The document discusses a study that evaluated the use of Descriptive Waypoints (DWs) to help pilots perform Continuous Descent Approaches (CDA) more consistently. Twelve pilots flew simulated CDA approaches with 1, 3, or 5 DWs under different wind conditions. The results showed that having more DWs decreased altitude deviations from the targets and increased pilot feedback that DWs were useful for strategizing corrections. The pilots recommended integrating DWs into existing charts. The study suggests DWs can enhance pilot ability to perform CDA and are a potential near-term solution to improve CDA procedures.
This document proposes integrating trajectory-oriented air traffic management with airborne separation assistance systems. It describes today's sector-oriented air traffic control system and proposed strategic trajectory-based approaches. The concept integrates these by generating conflict-free trajectories meeting time constraints, while allowing aircraft to maintain local spacing using airborne systems when needed. This combines benefits of both approaches. The concept could be implemented incrementally using emerging technologies and procedures. Research is still needed to further develop and evaluate integrating trajectory planning with airborne separation assistance.
Enhancing Pilot Ability to Perform Continuous Descent Approach with Descript...Michael LaMarr
This document summarizes research on using descriptive waypoints to help pilots perform continuous descent approaches more accurately. It describes a study that tested different numbers of descriptive waypoints under varying wind conditions. The results showed that using five descriptive waypoints provided the most structure for pilots and kept aircraft closest to their altitude and speed targets at each waypoint. Pilots also provided feedback that integrating descriptive waypoints into charts and displays could help them manage vertical speed and intercept targets more easily. Future research areas include integrating descriptive waypoints with advanced cockpit systems and using them for traffic and terrain avoidance.
This document summarizes a study on improving predictability in airport surface operations using a decision support tool called SARDA (Spot and Runway Departure Advisor). The study used data from simulations testing SARDA to measure predictability from three perspectives: air traffic controllers, flight operators, and traffic management. Survey results from controllers indicate SARDA reduced unexpected workload surges and attention needed for managing scheduled flights. Analysis of taxi times found SARDA reduced variability and uncertainty in taxi-out times. SARDA also enabled more accurate predictions of take-off times. Overall, the results suggest SARDA has the potential to improve predictability in airport surface operations.
Design & application of cdo for ahmedabad airport within ahmedabad tmaARVIND KUMAR SINGH
ICAO has emphasized on aviation safety, air navigation capacity and efficient environmental protection by strategic objective. ICAO also focused on the development and implementation on PBN, CDO and CCO for sustainable growth of aviation. Global Air Navigation Plan (2013-2028) provides methodology for integrated aviation planning and increased importance of collaborations and partnership among stakeholders. GANP outlined the implementation issues involving the PBN all over the world. In line with ICAO objective, this focuses on CDO procedure at Ahmedabad airport.
Trial CDO has been implemented but no formal procedure for airlines operator has yet been promulgated at various Indian airports including Ahmedabad Airport. Area and Approach are physically located at same place and trained controllers provide these services on rotation basis at Ahmedabad airport. Air Traffic Services provided with surveillance tools. STARs and SIDs were introduced in year 2008 at Ahmedabad Airport. Ahmedabad Airport has medium density traffic of aircraft movement, average 150 schedule aircraft movement per day and approx 75 scheduled arrivals per day. Due to non availability of published procedure limited Continuous Descent Operations are being performed by the arrivals, at Ahmedabad Airport.
This emphasises on analysis of traffic pattern on arrival routes for possible implementation of CDO is existing arrival procedures and study of existing CDO procedure, analysis of cost benefit, fuel efficiency and carbon emission for Ahmedabad airport.
Design & Application of Continuous Descent Operation (CDO) procedure in Ahmedabad TMA for Ahmedabad Airport will provide more efficient airspace & arrival routes, reduction in pilot –controller work load, cost saving to airlines operators and environmental benefits through reduced fuel burn.
With good CDO procedure, initially minimum 65% of arrivals are expected to perform CDO at Ahmedabad leading to saving of cost of operations and carbon emission, in addition to brand and image building of AAI as ANSP at Ahmedabad. The experience gained will also help AAI extend such procedure to other medium to light density traffic airports and subsequently all airports in line with ICAO Guidelines and requirement.
- The document discusses the problem of optimally loading cargo containers onto an aircraft in an automated manner.
- Key considerations include balancing the aircraft's load distribution to minimize fuel consumption while satisfying safety and stability requirements.
- A mathematical model is presented that formulates the problem as an integer linear program to determine the optimal allocation of containers to aircraft compartments. The objective is to maximize the total loaded mass within constraints on compartment capacities and the aircraft's center of gravity.
- Variables, constraints, and an objective function are defined to represent the load balancing problem in a form that can be solved using integer linear programming techniques.
This document discusses the conceptual design, structural analysis, and flow analysis of an unmanned aerial vehicle (UAV) wing. It begins by providing background on UAVs and listing the design requirements and parameters for the wing. It then describes selecting a rectangular wing planform and NACA 2415 airfoil based on the design criteria. Aerodynamic analysis is conducted to determine performance parameters like lift coefficient and drag. Structural analysis of the wing is performed using two spar designs - a tubular spar with and without a strut. Maximum stresses and bending moments are calculated and compared for straight and tapered wing configurations. Flow simulation will also be conducted on the finalized wing design.
The document discusses key aspects of ICAO's Annex 14, which provides standards and recommended practices (SARPs) for aerodrome design and operations. It outlines the objectives and methodology for understanding Annex 14 SARPs. It describes the development and amending process of SARPs and the contents and structure of Annex 14, including the aerodrome reference code system and different types of approaches. It also summarizes important SARPs regarding physical characteristics like obstacle limitation surfaces, markings, lighting, and signs.
Air Traffic Control and Runway SeparationsAshwin Samales
This document discusses air traffic control and runway separations at airports. It explains that air traffic control provides operating rules for airports and influences airport capacity. Different types of air traffic control equipment are located at airports, including navigation, communication, surveillance and weather equipment. The document discusses siting criteria and critical areas for some of these equipment. It also provides examples of minimum separations between aircraft on runways and approaches under instrument and visual meteorological conditions.
This document proposes integrating trajectory-oriented air traffic management with airborne separation assistance systems. It describes today's sector-oriented air traffic control system and proposed strategic trajectory-based approaches. The concept integrates these by generating conflict-free trajectories meeting time constraints, while allowing aircraft to maintain local spacing using airborne systems when needed. This combines benefits of both approaches. The concept could be implemented incrementally using emerging technologies and procedures. Research is still needed to further develop and evaluate integrating trajectory planning with airborne separation assistance.
Enhancing Pilot Ability to Perform Continuous Descent Approach with Descript...Michael LaMarr
This document summarizes research on using descriptive waypoints to help pilots perform continuous descent approaches more accurately. It describes a study that tested different numbers of descriptive waypoints under varying wind conditions. The results showed that using five descriptive waypoints provided the most structure for pilots and kept aircraft closest to their altitude and speed targets at each waypoint. Pilots also provided feedback that integrating descriptive waypoints into charts and displays could help them manage vertical speed and intercept targets more easily. Future research areas include integrating descriptive waypoints with advanced cockpit systems and using them for traffic and terrain avoidance.
This document summarizes a study on improving predictability in airport surface operations using a decision support tool called SARDA (Spot and Runway Departure Advisor). The study used data from simulations testing SARDA to measure predictability from three perspectives: air traffic controllers, flight operators, and traffic management. Survey results from controllers indicate SARDA reduced unexpected workload surges and attention needed for managing scheduled flights. Analysis of taxi times found SARDA reduced variability and uncertainty in taxi-out times. SARDA also enabled more accurate predictions of take-off times. Overall, the results suggest SARDA has the potential to improve predictability in airport surface operations.
Design & application of cdo for ahmedabad airport within ahmedabad tmaARVIND KUMAR SINGH
ICAO has emphasized on aviation safety, air navigation capacity and efficient environmental protection by strategic objective. ICAO also focused on the development and implementation on PBN, CDO and CCO for sustainable growth of aviation. Global Air Navigation Plan (2013-2028) provides methodology for integrated aviation planning and increased importance of collaborations and partnership among stakeholders. GANP outlined the implementation issues involving the PBN all over the world. In line with ICAO objective, this focuses on CDO procedure at Ahmedabad airport.
Trial CDO has been implemented but no formal procedure for airlines operator has yet been promulgated at various Indian airports including Ahmedabad Airport. Area and Approach are physically located at same place and trained controllers provide these services on rotation basis at Ahmedabad airport. Air Traffic Services provided with surveillance tools. STARs and SIDs were introduced in year 2008 at Ahmedabad Airport. Ahmedabad Airport has medium density traffic of aircraft movement, average 150 schedule aircraft movement per day and approx 75 scheduled arrivals per day. Due to non availability of published procedure limited Continuous Descent Operations are being performed by the arrivals, at Ahmedabad Airport.
This emphasises on analysis of traffic pattern on arrival routes for possible implementation of CDO is existing arrival procedures and study of existing CDO procedure, analysis of cost benefit, fuel efficiency and carbon emission for Ahmedabad airport.
