study models. The experimental percentage removal of
phenol from wastewater of 57.18% was close to that of the predicted value of 61.006% that
was developed by the software along with the optimised conditions, hence proving that
cashewnut shells activated with sulphuric acid is a potential and active adsorbent for the
removal of phenol from wastewater.
5. LIST OF TABLES
Table No Table Title Page No
4.2 Moisture content, volatile matter, ash content and fixed carbon of
the samples.
4.4 Absorbance of the various sample solutions.
4.5.1 Set experiments to be performed.
4.5.2 Regression values with insignificant terms.
4.5.3 Regression values without insignificant terms.
4.5.4 Optimised conditions, predicted and actual percentage removal.
4.5.5 Predicted vs. Actual values
4.6.1 Time vs. Average qe values
6. LIST OF FIGURES
Figure No Figure Title Page No
3.1.1 Raw cashewnut shells
3.1.2 Shells post roasting
3.1.3 Powdered cashewnut shells
4.3 Infrared spectrum for the activated sample
4.4 Absorbance vs. Concentration
4.5.1 Phenol removal w.r.t Temperature and Concentration
4.5.2 Phenol removal w.r.t. Temperature and Dosage
4.5.3 Phenol removal w.r.t Dosage and Concentration
4.5.4 Predicted vs. Actual Readings
4.6.1 log(qe – qt) vs. Time
4.6.2 t/qt vs. Time
4.6.3 qe vs. t0.5
4.7.1 Log qe vs. Log Ce
4.7.2 1/Qe vs. 1/Ce
4.7.3 Qe vs. Log Ce
7. Contents
Page No
Acknowledgement i
Abstract ii
List Of Figures iii
List Of Tables vi
Chapter 1 INTRODUCTION
1.1 Introduction
1.2 Motivation
1.3 Organization of Report
Chapter 2 BACKGROUND THEORY and/or LITERATURE REVIEW
2.1 Background Theory
2.1.1 Langmuir Isotherm
2.1.2 Freundlich Isotherm
2.1.3 Temkin Isotherm
2.2 Literature Survey and Review
Chapter 3 METHODOLOGY
3.1 Preparation of the adsorbent
3.2 Characterization of the adosrbent
3.3 FTIR Analysis
3.4 Preparation of stock solution and sample solution
3.5 Calibration of the sample solution
3.6 Optimization of conditions
3.7 Kinetic studies
3.8 Isotherm studies
Chapter 4 RESULT ANALYSIS
4.1 Introduction
4.2 Proximate Analysis
4.3 FTIR Analysis
4.4 Calibration of sample solution
4.5 Optimization of Parameters
4.6 Kinetic Studies
4.6.1 First Order
4.6.2 Second Order
4.6.3 Third Order
8. 4.7 Isotherm Studies
4.7.1 Freundlich Isotherm
4.7.2 Langmuir Isotherm
4.7.3 Temkin Isotherm
Chapter 5 CONCLUSION AND FUTURE SCOPE
5.1 Work Conclusion
5.2 Future Scope of Work
REFERENCES
ANNEXURES (OPTIONAL)
PROJECT DETAILS
9. CHAPTER 1
INTRODUCTION
1.1 Introduction
Our project revolves around the use of agricultural waste for the removal of phenol from
wastewater using adsorption. Due to ease of availability and access, cashew nut shells in
particular was chosen as our adsorbent.
Conventional methods for the removal of phenolic pollutants in aqueous solutions can be
divided into three main categories: physical, chemical and biological treatments. Among
them, physical adsorption method is generally considered to be the best, effective, low cost
and most frequently used method for the removal of phenolic pollutions. Therefore the
search for low cost and easily available adsorbents has led many researchers to search more
economic and efficient techniques of using the natural and synthetic materials as
adsorbents.
The aim of the present work is to investigate the capability of industrial waste cashew nut
shells to be used to as an adsorbent for removal of phenol from wastewater and to study the
effects of initial phenol concentration, adsorbent dosage, contact time and experimental
temperature on the adsorption process and eventually to find the optimum condition.
The expected outcome from these experiments will help give a better understanding
regarding cashew nut shells as a suitable adsorbent for the removal of phenolic pollutants
from wastewater.
1.2 Motivation
Phenol is the priority pollutant since it is toxic and harmful to organisms even at low
concentrations. Beside the toxic effects; phenolic compounds create an oxygen demand in
receiving waters, and impart taste and odour to water with minute concentrations of their
chlorinated compounds. Surface and ground water are contaminated by phenolics as a result
of the continuous release of these compounds from petrochemical, coal conversion and
phenol producing industries. Therefore, the wastewaters containing phenolic compounds
must be treated before their discharging into the water streams.
Being final year chemical engineering students and having studied wastewater treatment,
pollution control and safety, the extremity of the dangers of the presence of phenol in
untreated wastewater is a factor that cannot be neglected. Having to take up further studies
after our B.Tech, it was crucial for us to have chosen a project that was closely related to
what we had learnt all through our college years and also contribute into helping the society.
