This document provides information from the Texas Department of Insurance on excavation safety. It discusses general requirements for excavations including locating underground utilities, providing access and egress from excavations, and protecting workers from hazards. It also covers soil classification and testing methods, as well as protective systems like sloping, benching, shoring, and shielding that can be used to prevent cave-ins. The document includes an excavation safety quiz and resources for additional training documentation.
Excavation and Trench Safety. Excavation and trenching are amongst the most dangerous operations in the construction industry. Dangers can include cave-ins, falling loads, hazardous atmospheres and hazards from using heavy equipment. Regular pre-work inspections can reduce hazards and serious risk of injury.
OSHA performance standard for trenching and excavation deals with many topics including soil classifications, underground hazards, atmospheric hazards, protection systems, competent person qualifications, etc. Our training covers all types of construction work. If you want to attend our classes, contact us by email at windsgroup@aol.com or call (732) 221-5687. More information can be obtained on our website. OSHA 10-Hr and 30-Hr.Construction Health and Safety courses are forming now.
Excavation and Trench Safety. Excavation and trenching are amongst the most dangerous operations in the construction industry. Dangers can include cave-ins, falling loads, hazardous atmospheres and hazards from using heavy equipment. Regular pre-work inspections can reduce hazards and serious risk of injury.
OSHA performance standard for trenching and excavation deals with many topics including soil classifications, underground hazards, atmospheric hazards, protection systems, competent person qualifications, etc. Our training covers all types of construction work. If you want to attend our classes, contact us by email at windsgroup@aol.com or call (732) 221-5687. More information can be obtained on our website. OSHA 10-Hr and 30-Hr.Construction Health and Safety courses are forming now.
Health and Safety Toolbox Talks are the quickest and most effective way to educate your construction workers in short bursts.
This toolbox talk gives you the information you need your staff to know to be able to work safely in and around excavations.
A must for all groundworkers, utility installers and any trade working on site during excavation work.
Construction is the industry mostly affected during monsoon season. Not only there are work delays but working in rain also cause some additional Health & Safety hazards. Some extra precautions must be taken to minimize the health risk during rainy season and workers should be trained to work during low visibility and slippery conditions.
Many construction site mishaps are caused by struck-by or caught against hazards. These hazards result from using mobile machinery and equipment and vehicles onsite. The hazards can be controlled and risks minimized by taking a few simple precautions and training/remind all site workers on these hazards. Everyone needs to be visible and out of the blind spots. Perimeter protection and spotters help with reduce injury, property damage, and maintain continuity. Vehicle and equipment maintenance and inspection are also equally important.
Health and Safety Toolbox Talks are the quickest and most effective way to educate your construction workers in short bursts.
This toolbox talk gives you the information you need your staff to know to be able to work safely in and around excavations.
A must for all groundworkers, utility installers and any trade working on site during excavation work.
Construction is the industry mostly affected during monsoon season. Not only there are work delays but working in rain also cause some additional Health & Safety hazards. Some extra precautions must be taken to minimize the health risk during rainy season and workers should be trained to work during low visibility and slippery conditions.
Many construction site mishaps are caused by struck-by or caught against hazards. These hazards result from using mobile machinery and equipment and vehicles onsite. The hazards can be controlled and risks minimized by taking a few simple precautions and training/remind all site workers on these hazards. Everyone needs to be visible and out of the blind spots. Perimeter protection and spotters help with reduce injury, property damage, and maintain continuity. Vehicle and equipment maintenance and inspection are also equally important.
While most scaffold-related accidents happen due to human factors, a percentage is caused due to improper scaffold construction. Below are essential guidelines in the proper construction of scaffolding
Between 2007 and 2011 there were three critical injuries involving mobile cranes at construction sites across Ontario, according to ministry reports. Some of these incidents occurred when cranes overturned and contacted electrical conductors or when the cranes or the material that they were lifting struck or crushed workers when the load was dropped.
Every year people are killed or seriously injured by collapses and falling materials while working in excavations. They are at risk from:
Excavations collapsing and burying or injuring people working in them;
material falling from the sides into any excavation; and
people or plant falling into excavations.
What are the main hazards in construction?
What are the main hazards in construction?
« Back to Table of Contents
Among the dangers in construction are:
•Falls from working at height,
•Crush injuries in excavation work,
•Slips and trips,
•Being struck by falling objects,
•Moving heavy loads,
•Bad working positions, often in confined spaces,
•Being struck or crushed by a workplace vehicle,
•Receiving injuries from hand tools,
•Inhalation of dust,
•Handling of rough materials,
•Exposure to dangerous substances (chemical and biological),
•Working near, in, or over water,
•Exposure to radiation,
•Loud noise,
•Vibration from tools or vibrating machinery.