Design & Application of Continuous Descent Operation (CDO) procedure in Ahmedabad TMA for Ahmedabad Airport will provide more efficient airspace & arrival routes, reduction in pilot –controller work load, cost saving to airlines operators and environmental benefits through reduced fuel burn.
With good CDO procedure, initially minimum 65% of arrivals are expected to perform CDO at Ahmedabad leading to saving of cost of operations and carbon emission, in addition to brand and image building of AAI as ANSP at Ahmedabad. The experience gained will also help AAI extend such procedure to other medium to light density traffic airports and subsequently all airports in line with ICAO Guidelines and requirement.
- The document discusses the problem of optimally loading cargo containers onto an aircraft in an automated manner.
- Key considerations include balancing the aircraft's load distribution to minimize fuel consumption while satisfying safety and stability requirements.
- A mathematical model is presented that formulates the problem as an integer linear program to determine the optimal allocation of containers to aircraft compartments. The objective is to maximize the total loaded mass within constraints on compartment capacities and the aircraft's center of gravity.
- Variables, constraints, and an objective function are defined to represent the load balancing problem in a form that can be solved using integer linear programming techniques.
This document discusses the conceptual design, structural analysis, and flow analysis of an unmanned aerial vehicle (UAV) wing. It begins by providing background on UAVs and listing the design requirements and parameters for the wing. It then describes selecting a rectangular wing planform and NACA 2415 airfoil based on the design criteria. Aerodynamic analysis is conducted to determine performance parameters like lift coefficient and drag. Structural analysis of the wing is performed using two spar designs - a tubular spar with and without a strut. Maximum stresses and bending moments are calculated and compared for straight and tapered wing configurations. Flow simulation will also be conducted on the finalized wing design.
The document discusses key aspects of ICAO's Annex 14, which provides standards and recommended practices (SARPs) for aerodrome design and operations. It outlines the objectives and methodology for understanding Annex 14 SARPs. It describes the development and amending process of SARPs and the contents and structure of Annex 14, including the aerodrome reference code system and different types of approaches. It also summarizes important SARPs regarding physical characteristics like obstacle limitation surfaces, markings, lighting, and signs.
Air Traffic Control and Runway SeparationsAshwin Samales
This document discusses air traffic control and runway separations at airports. It explains that air traffic control provides operating rules for airports and influences airport capacity. Different types of air traffic control equipment are located at airports, including navigation, communication, surveillance and weather equipment. The document discusses siting criteria and critical areas for some of these equipment. It also provides examples of minimum separations between aircraft on runways and approaches under instrument and visual meteorological conditions.
1. The document lists Key Performance Parameters (KPPs) and additional system requirements for an Advanced Pilot Training (APT) system. The KPPs include thresholds and objectives for aircraft and simulator availability, sustained G-forces, and simulator visual acuity and performance fidelity.
2. Additional requirements address maneuverability, weapons employment simulation, data links, angle of attack, turn rates, debriefing capabilities, and open systems architecture. Space, weight, power, and cooling growth provisions must also be included.
3. Scenario input is required for both aircraft and simulators to support tactical training, and the aircraft design should enable future in-flight refueling capability.
The document discusses the factors that influence airport runway configuration and layout. The four basic runway configurations are single runway, parallel runways, open-V runways, and intersecting runways. Runway layout is determined by operational capacity needs, environmental concerns, terrain, weather patterns, and the types of aircraft using the airport.
The document discusses the design of modern airports, using Rajiv Gandhi International Airport (RGIA) in Hyderabad, India as a case study. RGIA was built as a public-private partnership between 2004-2008 to replace Begumpet Airport. It has one passenger terminal built on 5,400 acres that can currently handle 12 million passengers annually, with plans to expand capacity to 40 million. Key components discussed include the single runway, taxiways, parking areas, and precision lighting to aid pilots on approach. The terminal building incorporates green building practices and was completed in a record 28 months.
This document provides details of an aircraft design project for a new personal jet called "The Flash" being designed by Kent Aerospace. It includes sections on requirements analysis, technical design, manufacturing plan, regulatory compliance, program management, finance, marketing, and socioeconomic impacts. The technical design section provides details on sizing methodology, assumptions, wing and tail geometry, thrust-to-weight ratio, powerplant specifications, wing loading data, and performance results. The design utilizes twin DGEN 380 turbofan engines from Price Induction and is intended to carry 3 passengers up to 800 nautical miles at a cruise speed of 230 knots.
Conceptual Design of a Light Sport AircraftDustan Gregory
The document provides a conceptual design for a light sport aircraft. It defines key parameters for light sport aircraft and summarizes the design of several existing models. The design process described initializes parameters like wing area and airfoil selection. Equations are presented to calculate performance metrics like drag, power required, climb rate, endurance and range. Requirements for the conceptual design are specified, including taking off, cruising, and landing with sufficient fuel reserves.
This document is a project report submitted by S Niranjan Varma for a Bachelor of Technology degree in Civil Engineering. It discusses airport planning and design. The report includes an introduction to airport surveys conducted for planning, such as topographical, drainage, soil and meteorological surveys. It also covers runway orientation factors like wind conditions. The project involves designing the airside area including the runway, taxiway and apron. It includes designing the terminal building using software and calculating loads and structural elements. The landside area plan and calculations are also presented. The conclusion summarizes the project and references are provided.
This presentation briefly explains about important factors affecting the design and plan of Airports.
Topics Covered: Introduction, AAI, Features of planes affecting the design of airports, size of airport, site selection for airport, visual aids, difficulries in planning an airport.
This thesis analyzes the aerodynamic performance of a canard-configured forward swept wing aircraft design. Canards are small wings mounted in front of the main wing that act as horizontal stabilizers to control pitch. A forward swept wing directs airflow inward from the wingtips toward the root. The study selects airfoils for the canards, wing root, and wing tip based on criteria to induce earlier stalling at the root than the tips. Graphs of lift, drag, and moment coefficients versus angle of attack are presented for the reference design and two experimental airfoil sets. The second set is chosen for its larger gaps in stalling angles and higher maneuverability potential. In conclusion, a canard-configured forward
The document analyzes the stability and control of the Zivko Edge 540T aerobatic aircraft. It estimates key physical properties and determines equilibrium flight conditions. Non-dimensional stability derivatives are then calculated, showing the aircraft is longitudinally stable. Lateral stability is also analyzed, with the aircraft found to be laterally stable except for an unstable spiral mode. Dimensional derivatives are used to examine specific stability modes, with most modes stable except the spiral mode.
EGS Weight & Balance Services provides aircraft load control and performance engineering services. Led by Managing Director Eric Bahn, EGS has over 20 years of experience in operations management, load control instruction, and aircraft data analysis. Services include consulting, AHM messaging requirements, manual balance chart design, re-weighs, and training to provide customers with higher safety, return on investment, and environmental quality.
The document discusses various components of aviation and airport infrastructure management. It covers topics like air traffic management, runway infrastructure, fuel infrastructure, terminal infrastructure, and safety risk management. For runway infrastructure, it describes airport pavement management systems which are used to predict pavement condition and determine maintenance and repair plans. It also provides examples of managing risks from equipment outages at major US airports. For terminal infrastructure, it outlines the key functions of terminals and formulas for calculating passenger loads at security checkpoints.
This document discusses how the aircraft cost index (CI), which represents the cost of fuel per flight minute saved, can impact carbon emissions from air travel. The author analyzes how future changes in technology, policy, and the environment may affect CI values and emissions in 2030. Key findings include: 1) Average 1% savings in CO2 emissions for changes in CI value; 2) Up to -42% reduction in emissions expected from improvements in aircraft technology; and 3) Both increases and decreases in emissions predicted depending on specific policy changes and environmental factors considered. The conclusion emphasizes using CI as a tool to predict emission impacts and the need for further research, optimized policy implementation, and stakeholder collaboration to mitigate climate change.
The document provides an overview of various aircraft navigation systems throughout history, from early tools like stars, wind patterns and timekeeping to modern satellite-based systems. It discusses early radio navigation systems, celestial navigation using tools like sextants, dead reckoning through computations of speed and direction, map-matching systems, and global satellite systems like GPS. Modern area navigation systems are described as allowing aircraft flexible routing rather than direct routes between beacons, providing potential time, fuel and congestion benefits.
1) The document describes the design of an aircraft using Cradle to Cradle principles, with the goal of making it at least 90% recyclable.
2) Key aspects of the design include using ethanol as a biofuel, an aluminum structure and thermoplastic composites for secondary structures, and a disassembly process that allows for almost full recycling.
3) Analysis shows the Cradle to Cradle design meets performance requirements while having a lower operating cost than comparable aircraft, demonstrating the viability of applying these principles in aircraft design.
This document provides definitions and terms related to weight and balance control for aircraft. It defines key terms like center of gravity, datum, maximum weights, moments, and payload. It also explains the importance of balance and how adverse balance can impact an aircraft's stability and control. Maintaining proper weight and balance is important for the safety and performance of aircraft operations.