Our university being located in Manipal, is very close to multiple chemical and petroleum
10. industrial regions. Knowing that phenolic compounds have a large contribution to the
effluents from these industries, was another motivational factor to doing this project.
Sri Devi Cashew Nut industry being located in Karkala, made the attainability of our
adsorbent an easy task. The easy access and availability helped narrow down our ideas to
this particular experiment.
1.3 Organization of Report:
January 15 - February 15: Literature Survey and attainment of the raw material.
February 15 – March 15: Preparation of the adsorbent and tests and characterization of the
adsorbent.
March 15 – April 30: Optimization of parameters, Kinetic and Equilibrium studies.
April 30 – May 15: Tabulation of results, discussion and preparation of the final report.
11. CHAPTER 2
BACKGROUND THEORY
2.1 Background Theory
Adsorption is the adhesion of molecules to a solid surface. This process creates a film of
adsorbate on the surface of the adsorbent. Adsorption differs from absorption in which a
fluid permeates or is dissolved by a liquid or solid. Adsorption is a surface based process
while absorption involves the whole volume of the material. It is a surface phenomenon.
Similar to surface tension, adsorption is a consequence of surface energy. The exact nature
of bonding depends on the details of the species involved, but the adsorption process is
generally classified as physisorption or chemisorption. It may also occur due to electrostatic
attraction.
Adsorption is usually described through isotherms, that is, the amount of adsorbate on the
adsorbent as a function of its pressure (if gas) or concentration (if liquid) at constant
temperature. The quantity adsorbed is nearly always normalized by the mass of the
adsorbent to allow comparison of different materials. The isotherms taken into consideration
in our project includes, Langmuir, Freundlich and Temkin.
2.1.1 Langmuir Isotherm
Irving Langmuir was the first to derive a scientifically based adsorption isotherm in 1918.
The model applies to gases adsorbed on solid surfaces. It is a semi-empirical isotherm with
a kinetic basis and was derived based on statistical thermodynamics. It is the most common
isotherm equation to use due to its simplicity and its ability to fit a variety of adsorption
data. The Langmuir isotherm is based on four assumptions:
1. All of the adsorption sites are equivalent and each site can only accommodate on
molecule.
2. The surface is energetically homogenous and adsorbed molecules do not interact.
3. There are no phase transitions.
4. At the maximum adsorption, only a monolayer is formed. Adsorption only occurs
on localized sites on the surface, not with other adsorbates.
2.1.2 Freundlich Isotherm
Freundlich and Kuster in 1894 published the first mathematical fit to an isotherm, and is a
purely empirical formula for gaseous adsorbates.
𝒙
𝒎
= 𝒌𝑷 𝟏/𝒏
12. where x is the quantity of adsorbate adsorbed in moles, m is the mall of the adsorbent, P is
the pressure of the adsorbate (which can be changed to concentration if a solution is being
investigated rather than a gas) and k and n are empirical constants for each adsorbent-
adsorbate pair at a given temperature. The function is not adequate at very high pressures
because in reality x/m has an asymptotic maximum as pressure increases without bound. As
the temperature increases, the constants k and n change to reflect the empirical observation
that the quantity adsorbed rises more slowly and higher pressures are required to saturate
the surface.
2.1.3 Temkin Isotherm
Temkin isotherm contains a factor that explicitly takes into the account of adsorbent-
adsorbate interactions. By ignoring the extremely low and large value of concentrations, the
model assumes that heat of adsorption (function of temperature) of all molecules in the layer
would decrease linearly rather than logarithmic. The model equation after simplification is
given by:
𝒒 𝒆 = 𝑩𝒍𝒏𝑨 𝒓 + 𝑩𝒍𝒏𝑪 𝒆
where qe is the quantity adsorbed, B is the constant related to the heat of adsorption (J/mol)
and AT is the Temkin isotherm equilibrium binding constant (L/g).
Phenol removal through adsorption: The process of adsorption has an edge due to its sludge
free clean operation and complete removal of phenol from aqueous solutions having dilute
or moderate concentrations. Activated carbon (CNS) in granular or powdered form is the
most widely used adsorbent. Out of the two major types of adsorption, chemisorption will
be applied to our studies and analysis. Chemisorption involves a chemical reaction between
the surface and the adsorbate. New chemical bonds are generated at the adsorbent surface.
The strong interaction between the adsorbate and the substrate surface creates new types of
electronic bonds.
2.2 Literature Survey and Review
Several papers were available regarding the removal of phenol from wastewater using
different materials and sources for adsorbent, two of which are mentioned below.