IN 2015, OSHA proposed changes to the reporting requirements for all occupationally related injuries and illness. This presentation provides the updates to the regulatory requirements. If you have questions, feel free to contact us.
Construction Safety Training_Session 02_Excavation Works, Hazards and Controls Muizz Anibire
Learning objectives
Identify the various types of hazards in excavation works.
Describe the planning process for excavation works.
Describe basic excavation support systems.
Identify excavation control measures and precautions.
Occupational safety and health (OSH), also commonly referred to as occupational health and safety (OHS), occupational health, or occupational safety, is a multidisciplinary field concerned with the safety, health, and welfare of people at work (i.e. in an occupation). These terms also refer to the goals of this field, so their use in the sense of this article was originally an abbreviation of occupational safety and health program/department etc.
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...SOFTTECHHUB
The choice of an operating system plays a pivotal role in shaping our computing experience. For decades, Microsoft's Windows has dominated the market, offering a familiar and widely adopted platform for personal and professional use. However, as technological advancements continue to push the boundaries of innovation, alternative operating systems have emerged, challenging the status quo and offering users a fresh perspective on computing.
One such alternative that has garnered significant attention and acclaim is Nitrux Linux 3.5.0, a sleek, powerful, and user-friendly Linux distribution that promises to redefine the way we interact with our devices. With its focus on performance, security, and customization, Nitrux Linux presents a compelling case for those seeking to break free from the constraints of proprietary software and embrace the freedom and flexibility of open-source computing.
GridMate - End to end testing is a critical piece to ensure quality and avoid...ThomasParaiso2
End to end testing is a critical piece to ensure quality and avoid regressions. In this session, we share our journey building an E2E testing pipeline for GridMate components (LWC and Aura) using Cypress, JSForce, FakerJS…
In his public lecture, Christian Timmerer provides insights into the fascinating history of video streaming, starting from its humble beginnings before YouTube to the groundbreaking technologies that now dominate platforms like Netflix and ORF ON. Timmerer also presents provocative contributions of his own that have significantly influenced the industry. He concludes by looking at future challenges and invites the audience to join in a discussion.
Unlocking Productivity: Leveraging the Potential of Copilot in Microsoft 365, a presentation by Christoforos Vlachos, Senior Solutions Manager – Modern Workplace, Uni Systems
GraphSummit Singapore | The Art of the Possible with Graph - Q2 2024Neo4j
Neha Bajwa, Vice President of Product Marketing, Neo4j
Join us as we explore breakthrough innovations enabled by interconnected data and AI. Discover firsthand how organizations use relationships in data to uncover contextual insights and solve our most pressing challenges – from optimizing supply chains, detecting fraud, and improving customer experiences to accelerating drug discoveries.
Generative AI Deep Dive: Advancing from Proof of Concept to ProductionAggregage
Join Maher Hanafi, VP of Engineering at Betterworks, in this new session where he'll share a practical framework to transform Gen AI prototypes into impactful products! He'll delve into the complexities of data collection and management, model selection and optimization, and ensuring security, scalability, and responsible use.
Smart TV Buyer Insights Survey 2024 by 91mobiles.pdf91mobiles
91mobiles recently conducted a Smart TV Buyer Insights Survey in which we asked over 3,000 respondents about the TV they own, aspects they look at on a new TV, and their TV buying preferences.
Transcript: Selling digital books in 2024: Insights from industry leaders - T...BookNet Canada
The publishing industry has been selling digital audiobooks and ebooks for over a decade and has found its groove. What’s changed? What has stayed the same? Where do we go from here? Join a group of leading sales peers from across the industry for a conversation about the lessons learned since the popularization of digital books, best practices, digital book supply chain management, and more.
Link to video recording: https://bnctechforum.ca/sessions/selling-digital-books-in-2024-insights-from-industry-leaders/
Presented by BookNet Canada on May 28, 2024, with support from the Department of Canadian Heritage.
GraphRAG is All You need? LLM & Knowledge GraphGuy Korland
Guy Korland, CEO and Co-founder of FalkorDB, will review two articles on the integration of language models with knowledge graphs.
1. Unifying Large Language Models and Knowledge Graphs: A Roadmap.
https://arxiv.org/abs/2306.08302
2. Microsoft Research's GraphRAG paper and a review paper on various uses of knowledge graphs:
https://www.microsoft.com/en-us/research/blog/graphrag-unlocking-llm-discovery-on-narrative-private-data/
Communications Mining Series - Zero to Hero - Session 1DianaGray10
This session provides introduction to UiPath Communication Mining, importance and platform overview. You will acquire a good understand of the phases in Communication Mining as we go over the platform with you. Topics covered:
• Communication Mining Overview
• Why is it important?