The document discusses technologies that the FAA is implementing to improve air traffic control systems and safety. It describes the current air traffic control system and issues like increasing traffic. It then outlines the National Airspace System Plan from 1981 to modernize equipment through projects like new computer systems at ARTCC facilities. Finally, it discusses several new technologies being developed or implemented, such as terminal Doppler weather radar, GPS navigation, data link communications, and multi-mode receivers, to further improve safety, efficiency, and capacity of the national air traffic system.
Optimizing precision final approach through gbasIrfan iftekhar
Ground-based augmentation systems (GBAS) provide localized precision GPS corrections to aircraft, enabling precision approaches. GBAS has benefits over instrument landing systems like supporting more runways with one system. GBAS also allows for flexible siting, steadier guidance, and less frequent inspections. While GBAS can increase efficiency and capacity, limitations remain such as the need for aircraft and ground infrastructure to support its full capabilities. Airports are working to certify GBAS for low-visibility operations and eventually replace ILS.
This document discusses advancing low visibility technologies through industry and government collaboration. It describes ongoing efforts by the FAA to implement new capabilities for low visibility flight operations using technologies like enhanced flight vision systems (EFVS). It proposes evaluating EFVS performance at the Volpe Center's outdoor weather test facility using collaborative agreements with EFVS manufacturers. The facility could assess EFVS visibility capabilities under different weather conditions and help standardize performance metrics.
The document discusses challenges facing the US air transportation system, including high airport operations volumes, complex environments, and minimal safety margins. It outlines various engineering and technical solutions to improve safety and address runway incursions, including improved airfield design and markings, runway status lights, enhanced taxiway centerlines, and arrestor beds. Recurrent training is required for pilots and vehicle drivers to address deviant behaviors. The goal is to reduce runway incursions by 10% by 2013 through a multidisciplinary approach committed to improving safety while increasing capacity.
EFVS technology allows pilots to see using infrared in low visibility conditions. While visibility is a key reason for EFVS, the main economic benefit is the ability to maintain schedules even in poor weather. This saves airlines and operators billions annually from delays and cancellations. New rules will allow operators with EFVS to depart as scheduled in low visibility instead of holding, saving time and fuel costs. EFVS also enables more efficient approaches, supporting sustainability goals while optimizing operations and schedules. The economic value of EFVS in saving time and costs outweighs the initial investment.
1. The document lists Key Performance Parameters (KPPs) and additional system requirements for an Advanced Pilot Training (APT) system. The KPPs include thresholds and objectives for aircraft and simulator availability, sustained G-forces, and simulator visual acuity and performance fidelity.
2. Additional requirements address maneuverability, weapons employment simulation, data links, angle of attack, turn rates, debriefing capabilities, and open systems architecture. Space, weight, power, and cooling growth provisions must also be included.
3. Scenario input is required for both aircraft and simulators to support tactical training, and the aircraft design should enable future in-flight refueling capability.
The document discusses the factors that influence airport runway configuration and layout. The four basic runway configurations are single runway, parallel runways, open-V runways, and intersecting runways. Runway layout is determined by operational capacity needs, environmental concerns, terrain, weather patterns, and the types of aircraft using the airport.
The document discusses the design of modern airports, using Rajiv Gandhi International Airport (RGIA) in Hyderabad, India as a case study. RGIA was built as a public-private partnership between 2004-2008 to replace Begumpet Airport. It has one passenger terminal built on 5,400 acres that can currently handle 12 million passengers annually, with plans to expand capacity to 40 million. Key components discussed include the single runway, taxiways, parking areas, and precision lighting to aid pilots on approach. The terminal building incorporates green building practices and was completed in a record 28 months.
This document provides details of an aircraft design project for a new personal jet called "The Flash" being designed by Kent Aerospace. It includes sections on requirements analysis, technical design, manufacturing plan, regulatory compliance, program management, finance, marketing, and socioeconomic impacts. The technical design section provides details on sizing methodology, assumptions, wing and tail geometry, thrust-to-weight ratio, powerplant specifications, wing loading data, and performance results. The design utilizes twin DGEN 380 turbofan engines from Price Induction and is intended to carry 3 passengers up to 800 nautical miles at a cruise speed of 230 knots.
Conceptual Design of a Light Sport AircraftDustan Gregory
The document provides a conceptual design for a light sport aircraft. It defines key parameters for light sport aircraft and summarizes the design of several existing models. The design process described initializes parameters like wing area and airfoil selection. Equations are presented to calculate performance metrics like drag, power required, climb rate, endurance and range. Requirements for the conceptual design are specified, including taking off, cruising, and landing with sufficient fuel reserves.
This document is a project report submitted by S Niranjan Varma for a Bachelor of Technology degree in Civil Engineering. It discusses airport planning and design. The report includes an introduction to airport surveys conducted for planning, such as topographical, drainage, soil and meteorological surveys. It also covers runway orientation factors like wind conditions. The project involves designing the airside area including the runway, taxiway and apron. It includes designing the terminal building using software and calculating loads and structural elements. The landside area plan and calculations are also presented. The conclusion summarizes the project and references are provided.
This presentation briefly explains about important factors affecting the design and plan of Airports.
Topics Covered: Introduction, AAI, Features of planes affecting the design of airports, size of airport, site selection for airport, visual aids, difficulries in planning an airport.
This thesis analyzes the aerodynamic performance of a canard-configured forward swept wing aircraft design. Canards are small wings mounted in front of the main wing that act as horizontal stabilizers to control pitch. A forward swept wing directs airflow inward from the wingtips toward the root. The study selects airfoils for the canards, wing root, and wing tip based on criteria to induce earlier stalling at the root than the tips. Graphs of lift, drag, and moment coefficients versus angle of attack are presented for the reference design and two experimental airfoil sets. The second set is chosen for its larger gaps in stalling angles and higher maneuverability potential. In conclusion, a canard-configured forward
The document analyzes the stability and control of the Zivko Edge 540T aerobatic aircraft. It estimates key physical properties and determines equilibrium flight conditions. Non-dimensional stability derivatives are then calculated, showing the aircraft is longitudinally stable. Lateral stability is also analyzed, with the aircraft found to be laterally stable except for an unstable spiral mode. Dimensional derivatives are used to examine specific stability modes, with most modes stable except the spiral mode.
EGS Weight & Balance Services provides aircraft load control and performance engineering services. Led by Managing Director Eric Bahn, EGS has over 20 years of experience in operations management, load control instruction, and aircraft data analysis. Services include consulting, AHM messaging requirements, manual balance chart design, re-weighs, and training to provide customers with higher safety, return on investment, and environmental quality.
The document discusses various components of aviation and airport infrastructure management. It covers topics like air traffic management, runway infrastructure, fuel infrastructure, terminal infrastructure, and safety risk management. For runway infrastructure, it describes airport pavement management systems which are used to predict pavement condition and determine maintenance and repair plans. It also provides examples of managing risks from equipment outages at major US airports. For terminal infrastructure, it outlines the key functions of terminals and formulas for calculating passenger loads at security checkpoints.
This document discusses how the aircraft cost index (CI), which represents the cost of fuel per flight minute saved, can impact carbon emissions from air travel. The author analyzes how future changes in technology, policy, and the environment may affect CI values and emissions in 2030. Key findings include: 1) Average 1% savings in CO2 emissions for changes in CI value; 2) Up to -42% reduction in emissions expected from improvements in aircraft technology; and 3) Both increases and decreases in emissions predicted depending on specific policy changes and environmental factors considered. The conclusion emphasizes using CI as a tool to predict emission impacts and the need for further research, optimized policy implementation, and stakeholder collaboration to mitigate climate change.
The document provides an overview of various aircraft navigation systems throughout history, from early tools like stars, wind patterns and timekeeping to modern satellite-based systems. It discusses early radio navigation systems, celestial navigation using tools like sextants, dead reckoning through computations of speed and direction, map-matching systems, and global satellite systems like GPS. Modern area navigation systems are described as allowing aircraft flexible routing rather than direct routes between beacons, providing potential time, fuel and congestion benefits.
1) The document describes the design of an aircraft using Cradle to Cradle principles, with the goal of making it at least 90% recyclable.
2) Key aspects of the design include using ethanol as a biofuel, an aluminum structure and thermoplastic composites for secondary structures, and a disassembly process that allows for almost full recycling.
3) Analysis shows the Cradle to Cradle design meets performance requirements while having a lower operating cost than comparable aircraft, demonstrating the viability of applying these principles in aircraft design.
This document provides definitions and terms related to weight and balance control for aircraft. It defines key terms like center of gravity, datum, maximum weights, moments, and payload. It also explains the importance of balance and how adverse balance can impact an aircraft's stability and control. Maintaining proper weight and balance is important for the safety and performance of aircraft operations.
The document discusses technologies that the FAA is implementing to improve air traffic control systems and safety. It describes the current air traffic control system and issues like increasing traffic. It then outlines the National Airspace System Plan from 1981 to modernize equipment through projects like new computer systems at ARTCC facilities. Finally, it discusses several new technologies being developed or implemented, such as terminal Doppler weather radar, GPS navigation, data link communications, and multi-mode receivers, to further improve safety, efficiency, and capacity of the national air traffic system.