“Removal of phenol from industrial wastewater using saw dust” by Ihsan Habib Dakhil
from Al-Muthamma University, Iraq. The adsorbent used for his experiment was saw dust
and the various parameters considered included, initial phenol concentration, adsorbent
dose and contact time. In addition to these parameters, we are taking temperature into
account. Temperature plays a very important role in determining the chemical activity and
highest possible yields, i.e removal of phenol. In this study we concluded that the
13. percentage removal of phenol was considerably affected by initial phenol concentration,
amount of adsorbent dose, pH value and mixing contact time. The results also indicated
that the percentage of removal increased with increasing amount of adsorbent dosage and
the uptake of phenol took place at natural pH value and equilibrium occurred at 120
minutes.
“Removal of phenol from aqueous solutions by rice husk ash and activated carbon” by M.
Kermani and B.Bina. The adsorbent used for their analysis includes rice husk ash which
was prepared at three different temperatures, being 300, 400 and 500 degrees, and
activated carbon. The parameters taken into consideration were same as those of paper 1
with the addition of the adsorption isotherms. The results obtained showed that the
optimum conditions were contact time of 5 hours, pH of 5, high dosage of rice husk ash,
initial concentration of phenol between 10 -300 mg/l. Fruendlich and Langmuir models
were used to describe the relationship between the amount of phenol adsorbed and its
equilibrium concentrations.
“Removal of phenol pollutants from aqueous solutions using various adsorbents” by D K
Singh and Bhavana Srivastava. This paper stands out from the rest due to the use of various
adsorbents rather than just one. Some of them include ion exchange resins, zinc silicate,
activated carbon from straw and used rubber tyres etc. The various parameters taken into
consideration include: Effect of adsorbate concentration, adsorbate dose, contact time and
pH. Temperature again is the added parameter taken into consideration in our experiments
with the exclusion of pH. A comparison between non-conventional adsorbents and
conventional adsorbents were made and it was concluded that non-conventional
adsorbents hold promise for effluent treatment. Non-conventional adsorbents can adsorb
phenol to the extent of 438.4 mg/g when contacted for a period of 2-48 hours in a pH range
of 4 to 6.
14. CHAPTER 3
METHODOLOGY
3.1 Preparation of the adsorbent
Sri Devi Cashew but Industry located in Karkala, was our primary source for the cashew
nut shells that were to be used as an adsorbent. Being located an hour away from the college
campus, the ease of availability and accessibility added to our advantage. Approximately 4
kilograms of cashew nut shells post oil extraction (African grade) were collected from the
industry. These shells were initially sun-dried for two complete days, after which they were
oven dried in the MT/MO laboratory at 100°C for a time span of 3 hours. The oven dried
shells were taken to the mechanical lab and incinerated in batches at 400°C for a time period
of 30 minutes per batch.
The shells obtained after incineration were roasted and hence made brittle for ease of
crushing. At first, the shells were crushed by hand with the use of a mortar-pestle. However,
the shells weren’t in the powdered form following the mortar-pestle and hence had to be put
in the mixer in order to attain very fine powdered adsorbent, which helps increase the
efficiency.
Figure 3.1.1: Raw cashewnut shells
16. 3.2 Characterization of the adsorbent
Characterization of the sample simply means finding out the different properties of the
sample in order to determine the usefulness of the cashew nut shell powder as an adsorbent.
Chemical treatment of any material is done in order to increase the carbon content in it. This
is done so to eventually reduce the amounts of volatile matter in the sample. Therefore,
before any tests were conducted an activated sample was prepared using sulphuric acid. 3
molal sulphuric acid was added to the sample such that it is in 1:1 ratio. The following was
kept in the oven present in the mas transfer laboratory for 6 hours at 70°C, after which it
was taken out and small amounts of water was added. The sample was kept back in the oven
for another 6 hours at the same temperature. The activated sample was then acquired which
was to be used for all proximate analysis of the adsorbent in order to evaluate the moisture
content, the volatile matter and the ash content.
(i) Moisture content in an adsorbent is nothing but the quantity of water contained
in the material. The higher the moisture content, the higher other qualities such
as pore volume and surface area of the particle would be.
(ii) Volatile matter is products given off by a material as a gas or vapour. In short,
it is substance that vaporises. A substance’s volatility is measure by its vapour
pressure; the point at which a substance turns from a solid to gas or vice-versa.
Volatile matter analysis is important in order to determine the overall usefulness
of the adsorbent.
(iii) Ash content, by definition includes all non-aqueous residues that remain after
a sample is burned. It includes the non-combustible matter.
The results for the proximate analysis are tabulated in Chapter 4, table 4.4.1.
3.3 FTIR analysis
Fourier transform infrared spectroscopy (FTIR) is a technique which is used to obtain an
infrared spectrum of absorption, emission, photoconductivity etc. of solid, liquid or a gas
sample. An FTIR spectrometer simultaneously collects high spectral resolution data over a
wide spectral range. This confers a significant advantage over an ordinary spectrometer
which measures intensity over a narrow range of wavelengths at a time.
The sample was handed over for FTIR analysis in the Department of Chemistry. The
resulting spectrum obtained displayed a series of peaks which are detailed in Chapter 4
under sub topic 4.3. This test often helps us determine the kinds of bonds present in the
sample, with the aid of the evident peaks in the various ranges of the wavelength.