• How can it help today’s business and the benefits
• Phases in Communication Mining
• Demo on Platform overview
• Q/A
Removing Uninteresting Bytes in Software FuzzingAftab Hussain
Imagine a world where software fuzzing, the process of mutating bytes in test seeds to uncover hidden and erroneous program behaviors, becomes faster and more effective. A lot depends on the initial seeds, which can significantly dictate the trajectory of a fuzzing campaign, particularly in terms of how long it takes to uncover interesting behaviour in your code. We introduce DIAR, a technique designed to speedup fuzzing campaigns by pinpointing and eliminating those uninteresting bytes in the seeds. Picture this: instead of wasting valuable resources on meaningless mutations in large, bloated seeds, DIAR removes the unnecessary bytes, streamlining the entire process.
In this work, we equipped AFL, a popular fuzzer, with DIAR and examined two critical Linux libraries -- Libxml's xmllint, a tool for parsing xml documents, and Binutil's readelf, an essential debugging and security analysis command-line tool used to display detailed information about ELF (Executable and Linkable Format). Our preliminary results show that AFL+DIAR does not only discover new paths more quickly but also achieves higher coverage overall. This work thus showcases how starting with lean and optimized seeds can lead to faster, more comprehensive fuzzing campaigns -- and DIAR helps you find such seeds.
- These are slides of the talk given at IEEE International Conference on Software Testing Verification and Validation Workshop, ICSTW 2022.
GDG Cloud Southlake #33: Boule & Rebala: Effective AppSec in SDLC using Deplo...James Anderson
Effective Application Security in Software Delivery lifecycle using Deployment Firewall and DBOM
The modern software delivery process (or the CI/CD process) includes many tools, distributed teams, open-source code, and cloud platforms. Constant focus on speed to release software to market, along with the traditional slow and manual security checks has caused gaps in continuous security as an important piece in the software supply chain. Today organizations feel more susceptible to external and internal cyber threats due to the vast attack surface in their applications supply chain and the lack of end-to-end governance and risk management.
The software team must secure its software delivery process to avoid vulnerability and security breaches. This needs to be achieved with existing tool chains and without extensive rework of the delivery processes. This talk will present strategies and techniques for providing visibility into the true risk of the existing vulnerabilities, preventing the introduction of security issues in the software, resolving vulnerabilities in production environments quickly, and capturing the deployment bill of materials (DBOM).
Speakers:
Bob Boule
Robert Boule is a technology enthusiast with PASSION for technology and making things work along with a knack for helping others understand how things work. He comes with around 20 years of solution engineering experience in application security, software continuous delivery, and SaaS platforms. He is known for his dynamic presentations in CI/CD and application security integrated in software delivery lifecycle.
Gopinath Rebala
Gopinath Rebala is the CTO of OpsMx, where he has overall responsibility for the machine learning and data processing architectures for Secure Software Delivery. Gopi also has a strong connection with our customers, leading design and architecture for strategic implementations. Gopi is a frequent speaker and well-known leader in continuous delivery and integrating security into software delivery.
GraphSummit Singapore | The Future of Agility: Supercharging Digital Transfor...Neo4j
Leonard Jayamohan, Partner & Generative AI Lead, Deloitte
This keynote will reveal how Deloitte leverages Neo4j’s graph power for groundbreaking digital twin solutions, achieving a staggering 100x performance boost. Discover the essential role knowledge graphs play in successful generative AI implementations. Plus, get an exclusive look at an innovative Neo4j + Generative AI solution Deloitte is developing in-house.
Essentials of Automations: The Art of Triggers and Actions in FMESafe Software
In this second installment of our Essentials of Automations webinar series, we’ll explore the landscape of triggers and actions, guiding you through the nuances of authoring and adapting workspaces for seamless automations. Gain an understanding of the full spectrum of triggers and actions available in FME, empowering you to enhance your workspaces for efficient automation.
We’ll kick things off by showcasing the most commonly used event-based triggers, introducing you to various automation workflows like manual triggers, schedules, directory watchers, and more. Plus, see how these elements play out in real scenarios.
Whether you’re tweaking your current setup or building from the ground up, this session will arm you with the tools and insights needed to transform your FME usage into a powerhouse of productivity. Join us to discover effective strategies that simplify complex processes, enhancing your productivity and transforming your data management practices with FME. Let’s turn complexity into clarity and make your workspaces work wonders!
Alt. GDG Cloud Southlake #33: Boule & Rebala: Effective AppSec in SDLC using ...James Anderson
Effective Application Security in Software Delivery lifecycle using Deployment Firewall and DBOM
The modern software delivery process (or the CI/CD process) includes many tools, distributed teams, open-source code, and cloud platforms. Constant focus on speed to release software to market, along with the traditional slow and manual security checks has caused gaps in continuous security as an important piece in the software supply chain. Today organizations feel more susceptible to external and internal cyber threats due to the vast attack surface in their applications supply chain and the lack of end-to-end governance and risk management.