Optimizing precision final approach through gbasIrfan iftekhar
Ground-based augmentation systems (GBAS) provide localized precision GPS corrections to aircraft, enabling precision approaches. GBAS has benefits over instrument landing systems like supporting more runways with one system. GBAS also allows for flexible siting, steadier guidance, and less frequent inspections. While GBAS can increase efficiency and capacity, limitations remain such as the need for aircraft and ground infrastructure to support its full capabilities. Airports are working to certify GBAS for low-visibility operations and eventually replace ILS.
This document discusses advancing low visibility technologies through industry and government collaboration. It describes ongoing efforts by the FAA to implement new capabilities for low visibility flight operations using technologies like enhanced flight vision systems (EFVS). It proposes evaluating EFVS performance at the Volpe Center's outdoor weather test facility using collaborative agreements with EFVS manufacturers. The facility could assess EFVS visibility capabilities under different weather conditions and help standardize performance metrics.
The document discusses challenges facing the US air transportation system, including high airport operations volumes, complex environments, and minimal safety margins. It outlines various engineering and technical solutions to improve safety and address runway incursions, including improved airfield design and markings, runway status lights, enhanced taxiway centerlines, and arrestor beds. Recurrent training is required for pilots and vehicle drivers to address deviant behaviors. The goal is to reduce runway incursions by 10% by 2013 through a multidisciplinary approach committed to improving safety while increasing capacity.
EFVS technology allows pilots to see using infrared in low visibility conditions. While visibility is a key reason for EFVS, the main economic benefit is the ability to maintain schedules even in poor weather. This saves airlines and operators billions annually from delays and cancellations. New rules will allow operators with EFVS to depart as scheduled in low visibility instead of holding, saving time and fuel costs. EFVS also enables more efficient approaches, supporting sustainability goals while optimizing operations and schedules. The economic value of EFVS in saving time and costs outweighs the initial investment.
The Future Air Navigation System (FANS) allows for digital communication between pilots and air traffic controllers, improving upon traditional analog radio systems. It integrates satellite-based navigation and automatic dependent surveillance to enable more efficient routing and reduced separation standards in oceanic and remote airspace. FANS was developed in the 1980s and 1990s by ICAO, airlines, and aircraft manufacturers like Boeing and Airbus to enhance safety and increase airspace capacity through enhanced aircraft communications, navigation, and surveillance capabilities.
This paper proposes a method to calculate a flight cost of an unmanned aerial vehicle (UAV) considering its change of heading angle though there are many reasons that cause the energy consumption. The proposed approach demonstrates that when a UAV moves from a starting position/point to a target/goal position/point, if the number of obstacle increases, the number of heading change would also increase. As a result, it raises the energy consumption of the UAV. It also shows that the magnitude of heading change would affect the energy consumption proportionally. The theoretical analysis as well as the simulation outcome proves the usefulness of the proposed technique.
The document discusses the Next Generation Air Transportation System (NextGen) program in the United States and the Single European Sky ATM Research (SESAR) program in Europe. Both programs aim to fundamentally transform air traffic management systems to increase capacity and efficiency as air traffic volumes grow. NextGen and SESAR involve introducing new technologies like GPS and automated dependent surveillance to improve precision, reduce uncertainties, and allow for more direct flight paths. However, both programs also face significant challenges in implementing complex new technologies, coordinating interdependent systems, and managing high costs.
To help ensure safe flights, air traffic controllers enforce a minim.pdfarihantpuneteleshope
To help ensure safe flights, air traffic controllers enforce a minimum time interval between
takeoffs. Explain why this time interval between takeoffs can be shortened if the wind has a
cross-runway component ( as opposed to blowing directly down the runway)?
Solution
Answer :
Use different types of air traffic pattern.
Procedures in the pattern[edit]
Aircraft are expected to join and leave the pattern, following the pattern already in use.
Sometimes this will be at the discretion of the pilot, while at other times the pilot will be directed
by air traffic control.
There are conventions for joining the pattern, used in different jurisdictions.
Similarly, there are conventions for departing the pattern.
There is also a procedure known as an \"orbit\", where an aircraft flies a 360° loop either
clockwise or anticlockwise. This is usually to allow greater separation with other traffic ahead in
the pattern. This can be the result of a controller\'s instruction. If at the pilot\'s initiative, the pilot
will report e.g. \"(tail number or flight number) making one left-hand orbit, will advise
complete\".
To practice take off and landing, a pilot would often fly many patterns, one after another, from
the same runway. Upon each landing, depending on the runway distance remaining, aircraft and
pilot capabilities, noise abatement procedures in effect, and air traffic control clearance, the pilot
will perform either a full stop landing (taxi to the runway beginning for subsequent take-off), a
touch-and-go (stabilize in the landing roll, reconfigure the aircraft for take-off, and take-off
without ever stopping the aircraft), or a stop-and-go (decelerate to a stop, then take-off from the
remaining runway). In the U.S., when operating in a controlled airport a pilot can be cleared for
the option, allowing any of the landing options above, or a rejected landing, at pilot\'s discretion.
Time interval importance in radar system.
Radar coverage
Since centers control a large airspace area, they will typically use long range radar that has the
capability, at higher altitudes, to see aircraft within 200 nautical miles (370 km) of the radar
antenna. They may also use TRACON radar data to control when it provides a better \"picture\"
of the traffic or when it can fill in a portion of the area not covered by the long range radar.
In the U.S. system, at higher altitudes, over 90% of the U.S. airspace is covered by radar and
often by multiple radar systems; however, coverage may be inconsistent at lower altitudes used
by unpressurized aircraft due to high terrain or distance from radar facilities. A center may
require numerous radar systems to cover the airspace assigned to them, and may also rely on
pilot position reports from aircraft flying below the floor of radar coverage. This results in a
large amount of data being available to the controller. To address this, automation systems have
been designed that consolidate the radar data for the controller. This consolid.
This paper addresses an optimization of Unmanned Aerial Vehicle (UAV) flight trajectories
by bank-turn mechanism for a fixed-wing UAV at a constant altitude.
FANS (Future Air Navigation System) uses satellite technology and data links to allow for more efficient air traffic management. It allows for reduced separation between planes, more direct routing, and two-way digital communication between air traffic control and pilots. FANS includes installations like ADS-B for surveillance, GPS, and CPDLC for text-based clearance and guidance communication to replace some voice radio. Its implementation aims to reduce fuel costs and increase airspace capacity over traditional radar-based systems.
Melbourne East West Corridor Trajectory DescentPerth Now
This paper discourses the descent trajectory in the Melbourne East West Corridor, in the aspect of fuel efficiency for carbon savings. Three top of descent approaches put down the foundation for the research: The Reduced Vertical Separation Minimum, Free Route Experimental Encounter Resolution, and the Continuous Descent Approach that is practiced within the Melbourne airspace.
Using a theoretical construct of fuel fraction during loiter, outline of approach and landing the derivative of fuel burn and correlated emissions can be defined. A single aircraft type of the Australian flag bearer, Quantas Airways Limited is to be selected, in a sample size to be determined on the volume of available information.
On the overall, this research is typical a case study in a framework of comparative analysis using a single equation.
At the given congestion of Melbourne Airport year-on-year 200,000 aircraft movements for 29 million passengers; the outcome of this research is expected to show positive results in fuel efficiency for carbon savings. Ease of approach and reduced time to land are thought to be the substantive variables due the Melbourne East West Corridor.
Boeing has developed a vertical situation display (VSD) to help prevent accidents related to controlled flight into terrain and approach/landing. The VSD provides pilots with an intuitive graphical representation of the aircraft's vertical flight path relative to terrain and the desired descent path. It is designed to both enhance safety and reduce operating costs by decreasing incidents like missed approaches or hard landings. The VSD will be available as an option on new Boeing 737s starting in early 2003 and can also be retrofitted onto existing 737s.
This document presents a hybrid approach combining column generation, constraint programming, and local search to solve the Tail Assignment problem in airline planning. The Tail Assignment problem involves assigning specific flight sequences and maintenance activities to individual aircraft while satisfying operational constraints. The hybrid approach can find feasible solutions quickly for operations management and near-optimal solutions for long-term planning. Computational results show the practical effectiveness of the approach.
Delays in air traffic management a surrogate perspectivePaula R MARK
The idea of waiting is usually associated with mixed emotions of trepidation and anger. But delays in the air transport sector may be good from an economic perspective. This presentation uses a statistical analysis of aviation data to show a surrogate perspective of delays.
This document provides information on geometric design considerations for airport runways, taxiways, and terminals. It discusses factors that influence runway orientation such as wind conditions and aircraft performance. It also describes guidelines for determining basic runway length based on elevation, temperature, and aircraft characteristics. Additional topics covered include runway configuration, geometry standards for length, width, gradients and sight distances, taxiway design standards, and concepts for terminal area layout and space requirements.
FRTO allows for more flexible routing and improved efficiency of flights. It utilizes modern aircraft navigation capabilities and air traffic management technologies to dynamically adjust routes based on traffic patterns, reducing congestion and flight lengths. This flexibility improves key performance areas like access, capacity, efficiency and the environment. Studies show potential cost savings from reduced fuel burn and flight times of implementing flexible and optimized routing.