17. 3.4 Preparation of the stock solution and the sample solutions
Stock solution is generally defined as a concentrated solution that is later diluted to lower
concentrations for actual use. Our concentrated solution being phenol, was a hard mixture
that required to be heated for about 45 minutes in order to melt it enough to liquid form. A
measured quantity of 1 ml of the melted phenol solution was added to 1 litre of distilled
water in a standard flask to create the stock solution. The solution as well agitated. Such
stock solutions are prepared to save preparation time, conserve materials, reduce storage
space and also to improve the accuracy with which working lower concentration solutions
are prepared.
Various proportions of the stock solution and distilled water was mixed to obtain six
different sample solution of 50 ppm, 100 ppm, 150 ppm, 200 ppm, 250 ppm and 300 ppm
respectively.
3.5 Calibration of sample solution
After the sample solutions of different concentrations were prepared, they were placed in a
UV spectrometer in the post graduate research lab to determine the absorbance of each of
those solutions of increasing concentrations. It was observed that the absorbance increases
with an increase in the concentration of the sample solution. By having more molecules
confined in the same volume, there is more material for a given frequency of light to be
absorbed in. The light is absorbed at a specific wavelength and this is because the electrons
in the chemical bonds only absorb certain wavelengths of light. Therefore, higher
concentration results in the presence of more bonds and hence, more electrons to absorb the
light. The results of the absorbance versus the concentration are tabulated in Chapter 4, table
4.4 and displayed in figure 4.4.
3.6 Optimization of conditions
The software Design-Expert was used to find the experiments which needed to be done for
the various range of conditions. The concentration of the solutions were taken as 100, 200
and 300 ppm respectively. The temperatures were taken to be 30, 40 and 50 degree Celsius
respectively. The adsorbent weights were 0.5, 1 and 1.5 grams respectively. In total there
were 20 experiments which needed to be conducted with the help of the software. The
percentage removal was calculated and was then cross referenced with the predicted values
from the software. The significant terms were shown by the software and the 3-D plots of
these terms were plotted. The graph of the predicted vs. actual values were also plotted. A
quadratic equation was derived by the software which can be used to find the percentage
removal at any of the parameters. Finally at the optimized conditions the experiment was
performed again and the error was calculated with respect to experimental and actual value.
All the plots, tables and graphs will related to optimization of conditions and are shown in
Chapter 4.
18. 3.7 Kinetic Studies
After optimizing the conditions, kinetic studies was carried out at those conditions. The
absorbance was calculated for every 10 minutes for the initial hour and after that for every
15 minutes for the next three hours. This experiment was performed three times and the
average values were taken. Q(mg/g) was calculated by (Co-Ct)*V/m. The respective
formulas and graphs were used to perform kinetic studies of 1st and 2nd order. The error bar
was plotted by finding the average of the three trials and the error implied was the standard
deviation in the positive and the negative ranges. R2 value were calculated from the graph
as well as the governing equations were established. The resulting plots, charts and
equations are tabulated and displayed in chapter 4.
3.8 Isotherm Studies
Isotherm studies were calculated at the optimized temperature and dosage values. However,
the concentration values were taken to be 100, 150, 200, 250 and 300 ppm respectively.
The experiments were carried out for 4 hours and finally, the absorbance was measured.
The experiments were performed 3 times and the average values were taken into
consideration for calculation purposes and for the plotting of the resulting graphs. The
isotherms that were taken into consideration include Langmuir, Freundlich and Temkin
isotherms. Appropriate equations and graphs were used to carry out these studies and
analysis was conducted after obtaining the results. The results are tabulated in chapter 4.
19. CHAPTER 4
RESULT ANALYSIS
4.1 Introduction
This chapter will include the tabulated results for each of the tests and experiments
performed over our project period. The various test results include: proximate analysis,
average particle size of the adsorbent, FTIR analysis, calibration of the sample solution,
optimization of the various parameters, kinetic and isotherm studies.
4.2 Proximate analysis
Table 4.2: Moisture content, volatile matter, ash content and fixed carbon percentages of
the samples
Sl. No. Tests Raw Sample Activated Sample
(i) Moisture Content (%) 10.9 14.3
(ii) Volatile Matter (%) 43.76 41.35
(iii) Ash Content (%) 15.16 13.23
(iv) Fixed Carbon (%) 30.18 31.12
The weights of the sample after heating for the specified time duration at respective
temperatures were noted down after subtracting the weight of the empty crucibles which
were found to be 10.317g (activated sample) and 10.535g (raw sample).
The moisture content of the activated sample was calculated to be greater than that of the
raw sample, which thus improves other qualities such as pore volume and surface area.
The volatile matter in the raw sample is greater than that of the activated sample which
proves the existence of small quantities of oil in the crushed cashew nut shells.
Ash content is the non-aqueous residues that is left behind after the sample is burned.