The software team must secure its software delivery process to avoid vulnerability and security breaches. This needs to be achieved with existing tool chains and without extensive rework of the delivery processes. This talk will present strategies and techniques for providing visibility into the true risk of the existing vulnerabilities, preventing the introduction of security issues in the software, resolving vulnerabilities in production environments quickly, and capturing the deployment bill of materials (DBOM).
Speakers:
Bob Boule
Robert Boule is a technology enthusiast with PASSION for technology and making things work along with a knack for helping others understand how things work. He comes with around 20 years of solution engineering experience in application security, software continuous delivery, and SaaS platforms. He is known for his dynamic presentations in CI/CD and application security integrated in software delivery lifecycle.
Gopinath Rebala
Gopinath Rebala is the CTO of OpsMx, where he has overall responsibility for the machine learning and data processing architectures for Secure Software Delivery. Gopi also has a strong connection with our customers, leading design and architecture for strategic implementations. Gopi is a frequent speaker and well-known leader in continuous delivery and integrating security into software delivery.
Sudheer Mechineni, Head of Application Frameworks, Standard Chartered Bank
Discover how Standard Chartered Bank harnessed the power of Neo4j to transform complex data access challenges into a dynamic, scalable graph database solution. This keynote will cover their journey from initial adoption to deploying a fully automated, enterprise-grade causal cluster, highlighting key strategies for modelling organisational changes and ensuring robust disaster recovery. Learn how these innovations have not only enhanced Standard Chartered Bank’s data infrastructure but also positioned them as pioneers in the banking sector’s adoption of graph technology.
The Art of the Pitch: WordPress Relationships and SalesLaura Byrne
Clients don’t know what they don’t know. What web solutions are right for them? How does WordPress come into the picture? How do you make sure you understand scope and timeline? What do you do if sometime changes?
All these questions and more will be explored as we talk about matching clients’ needs with what your agency offers without pulling teeth or pulling your hair out. Practical tips, and strategies for successful relationship building that leads to closing the deal.
The Art of the Pitch: WordPress Relationships and Sales
Excavation safety
1. Texas Department
of Insurance
Excavation
Safety
Provided by
Division of
Workers’ Compensation
HS98-121C (7-06)
2. Contents
General Requirements __________________________________________________________________ 3
Introduction____________________________________________________________________________ 3
Definitions_____________________________________________________________________________ 3
Specific Requirements _________________________________________________________________ 3-4
Conclusion_____________________________________________________________________________ 4
Soil Classification ______________________________________________________________________ 4
Introduction____________________________________________________________________________ 4
Soil Mechanics _______________________________________________________________________ 4-5
Testing________________________________________________________________________________ 4
Manual Testing _____________________________________________________________________ 5
Dry Strength _______________________________________________________________________ 5
Thread Test ________________________________________________________________________ 5
Ribbon Test ________________________________________________________________________ 5
Thumb Penetration Test _______________________________________________________________ 5
Mechanical Devices _____________________________________________________________________ 5
Protective Systems _____________________________________________________________________ 6
Introduction____________________________________________________________________________ 6
Background ____________________________________________________________________________ 6
Requirements __________________________________________________________________________ 6
Sloping and Benching ____________________________________________________________________ 6
Shoring and Shield Systems _______________________________________________________________ 6
Shoring____________________________________________________________________________ 6
Shielding __________________________________________________________________________ 7
Final Safety Requirement _________________________________________________________________ 7
Excavation Safety Quiz__________________________________________________________________ 7
Test answers ___________________________________________________________________________ 8
Resources _____________________________________________________________________________ 8
Excavation Safety Training Documentation_________________________________________________ 9
Exhibits ___________________________________________________________________________ 10
Figure 1 - Simple Slope Excavation _________________________________________________________11
Figure 2 - Simple Bench Excavation_________________________________________________________11
Figure 3 - Hydraulic Shoring ______________________________________________________________12
2
3. General Requirements
Introduction
This guide will provide information on the Occupational hours advance notice. Give them as much lead time as
Safety and Health Administration’s (OSHA) general safety possible. When located, the utility must be physically
requirements for excavation work as published in 29 Code of and cautiously exposed.