An Analysis of Runway Capacity at International Airport Sultan Aji Sulaiman B...irjes
This document analyzes the runway capacity at Sultan Aji Sulaiman International Airport in Balikpapan, Indonesia. The airport has experienced 12.2% annual growth in aircraft movements over the last 5 years. However, the single runway and five exit taxiways limit its capacity. To increase capacity, the study examines runway occupancy times for landing and takeoff and different exit taxiway configurations. Reconstructing one exit taxiway into a rapid exit taxiway could increase the runway's capacity from 21 to 28 aircraft movements per hour. Literature on runway and taxiway design is also reviewed to understand factors that influence capacity such as taxiway layout, location and type.
Air Traffic Control Database Management System for Seamless TransitIRJET Journal
This document proposes an air traffic control database management system to improve efficiency. It first discusses the current air traffic control system and some shortcomings, such as delays caused by aircraft malfunctions. It then reviews several other papers on air traffic control systems and management. Finally, it proposes a database management system using MySQL and Xampp to store air traffic control data in order to help controllers manage flights more seamlessly and minimize delays. The system would track information like flight plans, aircraft locations, runways in use, and gates being used to help controllers route flights efficiently.
CONCEPT OF OPERATIONS: THE TRANSITION FROM CREWED TO UNCREWED UAMiQHub
The document outlines a concept of operations for uncrewed urban air mobility (UAM). It describes key stakeholders in UAM including the flying public, regulatory agencies, and UAM industry players. The concept involves enabling infrastructure like vertiports and airspace, as well as UAM aircraft and command and control links. A steppingstone approach is proposed that evolves from current piloted UAM to eventually fully autonomous multi-vehicle operations managed remotely. Key roles and responsibilities are defined for entities involved in UAM operations. The passenger journey and nominal flight operations are illustrated from pre-flight planning through post-flight activities.
This document provides an overview of avionics systems. It defines avionics as electronics used in aircraft and describes some key avionics subsystems including displays, communications, flight controls, sensors, navigation, and task automation. Modern avionics play an essential role in aircraft functionality and safety by enabling minimum crew operations and automated flight. Avionics can account for a significant portion of an aircraft's total costs.
Similar to Enhancing Pilot Ability to Perform CDA with Descriptive Waypoints (20)
Connect Conference 2022: Passive House - Economic and Environmental Solution...TE Studio
Passive House: The Economic and Environmental Solution for Sustainable Real Estate. Lecture by Tim Eian of TE Studio Passive House Design in November 2022 in Minneapolis.
- The Built Environment
- Let's imagine the perfect building
- The Passive House standard
- Why Passive House targets
- Clean Energy Plans?!
- How does Passive House compare and fit in?
- The business case for Passive House real estate
- Tools to quantify the value of Passive House
- What can I do?
- Resources
International Upcycling Research Network advisory board meeting 4Kyungeun Sung
Slides used for the International Upcycling Research Network advisory board 4 (last one). The project is based at De Montfort University in Leicester, UK, and funded by the Arts and Humanities Research Council.
Explore the essential graphic design tools and software that can elevate your creative projects. Discover industry favorites and innovative solutions for stunning design results.
Fonts play a crucial role in both User Interface (UI) and User Experience (UX) design. They affect readability, accessibility, aesthetics, and overall user perception.
Practical eLearning Makeovers for EveryoneBianca Woods
Welcome to Practical eLearning Makeovers for Everyone. In this presentation, we’ll take a look at a bunch of easy-to-use visual design tips and tricks. And we’ll do this by using them to spruce up some eLearning screens that are in dire need of a new look.
PDF SubmissionDigital Marketing Institute in NoidaPoojaSaini954651
https://www.safalta.com/online-digital-marketing/advance-digital-marketing-training-in-noidaTop Digital Marketing Institute in Noida: Boost Your Career Fast
[3:29 am, 30/05/2024] +91 83818 43552: Safalta Digital Marketing Institute in Noida also provides advanced classes for individuals seeking to develop their expertise and skills in this field. These classes, led by industry experts with vast experience, focus on specific aspects of digital marketing such as advanced SEO strategies, sophisticated content creation techniques, and data-driven analytics.
Technoblade The Legacy of a Minecraft Legend.Techno Merch
Technoblade, born Alex on June 1, 1999, was a legendary Minecraft YouTuber known for his sharp wit and exceptional PvP skills. Starting his channel in 2013, he gained nearly 11 million subscribers. His private battle with metastatic sarcoma ended in June 2022, but his enduring legacy continues to inspire millions.
ARENA - Young adults in the workplace (Knight Moves).pdfKnight Moves
Presentations of Bavo Raeymaekers (Project lead youth unemployment at the City of Antwerp), Suzan Martens (Service designer at Knight Moves) and Adriaan De Keersmaeker (Community manager at Talk to C)
during the 'Arena • Young adults in the workplace' conference hosted by Knight Moves.
Enhancing Pilot Ability to Perform CDA with Descriptive Waypoints
1. 1
ENHANCING PILOT ABILITY TO PERFORM CDA
WITH DESCRIPTIVE WAYPOINTS
Michael LaMarr & Dr. Nhut Ho, California State University Northridge, California
Dr. Walter Johnson & Vernol Battiste, NASA Ames, Moffett Field, California
Joe Biviano, Lockheed Martin, Palmdale, California
Abstract
Aircraft noise is a burden on people living
around airports and is an impediment to the growth of
air transportation. Continuous Descent Approach
(CDA) is an approach that reduces noise impact on
the ground by keeping the aircraft at a higher altitude
longer than standard approaches and by keeping
engines idle or near idle. However, CDA
implementation requires controllers to add large
separation buffers between aircraft because aircraft of
different sizes and weights descend at different rates,
consequently creating uncertainty in separation
between aircraft. This paper proposes a viable near-
term solution to allow pilots perform CDA more
consistently through the use of Descriptive
Waypoints (DWs), or checkpoints in terms of
altitudes and speeds along the CDA path that provide
the pilot targets and feedback along the CDA path. A
human in the loop study was conducted to develop
and determine the effectiveness of using DWs to
improve flight performance during CDA procedures,
and provide recommendations on DW design and
integration into existing CDA procedures.
Twelve instrument rated commercial pilots flew
three different wind conditions using one, three, or
five DWs. Dependent variables included: deviation
from DW target altitude and Indicated Airspeed
(IAS), average power usage, perceived workload, and
pilot acceptance of DWs. Objective and subjective
data were also collected to obtain pilot feedback on
the design of DWs and their integration into CDA
procedures, and determine pilot strategies while
flying CDA with DWs.
The results showed that as the number of DW
increases, mean altitude deviations from the DW
targets decreased from 922 feet to 196 feet and
standard deviations from 571 feet to 239 feet with a
slight increase in perceived workload and one percent
increase in power usage and. The pilots commented
that the DWs provide useful feedback to strategize
how to make corrections to the altitude deviation in
the vertical path, and that they would feel
comfortable having the DW integrated in the flight
chart or shown as a vertical view on a display. The
pilots also provided a number of recommendations
for integrating the DW into Jeppesen charts and roles
for the pilot flying and the pilot not flying.
These results imply that DWs can be used as an
effective cuing system to enhance pilot ability to
perform CDA, and that they are a potential choice for
near to midterm implementation in improving the
effectiveness of CDA procedures.
Background
Continuous Descent Approach Benefits
Noise and emissions produced by aircraft when
landing are a burden on people living around airports
and is an impediment to the growth of air
transportation. The produced noise limits how many
aircraft can land at night and the ability to expand
more runways or build new airports in populated
areas. Currently, aircraft descend and land at
different speeds based on their size and weight,
making it difficult to predict their future trajectory.
Air Traffic Controllers (ATC) compensate for
dissimilar aircraft performance by creating an
approach pattern in which all aircraft fly time-
consuming and fuel-burning stair-step flight
segments at the same speeds as they enter the
terminal area [1,2,3]. This practice makes it
manageable for the ATC to separate aircraft;
however, it creates a significant noise impact on the
local community. The noise is most profound in
areas where the aircraft have to fly at low altitudes
2. 2
near the runway because of the existing navigation
constraints. Specifically, aircraft land by using an
instrument landing system (ILS) glide slope to
intercept the glide path at the correct descent angle to
the runway (see figure 1). The ILS provides the pilot
with lateral and vertical guidance to maintain the
correct approach orientation for landing. This is
accomplished by leveling off at an altitude that
allows the aircraft to intercept the glide slope from
below. If the aircraft flies above the glide slope it
may intercept a false glide slope and come into the
Figure 1: Conventional Approach and Continuous Descent Approach
airport at an incorrect landing angle. To operate
within the navigation constraints of the ILS and
reduce noise impact, noise abatement approach
procedures have been developed and implemented.