Theoretically the ash content of the activated sample should be less than that of the raw
sample which is justified by our obtained result. This confirms a reduced amount of non-
combustible matter in the activated sample.
4.3 FTIR analysis
FTIR is an acronym for Fourier Transform Infrared spectroscopy. This is a useful technique
that helps obtain infrared spectrum of absorption. It is an important tool to identify the
characteristic functional groups on the adsorbent surface. The prominent peaks obtained
from the activated sample are displayed in figure 4.3.
20. Figure 4.3: Infrared spectrum for the activated sample
The FTIR spectrum of the activated sample before adsorption shows a broad adsorption
peak at 3463.92 cm-1 corresponding to overlapping of –OH and –NH peaks. A peak at
2923.88 cm-1 represents the C-H group. The peak at 3606.64 cm-1 represents O-H stretch
(free hydroxyl) with functional groups of alcohols and phenols. The peaks at 1180.35 cm-1
and 1326.93 cm-1 represents C-H group with alkyl halides functional group and C-O stretch
with functional groups alcohols, carboxylic acids respectively.
4.4 Calibration of sample solution
Using the UV spectrometer, the absorbance of the various prepared sample solutions were
found. Table 4.4 displays how the absorbance varies with the concentrations and figure 4.4
displays the graph for the tabulated values.
21. Table 4.4: Absorbance of the various sample solutions
Concentration Absorbance
0 0
50 0.31
100 0.61
150 0.852
200 0.907
300 1
Figure 4.4: Absorbance vs. Concentration (ppm)
4.5 Optimization of Parameters
After using the design expert software, a list of experiments that had to be performed were
obtained, in order to optimise the conditions. The tabulated results are shown below in
Table 4.5.1.
0
0.2
0.4
0.6
0.8
1
1.2
0 50 100 150 200 250 300 350
Absorbance
Concentration (ppm)
Absorbance vs. Concentration
22. Table 4.5.1: Set experiments to be performed
Std Run Concentration
(ppm)
Dosage
(g)
Temperature
(°C)
Percentage removal
(%)
1 9 100 0.5 30 10
2 13 300 0.5 30 25
3 18 100 1.5 30 57
4 19 300 1.5 30 55
5 3 100 0.5 50 20
6 17 300 0.5 50 29.33
7 1 100 1.5 50 61
8 2 300 1.5 50 56.67
9 6 31.8 1 40 13.5
10 5 368.179 1 40 28.7
11 8 200 0.159 40 8.78
12 15 200 1.841 40 61.25
13 10 200 1 23.18 36.25
14 20 200 1 56.82 50
15 12 200 1 40 46
16 14 200 1 40 46.25
17 7 200 1 40 46.25
18 16 200 1 40 46
19 11 200 1 40 46
20 4 200 1 40 46
The variation in the percentage removal of phenol from wastewater with respect to various
parameters are displayed in figures 4.5.1, 4.5.2 and 4.5.3.
23. Figure 4.5.1: Percentage removal of phenol w.r.t Temperature and Concentration
Figure 4.5.2: Percentage removal of phenol w.r.t Temperature and Dosage
30
35
40
45
50
100
150
200
250
300
0
10
20
30
40
50
60
70
%removal
A: Concentration (mg/l)C: Temperature (C)
30
35
40
45
50
0.5
0.7
0.9
1.1
1.3
1.5
0
10
20
30
40
50
60
70
%removal
B: Dosage (g)C: Temperature (C)
24. Figure 4.5.3: Percentage removal of phenol w.r.t Dosage and Concentration
Table 4.5.2: Regression values with insignificant terms
Std. Dev 6.13 R-Squared 0.8944
Mean 39.75 Adj R-Squared 0.8746
C.V. % 15.43 Pred R-squared 0.7992
PRESS 1144.95 Adeq Precision 21.510
Table 4.5.3: Regression values without insignificant terms
Std. Dev 5.34 R-Squared 0.9499
Mean 39.75 Adj R-Squared 0.9049
C.V. % 13.44 Pred R-Squared 0.8183
PRESS 2176.58 Adeq Precision 16.309
0.5
0.7
0.9
1.1
1.3
1.5
100
150
200
250
300
0
10
20
30
40
50
60
70
%removal
A: Concentration (mg/l)B: Dosage (g)
25. The terms B, AB and A2 are the significant terms since percentage removal of phenol is greatly
dependent on them. The model equation for percentage removal of phenol from the software
was
𝟒𝟒. 𝟓𝟔 + 𝟏𝟕. 𝟓𝟒𝑩 − 𝟒. 𝟓𝟖𝑨𝑩 − 𝟕. 𝟎𝟓𝑨 𝟐
The optimised parameters provided by the software are displayed below with the predicted
percentage removal value and the experimental percentage removal value that was obtained
after performing the experiments at the displayed optimised conditions.