Federal Regulations 1926 Subpart P. Once the utility is uncovered, it becomes your
responsibility to support, protect or have the utility
Definitions removed as necessary. Locating all buried utilities that
• Competent person - One who is capable of identifying
cross or parallel your route may be time-consuming,
existing and predictable hazards in the surroundings or
but failure to do so could have serious consequences.
working conditions which are unsanitary, hazardous, or
In Dallas, there are an average of 98 utility-crossings
dangerous to employees and who has authorization to
in a city block. The consequences of digging into a
take prompt corrective measures to eliminate them.
petroleum gas line or buried electrical utility could be
• Excavation - Any man-made cut, cavity, trench, or fatal but preventable.
depression made in the earth’s surface formed by earth
• Access and egress - Any trench or excavation four feet
removal.
or deeper must have a means of exit. Ladders and/or
• Registered Professional Engineer - Any person who by ramps must be located no more than 25 feet from any
education and training, having passed the requirements employee while he or she is in the excavation. Another
for registration, is registered as a professional engineer good safety practice is to ensure that ladders extend
in the state in which work is being performed. three feet above the surface of the excavation and be tied
• Trench - A narrow excavation made below the surface off if possible.
of the ground. In general the depth is greater than the • Exposure to vehicular traffic - Workers exposed to
width, but the width is no greater than 15 feet. vehicular traffic must wear “high visibility” vests or
• Trench shield - A structure that is able to withstand the clothing.
forces imposed on it by a cave-in and thereby protect • Exposure to falling loads - Under no condition should
workers within the structure. workers be permitted under loads handled by lifting
• Shoring - A structure such as a metal hydraulic, or digging equipment. Workers must stand away from
mechanical, or timber system that supports the sides of vehicles being loaded or unloaded. Vehicle operators
an excavation and is designed to prevent cave-ins. may stay in their vehicles during loading or unloading,
provided they are protected by a cab constructed in
Specific Requirements accordance with 29 CFR 1926.601(b)(6).
A basic rule for excavation is, “plan your dig, then dig your
• Warning systems - All mobile equipment (front-end
plan.” If you encounter something unplanned for, then stop
loaders, bulldozers and dump trucks) must be equipped
and replan.
with a warning device such as a backup alarm if the
Before you dig, know everything possible about the excava- operator does not have a clear and direct view of the
tion route. Have the route surveyed and mapped. Although edge of the excavation. Some other good safety practices
OSHA does not require soil borings, it is good engineering are use of hand signals from a flag person, stop logs,
practice to conduct soil borings to determine soil classes barricades or other mechanical signals. An attentive
along the route. A soil-boring log provides information on operator and a flag person who knows and uses proper
the water table and possible soil contamination from leaking hand signals provide the safest method.
under-ground storage tanks. • Hazardous atmospheres - In excavations deeper than
The following specific requirements for excavation are four feet with the potential for a hazardous atmosphere
found in 29 CFR 1926.651. or oxygen deficiency, conduct air testing before workers
enter the excavation and as often as necessary to ensure
• Surface encumbrances - includes trees, signs,
the atmosphere remains safe. Ventilation or respiratory
sidewalks, power poles, parking lots, and walls which
protection may be needed to protect workers from
must be removed, braced, shored, or otherwise supported
harmful atmospheres.
to prevent a hazard.
• Water accumulation hazards - Workers must not
• Underground utilities - such as sewer, water, gas lines,
work in excavations where water is accumulating
communications, and electric lines must be identified,
unless adequate precautions are taken to protect these
and physically located. Call the local area utility locator
workers from these hazards. This protection involves
company, give them the location or the route and depth
specific shoring, water removal (to control the level of
of the proposed excavation and request utility locations.
accumulating water), use of lifelines, harnesses, and
Usually the locator company requires a minimum of 48
careful monitoring by a competent person.
3
4. • Stability of adjacent structures - Excavation below a situation that could result in possible cave-ins,
the base or footing of a foundation, wall, sidewalk, indications of failure of the protective system, hazardous
pavement, or other structure is not permitted unless atmospheres, or other hazardous conditions. The
• shoring or bracing is provided to prevent cave-in inspections shall be done prior to start of work and as
• excavation is in stable rock often as needed throughout the shift. Inspections shall
be made after every rainstorm or other hazard-increasing
• a registered professional engineer determines the
occurrence.
structure is far enough away that the excavation is not
affected or that the excavation will not pose a threat When an inspection finds evidence of a situation that could
result in a hazard to the worker, exposed workers will be removed
to the workers
from the hazardous area until necessary precautions have been
• Loose rock and soil protection - Excavated earth made to ensure their safety.
(spoil), materials, tools, and equipment shall be placed
• Fall protection - Where personnel and/or equipment
no closer than two feet from the edge of the excavation.
must cross an excavation, a walkway or bridge shall be
Rock and soil should be scaled off the face of the
engineered to withstand the maximum expected load.
excavation or retained by shoring or other acceptable
methods to prevent the material from falling and striking The walkway or bridge shall be provided with standard
guardrails that meet OSHA standards outlined in 29 CFR 1926
workers.