One such procedure is Continuous Descent Approach
(CDA). CDA also offers other benefits such as fuel
savings and lower emissions impact by using an idle
or near idle power and by decelerating the aircraft at
a higher altitude longer than the standard landing
procedure without reverting to level flights (See
Figure 1). The benefits of CDA have shown in many
studies and demonstrations, such as the CDA flight
demonstration study conducted in Louisville,
Kentucky with UPS Boeing 767-300 aircraft
equipped with the Pegasus flight management system
(FMS) [4]. It was shown that CDA can reduce noise
by 3.5 to 6.5 dBA (3 dBA is noticeable to the ear)
and fuel consumption by 400 to 500 pounds.
CDA Implementation Challenges & Current
Work on Improving Performance Predictability
Currently implementation of CDA is not
practical in moderate to high traffic because it
requires a larger separation buffer between aircraft
than the standard landing procedure. Predicting
where the aircraft will be is cognitively taxing on the
controller and pilots because deceleration is non-
linear and humans have a difficult time judging non-
linear deceleration when speeds are constantly
changing [3, 5]. To implement CDA, ATC have to
know when aircraft are at the right distance from the
airport to initiate the clearance to start the descent. If
the air traffic controller tells the pilot to initiate CDA
too early, then the aircraft will arrive before the
runway and will have to level out before landing.
Leveling out early requires power increase, which in
turn creates more noise and defeats the purpose of the
procedure. If the ATC tells the pilot to initiate the
procedure too late, then the pilot will end up making
a fast landing or have to initiate a go-around for
another approach (which produces more noise and
uses more fuel, which also defeats the purpose of the
CDA).
To assist ATC in managing CDA, ground based
automation is being developed. Stell et al is working
on an algorithm for ground based automation called
Three-Dimensional Path Arrival Management
(3DPAM) to provide top of descent (TOD)
prediction to controllers [6]. The purpose of this
algorithm is to predict TOD location within a
tolerance of 5 nm to help controllers manage CDA
traffic. This algorithm takes into account that even
with a perfect TOD predictor the vertical profiles and
path distance must be predicted accurately as well.
Kuper et al conducted a study with three
different ground based support tools for ATC to work
Airport
Continuous
Descent Approach
Conventional
Approach
10,000
feet
4,000 feet
ILS Glide Slope
3. 3
in Super Density Operations (SDO) environment [7].
These tools are timeline, slot marker, and speed
advisory. Timeline gives the ATC estimated time of
arrival (ETA), slot marker gives a visual
representation (circle) to the ATC where the aircraft
should be if on schedule, and the speed advisory
provides controllers with air speed advisories that can
be used to correct scheduling errors. Based on
subjective feedback, ATC preferred the slot marker
tool.
Alam proposed that dynamic CDA would allow
the FMS to create unique CDA routes based on
aircraft type, size, and weight [8]. But in order for
dynamic CDA to be implemented ATC will need to
have the same information as the pilot. This can be
accomplished with real time data linking between
controllers and pilots with controller pilot data link
communications (CPDLC). The controller would be
able to uplink the flight plan to the FMS to initiate
CDA, and the pilot would then send the executed
FMS CDA route back to the controller.
Ren and Clarke developed the Tool for the
Analysis of Separation and Throughput (TASAT) to
predict trajectories of different aircraft performing
CDA and to determine the minimum spacing at a
metering point in order to avoid separation violations
[9]. Factors that contribute to aircraft trajectory
variations are aircraft type and weight, FMS logic,
and pilot technique and winds.
Other challenges to the implementation of CDA
procedures remain the difficulty that pilots have in
managing the deceleration of aircraft in the presence
of uncertainties in pilot response time, vertical
navigation performance (VNAV - controls vertical
automation of aircraft according to flight profile
programmed in the FMS), and wind conditions [10].
Koeslag also identified other issues with current
CDAs [11]. One issue is how the vertical flight
profile is managed and depends on the type of FMS
installed. Another issue is that wind can cause the
aircraft to deviate from the FMS-predicted flight
trajectory. One of Koeslag’s proposed solutions was
to have a fixed CDA vertical profile to improve
arrival time predictability and add flap guidance in
the primary flight display (PFD) to correct for speed
deviations (see Figure 2).
Figure 2: Flap Cues Recommended by Koeslag in
Primary Flight Display [11]
Other research efforts aiming to make CDA
more predictable are focusing on equipping FMS
with 4D guidance (x, y, z, and time). Moore
proposed 4D information with a required time of
arrival (RTA) to aid ATC in establishing a strategic
time scale of CDA traffic flow [12]. The algorithms
designed in this research are aimed to minimize time,
fuel, and emissions produced. One problem noted is
that automation can cause the VNAV to make
occasional thrust changes that can generate extra
noise and fuel usage.
Other research on RTA during CDA operation
proposed to provide pilots with an energy
management system (see Figure 3) in the navigation
display to minimize fuel, noise, and emissions. The
system provides pilots an optimal vertical path with
energy events and energy error cues for managing
throttle and drag [13].
Figure 3: Energy Management System used by
NASA Langley Research Center
4. 4
Other flight demonstration studies found that
pilot delay in initiating the flaps had undesired effects
on VNAV in that it causes the aircraft to deviate from
the altitude programed on the FMS [4]. Another
problem identified with the VNAV is that when
descending, the VNAV’s logic gives the altitude
constraint higher priority than the speed constraint.
With factors such as tail wind, the aircraft does not
always meet the speed targets. It is important to meet
both the speed and altitude constraints on the flight
path for fuel and time efficiency, and for traffic
separation.
Development of Descriptive Waypoint
These studies have been beneficial to CDA
research and development, but are aiming for mid to
long term implementation; until better VNAV logics
and FMS designs can compensate for pilot delay,
altitude and speed constraints, and wind
uncertainties, the pilot has to control the vertical
profile manually. If pilots have information to help
them stay on the flight path and manage their
aircraft’s speed, CDA would be more feasible for
daily use. One way to aid pilots in executing CDA is
to give them feedback information. Without the help
of a cuing system, pilots find it difficult to manage
the aircraft energy to meet a target speed at a specific
altitude in the presence of uncertainty. According to
Ho et al, there are two reasons for uncertainty during
CDA [3]. One reason is the pilot’s inability to
estimate future position of aircraft because the
deceleration profile is non-linear. The second reason
is that the pilot’s projection may be incorrect because
of wind uncertainty. They proposed to provide pilot
feedback info in terms of gates, which are an altitude
and speed target along the flight path. For
consistency purpose, gates will be called Descriptive
Waypoints (DW) in this paper. In Ho’s study,
different numbers of gate conditions (0, 1, 2, and 3)
were proposed to use with a flap schedule. Each of
these conditions also had wind uncertainty and no
wind uncertainty. For the two DW condition, the
DWs were located at 5000 and 3000 feet from the
runway, and the three DW condition had DWs at
5000, 4140, and 3000 feet (see Figure 4). The DWs
were given to pilots on a cue card shown in Figure 4.
Providing vertical information and DW at 7,000 feet
altitude improved pilot ability to perform CDA. In
the three DW condition, pilots were able to achieve
the target speed at a higher rate than the other
conditions.
Figure 4: DW Cues with Flap, Altitude and
Indicated Air Speed References [3]
Given that CDA is being considered to be
initiated at further distances from the airport (e.g.,
such as 37,000 to 40,000) for fuel savings and
emissions reduction, the concept of DW was
conceived and formulated as an extension of the gate
concept [14]. The name DW was chosen because
dynamic waypoints (target altitude and speed
waypoints that can be created in real time, relying on
the existing waypoint database) focus on providing
updated waypoint information, and DW is a
description of a waypoint that could include a time
target, flap requirement, gear deployment, target
altitude, and speed. For this study, only altitude and
Indicated Air Speed (IAS) was provided in the DW.
Flap information was displayed in the PFD.
Display of Descriptive Waypoints
With the description of DW defined, it is
important to examine how to display the DW
information to the pilot. The navigation display (see
Figure 5) is a useful way of informing the pilot of the
general surroundings, and is currently limited to a 2D
perspective.
5. 5
Figure 5: 2D Navigation Display
Pilots also use arrival charts when they are on
their final approach, with the vertical information
(altitude) displayed as text as in the 2D navigation
display, as well. Figure 6 represents the vertical
profile the pilot needs to fly with the step down fixes
to intercept the glide slope and land.
Figure 6: Flight Chart Final Approach [15]
Thomas and Wickens found that it is easier to
make specific and accurate judgments based on
absolute spatial information displayed in 2D with 3D
information [16]. This is because 3D displays tend to
make the x, y, and z axis ambiguous, whereas 2D
information gives precise x and y information, but
will need the 3D information in text. There is also a
problem that occurs while using 3D views: without
other depth cues available, the location of objects
become ambiguous [17]. Even with this problem 3D
views do have their advantages. For example, shape
understanding is beneficial in 3D, whereas 2D is
more accurate for precision tasks [18]. For the
current study with a focus on implementation in the
near term, it makes sense to display the DWs to pilots
in 2D because pilots are only controlling their
vertical descent during CDA.