Table 4.5.4: Optimised conditions, predicted and actual percentage removal
Optimised Conditions
Concentration (mg/l) 176
Dosage (g) 1.499
Temperature (°C) 39.02
Predicted percentage removal (%) 61.006
Experimental percentage removal (%) 57.18
The percentage error was calculated by the following equation:
(
𝑷𝒓𝒆𝒅𝒊𝒄𝒕𝒆𝒅 − 𝑬𝒙𝒑𝒆𝒓𝒊𝒎𝒆𝒏𝒕𝒂𝒍
𝑷𝒓𝒆𝒅𝒊𝒄𝒕𝒆𝒅
)× 𝟏𝟎𝟎
Using the above formula, the percentage error was found to be 6.27%.
The software developed a set number of experiments that were to be performed and were
displayed in table 4.5.1. The predicted values developed by the software and the actual
experimental values are tabulated below, in table 4.5.5.
26. Table 4.5.5: Predicted vs. Actual values
Run order Actual value Predicted value Residual value
1 61.00 57.43 3.57
2 56.67 53.27 3.40
3 20.00 16.85 3.15
4 46 45.83 0.17
5 28.7 30.08 -1.38
6 13.5 20.83 -7.33
7 46.25 45.83 0.42
8 8.78 9.86 -1.08
9 10.00 7.25 2.75
10 36.25 42.91 -6.66
11 46 45.83 0.17
12 46 45.83 0.17
13 25.00 22.41 2.59
14 46.25 45.83 0.42
15 61.25 68.87 -7.62
16 46.00 45.83 0.17
17 29.33 31.01 -1.68
18 63.00 55.16 7.84
19 55.00 52.00 3.00
20 50.00 52.05 -2.05
The graph displaying the values of the predicted vs. the actual readings are displayed in
figure 4.5.4.
27. Figure 4.5.4: Predicted vs. Actual Readings
4.6 Kinetic Studies
Kinetic studies involves the study of first order, second order and intra-particle diffusion.
It includes calculation of regression values for each and an analysis of the best fit for our
experiment is conducted.
4.6.1 First Order:
First order kinetics is described by the following equation:
𝑳𝒐𝒈( 𝒒 𝒆 − 𝒒 𝒕) = 𝒍𝒐𝒈𝒒 𝒆 −
𝑲 𝟏
𝟐. 𝟑𝟎𝟑
× 𝒕
The adsorption process is a pseudo-first-order process. The first order rate constants (K1)
and qe are determined from the model. It was observed that the pseudo-first-order model
did fit well.
𝑸 = ( 𝑪 𝟎 − 𝑪𝒕) ×
𝑽
𝑴
Actual
Predicted
Predicted vs. Actual
0
10
20
30
40
50
60
70
0 10 20 30 40 50 60 70
28. Where C0 is the initial concentration, Ct is the instantaneous concentration at any particular
time, V is the volume of the solution and M depicts the mass of the adsorbent.
Table 4.6.1: Time vs. Average qe values
Time (mins) Average qe (mg/g)
10 0.444741
20 1.067378
20 1.200801
40 2.579497
50 3.424505
60 4.447409
75 5.64821
90 7.160329
105 8.272181
120 9.517456
135 10.76273
150 11.46942
165 12.05248
180 12.85301
195 13.0954
210 13.24216
225 13.3956
240 13.46142
For first order reaction, a plot of log (qe-qt) vs. time is plotted in order to find out the value
of the first order rate constant, which is established from the slope.
29. Figure 4.6.1: log(qe – qt) vs. Time
X axis of the above graph depicts time in minutes whereas the y axis depicts log(qe-qt).
The first order rate constant ‘k’, was calculated to be 0.021341 ± 0.000133 min-1.
From the graph, R2 value is found to be 0.8919.
4.6.2 Second order:
Second order kinetic studies is represented by the following equation:
𝒕
𝒒 𝒕
=
𝟏
𝒉
+
𝟏
𝒒 𝒆
× 𝒕
A plot of t/qt vs t is plotted and displayed in figure 4.6.2, to find the values of h and k. The
constant ‘h’ represents the inverse of the intercept and ‘k’ is the second order rate constant
(g/mgmin).
y = -0.0095x + 1.4828
R² = 0.8919
-2
-1.5
-1
-0.5
0
0.5
1
1.5
2
0 50 100 150 200 250
log(qe - qt) vs. Time
Error Bar
Linear (Error Bar)
Linear (Error Bar)
30. Figure 4.6.2: t/qt vs. Time
The x axis of the above graph represents time in minutes whereas the y axis represents t/qt.
The R2 value is established from the graph and is found to be 0.6263.
The h values is found to be 16.54767 mg/gmin and that of k is 0.000485 g/mgmin.