Subpart M. All excavations in a remote location or unattended
Good work practice should dictate that no person will work should have adequate barriers or physical protection to prevent
on the sides of the slope or benched excavation above other people from falling into the excavation.
workers unless the lower workers are protected from falling
Upon completion, backfill all trenches, wells, pits, or shafts
materials. If possible and practical, grade the slope away from
as soon as practical.
the excavation. This serves a dual purpose of keeping equip-
ment and vehicles from accidentally rolling into the excavation Conclusion
and directing rain water away from the excavation Even with the introduction of new equipment and strict
OSHA 1926.100(a) requires the use of hard hats where there enforcement of OSHA standards, many workers die each year
is a possible danger of head injury from falling objects. Exca- and many more are seriously injured in trench accidents.
vation operations expose workers to these hazards in every Being buried alive is just one of the hazards of excava-
work zone during excavation. tion. This program covers only 9the general requirements of
• Inspections - A competent person must inspect the excavation safety. Following the safety measures listed in this
excavation and its support system for evidence of publication and not taking shortcuts will make a dangerous
job safer.
Soil Classification
Introduction
This section will provide information on soil mechanics, Soil types include:
procedures to reduce the possibilities of cave-ins during exca-
Type A soil - This is the most stable soil and is composed of
vation, identifying the four Occupational Safety and Health
clay, silty clay, clay loam and sandy clay. It has an unconfined
Administration (OSHA) soil classifications, and simple soil
compressive strength of 1.5 tons per square foot (t/sf) or greater.
identification tests and procedures.
Type A soil is very cohesive. Unfortunately, people wrongly
One cubic yard of dirt weighs an average of 2,700 pounds, assume it is stable and will not collapse if not shored.
and a cave-in is like dropping a small car from one foot above No soil, no matter the composition or apparent stability, can be
your head. To excavate and trench safely, you must know classified as Type A soil if the soil is fissured or subject to vibra-
about soil mechanics and how to slope and shore. Horizontal tion from traffic, equipment, or other excavation activities.
and vertical forces within the earth keep undisturbed soil in
place. An excavation disturbs or eliminates these forces. Soil Soil cannot be classed as Type A soil if layers dip into the
naturally moves downward and inward. A number of fac- excavation on a slope of four feet horizontal to one foot vertical
tors govern how fast this occurs, such as soil type, moisture, or there are other factors, such as seeping water, that would
vibration and surface loading. make the soil less than stable.
Type B soil - This cohesive soil is composed of silt, silty
Soil Mechanics
loam, sandy loam, and granular cohesive solids including
The type of soil governs the stability of the excavation.
angular gravel (crushed rock). It has an unconfined strength
OSHA requires that soil classification be made by a competent
greater than 0.5 tons per square foot but less than 1.5 tons
person and installation of adequate protective equipment be
per square foot.
made before workers enter the excavation.
4
5. Type C soil - Type C soil – This is the least stable soil. It Dry Strength
is a noncohesive soil composed of granular soils, including If the soil is dry and crumbles on its own or with moderate
sand, gravel, loamy sand, submerged soil or soil from which pressure into individual grains or fine powder, it is granular
water is draining, submerged rock, or soil in a sloped layered (any combination of gravel, sand or silt). If the soil is dry and
system where the layers dip into the excavation at a slope of falls into clumps which break up into smaller clumps, but
four feet horizontal to one foot vertical or greater. It has an the smaller clumps can only be broken up with difficulty, it
unconfined compressive strength of 0.5 tons per square foot may be clay in any combination with gravel, sand or silt. If
or less. the dry soil breaks into clumps which do not break up into
Stable rock - This natural solid mineral material can small clumps and which can only be broken with difficulty,
be excavated with vertical sides and remains intact while and there is no visual indication the soil is fissured, the soil
exposed. may be considered unfissured.
Thread test (plasticity)
Testing
This determines whether a sample is cohesive. Roll a sample
When making a site soil classification, the competent person
of the soil between the palms of your hands to about one-eighth
conducts both visual and manual tests. Factors to examine
inch diameter thread at least several inches long.
are:
Place the rolled soil thread on a flat surface and pick up by
• Soil particle size - Usually there is a mixture of sizes.
one end. If the sample holds together for two inches without
The percentage of sand to silt and clay determines the
breaking, it is considered cohesive.
soil type.
• Grain size - If a grain of soil is larger than a #2 pencil Ribbon Test
lead, it is classified as gravel. If it is smaller, but can be This is another test for cohesiveness and is used as a back-up
seen by the unaided eye, it is classified as sand. Clay test for the thread test. Roll a representative soil sample into
and silt particles cannot be seen without the use of a a cylinder about three-fourths inch in diameter and several
microscope. A general statement is the larger the grain inches in length. Then squeeze this sample between thumb
size the less stable the soil. and forefinger into a flat unbroken ribbon one-fourth to one-
eighth inch thick, which is allowed to fall freely over the
• Soil that clumps and holds together when dug out is
fingers. If the ribbon does not break off before several inches
most likely to be clay or silt.
are squeezed out, the soil is considered cohesive.