Implementation of DWs into the current flight
deck system can be accomplished by displaying them
in a vertical flight chart (see Figure 7). Vertical flight
charts typically display the final approach right
before the glide slope at approximately 3,000 to
10,000 feet altitude. The initial altitude in the
current study starts at 23,000 feet altitude at 70 miles
from the airport. This is motivated by the fact that
CDA procedures are being proposed to start at a very
far distance from the airport, such as the top of
descent location, which is typically at 37,000 to
40,000ft [14].
6. 6
Figure 7: Three Descriptive Waypoints
A possible solution for midterm to long term
implementation is to use a coplanar view (horizontal
and vertical profiles) of the navigation with DW
information. The vertical display would benefit
pilots, enabling them to monitor the vertical profile
when VNAV is turned off and the pilot is manually
flying the vertical profile (see Figure 8).
Figure 8: Coplanar Navigation View [19]
Another possible long term solution that can
help the pilot perform CDA more efficiently is to
display DWs in the Cockpit Situation Display (CSD)
to provide 3D visualization of the flight plan (see
Figure 9) [20]. CSD is a navigation aid that pilots
can use to gain information of surrounding air traffic,
alert them of possible conflicts, provide spacing
tools, etc. CSD eliminates 3D ambiguities by
allowing the pilot to rotate the screen 360 degrees
and switch to 2D anytime.
Figure 9: 3D Cockpit Situation Display
The current study is an extension of Ho’s gate
study of adding predictability to the pilot during
CDA. VNAV was set to off because it was shown to
affect CDA performance in previous studies. LNAV
was left on auto-pilot
7. 7
Method
Design
A 3 wind (Fast, Normal, and Slow) x 3 DW
(One, Three, and Five) within-subject factorial design
was used. The wind conditions (Fast, Normal, and
Slow) were based on historical data at Louisville
International Airport and were chosen to produce
noticeable differences. In the Fast wind condition, the
wind speed started at 52.8 knots (60% higher than the
normal wind condition), the Normal wind condition
had a starting wind speed of 33 knots, and the Slow
wind condition had a starting speed of 19.8 knots
(40% lower than the normal wind condition) (see
Figure 10). The One-DW, Three-DW and Five-DW
conditions provided the pilots with one, three, and
five DWs respectively along the CDA path (see
Figures 12-14). The number of DWs was designed to
vary the amount of feedback provided to the pilots.
Dependent variables included: altitude and IAS
deviation, computed as the absolute deviation from
DW target altitude and IAS. Altitude deviations and
IAS deviations are metrics used to evaluate how
DWs assist pilots to maintain the CDA flight profile.
Power percentage usage was computed as the average
power the aircraft uses during the CDA. Perceived
workload, pilot acceptance of DW, pilot strategies
and other subjective data were collected in a
questionnaire (rating scales and open ended
questions) to evaluate the effectiveness of DW and
obtain feedback on pilot acceptance and the
integration of DW into existing CDA procedures.
Figure 10: Wind Speed
Material
Stimuli were displayed on two 19” monitors,
with one monitor running the Multi Aircraft Control
Station (MACS) software which provides a dynamic
interface that allows the pilot to fly and interact with
the aircraft’s systems, such as IAS, vertical speed,
flap settings, and altitude [21]. The other monitor
was running Cockpit Situation Display (CSD) which
was used to display the CDA flight plan on a 2D
fixed vertical view (see Figure 11) [20]. Depending
on the condition, the DWs were displayed on a flight
chart as one, three, and five DWs as shown in Figures
12-14. The CDA profile used in the current study
was developed and verified by NASA in a previous
study [20, 21]. Modifications were made to the CDA
profile by creating aircraft start and end points,
removing all traffic, and by adding DW locations
with considerations for the aircraft’s kinetic and
potential energy, noise, deceleration, speed/altitude
targets, and power usage. The CDA profile flew is
the same in all conditions.
Figure 11: MACS (top picture) and Cockpit
Situation Display (bottom picture)
0
10
20
30
40
50
60
0 20000
Altitude, [ft]
Fast
Wind
Normal
Wind
Slow
Wind
WindSpeed,[knots]
8. 8
Figure 12: One Descriptive Waypoint Condition
Figure 13: Three Descriptive Waypoints Condition
Figure 14: Five Descriptive Waypoints Condition
9. 9
Facilities
The study was conducted in the Systems
Engineering Research Laboratory at California State
University Northridge (see Figure 15). Pilots were in
a room with a one-way mirror and sat at a desk with
two computer monitors and a flight chart, and used a
mouse to interact with the monitors.
Figure 15: Pilot Station Setup
Participants
Participants included twelve instrument-rated,
commercial pilots (11 male, 1 female) between the
ages of 24 and 67 (Mean 37.64 years old) with years
of flying between 2 and 37 years (Mean 18.75 years)
and with 590 to 23,000 (Mean 7660) hours of flight
time. Two pilots have experience with CDA, and one
has experience with CDA simulation.
Results
Altitude and IAS deviations and average power
were collected from MACS output and put into excel
for each participant for nine conditions. Data was
organized by dependent variable, and a 3x3 (Wind x
DW) analysis of variance (ANOVA) was run on
SPSS version 17 for each of the dependent variables.
Attitude and IAS Deviation
Figure 16 shows the means and standard
deviations of altitude deviations at the DW targets 1
through 5. There was a significant main effect of
DW on altitude deviation on DW targets 2 through 4,
F(1.392, 15.308)= 26.364, p<0.000, etap
2
=1.000 and
no significant main effect of Wind on average
altitude deviation on DW targets 2 through 4. In the
Five-DW condition, (mean=196.06 sd=238.90)
significant differences in average altitude deviation
were found compared to the Three-DW condition
(mean=516.00 sd=287.68) and the One-DW
condition (mean=922.32 sd=570.61). The difference
in altitude deviation between the Five-DW and
Three- DW condition was 319.94 feet, between the
Three-DW and One-DW condition was 406.32 feet,
and between the Five-DW and One-DW condition
was 726.26 feet. There was no significant interaction
effect between DW and Wind on altitude deviation of
DW targets 2 through 4. There were no main
effects or interactions with IAS.
Figure 16: Average Altitude Deviation Main effect on DW
0
200
400
600
800
1000
1200
1400
1600
18nm to Cheri:
DW Target 1
Cheri:
DW Target 2
Alt<10:
DW Target 3
10nm to SDF:
DW Target 4
5nm to SDF:
DW Target 5
1 DW
Condition
3 DW
Condition
5 DW
Condition
AltitudeDeviation,[Ft]
10. 10
Power Usage
There was a significant main effect of DW on
average power percentage, F(1.928, 21.203) = 3.731,
p<0.042, η=0.609, and no significant main effect of
Wind on average power percentage. In the One-DW
condition, (mean=7.25 sd=2.31) significant
differences of average power percentage were found
compared to the Three-DW condition (mean=7.62
sd=2.39) and the Five- DW condition (mean=8.35
sd=3.45). The difference in average power
percentage between the One-DW and Three- DW
conditions was .37, between the Three-DW and Five-
DW conditions was .73 average power, and between
the Five-DW and One-DW conditions was 1.1.
There was no significant interaction effect between
DW and Wind on average power percentage. Figure
17 shows the mean power for different DW
conditions.
Figure 17: Average Power Main effect on DW
Subjective Data and Feedback
Pilot Strategies and Feedback on DW Design
The majority (10 out of 12) of the pilots
commented that they used the altitude and speed
deviations at the DWs as feedback to manage the
descent. Specifically they strategized that when
coming in too fast to a DW target they would reduce
vertical speed, and when coming in too slow to a DW
target they would increase vertical speed. This
strategy was used in combination with their rule
thumb for managing vertical speed, which is for
every three miles the aircraft descends 1,000 feet.
They also reported using the speed brakes as little as
possible and using the flaps only as needed.
In terms of the placement of the DWs, the pilots
mentioned that they like the spacing between each
DW target and how the 10,000 feet level off section
(Alt<10: DW Target 3) helped slow down the
aircraft. One pilot said that it was difficult for him to
slow down at 10,000 feet from 240 IAS to 160 IAS
until the end of the scenario because of the workload
of using the speed brakes and setting the flaps. They
recommended that the distance between two DWs be
between 10nm to 30nm apart when they are further
away the airport, and 5nm to 10nm when precision
flight is needed closer to airport. Overall, the mean
for pilot rating of the effectiveness of the DW target
locations on the flight plan were 4.67 out of six
(where 1 is very uncomfortable and 6 is very
comfortable).
In terms of power management, the pilots stated
that DW helps reduce power usage of the aircraft if
the descent was planned correctly to intercept DW
altitude without leveling out. If the aircraft is early to
the target altitude before DW target, it creates level
off altitude segments, which increases power usage.
Pilots commented that with the green arc (altitude
prediction tool) in their NAV display, they would get
to the DW altitude target without leveling off.
Perceived Workload
The results from a 3x1 (DW x Wind) within-
subject analysis of variance (ANOVA) revealed a
significant main effect of DW on perceived
workload, F(1.496, 16.451)=77, p<0.000,
etap
2
=1.000. In the one DW condition, (mean=2.58
sd=0.67) significant differences in workload were
found compared to the three DW condition
(mean=3.25 sd=0.75) and the five DW condition
(mean=4.17 sd=0.72). The difference between the
one three DW condition was 0.67 perceived
workload, between the three one DW condition was
0.92 perceived workload, and between the five DW
and one DW condition was 1.59 perceived workload.