4.6.3 Intra-particle diffusion:
In order to gain insight into the mechanisms and rate controlling steps affecting the kinetics of
adsorption, the kinetic experimental results were fitted to intra-particle diffusion model. The
kinetic results were analysed by the intra-particle diffusion model to elucidate the diffusion
mechanisms, which is expressed by:
𝒒 𝒕 = 𝒌𝒊𝒅 × 𝒕 𝟏/𝟐
+ 𝑪
where C is the intercept and kid is the intra-particle diffusion rate constant (mg/gmin1/2), which
can be evaluated from the slope of the linear plot of qt vs. t1/2. The intercept of the plot reflects
the boundary layer effect. The larger the intercept, the greater the contribution of the surface
sorption in the rate controlling step. If the regression of qt vs. t1/2 is linear and passes through
R² = 0.6263
y = -0.0536x + 18.841
0
5
10
15
20
25
30
0 20 40 60 80 100 120 140 160
t/qt vs. Time
Error Bar 2nd order
Linear (Error Bar 2nd order)
31. the origin, then intra-particle diffusion is the sole rate-limiting step. However, with respect to
our project, this wasn’t the case and therefore it can be concluded that intra-particle diffusion
is not the only rate-limiting step.
Figure 4.6.3: qe vs. t0.5
4.7 Isotherm Studies
There are several models that have been reported in literature to show equilibrium
relationships between the adsorbent and the adsorbate. The Freundlich and Langmuir
models are the most frequently employed models. In this work, both these models with the
addition of Temkin models were used to describe the relationship between the amount of
phenol and its equilibrium concentrations.
4.7.1 Freundlich Isotherm
The linear form of the Freundlich isotherm is given by the relation:
𝑳𝒐𝒈𝒒 𝒆 = 𝑳𝒐𝒈(𝒌)+
𝟏
𝒏
𝑳𝒐𝒈(𝑪 𝒆)
y = 1.2289x - 4.3977
R² = 0.9804
-2
0
2
4
6
8
10
12
14
16
0 2 4 6 8 10 12 14 16 18
Qe(mg/g)
Time, t^0.5 (mins)
Qe vs. T^0.5
32. Where qe is the amount adsorbed at equilibrium (mg g-1), Ce is the equilibrium concentration
of the adsorbate (mg l-1), k and 1/n are the Freundlich constants related to adsorption capacity
and adsorption intensity respectively of the adsorbent. Freundlich isotherm constants were
determined from the plot of log qe vs. log Ce displayed in figure 4.7.1.
Figure 4.7.1: Log qe vs. Log Ce
From the obtained graph, the values for the Freundlich isotherm constants k and 1/n were
established to be 0.498 and 0.7 respectively.
The R2 value was determined from the graph above and is 0.976.
4.7.2 Langmuir Isotherm
The linear form of the Langmuir isotherm can be represented by the relation:
𝟏
𝑸 𝒆
= (
𝟏
𝑸 𝒎
) +
𝟏
( 𝑸 𝒎 × 𝑲 𝒂 × 𝑪 𝒆)
Where, Qe is the amount adsorbed at equilibrium (mg g-1), Qm (mg g-1) and Ka (L mg-1) are the
Languir constants related to the maximum adsorption and energy of adsorption respectively.
y = 0.7005x - 0.3027
R² = 0.976
0
0.2
0.4
0.6
0.8
1
1.2
1.4
0 0.5 1 1.5 2 2.5
Logqe
Log Ce
Freundlich Isotherm (Logqe Vs LogCe)
33. Langmuir isotherm constants were determined from plots of 1/Qe vs. 1/Ce as displayed in figure
4.7.2.
Figure 4.7.2: 1/Qe vs. 1/Ce
From the obtained graph, the values for the Langmuir isotherm constants Qm and Ka were
established to be 35.08772 mg g-1 and 0.0057 L mg-1 respectively.
The R2 value was determined from the graph above and is 0.9763.
4.7.3 Temkin Isotherm
Temkin isotherm contains a factor that explicitly takes into the account of adsorbent-adsorbate
interactions. Temkin isotherm can be represented by the relation:
𝑸 𝒆 = 𝑩𝒍𝒐𝒈( 𝑨) + 𝑩𝒍𝒐𝒈(𝑪 𝒆)
Where A is the Temkin isotherm equilibrium binding constant (L/g) and B is the constant
related to the heat of adsorption (J/mol).
Temkin isotherm constants were determined from the slope and the intercept of the plots of Qe
vs. logCe as displayed in figure 4.7.3.
y = 4.9997x + 0.0285
R² = 0.9763
0
0.02
0.04
0.06
0.08
0.1
0.12
0.14
0.16
0 0.005 0.01 0.015 0.02 0.025
1/Qe
1/Ce
Langmuir's Isotherm ( 1/Qe Vs 1/Ce)
34. Figure 4.7.3: Qe vs. Log Ce
From the obtained graph, the values for the Temkin isotherm constants ‘A’ and ‘B’ were found
to be 0.0493 L/g and 18.965 J/mol respectively.