• Cracks in walls of the excavation, with material spilling
off (slabs of soil falling off the sides) indicates Type B or Thumb Penetration Test
C soil. The thumb penetration test estimates the unconfined com-
• Standing water or water seeping out of the bottom or pressive strength of cohesive soils and is based on testing
trench walls automatically classifies the soil as Type C. described in the American Society for Testing and Materials
• Layered soil adjacent to roadways or buildings, disturbed (ASTM) standard D2488. Take a soil sample collected from a
soil, or soil exposed to a source of vibration, requires a freshly dug soil clump from the spoil pile. Press your thumb
soil classification to be made by a registered professional against the sample. If the sample is readily indented by your
engineer. thumb but penetration can be done only by using great effort,
then the soil is classified as Type A. If penetration occurs to
Manual Testing
the base of the thumb nail and is accomplished with moderate
Protective system requirements are based on the results of
difficulty, then it is Type B. If the sample can be penetrated
testing. Never enter an unprotected excavation to obtain a
easily several inches by the thumb, and if it can be molded
soil sample. Take the soil sample from freshly dug material
by light finger pressure, then the soil is Type C. Drying the
in the spoil pile. The tests should be done as soon as possible
sample can greatly influence the results of this test. Perform
to preserve the sample’s natural moisture.
this test immediately after taking the sample.
Mechanical Devices
Mechanical devices for determining soil type include the
pocket penetrometer and the hand-operated vane shear pen-
etrometer. Operation of the device and interpretation of the
results are found in the manual or literature furnished by
the manufacturer of these devices. For a complete discus-
sion of soils and testing, refer to the 29 CFR 1926 Subpart
P, Appendix A.
5
6. Protective Systems
Introduction
This section will provide information on protective sys- When these factors are present the excavation, whether
tems used to reduce the possibilities of fatalities and injuries benched or sloped, must be re-inspected for signs of dis-
from cave-ins during excavations. Information on sloping and tress.
benching techniques for every soil type and methods of using
Distress signs include:
shoring and trench box equipment will also be provided.
• Cracking excavation walls;
Background
• Cracks in the surface soil 1/2 to 3/4 the distance back
Except in stable rock, the Occupational Safety and Health from the excavation as the excavation is deep;
Administration requires workers to be protected against the
danger of cave-ins in trenches and/or excavations that are five • Bulging of the trench wall; and
feet or deeper. There are four recognized methods of protec- • Sloughing off of clods or small sections from the trench
tion: sloping, benching, shoring and shielding (trench box). wall.
The use of any of these methods or combinations of these
All of these indicate an imminent danger of cave-in. If any
methods are governed by factors such as space, soil types,
of these signs are observed, employees shall be directed to
depth, speed, and expense.
evacuate the excavation and the slope shall be cut back further
Requirements or a mechanical protective system installed.
OSHA states, “each employee in an excavation shall be
Shoring and Shield Systems
protected from cave-ins by an adequate protective system.”
Shoring and shield systems are protective measures that
There are only two exceptions when a protective system is
add support to an excavation.
not required: (1) excavation made entirely in stable rock; or (2)
excavation less than five feet deep which has been examined The safest system is one that can be installed and removed
by a competent person who determined there is no indication without personnel entering the excavation.
for a potential cave-in. Shoring
Sloping and Benching This system is designed to prevent excavation failure (cave-
Sloping is a protective measure that cuts the walls of the ins) by supporting trench walls with a system of vertical
excavation back at an angle from the floor to produce a stable uprights and/or sheeting and Cross braces (shores). Shores are
slope. The slope angle is based on soil type. The flatter the angle structures that cross the trench and put pressure on the vertical
of the slope, the greater the protection factor for the employee uprights and sheeting (see Figure 3). Shoring methods range
(see Figure 1). from timber shoring to aluminum hydraulic devices that bear
• Type A Soil: The ratio is 3/4 ft. horizontal for every foot directly on the wall of the trench and transmit approximately
vertical (53° from the horizontal) 1500 pounds per square inch (psi) of pressure to pre-load the
soil. This pressure preloading produces the so called “arch
• Type B Soil: The ratio is 1 ft. horizontal for every foot effect” that stabilizes the trench wall and prevents a cave-
vertical (45° from the horizontal) in. Information on timber shoring methods can be obtained
• Type C Soil: The ratio is 11/2 ft. horizontal for every one from 29 CFR 1926, Subpart P, Appendix C. Appendix D has
foot vertical (34° from the horizontal) information for aluminum hydraulic shoring.