Figure 18 shows the mean workload for each DW
condition. A likert scale was used to assess workload
(where 1 is very low and 6 is very high).
0.00
2.00
4.00
6.00
8.00
10.00
12.00
14.00
1 DW 3 DW 5 DW
AveragePowerPercentage
11. 11
Figure 18: Average Perceived Workload Main
effect on DW
Feedback on Flight Chart, Vertical View on
CSD , and CDA scenarios
The pilots rated the usefulness of a using a
vertical flight chart integrated with DW information
with a mean score of 4.42 out of 6 with a standard
deviation (SD) of 1. Most pilots liked the provided
DW flight chart, and commented that they would like
the DW information much better if used in
combination with the Jeppesen chart, and preferred to
have the distance to next DW and descent angles
(based on ground speeds) be inserted into DW flight
chart.
In terms of the utility of the vertical view on the
CSD for maintaining the flight plan, the pilots rated
its usefulness with a mean score of 3.75 out of 6 with
a SD of 1.22. They suggested a number of additional
features and information to be added to the CSD,
including thicker flight path, known vertical
deviation from flight path, a green arc ("banana" for
altitude confirmation), and an option to zoom in and
out. A Boeing 757 pilot said that his cockpit setup
(vertical NAV screen is next to the regular NAV
screen on the right) is similar to what was done in the
study and has an energy management arrow (similar
to Figure 3) which is helpful for flying CDA.
For the CDA scenario designed in the study, the
pilots thought that scenarios were realistic and that
they would have flown better with the help of a pilot
monitoring (PM) and with tools such as the green arc.
They suggested that the roles of the pilot flying (PF)
would be able to fly vertical speed and IAS, make
decisions for meeting DWs, and vocalize plan and
callouts to the PM. As for the roles of the PM, they
suggested that the PM monitor targets, air speed,
IAS, and DWs; do all calculations for the PF; set
altitudes, MCP; work the gear and flaps; crosscheck
altitude inputs; and communicate with ATC.
Conclusions
In this paper, descriptive waypoints were
proposed as a viable near-term method to assist pilots
in performing CDA procedures that start further away
from the airport than CDAs used in current practice.
It was hypothesized that the pilot performance would
improve as the number the descriptive waypoint
increases, and the results in the experiment
corroborate this notion. As indicated in the
experimental results and pilot feedback, the
descriptive waypoints act as a feedback mechanism
that help “reset” the system by allowing the pilots to
make adjustments based on the altitude deviations
from the targets at the descriptive waypoints. The
Five-DW condition (the condition with the most
number of descriptive waypoints) resulted in only
one percent more in power than the other conditions
and with a slight increase in workload. With
automated assistance (such as the green arc), the
pilots believed that they would use less power by
intercepting the DW altitude target without resorting
to level flight. The potential small increase in
workload could be addressed by developing
procedures that assign the pilot monitoring the task of
monitoring the deviations at the DW targets and
vocalizing plans to meet the next targets.
In combination, proper design of the descriptive
waypoints’ locations and targets and of the
approach’s vertical and speed profiles allowed pilots
to fly the approach consistently, which will help ATC
with aircraft separation and ultimately make CDA
more feasible in high traffic conditions. For future
development, the DWs can be implemented into the
current flight charts for near term implementation,
and for midterm, they can integrated into more
advanced software that would provide power
management and dynamically update DW altitude
and IAS targets based on wind speed and constraints
on arrival time.
0
1
2
3
4
5
1 DW 3 DW 5 DW
AveragePerceivedWorkload
12. 12
References
[1] Lowther, M. B., Clarke, J-P., & Ren, L.,
(2007). En Route Speed Change
Optimization for Spacing Continuous
Descent Arrivals
[2] Reynolds, H., Reynolds, T. & R. Hansman, J.
(2005). Human Factors Implications of
Continuous Descent Approach Procedures
for Noise Abatement in Air Traffic Control.
6th USA/Europe Air Traffic Management
R&D Seminar, Baltimore, USA, June 27-30.
[3] Ho, N. T., Clarke, J-P., Riedel, R., & Omen,
C. (2006). Development and Evaluation of a
Pilot Cueing System for Near-Term
Implementation of Aircraft Noise Abatement
Approach Procedures. Journal of American
Institute of Aeronautics and Astronautics.
[4] Clarke, J-P., B., Ho, N. T., Ren, L., Brown, J.
A., Elmer, K. R., Tong, K-O & Wat, J. K.
(2004). Continuous Descent Approach:
Design and Flight Test for Louisville
International Airport. Journal of Aircraft,
41(5), 1054-1066.
[5] Reynolds, H. (2006). Modeling the Air
Traffic Controller’s Cognitive Projection
Process. MIT International Center for Air
Transportation Department of Aeronautics &
Astronautics Massachusetts Institute of
Technology Cambridge, MA, 2006
[6] Stell, L. (2010). Predictability of Top of
Descent Location for operational Idle-thrust
Descents. American Institute of Aeronautics
and Astronautics.
[7] Kupfer, M., Callantine, T., Martin, L.,
Mercer, J. & Palmer, E., 2011, Controller
Support Tools for Schedule-Based Terminal-
Area Operations, Ninth USA/Europe Air
Traffic Management Research and
Development Seminar (ATM2011)
[8] Alam, S, Nguyen, M.H., Abbass, H.A.,
Lokan, C., Ellejmi, M., & Kirby, S., 2010, A
Dynamic Continuous Descent Approach
Methodology for Low Noise and Emission,
29th IEEE/AIAA Digital Avionics Systems
Conference, October 3-7, 2010
[9] Ren, L. & Clark, J-P., 2007, Flight
Demonstration of the Separation Analysis
Methodology for Continuous Descent
Arrival, Draft paper for 7th USA/Europe
ATM 2007 R&D Seminar, Barcelona, Spain,
2-5 July 2007.
[10] Clark, J-P., Bennett, D., Elmer, K.,
Firth, J., Hilb, R., Ho, N., Johnson, S., Lau,
S., Ren, L., Senechal, D., Sizov, N., Slattery,
R., Tong, K., Walton, J., Willgruber, A.,
Williams, D. (2006). Development, Design,
and Flight Test Evaluation of a Continuous
Descent Approach Procedure for Nighttime
Operation at Louisville International Airport
[11] Koeslag, M. F., (1999) Advanced
Continuous Descent Approaches –An
algorithm design for the Flight Management
System-.
[12] Moore, S. (2009). Benefits of
Highly Predictable Flight Trajectories in
Performing Routine Optimized Profile
Descents: Current and Recommended
Research. Environmental Working Group
Operations Standing Committee 2009
Annual Workshop, NASA Ames.
[13] Williams, D. (2008). Flight Deck
Merging and Spacing and Advanced FMS
Operations. EWG Operations Standing
Committee Meeting.
[14] Coppenbarger, R., Mead, R., Sweet,
D., (2009). Field Evaluation of the Tailored
Arrivals Concept for Datalink-Enabled
Continuous Descent Approach. Journal of
Aircraft, 46(4), July–August 2009
[15] Global Aviation Navigation, Inc.,
(2009). Retrieved May 2009, from
http://www.globalair.com/d-
TPP_pdf/00239IL17R.PDF
[16] Thomas, L. & Wickens, C. (2006).
Individual Effects of Battlefield Display
Frames of Reference on Navigation Tasks,
Spatial Judgments, and Change Detection.
Ergonomics, 49, 154-1173.
[17] Cowen, M., John, M., Oonk, H., &
Smallman, H. (2001). The Use of 2D and 3D
Displays for Shape-Understanding versus
13. 13
Relative-Position Tasks. Human Factors,
43(1), 79-98.
[18] Symmes, D., & Pella, J. (2005).
Three-Dimensional Image. Microsoft®
Encarta® 2006 [CD]. Redmond, WA:
Microsoft Corporation, 2005.
[19] Prevot, T., (1998). A Display for
Managing the Vertical Flight Path - an
Appropriate Task with Inappropriate
Feedback-. International Conference on
Human-Computer Interaction in Aeronautics
Montreal, Canada, 1998
[20] Johnson, W., Ho, N., Martin, P., Vu,
K-P., Ligda, S., Battiste, V., Lachter, J., Dao,
A. (2010), “Management Of Continuous
Descent Approaches During Interval
Management Operations,” 29th Digital
Avionics Systems Conference, Salt Lake
City, Utah.
[21] Prevot, T., Callatine, T., Kopardekar,
P., Smith, N., Palmer, E., Battiste, V., (2004).
Trajectory-Oriented Operations with Limited
Delegation: An Evolutionary Path to NAS
Modernization. AIAA 4th Aviation
Technology, Integration and Operations
(ATIO) Forum, Chicago, IL, September
2004.
30th Digital Avionics Systems Conference
October 16-20, 2011