The R2 value was determined from the graph and is 0.9379.
y = 18.965x - 24.791
R² = 0.9379
0
2
4
6
8
10
12
14
16
18
20
0 0.5 1 1.5 2 2.5
Qe
Log Ce
Temkin Isotherm ( Qe Vs Log(Ce) )
35. CHAPTER 5
CONCLUSION AND FUTURE SCOPE OF WORK
5.1 Conclusion
This work revolved around the usage of agricultural waste (cashewnut shells) to remove
phenol from wastewater. In order to obtain high efficiency and yield, it was necessary to
optimise the various parameters that were taken into consideration. There parameters
included concentration, dosage and temperature.
In this project, investigation of the equilibrium adsorption was carried out at the optimised
conditions developed by the software. The conditions included, concentration of 176 mg/l,
dosage of 1.499g and temperature of 39.02°C. At the optimised conditions, the predicted
percentage removal was 61.006% and the experimental percentage removal of phenol from
wastewater was 57.18%. Although the percentage removal value was close to the predicted
value, the variations are due to experimental errors.
Kinetic studies of first order, second order and intra-particle diffusion experiments were
conducted and it was found that the regression value of first order kinetic studies was the
closest to 1 and hence the best fit. In the case of intra-particle diffusion, theoretically, if the
regression line is linear and passes through the origin, then intra-particle diffusion is the
sole rate-limiting step. However, this wasn’t the case with the obtained graph from our
experiments and hence it can be concluded that intra-particle diffusion was not the only
rate-limiting step.
Alongside with kinetic studies, three isotherms were also studied, being Langmuir,
Freundlich and Temkin. From the result analysis, it was observed that the adsorption data
fitted into Langmuir, Freundlich and Temkin isotherms out of which Langmuir and
Freundlich adsorption models were found to have the highest regression values and hence
the best fit.
It can be concluded that cashewnut shells activated with sulphuric acid is a potential and
active adsorbent for the removal of phenol from wastewater.
5.2 Scope of Work
Cashewnut shells would make a decent adsorbent for the removal of phenol from
wastewater as it has assured 57.18% percentage phenol removal in this project. It will be
economical and also a contribution to recycling since the waste cashewnut shells which is
otherwise worthless, can now be grounded, dried and used as an adsorbent. The ease of
availability adds to its advantage. If not in large scale industries, for small scale industries,
recycling of water is possible to a large extent with the use of cashewnut shells.
36.
37. REFERENCES
Journal / Conference Papers
[1] Ihsan Habib Dakhil, “Removal of Phenol from Industrial Wastewater using Sawdust”,
Research Inventy: International Journal of Engineering and Science, volume 3, 2013,
pgs 25-28.
[2] M. Kermani and B. Bina, “Removal of Phenol from Aqueous solutions using Rice Husk
Ash and Activated Carbon, Pakistan Journal of Biological Sciences, 2006, pgs 1905-
1909.
[3] Mambo Moyo and Fidelis Chigondo, “Removal of Phenol from Aqueaous solution by
Adsorption on Yeast, Saccharomyces Cerevisiae”, Ijrras, volume 11, 2012, pgs 487-493.
[4] D K Singh and Bhavana Srivastava, “Removal of Phenol Pollutants from Aqueous
Solutions using various Adsorbents”, Journal of Scientific and Industrial Research,
volume 61, 2002, pgs 208-218.
[5] Patterson J W, cited in “Wastewater treatment technology” (Ann Arbor Science Ann
Arbor, Mic), Chapter 18, 1988, pg 205.
[6] Singh D K and Mishra A, “Removal of Phenolic compounds from water by iron loaded
marble”, Sep Sci Technol, 1993 (1923).
[7] Singh D K and Mishra A, “Removal of Phenolic coumpund from water using
chemically treated saw dust”, Indian J Environ Hlth, 32(1990) 345.
[8] Singh D K and Srivastava B, “Removal of some phenols by activate carbon developed
from used tea leaves”, J Ind Poll Cont, 16 (2000a) 19.
[9] Deshmukh S W and Pangarkar V G, “Recovery of organic chemicals from effluents by
adsorption over polymeric adsorbents”, Indian Chem Eng, 26 (1984) 35.
38. PROJECT DETAILS
Student Details
Student Name Kartik Kulkarni
Register Number 110903014 Section / Roll
No
8
Email Address kartikkulkarni2717@gmail.com Phone No (M) 9008769565
Student Name Varsha Sudheer
Register Number 110903248 Section / Roll
No
81
Email Address varshasudheer92@gmail.com Phone No (M) 9008744804
Project Details
Project Title REMOVAL OF PHENOL FROM WASTEWATER USING
AGRICULTURAL WASTE (CASHEWNUT SHELLS)
Project Duration Jan 2015 – May 2015 Date of
reporting
19.05.2015
Organization Details
Organization
Name
Full postal address
with pin code
Website address
Supervisor Details
Supervisor Name
Designation
Full contact address
with pin code
Email address Phone No (M)
Internal Guide Details
Faculty Name Mr C.R.Girish
Full contact address
with pin code
Department of Chemical Engineering,
Manipal Institute of Technology, Manipal – 576 104
(Karnataka State), INDIA
Email address cr.girish@manipal.edu