Benching is the process of cutting benches or steps into Some safety requirements for using aluminum hydraulic
the excavation (see Figure 2). The angle used for benching shoring are as follows:
is based on a ratio of horizontal to vertical cuts. It should be • Installation and removal of the shoring is done from
noted that benching is reserved only for cohesive soils. outside of the excavation.
It is not permissible to bench Type C soil because of its • Individual shores (elements) are pressurized and depres-
inability to support a vertical wall. Type C soils always require surized slowly to prevent failure of the remaining shores
the use of sloping, shielding, or shoring. or collapse of the excavation walls.
Factors like these make soil less stable: • Data provided by the manufacturer is tabulated and
• Vibration from machinery or traffic; designed by a registered professional engineer (PE).
• Exposure to rain or flooding; This information and procedures for use must be followed
regardless of soil classifications. Any modification must be
• Periods of low humidity (drying); and
made by a registered professional engineer and approved in
• Soil loading from overburden or equipment. writing and sealed.
6
7. Shielding
A trench shield is an engineered metal box that is placed • Workers shall not be allowed inside the shield or to ride
in the excavation. It does not provide structural strength to on the shield, when the shield is being installed, removed
the excavation, but provides workers a safe worksite that pro- or moved vertically.
tects them from collapsing material. A registered professional
• Shield structure shall extend a minimum of 18 inches
engineer must design the trench shield or trench box system
above the lip of the excavation when used in conjunction
which can be premanufactured or built on site as necessary.
with a sloped or benched excavation.
Regardless of where they are built, they must be constructed
to exact engineering specifications. There are several safety • Excavation may be permitted up to a depth of 2 feet below
requirements when using a trench box: the bottom of the shield provided the shield is designed to
resist the forces calculated for the full depth of the trench
• Shields must be installed in a manner that restricts side-
and there is no indication while the trench is open of a
to-side movement or any other hazardous movement in the
possible collapse of soil from behind or below the bottom
event of sudden lateral movement, i.e., trench failure.
of the shield.
• The shield system shall not be exposed to loads exceeding
the design standard. Final Safety Requirement
All excavations must be backfilled as soon as possible after
• Workers shall be protected from the hazards of cave-
removal of the support system. No worker is permitted in an
ins when entering or leaving the area protected by the
unshored or unprotected excavation or trench no matter how
shield.
compelling the reason.
Excavation Safety Quiz
Name: _______________________________ a. Type A soil
b. Type B soil
Department: __________________________ c. Type C soil
Date: ________________________________ d. stable rock
Employee or SSN: ______________________ 6. OSHA requires a ladder or ramp to exit a trench if the
Circle the letter indicating the correct answer. depth of excavation is _____.
1. A stairway, ladder, ramp or other safe means of egress a. 3 feet
shall be located in trench excavations that are 4 ft. (1.22 b. 4 feet or more
m) or more in depth so as to require no more than______ c. 6 feet
feet of lateral travel for employees. d. 12 feet
a. 10
7. The least stable soil type is _____.
b. 25
a. Type A
c. 50
b. Type B
d. none of the above
c. Type C
2. The thumb penetration test is based on _____. d. stable rock
a. OSHA table Z-1 8. One advantage of aluminum hydraulic shoring is that
b. NFPA workers do not have to enter an unprotected trench to
c. ASTM D2488 install or remove it.
d. not listed a. True b. False
3. In excavations less than five feet deep, no shoring is
required if _____. 9. When excavating under the base of a wall, foundation
4. In Type B soil, the sloping ratio is _____. or sidewalk, the support system must be designed by a
registered professional engineer.
a. 3/4 to 1.
b. 1 to 1. a. True b. False
c. 1-1/2 to 1. 10. A trench shield (trench box) must be designed by a
d. not permitted a. competent person
5. Excavations with vertical walls that remain intact b. machinist
when exposed are in _____. c. registered professional engineer
d. certified welder
7
8. Test Answers:
1. b
2. c
3. d
4. b
5. d
6. b
7. c
8. a
9. a
10 c
Resources
“Excavations.” Code of Federal Regulations Title 29, Pt. 1926, Subpt. P, September 1, 2000 ed.
8 Hour Competent Person Student Manual, Speed Shore Corporation, 1993
OSHA 2226, Excavations, Occupational Safety and Health Administration, 2000 (Reprinted)
8
9. Excavation Safety Training
The following people have attended training on the excavation safety program on:
Name Signature Employee #
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
_____________________ _____________________ ___________________
Training conducted by__________________________
Signature ____________________________________
Title ________________________________________
9
11. Figure 1
Simple Slope Excavation
Class Measurement Degrees
Class A 3⁄4: 1 53°
Class B 1:1 45°
Class C 11⁄2:1 34°
C B A A B C
Figure 2
Simple Bench Excavation
Type A Soil
20’ Maximum 1
3/4
4’ Max
11